| Message ID | 1534227134-151584-2-git-send-email-hanjie.lin@amlogic.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | add the Amlogic Meson PCIe phy driver. | expand |
On Tue, Aug 14, 2018 at 02:12:13AM -0400, Hanjie Lin wrote: > From: Yue Wang <yue.wang@amlogic.com> Subject should be "dt-bindings: phy: ..." > The Meson-PCIE-PHY controller supports the 5-Gbps data rate > of the PCI Express Gen 2 specification and is backwardcompatible space ^ > with the 2.5-Gbps Gen 1.1 specification with only > inferred idle detection supported on AMLOGIC SoCs. AMLOGIC or Amlogic? > > Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com> > Signed-off-by: Yue Wang <yue.wang@amlogic.com> > --- > .../bindings/phy/amlogic,meson-pcie-phy.txt | 31 ++++++++++++++++++++++ > 1 file changed, 31 insertions(+) > create mode 100644 Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt > > diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt > new file mode 100644 > index 0000000..db99085 > --- /dev/null > +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt > @@ -0,0 +1,31 @@ > +* Amlogic Meson AXG PCIE PHY binding > + > +Required properties: > +- compatible: Should be > + - "amlogic,axg-pcie-phy" > +- #phys-cells: must be 0 (see phy-bindings.txt in this directory) You don't need to distinguish port A and B? > +- reg: The base address and length of the registers > +- resets: phandle to the reset lines > +- reset-names: must contain "phy" and "peripheral" > + - "port_a" Port A reset > + - "port_b" Port B reset > + - "phy" PHY reset > + - "apb" APB reset > +Optional properties: > +- phy-supply: see phy-bindings.txt in this directory > + > +Example: > + pcie_phy: pcie-phy@ff644000 { > + #phy-cells = <0>; > + compatible = "amlogic,axg-pcie-phy"; > + reg = <0x0 0xff644000 0x0 0x2000>; > + resets = <&reset RESET_PCIE_A>, > + <&reset RESET_PCIE_B>, > + <&reset RESET_PCIE_PHY>, > + <&reset RESET_PCIE_APB>; > + reset-names = > + "port_a", > + "port_b", > + "phy", > + "apb"; > + }; > -- > 2.7.4 >
On 2018/8/15 6:50, Rob Herring wrote: > On Tue, Aug 14, 2018 at 02:12:13AM -0400, Hanjie Lin wrote: >> From: Yue Wang <yue.wang@amlogic.com> > > Subject should be "dt-bindings: phy: ..." > >> The Meson-PCIE-PHY controller supports the 5-Gbps data rate >> of the PCI Express Gen 2 specification and is backwardcompatible > > space yes, I will fix ^ > >> with the 2.5-Gbps Gen 1.1 specification with only >> inferred idle detection supported on AMLOGIC SoCs. > > AMLOGIC or Amlogic? > yes, we will stick to 'Amlogic' >> >> Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com> >> Signed-off-by: Yue Wang <yue.wang@amlogic.com> >> --- >> .../bindings/phy/amlogic,meson-pcie-phy.txt | 31 ++++++++++++++++++++++ >> 1 file changed, 31 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt >> >> diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt >> new file mode 100644 >> index 0000000..db99085 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt >> @@ -0,0 +1,31 @@ >> +* Amlogic Meson AXG PCIE PHY binding >> + >> +Required properties: >> +- compatible: Should be >> + - "amlogic,axg-pcie-phy" >> +- #phys-cells: must be 0 (see phy-bindings.txt in this directory) > > You don't need to distinguish port A and B? No, we don't. Theoretically there is only one phy in the chip, and we have distinguished ports by reset lines. Thanks for all corrections and suggestions. > >> +- reg: The base address and length of the registers >> +- resets: phandle to the reset lines >> +- reset-names: must contain "phy" and "peripheral" >> + - "port_a" Port A reset >> + - "port_b" Port B reset >> + - "phy" PHY reset >> + - "apb" APB reset >> +Optional properties: >> +- phy-supply: see phy-bindings.txt in this directory >> + >> +Example: >> + pcie_phy: pcie-phy@ff644000 { >> + #phy-cells = <0>; >> + compatible = "amlogic,axg-pcie-phy"; >> + reg = <0x0 0xff644000 0x0 0x2000>; >> + resets = <&reset RESET_PCIE_A>, >> + <&reset RESET_PCIE_B>, >> + <&reset RESET_PCIE_PHY>, >> + <&reset RESET_PCIE_APB>; >> + reset-names = >> + "port_a", >> + "port_b", >> + "phy", >> + "apb"; >> + }; >> -- >> 2.7.4 >> > > . >
diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt new file mode 100644 index 0000000..db99085 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt @@ -0,0 +1,31 @@ +* Amlogic Meson AXG PCIE PHY binding + +Required properties: +- compatible: Should be + - "amlogic,axg-pcie-phy" +- #phys-cells: must be 0 (see phy-bindings.txt in this directory) +- reg: The base address and length of the registers +- resets: phandle to the reset lines +- reset-names: must contain "phy" and "peripheral" + - "port_a" Port A reset + - "port_b" Port B reset + - "phy" PHY reset + - "apb" APB reset +Optional properties: +- phy-supply: see phy-bindings.txt in this directory + +Example: + pcie_phy: pcie-phy@ff644000 { + #phy-cells = <0>; + compatible = "amlogic,axg-pcie-phy"; + reg = <0x0 0xff644000 0x0 0x2000>; + resets = <&reset RESET_PCIE_A>, + <&reset RESET_PCIE_B>, + <&reset RESET_PCIE_PHY>, + <&reset RESET_PCIE_APB>; + reset-names = + "port_a", + "port_b", + "phy", + "apb"; + };