| Message ID | 1311246554-22975-4-git-send-email-shubhrajyoti@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 7/21/2011 4:39 PM, Shubhrajyoti D wrote: > The reset in the driver at init is not needed > anymore as the hwmod framework takes care of > reseting it. > > Signed-off-by: Shubhrajyoti D<shubhrajyoti@ti.com> > --- > drivers/i2c/busses/i2c-omap.c | 73 ++++++++++++---------------------------- > 1 files changed, 22 insertions(+), 51 deletions(-) Excellent cleanup. Some minor coments > > diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c > index 8f87a37..8dc54d5 100644 > --- a/drivers/i2c/busses/i2c-omap.c > +++ b/drivers/i2c/busses/i2c-omap.c > @@ -155,9 +155,6 @@ enum { > #define OMAP_I2C_SYSTEST_SDA_O (1<< 0) /* SDA line drive out */ > #endif > > -/* OCP_SYSSTATUS bit definitions */ > -#define SYSS_RESETDONE_MASK (1<< 0) > - > /* OCP_SYSCONFIG bit definitions */ > #define SYSC_CLOCKACTIVITY_MASK (0x3<< 8) > #define SYSC_SIDLEMODE_MASK (0x3<< 3) > @@ -182,6 +179,7 @@ struct omap_i2c_dev { > u32 latency; /* maximum mpu wkup latency */ > void (*set_mpu_wkup_lat)(struct device *dev, > long latency); > + int (*device_reset)(struct device *dev); > u32 speed; /* Speed of bus in Khz */ > u16 cmd_err; > u8 *buf; > @@ -332,7 +330,6 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) > u16 psc = 0, scll = 0, sclh = 0, buf = 0; > u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0; > unsigned long fclk_rate = 12000000; > - unsigned long timeout; > unsigned long internal_clk = 0; > struct clk *fclk; > struct platform_device *pdev; > @@ -341,53 +338,16 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) > pdev = to_platform_device(dev->dev); > pdata = pdev->dev.platform_data; > > - if (dev->rev>= OMAP_I2C_OMAP1_REV_2) { > - /* Disable I2C controller before soft reset */ > - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, > - omap_i2c_read_reg(dev, OMAP_I2C_CON_REG)& > - ~(OMAP_I2C_CON_EN)); > - > - omap_i2c_write_reg(dev, OMAP_I2C_SYSC_REG, SYSC_SOFTRESET_MASK); > - /* For some reason we need to set the EN bit before the > - * reset done bit gets set. */ > - timeout = jiffies + OMAP_I2C_TIMEOUT; > - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); > - while (!(omap_i2c_read_reg(dev, OMAP_I2C_SYSS_REG)& > - SYSS_RESETDONE_MASK)) { > - if (time_after(jiffies, timeout)) { > - dev_warn(dev->dev, "timeout waiting " > - "for controller reset\n"); > - return -ETIMEDOUT; > - } > - msleep(1); > - } > - > - /* SYSC register is cleared by the reset; rewrite it */ > - if (dev->rev == OMAP_I2C_REV_ON_2430) { > - > - omap_i2c_write_reg(dev, OMAP_I2C_SYSC_REG, > - SYSC_AUTOIDLE_MASK); > - > - } else if (dev->rev>= OMAP_I2C_REV_ON_3430) { > - dev->syscstate = SYSC_AUTOIDLE_MASK; > - dev->syscstate |= SYSC_ENAWAKEUP_MASK; > - dev->syscstate |= (SYSC_IDLEMODE_SMART<< > - __ffs(SYSC_SIDLEMODE_MASK)); > - dev->syscstate |= (SYSC_CLOCKACTIVITY_FCLK<< > - __ffs(SYSC_CLOCKACTIVITY_MASK)); > - > - omap_i2c_write_reg(dev, OMAP_I2C_SYSC_REG, > - dev->syscstate); > - /* > - * Enabling all wakup sources to stop I2C freezing on > - * WFI instruction. > - * REVISIT: Some wkup sources might not be needed. > - */ > - dev->westate = OMAP_I2C_WE_ALL; > - if (dev->rev< OMAP_I2C_REV_ON_3530_4430) > - omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, > - dev->westate); > - } > + if (dev->rev>= OMAP_I2C_REV_ON_3430) { Space please if (dev->rev >= OMAP_I2C_REV_ON_3430) { > + /* > + * Enabling all wakup sources to stop I2C freezing on > + * WFI instruction. > + * REVISIT: Some wkup sources might not be needed. > + */ Surely not related to your patch. But the 'REVISIT:' caught my attention. Is the comment still valid. > + dev->westate = OMAP_I2C_WE_ALL; > + if (dev->rev< OMAP_I2C_REV_ON_3530_4430) Space if (dev->rev < OMAP_I2C_REV_ON_3530_4430) > + omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, > + dev->westate); > } > omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); > > @@ -612,6 +572,11 @@ static int omap_i2c_xfer_msg(struct i2c_adapter *adap, > return r; > if (r == 0) { > dev_err(dev->dev, "controller timed out\n"); > + if (dev->device_reset != NULL) { > + r = dev->device_reset(dev->dev); > + if (r< 0) ditto > + dev_err(dev->dev, "reset failed\n"); > + } > omap_i2c_init(dev); > return -ETIMEDOUT; > } > @@ -622,6 +587,11 @@ static int omap_i2c_xfer_msg(struct i2c_adapter *adap, > /* We have an error */ > if (dev->cmd_err& (OMAP_I2C_STAT_AL | OMAP_I2C_STAT_ROVR | You can fix this one as well. > OMAP_I2C_STAT_XUDF)) { > + if (dev->device_reset != NULL) { > + r = dev->device_reset(dev->dev); > + if (r< 0) here too. > + dev_err(dev->dev, "reset failed\n"); > + } > omap_i2c_init(dev); > return -EIO; > } > @@ -1024,6 +994,7 @@ omap_i2c_probe(struct platform_device *pdev) > if (pdata != NULL) { > speed = pdata->clkrate; > dev->set_mpu_wkup_lat = pdata->set_mpu_wkup_lat; > + dev->device_reset = pdata->device_reset; > } else { > speed = 100; /* Default speed */ > dev->set_mpu_wkup_lat = NULL; Regards Santosh -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thursday 21 July 2011 04:57 PM, Santosh Shilimkar wrote: Thanks for your review. > On 7/21/2011 4:39 PM, Shubhrajyoti D wrote: > <snip> >> + /* >> + * Enabling all wakup sources to stop I2C freezing on >> + * WFI instruction. >> + * REVISIT: Some wkup sources might not be needed. >> + */ > Surely not related to your patch. But the 'REVISIT:' caught > my attention. Is the comment still valid. Yes I will look and optimise the settings. Obviously all of them may not be needed. Will get back on this. Also I see that we are not writing it for " < OMAP_I2C_REV_ON_3530_4430" I will send a patch correcting the same. > >> + dev->westate = OMAP_I2C_WE_ALL; >> + if (dev->rev< OMAP_I2C_REV_ON_3530_4430) > Space if (dev->rev < OMAP_I2C_REV_ON_3530_4430) >> + omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, >> + dev->westate); >> } >> omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); >> >> @@ -612,6 +572,11 @@ static int omap_i2c_xfer_msg(struct i2c_adapter >> *adap, >> return r; >> if (r == 0) { >> dev_err(dev->dev, "controller timed out\n"); >> + if (dev->device_reset != NULL) { >> + r = dev->device_reset(dev->dev); >> + if (r< 0) > ditto >> + dev_err(dev->dev, "reset failed\n"); >> + } >> omap_i2c_init(dev); >> return -ETIMEDOUT; >> } >> @@ -622,6 +587,11 @@ static int omap_i2c_xfer_msg(struct i2c_adapter >> *adap, >> /* We have an error */ >> if (dev->cmd_err& (OMAP_I2C_STAT_AL | OMAP_I2C_STAT_ROVR | > You can fix this one as well. >> OMAP_I2C_STAT_XUDF)) { >> + if (dev->device_reset != NULL) { >> + r = dev->device_reset(dev->dev); >> + if (r< 0) > here too. >> + dev_err(dev->dev, "reset failed\n"); >> + } >> omap_i2c_init(dev); >> return -EIO; >> } >> @@ -1024,6 +994,7 @@ omap_i2c_probe(struct platform_device *pdev) >> if (pdata != NULL) { >> speed = pdata->clkrate; >> dev->set_mpu_wkup_lat = pdata->set_mpu_wkup_lat; >> + dev->device_reset = pdata->device_reset; >> } else { >> speed = 100; /* Default speed */ >> dev->set_mpu_wkup_lat = NULL; > > Regards > Santosh -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 8f87a37..8dc54d5 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -155,9 +155,6 @@ enum { #define OMAP_I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive out */ #endif -/* OCP_SYSSTATUS bit definitions */ -#define SYSS_RESETDONE_MASK (1 << 0) - /* OCP_SYSCONFIG bit definitions */ #define SYSC_CLOCKACTIVITY_MASK (0x3 << 8) #define SYSC_SIDLEMODE_MASK (0x3 << 3) @@ -182,6 +179,7 @@ struct omap_i2c_dev { u32 latency; /* maximum mpu wkup latency */ void (*set_mpu_wkup_lat)(struct device *dev, long latency); + int (*device_reset)(struct device *dev); u32 speed; /* Speed of bus in Khz */ u16 cmd_err; u8 *buf; @@ -332,7 +330,6 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) u16 psc = 0, scll = 0, sclh = 0, buf = 0; u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0; unsigned long fclk_rate = 12000000; - unsigned long timeout; unsigned long internal_clk = 0; struct clk *fclk; struct platform_device *pdev; @@ -341,53 +338,16 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) pdev = to_platform_device(dev->dev); pdata = pdev->dev.platform_data; - if (dev->rev >= OMAP_I2C_OMAP1_REV_2) { - /* Disable I2C controller before soft reset */ - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, - omap_i2c_read_reg(dev, OMAP_I2C_CON_REG) & - ~(OMAP_I2C_CON_EN)); - - omap_i2c_write_reg(dev, OMAP_I2C_SYSC_REG, SYSC_SOFTRESET_MASK); - /* For some reason we need to set the EN bit before the - * reset done bit gets set. */ - timeout = jiffies + OMAP_I2C_TIMEOUT; - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); - while (!(omap_i2c_read_reg(dev, OMAP_I2C_SYSS_REG) & - SYSS_RESETDONE_MASK)) { - if (time_after(jiffies, timeout)) { - dev_warn(dev->dev, "timeout waiting " - "for controller reset\n"); - return -ETIMEDOUT; - } - msleep(1); - } - - /* SYSC register is cleared by the reset; rewrite it */ - if (dev->rev == OMAP_I2C_REV_ON_2430) { - - omap_i2c_write_reg(dev, OMAP_I2C_SYSC_REG, - SYSC_AUTOIDLE_MASK); - - } else if (dev->rev >= OMAP_I2C_REV_ON_3430) { - dev->syscstate = SYSC_AUTOIDLE_MASK; - dev->syscstate |= SYSC_ENAWAKEUP_MASK; - dev->syscstate |= (SYSC_IDLEMODE_SMART << - __ffs(SYSC_SIDLEMODE_MASK)); - dev->syscstate |= (SYSC_CLOCKACTIVITY_FCLK << - __ffs(SYSC_CLOCKACTIVITY_MASK)); - - omap_i2c_write_reg(dev, OMAP_I2C_SYSC_REG, - dev->syscstate); - /* - * Enabling all wakup sources to stop I2C freezing on - * WFI instruction. - * REVISIT: Some wkup sources might not be needed. - */ - dev->westate = OMAP_I2C_WE_ALL; - if (dev->rev < OMAP_I2C_REV_ON_3530_4430) - omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, - dev->westate); - } + if (dev->rev >= OMAP_I2C_REV_ON_3430) { + /* + * Enabling all wakup sources to stop I2C freezing on + * WFI instruction. + * REVISIT: Some wkup sources might not be needed. + */ + dev->westate = OMAP_I2C_WE_ALL; + if (dev->rev < OMAP_I2C_REV_ON_3530_4430) + omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, + dev->westate); } omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); @@ -612,6 +572,11 @@ static int omap_i2c_xfer_msg(struct i2c_adapter *adap, return r; if (r == 0) { dev_err(dev->dev, "controller timed out\n"); + if (dev->device_reset != NULL) { + r = dev->device_reset(dev->dev); + if (r < 0) + dev_err(dev->dev, "reset failed\n"); + } omap_i2c_init(dev); return -ETIMEDOUT; } @@ -622,6 +587,11 @@ static int omap_i2c_xfer_msg(struct i2c_adapter *adap, /* We have an error */ if (dev->cmd_err & (OMAP_I2C_STAT_AL | OMAP_I2C_STAT_ROVR | OMAP_I2C_STAT_XUDF)) { + if (dev->device_reset != NULL) { + r = dev->device_reset(dev->dev); + if (r < 0) + dev_err(dev->dev, "reset failed\n"); + } omap_i2c_init(dev); return -EIO; } @@ -1024,6 +994,7 @@ omap_i2c_probe(struct platform_device *pdev) if (pdata != NULL) { speed = pdata->clkrate; dev->set_mpu_wkup_lat = pdata->set_mpu_wkup_lat; + dev->device_reset = pdata->device_reset; } else { speed = 100; /* Default speed */ dev->set_mpu_wkup_lat = NULL;
The reset in the driver at init is not needed anymore as the hwmod framework takes care of reseting it. Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> --- drivers/i2c/busses/i2c-omap.c | 73 ++++++++++++---------------------------- 1 files changed, 22 insertions(+), 51 deletions(-)