Message ID | 1537252429-8655-1-git-send-email-mkenna@codeaurora.org (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Series | ath10k: Advertize beacon_int_min_gcd as 100 while bring up multi vaps | expand |
On 09/17/2018 11:33 PM, Maharaja Kennadyrajan wrote: > With the latest firmware design, the beacon interval should be > greater than 100 to bring the multiple vaps. > > Set beacon_int_min_gcd to 100, when the wmi service > WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT is enabled > in the firmware. If not, beacon_int_min_gcd will be set > to the default value 1. > > Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00015 > Tested in QCA9888 with firmware ver 10.4-3.5.1-0005 > > Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org> > --- > drivers/net/wireless/ath/ath10k/mac.c | 25 +++++++++++++++++++++++++ > drivers/net/wireless/ath/ath10k/wmi.h | 9 +++++++++ > 2 files changed, 34 insertions(+) > > diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c > index 97548f9..532fc5d 100644 > --- a/drivers/net/wireless/ath/ath10k/mac.c > +++ b/drivers/net/wireless/ath/ath10k/mac.c > @@ -8163,6 +8163,24 @@ void ath10k_mac_destroy(struct ath10k *ar) > }, > }; > > +static const struct > +ieee80211_iface_combination ath10k_10_4_bcn_int_if_comb[] = { > + { > + .limits = ath10k_10_4_if_limits, > + .n_limits = ARRAY_SIZE(ath10k_10_4_if_limits), > + .max_interfaces = 16, > + .num_different_channels = 1, > + .beacon_int_infra_match = true, > + .beacon_int_min_gcd = 100, > +#ifdef CONFIG_ATH10K_DFS_CERTIFIED > + .radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) | > + BIT(NL80211_CHAN_WIDTH_20) | > + BIT(NL80211_CHAN_WIDTH_40) | > + BIT(NL80211_CHAN_WIDTH_80), > +#endif > + }, > +}; > + > static void ath10k_get_arvif_iter(void *data, u8 *mac, > struct ieee80211_vif *vif) > { > @@ -8526,6 +8544,13 @@ int ath10k_mac_register(struct ath10k *ar) > ar->hw->wiphy->iface_combinations = ath10k_10_4_if_comb; > ar->hw->wiphy->n_iface_combinations = > ARRAY_SIZE(ath10k_10_4_if_comb); > + if (test_bit(WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, > + ar->wmi.svc_map)) { > + ar->hw->wiphy->iface_combinations = > + ath10k_10_4_bcn_int_if_comb; > + ar->hw->wiphy->n_iface_combinations = > + ARRAY_SIZE(ath10k_10_4_bcn_int_if_comb); > + } > break; > case ATH10K_FW_WMI_OP_VERSION_UNSET: > case ATH10K_FW_WMI_OP_VERSION_MAX: > diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h > index 1562294..126eb17 100644 > --- a/drivers/net/wireless/ath/ath10k/wmi.h > +++ b/drivers/net/wireless/ath/ath10k/wmi.h > @@ -204,6 +204,7 @@ enum wmi_service { > WMI_SERVICE_RESET_CHIP, > WMI_SERVICE_SPOOF_MAC_SUPPORT, > WMI_SERVICE_TX_DATA_ACK_RSSI, > + WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, > > /* keep last */ > WMI_SERVICE_MAX, > @@ -353,6 +354,11 @@ enum wmi_10_4_service { > WMI_10_4_SERVICE_TPC_STATS_FINAL, > WMI_10_4_SERVICE_CFR_CAPTURE_SUPPORT, > WMI_10_4_SERVICE_TX_DATA_ACK_RSSI, > + WMI_10_4_SERVICE_CFR_CAPTURE_IND_MSG_TYPE_LAGACY, That should end with "LEGACY" instead of "LAGACY" maybe? > + WMI_10_4_SERVICE_PER_PACKET_SW_ENCRYPT, > + WMI_10_4_SERVICE_PEER_TID_CONFIGS_SUPPORT, > + WMI_10_4_SERVICE_VDEV_BCN_RATE_CONTROL, > + WMI_10_4_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, > }; > > static inline char *wmi_service_name(int service_id) > @@ -467,6 +473,7 @@ static inline char *wmi_service_name(int service_id) > SVCSTR(WMI_SERVICE_TPC_STATS_FINAL); > SVCSTR(WMI_SERVICE_RESET_CHIP); > SVCSTR(WMI_SERVICE_TX_DATA_ACK_RSSI); > + SVCSTR(WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT); > default: > return NULL; > } > @@ -777,6 +784,8 @@ static inline void wmi_10_4_svc_map(const __le32 *in, unsigned long *out, > WMI_SERVICE_TPC_STATS_FINAL, len); > SVCMAP(WMI_10_4_SERVICE_TX_DATA_ACK_RSSI, > WMI_SERVICE_TX_DATA_ACK_RSSI, len); > + SVCMAP(WMI_10_4_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, > + WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, len); > } > > #undef SVCMAP > Thanks, Ben
On 2018-09-18 4:14 pm, Ben Greear wrote: > On 09/17/2018 11:33 PM, Maharaja Kennadyrajan wrote: >> With the latest firmware design, the beacon interval should be >> greater than 100 to bring the multiple vaps. >> >> Set beacon_int_min_gcd to 100, when the wmi service >> WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT is enabled >> in the firmware. If not, beacon_int_min_gcd will be set >> to the default value 1. >> >> Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00015 >> Tested in QCA9888 with firmware ver 10.4-3.5.1-0005 >> >> Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org> >> --- >> drivers/net/wireless/ath/ath10k/mac.c | 25 +++++++++++++++++++++++++ >> drivers/net/wireless/ath/ath10k/wmi.h | 9 +++++++++ >> 2 files changed, 34 insertions(+) >> >> diff --git a/drivers/net/wireless/ath/ath10k/mac.c >> b/drivers/net/wireless/ath/ath10k/mac.c >> index 97548f9..532fc5d 100644 >> --- a/drivers/net/wireless/ath/ath10k/mac.c >> +++ b/drivers/net/wireless/ath/ath10k/mac.c >> @@ -8163,6 +8163,24 @@ void ath10k_mac_destroy(struct ath10k *ar) >> }, >> }; >> >> +static const struct >> +ieee80211_iface_combination ath10k_10_4_bcn_int_if_comb[] = { >> + { >> + .limits = ath10k_10_4_if_limits, >> + .n_limits = ARRAY_SIZE(ath10k_10_4_if_limits), >> + .max_interfaces = 16, >> + .num_different_channels = 1, >> + .beacon_int_infra_match = true, >> + .beacon_int_min_gcd = 100, >> +#ifdef CONFIG_ATH10K_DFS_CERTIFIED >> + .radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) | >> + BIT(NL80211_CHAN_WIDTH_20) | >> + BIT(NL80211_CHAN_WIDTH_40) | >> + BIT(NL80211_CHAN_WIDTH_80), >> +#endif >> + }, >> +}; >> + >> static void ath10k_get_arvif_iter(void *data, u8 *mac, >> struct ieee80211_vif *vif) >> { >> @@ -8526,6 +8544,13 @@ int ath10k_mac_register(struct ath10k *ar) >> ar->hw->wiphy->iface_combinations = ath10k_10_4_if_comb; >> ar->hw->wiphy->n_iface_combinations = >> ARRAY_SIZE(ath10k_10_4_if_comb); >> + if (test_bit(WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, >> + ar->wmi.svc_map)) { >> + ar->hw->wiphy->iface_combinations = >> + ath10k_10_4_bcn_int_if_comb; >> + ar->hw->wiphy->n_iface_combinations = >> + ARRAY_SIZE(ath10k_10_4_bcn_int_if_comb); >> + } >> break; >> case ATH10K_FW_WMI_OP_VERSION_UNSET: >> case ATH10K_FW_WMI_OP_VERSION_MAX: >> diff --git a/drivers/net/wireless/ath/ath10k/wmi.h >> b/drivers/net/wireless/ath/ath10k/wmi.h >> index 1562294..126eb17 100644 >> --- a/drivers/net/wireless/ath/ath10k/wmi.h >> +++ b/drivers/net/wireless/ath/ath10k/wmi.h >> @@ -204,6 +204,7 @@ enum wmi_service { >> WMI_SERVICE_RESET_CHIP, >> WMI_SERVICE_SPOOF_MAC_SUPPORT, >> WMI_SERVICE_TX_DATA_ACK_RSSI, >> + WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, >> >> /* keep last */ >> WMI_SERVICE_MAX, >> @@ -353,6 +354,11 @@ enum wmi_10_4_service { >> WMI_10_4_SERVICE_TPC_STATS_FINAL, >> WMI_10_4_SERVICE_CFR_CAPTURE_SUPPORT, >> WMI_10_4_SERVICE_TX_DATA_ACK_RSSI, >> + WMI_10_4_SERVICE_CFR_CAPTURE_IND_MSG_TYPE_LAGACY, > > That should end with "LEGACY" instead of "LAGACY" maybe? [Maha]: Thanks Ben for noticing it. I will take care it in v2 patch. > >> + WMI_10_4_SERVICE_PER_PACKET_SW_ENCRYPT, >> + WMI_10_4_SERVICE_PEER_TID_CONFIGS_SUPPORT, >> + WMI_10_4_SERVICE_VDEV_BCN_RATE_CONTROL, >> + WMI_10_4_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, >> }; >> >> static inline char *wmi_service_name(int service_id) >> @@ -467,6 +473,7 @@ static inline char *wmi_service_name(int >> service_id) >> SVCSTR(WMI_SERVICE_TPC_STATS_FINAL); >> SVCSTR(WMI_SERVICE_RESET_CHIP); >> SVCSTR(WMI_SERVICE_TX_DATA_ACK_RSSI); >> + SVCSTR(WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT); >> default: >> return NULL; >> } >> @@ -777,6 +784,8 @@ static inline void wmi_10_4_svc_map(const __le32 >> *in, unsigned long *out, >> WMI_SERVICE_TPC_STATS_FINAL, len); >> SVCMAP(WMI_10_4_SERVICE_TX_DATA_ACK_RSSI, >> WMI_SERVICE_TX_DATA_ACK_RSSI, len); >> + SVCMAP(WMI_10_4_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, >> + WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, len); >> } >> >> #undef SVCMAP >> > > Thanks, > Ben
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c index 97548f9..532fc5d 100644 --- a/drivers/net/wireless/ath/ath10k/mac.c +++ b/drivers/net/wireless/ath/ath10k/mac.c @@ -8163,6 +8163,24 @@ void ath10k_mac_destroy(struct ath10k *ar) }, }; +static const struct +ieee80211_iface_combination ath10k_10_4_bcn_int_if_comb[] = { + { + .limits = ath10k_10_4_if_limits, + .n_limits = ARRAY_SIZE(ath10k_10_4_if_limits), + .max_interfaces = 16, + .num_different_channels = 1, + .beacon_int_infra_match = true, + .beacon_int_min_gcd = 100, +#ifdef CONFIG_ATH10K_DFS_CERTIFIED + .radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) | + BIT(NL80211_CHAN_WIDTH_20) | + BIT(NL80211_CHAN_WIDTH_40) | + BIT(NL80211_CHAN_WIDTH_80), +#endif + }, +}; + static void ath10k_get_arvif_iter(void *data, u8 *mac, struct ieee80211_vif *vif) { @@ -8526,6 +8544,13 @@ int ath10k_mac_register(struct ath10k *ar) ar->hw->wiphy->iface_combinations = ath10k_10_4_if_comb; ar->hw->wiphy->n_iface_combinations = ARRAY_SIZE(ath10k_10_4_if_comb); + if (test_bit(WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, + ar->wmi.svc_map)) { + ar->hw->wiphy->iface_combinations = + ath10k_10_4_bcn_int_if_comb; + ar->hw->wiphy->n_iface_combinations = + ARRAY_SIZE(ath10k_10_4_bcn_int_if_comb); + } break; case ATH10K_FW_WMI_OP_VERSION_UNSET: case ATH10K_FW_WMI_OP_VERSION_MAX: diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h index 1562294..126eb17 100644 --- a/drivers/net/wireless/ath/ath10k/wmi.h +++ b/drivers/net/wireless/ath/ath10k/wmi.h @@ -204,6 +204,7 @@ enum wmi_service { WMI_SERVICE_RESET_CHIP, WMI_SERVICE_SPOOF_MAC_SUPPORT, WMI_SERVICE_TX_DATA_ACK_RSSI, + WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, /* keep last */ WMI_SERVICE_MAX, @@ -353,6 +354,11 @@ enum wmi_10_4_service { WMI_10_4_SERVICE_TPC_STATS_FINAL, WMI_10_4_SERVICE_CFR_CAPTURE_SUPPORT, WMI_10_4_SERVICE_TX_DATA_ACK_RSSI, + WMI_10_4_SERVICE_CFR_CAPTURE_IND_MSG_TYPE_LAGACY, + WMI_10_4_SERVICE_PER_PACKET_SW_ENCRYPT, + WMI_10_4_SERVICE_PEER_TID_CONFIGS_SUPPORT, + WMI_10_4_SERVICE_VDEV_BCN_RATE_CONTROL, + WMI_10_4_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, }; static inline char *wmi_service_name(int service_id) @@ -467,6 +473,7 @@ static inline char *wmi_service_name(int service_id) SVCSTR(WMI_SERVICE_TPC_STATS_FINAL); SVCSTR(WMI_SERVICE_RESET_CHIP); SVCSTR(WMI_SERVICE_TX_DATA_ACK_RSSI); + SVCSTR(WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT); default: return NULL; } @@ -777,6 +784,8 @@ static inline void wmi_10_4_svc_map(const __le32 *in, unsigned long *out, WMI_SERVICE_TPC_STATS_FINAL, len); SVCMAP(WMI_10_4_SERVICE_TX_DATA_ACK_RSSI, WMI_SERVICE_TX_DATA_ACK_RSSI, len); + SVCMAP(WMI_10_4_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, + WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, len); } #undef SVCMAP
With the latest firmware design, the beacon interval should be greater than 100 to bring the multiple vaps. Set beacon_int_min_gcd to 100, when the wmi service WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT is enabled in the firmware. If not, beacon_int_min_gcd will be set to the default value 1. Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00015 Tested in QCA9888 with firmware ver 10.4-3.5.1-0005 Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org> --- drivers/net/wireless/ath/ath10k/mac.c | 25 +++++++++++++++++++++++++ drivers/net/wireless/ath/ath10k/wmi.h | 9 +++++++++ 2 files changed, 34 insertions(+)