| Message ID | 20180923063320.8844-1-linus.walleij@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | mmc: sdhci: spear: Use the slot GPIO descriptor | expand |
On 23 September 2018 at 08:33, Linus Walleij <linus.walleij@linaro.org> wrote: > This driver is complicating things for no reason: the "cd" > GPIO can easily be retrieved from the device tree if present > using just mmc_gpiod_request_cd(), which will fetch the > descriptor from the device tree using the standard binding > just fine. > > Cc: Viresh Kumar <vireshk@kernel.org> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Applied for next, thanks! Kind regards Uffe > --- > drivers/mmc/host/sdhci-spear.c | 33 +++++---------------------------- > 1 file changed, 5 insertions(+), 28 deletions(-) > > diff --git a/drivers/mmc/host/sdhci-spear.c b/drivers/mmc/host/sdhci-spear.c > index 9247d51f2eed..916b5b09c3d1 100644 > --- a/drivers/mmc/host/sdhci-spear.c > +++ b/drivers/mmc/host/sdhci-spear.c > @@ -15,13 +15,11 @@ > > #include <linux/clk.h> > #include <linux/delay.h> > -#include <linux/gpio.h> > #include <linux/highmem.h> > #include <linux/module.h> > #include <linux/interrupt.h> > #include <linux/irq.h> > #include <linux/of.h> > -#include <linux/of_gpio.h> > #include <linux/platform_device.h> > #include <linux/pm.h> > #include <linux/slab.h> > @@ -32,7 +30,6 @@ > > struct spear_sdhci { > struct clk *clk; > - int card_int_gpio; > }; > > /* sdhci ops */ > @@ -43,18 +40,6 @@ static const struct sdhci_ops sdhci_pltfm_ops = { > .set_uhs_signaling = sdhci_set_uhs_signaling, > }; > > -static void sdhci_probe_config_dt(struct device_node *np, > - struct spear_sdhci *host) > -{ > - int cd_gpio; > - > - cd_gpio = of_get_named_gpio(np, "cd-gpios", 0); > - if (!gpio_is_valid(cd_gpio)) > - cd_gpio = -1; > - > - host->card_int_gpio = cd_gpio; > -} > - > static int sdhci_probe(struct platform_device *pdev) > { > struct sdhci_host *host; > @@ -109,21 +94,13 @@ static int sdhci_probe(struct platform_device *pdev) > dev_dbg(&pdev->dev, "Error setting desired clk, clk=%lu\n", > clk_get_rate(sdhci->clk)); > > - sdhci_probe_config_dt(pdev->dev.of_node, sdhci); > /* > - * It is optional to use GPIOs for sdhci card detection. If > - * sdhci->card_int_gpio < 0, then use original sdhci lines otherwise > - * GPIO lines. We use the built-in GPIO support for this. > + * It is optional to use GPIOs for sdhci card detection. If we > + * find a descriptor using slot GPIO, we use it. > */ > - if (sdhci->card_int_gpio >= 0) { > - ret = mmc_gpio_request_cd(host->mmc, sdhci->card_int_gpio, 0); > - if (ret < 0) { > - dev_dbg(&pdev->dev, > - "failed to request card-detect gpio%d\n", > - sdhci->card_int_gpio); > - goto disable_clk; > - } > - } > + ret = mmc_gpiod_request_cd(host->mmc, "cd", 0, false, 0, NULL); > + if (ret == -EPROBE_DEFER) > + goto disable_clk; > > ret = sdhci_add_host(host); > if (ret) > -- > 2.17.1 >
diff --git a/drivers/mmc/host/sdhci-spear.c b/drivers/mmc/host/sdhci-spear.c index 9247d51f2eed..916b5b09c3d1 100644 --- a/drivers/mmc/host/sdhci-spear.c +++ b/drivers/mmc/host/sdhci-spear.c @@ -15,13 +15,11 @@ #include <linux/clk.h> #include <linux/delay.h> -#include <linux/gpio.h> #include <linux/highmem.h> #include <linux/module.h> #include <linux/interrupt.h> #include <linux/irq.h> #include <linux/of.h> -#include <linux/of_gpio.h> #include <linux/platform_device.h> #include <linux/pm.h> #include <linux/slab.h> @@ -32,7 +30,6 @@ struct spear_sdhci { struct clk *clk; - int card_int_gpio; }; /* sdhci ops */ @@ -43,18 +40,6 @@ static const struct sdhci_ops sdhci_pltfm_ops = { .set_uhs_signaling = sdhci_set_uhs_signaling, }; -static void sdhci_probe_config_dt(struct device_node *np, - struct spear_sdhci *host) -{ - int cd_gpio; - - cd_gpio = of_get_named_gpio(np, "cd-gpios", 0); - if (!gpio_is_valid(cd_gpio)) - cd_gpio = -1; - - host->card_int_gpio = cd_gpio; -} - static int sdhci_probe(struct platform_device *pdev) { struct sdhci_host *host; @@ -109,21 +94,13 @@ static int sdhci_probe(struct platform_device *pdev) dev_dbg(&pdev->dev, "Error setting desired clk, clk=%lu\n", clk_get_rate(sdhci->clk)); - sdhci_probe_config_dt(pdev->dev.of_node, sdhci); /* - * It is optional to use GPIOs for sdhci card detection. If - * sdhci->card_int_gpio < 0, then use original sdhci lines otherwise - * GPIO lines. We use the built-in GPIO support for this. + * It is optional to use GPIOs for sdhci card detection. If we + * find a descriptor using slot GPIO, we use it. */ - if (sdhci->card_int_gpio >= 0) { - ret = mmc_gpio_request_cd(host->mmc, sdhci->card_int_gpio, 0); - if (ret < 0) { - dev_dbg(&pdev->dev, - "failed to request card-detect gpio%d\n", - sdhci->card_int_gpio); - goto disable_clk; - } - } + ret = mmc_gpiod_request_cd(host->mmc, "cd", 0, false, 0, NULL); + if (ret == -EPROBE_DEFER) + goto disable_clk; ret = sdhci_add_host(host); if (ret)
This driver is complicating things for no reason: the "cd" GPIO can easily be retrieved from the device tree if present using just mmc_gpiod_request_cd(), which will fetch the descriptor from the device tree using the standard binding just fine. Cc: Viresh Kumar <vireshk@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- drivers/mmc/host/sdhci-spear.c | 33 +++++---------------------------- 1 file changed, 5 insertions(+), 28 deletions(-)