@@ -764,8 +764,15 @@ config LEDS_LM3697
This supports the LED device LM3697.
config LEDS_LM3633
- tristate "LED driver for LM3633"
+ tristate "LED driver for LM3632"
depends on LEDS_TI_LMU_COMMON
+ help
+ Say Y to enable the LED driver for TI LMU devices.
+ This supports the LED device LM3632.
+
+config LEDS_LM3632
+ tristate "LED driver for LM3632"
+ depends on LEDS_TI_LMU_COMMON
help
Say Y to enable the LED driver for TI LMU devices.
This supports the LED device LM3633.
@@ -79,6 +79,7 @@ obj-$(CONFIG_LEDS_LM3692X) += leds-lm3692x.o
obj-$(CONFIG_LEDS_SC27XX_BLTC) += leds-sc27xx-bltc.o
obj-$(CONFIG_LEDS_LM3601X) += leds-lm3601x.o
obj-$(CONFIG_LEDS_LM3697) += leds-lm3697.o
+obj-$(CONFIG_LEDS_LM3632) += leds-lm3632.o
obj-$(CONFIG_LEDS_LM3633) += leds-lm3633.o
obj-$(CONFIG_LEDS_TI_LMU_COMMON) += ti-lmu-led-common.o
new file mode 100644
@@ -0,0 +1,547 @@
+// SPDX-License-Identifier: GPL-2.0
+// Flash and torch driver for Texas Instruments LM3632 LED
+// Flash driver chip family
+// Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/
+
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/led-class-flash.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <uapi/linux/uleds.h>
+
+#include "ti-lmu-led-common.h"
+
+#define LM3632_MODE_BL 0x0
+#define LM3632_MODE_TORCH 0x1
+
+/* Registers */
+#define LM3632_REV_REG 0x01
+#define LM3632_CFG1_REG 0x02
+#define LM3632_CFG2_REG 0x03
+#define LM3633_BL_BRT_LSB 0x04
+#define LM3633_BL_BRT_MSB 0x05
+#define LM3632_FLASH_TORCH_BRT 0x06
+#define LM3632_FLASH_CFG 0x07
+#define LM3632_ENABLE_REG 0x0a
+#define LM3632_FLAGS1_REG 0x0b
+#define LM3632_FLAGS2_REG 0x10
+
+/* Enable Mode bits */
+#define LM3632_BL_EN BIT(0)
+#define LM3632_STROBE_EN BIT(1)
+#define LM3632_FLASH_MODE BIT(2)
+#define LM3632_BLED1_2_EN BIT(3)
+#define LM3632_BLED1_EN BIT(4)
+#define LM3632_BL_OVP_EN BIT(6)
+#define LM3632_SW_RESET BIT(7)
+
+/* Flags 1 Mask */
+#define LM3632_THERM_SHUTDOWN BIT(0)
+#define LM3632_FLASH_TIME_OUT BIT(1)
+#define LM3632_FLED_SHORT_FAULT BIT(2)
+#define LM3632_VINM_SHORT_FAULT BIT(4)
+#define LM3632_FOUT_SHORT_FAULT BIT(5)
+#define LM3632_FLASH_OVP_FAULT BIT(6)
+#define LM3632_BL_OVP_FAULT BIT(7)
+
+/* Flags 2 Mask */
+#define LM3632_BL_OCP_FAULT BIT(0)
+#define LM3632_FLASH_OCP_FAULT BIT(1)
+#define LM3632_VNEG_SHORT_FAULT BIT(2)
+#define LM3632_VPOS_SHORT_FAULT BIT(3)
+#define LM3632_VNEG_OVP_FAULT BIT(4)
+#define LM3632_LCM_OVP_FAULT BIT(5)
+
+#define LM3632_TORCH_BRT_SHIFT 4
+#define LM3632_STROBE_REG_DIV 16
+#define LM3632_STROBE_STEP_UA 100000
+
+#define LM3632_MAX_TORCH_I_UA 375000
+#define LM3632_MIN_TORCH_I_UA 2500
+
+#define LM3632_MAX_STROBE_I_UA 1500000
+#define LM3632_MIN_STROBE_I_UA 10000
+
+#define LM3632_TIMEOUT_MASK 0x1e
+#define LM3632_ENABLE_MASK (LM3632_BL_EN | LM3632_STROBE_EN)
+
+#define LM3632_TIMEOUT_STEP_US 32000
+#define LM3632_MIN_TIMEOUT_US 32000
+#define LM3632_MAX_TIMEOUT_US 1024000
+
+#define LM3632_TORCH_BRT_MASK 0x0f
+#define LM3632_FLASH_BRT_MASK 0xf0
+
+/**
+ * struct lm3632_led -
+ * @fled_cdev: flash LED class device pointer
+ * @led_name - LED label
+ * @led_dev - LED class device
+ * @priv - Pointer to the lm3632 struct
+ * @lmu_data - Register and setting values for common code
+ * @led_name: LED label for the Torch or IR LED
+ * @flash_timeout: the timeout for the flash
+ * @last_flag: last known flags register value
+ * @torch_current_max: maximum current for the torch
+ * @flash_current_max: maximum current for the flash
+ * @max_flash_timeout: maximum timeout for the flash
+ */
+struct lm3632_led {
+ struct led_classdev_flash fled_cdev;
+ char led_name[LED_MAX_NAME_SIZE];
+ struct led_classdev led_dev;
+ struct ti_lmu_bank lmu_data;
+ struct lm3632 *priv;
+
+ unsigned int flash_timeout;
+ unsigned int last_flag;
+
+ u32 torch_current_max;
+ u32 flash_current_max;
+ u32 max_flash_timeout;
+};
+
+/**
+ * struct lm3632 -
+ * @client: Pointer to the I2C client
+ * @regmap: Devices register map
+ * @lock: Lock for reading/writing the device
+ * @leds - Array of LED strings
+ */
+struct lm3632 {
+ struct i2c_client *client;
+ struct regmap *regmap;
+ struct device *dev;
+ struct mutex lock;
+
+ struct lm3632_led leds[];
+};
+
+static const struct reg_default lm3632_regmap_defs[] = {
+ { LM3632_CFG1_REG, 0x30 },
+ { LM3632_CFG2_REG, 0x0d },
+ { LM3632_FLASH_CFG, 0x2f },
+ { LM3632_ENABLE_REG, 0x00 },
+};
+
+static bool lm3632_volatile_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case LM3632_FLAGS1_REG:
+ case LM3632_FLAGS2_REG:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static const struct regmap_config lm3632_regmap = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = LM3632_FLAGS2_REG,
+ .reg_defaults = lm3632_regmap_defs,
+ .num_reg_defaults = ARRAY_SIZE(lm3632_regmap_defs),
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_reg = lm3632_volatile_reg,
+};
+
+static struct lm3632_led *fled_cdev_to_led(struct led_classdev_flash *fled_cdev)
+{
+ return container_of(fled_cdev, struct lm3632_led, fled_cdev);
+}
+
+static int lm3632_read_faults(struct lm3632_led *led)
+{
+ struct lm3632 *priv = led->priv;
+ int flags_val;
+ int ret;
+
+ ret = regmap_read(priv->regmap, LM3632_FLAGS1_REG, &flags_val);
+ if (ret < 0)
+ return -EIO;
+
+ led->last_flag = 0;
+
+ if (flags_val & LM3632_FLASH_OVP_FAULT)
+ led->last_flag |= LED_FAULT_OVER_VOLTAGE;
+
+ if (flags_val & LM3632_THERM_SHUTDOWN)
+ led->last_flag |= LED_FAULT_OVER_TEMPERATURE;
+
+ if (flags_val & (LM3632_FLED_SHORT_FAULT | LM3632_VINM_SHORT_FAULT |
+ LM3632_FOUT_SHORT_FAULT))
+ led->last_flag |= LED_FAULT_SHORT_CIRCUIT;
+
+ if (flags_val & LM3632_THERM_SHUTDOWN)
+ led->last_flag |= LED_FAULT_LED_OVER_TEMPERATURE;
+
+ if (flags_val & LM3632_FLASH_TIME_OUT)
+ led->last_flag |= LED_FAULT_TIMEOUT;
+
+ ret = regmap_read(priv->regmap, LM3632_FLAGS2_REG, &flags_val);
+ if (ret < 0)
+ return -EIO;
+
+ if (flags_val & (LM3632_BL_OCP_FAULT | LM3632_FLASH_OCP_FAULT))
+ led->last_flag |= LED_FAULT_OVER_CURRENT;
+
+ if (flags_val & LM3632_FLASH_OCP_FAULT)
+ led->last_flag |= LED_FAULT_OVER_CURRENT;
+
+ return led->last_flag;
+}
+
+static int lm3632_backlight_brightness_set(struct led_classdev *cdev,
+ enum led_brightness brightness)
+{
+ struct lm3632_led *led = container_of(cdev, struct lm3632_led,
+ led_dev);
+ struct lm3632 *priv = led->priv;
+ int ret;
+
+ mutex_lock(&priv->lock);
+
+ ret = ti_lmu_common_set_brightness(&led->lmu_data, brightness);
+ if (ret)
+ dev_err(&priv->client->dev, "Cannot write brightness\n");
+
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static int lm3632_strobe_flash_brightness_set(struct lm3632_led *led,
+ u8 brightness_val)
+{
+ struct lm3632 *priv = led->priv;
+ int ret;
+
+ if (brightness_val == LED_OFF) {
+ ret = regmap_update_bits(priv->regmap, LM3632_ENABLE_REG,
+ LM3632_STROBE_EN, LED_OFF);
+ return ret;
+ }
+
+ ret = regmap_update_bits(priv->regmap, LM3632_FLASH_TORCH_BRT,
+ LM3632_TORCH_BRT_MASK, brightness_val);
+ if (ret < 0)
+ return ret;
+
+ return regmap_update_bits(priv->regmap, LM3632_ENABLE_REG,
+ LM3632_STROBE_EN,
+ LM3632_STROBE_EN);
+}
+
+static int lm3632_torch_brightness_set(struct led_classdev *cdev,
+ enum led_brightness brightness)
+{
+ struct led_classdev_flash *fled_cdev = lcdev_to_flcdev(cdev);
+ struct lm3632_led *led = fled_cdev_to_led(fled_cdev);
+ struct lm3632 *priv = led->priv;
+ int ret, brightness_val;
+
+ mutex_lock(&priv->lock);
+
+ ret = lm3632_read_faults(led);
+ if (ret < 0)
+ goto out;
+
+ brightness_val = (brightness / 16);
+
+ ret = lm3632_strobe_flash_brightness_set(led, brightness_val);
+
+out:
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static int lm3632_strobe_set(struct led_classdev_flash *fled_cdev,
+ bool state)
+{
+ struct lm3632_led *led = fled_cdev_to_led(fled_cdev);
+ struct lm3632 *priv = led->priv;
+ int timeout_reg_val;
+ int current_timeout;
+ int ret;
+
+ mutex_lock(&priv->lock);
+
+ ret = regmap_read(priv->regmap, LM3632_FLASH_CFG, ¤t_timeout);
+ if (ret < 0)
+ goto out;
+
+ if (led->flash_timeout != current_timeout)
+ ret = regmap_update_bits(priv->regmap, LM3632_FLASH_CFG,
+ LM3632_TIMEOUT_MASK, timeout_reg_val);
+
+ if (state)
+ ret = regmap_update_bits(priv->regmap, LM3632_ENABLE_REG,
+ LM3632_STROBE_EN, LM3632_STROBE_EN);
+ else
+ ret = regmap_update_bits(priv->regmap, LM3632_ENABLE_REG,
+ LM3632_STROBE_EN, LED_OFF);
+
+ ret = lm3632_read_faults(led);
+out:
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static int lm3632_flash_brightness_set(struct led_classdev_flash *fled_cdev,
+ u32 brightness)
+{
+ struct lm3632_led *led = fled_cdev_to_led(fled_cdev);
+ struct lm3632 *priv = led->priv;
+ u8 brightness_val;
+ int ret;
+
+ mutex_lock(&priv->lock);
+ ret = lm3632_read_faults(led);
+ if (ret < 0)
+ goto out;
+
+ brightness_val = (brightness / 16) << LM3632_TORCH_BRT_SHIFT;
+
+ ret = lm3632_strobe_flash_brightness_set(led, brightness_val);
+out:
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static int lm3632_flash_timeout_set(struct led_classdev_flash *fled_cdev,
+ u32 timeout)
+{
+ struct lm3632_led *led = fled_cdev_to_led(fled_cdev);
+ struct lm3632 *priv = led->priv;
+
+ mutex_lock(&priv->lock);
+
+ led->flash_timeout = timeout;
+
+ mutex_unlock(&priv->lock);
+
+ return 0;
+}
+
+static int lm3632_strobe_get(struct led_classdev_flash *fled_cdev, bool *state)
+{
+ struct lm3632_led *led = fled_cdev_to_led(fled_cdev);
+ struct lm3632 *priv = led->priv;
+ int strobe_state;
+ int ret;
+
+ mutex_lock(&priv->lock);
+
+ ret = regmap_read(priv->regmap, LM3632_ENABLE_REG, &strobe_state);
+ if (ret < 0)
+ goto out;
+
+ *state = strobe_state & LM3632_STROBE_EN;
+
+out:
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static int lm3632_flash_fault_get(struct led_classdev_flash *fled_cdev,
+ u32 *fault)
+{
+ struct lm3632_led *led = fled_cdev_to_led(fled_cdev);
+
+ lm3632_read_faults(led);
+
+ *fault = led->last_flag;
+
+ return 0;
+}
+
+static const struct led_flash_ops flash_ops = {
+ .flash_brightness_set = lm3632_flash_brightness_set,
+ .strobe_set = lm3632_strobe_set,
+ .strobe_get = lm3632_strobe_get,
+ .timeout_set = lm3632_flash_timeout_set,
+ .fault_get = lm3632_flash_fault_get,
+};
+
+static int lm3632_register_strobe_leds(struct lm3632_led *led)
+{
+ struct led_classdev *led_cdev;
+ struct led_flash_setting *setting;
+
+ led->fled_cdev.ops = &flash_ops;
+
+ setting = &led->fled_cdev.timeout;
+ setting->min = LM3632_MIN_TIMEOUT_US;
+ setting->max = led->max_flash_timeout;
+ setting->step = LM3632_TIMEOUT_STEP_US;
+ setting->val = led->max_flash_timeout;
+
+ setting = &led->fled_cdev.brightness;
+ setting->min = LM3632_MIN_STROBE_I_UA;
+ setting->max = led->flash_current_max;
+ setting->step = LM3632_STROBE_STEP_UA;
+ setting->val = led->flash_current_max;
+
+ led_cdev = &led->fled_cdev.led_cdev;
+ led_cdev->name = led->led_name;
+ led_cdev->brightness_set_blocking = lm3632_torch_brightness_set;
+ led_cdev->max_brightness = led->torch_current_max;
+
+ led_cdev->flags |= LED_DEV_CAP_FLASH;
+
+ return led_classdev_flash_register(&led->priv->client->dev, &led->fled_cdev);
+}
+
+static int lm3632_parse_node(struct lm3632 *priv)
+{
+ struct fwnode_handle *child = NULL;
+ struct lm3632_led *led;
+ int ret = -ENODEV;
+ const char *name;
+ u32 led_mode;
+ int i;
+
+ device_for_each_child_node(priv->dev, child) {
+ ret = fwnode_property_read_u32(child, "reg", &led_mode);
+ if (ret) {
+ dev_err(&priv->client->dev, "reg DT property missing\n");
+ goto out_err;
+ }
+
+ if (led_mode < LM3632_MODE_TORCH ||
+ led_mode > LM3632_MODE_BL) {
+ dev_warn(&priv->client->dev, "Invalid led mode requested\n");
+ ret = -EINVAL;
+ goto out_err;
+ }
+
+ led = &priv->leds[i];
+ led->priv = priv;
+
+ ret = fwnode_property_read_string(child, "label", &name);
+ if (ret) {
+ if (led_mode == LM3632_MODE_TORCH)
+ name = "torch";
+ else
+ name = "backlight";
+ }
+
+ snprintf(led->led_name, sizeof(led->led_name),
+ "%s:%s", priv->client->name, name);
+
+ if (led_mode == LM3632_MODE_TORCH) {
+ ret = fwnode_property_read_u32(child, "led-max-microamp",
+ &led->torch_current_max);
+ if (ret) {
+ dev_warn(&priv->client->dev,
+ "led-max-microamp DT property missing\n");
+ goto out_err;
+ }
+
+ ret = fwnode_property_read_u32(child, "flash-max-microamp",
+ &led->flash_current_max);
+ if (ret) {
+ dev_warn(&priv->client->dev,
+ "flash-max-microamp DT property missing\n");
+ goto out_err;
+ }
+
+ ret = fwnode_property_read_u32(child, "flash-max-timeout-us",
+ &led->max_flash_timeout);
+ if (ret) {
+ dev_warn(&priv->client->dev,
+ "flash-max-timeout-us DT property missing\n");
+ goto out_err;
+ }
+
+ ret = lm3632_register_strobe_leds(led);
+ if (ret) {
+ dev_warn(&priv->client->dev,
+ "Failed to register flash LEDs\n");
+ goto out_err;
+ }
+
+ } else {
+ led->led_dev.name = led->led_name;
+ led->led_dev.brightness_set_blocking = lm3632_backlight_brightness_set;
+ led->lmu_data.regmap = priv->regmap;
+ led->lmu_data.max_brightness = MAX_BRIGHTNESS_11BIT;
+ led->lmu_data.lsb_brightness_reg = LM3633_BL_BRT_LSB;
+ led->lmu_data.msb_brightness_reg = LM3633_BL_BRT_MSB;
+
+ ret = devm_led_classdev_register(priv->dev, &led->led_dev);
+ }
+
+ i++;
+ }
+out_err:
+ fwnode_handle_put(child);
+ return ret;
+}
+
+static int lm3632_probe(struct i2c_client *client)
+{
+ struct lm3632 *led;
+ int ret;
+
+ led = devm_kzalloc(&client->dev, sizeof(*led), GFP_KERNEL);
+ if (!led)
+ return -ENOMEM;
+
+ led->client = client;
+ led->dev = &client->dev;
+ i2c_set_clientdata(client, led);
+
+ led->regmap = devm_regmap_init_i2c(client, &lm3632_regmap);
+ if (IS_ERR(led->regmap)) {
+ ret = PTR_ERR(led->regmap);
+ dev_err(&client->dev,
+ "Failed to allocate register map: %d\n", ret);
+ return ret;
+ }
+
+ mutex_init(&led->lock);
+
+ return lm3632_parse_node(led);
+}
+
+static int lm3632_remove(struct i2c_client *client)
+{
+ struct lm3632 *led = i2c_get_clientdata(client);
+
+/* led_classdev_flash_unregister(&led->fled_cdev);*/
+ mutex_destroy(&led->lock);
+
+ return regmap_update_bits(led->regmap, LM3632_ENABLE_REG,
+ LM3632_ENABLE_MASK, 0x00);
+}
+
+static const struct i2c_device_id lm3632_id[] = {
+ { "LM3632", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, lm3632_id);
+
+static const struct of_device_id of_lm3632_leds_match[] = {
+ { .compatible = "ti,lm3632", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, of_lm3632_leds_match);
+
+static struct i2c_driver lm3632_i2c_driver = {
+ .driver = {
+ .name = "lm3632",
+ .of_match_table = of_lm3632_leds_match,
+ },
+ .probe_new = lm3632_probe,
+ .remove = lm3632_remove,
+ .id_table = lm3632_id,
+};
+module_i2c_driver(lm3632_i2c_driver);
+
+MODULE_DESCRIPTION("Texas Instruments Flash Lighting driver for LM3632");
+MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
+MODULE_LICENSE("GPL v2");
Add the dedicated TI LM3632 LED driver. This LED device is capable of driving a backlight display. In addition to the backlight the device has control of a strobe and torch output. Data sheet: http://www.ti.com/lit/ds/symlink/lm3632a.pdf Signed-off-by: Dan Murphy <dmurphy@ti.com> --- drivers/leds/Kconfig | 9 +- drivers/leds/Makefile | 1 + drivers/leds/leds-lm3632.c | 547 +++++++++++++++++++++++++++++++++++++ 3 files changed, 556 insertions(+), 1 deletion(-) create mode 100644 drivers/leds/leds-lm3632.c