diff mbox series

ASoC: nau8822: new codec driver

Message ID 20180928031002.16112-1-CTLIN0@nuvoton.com (mailing list archive)
State Accepted
Commit 1e3cb6c321be2e5295dcaa94c2bf42a43a47a067
Headers show
Series ASoC: nau8822: new codec driver | expand

Commit Message

David Lin Sept. 28, 2018, 3:10 a.m. UTC
Add driver for NAU88C22.

Signed-off-by: David Lin <CTLIN0@nuvoton.com>
---
 .../devicetree/bindings/sound/nau8822.txt     |   16 +
 sound/soc/codecs/Kconfig                      |    5 +
 sound/soc/codecs/Makefile                     |    2 +
 sound/soc/codecs/nau8822.c                    | 1136 +++++++++++++++++
 sound/soc/codecs/nau8822.h                    |  204 +++
 5 files changed, 1363 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/nau8822.txt
 create mode 100644 sound/soc/codecs/nau8822.c
 create mode 100644 sound/soc/codecs/nau8822.h

Comments

Mark Brown Oct. 17, 2018, 6:54 p.m. UTC | #1
On Fri, Sep 28, 2018 at 11:10:04AM +0800, David Lin wrote:

This looks mostly good so I'm going to apply it, I do have a couple of
comments below but they are quite small and I think they can be
addressed with followup patches.

> +++ b/sound/soc/codecs/nau8822.c
> @@ -0,0 +1,1136 @@
> +/*
> + * nau8822.c  --  NAU8822 ALSA Soc Audio Codec driver
> + *
> + * Copyright 2017 Nuvoton Technology Corp.
> + *
> + * Author: David Lin <ctlin0@nuvoton.com>
> + * Co-author: John Hsu <kchsu0@nuvoton.com>
> + * Co-author: Seven Li <wtli@nuvoton.com>
> + *
> + * Based on WM8974.c
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */

This should be converted to use a SPDX license header

	// SPDX-License-Identifier: GPL-2.0.

> +static int nau8822_config_clkdiv(struct snd_soc_dai *dai, int div, int rate)
> +{
> +	struct snd_soc_component *component = dai->component;
> +	struct nau8822 *nau8822 = snd_soc_component_get_drvdata(component);
> +	struct nau8822_pll *pll = &nau8822->pll;
> +	int i, sclk, imclk;

We're trying to get away from using set_clkdiv() as it makes it much
harder to use generic card drivers without specific knowledge of the 
card.  However in this case it seems like it's mainly choosing if we
should use the MCLK directly or the PLL and you should be able to do
everything in the set_sysclk() operation - is there a reason not to do
that?  If not then moving to set_sysclk() would avoid problems.
David Lin Oct. 19, 2018, 4:56 a.m. UTC | #2
On 10/18/2018 2:54 AM, Mark Brown wrote:
> On Fri, Sep 28, 2018 at 11:10:04AM +0800, David Lin wrote:
>
> This looks mostly good so I'm going to apply it, I do have a couple of
> comments below but they are quite small and I think they can be
> addressed with followup patches.
>
>> +++ b/sound/soc/codecs/nau8822.c
>> @@ -0,0 +1,1136 @@
>> +/*
>> + * nau8822.c  --  NAU8822 ALSA Soc Audio Codec driver
>> + *
>> + * Copyright 2017 Nuvoton Technology Corp.
>> + *
>> + * Author: David Lin <ctlin0@nuvoton.com>
>> + * Co-author: John Hsu <kchsu0@nuvoton.com>
>> + * Co-author: Seven Li <wtli@nuvoton.com>
>> + *
>> + * Based on WM8974.c
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
> This should be converted to use a SPDX license header
>
>       // SPDX-License-Identifier: GPL-2.0.
OK, I will convert it on next patch.
>> +static int nau8822_config_clkdiv(struct snd_soc_dai *dai, int div, int rate)
>> +{
>> +    struct snd_soc_component *component = dai->component;
>> +    struct nau8822 *nau8822 = snd_soc_component_get_drvdata(component);
>> +    struct nau8822_pll *pll = &nau8822->pll;
>> +    int i, sclk, imclk;
> We're trying to get away from using set_clkdiv() as it makes it much
> harder to use generic card drivers without specific knowledge of the
> card.  However in this case it seems like it's mainly choosing if we
> should use the MCLK directly or the PLL and you should be able to do
> everything in the set_sysclk() operation - is there a reason not to do
> that?  If not then moving to set_sysclk() would avoid problems.

The nau8822_config_clkdiv() will be called internally by
nau8822_hw_params(), not link to the function point (*set_clkdiv) from
the structure "snd_soc_dai_ops".

If nau8822_config_clkdiv() need to simplify, I will remove case
NAU8822_CLK_PLL. The reason is using set_pll() operation can also finish
clk configure from machine driver.



===========================================================================================
The privileged confidential information contained in this email is intended for use only by the addressees as indicated by the original sender of this email. If you are not the addressee indicated in this email or are not responsible for delivery of the email to such a person, please kindly reply to the sender indicating this fact and delete all copies of it from your computer and network server immediately. Your cooperation is highly appreciated. It is advised that any unauthorized use of confidential information of Nuvoton is strictly prohibited; and any information in this email irrelevant to the official business of Nuvoton shall be deemed as neither given nor endorsed by Nuvoton.
Mark Brown Oct. 19, 2018, 10 a.m. UTC | #3
On Fri, Oct 19, 2018 at 12:56:53PM +0800, AC30 CTLin0 wrote:
> On 10/18/2018 2:54 AM, Mark Brown wrote:
> > On Fri, Sep 28, 2018 at 11:10:04AM +0800, David Lin wrote:

> > We're trying to get away from using set_clkdiv() as it makes it much
> > harder to use generic card drivers without specific knowledge of the
> > card.  However in this case it seems like it's mainly choosing if we
> > should use the MCLK directly or the PLL and you should be able to do
> > everything in the set_sysclk() operation - is there a reason not to do
> > that?  If not then moving to set_sysclk() would avoid problems.

> The nau8822_config_clkdiv() will be called internally by
> nau8822_hw_params(), not link to the function point (*set_clkdiv) from
> the structure "snd_soc_dai_ops".

> If nau8822_config_clkdiv() need to simplify, I will remove case
> NAU8822_CLK_PLL. The reason is using set_pll() operation can also finish
> clk configure from machine driver.

Ah, sorry - now that you mention it I think I did see that it wasn't
referenced as an actual op when I looked at a previous version which is
why I didn't mention it then.  The current code is fine, don't worry
about it.
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/sound/nau8822.txt b/Documentation/devicetree/bindings/sound/nau8822.txt
new file mode 100644
index 000000000000..a471d162d4e5
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/nau8822.txt
@@ -0,0 +1,16 @@ 
+NAU8822 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "nuvoton,nau8822"
+
+  - reg : the I2C address of the device.
+
+Example:
+
+codec: nau8822@1a {
+	compatible = "nuvoton,nau8822";
+	reg = <0x1a>;
+};
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index efb095dbcd71..57365dbc1581 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -109,6 +109,7 @@  config SND_SOC_ALL_CODECS
 	select SND_SOC_MT6351 if MTK_PMIC_WRAP
 	select SND_SOC_NAU8540 if I2C
 	select SND_SOC_NAU8810 if I2C
+	select SND_SOC_NAU8822 if I2C
 	select SND_SOC_NAU8824 if I2C
 	select SND_SOC_NAU8825 if I2C
 	select SND_SOC_HDMI_CODEC
@@ -1299,6 +1300,10 @@  config SND_SOC_NAU8810
 	tristate "Nuvoton Technology Corporation NAU88C10 CODEC"
 	depends on I2C
 
+config SND_SOC_NAU8822
+	tristate "Nuvoton Technology Corporation NAU88C22 CODEC"
+	depends on I2C
+
 config SND_SOC_NAU8824
 	tristate "Nuvoton Technology Corporation NAU88L24 CODEC"
 	depends on I2C
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile
index 7ae7c85e8219..181a7d222fd7 100644
--- a/sound/soc/codecs/Makefile
+++ b/sound/soc/codecs/Makefile
@@ -106,6 +106,7 @@  snd-soc-msm8916-digital-objs := msm8916-wcd-digital.o
 snd-soc-mt6351-objs := mt6351.o
 snd-soc-nau8540-objs := nau8540.o
 snd-soc-nau8810-objs := nau8810.o
+snd-soc-nau8822-objs := nau8822.o
 snd-soc-nau8824-objs := nau8824.o
 snd-soc-nau8825-objs := nau8825.o
 snd-soc-hdmi-codec-objs := hdmi-codec.o
@@ -366,6 +367,7 @@  obj-$(CONFIG_SND_SOC_MSM8916_WCD_DIGITAL) +=snd-soc-msm8916-digital.o
 obj-$(CONFIG_SND_SOC_MT6351)	+= snd-soc-mt6351.o
 obj-$(CONFIG_SND_SOC_NAU8540)   += snd-soc-nau8540.o
 obj-$(CONFIG_SND_SOC_NAU8810)   += snd-soc-nau8810.o
+obj-$(CONFIG_SND_SOC_NAU8822)   += snd-soc-nau8822.o
 obj-$(CONFIG_SND_SOC_NAU8824)   += snd-soc-nau8824.o
 obj-$(CONFIG_SND_SOC_NAU8825)   += snd-soc-nau8825.o
 obj-$(CONFIG_SND_SOC_HDMI_CODEC)	+= snd-soc-hdmi-codec.o
diff --git a/sound/soc/codecs/nau8822.c b/sound/soc/codecs/nau8822.c
new file mode 100644
index 000000000000..622ce947f134
--- /dev/null
+++ b/sound/soc/codecs/nau8822.c
@@ -0,0 +1,1136 @@ 
+/*
+ * nau8822.c  --  NAU8822 ALSA Soc Audio Codec driver
+ *
+ * Copyright 2017 Nuvoton Technology Corp.
+ *
+ * Author: David Lin <ctlin0@nuvoton.com>
+ * Co-author: John Hsu <kchsu0@nuvoton.com>
+ * Co-author: Seven Li <wtli@nuvoton.com>
+ *
+ * Based on WM8974.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/pm.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/initval.h>
+#include <sound/tlv.h>
+#include <asm/div64.h>
+#include "nau8822.h"
+
+#define NAU_PLL_FREQ_MAX 100000000
+#define NAU_PLL_FREQ_MIN 90000000
+#define NAU_PLL_REF_MAX 33000000
+#define NAU_PLL_REF_MIN 8000000
+#define NAU_PLL_OPTOP_MIN 6
+
+static const int nau8822_mclk_scaler[] = { 10, 15, 20, 30, 40, 60, 80, 120 };
+
+static const struct reg_default nau8822_reg_defaults[] = {
+	{ NAU8822_REG_POWER_MANAGEMENT_1, 0x0000 },
+	{ NAU8822_REG_POWER_MANAGEMENT_2, 0x0000 },
+	{ NAU8822_REG_POWER_MANAGEMENT_3, 0x0000 },
+	{ NAU8822_REG_AUDIO_INTERFACE, 0x0050 },
+	{ NAU8822_REG_COMPANDING_CONTROL, 0x0000 },
+	{ NAU8822_REG_CLOCKING, 0x0140 },
+	{ NAU8822_REG_ADDITIONAL_CONTROL, 0x0000 },
+	{ NAU8822_REG_GPIO_CONTROL, 0x0000 },
+	{ NAU8822_REG_JACK_DETECT_CONTROL_1, 0x0000 },
+	{ NAU8822_REG_DAC_CONTROL, 0x0000 },
+	{ NAU8822_REG_LEFT_DAC_DIGITAL_VOLUME, 0x00ff },
+	{ NAU8822_REG_RIGHT_DAC_DIGITAL_VOLUME, 0x00ff },
+	{ NAU8822_REG_JACK_DETECT_CONTROL_2, 0x0000 },
+	{ NAU8822_REG_ADC_CONTROL, 0x0100 },
+	{ NAU8822_REG_LEFT_ADC_DIGITAL_VOLUME, 0x00ff },
+	{ NAU8822_REG_RIGHT_ADC_DIGITAL_VOLUME, 0x00ff },
+	{ NAU8822_REG_EQ1, 0x012c },
+	{ NAU8822_REG_EQ2, 0x002c },
+	{ NAU8822_REG_EQ3, 0x002c },
+	{ NAU8822_REG_EQ4, 0x002c },
+	{ NAU8822_REG_EQ5, 0x002c },
+	{ NAU8822_REG_DAC_LIMITER_1, 0x0032 },
+	{ NAU8822_REG_DAC_LIMITER_2, 0x0000 },
+	{ NAU8822_REG_NOTCH_FILTER_1, 0x0000 },
+	{ NAU8822_REG_NOTCH_FILTER_2, 0x0000 },
+	{ NAU8822_REG_NOTCH_FILTER_3, 0x0000 },
+	{ NAU8822_REG_NOTCH_FILTER_4, 0x0000 },
+	{ NAU8822_REG_ALC_CONTROL_1, 0x0038 },
+	{ NAU8822_REG_ALC_CONTROL_2, 0x000b },
+	{ NAU8822_REG_ALC_CONTROL_3, 0x0032 },
+	{ NAU8822_REG_NOISE_GATE, 0x0010 },
+	{ NAU8822_REG_PLL_N, 0x0008 },
+	{ NAU8822_REG_PLL_K1, 0x000c },
+	{ NAU8822_REG_PLL_K2, 0x0093 },
+	{ NAU8822_REG_PLL_K3, 0x00e9 },
+	{ NAU8822_REG_3D_CONTROL, 0x0000 },
+	{ NAU8822_REG_RIGHT_SPEAKER_CONTROL, 0x0000 },
+	{ NAU8822_REG_INPUT_CONTROL, 0x0033 },
+	{ NAU8822_REG_LEFT_INP_PGA_CONTROL, 0x0010 },
+	{ NAU8822_REG_RIGHT_INP_PGA_CONTROL, 0x0010 },
+	{ NAU8822_REG_LEFT_ADC_BOOST_CONTROL, 0x0100 },
+	{ NAU8822_REG_RIGHT_ADC_BOOST_CONTROL, 0x0100 },
+	{ NAU8822_REG_OUTPUT_CONTROL, 0x0002 },
+	{ NAU8822_REG_LEFT_MIXER_CONTROL, 0x0001 },
+	{ NAU8822_REG_RIGHT_MIXER_CONTROL, 0x0001 },
+	{ NAU8822_REG_LHP_VOLUME, 0x0039 },
+	{ NAU8822_REG_RHP_VOLUME, 0x0039 },
+	{ NAU8822_REG_LSPKOUT_VOLUME, 0x0039 },
+	{ NAU8822_REG_RSPKOUT_VOLUME, 0x0039 },
+	{ NAU8822_REG_AUX2_MIXER, 0x0001 },
+	{ NAU8822_REG_AUX1_MIXER, 0x0001 },
+	{ NAU8822_REG_POWER_MANAGEMENT_4, 0x0000 },
+	{ NAU8822_REG_LEFT_TIME_SLOT, 0x0000 },
+	{ NAU8822_REG_MISC, 0x0020 },
+	{ NAU8822_REG_RIGHT_TIME_SLOT, 0x0000 },
+	{ NAU8822_REG_DEVICE_REVISION, 0x007f },
+	{ NAU8822_REG_DEVICE_ID, 0x001a },
+	{ NAU8822_REG_DAC_DITHER, 0x0114 },
+	{ NAU8822_REG_ALC_ENHANCE_1, 0x0000 },
+	{ NAU8822_REG_ALC_ENHANCE_2, 0x0000 },
+	{ NAU8822_REG_192KHZ_SAMPLING, 0x0008 },
+	{ NAU8822_REG_MISC_CONTROL, 0x0000 },
+	{ NAU8822_REG_INPUT_TIEOFF, 0x0000 },
+	{ NAU8822_REG_POWER_REDUCTION, 0x0000 },
+	{ NAU8822_REG_AGC_PEAK2PEAK, 0x0000 },
+	{ NAU8822_REG_AGC_PEAK_DETECT, 0x0000 },
+	{ NAU8822_REG_AUTOMUTE_CONTROL, 0x0000 },
+	{ NAU8822_REG_OUTPUT_TIEOFF, 0x0000 },
+};
+
+static bool nau8822_readable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case NAU8822_REG_RESET ... NAU8822_REG_JACK_DETECT_CONTROL_1:
+	case NAU8822_REG_DAC_CONTROL ... NAU8822_REG_LEFT_ADC_DIGITAL_VOLUME:
+	case NAU8822_REG_RIGHT_ADC_DIGITAL_VOLUME:
+	case NAU8822_REG_EQ1 ... NAU8822_REG_EQ5:
+	case NAU8822_REG_DAC_LIMITER_1 ... NAU8822_REG_DAC_LIMITER_2:
+	case NAU8822_REG_NOTCH_FILTER_1 ... NAU8822_REG_NOTCH_FILTER_4:
+	case NAU8822_REG_ALC_CONTROL_1 ...NAU8822_REG_PLL_K3:
+	case NAU8822_REG_3D_CONTROL:
+	case NAU8822_REG_RIGHT_SPEAKER_CONTROL:
+	case NAU8822_REG_INPUT_CONTROL ... NAU8822_REG_LEFT_ADC_BOOST_CONTROL:
+	case NAU8822_REG_RIGHT_ADC_BOOST_CONTROL ... NAU8822_REG_AUX1_MIXER:
+	case NAU8822_REG_POWER_MANAGEMENT_4 ... NAU8822_REG_DEVICE_ID:
+	case NAU8822_REG_DAC_DITHER:
+	case NAU8822_REG_ALC_ENHANCE_1 ... NAU8822_REG_MISC_CONTROL:
+	case NAU8822_REG_INPUT_TIEOFF ... NAU8822_REG_OUTPUT_TIEOFF:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool nau8822_writeable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case NAU8822_REG_RESET ... NAU8822_REG_JACK_DETECT_CONTROL_1:
+	case NAU8822_REG_DAC_CONTROL ... NAU8822_REG_LEFT_ADC_DIGITAL_VOLUME:
+	case NAU8822_REG_RIGHT_ADC_DIGITAL_VOLUME:
+	case NAU8822_REG_EQ1 ... NAU8822_REG_EQ5:
+	case NAU8822_REG_DAC_LIMITER_1 ... NAU8822_REG_DAC_LIMITER_2:
+	case NAU8822_REG_NOTCH_FILTER_1 ... NAU8822_REG_NOTCH_FILTER_4:
+	case NAU8822_REG_ALC_CONTROL_1 ...NAU8822_REG_PLL_K3:
+	case NAU8822_REG_3D_CONTROL:
+	case NAU8822_REG_RIGHT_SPEAKER_CONTROL:
+	case NAU8822_REG_INPUT_CONTROL ... NAU8822_REG_LEFT_ADC_BOOST_CONTROL:
+	case NAU8822_REG_RIGHT_ADC_BOOST_CONTROL ... NAU8822_REG_AUX1_MIXER:
+	case NAU8822_REG_POWER_MANAGEMENT_4 ... NAU8822_REG_DEVICE_ID:
+	case NAU8822_REG_DAC_DITHER:
+	case NAU8822_REG_ALC_ENHANCE_1 ... NAU8822_REG_MISC_CONTROL:
+	case NAU8822_REG_INPUT_TIEOFF ... NAU8822_REG_OUTPUT_TIEOFF:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool nau8822_volatile(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case NAU8822_REG_RESET:
+	case NAU8822_REG_DEVICE_REVISION:
+	case NAU8822_REG_DEVICE_ID:
+	case NAU8822_REG_AGC_PEAK2PEAK:
+	case NAU8822_REG_AGC_PEAK_DETECT:
+	case NAU8822_REG_AUTOMUTE_CONTROL:
+		return true;
+	default:
+		return false;
+	}
+}
+
+/* The EQ parameters get function is to get the 5 band equalizer control.
+ * The regmap raw read can't work here because regmap doesn't provide
+ * value format for value width of 9 bits. Therefore, the driver reads data
+ * from cache and makes value format according to the endianness of
+ * bytes type control element.
+ */
+static int nau8822_eq_get(struct snd_kcontrol *kcontrol,
+	struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *component =
+			snd_soc_kcontrol_component(kcontrol);
+	struct soc_bytes_ext *params = (void *)kcontrol->private_value;
+	int i, reg;
+	u16 reg_val, *val;
+
+	val = (u16 *)ucontrol->value.bytes.data;
+	reg = NAU8822_REG_EQ1;
+	for (i = 0; i < params->max / sizeof(u16); i++) {
+		reg_val = snd_soc_component_read32(component, reg + i);
+		/* conversion of 16-bit integers between native CPU format
+		 * and big endian format
+		 */
+		reg_val = cpu_to_be16(reg_val);
+		memcpy(val + i, &reg_val, sizeof(reg_val));
+	}
+
+	return 0;
+}
+
+/* The EQ parameters put function is to make configuration of 5 band equalizer
+ * control. These configuration includes central frequency, equalizer gain,
+ * cut-off frequency, bandwidth control, and equalizer path.
+ * The regmap raw write can't work here because regmap doesn't provide
+ * register and value format for register with address 7 bits and value 9 bits.
+ * Therefore, the driver makes value format according to the endianness of
+ * bytes type control element and writes data to codec.
+ */
+static int nau8822_eq_put(struct snd_kcontrol *kcontrol,
+	struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *component =
+			snd_soc_kcontrol_component(kcontrol);
+	struct soc_bytes_ext *params = (void *)kcontrol->private_value;
+	void *data;
+	u16 *val, value;
+	int i, reg, ret;
+
+	data = kmemdup(ucontrol->value.bytes.data,
+		params->max, GFP_KERNEL | GFP_DMA);
+	if (!data)
+		return -ENOMEM;
+
+	val = (u16 *)data;
+	reg = NAU8822_REG_EQ1;
+	for (i = 0; i < params->max / sizeof(u16); i++) {
+		/* conversion of 16-bit integers between native CPU format
+		 * and big endian format
+		 */
+		value = be16_to_cpu(*(val + i));
+		ret = snd_soc_component_write(component, reg + i, value);
+		if (ret) {
+			dev_err(component->dev,
+			    "EQ configuration fail, register: %x ret: %d\n",
+			    reg + i, ret);
+			kfree(data);
+			return ret;
+		}
+	}
+	kfree(data);
+
+	return 0;
+}
+
+static const char * const nau8822_companding[] = {
+	"Off", "NC", "u-law", "A-law"};
+
+static const struct soc_enum nau8822_companding_adc_enum =
+	SOC_ENUM_SINGLE(NAU8822_REG_COMPANDING_CONTROL, NAU8822_ADCCM_SFT,
+		ARRAY_SIZE(nau8822_companding), nau8822_companding);
+
+static const struct soc_enum nau8822_companding_dac_enum =
+	SOC_ENUM_SINGLE(NAU8822_REG_COMPANDING_CONTROL, NAU8822_DACCM_SFT,
+		ARRAY_SIZE(nau8822_companding), nau8822_companding);
+
+static const char * const nau8822_eqmode[] = {"Capture", "Playback"};
+
+static const struct soc_enum nau8822_eqmode_enum =
+	SOC_ENUM_SINGLE(NAU8822_REG_EQ1, NAU8822_EQM_SFT,
+		ARRAY_SIZE(nau8822_eqmode), nau8822_eqmode);
+
+static const char * const nau8822_alc1[] = {"Off", "Right", "Left", "Both"};
+static const char * const nau8822_alc3[] = {"Normal", "Limiter"};
+
+static const struct soc_enum nau8822_alc_enable_enum =
+	SOC_ENUM_SINGLE(NAU8822_REG_ALC_CONTROL_1, NAU8822_ALCEN_SFT,
+		ARRAY_SIZE(nau8822_alc1), nau8822_alc1);
+
+static const struct soc_enum nau8822_alc_mode_enum =
+	SOC_ENUM_SINGLE(NAU8822_REG_ALC_CONTROL_3, NAU8822_ALCM_SFT,
+		ARRAY_SIZE(nau8822_alc3), nau8822_alc3);
+
+static const DECLARE_TLV_DB_SCALE(digital_tlv, -12750, 50, 1);
+static const DECLARE_TLV_DB_SCALE(inpga_tlv, -1200, 75, 0);
+static const DECLARE_TLV_DB_SCALE(spk_tlv, -5700, 100, 0);
+static const DECLARE_TLV_DB_SCALE(pga_boost_tlv, 0, 2000, 0);
+static const DECLARE_TLV_DB_SCALE(boost_tlv, -1500, 300, 1);
+static const DECLARE_TLV_DB_SCALE(limiter_tlv, 0, 100, 0);
+
+static const struct snd_kcontrol_new nau8822_snd_controls[] = {
+	SOC_ENUM("ADC Companding", nau8822_companding_adc_enum),
+	SOC_ENUM("DAC Companding", nau8822_companding_dac_enum),
+
+	SOC_ENUM("EQ Function", nau8822_eqmode_enum),
+	SND_SOC_BYTES_EXT("EQ Parameters", 10,
+		  nau8822_eq_get, nau8822_eq_put),
+
+	SOC_DOUBLE("DAC Inversion Switch",
+		NAU8822_REG_DAC_CONTROL, 0, 1, 1, 0),
+	SOC_DOUBLE_R_TLV("PCM Volume",
+		NAU8822_REG_LEFT_DAC_DIGITAL_VOLUME,
+		NAU8822_REG_RIGHT_DAC_DIGITAL_VOLUME, 0, 255, 0, digital_tlv),
+
+	SOC_SINGLE("High Pass Filter Switch",
+		NAU8822_REG_ADC_CONTROL, 8, 1, 0),
+	SOC_SINGLE("High Pass Cut Off",
+		NAU8822_REG_ADC_CONTROL, 4, 7, 0),
+
+	SOC_DOUBLE("ADC Inversion Switch",
+		NAU8822_REG_ADC_CONTROL, 0, 1, 1, 0),
+	SOC_DOUBLE_R_TLV("ADC Volume",
+		NAU8822_REG_LEFT_ADC_DIGITAL_VOLUME,
+		NAU8822_REG_RIGHT_ADC_DIGITAL_VOLUME, 0, 255, 0, digital_tlv),
+
+	SOC_SINGLE("DAC Limiter Switch",
+		NAU8822_REG_DAC_LIMITER_1, 8, 1, 0),
+	SOC_SINGLE("DAC Limiter Decay",
+		NAU8822_REG_DAC_LIMITER_1, 4, 15, 0),
+	SOC_SINGLE("DAC Limiter Attack",
+		NAU8822_REG_DAC_LIMITER_1, 0, 15, 0),
+	SOC_SINGLE("DAC Limiter Threshold",
+		NAU8822_REG_DAC_LIMITER_2, 4, 7, 0),
+	SOC_SINGLE_TLV("DAC Limiter Volume",
+		NAU8822_REG_DAC_LIMITER_2, 0, 12, 0, limiter_tlv),
+
+	SOC_ENUM("ALC Mode", nau8822_alc_mode_enum),
+	SOC_ENUM("ALC Enable Switch", nau8822_alc_enable_enum),
+	SOC_SINGLE("ALC Min Gain",
+		NAU8822_REG_ALC_CONTROL_1, 0, 7, 0),
+	SOC_SINGLE("ALC Max Gain",
+		NAU8822_REG_ALC_CONTROL_1, 3, 7, 0),
+	SOC_SINGLE("ALC Hold",
+		NAU8822_REG_ALC_CONTROL_2, 4, 10, 0),
+	SOC_SINGLE("ALC Target",
+		NAU8822_REG_ALC_CONTROL_2, 0, 15, 0),
+	SOC_SINGLE("ALC Decay",
+		NAU8822_REG_ALC_CONTROL_3, 4, 10, 0),
+	SOC_SINGLE("ALC Attack",
+		NAU8822_REG_ALC_CONTROL_3, 0, 10, 0),
+	SOC_SINGLE("ALC Noise Gate Switch",
+		NAU8822_REG_NOISE_GATE, 3, 1, 0),
+	SOC_SINGLE("ALC Noise Gate Threshold",
+		NAU8822_REG_NOISE_GATE, 0, 7, 0),
+
+	SOC_DOUBLE_R("PGA ZC Switch",
+		NAU8822_REG_LEFT_INP_PGA_CONTROL,
+		NAU8822_REG_RIGHT_INP_PGA_CONTROL,
+		7, 1, 0),
+	SOC_DOUBLE_R_TLV("PGA Volume",
+		NAU8822_REG_LEFT_INP_PGA_CONTROL,
+		NAU8822_REG_RIGHT_INP_PGA_CONTROL, 0, 63, 0, inpga_tlv),
+
+	SOC_DOUBLE_R("Headphone ZC Switch",
+		NAU8822_REG_LHP_VOLUME,
+		NAU8822_REG_RHP_VOLUME, 7, 1, 0),
+	SOC_DOUBLE_R("Headphone Playback Switch",
+		NAU8822_REG_LHP_VOLUME,
+		NAU8822_REG_RHP_VOLUME, 6, 1, 1),
+	SOC_DOUBLE_R_TLV("Headphone Volume",
+		NAU8822_REG_LHP_VOLUME,
+		NAU8822_REG_RHP_VOLUME,	0, 63, 0, spk_tlv),
+
+	SOC_DOUBLE_R("Speaker ZC Switch",
+		NAU8822_REG_LSPKOUT_VOLUME,
+		NAU8822_REG_RSPKOUT_VOLUME, 7, 1, 0),
+	SOC_DOUBLE_R("Speaker Playback Switch",
+		NAU8822_REG_LSPKOUT_VOLUME,
+		NAU8822_REG_RSPKOUT_VOLUME, 6, 1, 1),
+	SOC_DOUBLE_R_TLV("Speaker Volume",
+		NAU8822_REG_LSPKOUT_VOLUME,
+		NAU8822_REG_RSPKOUT_VOLUME, 0, 63, 0, spk_tlv),
+
+	SOC_DOUBLE_R("AUXOUT Playback Switch",
+		NAU8822_REG_AUX2_MIXER,
+		NAU8822_REG_AUX1_MIXER, 6, 1, 1),
+
+	SOC_DOUBLE_R_TLV("PGA Boost Volume",
+		NAU8822_REG_LEFT_ADC_BOOST_CONTROL,
+		NAU8822_REG_RIGHT_ADC_BOOST_CONTROL, 8, 1, 0, pga_boost_tlv),
+	SOC_DOUBLE_R_TLV("L2/R2 Boost Volume",
+		NAU8822_REG_LEFT_ADC_BOOST_CONTROL,
+		NAU8822_REG_RIGHT_ADC_BOOST_CONTROL, 4, 7, 0, boost_tlv),
+	SOC_DOUBLE_R_TLV("Aux Boost Volume",
+		NAU8822_REG_LEFT_ADC_BOOST_CONTROL,
+		NAU8822_REG_RIGHT_ADC_BOOST_CONTROL, 0, 7, 0, boost_tlv),
+
+	SOC_SINGLE("DAC 128x Oversampling Switch",
+		NAU8822_REG_DAC_CONTROL, 5, 1, 0),
+	SOC_SINGLE("ADC 128x Oversampling Switch",
+		NAU8822_REG_ADC_CONTROL, 5, 1, 0),
+};
+
+/* LMAIN and RMAIN Mixer */
+static const struct snd_kcontrol_new nau8822_left_out_mixer[] = {
+	SOC_DAPM_SINGLE("LINMIX Switch",
+		NAU8822_REG_LEFT_MIXER_CONTROL, 1, 1, 0),
+	SOC_DAPM_SINGLE("LAUX Switch",
+		NAU8822_REG_LEFT_MIXER_CONTROL, 5, 1, 0),
+	SOC_DAPM_SINGLE("LDAC Switch",
+		NAU8822_REG_LEFT_MIXER_CONTROL, 0, 1, 0),
+	SOC_DAPM_SINGLE("RDAC Switch",
+		NAU8822_REG_OUTPUT_CONTROL, 5, 1, 0),
+};
+
+static const struct snd_kcontrol_new nau8822_right_out_mixer[] = {
+	SOC_DAPM_SINGLE("RINMIX Switch",
+		NAU8822_REG_RIGHT_MIXER_CONTROL, 1, 1, 0),
+	SOC_DAPM_SINGLE("RAUX Switch",
+		NAU8822_REG_RIGHT_MIXER_CONTROL, 5, 1, 0),
+	SOC_DAPM_SINGLE("RDAC Switch",
+		NAU8822_REG_RIGHT_MIXER_CONTROL, 0, 1, 0),
+	SOC_DAPM_SINGLE("LDAC Switch",
+		NAU8822_REG_OUTPUT_CONTROL, 6, 1, 0),
+};
+
+/* AUX1 and AUX2 Mixer */
+static const struct snd_kcontrol_new nau8822_auxout1_mixer[] = {
+	SOC_DAPM_SINGLE("RDAC Switch", NAU8822_REG_AUX1_MIXER, 0, 1, 0),
+	SOC_DAPM_SINGLE("RMIX Switch", NAU8822_REG_AUX1_MIXER, 1, 1, 0),
+	SOC_DAPM_SINGLE("RINMIX Switch", NAU8822_REG_AUX1_MIXER, 2, 1, 0),
+	SOC_DAPM_SINGLE("LDAC Switch", NAU8822_REG_AUX1_MIXER, 3, 1, 0),
+	SOC_DAPM_SINGLE("LMIX Switch", NAU8822_REG_AUX1_MIXER, 4, 1, 0),
+};
+
+static const struct snd_kcontrol_new nau8822_auxout2_mixer[] = {
+	SOC_DAPM_SINGLE("LDAC Switch", NAU8822_REG_AUX2_MIXER, 0, 1, 0),
+	SOC_DAPM_SINGLE("LMIX Switch", NAU8822_REG_AUX2_MIXER, 1, 1, 0),
+	SOC_DAPM_SINGLE("LINMIX Switch", NAU8822_REG_AUX2_MIXER, 2, 1, 0),
+	SOC_DAPM_SINGLE("AUX1MIX Output Switch",
+		NAU8822_REG_AUX2_MIXER, 3, 1, 0),
+};
+
+/* Input PGA */
+static const struct snd_kcontrol_new nau8822_left_input_mixer[] = {
+	SOC_DAPM_SINGLE("L2 Switch", NAU8822_REG_INPUT_CONTROL, 2, 1, 0),
+	SOC_DAPM_SINGLE("MicN Switch", NAU8822_REG_INPUT_CONTROL, 1, 1, 0),
+	SOC_DAPM_SINGLE("MicP Switch", NAU8822_REG_INPUT_CONTROL, 0, 1, 0),
+};
+static const struct snd_kcontrol_new nau8822_right_input_mixer[] = {
+	SOC_DAPM_SINGLE("R2 Switch", NAU8822_REG_INPUT_CONTROL, 6, 1, 0),
+	SOC_DAPM_SINGLE("MicN Switch", NAU8822_REG_INPUT_CONTROL, 5, 1, 0),
+	SOC_DAPM_SINGLE("MicP Switch", NAU8822_REG_INPUT_CONTROL, 4, 1, 0),
+};
+
+/* Loopback Switch */
+static const struct snd_kcontrol_new nau8822_loopback =
+	SOC_DAPM_SINGLE("Switch", NAU8822_REG_COMPANDING_CONTROL,
+		NAU8822_ADDAP_SFT, 1, 0);
+
+static int check_mclk_select_pll(struct snd_soc_dapm_widget *source,
+			 struct snd_soc_dapm_widget *sink)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_to_component(source->dapm);
+	unsigned int value;
+
+	value = snd_soc_component_read32(component, NAU8822_REG_CLOCKING);
+
+	return (value & NAU8822_CLKM_MASK);
+}
+
+static const struct snd_soc_dapm_widget nau8822_dapm_widgets[] = {
+	SND_SOC_DAPM_DAC("Left DAC", "Left HiFi Playback",
+		NAU8822_REG_POWER_MANAGEMENT_3, 0, 0),
+	SND_SOC_DAPM_DAC("Right DAC", "Right HiFi Playback",
+		NAU8822_REG_POWER_MANAGEMENT_3, 1, 0),
+	SND_SOC_DAPM_ADC("Left ADC", "Left HiFi Capture",
+		NAU8822_REG_POWER_MANAGEMENT_2, 0, 0),
+	SND_SOC_DAPM_ADC("Right ADC", "Right HiFi Capture",
+		NAU8822_REG_POWER_MANAGEMENT_2, 1, 0),
+
+	SOC_MIXER_ARRAY("Left Output Mixer",
+		NAU8822_REG_POWER_MANAGEMENT_3, 2, 0, nau8822_left_out_mixer),
+	SOC_MIXER_ARRAY("Right Output Mixer",
+		NAU8822_REG_POWER_MANAGEMENT_3,	3, 0, nau8822_right_out_mixer),
+	SOC_MIXER_ARRAY("AUX1 Output Mixer",
+		NAU8822_REG_POWER_MANAGEMENT_1, 7, 0, nau8822_auxout1_mixer),
+	SOC_MIXER_ARRAY("AUX2 Output Mixer",
+		NAU8822_REG_POWER_MANAGEMENT_1,	6, 0, nau8822_auxout2_mixer),
+
+	SOC_MIXER_ARRAY("Left Input Mixer",
+		NAU8822_REG_POWER_MANAGEMENT_2,
+		2, 0, nau8822_left_input_mixer),
+	SOC_MIXER_ARRAY("Right Input Mixer",
+		NAU8822_REG_POWER_MANAGEMENT_2,
+		3, 0, nau8822_right_input_mixer),
+
+	SND_SOC_DAPM_PGA("Left Boost Mixer",
+		NAU8822_REG_POWER_MANAGEMENT_2, 4, 0, NULL, 0),
+	SND_SOC_DAPM_PGA("Right Boost Mixer",
+		NAU8822_REG_POWER_MANAGEMENT_2, 5, 0, NULL, 0),
+
+	SND_SOC_DAPM_PGA("Left Capture PGA",
+		NAU8822_REG_LEFT_INP_PGA_CONTROL, 6, 1, NULL, 0),
+	SND_SOC_DAPM_PGA("Right Capture PGA",
+		NAU8822_REG_RIGHT_INP_PGA_CONTROL, 6, 1, NULL, 0),
+
+	SND_SOC_DAPM_PGA("Left Headphone Out",
+		NAU8822_REG_POWER_MANAGEMENT_2, 7, 0, NULL, 0),
+	SND_SOC_DAPM_PGA("Right Headphone Out",
+		NAU8822_REG_POWER_MANAGEMENT_2, 8, 0, NULL, 0),
+
+	SND_SOC_DAPM_PGA("Left Speaker Out",
+		 NAU8822_REG_POWER_MANAGEMENT_3, 6, 0, NULL, 0),
+	SND_SOC_DAPM_PGA("Right Speaker Out",
+		NAU8822_REG_POWER_MANAGEMENT_3,	5, 0, NULL, 0),
+
+	SND_SOC_DAPM_PGA("AUX1 Out",
+		NAU8822_REG_POWER_MANAGEMENT_3,	8, 0, NULL, 0),
+	SND_SOC_DAPM_PGA("AUX2 Out",
+		NAU8822_REG_POWER_MANAGEMENT_3,	7, 0, NULL, 0),
+
+	SND_SOC_DAPM_SUPPLY("Mic Bias",
+		NAU8822_REG_POWER_MANAGEMENT_1,	4, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("PLL",
+		NAU8822_REG_POWER_MANAGEMENT_1,	5, 0, NULL, 0),
+
+	SND_SOC_DAPM_SWITCH("Digital Loopback", SND_SOC_NOPM, 0, 0,
+		&nau8822_loopback),
+
+	SND_SOC_DAPM_INPUT("LMICN"),
+	SND_SOC_DAPM_INPUT("LMICP"),
+	SND_SOC_DAPM_INPUT("RMICN"),
+	SND_SOC_DAPM_INPUT("RMICP"),
+	SND_SOC_DAPM_INPUT("LAUX"),
+	SND_SOC_DAPM_INPUT("RAUX"),
+	SND_SOC_DAPM_INPUT("L2"),
+	SND_SOC_DAPM_INPUT("R2"),
+	SND_SOC_DAPM_OUTPUT("LHP"),
+	SND_SOC_DAPM_OUTPUT("RHP"),
+	SND_SOC_DAPM_OUTPUT("LSPK"),
+	SND_SOC_DAPM_OUTPUT("RSPK"),
+	SND_SOC_DAPM_OUTPUT("AUXOUT1"),
+	SND_SOC_DAPM_OUTPUT("AUXOUT2"),
+};
+
+static const struct snd_soc_dapm_route nau8822_dapm_routes[] = {
+	{"Right DAC", NULL, "PLL", check_mclk_select_pll},
+	{"Left DAC", NULL, "PLL", check_mclk_select_pll},
+
+	/* LMAIN and RMAIN Mixer */
+	{"Right Output Mixer", "LDAC Switch", "Left DAC"},
+	{"Right Output Mixer", "RDAC Switch", "Right DAC"},
+	{"Right Output Mixer", "RAUX Switch", "RAUX"},
+	{"Right Output Mixer", "RINMIX Switch", "Right Boost Mixer"},
+
+	{"Left Output Mixer", "LDAC Switch", "Left DAC"},
+	{"Left Output Mixer", "RDAC Switch", "Right DAC"},
+	{"Left Output Mixer", "LAUX Switch", "LAUX"},
+	{"Left Output Mixer", "LINMIX Switch", "Left Boost Mixer"},
+
+	/* AUX1 and AUX2 Mixer */
+	{"AUX1 Output Mixer", "RDAC Switch", "Right DAC"},
+	{"AUX1 Output Mixer", "RMIX Switch", "Right Output Mixer"},
+	{"AUX1 Output Mixer", "RINMIX Switch", "Right Boost Mixer"},
+	{"AUX1 Output Mixer", "LDAC Switch", "Left DAC"},
+	{"AUX1 Output Mixer", "LMIX Switch", "Left Output Mixer"},
+
+	{"AUX2 Output Mixer", "LDAC Switch", "Left DAC"},
+	{"AUX2 Output Mixer", "LMIX Switch", "Left Output Mixer"},
+	{"AUX2 Output Mixer", "LINMIX Switch", "Left Boost Mixer"},
+	{"AUX2 Output Mixer", "AUX1MIX Output Switch", "AUX1 Output Mixer"},
+
+	/* Outputs */
+	{"Right Headphone Out", NULL, "Right Output Mixer"},
+	{"RHP", NULL, "Right Headphone Out"},
+
+	{"Left Headphone Out", NULL, "Left Output Mixer"},
+	{"LHP", NULL, "Left Headphone Out"},
+
+	{"Right Speaker Out", NULL, "Right Output Mixer"},
+	{"RSPK", NULL, "Right Speaker Out"},
+
+	{"Left Speaker Out", NULL, "Left Output Mixer"},
+	{"LSPK", NULL, "Left Speaker Out"},
+
+	{"AUX1 Out", NULL, "AUX1 Output Mixer"},
+	{"AUX2 Out", NULL, "AUX2 Output Mixer"},
+	{"AUXOUT1", NULL, "AUX1 Out"},
+	{"AUXOUT2", NULL, "AUX2 Out"},
+
+	/* Boost Mixer */
+	{"Right ADC", NULL, "PLL", check_mclk_select_pll},
+	{"Left ADC", NULL, "PLL", check_mclk_select_pll},
+
+	{"Right ADC", NULL, "Right Boost Mixer"},
+
+	{"Right Boost Mixer", NULL, "RAUX"},
+	{"Right Boost Mixer", NULL, "Right Capture PGA"},
+	{"Right Boost Mixer", NULL, "R2"},
+
+	{"Left ADC", NULL, "Left Boost Mixer"},
+
+	{"Left Boost Mixer", NULL, "LAUX"},
+	{"Left Boost Mixer", NULL, "Left Capture PGA"},
+	{"Left Boost Mixer", NULL, "L2"},
+
+	/* Input PGA */
+	{"Right Capture PGA", NULL, "Right Input Mixer"},
+	{"Left Capture PGA", NULL, "Left Input Mixer"},
+
+	/* Enable Microphone Power */
+	{"Right Capture PGA", NULL, "Mic Bias"},
+	{"Left Capture PGA", NULL, "Mic Bias"},
+
+	{"Right Input Mixer", "R2 Switch", "R2"},
+	{"Right Input Mixer", "MicN Switch", "RMICN"},
+	{"Right Input Mixer", "MicP Switch", "RMICP"},
+
+	{"Left Input Mixer", "L2 Switch", "L2"},
+	{"Left Input Mixer", "MicN Switch", "LMICN"},
+	{"Left Input Mixer", "MicP Switch", "LMICP"},
+
+	/* Digital Loopback */
+	{"Digital Loopback", "Switch", "Left ADC"},
+	{"Digital Loopback", "Switch", "Right ADC"},
+	{"Left DAC", NULL, "Digital Loopback"},
+	{"Right DAC", NULL, "Digital Loopback"},
+};
+
+static int nau8822_set_dai_sysclk(struct snd_soc_dai *dai, int clk_id,
+				 unsigned int freq, int dir)
+{
+	struct snd_soc_component *component = dai->component;
+	struct nau8822 *nau8822 = snd_soc_component_get_drvdata(component);
+
+	nau8822->div_id = clk_id;
+	nau8822->sysclk = freq;
+	dev_dbg(component->dev, "master sysclk %dHz, source %s\n", freq,
+		clk_id == NAU8822_CLK_PLL ? "PLL" : "MCLK");
+
+	return 0;
+}
+
+static int nau8822_calc_pll(unsigned int pll_in, unsigned int fs,
+				struct nau8822_pll *pll_param)
+{
+	u64 f2, f2_max, pll_ratio;
+	int i, scal_sel;
+
+	if (pll_in > NAU_PLL_REF_MAX || pll_in < NAU_PLL_REF_MIN)
+		return -EINVAL;
+	f2_max = 0;
+	scal_sel = ARRAY_SIZE(nau8822_mclk_scaler);
+
+	for (i = 0; i < scal_sel; i++) {
+		f2 = 256 * fs * 4 * nau8822_mclk_scaler[i] / 10;
+		if (f2 > NAU_PLL_FREQ_MIN && f2 < NAU_PLL_FREQ_MAX &&
+			f2_max < f2) {
+			f2_max = f2;
+			scal_sel = i;
+		}
+	}
+
+	if (ARRAY_SIZE(nau8822_mclk_scaler) == scal_sel)
+		return -EINVAL;
+	pll_param->mclk_scaler = scal_sel;
+	f2 = f2_max;
+
+	/* Calculate the PLL 4-bit integer input and the PLL 24-bit fractional
+	 * input; round up the 24+4bit.
+	 */
+	pll_ratio = div_u64(f2 << 28, pll_in);
+	pll_param->pre_factor = 0;
+	if (((pll_ratio >> 28) & 0xF) < NAU_PLL_OPTOP_MIN) {
+		pll_ratio <<= 1;
+		pll_param->pre_factor = 1;
+	}
+	pll_param->pll_int = (pll_ratio >> 28) & 0xF;
+	pll_param->pll_frac = ((pll_ratio & 0xFFFFFFF) >> 4);
+
+	return 0;
+}
+
+static int nau8822_config_clkdiv(struct snd_soc_dai *dai, int div, int rate)
+{
+	struct snd_soc_component *component = dai->component;
+	struct nau8822 *nau8822 = snd_soc_component_get_drvdata(component);
+	struct nau8822_pll *pll = &nau8822->pll;
+	int i, sclk, imclk;
+
+	switch (nau8822->div_id) {
+	case NAU8822_CLK_MCLK:
+		/* Configure the master clock prescaler div to make system
+		 * clock to approximate the internal master clock (IMCLK);
+		 * and large or equal to IMCLK.
+		 */
+		div = 0;
+		imclk = rate * 256;
+		for (i = 1; i < ARRAY_SIZE(nau8822_mclk_scaler); i++) {
+			sclk = (nau8822->sysclk * 10) /	nau8822_mclk_scaler[i];
+			if (sclk < imclk)
+				break;
+			div = i;
+		}
+		dev_dbg(component->dev, "master clock prescaler %x for fs %d\n",
+			div, rate);
+
+		/* master clock from MCLK and disable PLL */
+		snd_soc_component_update_bits(component,
+			NAU8822_REG_CLOCKING, NAU8822_MCLKSEL_MASK,
+			(div << NAU8822_MCLKSEL_SFT));
+		snd_soc_component_update_bits(component,
+			NAU8822_REG_CLOCKING, NAU8822_CLKM_MASK,
+			NAU8822_CLKM_MCLK);
+		break;
+
+	case NAU8822_CLK_PLL:
+		/* master clock from PLL and enable PLL */
+		if (pll->mclk_scaler != div) {
+			dev_err(component->dev,
+			"master clock prescaler not meet PLL parameters\n");
+			return -EINVAL;
+		}
+		snd_soc_component_update_bits(component,
+			NAU8822_REG_CLOCKING, NAU8822_MCLKSEL_MASK,
+			(div << NAU8822_MCLKSEL_SFT));
+		snd_soc_component_update_bits(component,
+			NAU8822_REG_CLOCKING, NAU8822_CLKM_MASK,
+			NAU8822_CLKM_PLL);
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int nau8822_set_pll(struct snd_soc_dai *dai, int pll_id, int source,
+				unsigned int freq_in, unsigned int freq_out)
+{
+	struct snd_soc_component *component = dai->component;
+	struct nau8822 *nau8822 = snd_soc_component_get_drvdata(component);
+	struct nau8822_pll *pll_param = &nau8822->pll;
+	int ret, fs;
+
+	fs = freq_out / 256;
+
+	ret = nau8822_calc_pll(freq_in, fs, pll_param);
+	if (ret < 0) {
+		dev_err(component->dev, "Unsupported input clock %d\n",
+			freq_in);
+		return ret;
+	}
+
+	dev_info(component->dev,
+		"pll_int=%x pll_frac=%x mclk_scaler=%x pre_factor=%x\n",
+		pll_param->pll_int, pll_param->pll_frac,
+		pll_param->mclk_scaler, pll_param->pre_factor);
+
+	snd_soc_component_update_bits(component,
+		NAU8822_REG_PLL_N, NAU8822_PLLMCLK_DIV2 | NAU8822_PLLN_MASK,
+		(pll_param->pre_factor ? NAU8822_PLLMCLK_DIV2 : 0) |
+		pll_param->pll_int);
+	snd_soc_component_write(component,
+		NAU8822_REG_PLL_K1, (pll_param->pll_frac >> NAU8822_PLLK1_SFT) &
+		NAU8822_PLLK1_MASK);
+	snd_soc_component_write(component,
+		NAU8822_REG_PLL_K2, (pll_param->pll_frac >> NAU8822_PLLK2_SFT) &
+		NAU8822_PLLK2_MASK);
+	snd_soc_component_write(component,
+		NAU8822_REG_PLL_K3, pll_param->pll_frac & NAU8822_PLLK3_MASK);
+	snd_soc_component_update_bits(component,
+		NAU8822_REG_CLOCKING, NAU8822_MCLKSEL_MASK,
+		pll_param->mclk_scaler << NAU8822_MCLKSEL_SFT);
+	snd_soc_component_update_bits(component,
+		NAU8822_REG_CLOCKING, NAU8822_CLKM_MASK, NAU8822_CLKM_PLL);
+
+	return 0;
+}
+
+static int nau8822_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt)
+{
+	struct snd_soc_component *component = dai->component;
+	u16 ctrl1_val = 0, ctrl2_val = 0;
+
+	dev_dbg(component->dev, "%s\n", __func__);
+
+	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
+	case SND_SOC_DAIFMT_CBM_CFM:
+		ctrl2_val |= 1;
+		break;
+	case SND_SOC_DAIFMT_CBS_CFS:
+		ctrl2_val &= ~1;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+	case SND_SOC_DAIFMT_I2S:
+		ctrl1_val |= 0x10;
+		break;
+	case SND_SOC_DAIFMT_RIGHT_J:
+		break;
+	case SND_SOC_DAIFMT_LEFT_J:
+		ctrl1_val |= 0x8;
+		break;
+	case SND_SOC_DAIFMT_DSP_A:
+		ctrl1_val |= 0x18;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_NB_NF:
+		break;
+	case SND_SOC_DAIFMT_IB_IF:
+		ctrl1_val |= 0x180;
+		break;
+	case SND_SOC_DAIFMT_IB_NF:
+		ctrl1_val |= 0x100;
+		break;
+	case SND_SOC_DAIFMT_NB_IF:
+		ctrl1_val |= 0x80;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	snd_soc_component_update_bits(component,
+		NAU8822_REG_AUDIO_INTERFACE,
+		NAU8822_AIFMT_MASK | NAU8822_LRP_MASK | NAU8822_BCLKP_MASK,
+		ctrl1_val);
+	snd_soc_component_update_bits(component,
+		NAU8822_REG_CLOCKING, NAU8822_CLKIOEN_MASK, ctrl2_val);
+
+	return 0;
+}
+
+static int nau8822_hw_params(struct snd_pcm_substream *substream,
+			    struct snd_pcm_hw_params *params,
+			    struct snd_soc_dai *dai)
+{
+	struct snd_soc_component *component = dai->component;
+	struct nau8822 *nau8822 = snd_soc_component_get_drvdata(component);
+	int val_len = 0, val_rate = 0;
+
+	switch (params_format(params)) {
+	case SNDRV_PCM_FORMAT_S16_LE:
+		break;
+	case SNDRV_PCM_FORMAT_S20_3LE:
+		val_len |= NAU8822_WLEN_20;
+		break;
+	case SNDRV_PCM_FORMAT_S24_LE:
+		val_len |= NAU8822_WLEN_24;
+		break;
+	case SNDRV_PCM_FORMAT_S32_LE:
+		val_len |= NAU8822_WLEN_32;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (params_rate(params)) {
+	case 8000:
+		val_rate |= NAU8822_SMPLR_8K;
+		break;
+	case 11025:
+		val_rate |= NAU8822_SMPLR_12K;
+		break;
+	case 16000:
+		val_rate |= NAU8822_SMPLR_16K;
+		break;
+	case 22050:
+		val_rate |= NAU8822_SMPLR_24K;
+		break;
+	case 32000:
+		val_rate |= NAU8822_SMPLR_32K;
+		break;
+	case 44100:
+	case 48000:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	snd_soc_component_update_bits(component,
+		NAU8822_REG_AUDIO_INTERFACE, NAU8822_WLEN_MASK, val_len);
+	snd_soc_component_update_bits(component,
+		NAU8822_REG_ADDITIONAL_CONTROL, NAU8822_SMPLR_MASK, val_rate);
+
+	/* If the master clock is from MCLK, provide the runtime FS for driver
+	 * to get the master clock prescaler configuration.
+	 */
+	if (nau8822->div_id == NAU8822_CLK_MCLK)
+		nau8822_config_clkdiv(dai, 0, params_rate(params));
+
+	return 0;
+}
+
+static int nau8822_mute(struct snd_soc_dai *dai, int mute)
+{
+	struct snd_soc_component *component = dai->component;
+
+	dev_dbg(component->dev, "%s: %d\n", __func__, mute);
+
+	if (mute)
+		snd_soc_component_update_bits(component,
+			NAU8822_REG_DAC_CONTROL, 0x40, 0x40);
+	else
+		snd_soc_component_update_bits(component,
+			NAU8822_REG_DAC_CONTROL, 0x40, 0);
+
+	return 0;
+}
+
+static int nau8822_set_bias_level(struct snd_soc_component *component,
+				 enum snd_soc_bias_level level)
+{
+	switch (level) {
+	case SND_SOC_BIAS_ON:
+	case SND_SOC_BIAS_PREPARE:
+		snd_soc_component_update_bits(component,
+			NAU8822_REG_POWER_MANAGEMENT_1,
+			NAU8822_REFIMP_MASK, NAU8822_REFIMP_80K);
+		break;
+
+	case SND_SOC_BIAS_STANDBY:
+		snd_soc_component_update_bits(component,
+			NAU8822_REG_POWER_MANAGEMENT_1,
+			NAU8822_IOBUF_EN | NAU8822_ABIAS_EN,
+			NAU8822_IOBUF_EN | NAU8822_ABIAS_EN);
+
+		if (snd_soc_component_get_bias_level(component) ==
+			SND_SOC_BIAS_OFF) {
+			snd_soc_component_update_bits(component,
+				NAU8822_REG_POWER_MANAGEMENT_1,
+				NAU8822_REFIMP_MASK, NAU8822_REFIMP_3K);
+			mdelay(100);
+		}
+		snd_soc_component_update_bits(component,
+			NAU8822_REG_POWER_MANAGEMENT_1,
+			NAU8822_REFIMP_MASK, NAU8822_REFIMP_300K);
+		break;
+
+	case SND_SOC_BIAS_OFF:
+		snd_soc_component_write(component,
+			NAU8822_REG_POWER_MANAGEMENT_1, 0);
+		snd_soc_component_write(component,
+			NAU8822_REG_POWER_MANAGEMENT_2, 0);
+		snd_soc_component_write(component,
+			NAU8822_REG_POWER_MANAGEMENT_3, 0);
+		break;
+	}
+
+	dev_dbg(component->dev, "%s: %d\n", __func__, level);
+
+	return 0;
+}
+
+#define NAU8822_RATES (SNDRV_PCM_RATE_8000_48000)
+
+#define NAU8822_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \
+	SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE)
+
+static const struct snd_soc_dai_ops nau8822_dai_ops = {
+	.hw_params	= nau8822_hw_params,
+	.digital_mute	= nau8822_mute,
+	.set_fmt	= nau8822_set_dai_fmt,
+	.set_sysclk	= nau8822_set_dai_sysclk,
+	.set_pll	= nau8822_set_pll,
+};
+
+static struct snd_soc_dai_driver nau8822_dai = {
+	.name = "nau8822-hifi",
+	.playback = {
+		.stream_name = "Playback",
+		.channels_min = 1,
+		.channels_max = 2,
+		.rates = NAU8822_RATES,
+		.formats = NAU8822_FORMATS,
+	},
+	.capture = {
+		.stream_name = "Capture",
+		.channels_min = 1,
+		.channels_max = 2,
+		.rates = NAU8822_RATES,
+		.formats = NAU8822_FORMATS,
+	},
+	.ops = &nau8822_dai_ops,
+	.symmetric_rates = 1,
+};
+
+static int nau8822_suspend(struct snd_soc_component *component)
+{
+	struct nau8822 *nau8822 = snd_soc_component_get_drvdata(component);
+
+	snd_soc_component_force_bias_level(component, SND_SOC_BIAS_OFF);
+
+	regcache_mark_dirty(nau8822->regmap);
+
+	return 0;
+}
+
+static int nau8822_resume(struct snd_soc_component *component)
+{
+	struct nau8822 *nau8822 = snd_soc_component_get_drvdata(component);
+
+	regcache_sync(nau8822->regmap);
+
+	snd_soc_component_force_bias_level(component, SND_SOC_BIAS_STANDBY);
+
+	return 0;
+}
+
+/*
+ * These registers contain an "update" bit - bit 8. This means, for example,
+ * that one can write new DAC digital volume for both channels, but only when
+ * the update bit is set, will also the volume be updated - simultaneously for
+ * both channels.
+ */
+static const int update_reg[] = {
+	NAU8822_REG_LEFT_DAC_DIGITAL_VOLUME,
+	NAU8822_REG_RIGHT_DAC_DIGITAL_VOLUME,
+	NAU8822_REG_LEFT_ADC_DIGITAL_VOLUME,
+	NAU8822_REG_RIGHT_ADC_DIGITAL_VOLUME,
+	NAU8822_REG_LEFT_INP_PGA_CONTROL,
+	NAU8822_REG_RIGHT_INP_PGA_CONTROL,
+	NAU8822_REG_LHP_VOLUME,
+	NAU8822_REG_RHP_VOLUME,
+	NAU8822_REG_LSPKOUT_VOLUME,
+	NAU8822_REG_RSPKOUT_VOLUME,
+};
+
+static int nau8822_probe(struct snd_soc_component *component)
+{
+	int i;
+
+	/*
+	 * Set the update bit in all registers, that have one. This way all
+	 * writes to those registers will also cause the update bit to be
+	 * written.
+	 */
+	for (i = 0; i < ARRAY_SIZE(update_reg); i++)
+		snd_soc_component_update_bits(component,
+			update_reg[i], 0x100, 0x100);
+
+	return 0;
+}
+
+static const struct snd_soc_component_driver soc_component_dev_nau8822 = {
+	.probe				= nau8822_probe,
+	.suspend			= nau8822_suspend,
+	.resume				= nau8822_resume,
+	.set_bias_level			= nau8822_set_bias_level,
+	.controls			= nau8822_snd_controls,
+	.num_controls			= ARRAY_SIZE(nau8822_snd_controls),
+	.dapm_widgets			= nau8822_dapm_widgets,
+	.num_dapm_widgets		= ARRAY_SIZE(nau8822_dapm_widgets),
+	.dapm_routes			= nau8822_dapm_routes,
+	.num_dapm_routes		= ARRAY_SIZE(nau8822_dapm_routes),
+	.idle_bias_on			= 1,
+	.use_pmdown_time		= 1,
+	.endianness			= 1,
+	.non_legacy_dai_naming		= 1,
+};
+
+static const struct regmap_config nau8822_regmap_config = {
+	.reg_bits = 7,
+	.val_bits = 9,
+
+	.max_register = NAU8822_REG_MAX_REGISTER,
+	.volatile_reg = nau8822_volatile,
+
+	.readable_reg = nau8822_readable_reg,
+	.writeable_reg = nau8822_writeable_reg,
+
+	.cache_type = REGCACHE_RBTREE,
+	.reg_defaults = nau8822_reg_defaults,
+	.num_reg_defaults = ARRAY_SIZE(nau8822_reg_defaults),
+};
+
+static int nau8822_i2c_probe(struct i2c_client *i2c,
+			    const struct i2c_device_id *id)
+{
+	struct device *dev = &i2c->dev;
+	struct nau8822 *nau8822 = dev_get_platdata(dev);
+	int ret;
+
+	if (!nau8822) {
+		nau8822 = devm_kzalloc(dev, sizeof(*nau8822), GFP_KERNEL);
+		if (nau8822 == NULL)
+			return -ENOMEM;
+	}
+	i2c_set_clientdata(i2c, nau8822);
+
+	nau8822->regmap = devm_regmap_init_i2c(i2c, &nau8822_regmap_config);
+	if (IS_ERR(nau8822->regmap)) {
+		ret = PTR_ERR(nau8822->regmap);
+		dev_err(&i2c->dev, "Failed to allocate regmap: %d\n", ret);
+		return ret;
+	}
+	nau8822->dev = dev;
+
+	/* Reset the codec */
+	ret = regmap_write(nau8822->regmap, NAU8822_REG_RESET, 0x00);
+	if (ret != 0) {
+		dev_err(&i2c->dev, "Failed to issue reset: %d\n", ret);
+		return ret;
+	}
+
+	ret = devm_snd_soc_register_component(dev, &soc_component_dev_nau8822,
+						&nau8822_dai, 1);
+	if (ret != 0) {
+		dev_err(&i2c->dev, "Failed to register CODEC: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct i2c_device_id nau8822_i2c_id[] = {
+	{ "nau8822", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, nau8822_i2c_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id nau8822_of_match[] = {
+	{ .compatible = "nuvoton,nau8822", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, nau8822_of_match);
+#endif
+
+static struct i2c_driver nau8822_i2c_driver = {
+	.driver = {
+		.name = "nau8822",
+		.of_match_table = of_match_ptr(nau8822_of_match),
+	},
+	.probe =    nau8822_i2c_probe,
+	.id_table = nau8822_i2c_id,
+};
+module_i2c_driver(nau8822_i2c_driver);
+
+MODULE_DESCRIPTION("ASoC NAU8822 codec driver");
+MODULE_AUTHOR("David Lin <ctlin0@nuvoton.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/sound/soc/codecs/nau8822.h b/sound/soc/codecs/nau8822.h
new file mode 100644
index 000000000000..aa79c969cd44
--- /dev/null
+++ b/sound/soc/codecs/nau8822.h
@@ -0,0 +1,204 @@ 
+/*
+ * nau8822.h  --  NAU8822 Soc Audio Codec driver
+ *
+ * Author: David Lin <ctlin0@nuvoton.com>
+ * Co-author: John Hsu <kchsu0@nuvoton.com>
+ * Co-author: Seven Li <wtli@nuvoton.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __NAU8822_H__
+#define __NAU8822_H__
+
+#define NAU8822_REG_RESET			0x00
+#define NAU8822_REG_POWER_MANAGEMENT_1		0x01
+#define NAU8822_REG_POWER_MANAGEMENT_2		0x02
+#define NAU8822_REG_POWER_MANAGEMENT_3		0x03
+#define NAU8822_REG_AUDIO_INTERFACE		0x04
+#define NAU8822_REG_COMPANDING_CONTROL		0x05
+#define NAU8822_REG_CLOCKING			0x06
+#define NAU8822_REG_ADDITIONAL_CONTROL		0x07
+#define NAU8822_REG_GPIO_CONTROL		0x08
+#define NAU8822_REG_JACK_DETECT_CONTROL_1	0x09
+#define NAU8822_REG_DAC_CONTROL			0x0A
+#define NAU8822_REG_LEFT_DAC_DIGITAL_VOLUME	0x0B
+#define NAU8822_REG_RIGHT_DAC_DIGITAL_VOLUME	0x0C
+#define NAU8822_REG_JACK_DETECT_CONTROL_2	0x0D
+#define NAU8822_REG_ADC_CONTROL			0x0E
+#define NAU8822_REG_LEFT_ADC_DIGITAL_VOLUME	0x0F
+#define NAU8822_REG_RIGHT_ADC_DIGITAL_VOLUME	0x10
+#define NAU8822_REG_EQ1				0x12
+#define NAU8822_REG_EQ2				0x13
+#define NAU8822_REG_EQ3				0x14
+#define NAU8822_REG_EQ4				0x15
+#define NAU8822_REG_EQ5				0x16
+#define NAU8822_REG_DAC_LIMITER_1		0x18
+#define NAU8822_REG_DAC_LIMITER_2		0x19
+#define NAU8822_REG_NOTCH_FILTER_1		0x1B
+#define NAU8822_REG_NOTCH_FILTER_2		0x1C
+#define NAU8822_REG_NOTCH_FILTER_3		0x1D
+#define NAU8822_REG_NOTCH_FILTER_4		0x1E
+#define NAU8822_REG_ALC_CONTROL_1		0x20
+#define NAU8822_REG_ALC_CONTROL_2		0x21
+#define NAU8822_REG_ALC_CONTROL_3		0x22
+#define NAU8822_REG_NOISE_GATE			0x23
+#define NAU8822_REG_PLL_N			0x24
+#define NAU8822_REG_PLL_K1			0x25
+#define NAU8822_REG_PLL_K2			0x26
+#define NAU8822_REG_PLL_K3			0x27
+#define NAU8822_REG_3D_CONTROL			0x29
+#define NAU8822_REG_RIGHT_SPEAKER_CONTROL	0x2B
+#define NAU8822_REG_INPUT_CONTROL		0x2C
+#define NAU8822_REG_LEFT_INP_PGA_CONTROL	0x2D
+#define NAU8822_REG_RIGHT_INP_PGA_CONTROL	0x2E
+#define NAU8822_REG_LEFT_ADC_BOOST_CONTROL	0x2F
+#define NAU8822_REG_RIGHT_ADC_BOOST_CONTROL	0x30
+#define NAU8822_REG_OUTPUT_CONTROL		0x31
+#define NAU8822_REG_LEFT_MIXER_CONTROL		0x32
+#define NAU8822_REG_RIGHT_MIXER_CONTROL		0x33
+#define NAU8822_REG_LHP_VOLUME			0x34
+#define NAU8822_REG_RHP_VOLUME			0x35
+#define NAU8822_REG_LSPKOUT_VOLUME		0x36
+#define NAU8822_REG_RSPKOUT_VOLUME		0x37
+#define NAU8822_REG_AUX2_MIXER			0x38
+#define NAU8822_REG_AUX1_MIXER			0x39
+#define NAU8822_REG_POWER_MANAGEMENT_4		0x3A
+#define NAU8822_REG_LEFT_TIME_SLOT		0x3B
+#define NAU8822_REG_MISC			0x3C
+#define NAU8822_REG_RIGHT_TIME_SLOT		0x3D
+#define NAU8822_REG_DEVICE_REVISION		0x3E
+#define NAU8822_REG_DEVICE_ID			0x3F
+#define NAU8822_REG_DAC_DITHER			0x41
+#define NAU8822_REG_ALC_ENHANCE_1		0x46
+#define NAU8822_REG_ALC_ENHANCE_2		0x47
+#define NAU8822_REG_192KHZ_SAMPLING		0x48
+#define NAU8822_REG_MISC_CONTROL		0x49
+#define NAU8822_REG_INPUT_TIEOFF		0x4A
+#define NAU8822_REG_POWER_REDUCTION		0x4B
+#define NAU8822_REG_AGC_PEAK2PEAK		0x4C
+#define NAU8822_REG_AGC_PEAK_DETECT		0x4D
+#define NAU8822_REG_AUTOMUTE_CONTROL		0x4E
+#define NAU8822_REG_OUTPUT_TIEOFF		0x4F
+#define NAU8822_REG_MAX_REGISTER		NAU8822_REG_OUTPUT_TIEOFF
+
+/* NAU8822_REG_POWER_MANAGEMENT_1 (0x1) */
+#define NAU8822_REFIMP_MASK			0x3
+#define NAU8822_REFIMP_80K			0x1
+#define NAU8822_REFIMP_300K			0x2
+#define NAU8822_REFIMP_3K			0x3
+#define NAU8822_IOBUF_EN			(0x1 << 2)
+#define NAU8822_ABIAS_EN			(0x1 << 3)
+
+/* NAU8822_REG_AUDIO_INTERFACE (0x4) */
+#define NAU8822_AIFMT_MASK			(0x3 << 3)
+#define NAU8822_WLEN_MASK			(0x3 << 5)
+#define NAU8822_WLEN_20				(0x1 << 5)
+#define NAU8822_WLEN_24				(0x2 << 5)
+#define NAU8822_WLEN_32				(0x3 << 5)
+#define NAU8822_LRP_MASK			(0x1 << 7)
+#define NAU8822_BCLKP_MASK			(0x1 << 8)
+
+/* NAU8822_REG_COMPANDING_CONTROL (0x5) */
+#define NAU8822_ADDAP_SFT			0
+#define NAU8822_ADCCM_SFT			1
+#define NAU8822_DACCM_SFT			3
+
+/* NAU8822_REG_CLOCKING (0x6) */
+#define NAU8822_CLKIOEN_MASK			0x1
+#define NAU8822_MCLKSEL_SFT			5
+#define NAU8822_MCLKSEL_MASK			(0x7 << 5)
+#define NAU8822_BCLKSEL_SFT			2
+#define NAU8822_BCLKSEL_MASK			(0x7 << 2)
+#define NAU8822_CLKM_MASK			(0x1 << 8)
+#define NAU8822_CLKM_MCLK			(0x0 << 8)
+#define NAU8822_CLKM_PLL			(0x1 << 8)
+
+/* NAU8822_REG_ADDITIONAL_CONTROL (0x08) */
+#define NAU8822_SMPLR_SFT			1
+#define NAU8822_SMPLR_MASK			(0x7 << 1)
+#define NAU8822_SMPLR_48K			(0x0 << 1)
+#define NAU8822_SMPLR_32K			(0x1 << 1)
+#define NAU8822_SMPLR_24K			(0x2 << 1)
+#define NAU8822_SMPLR_16K			(0x3 << 1)
+#define NAU8822_SMPLR_12K			(0x4 << 1)
+#define NAU8822_SMPLR_8K			(0x5 << 1)
+
+/* NAU8822_REG_EQ1 (0x12) */
+#define NAU8822_EQ1GC_SFT			0
+#define NAU8822_EQ1CF_SFT			5
+#define NAU8822_EQM_SFT				8
+
+/* NAU8822_REG_EQ2 (0x13) */
+#define NAU8822_EQ2GC_SFT			0
+#define NAU8822_EQ2CF_SFT			5
+#define NAU8822_EQ2BW_SFT			8
+
+/* NAU8822_REG_EQ3 (0x14) */
+#define NAU8822_EQ3GC_SFT			0
+#define NAU8822_EQ3CF_SFT			5
+#define NAU8822_EQ3BW_SFT			8
+
+/* NAU8822_REG_EQ4 (0x15) */
+#define NAU8822_EQ4GC_SFT			0
+#define NAU8822_EQ4CF_SFT			5
+#define NAU8822_EQ4BW_SFT			8
+
+/* NAU8822_REG_EQ5 (0x16) */
+#define NAU8822_EQ5GC_SFT			0
+#define NAU8822_EQ5CF_SFT			5
+
+/* NAU8822_REG_ALC_CONTROL_1 (0x20) */
+#define NAU8822_ALCMINGAIN_SFT			0
+#define NAU8822_ALCMXGAIN_SFT			3
+#define NAU8822_ALCEN_SFT			7
+
+/* NAU8822_REG_ALC_CONTROL_2 (0x21) */
+#define NAU8822_ALCSL_SFT			0
+#define NAU8822_ALCHT_SFT			4
+
+/* NAU8822_REG_ALC_CONTROL_3 (0x22) */
+#define NAU8822_ALCATK_SFT			0
+#define NAU8822_ALCDCY_SFT			4
+#define NAU8822_ALCM_SFT			8
+
+/* NAU8822_REG_PLL_N (0x24) */
+#define NAU8822_PLLMCLK_DIV2			(0x1 << 4)
+#define NAU8822_PLLN_MASK			0xF
+
+#define NAU8822_PLLK1_SFT			18
+#define NAU8822_PLLK1_MASK			0x3F
+
+/* NAU8822_REG_PLL_K2 (0x26) */
+#define NAU8822_PLLK2_SFT			9
+#define NAU8822_PLLK2_MASK			0x1FF
+
+/* NAU8822_REG_PLL_K3 (0x27) */
+#define NAU8822_PLLK3_MASK			0x1FF
+
+/* System Clock Source */
+enum {
+	NAU8822_CLK_MCLK,
+	NAU8822_CLK_PLL,
+};
+
+struct nau8822_pll {
+	int pre_factor;
+	int mclk_scaler;
+	int pll_frac;
+	int pll_int;
+};
+
+/* Codec Private Data */
+struct nau8822 {
+	struct device *dev;
+	struct regmap *regmap;
+	int mclk_idx;
+	struct nau8822_pll pll;
+	int sysclk;
+	int div_id;
+};
+
+#endif	/* __NAU8822_H__ */