| Message ID | 20181123142411.8921-3-dev@pschenker.ch (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | None | expand |
On Fri, 23 Nov 2018 15:24:10 +0100 Philippe Schenker <dev@pschenker.ch> wrote: > From: Stefan Agner <stefan@agner.ch> > > This adds the devicetree bindings for the STMPE ADC. > > Signed-off-by: Stefan Agner <stefan@agner.ch> > Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> > Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Clearly this will need review from input and mfd. I've suggested inline that you split the realignment out to a separate patch for reviewability reasons. > --- > > Changes in v3: > - Reformatted documentation for touchscreen to use tabs and have a better > overview of the settings. > - Added note which adc-settings will take precedence. > - changed typo in sample-time setting from 144 clocks to 124 clocks, as stated > in the datasheet. > > Changes in v2: > - Moved the bindings for ADC to the overlying mfd. > - Reformatted for better readability > > .../devicetree/bindings/iio/adc/stmpe-adc.txt | 21 +++++++ > .../bindings/input/touchscreen/stmpe.txt | 60 ++++++++++++------- > .../devicetree/bindings/mfd/stmpe.txt | 28 ++++++--- > 3 files changed, 80 insertions(+), 29 deletions(-) > create mode 100644 Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > > diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > new file mode 100644 > index 000000000000..480e66422625 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > @@ -0,0 +1,21 @@ > +STMPE ADC driver > +---------------- > + > +Required properties: > + - compatible: "st,stmpe-adc" > + > +Optional properties: > +Note that the ADC is shared with the STMPE touchscreen. ADC related settings > +have to be done in the mfd. > +- st,norequest-mask: bitmask specifying which ADC channels should _not_ be > + requestable due to different usage (e.g. touch) > + > +Node name must be stmpe_adc and should be child node of stmpe node to > +which it belongs. > + > +Example: > + > + stmpe_adc { Can we use adc { here to match standard naming? > + compatible = "st,stmpe-adc"; > + st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */ > + }; > diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > index 127baa31a77a..414586513a02 100644 > --- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > @@ -5,36 +5,52 @@ Required properties: > - compatible: "st,stmpe-ts" > > Optional properties: > -- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> > - 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 > - -> 144 clocks), recommended is 4. > -- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) > -- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external > - reference) > -- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) > -- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 > - samples, 3 -> 8 samples) > -- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> > - 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended > - is 3 > -- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 > - -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 > -- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of > - the fractional part) recommended is 7 > -- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 > - mA max, 1 -> 50 mA typical 80 mA max) > +- st,ave-ctrl : Sample average control > + 0 -> 1 sample > + 1 -> 2 samples > + 2 -> 4 samples > + 3 -> 8 samples > +- st,touch-det-delay : Touch detect interrupt delay (recommended is 3) > + 0 -> 10 us 5 -> 5 ms > + 1 -> 50 us 6 -> 10 ms > + 2 -> 100 us 7 -> 50 ms > + 3 -> 500 us > + 4-> 1 ms > +- st,settling : Panel driver settling time (recommended is 2) > + 0 -> 10 us 5 -> 10 ms > + 1 -> 100 us 6 for 50 ms > + 2 -> 500 us 7 -> 100 ms > + 3 -> 1 ms > + 4 -> 5 ms > +- st,fraction-z : Length of the fractional part in z (recommended is 7) > + (fraction-z ([0..7]) = Count of the fractional part) > +- st,i-drive : current limit value of the touchscreen drivers > + 0 -> 20 mA (typical 35mA max) > + 1 -> 50 mA (typical 80 mA max) > + > +Optional properties common with MFD (deprecated): > + - st,sample-time : ADC conversion time in number of clock. > + 0 -> 36 clocks 4 -> 80 clocks (recommended) > + 1 -> 44 clocks 5 -> 96 clocks > + 2 -> 56 clocks 6 -> 124 clocks > + 3 -> 64 clocks > + - st,mod-12b : ADC Bit mode > + 0 -> 10bit ADC 1 -> 12bit ADC > + - st,ref-sel : ADC reference source > + 0 -> internal 1 -> external > + - st,adc-freq : ADC Clock speed > + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz > + 1 -> 3.25 MHz > > Node name must be stmpe_touchscreen and should be child node of stmpe node to > which it belongs. > > +Note that common ADC settings of stmpe_touchscreen will take precedence. > + > Example: > > stmpe_touchscreen { > compatible = "st,stmpe-ts"; > - st,sample-time = <4>; > - st,mod-12b = <1>; > - st,ref-sel = <0>; > - st,adc-freq = <1>; > st,ave-ctrl = <1>; > st,touch-det-delay = <2>; > st,settling = <2>; > diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt > index c797c05cd3c2..d4408a417193 100644 > --- a/Documentation/devicetree/bindings/mfd/stmpe.txt > +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt > @@ -4,15 +4,29 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, > keypad, touchscreen, adc, pwm, rotator. > > Required properties: > - - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" > - - reg : I2C/SPI address of the device > + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" > + - reg : I2C/SPI address of the device Nothing wrong with correcting alignment, but it shouldn't be in the same patch as a fundamental change lie this. Just adds noise. If that means you first have to introduce the new block missaligned, then fix up the alignment in a follow up patch, then do that as we can then effectively ignore the realignment as obviously correct and focus on the real changes. > > Optional properties: > - - interrupts : The interrupt outputs from the controller > - - interrupt-controller : Marks the device node as an interrupt controller > - - wakeup-source : Marks the input device as wakable > - - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 > - - irq-gpio : If present, which GPIO to use for event IRQ > + - interrupts : The interrupt outputs from the controller > + - interrupt-controller : Marks the device node as an interrupt controller > + - wakeup-source : Marks the input device as wakable > + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 > + - irq-gpio : If present, which GPIO to use for event IRQ > + > +Optional properties for devices with touch and ADC (STMPE811|STMPE610): > + - st,sample-time : ADC conversion time in number of clock. > + 0 -> 36 clocks 4 -> 80 clocks (recommended) > + 1 -> 44 clocks 5 -> 96 clocks > + 2 -> 56 clocks 6 -> 124 clocks > + 3 -> 64 clocks > + - st,mod-12b : ADC Bit mode > + 0 -> 10bit ADC 1 -> 12bit ADC > + - st,ref-sel : ADC reference source > + 0 -> internal 1 -> external > + - st,adc-freq : ADC Clock speed > + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz > + 1 -> 3.25 MHz > > Example: >
On Fri, 23 Nov 2018, Philippe Schenker wrote: > From: Stefan Agner <stefan@agner.ch> > > This adds the devicetree bindings for the STMPE ADC. > > Signed-off-by: Stefan Agner <stefan@agner.ch> > Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> > Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> > --- > > Changes in v3: > - Reformatted documentation for touchscreen to use tabs and have a better > overview of the settings. > - Added note which adc-settings will take precedence. > - changed typo in sample-time setting from 144 clocks to 124 clocks, as stated > in the datasheet. > > Changes in v2: > - Moved the bindings for ADC to the overlying mfd. > - Reformatted for better readability > > .../devicetree/bindings/iio/adc/stmpe-adc.txt | 21 +++++++ > .../bindings/input/touchscreen/stmpe.txt | 60 ++++++++++++------- > .../devicetree/bindings/mfd/stmpe.txt | 28 ++++++--- > 3 files changed, 80 insertions(+), 29 deletions(-) > create mode 100644 Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt [...] > diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt > index c797c05cd3c2..d4408a417193 100644 > --- a/Documentation/devicetree/bindings/mfd/stmpe.txt > +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt > @@ -4,15 +4,29 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, > keypad, touchscreen, adc, pwm, rotator. > > Required properties: > - - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" > - - reg : I2C/SPI address of the device > + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" > + - reg : I2C/SPI address of the device Formatting changes should be completed in a separate patch. Here they only serve to obscure the real changes you have made. Please split the formatting changes out and re-submit.
On Sun, 2018-11-25 at 10:04 +0000, Jonathan Cameron wrote: > On Fri, 23 Nov 2018 15:24:10 +0100 > Philippe Schenker <dev@pschenker.ch> wrote: > > > From: Stefan Agner <stefan@agner.ch> > > > > This adds the devicetree bindings for the STMPE ADC. > > > > Signed-off-by: Stefan Agner <stefan@agner.ch> > > Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> > > Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> > Clearly this will need review from input and mfd. > > I've suggested inline that you split the realignment out to a > separate patch for reviewability reasons. Thank you again Jonathan for your feedback, and of course also all the others! I will split it much more so everything will be much more readable in v4. You suggested again, to use the naming 'adc {'. I know that this is standard naming, but unfortunately, this naming is given by drivers/mfd/stmpe.c (line 1311). What do you suggest to do? break the naming scheme in mfd, or just use 'stmpe_adc {' ? > > > --- > > > > Changes in v3: > > - Reformatted documentation for touchscreen to use tabs and have a better > > overview of the settings. > > - Added note which adc-settings will take precedence. > > - changed typo in sample-time setting from 144 clocks to 124 clocks, as > > stated > > in the datasheet. > > > > Changes in v2: > > - Moved the bindings for ADC to the overlying mfd. > > - Reformatted for better readability > > > > .../devicetree/bindings/iio/adc/stmpe-adc.txt | 21 +++++++ > > .../bindings/input/touchscreen/stmpe.txt | 60 ++++++++++++------- > > .../devicetree/bindings/mfd/stmpe.txt | 28 ++++++--- > > 3 files changed, 80 insertions(+), 29 deletions(-) > > create mode 100644 Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > > > > diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > > b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > > new file mode 100644 > > index 000000000000..480e66422625 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > > @@ -0,0 +1,21 @@ > > +STMPE ADC driver > > +---------------- > > + > > +Required properties: > > + - compatible: "st,stmpe-adc" > > + > > +Optional properties: > > +Note that the ADC is shared with the STMPE touchscreen. ADC related > > settings > > +have to be done in the mfd. > > +- st,norequest-mask: bitmask specifying which ADC channels should _not_ be > > + requestable due to different usage (e.g. touch) > > + > > +Node name must be stmpe_adc and should be child node of stmpe node to > > +which it belongs. > > + > > +Example: > > + > > + stmpe_adc { > > Can we use adc { here to match standard naming? > > > + compatible = "st,stmpe-adc"; > > + st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */ > > + }; > > diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > > b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > > index 127baa31a77a..414586513a02 100644 > > --- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > > +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > > @@ -5,36 +5,52 @@ Required properties: > > - compatible: "st,stmpe-ts" > > > > Optional properties: > > -- st,sample-time: ADC converstion time in number of clock. (0 -> 36 > > clocks, 1 -> > > - 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 > > clocks, 6 > > - -> 144 clocks), recommended is 4. > > -- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) > > -- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external > > - reference) > > -- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> > > 6.5 MHz) > > -- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> > > 4 > > - samples, 3 -> 8 samples) > > -- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, > > 2 -> > > - 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) > > recommended > > - is 3 > > -- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> > > 500 us, 3 > > - -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is > > 2 > > -- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = > > Count of > > - the fractional part) recommended is 7 > > -- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA > > typical 35 > > - mA max, 1 -> 50 mA typical 80 mA max) > > +- st,ave-ctrl : Sample average control > > + 0 -> 1 sample > > + 1 -> 2 samples > > + 2 -> 4 samples > > + 3 -> 8 samples > > +- st,touch-det-delay : Touch detect interrupt delay (recommended is > > 3) > > + 0 -> 10 us 5 -> 5 ms > > + 1 -> 50 us 6 -> 10 ms > > + 2 -> 100 us 7 -> 50 ms > > + 3 -> 500 us > > + 4-> 1 ms > > +- st,settling : Panel driver settling time (recommended is 2) > > + 0 -> 10 us 5 -> 10 ms > > + 1 -> 100 us 6 for 50 ms > > + 2 -> 500 us 7 -> 100 ms > > + 3 -> 1 ms > > + 4 -> 5 ms > > +- st,fraction-z : Length of the fractional part in z > > (recommended is 7) > > + (fraction-z ([0..7]) = Count of the fractional part) > > +- st,i-drive : current limit value of the touchscreen drivers > > + 0 -> 20 mA (typical 35mA max) > > + 1 -> 50 mA (typical 80 mA max) > > + > > +Optional properties common with MFD (deprecated): > > + - st,sample-time : ADC conversion time in number of clock. > > + 0 -> 36 clocks 4 -> 80 clocks > > (recommended) > > + 1 -> 44 clocks 5 -> 96 clocks > > + 2 -> 56 clocks 6 -> 124 clocks > > + 3 -> 64 clocks > > + - st,mod-12b : ADC Bit mode > > + 0 -> 10bit ADC 1 -> 12bit ADC > > + - st,ref-sel : ADC reference source > > + 0 -> internal 1 -> external > > + - st,adc-freq : ADC Clock speed > > + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz > > + 1 -> 3.25 MHz > > > > Node name must be stmpe_touchscreen and should be child node of stmpe node > > to > > which it belongs. > > > > +Note that common ADC settings of stmpe_touchscreen will take precedence. > > + > > Example: > > > > stmpe_touchscreen { > > compatible = "st,stmpe-ts"; > > - st,sample-time = <4>; > > - st,mod-12b = <1>; > > - st,ref-sel = <0>; > > - st,adc-freq = <1>; > > st,ave-ctrl = <1>; > > st,touch-det-delay = <2>; > > st,settling = <2>; > > diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt > > b/Documentation/devicetree/bindings/mfd/stmpe.txt > > index c797c05cd3c2..d4408a417193 100644 > > --- a/Documentation/devicetree/bindings/mfd/stmpe.txt > > +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt > > @@ -4,15 +4,29 @@ STMPE is an MFD device which may expose the following > > inbuilt devices: gpio, > > keypad, touchscreen, adc, pwm, rotator. > > > > Required properties: > > - - compatible : > > "st,stmpe[610|801|811|1600|1601|2401|2403]" > > - - reg : I2C/SPI address of the device > > + - compatible : > > "st,stmpe[610|801|811|1600|1601|2401|2403]" > > + - reg : I2C/SPI address of the device > > Nothing wrong with correcting alignment, but it shouldn't be in the same patch > as a fundamental change lie this. Just adds noise. > > If that means you first have to introduce the new block missaligned, then > fix up the alignment in a follow up patch, then do that as we can then > effectively ignore the realignment as obviously correct and focus on > the real changes. > > > > > Optional properties: > > - - interrupts : The interrupt outputs from the controller > > - - interrupt-controller : Marks the device node as an interrupt > > controller > > - - wakeup-source : Marks the input device as wakable > > - - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, > > 256, 512 and 1024 > > - - irq-gpio : If present, which GPIO to use for event > > IRQ > > + - interrupts : The interrupt outputs from the > > controller > > + - interrupt-controller : Marks the device node as an interrupt > > controller > > + - wakeup-source : Marks the input device as wakable > > + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, > > 128, 256, 512 and 1024 > > + - irq-gpio : If present, which GPIO to use for > > event IRQ > > + > > +Optional properties for devices with touch and ADC (STMPE811|STMPE610): > > + - st,sample-time : ADC conversion time in number of clock. > > + 0 -> 36 clocks 4 -> 80 > > clocks (recommended) > > + 1 -> 44 clocks 5 -> 96 > > clocks > > + 2 -> 56 clocks 6 -> 124 > > clocks > > + 3 -> 64 clocks > > + - st,mod-12b : ADC Bit mode > > + 0 -> 10bit ADC 1 -> 12bit > > ADC > > + - st,ref-sel : ADC reference source > > + 0 -> internal 1 -> > > external > > + - st,adc-freq : ADC Clock speed > > + 0 -> 1.625 MHz 2 || 3 -> > > 6.5 MHz > > + 1 -> 3.25 MHz > > > > Example: > >
On Thu, 06 Dec 2018 16:49:33 +0100 Philippe Schenker <dev@pschenker.ch> wrote: > On Sun, 2018-11-25 at 10:04 +0000, Jonathan Cameron wrote: > > On Fri, 23 Nov 2018 15:24:10 +0100 > > Philippe Schenker <dev@pschenker.ch> wrote: > > > > > From: Stefan Agner <stefan@agner.ch> > > > > > > This adds the devicetree bindings for the STMPE ADC. > > > > > > Signed-off-by: Stefan Agner <stefan@agner.ch> > > > Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> > > > Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> > > Clearly this will need review from input and mfd. > > > > I've suggested inline that you split the realignment out to a > > separate patch for reviewability reasons. > > Thank you again Jonathan for your feedback, and of course also all the others! > > I will split it much more so everything will be much more readable in v4. You > suggested again, to use the naming 'adc {'. I know that this is standard naming, > but unfortunately, this naming is given by drivers/mfd/stmpe.c (line 1311). > What do you suggest to do? break the naming scheme in mfd, or just use > 'stmpe_adc {' ? Leave it as it is, but add a note ideally to say that is the reason. Jonathan > > > > > > --- > > > > > > Changes in v3: > > > - Reformatted documentation for touchscreen to use tabs and have a better > > > overview of the settings. > > > - Added note which adc-settings will take precedence. > > > - changed typo in sample-time setting from 144 clocks to 124 clocks, as > > > stated > > > in the datasheet. > > > > > > Changes in v2: > > > - Moved the bindings for ADC to the overlying mfd. > > > - Reformatted for better readability > > > > > > .../devicetree/bindings/iio/adc/stmpe-adc.txt | 21 +++++++ > > > .../bindings/input/touchscreen/stmpe.txt | 60 ++++++++++++------- > > > .../devicetree/bindings/mfd/stmpe.txt | 28 ++++++--- > > > 3 files changed, 80 insertions(+), 29 deletions(-) > > > create mode 100644 Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > > > > > > diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > > > b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > > > new file mode 100644 > > > index 000000000000..480e66422625 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt > > > @@ -0,0 +1,21 @@ > > > +STMPE ADC driver > > > +---------------- > > > + > > > +Required properties: > > > + - compatible: "st,stmpe-adc" > > > + > > > +Optional properties: > > > +Note that the ADC is shared with the STMPE touchscreen. ADC related > > > settings > > > +have to be done in the mfd. > > > +- st,norequest-mask: bitmask specifying which ADC channels should _not_ be > > > + requestable due to different usage (e.g. touch) > > > + > > > +Node name must be stmpe_adc and should be child node of stmpe node to > > > +which it belongs. > > > + > > > +Example: > > > + > > > + stmpe_adc { > > > > Can we use adc { here to match standard naming? > > > > > + compatible = "st,stmpe-adc"; > > > + st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */ > > > + }; > > > diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > > > b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > > > index 127baa31a77a..414586513a02 100644 > > > --- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > > > +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt > > > @@ -5,36 +5,52 @@ Required properties: > > > - compatible: "st,stmpe-ts" > > > > > > Optional properties: > > > -- st,sample-time: ADC converstion time in number of clock. (0 -> 36 > > > clocks, 1 -> > > > - 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 > > > clocks, 6 > > > - -> 144 clocks), recommended is 4. > > > -- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) > > > -- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external > > > - reference) > > > -- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> > > > 6.5 MHz) > > > -- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> > > > 4 > > > - samples, 3 -> 8 samples) > > > -- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, > > > 2 -> > > > - 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) > > > recommended > > > - is 3 > > > -- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> > > > 500 us, 3 > > > - -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is > > > 2 > > > -- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = > > > Count of > > > - the fractional part) recommended is 7 > > > -- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA > > > typical 35 > > > - mA max, 1 -> 50 mA typical 80 mA max) > > > +- st,ave-ctrl : Sample average control > > > + 0 -> 1 sample > > > + 1 -> 2 samples > > > + 2 -> 4 samples > > > + 3 -> 8 samples > > > +- st,touch-det-delay : Touch detect interrupt delay (recommended is > > > 3) > > > + 0 -> 10 us 5 -> 5 ms > > > + 1 -> 50 us 6 -> 10 ms > > > + 2 -> 100 us 7 -> 50 ms > > > + 3 -> 500 us > > > + 4-> 1 ms > > > +- st,settling : Panel driver settling time (recommended is 2) > > > + 0 -> 10 us 5 -> 10 ms > > > + 1 -> 100 us 6 for 50 ms > > > + 2 -> 500 us 7 -> 100 ms > > > + 3 -> 1 ms > > > + 4 -> 5 ms > > > +- st,fraction-z : Length of the fractional part in z > > > (recommended is 7) > > > + (fraction-z ([0..7]) = Count of the fractional part) > > > +- st,i-drive : current limit value of the touchscreen drivers > > > + 0 -> 20 mA (typical 35mA max) > > > + 1 -> 50 mA (typical 80 mA max) > > > + > > > +Optional properties common with MFD (deprecated): > > > + - st,sample-time : ADC conversion time in number of clock. > > > + 0 -> 36 clocks 4 -> 80 clocks > > > (recommended) > > > + 1 -> 44 clocks 5 -> 96 clocks > > > + 2 -> 56 clocks 6 -> 124 clocks > > > + 3 -> 64 clocks > > > + - st,mod-12b : ADC Bit mode > > > + 0 -> 10bit ADC 1 -> 12bit ADC > > > + - st,ref-sel : ADC reference source > > > + 0 -> internal 1 -> external > > > + - st,adc-freq : ADC Clock speed > > > + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz > > > + 1 -> 3.25 MHz > > > > > > Node name must be stmpe_touchscreen and should be child node of stmpe node > > > to > > > which it belongs. > > > > > > +Note that common ADC settings of stmpe_touchscreen will take precedence. > > > + > > > Example: > > > > > > stmpe_touchscreen { > > > compatible = "st,stmpe-ts"; > > > - st,sample-time = <4>; > > > - st,mod-12b = <1>; > > > - st,ref-sel = <0>; > > > - st,adc-freq = <1>; > > > st,ave-ctrl = <1>; > > > st,touch-det-delay = <2>; > > > st,settling = <2>; > > > diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt > > > b/Documentation/devicetree/bindings/mfd/stmpe.txt > > > index c797c05cd3c2..d4408a417193 100644 > > > --- a/Documentation/devicetree/bindings/mfd/stmpe.txt > > > +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt > > > @@ -4,15 +4,29 @@ STMPE is an MFD device which may expose the following > > > inbuilt devices: gpio, > > > keypad, touchscreen, adc, pwm, rotator. > > > > > > Required properties: > > > - - compatible : > > > "st,stmpe[610|801|811|1600|1601|2401|2403]" > > > - - reg : I2C/SPI address of the device > > > + - compatible : > > > "st,stmpe[610|801|811|1600|1601|2401|2403]" > > > + - reg : I2C/SPI address of the device > > > > Nothing wrong with correcting alignment, but it shouldn't be in the same patch > > as a fundamental change lie this. Just adds noise. > > > > If that means you first have to introduce the new block missaligned, then > > fix up the alignment in a follow up patch, then do that as we can then > > effectively ignore the realignment as obviously correct and focus on > > the real changes. > > > > > > > > Optional properties: > > > - - interrupts : The interrupt outputs from the controller > > > - - interrupt-controller : Marks the device node as an interrupt > > > controller > > > - - wakeup-source : Marks the input device as wakable > > > - - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, > > > 256, 512 and 1024 > > > - - irq-gpio : If present, which GPIO to use for event > > > IRQ > > > + - interrupts : The interrupt outputs from the > > > controller > > > + - interrupt-controller : Marks the device node as an interrupt > > > controller > > > + - wakeup-source : Marks the input device as wakable > > > + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, > > > 128, 256, 512 and 1024 > > > + - irq-gpio : If present, which GPIO to use for > > > event IRQ > > > + > > > +Optional properties for devices with touch and ADC (STMPE811|STMPE610): > > > + - st,sample-time : ADC conversion time in number of clock. > > > + 0 -> 36 clocks 4 -> 80 > > > clocks (recommended) > > > + 1 -> 44 clocks 5 -> 96 > > > clocks > > > + 2 -> 56 clocks 6 -> 124 > > > clocks > > > + 3 -> 64 clocks > > > + - st,mod-12b : ADC Bit mode > > > + 0 -> 10bit ADC 1 -> 12bit > > > ADC > > > + - st,ref-sel : ADC reference source > > > + 0 -> internal 1 -> > > > external > > > + - st,adc-freq : ADC Clock speed > > > + 0 -> 1.625 MHz 2 || 3 -> > > > 6.5 MHz > > > + 1 -> 3.25 MHz > > > > > > Example: > > > >
diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt new file mode 100644 index 000000000000..480e66422625 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt @@ -0,0 +1,21 @@ +STMPE ADC driver +---------------- + +Required properties: + - compatible: "st,stmpe-adc" + +Optional properties: +Note that the ADC is shared with the STMPE touchscreen. ADC related settings +have to be done in the mfd. +- st,norequest-mask: bitmask specifying which ADC channels should _not_ be + requestable due to different usage (e.g. touch) + +Node name must be stmpe_adc and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt index 127baa31a77a..414586513a02 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -5,36 +5,52 @@ Required properties: - compatible: "st,stmpe-ts" Optional properties: -- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> - 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 - -> 144 clocks), recommended is 4. -- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) -- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external - reference) -- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) -- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 - samples, 3 -> 8 samples) -- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> - 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended - is 3 -- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 - -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 -- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of - the fractional part) recommended is 7 -- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 - mA max, 1 -> 50 mA typical 80 mA max) +- st,ave-ctrl : Sample average control + 0 -> 1 sample + 1 -> 2 samples + 2 -> 4 samples + 3 -> 8 samples +- st,touch-det-delay : Touch detect interrupt delay (recommended is 3) + 0 -> 10 us 5 -> 5 ms + 1 -> 50 us 6 -> 10 ms + 2 -> 100 us 7 -> 50 ms + 3 -> 500 us + 4-> 1 ms +- st,settling : Panel driver settling time (recommended is 2) + 0 -> 10 us 5 -> 10 ms + 1 -> 100 us 6 for 50 ms + 2 -> 500 us 7 -> 100 ms + 3 -> 1 ms + 4 -> 5 ms +- st,fraction-z : Length of the fractional part in z (recommended is 7) + (fraction-z ([0..7]) = Count of the fractional part) +- st,i-drive : current limit value of the touchscreen drivers + 0 -> 20 mA (typical 35mA max) + 1 -> 50 mA (typical 80 mA max) + +Optional properties common with MFD (deprecated): + - st,sample-time : ADC conversion time in number of clock. + 0 -> 36 clocks 4 -> 80 clocks (recommended) + 1 -> 44 clocks 5 -> 96 clocks + 2 -> 56 clocks 6 -> 124 clocks + 3 -> 64 clocks + - st,mod-12b : ADC Bit mode + 0 -> 10bit ADC 1 -> 12bit ADC + - st,ref-sel : ADC reference source + 0 -> internal 1 -> external + - st,adc-freq : ADC Clock speed + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz + 1 -> 3.25 MHz Node name must be stmpe_touchscreen and should be child node of stmpe node to which it belongs. +Note that common ADC settings of stmpe_touchscreen will take precedence. + Example: stmpe_touchscreen { compatible = "st,stmpe-ts"; - st,sample-time = <4>; - st,mod-12b = <1>; - st,ref-sel = <0>; - st,adc-freq = <1>; st,ave-ctrl = <1>; st,touch-det-delay = <2>; st,settling = <2>; diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt index c797c05cd3c2..d4408a417193 100644 --- a/Documentation/devicetree/bindings/mfd/stmpe.txt +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -4,15 +4,29 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, keypad, touchscreen, adc, pwm, rotator. Required properties: - - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" - - reg : I2C/SPI address of the device + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" + - reg : I2C/SPI address of the device Optional properties: - - interrupts : The interrupt outputs from the controller - - interrupt-controller : Marks the device node as an interrupt controller - - wakeup-source : Marks the input device as wakable - - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 - - irq-gpio : If present, which GPIO to use for event IRQ + - interrupts : The interrupt outputs from the controller + - interrupt-controller : Marks the device node as an interrupt controller + - wakeup-source : Marks the input device as wakable + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + - irq-gpio : If present, which GPIO to use for event IRQ + +Optional properties for devices with touch and ADC (STMPE811|STMPE610): + - st,sample-time : ADC conversion time in number of clock. + 0 -> 36 clocks 4 -> 80 clocks (recommended) + 1 -> 44 clocks 5 -> 96 clocks + 2 -> 56 clocks 6 -> 124 clocks + 3 -> 64 clocks + - st,mod-12b : ADC Bit mode + 0 -> 10bit ADC 1 -> 12bit ADC + - st,ref-sel : ADC reference source + 0 -> internal 1 -> external + - st,adc-freq : ADC Clock speed + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz + 1 -> 3.25 MHz Example: