| Message ID | 20181113134408.5681-1-marek.behun@nic.cz (mailing list archive) |
|---|---|
| State | RFC |
| Headers | show |
| Series | [RFC] ARM64: dts: marvell: Add DTS file for Turris Mox | expand |
On Tue, Nov 13, 2018 at 02:44:08PM +0100, Marek Behún wrote: > This is a RFC, please do not merge. > > This adds basic support for the Turris Mox board from CZ.NIC. > > Turris Mox is as modular router based on the Armada 3720 SOC (same as > EspressoBin). > > The basic module can be extended by different modules. > When those modules are connected, U-Boot has to let kernel know via > device-tree. Since modules can be connected in different order and > some modules can be connected multiple times (up to three 8-port > switch modules can be connected), using dtb overlays would result in > too files. > > I therefore chose to put all the possible connected devices in one dts > and disable them. If U-Boot finds these modules, it fixes the device > tree accrodginly, by enabling some nodes (setting status to "okay") and > by setting some addresses and references. Given it is a whole hierarchy of nodes, might be cleaner if u-boot removes the whole sub-tree of disable nodes. > For example there are 6 switch nodes - three for 8-port switch module > and three for 4-port switch module. This is because another switch > (either 8-port or 4-port) can be connected to a 8-port switch, in DSA, > and interface names have to be defined (from lan1 to lan24). > > Another way (for defining switch nodes) would have to be either: > - including a file where switch nodes are defined, which would need > #defining lan interface names (and some other things), and #undefing > them after the #include > - defining a macro for switch nodes > - have a separate DTBs for each possible configuration (this would > result in too many DTBs) > - not defining these nodes in device-tree at all, instead creating > them in U-Boot when patching the device-tree (I actually tried this, > but the resulting code in U-Boot was horrible) > > Please let me know if doing it this way is acceptable, or if I should > try something different (and if yes, what?). > > Signed-off-by: Marek Behún <marek.behun@nic.cz> > Cc: Rob Herring <robh@kernel.org> > Cc: linux-kernel@vger.kernel.org > Cc: Gregory CLEMENT <gregory.clement@bootlin.com> > Cc: linux-arm-kernel@lists.infradead.org > Cc: Andrew Lunn <andrew@lunn.ch> > --- > .../arm/marvell/armada-3720-turris-mox.txt | 6 + > MAINTAINERS | 1 + > arch/arm64/boot/dts/marvell/Makefile | 1 + > .../dts/marvell/armada-3720-turris-mox.dts | 838 ++++++++++++++++++ > 4 files changed, 846 insertions(+) > create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt > create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts > > diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt b/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt > new file mode 100644 > index 000000000000..408fc07a9bbf > --- /dev/null > +++ b/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt > @@ -0,0 +1,6 @@ > +CZ.NIC's Turris Mox SOHO router Device Tree Bindings > +---------------------------------------------------- > + > +Required root node property: > + > +compatible: must contain "cznic,turris-mox" This should also contain the SoC compatible. Please add this to where that is defined instead of a new file. > diff --git a/MAINTAINERS b/MAINTAINERS > index f6e60e7f6c11..81b57260b110 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -1348,6 +1348,7 @@ ARM/CZ.NIC TURRIS MOX SUPPORT > M: Marek Behun <marek.behun@nic.cz> > W: http://mox.turris.cz > S: Maintained > +F: arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts > F: include/mfd/moxtet.h > F: drivers/gpio/gpio-moxtet.c > F: drivers/mfd/moxtet.c > diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile > index 5633676fa9d0..51782b31b441 100644 > --- a/arch/arm64/boot/dts/marvell/Makefile > +++ b/arch/arm64/boot/dts/marvell/Makefile > @@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-stb.dtb > # Mvebu SoC Family > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb > +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb > diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts > new file mode 100644 > index 000000000000..1315c59ecef3 > --- /dev/null > +++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts > @@ -0,0 +1,838 @@ > +// SPDX-License-Identifier: GPL-2.0+ or X11 > +/* > + * Device Tree file for CZ.NIC Turris Mox Board > + * 2018 by Marek Behun <marek.behun@nic.cz> > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include "armada-372x.dtsi" > + > +/ { > + model = "CZ.NIC Turris Mox Board"; > + compatible = "cznic,turris-mox", "marvell,armada3720", > + "marvell,armada3710"; > + > + aliases { > + spi0 = &spi0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + memory@0 { > + device_type = "memory"; > + reg = <0x00000000 0x00000000 0x00000000 0x20000000>; > + }; > + > + leds { > + compatible = "gpio-leds"; > + red { > + gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>; > + linux,default-trigger = "heartbeat"; > + }; > + }; > + > + gpio_keys { > + compatible = "gpio-keys"; > + > + reset_button { reset { Don't use '_' in node names. Building with W=2 will tell you this. You chould build with W=1 and fix any warnings this file adds. > + label = "reset"; > + linux,code = <BTN_MISC>; > + gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>; > + debounce-interval = <60>; > + }; > + }; > + > + exp_usb3_vbus: usb3-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb3-vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>; > + }; > + > + usb3_phy: usb3-phy { > + compatible = "usb-nop-xceiv"; > + vcc-supply = <&exp_usb3_vbus>; > + }; > + > + vsdc_reg: vsdc_reg { > + compatible = "regulator-gpio"; > + regulator-name = "vsdc"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + > + gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>; > + gpios-states = <0>; > + states = <1800000 0x1 > + 3300000 0x0>; > + enable-active-high; > + }; > + > + vsdio_reg: vsdio_reg { > + compatible = "regulator-gpio"; > + regulator-name = "vsdio"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + > + gpios = <&gpiosb 22 GPIO_ACTIVE_HIGH>; > + gpios-states = <0>; > + states = <1800000 0x1 > + 3300000 0x0>; > + enable-active-high; > + }; > + > + sdhci1_pwrseq: sdhci1_pwrseq { > + compatible = "mmc-pwrseq-simple"; > + reset-gpios = <&gpionb 19 GPIO_ACTIVE_HIGH>; > + status = "okay"; > + }; > + > + sfp: sfp { > + compatible = "sff,sfp+"; > + i2c-bus = <&i2c0>; > + los-gpio = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>; > + tx-fault-gpio = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>; > + mod-def0-gpio = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>; > + tx-disable-gpio = <&moxtet_sfp 3 GPIO_ACTIVE_HIGH>; > + rate-select0-gpio = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>; > + status = "disabled"; > + }; > +}; > + > +&pinctrl_nb { > + spi_cs1_pins: spi-cs1-pins { > + groups = "spi_cs1"; > + function = "spi"; > + }; > + > + sdio0_pins: sdio0-pins { > + groups = "sdio0"; > + function = "sdio"; > + }; > +}; > + > +&pinctrl_sb { > + sdio_sb_pins: sdio-sb-pins { > + groups = "sdio_sb"; > + function = "sdio"; > + }; > + > + smi_pins: smi-pins { > + groups = "smi"; > + function = "smi"; > + }; > + > + pcie_pins: pcie1-pins { > + groups = "pcie1"; > + function = "gpio"; > + }; > +}; > + > +&i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins>; > + status = "okay"; > + > + rtc@6f { > + compatible = "microchip,mcp7940x"; > + reg = <0x6f>; > + }; > +}; > + > +&pcie0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie_pins>; > + status = "okay"; > + max-link-speed = <2>; > + reset-gpio = <&gpiosb 3 GPIO_ACTIVE_HIGH>; reset-gpios is the preferred form. > + > + /* this shall be enabled by u-boot if the PCIe module is present */ > + status = "disabled"; > +}; > + > +&uart0 { > + status = "okay"; > +}; > + > +ð0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&rgmii_pins>; > + phy-mode = "rgmii-id"; > + phy = <&phy1>; > + status = "okay"; > +}; > + > +ð1 { > + phy-mode = "1000base-x"; > + managed = "in-band-status"; > +}; > + > +&mdio { > + pinctrl-names = "default"; > + pinctrl-0 = <&smi_pins>; > + status = "okay"; > + > + phy1: ethernet-phy@1 { > + reg = <1>; > + }; > + > + switch0@10 { > + compatible = "marvell,mv88e6190"; > + reg = <0x10 0>; > + dsa,member = <0 0>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch0phy1: switch0phy1@1 { > + reg = <0x1>; > + }; > + > + switch0phy2: switch0phy2@2 { > + reg = <0x2>; > + }; > + > + switch0phy3: switch0phy3@3 { > + reg = <0x3>; > + }; > + > + switch0phy4: switch0phy4@4 { > + reg = <0x4>; > + }; > + > + switch0phy5: switch0phy5@5 { > + reg = <0x5>; > + }; > + > + switch0phy6: switch0phy6@6 { > + reg = <0x6>; > + }; > + > + switch0phy7: switch0phy7@7 { > + reg = <0x7>; > + }; > + > + switch0phy8: switch0phy8@8 { > + reg = <0x8>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan1"; > + phy-handle = <&switch0phy1>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan2"; > + phy-handle = <&switch0phy2>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan3"; > + phy-handle = <&switch0phy3>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan4"; > + phy-handle = <&switch0phy4>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "lan5"; > + phy-handle = <&switch0phy5>; > + }; > + > + port@6 { > + reg = <0x6>; > + label = "lan6"; > + phy-handle = <&switch0phy6>; > + }; > + > + port@7 { > + reg = <0x7>; > + label = "lan7"; > + phy-handle = <&switch0phy7>; > + }; > + > + port@8 { > + reg = <0x8>; > + label = "lan8"; > + phy-handle = <&switch0phy8>; > + }; > + > + port@9 { > + reg = <0x9>; > + label = "cpu"; > + ethernet = <ð1>; > + }; > + > + switch0port10: port@a { > + reg = <0xa>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch1port9 &switch2port9>; > + status = "disabled"; > + }; > + > + port-sfp@a { > + reg = <0xa>; > + label = "sfp"; > + sfp = <&sfp>; > + phy-mode = "sgmii"; > + managed = "in-band-status"; > + status = "disabled"; > + }; > + }; > + }; > + > + switch0@2 { > + compatible = "marvell,mv88e6085"; > + reg = <0x2 0>; > + dsa,member = <0 0>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch0phy1_topaz: switch0phy1@11 { > + reg = <0x11>; > + }; > + > + switch0phy2_topaz: switch0phy2@12 { > + reg = <0x12>; > + }; > + > + switch0phy3_topaz: switch0phy3@13 { > + reg = <0x13>; > + }; > + > + switch0phy4_topaz: switch0phy4@14 { > + reg = <0x14>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan1"; > + phy-handle = <&switch0phy1_topaz>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan2"; > + phy-handle = <&switch0phy2_topaz>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan3"; > + phy-handle = <&switch0phy3_topaz>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan4"; > + phy-handle = <&switch0phy4_topaz>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "cpu"; > + ethernet = <ð1>; > + }; > + }; > + }; > + > + switch1@11 { > + compatible = "marvell,mv88e6190"; > + reg = <0x11 0>; > + dsa,member = <0 1>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch1phy1: switch1phy1@1 { > + reg = <0x1>; > + }; > + > + switch1phy2: switch1phy2@2 { > + reg = <0x2>; > + }; > + > + switch1phy3: switch1phy3@3 { > + reg = <0x3>; > + }; > + > + switch1phy4: switch1phy4@4 { > + reg = <0x4>; > + }; > + > + switch1phy5: switch1phy5@5 { > + reg = <0x5>; > + }; > + > + switch1phy6: switch1phy6@6 { > + reg = <0x6>; > + }; > + > + switch1phy7: switch1phy7@7 { > + reg = <0x7>; > + }; > + > + switch1phy8: switch1phy8@8 { > + reg = <0x8>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan9"; > + phy-handle = <&switch1phy1>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan10"; > + phy-handle = <&switch1phy2>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan11"; > + phy-handle = <&switch1phy3>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan12"; > + phy-handle = <&switch1phy4>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "lan13"; > + phy-handle = <&switch1phy5>; > + }; > + > + port@6 { > + reg = <0x6>; > + label = "lan14"; > + phy-handle = <&switch1phy6>; > + }; > + > + port@7 { > + reg = <0x7>; > + label = "lan15"; > + phy-handle = <&switch1phy7>; > + }; > + > + port@8 { > + reg = <0x8>; > + label = "lan16"; > + phy-handle = <&switch1phy8>; > + }; > + > + switch1port9: port@9 { > + reg = <0x9>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch0port10>; > + }; > + > + switch1port10: port@a { > + reg = <0xa>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch2port9>; > + status = "disabled"; > + }; > + > + port-sfp@a { > + reg = <0xa>; > + label = "sfp"; > + sfp = <&sfp>; > + phy-mode = "sgmii"; > + managed = "in-band-status"; > + status = "disabled"; > + }; > + }; > + }; > + > + switch1@2 { Ideally, we shouldn't have this switch0, switch1, etc. > + compatible = "marvell,mv88e6085"; > + reg = <0x2 0>; > + dsa,member = <0 1>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch1phy1_topaz: switch1phy1@11 { > + reg = <0x11>; > + }; > + > + switch1phy2_topaz: switch1phy2@12 { > + reg = <0x12>; > + }; > + > + switch1phy3_topaz: switch1phy3@13 { > + reg = <0x13>; > + }; > + > + switch1phy4_topaz: switch1phy4@14 { > + reg = <0x14>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan9"; > + phy-handle = <&switch1phy1_topaz>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan10"; > + phy-handle = <&switch1phy2_topaz>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan11"; > + phy-handle = <&switch1phy3_topaz>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan12"; > + phy-handle = <&switch1phy4_topaz>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch0port10>; > + }; > + }; > + }; > + > + switch2@12 { > + compatible = "marvell,mv88e6190"; > + reg = <0x12 0>; > + dsa,member = <0 2>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch2phy1: switch2phy1@1 { > + reg = <0x1>; > + }; > + > + switch2phy2: switch2phy2@2 { > + reg = <0x2>; > + }; > + > + switch2phy3: switch2phy3@3 { > + reg = <0x3>; > + }; > + > + switch2phy4: switch2phy4@4 { > + reg = <0x4>; > + }; > + > + switch2phy5: switch2phy5@5 { > + reg = <0x5>; > + }; > + > + switch2phy6: switch2phy6@6 { > + reg = <0x6>; > + }; > + > + switch2phy7: switch2phy7@7 { > + reg = <0x7>; > + }; > + > + switch2phy8: switch2phy8@8 { > + reg = <0x8>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan17"; > + phy-handle = <&switch2phy1>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan18"; > + phy-handle = <&switch2phy2>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan19"; > + phy-handle = <&switch2phy3>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan20"; > + phy-handle = <&switch2phy4>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "lan21"; > + phy-handle = <&switch2phy5>; > + }; > + > + port@6 { > + reg = <0x6>; > + label = "lan22"; > + phy-handle = <&switch2phy6>; > + }; > + > + port@7 { > + reg = <0x7>; > + label = "lan23"; > + phy-handle = <&switch2phy7>; > + }; > + > + port@8 { > + reg = <0x8>; > + label = "lan24"; > + phy-handle = <&switch2phy8>; > + }; > + > + switch2port9: port@9 { > + reg = <0x9>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch1port10 &switch0port10>; > + }; > + > + port-sfp@a { > + reg = <0xa>; > + label = "sfp"; > + sfp = <&sfp>; > + phy-mode = "sgmii"; > + managed = "in-band-status"; > + status = "disabled"; > + }; > + }; > + }; > + > + switch2@2 { > + compatible = "marvell,mv88e6085"; > + reg = <0x2 0>; > + dsa,member = <0 2>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch2phy1_topaz: switch2phy1@11 { > + reg = <0x11>; > + }; > + > + switch2phy2_topaz: switch2phy2@12 { > + reg = <0x12>; > + }; > + > + switch2phy3_topaz: switch2phy3@13 { > + reg = <0x13>; > + }; > + > + switch2phy4_topaz: switch2phy4@14 { > + reg = <0x14>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan17"; > + phy-handle = <&switch2phy1_topaz>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan18"; > + phy-handle = <&switch2phy2_topaz>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan19"; > + phy-handle = <&switch2phy3_topaz>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan20"; > + phy-handle = <&switch2phy4_topaz>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch1port10 &switch0port10>; > + }; > + }; > + }; > + > +}; > + > +&sdhci0 { > + wp-inverted; > + bus-width = <4>; > + cd-gpios = <&gpionb 10 GPIO_ACTIVE_HIGH>; > + vqmmc-supply = <&vsdc_reg>; > + marvell,pad-type = "sd"; > + status = "okay"; > +}; > + > +&sdhci1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&sdio0_pins &sdio_sb_pins>; > + non-removable; > + bus-width = <4>; > + marvell,pad-type = "sd"; > + vqmmc-supply = <&vsdio_reg>; > + mmc-pwrseq = <&sdhci1_pwrseq>; > + status = "okay"; > +}; > + > +&spi0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&spi_quad_pins &spi_cs1_pins>; > + assigned-clocks = <&nb_periph_clk 7>; > + assigned-clock-parents = <&tbg 1>; > + assigned-clock-rates = <20000000>; > + > + spi-flash@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <20000000>; > + > + partition@0 { All these under a 'partitions' node is preferred. > + label = "secure-firmware"; > + reg = <0x0 0x20000>; > + }; > + > + partition@20000 { > + label = "u-boot"; > + reg = <0x20000 0x160000>; > + }; > + > + partition@180000 { > + label = "u-boot-env"; > + reg = <0x180000 0x10000>; > + }; > + > + partition@190000 { > + label = "Rescue system"; > + reg = <0x190000 0x660000>; > + }; > + > + partition@7f0000 { > + label = "dtb"; > + reg = <0x7f0000 0x10000>; > + }; > + }; > + > + moxtet@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "cznic,moxtet"; All this node needs to be documented. > + reg = <1>; > + devrst-gpio = <&gpiosb 2 GPIO_ACTIVE_LOW>; Not documented. reset-gpios is preferred for GPIO reset lines. > + spi-max-frequency = <10000000>; > + spi-cpol; > + spi-cpha; > + > + moxtet_sfp: moxtet-sfp@0 { > + compatible = "cznic,moxtet-gpio"; > + gpio-controller; > + #gpio-cells = <2>; > + reg = <0>; > + moxtet,id = <1>; > + moxtet,input-mask = <0x7>; > + moxtet,output-mask = <0x3>; > + status = "disabled"; > + }; > + }; > +}; > + > +&usb2 { > + status = "okay"; > +}; > + > +&usb3 { > + status = "okay"; > + usb-phy = <&usb3_phy>; > +}; > -- > 2.18.1 >
Hi Rob On Tue, 4 Dec 2018 14:37:06 -0600 Rob Herring <robh@kernel.org> wrote: > > + > > + switch1@2 { > > Ideally, we shouldn't have this switch0, switch1, etc. I can rename peridot switches (switch0@10, switch1@11, switch2@12 to swtich@10, switch@11, switch@12), but I cannot rename Topaz to switch@2. Topaz always has MDIO address 2, because there can be only one, but it can be connected either directly or after the first or second peridot. Therefore I have three different nodes, each describing different connection to the previous switch/cpu. How should I rename it? Marek
Hi Marek, On mar., nov. 13 2018, Marek Behún <marek.behun@nic.cz> wrote: > This is a RFC, please do not merge. > > This adds basic support for the Turris Mox board from CZ.NIC. > > Turris Mox is as modular router based on the Armada 3720 SOC (same as > EspressoBin). > > The basic module can be extended by different modules. > When those modules are connected, U-Boot has to let kernel know via > device-tree. Since modules can be connected in different order and > some modules can be connected multiple times (up to three 8-port > switch modules can be connected), using dtb overlays would result in > too files. What do you mean by too many files? The dtb overlays seems really matches your situation. Usually we have one dtb part by module and then we mix them together. Gregory > > I therefore chose to put all the possible connected devices in one dts > and disable them. If U-Boot finds these modules, it fixes the device > tree accrodginly, by enabling some nodes (setting status to "okay") and > by setting some addresses and references. > > For example there are 6 switch nodes - three for 8-port switch module > and three for 4-port switch module. This is because another switch > (either 8-port or 4-port) can be connected to a 8-port switch, in DSA, > and interface names have to be defined (from lan1 to lan24). > > Another way (for defining switch nodes) would have to be either: > - including a file where switch nodes are defined, which would need > #defining lan interface names (and some other things), and #undefing > them after the #include > - defining a macro for switch nodes > - have a separate DTBs for each possible configuration (this would > result in too many DTBs) > - not defining these nodes in device-tree at all, instead creating > them in U-Boot when patching the device-tree (I actually tried this, > but the resulting code in U-Boot was horrible) > > Please let me know if doing it this way is acceptable, or if I should > try something different (and if yes, what?). > > Signed-off-by: Marek Behún <marek.behun@nic.cz> > Cc: Rob Herring <robh@kernel.org> > Cc: linux-kernel@vger.kernel.org > Cc: Gregory CLEMENT <gregory.clement@bootlin.com> > Cc: linux-arm-kernel@lists.infradead.org > Cc: Andrew Lunn <andrew@lunn.ch> > --- > .../arm/marvell/armada-3720-turris-mox.txt | 6 + > MAINTAINERS | 1 + > arch/arm64/boot/dts/marvell/Makefile | 1 + > .../dts/marvell/armada-3720-turris-mox.dts | 838 ++++++++++++++++++ > 4 files changed, 846 insertions(+) > create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt > create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts > > diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt b/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt > new file mode 100644 > index 000000000000..408fc07a9bbf > --- /dev/null > +++ b/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt > @@ -0,0 +1,6 @@ > +CZ.NIC's Turris Mox SOHO router Device Tree Bindings > +---------------------------------------------------- > + > +Required root node property: > + > +compatible: must contain "cznic,turris-mox" > diff --git a/MAINTAINERS b/MAINTAINERS > index f6e60e7f6c11..81b57260b110 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -1348,6 +1348,7 @@ ARM/CZ.NIC TURRIS MOX SUPPORT > M: Marek Behun <marek.behun@nic.cz> > W: http://mox.turris.cz > S: Maintained > +F: arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts > F: include/mfd/moxtet.h > F: drivers/gpio/gpio-moxtet.c > F: drivers/mfd/moxtet.c > diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile > index 5633676fa9d0..51782b31b441 100644 > --- a/arch/arm64/boot/dts/marvell/Makefile > +++ b/arch/arm64/boot/dts/marvell/Makefile > @@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-stb.dtb > # Mvebu SoC Family > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb > +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb > diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts > new file mode 100644 > index 000000000000..1315c59ecef3 > --- /dev/null > +++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts > @@ -0,0 +1,838 @@ > +// SPDX-License-Identifier: GPL-2.0+ or X11 > +/* > + * Device Tree file for CZ.NIC Turris Mox Board > + * 2018 by Marek Behun <marek.behun@nic.cz> > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include "armada-372x.dtsi" > + > +/ { > + model = "CZ.NIC Turris Mox Board"; > + compatible = "cznic,turris-mox", "marvell,armada3720", > + "marvell,armada3710"; > + > + aliases { > + spi0 = &spi0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + memory@0 { > + device_type = "memory"; > + reg = <0x00000000 0x00000000 0x00000000 0x20000000>; > + }; > + > + leds { > + compatible = "gpio-leds"; > + red { > + gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>; > + linux,default-trigger = "heartbeat"; > + }; > + }; > + > + gpio_keys { > + compatible = "gpio-keys"; > + > + reset_button { > + label = "reset"; > + linux,code = <BTN_MISC>; > + gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>; > + debounce-interval = <60>; > + }; > + }; > + > + exp_usb3_vbus: usb3-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb3-vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>; > + }; > + > + usb3_phy: usb3-phy { > + compatible = "usb-nop-xceiv"; > + vcc-supply = <&exp_usb3_vbus>; > + }; > + > + vsdc_reg: vsdc_reg { > + compatible = "regulator-gpio"; > + regulator-name = "vsdc"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + > + gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>; > + gpios-states = <0>; > + states = <1800000 0x1 > + 3300000 0x0>; > + enable-active-high; > + }; > + > + vsdio_reg: vsdio_reg { > + compatible = "regulator-gpio"; > + regulator-name = "vsdio"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + > + gpios = <&gpiosb 22 GPIO_ACTIVE_HIGH>; > + gpios-states = <0>; > + states = <1800000 0x1 > + 3300000 0x0>; > + enable-active-high; > + }; > + > + sdhci1_pwrseq: sdhci1_pwrseq { > + compatible = "mmc-pwrseq-simple"; > + reset-gpios = <&gpionb 19 GPIO_ACTIVE_HIGH>; > + status = "okay"; > + }; > + > + sfp: sfp { > + compatible = "sff,sfp+"; > + i2c-bus = <&i2c0>; > + los-gpio = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>; > + tx-fault-gpio = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>; > + mod-def0-gpio = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>; > + tx-disable-gpio = <&moxtet_sfp 3 GPIO_ACTIVE_HIGH>; > + rate-select0-gpio = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>; > + status = "disabled"; > + }; > +}; > + > +&pinctrl_nb { > + spi_cs1_pins: spi-cs1-pins { > + groups = "spi_cs1"; > + function = "spi"; > + }; > + > + sdio0_pins: sdio0-pins { > + groups = "sdio0"; > + function = "sdio"; > + }; > +}; > + > +&pinctrl_sb { > + sdio_sb_pins: sdio-sb-pins { > + groups = "sdio_sb"; > + function = "sdio"; > + }; > + > + smi_pins: smi-pins { > + groups = "smi"; > + function = "smi"; > + }; > + > + pcie_pins: pcie1-pins { > + groups = "pcie1"; > + function = "gpio"; > + }; > +}; > + > +&i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins>; > + status = "okay"; > + > + rtc@6f { > + compatible = "microchip,mcp7940x"; > + reg = <0x6f>; > + }; > +}; > + > +&pcie0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie_pins>; > + status = "okay"; > + max-link-speed = <2>; > + reset-gpio = <&gpiosb 3 GPIO_ACTIVE_HIGH>; > + > + /* this shall be enabled by u-boot if the PCIe module is present */ > + status = "disabled"; > +}; > + > +&uart0 { > + status = "okay"; > +}; > + > +ð0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&rgmii_pins>; > + phy-mode = "rgmii-id"; > + phy = <&phy1>; > + status = "okay"; > +}; > + > +ð1 { > + phy-mode = "1000base-x"; > + managed = "in-band-status"; > +}; > + > +&mdio { > + pinctrl-names = "default"; > + pinctrl-0 = <&smi_pins>; > + status = "okay"; > + > + phy1: ethernet-phy@1 { > + reg = <1>; > + }; > + > + switch0@10 { > + compatible = "marvell,mv88e6190"; > + reg = <0x10 0>; > + dsa,member = <0 0>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch0phy1: switch0phy1@1 { > + reg = <0x1>; > + }; > + > + switch0phy2: switch0phy2@2 { > + reg = <0x2>; > + }; > + > + switch0phy3: switch0phy3@3 { > + reg = <0x3>; > + }; > + > + switch0phy4: switch0phy4@4 { > + reg = <0x4>; > + }; > + > + switch0phy5: switch0phy5@5 { > + reg = <0x5>; > + }; > + > + switch0phy6: switch0phy6@6 { > + reg = <0x6>; > + }; > + > + switch0phy7: switch0phy7@7 { > + reg = <0x7>; > + }; > + > + switch0phy8: switch0phy8@8 { > + reg = <0x8>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan1"; > + phy-handle = <&switch0phy1>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan2"; > + phy-handle = <&switch0phy2>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan3"; > + phy-handle = <&switch0phy3>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan4"; > + phy-handle = <&switch0phy4>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "lan5"; > + phy-handle = <&switch0phy5>; > + }; > + > + port@6 { > + reg = <0x6>; > + label = "lan6"; > + phy-handle = <&switch0phy6>; > + }; > + > + port@7 { > + reg = <0x7>; > + label = "lan7"; > + phy-handle = <&switch0phy7>; > + }; > + > + port@8 { > + reg = <0x8>; > + label = "lan8"; > + phy-handle = <&switch0phy8>; > + }; > + > + port@9 { > + reg = <0x9>; > + label = "cpu"; > + ethernet = <ð1>; > + }; > + > + switch0port10: port@a { > + reg = <0xa>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch1port9 &switch2port9>; > + status = "disabled"; > + }; > + > + port-sfp@a { > + reg = <0xa>; > + label = "sfp"; > + sfp = <&sfp>; > + phy-mode = "sgmii"; > + managed = "in-band-status"; > + status = "disabled"; > + }; > + }; > + }; > + > + switch0@2 { > + compatible = "marvell,mv88e6085"; > + reg = <0x2 0>; > + dsa,member = <0 0>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch0phy1_topaz: switch0phy1@11 { > + reg = <0x11>; > + }; > + > + switch0phy2_topaz: switch0phy2@12 { > + reg = <0x12>; > + }; > + > + switch0phy3_topaz: switch0phy3@13 { > + reg = <0x13>; > + }; > + > + switch0phy4_topaz: switch0phy4@14 { > + reg = <0x14>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan1"; > + phy-handle = <&switch0phy1_topaz>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan2"; > + phy-handle = <&switch0phy2_topaz>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan3"; > + phy-handle = <&switch0phy3_topaz>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan4"; > + phy-handle = <&switch0phy4_topaz>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "cpu"; > + ethernet = <ð1>; > + }; > + }; > + }; > + > + switch1@11 { > + compatible = "marvell,mv88e6190"; > + reg = <0x11 0>; > + dsa,member = <0 1>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch1phy1: switch1phy1@1 { > + reg = <0x1>; > + }; > + > + switch1phy2: switch1phy2@2 { > + reg = <0x2>; > + }; > + > + switch1phy3: switch1phy3@3 { > + reg = <0x3>; > + }; > + > + switch1phy4: switch1phy4@4 { > + reg = <0x4>; > + }; > + > + switch1phy5: switch1phy5@5 { > + reg = <0x5>; > + }; > + > + switch1phy6: switch1phy6@6 { > + reg = <0x6>; > + }; > + > + switch1phy7: switch1phy7@7 { > + reg = <0x7>; > + }; > + > + switch1phy8: switch1phy8@8 { > + reg = <0x8>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan9"; > + phy-handle = <&switch1phy1>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan10"; > + phy-handle = <&switch1phy2>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan11"; > + phy-handle = <&switch1phy3>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan12"; > + phy-handle = <&switch1phy4>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "lan13"; > + phy-handle = <&switch1phy5>; > + }; > + > + port@6 { > + reg = <0x6>; > + label = "lan14"; > + phy-handle = <&switch1phy6>; > + }; > + > + port@7 { > + reg = <0x7>; > + label = "lan15"; > + phy-handle = <&switch1phy7>; > + }; > + > + port@8 { > + reg = <0x8>; > + label = "lan16"; > + phy-handle = <&switch1phy8>; > + }; > + > + switch1port9: port@9 { > + reg = <0x9>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch0port10>; > + }; > + > + switch1port10: port@a { > + reg = <0xa>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch2port9>; > + status = "disabled"; > + }; > + > + port-sfp@a { > + reg = <0xa>; > + label = "sfp"; > + sfp = <&sfp>; > + phy-mode = "sgmii"; > + managed = "in-band-status"; > + status = "disabled"; > + }; > + }; > + }; > + > + switch1@2 { > + compatible = "marvell,mv88e6085"; > + reg = <0x2 0>; > + dsa,member = <0 1>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch1phy1_topaz: switch1phy1@11 { > + reg = <0x11>; > + }; > + > + switch1phy2_topaz: switch1phy2@12 { > + reg = <0x12>; > + }; > + > + switch1phy3_topaz: switch1phy3@13 { > + reg = <0x13>; > + }; > + > + switch1phy4_topaz: switch1phy4@14 { > + reg = <0x14>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan9"; > + phy-handle = <&switch1phy1_topaz>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan10"; > + phy-handle = <&switch1phy2_topaz>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan11"; > + phy-handle = <&switch1phy3_topaz>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan12"; > + phy-handle = <&switch1phy4_topaz>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch0port10>; > + }; > + }; > + }; > + > + switch2@12 { > + compatible = "marvell,mv88e6190"; > + reg = <0x12 0>; > + dsa,member = <0 2>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch2phy1: switch2phy1@1 { > + reg = <0x1>; > + }; > + > + switch2phy2: switch2phy2@2 { > + reg = <0x2>; > + }; > + > + switch2phy3: switch2phy3@3 { > + reg = <0x3>; > + }; > + > + switch2phy4: switch2phy4@4 { > + reg = <0x4>; > + }; > + > + switch2phy5: switch2phy5@5 { > + reg = <0x5>; > + }; > + > + switch2phy6: switch2phy6@6 { > + reg = <0x6>; > + }; > + > + switch2phy7: switch2phy7@7 { > + reg = <0x7>; > + }; > + > + switch2phy8: switch2phy8@8 { > + reg = <0x8>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan17"; > + phy-handle = <&switch2phy1>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan18"; > + phy-handle = <&switch2phy2>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan19"; > + phy-handle = <&switch2phy3>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan20"; > + phy-handle = <&switch2phy4>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "lan21"; > + phy-handle = <&switch2phy5>; > + }; > + > + port@6 { > + reg = <0x6>; > + label = "lan22"; > + phy-handle = <&switch2phy6>; > + }; > + > + port@7 { > + reg = <0x7>; > + label = "lan23"; > + phy-handle = <&switch2phy7>; > + }; > + > + port@8 { > + reg = <0x8>; > + label = "lan24"; > + phy-handle = <&switch2phy8>; > + }; > + > + switch2port9: port@9 { > + reg = <0x9>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch1port10 &switch0port10>; > + }; > + > + port-sfp@a { > + reg = <0xa>; > + label = "sfp"; > + sfp = <&sfp>; > + phy-mode = "sgmii"; > + managed = "in-band-status"; > + status = "disabled"; > + }; > + }; > + }; > + > + switch2@2 { > + compatible = "marvell,mv88e6085"; > + reg = <0x2 0>; > + dsa,member = <0 2>; > + interrupt-parent = <&gpiosb>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch2phy1_topaz: switch2phy1@11 { > + reg = <0x11>; > + }; > + > + switch2phy2_topaz: switch2phy2@12 { > + reg = <0x12>; > + }; > + > + switch2phy3_topaz: switch2phy3@13 { > + reg = <0x13>; > + }; > + > + switch2phy4_topaz: switch2phy4@14 { > + reg = <0x14>; > + }; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <0x1>; > + label = "lan17"; > + phy-handle = <&switch2phy1_topaz>; > + }; > + > + port@2 { > + reg = <0x2>; > + label = "lan18"; > + phy-handle = <&switch2phy2_topaz>; > + }; > + > + port@3 { > + reg = <0x3>; > + label = "lan19"; > + phy-handle = <&switch2phy3_topaz>; > + }; > + > + port@4 { > + reg = <0x4>; > + label = "lan20"; > + phy-handle = <&switch2phy4_topaz>; > + }; > + > + port@5 { > + reg = <0x5>; > + label = "dsa"; > + phy-mode = "2500base-x"; > + link = <&switch1port10 &switch0port10>; > + }; > + }; > + }; > + > +}; > + > +&sdhci0 { > + wp-inverted; > + bus-width = <4>; > + cd-gpios = <&gpionb 10 GPIO_ACTIVE_HIGH>; > + vqmmc-supply = <&vsdc_reg>; > + marvell,pad-type = "sd"; > + status = "okay"; > +}; > + > +&sdhci1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&sdio0_pins &sdio_sb_pins>; > + non-removable; > + bus-width = <4>; > + marvell,pad-type = "sd"; > + vqmmc-supply = <&vsdio_reg>; > + mmc-pwrseq = <&sdhci1_pwrseq>; > + status = "okay"; > +}; > + > +&spi0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&spi_quad_pins &spi_cs1_pins>; > + assigned-clocks = <&nb_periph_clk 7>; > + assigned-clock-parents = <&tbg 1>; > + assigned-clock-rates = <20000000>; > + > + spi-flash@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <20000000>; > + > + partition@0 { > + label = "secure-firmware"; > + reg = <0x0 0x20000>; > + }; > + > + partition@20000 { > + label = "u-boot"; > + reg = <0x20000 0x160000>; > + }; > + > + partition@180000 { > + label = "u-boot-env"; > + reg = <0x180000 0x10000>; > + }; > + > + partition@190000 { > + label = "Rescue system"; > + reg = <0x190000 0x660000>; > + }; > + > + partition@7f0000 { > + label = "dtb"; > + reg = <0x7f0000 0x10000>; > + }; > + }; > + > + moxtet@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "cznic,moxtet"; > + reg = <1>; > + devrst-gpio = <&gpiosb 2 GPIO_ACTIVE_LOW>; > + spi-max-frequency = <10000000>; > + spi-cpol; > + spi-cpha; > + > + moxtet_sfp: moxtet-sfp@0 { > + compatible = "cznic,moxtet-gpio"; > + gpio-controller; > + #gpio-cells = <2>; > + reg = <0>; > + moxtet,id = <1>; > + moxtet,input-mask = <0x7>; > + moxtet,output-mask = <0x3>; > + status = "disabled"; > + }; > + }; > +}; > + > +&usb2 { > + status = "okay"; > +}; > + > +&usb3 { > + status = "okay"; > + usb-phy = <&usb3_phy>; > +}; > -- > 2.18.1 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Fri, 18 Jan 2019 15:35:35 +0100 Gregory CLEMENT <gregory.clement@bootlin.com> wrote: > > The basic module can be extended by different modules. > > When those modules are connected, U-Boot has to let kernel know via > > device-tree. Since modules can be connected in different order and > > some modules can be connected multiple times (up to three 8-port > > switch modules can be connected), using dtb overlays would result in > > too files. > > What do you mean by too many files? > > The dtb overlays seems really matches your situation. > Usually we have one dtb part by module and then we mix them together. > > Gregory Hi Gregory, the problem is that in some cases here some even if you have the same module, some parameters have to be different depending on which position the module is in the topology and what type of module is before it. For example up to three switch modules can be connected one after another, and although physically they are the same, their dtb parameters (MDIO address and whether they are connected to CPU or another switch module) are different. So if I wanter to use overlays without dtb modification from u-boot, I would have to have three overlays for Peridot module, for topologies: peridot peridot-peridot peridot-peridot-peridot three for Topaz module: topaz peridot-topaz peridot-peridot-topaz and four for SFP module: sfp peridot-sfp peridot-peridot-sfp peridot-peridot-peridot-sfp For the PCIe and USB module this is not the case, only one overlay for each. But I thought (and still think) that in this case it is more elegant to just enable the modules in U-Boot than to use so many different overlays. And since I already thought up this solution for SFP and switch modules, I used it for the PCIe and USB modules as well, instead of mixing overlays there. I am of course willing to rewrite this to use overlays, if you guys are unwilling to merge it done this way, but I think this solution is better. Also, I would like to have the dts definitions for all modules officially supported by Mox to have in the kernel, and if this was done via overlays, it would not be merged, or am I wrong? Are there overlay dts sources for some device in the kernel? Marek
diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt b/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt new file mode 100644 index 000000000000..408fc07a9bbf --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt @@ -0,0 +1,6 @@ +CZ.NIC's Turris Mox SOHO router Device Tree Bindings +---------------------------------------------------- + +Required root node property: + +compatible: must contain "cznic,turris-mox" diff --git a/MAINTAINERS b/MAINTAINERS index f6e60e7f6c11..81b57260b110 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1348,6 +1348,7 @@ ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <marek.behun@nic.cz> W: http://mox.turris.cz S: Maintained +F: arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts F: include/mfd/moxtet.h F: drivers/gpio/gpio-moxtet.c F: drivers/mfd/moxtet.c diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index 5633676fa9d0..51782b31b441 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-stb.dtb # Mvebu SoC Family dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts new file mode 100644 index 000000000000..1315c59ecef3 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts @@ -0,0 +1,838 @@ +// SPDX-License-Identifier: GPL-2.0+ or X11 +/* + * Device Tree file for CZ.NIC Turris Mox Board + * 2018 by Marek Behun <marek.behun@nic.cz> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "armada-372x.dtsi" + +/ { + model = "CZ.NIC Turris Mox Board"; + compatible = "cznic,turris-mox", "marvell,armada3720", + "marvell,armada3710"; + + aliases { + spi0 = &spi0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x00000000 0x00000000 0x20000000>; + }; + + leds { + compatible = "gpio-leds"; + red { + gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + reset_button { + label = "reset"; + linux,code = <BTN_MISC>; + gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + exp_usb3_vbus: usb3-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb3-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>; + }; + + usb3_phy: usb3-phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <&exp_usb3_vbus>; + }; + + vsdc_reg: vsdc_reg { + compatible = "regulator-gpio"; + regulator-name = "vsdc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + + gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + states = <1800000 0x1 + 3300000 0x0>; + enable-active-high; + }; + + vsdio_reg: vsdio_reg { + compatible = "regulator-gpio"; + regulator-name = "vsdio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + + gpios = <&gpiosb 22 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + states = <1800000 0x1 + 3300000 0x0>; + enable-active-high; + }; + + sdhci1_pwrseq: sdhci1_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpionb 19 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + sfp: sfp { + compatible = "sff,sfp+"; + i2c-bus = <&i2c0>; + los-gpio = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&moxtet_sfp 3 GPIO_ACTIVE_HIGH>; + rate-select0-gpio = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; +}; + +&pinctrl_nb { + spi_cs1_pins: spi-cs1-pins { + groups = "spi_cs1"; + function = "spi"; + }; + + sdio0_pins: sdio0-pins { + groups = "sdio0"; + function = "sdio"; + }; +}; + +&pinctrl_sb { + sdio_sb_pins: sdio-sb-pins { + groups = "sdio_sb"; + function = "sdio"; + }; + + smi_pins: smi-pins { + groups = "smi"; + function = "smi"; + }; + + pcie_pins: pcie1-pins { + groups = "pcie1"; + function = "gpio"; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + status = "okay"; + + rtc@6f { + compatible = "microchip,mcp7940x"; + reg = <0x6f>; + }; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie_pins>; + status = "okay"; + max-link-speed = <2>; + reset-gpio = <&gpiosb 3 GPIO_ACTIVE_HIGH>; + + /* this shall be enabled by u-boot if the PCIe module is present */ + status = "disabled"; +}; + +&uart0 { + status = "okay"; +}; + +ð0 { + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + phy-mode = "rgmii-id"; + phy = <&phy1>; + status = "okay"; +}; + +ð1 { + phy-mode = "1000base-x"; + managed = "in-band-status"; +}; + +&mdio { + pinctrl-names = "default"; + pinctrl-0 = <&smi_pins>; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + + switch0@10 { + compatible = "marvell,mv88e6190"; + reg = <0x10 0>; + dsa,member = <0 0>; + interrupt-parent = <&gpiosb>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + status = "disabled"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch0phy1: switch0phy1@1 { + reg = <0x1>; + }; + + switch0phy2: switch0phy2@2 { + reg = <0x2>; + }; + + switch0phy3: switch0phy3@3 { + reg = <0x3>; + }; + + switch0phy4: switch0phy4@4 { + reg = <0x4>; + }; + + switch0phy5: switch0phy5@5 { + reg = <0x5>; + }; + + switch0phy6: switch0phy6@6 { + reg = <0x6>; + }; + + switch0phy7: switch0phy7@7 { + reg = <0x7>; + }; + + switch0phy8: switch0phy8@8 { + reg = <0x8>; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <0x1>; + label = "lan1"; + phy-handle = <&switch0phy1>; + }; + + port@2 { + reg = <0x2>; + label = "lan2"; + phy-handle = <&switch0phy2>; + }; + + port@3 { + reg = <0x3>; + label = "lan3"; + phy-handle = <&switch0phy3>; + }; + + port@4 { + reg = <0x4>; + label = "lan4"; + phy-handle = <&switch0phy4>; + }; + + port@5 { + reg = <0x5>; + label = "lan5"; + phy-handle = <&switch0phy5>; + }; + + port@6 { + reg = <0x6>; + label = "lan6"; + phy-handle = <&switch0phy6>; + }; + + port@7 { + reg = <0x7>; + label = "lan7"; + phy-handle = <&switch0phy7>; + }; + + port@8 { + reg = <0x8>; + label = "lan8"; + phy-handle = <&switch0phy8>; + }; + + port@9 { + reg = <0x9>; + label = "cpu"; + ethernet = <ð1>; + }; + + switch0port10: port@a { + reg = <0xa>; + label = "dsa"; + phy-mode = "2500base-x"; + link = <&switch1port9 &switch2port9>; + status = "disabled"; + }; + + port-sfp@a { + reg = <0xa>; + label = "sfp"; + sfp = <&sfp>; + phy-mode = "sgmii"; + managed = "in-band-status"; + status = "disabled"; + }; + }; + }; + + switch0@2 { + compatible = "marvell,mv88e6085"; + reg = <0x2 0>; + dsa,member = <0 0>; + interrupt-parent = <&gpiosb>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + status = "disabled"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch0phy1_topaz: switch0phy1@11 { + reg = <0x11>; + }; + + switch0phy2_topaz: switch0phy2@12 { + reg = <0x12>; + }; + + switch0phy3_topaz: switch0phy3@13 { + reg = <0x13>; + }; + + switch0phy4_topaz: switch0phy4@14 { + reg = <0x14>; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <0x1>; + label = "lan1"; + phy-handle = <&switch0phy1_topaz>; + }; + + port@2 { + reg = <0x2>; + label = "lan2"; + phy-handle = <&switch0phy2_topaz>; + }; + + port@3 { + reg = <0x3>; + label = "lan3"; + phy-handle = <&switch0phy3_topaz>; + }; + + port@4 { + reg = <0x4>; + label = "lan4"; + phy-handle = <&switch0phy4_topaz>; + }; + + port@5 { + reg = <0x5>; + label = "cpu"; + ethernet = <ð1>; + }; + }; + }; + + switch1@11 { + compatible = "marvell,mv88e6190"; + reg = <0x11 0>; + dsa,member = <0 1>; + interrupt-parent = <&gpiosb>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + status = "disabled"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch1phy1: switch1phy1@1 { + reg = <0x1>; + }; + + switch1phy2: switch1phy2@2 { + reg = <0x2>; + }; + + switch1phy3: switch1phy3@3 { + reg = <0x3>; + }; + + switch1phy4: switch1phy4@4 { + reg = <0x4>; + }; + + switch1phy5: switch1phy5@5 { + reg = <0x5>; + }; + + switch1phy6: switch1phy6@6 { + reg = <0x6>; + }; + + switch1phy7: switch1phy7@7 { + reg = <0x7>; + }; + + switch1phy8: switch1phy8@8 { + reg = <0x8>; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <0x1>; + label = "lan9"; + phy-handle = <&switch1phy1>; + }; + + port@2 { + reg = <0x2>; + label = "lan10"; + phy-handle = <&switch1phy2>; + }; + + port@3 { + reg = <0x3>; + label = "lan11"; + phy-handle = <&switch1phy3>; + }; + + port@4 { + reg = <0x4>; + label = "lan12"; + phy-handle = <&switch1phy4>; + }; + + port@5 { + reg = <0x5>; + label = "lan13"; + phy-handle = <&switch1phy5>; + }; + + port@6 { + reg = <0x6>; + label = "lan14"; + phy-handle = <&switch1phy6>; + }; + + port@7 { + reg = <0x7>; + label = "lan15"; + phy-handle = <&switch1phy7>; + }; + + port@8 { + reg = <0x8>; + label = "lan16"; + phy-handle = <&switch1phy8>; + }; + + switch1port9: port@9 { + reg = <0x9>; + label = "dsa"; + phy-mode = "2500base-x"; + link = <&switch0port10>; + }; + + switch1port10: port@a { + reg = <0xa>; + label = "dsa"; + phy-mode = "2500base-x"; + link = <&switch2port9>; + status = "disabled"; + }; + + port-sfp@a { + reg = <0xa>; + label = "sfp"; + sfp = <&sfp>; + phy-mode = "sgmii"; + managed = "in-band-status"; + status = "disabled"; + }; + }; + }; + + switch1@2 { + compatible = "marvell,mv88e6085"; + reg = <0x2 0>; + dsa,member = <0 1>; + interrupt-parent = <&gpiosb>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + status = "disabled"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch1phy1_topaz: switch1phy1@11 { + reg = <0x11>; + }; + + switch1phy2_topaz: switch1phy2@12 { + reg = <0x12>; + }; + + switch1phy3_topaz: switch1phy3@13 { + reg = <0x13>; + }; + + switch1phy4_topaz: switch1phy4@14 { + reg = <0x14>; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <0x1>; + label = "lan9"; + phy-handle = <&switch1phy1_topaz>; + }; + + port@2 { + reg = <0x2>; + label = "lan10"; + phy-handle = <&switch1phy2_topaz>; + }; + + port@3 { + reg = <0x3>; + label = "lan11"; + phy-handle = <&switch1phy3_topaz>; + }; + + port@4 { + reg = <0x4>; + label = "lan12"; + phy-handle = <&switch1phy4_topaz>; + }; + + port@5 { + reg = <0x5>; + label = "dsa"; + phy-mode = "2500base-x"; + link = <&switch0port10>; + }; + }; + }; + + switch2@12 { + compatible = "marvell,mv88e6190"; + reg = <0x12 0>; + dsa,member = <0 2>; + interrupt-parent = <&gpiosb>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + status = "disabled"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch2phy1: switch2phy1@1 { + reg = <0x1>; + }; + + switch2phy2: switch2phy2@2 { + reg = <0x2>; + }; + + switch2phy3: switch2phy3@3 { + reg = <0x3>; + }; + + switch2phy4: switch2phy4@4 { + reg = <0x4>; + }; + + switch2phy5: switch2phy5@5 { + reg = <0x5>; + }; + + switch2phy6: switch2phy6@6 { + reg = <0x6>; + }; + + switch2phy7: switch2phy7@7 { + reg = <0x7>; + }; + + switch2phy8: switch2phy8@8 { + reg = <0x8>; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <0x1>; + label = "lan17"; + phy-handle = <&switch2phy1>; + }; + + port@2 { + reg = <0x2>; + label = "lan18"; + phy-handle = <&switch2phy2>; + }; + + port@3 { + reg = <0x3>; + label = "lan19"; + phy-handle = <&switch2phy3>; + }; + + port@4 { + reg = <0x4>; + label = "lan20"; + phy-handle = <&switch2phy4>; + }; + + port@5 { + reg = <0x5>; + label = "lan21"; + phy-handle = <&switch2phy5>; + }; + + port@6 { + reg = <0x6>; + label = "lan22"; + phy-handle = <&switch2phy6>; + }; + + port@7 { + reg = <0x7>; + label = "lan23"; + phy-handle = <&switch2phy7>; + }; + + port@8 { + reg = <0x8>; + label = "lan24"; + phy-handle = <&switch2phy8>; + }; + + switch2port9: port@9 { + reg = <0x9>; + label = "dsa"; + phy-mode = "2500base-x"; + link = <&switch1port10 &switch0port10>; + }; + + port-sfp@a { + reg = <0xa>; + label = "sfp"; + sfp = <&sfp>; + phy-mode = "sgmii"; + managed = "in-band-status"; + status = "disabled"; + }; + }; + }; + + switch2@2 { + compatible = "marvell,mv88e6085"; + reg = <0x2 0>; + dsa,member = <0 2>; + interrupt-parent = <&gpiosb>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + status = "disabled"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch2phy1_topaz: switch2phy1@11 { + reg = <0x11>; + }; + + switch2phy2_topaz: switch2phy2@12 { + reg = <0x12>; + }; + + switch2phy3_topaz: switch2phy3@13 { + reg = <0x13>; + }; + + switch2phy4_topaz: switch2phy4@14 { + reg = <0x14>; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <0x1>; + label = "lan17"; + phy-handle = <&switch2phy1_topaz>; + }; + + port@2 { + reg = <0x2>; + label = "lan18"; + phy-handle = <&switch2phy2_topaz>; + }; + + port@3 { + reg = <0x3>; + label = "lan19"; + phy-handle = <&switch2phy3_topaz>; + }; + + port@4 { + reg = <0x4>; + label = "lan20"; + phy-handle = <&switch2phy4_topaz>; + }; + + port@5 { + reg = <0x5>; + label = "dsa"; + phy-mode = "2500base-x"; + link = <&switch1port10 &switch0port10>; + }; + }; + }; + +}; + +&sdhci0 { + wp-inverted; + bus-width = <4>; + cd-gpios = <&gpionb 10 GPIO_ACTIVE_HIGH>; + vqmmc-supply = <&vsdc_reg>; + marvell,pad-type = "sd"; + status = "okay"; +}; + +&sdhci1 { + pinctrl-names = "default"; + pinctrl-0 = <&sdio0_pins &sdio_sb_pins>; + non-removable; + bus-width = <4>; + marvell,pad-type = "sd"; + vqmmc-supply = <&vsdio_reg>; + mmc-pwrseq = <&sdhci1_pwrseq>; + status = "okay"; +}; + +&spi0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi_quad_pins &spi_cs1_pins>; + assigned-clocks = <&nb_periph_clk 7>; + assigned-clock-parents = <&tbg 1>; + assigned-clock-rates = <20000000>; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + + partition@0 { + label = "secure-firmware"; + reg = <0x0 0x20000>; + }; + + partition@20000 { + label = "u-boot"; + reg = <0x20000 0x160000>; + }; + + partition@180000 { + label = "u-boot-env"; + reg = <0x180000 0x10000>; + }; + + partition@190000 { + label = "Rescue system"; + reg = <0x190000 0x660000>; + }; + + partition@7f0000 { + label = "dtb"; + reg = <0x7f0000 0x10000>; + }; + }; + + moxtet@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "cznic,moxtet"; + reg = <1>; + devrst-gpio = <&gpiosb 2 GPIO_ACTIVE_LOW>; + spi-max-frequency = <10000000>; + spi-cpol; + spi-cpha; + + moxtet_sfp: moxtet-sfp@0 { + compatible = "cznic,moxtet-gpio"; + gpio-controller; + #gpio-cells = <2>; + reg = <0>; + moxtet,id = <1>; + moxtet,input-mask = <0x7>; + moxtet,output-mask = <0x3>; + status = "disabled"; + }; + }; +}; + +&usb2 { + status = "okay"; +}; + +&usb3 { + status = "okay"; + usb-phy = <&usb3_phy>; +};
This is a RFC, please do not merge. This adds basic support for the Turris Mox board from CZ.NIC. Turris Mox is as modular router based on the Armada 3720 SOC (same as EspressoBin). The basic module can be extended by different modules. When those modules are connected, U-Boot has to let kernel know via device-tree. Since modules can be connected in different order and some modules can be connected multiple times (up to three 8-port switch modules can be connected), using dtb overlays would result in too files. I therefore chose to put all the possible connected devices in one dts and disable them. If U-Boot finds these modules, it fixes the device tree accrodginly, by enabling some nodes (setting status to "okay") and by setting some addresses and references. For example there are 6 switch nodes - three for 8-port switch module and three for 4-port switch module. This is because another switch (either 8-port or 4-port) can be connected to a 8-port switch, in DSA, and interface names have to be defined (from lan1 to lan24). Another way (for defining switch nodes) would have to be either: - including a file where switch nodes are defined, which would need #defining lan interface names (and some other things), and #undefing them after the #include - defining a macro for switch nodes - have a separate DTBs for each possible configuration (this would result in too many DTBs) - not defining these nodes in device-tree at all, instead creating them in U-Boot when patching the device-tree (I actually tried this, but the resulting code in U-Boot was horrible) Please let me know if doing it this way is acceptable, or if I should try something different (and if yes, what?). Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Rob Herring <robh@kernel.org> Cc: linux-kernel@vger.kernel.org Cc: Gregory CLEMENT <gregory.clement@bootlin.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Andrew Lunn <andrew@lunn.ch> --- .../arm/marvell/armada-3720-turris-mox.txt | 6 + MAINTAINERS | 1 + arch/arm64/boot/dts/marvell/Makefile | 1 + .../dts/marvell/armada-3720-turris-mox.dts | 838 ++++++++++++++++++ 4 files changed, 846 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts