@@ -457,6 +457,14 @@ config REGULATOR_MAX77620
chip to control Step-Down DC-DC and LDOs. Say Y here to
enable the regulator driver.
+config REGULATOR_MAX77650
+ tristate "Maxim MAX77650/77651 regulator support"
+ depends on MFD_MAX77650
+ help
+ Regulator driver for MAX77650/77651 PMIC from Maxim
+ Semiconductor. This device has a SIMO with three independent
+ power rails and an LDO.
+
config REGULATOR_MAX8649
tristate "Maxim 8649 voltage regulator"
depends on I2C
@@ -60,6 +60,7 @@ obj-$(CONFIG_REGULATOR_LTC3676) += ltc3676.o
obj-$(CONFIG_REGULATOR_MAX14577) += max14577-regulator.o
obj-$(CONFIG_REGULATOR_MAX1586) += max1586.o
obj-$(CONFIG_REGULATOR_MAX77620) += max77620-regulator.o
+obj-$(CONFIG_REGULATOR_MAX77650) += max77650-regulator.o
obj-$(CONFIG_REGULATOR_MAX8649) += max8649.o
obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o
obj-$(CONFIG_REGULATOR_MAX8907) += max8907-regulator.o
new file mode 100644
@@ -0,0 +1,537 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 BayLibre SAS
+ * Author: Bartosz Golaszewski <bgolaszewski@baylibre.com>
+ *
+ * Regulator driver for MAXIM 77650/77651 charger/power-supply.
+ */
+
+#include <linux/i2c.h>
+#include <linux/mfd/max77650.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+#define MAX77650_REGULATOR_EN_CTRL_MASK GENMASK(3, 0)
+#define MAX77650_REGULATOR_EN_CTRL_BITS(_reg) \
+ ((_reg) & MAX77650_REGULATOR_EN_CTRL_MASK)
+#define MAX77650_REGULATOR_ENABLED GENMASK(2, 1)
+#define MAX77650_REGULATOR_DISABLED BIT(2)
+
+#define MAX77650_REGULATOR_V_LDO_MASK GENMASK(6, 0)
+#define MAX77650_REGULATOR_V_SBB_MASK GENMASK(5, 0)
+
+#define MAX77650_REGULATOR_AD_MASK BIT(3)
+#define MAX77650_REGULATOR_AD_DISABLED 0x00
+#define MAX77650_REGULATOR_AD_ENABLED BIT(3)
+
+#define MAX77650_REGULATOR_CURR_LIM_MASK GENMASK(7, 6)
+#define MAX77650_REGULATOR_CURR_LIM_BITS(_reg) \
+ (((_reg) & MAX77650_REGULATOR_CURR_LIM_MASK) >> 6)
+#define MAX77650_REGULATOR_CURR_LIM_SHIFT(_val) ((_val) << 6)
+
+enum {
+ MAX77650_REGULATOR_ID_LDO = 0,
+ MAX77650_REGULATOR_ID_SBB0,
+ MAX77650_REGULATOR_ID_SBB1,
+ MAX77650_REGULATOR_ID_SBB2,
+ MAX77650_REGULATOR_NUM_REGULATORS,
+};
+
+struct max77650_regulator_desc {
+ struct regulator_desc desc;
+ unsigned int regA;
+ unsigned int regB;
+};
+
+static const u32 max77651_sbb1_regulator_volt_table[] = {
+ 2400000, 3200000, 4000000, 4800000,
+ 2450000, 3250000, 4050000, 4850000,
+ 2500000, 3300000, 4100000, 4900000,
+ 2550000, 3350000, 4150000, 4950000,
+ 2600000, 3400000, 4200000, 5000000,
+ 2650000, 3450000, 4250000, 5050000,
+ 2700000, 3500000, 4300000, 5100000,
+ 2750000, 3550000, 4350000, 5150000,
+ 2800000, 3600000, 4400000, 5200000,
+ 2850000, 3650000, 4450000, 5250000,
+ 2900000, 3700000, 4500000, 0,
+ 2950000, 3750000, 4550000, 0,
+ 3000000, 3800000, 4600000, 0,
+ 3050000, 3850000, 4650000, 0,
+ 3100000, 3900000, 4700000, 0,
+ 3150000, 3950000, 4750000, 0,
+};
+
+#define MAX77651_REGULATOR_SBB1_SEL_DEC(_val) \
+ (((_val & 0x3c) >> 2) | ((_val & 0x03) << 4))
+#define MAX77651_REGULATOR_SBB1_SEL_ENC(_val) \
+ (((_val & 0x30) >> 4) | ((_val & 0x0f) << 2))
+
+#define MAX77650_REGULATOR_SBB1_SEL_DECR(_val) \
+ do { \
+ _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \
+ _val--; \
+ _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \
+ } while (0)
+
+#define MAX77650_REGULATOR_SBB1_SEL_INCR(_val) \
+ do { \
+ _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \
+ _val++; \
+ _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \
+ } while (0)
+
+static const int max77650_current_limit_table[] = {
+ 1000000, 866000, 707000, 500000,
+};
+
+static int max77650_regulator_is_enabled(struct regulator_dev *rdev)
+{
+ struct max77650_regulator_desc *rdesc;
+ struct regmap *map;
+ int val, rv, en;
+
+ rdesc = rdev_get_drvdata(rdev);
+ map = rdev_get_regmap(rdev);
+
+ rv = regmap_read(map, rdesc->regB, &val);
+ if (rv)
+ return rv;
+
+ en = MAX77650_REGULATOR_EN_CTRL_BITS(val);
+
+ return en != MAX77650_REGULATOR_DISABLED;
+}
+
+static int max77650_regulator_enable(struct regulator_dev *rdev)
+{
+ struct max77650_regulator_desc *rdesc;
+ struct regmap *map;
+
+ rdesc = rdev_get_drvdata(rdev);
+ map = rdev_get_regmap(rdev);
+
+ return regmap_update_bits(map, rdesc->regB,
+ MAX77650_REGULATOR_EN_CTRL_MASK,
+ MAX77650_REGULATOR_ENABLED);
+}
+
+static int max77650_regulator_disable(struct regulator_dev *rdev)
+{
+ struct max77650_regulator_desc *rdesc;
+ struct regmap *map;
+
+ rdesc = rdev_get_drvdata(rdev);
+ map = rdev_get_regmap(rdev);
+
+ return regmap_update_bits(map, rdesc->regB,
+ MAX77650_REGULATOR_EN_CTRL_MASK,
+ MAX77650_REGULATOR_DISABLED);
+}
+
+static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
+ unsigned int sel)
+{
+ int rv = 0, curr, diff;
+ bool ascending;
+
+ /*
+ * If the regulator is disabled, we can program the desired
+ * voltage right away.
+ */
+ if (!max77650_regulator_is_enabled(rdev))
+ return regulator_set_voltage_sel_regmap(rdev, sel);
+
+ /*
+ * Otherwise we need to manually ramp the output voltage up/down
+ * one step at a time.
+ */
+
+ curr = regulator_get_voltage_sel_regmap(rdev);
+ if (curr < 0)
+ return curr;
+
+ diff = curr - sel;
+ if (diff == 0)
+ return 0; /* Already there. */
+ else if (diff > 0)
+ ascending = false;
+ else
+ ascending = true;
+
+ /*
+ * Make sure we'll get to the right voltage and break the loop even if
+ * the selector equals 0.
+ */
+ for (ascending ? curr++ : curr--;; ascending ? curr++ : curr--) {
+ rv = regulator_set_voltage_sel_regmap(rdev, curr);
+ if (rv)
+ return rv;
+
+ if (curr == sel)
+ break;
+ }
+
+ return 0;
+}
+
+/*
+ * Special case: non-linear voltage table for max77651 SBB1 - software
+ * must ensure the voltage is ramped in 50mV increments.
+ */
+static int max77651_regulator_sbb1_set_voltage_sel(struct regulator_dev *rdev,
+ unsigned int sel)
+{
+ int rv = 0, curr, vcurr, vdest, vdiff;
+
+ /*
+ * If the regulator is disabled, we can program the desired
+ * voltage right away.
+ */
+ if (!max77650_regulator_is_enabled(rdev))
+ return regulator_set_voltage_sel_regmap(rdev, sel);
+
+ curr = regulator_get_voltage_sel_regmap(rdev);
+ if (curr < 0)
+ return curr;
+
+ if (curr == sel)
+ return 0; /* Already there. */
+
+ vcurr = max77651_sbb1_regulator_volt_table[curr];
+ vdest = max77651_sbb1_regulator_volt_table[sel];
+ vdiff = vcurr - vdest;
+
+ for (;;) {
+ if (vdiff > 0)
+ MAX77650_REGULATOR_SBB1_SEL_DECR(curr);
+ else
+ MAX77650_REGULATOR_SBB1_SEL_INCR(curr);
+
+ rv = regulator_set_voltage_sel_regmap(rdev, curr);
+ if (rv)
+ return rv;
+
+ if (curr == sel)
+ break;
+ };
+
+ return 0;
+}
+
+static int max77650_regulator_get_current_limit(struct regulator_dev *rdev)
+{
+ struct max77650_regulator_desc *rdesc;
+ struct regmap *map;
+ int val, rv, limit;
+
+ rdesc = rdev_get_drvdata(rdev);
+ map = rdev_get_regmap(rdev);
+
+ rv = regmap_read(map, rdesc->regA, &val);
+ if (rv)
+ return rv;
+
+ limit = MAX77650_REGULATOR_CURR_LIM_BITS(val);
+
+ return max77650_current_limit_table[limit];
+}
+
+static int max77650_regulator_set_current_limit(struct regulator_dev *rdev,
+ int min_uA, int max_uA)
+{
+ struct max77650_regulator_desc *rdesc;
+ struct regmap *map;
+ int rv, i, limit;
+
+ rdesc = rdev_get_drvdata(rdev);
+ map = rdev_get_regmap(rdev);
+
+ for (i = 0; i < ARRAY_SIZE(max77650_current_limit_table); i++) {
+ limit = max77650_current_limit_table[i];
+
+ if (limit >= min_uA && limit <= max_uA) {
+ rv = regmap_update_bits(map, rdesc->regA,
+ MAX77650_REGULATOR_CURR_LIM_MASK,
+ MAX77650_REGULATOR_CURR_LIM_SHIFT(i));
+ if (rv)
+ return rv;
+ }
+ }
+
+ return -EINVAL;
+}
+
+static const struct regulator_ops max77650_regulator_LDO_ops = {
+ .is_enabled = max77650_regulator_is_enabled,
+ .enable = max77650_regulator_enable,
+ .disable = max77650_regulator_disable,
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = max77650_regulator_set_voltage_sel,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+};
+
+static const struct regulator_ops max77650_regulator_SBB_ops = {
+ .is_enabled = max77650_regulator_is_enabled,
+ .enable = max77650_regulator_enable,
+ .disable = max77650_regulator_disable,
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = max77650_regulator_set_voltage_sel,
+ .get_current_limit = max77650_regulator_get_current_limit,
+ .set_current_limit = max77650_regulator_set_current_limit,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+};
+
+/* Special case for max77651 SBB1 - non-linear voltage mapping. */
+static const struct regulator_ops max77651_SBB1_regulator_ops = {
+ .is_enabled = max77650_regulator_is_enabled,
+ .enable = max77650_regulator_enable,
+ .disable = max77650_regulator_disable,
+ .list_voltage = regulator_list_voltage_table,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = max77651_regulator_sbb1_set_voltage_sel,
+ .get_current_limit = max77650_regulator_get_current_limit,
+ .set_current_limit = max77650_regulator_set_current_limit,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+};
+
+static struct max77650_regulator_desc max77650_LDO_desc = {
+ .desc = {
+ .name = "ldo",
+ .of_match = of_match_ptr("ldo"),
+ .regulators_node = of_match_ptr("regulators"),
+ .supply_name = "in-ldo",
+ .id = MAX77650_REGULATOR_ID_LDO,
+ .ops = &max77650_regulator_LDO_ops,
+ .min_uV = 1350000,
+ .uV_step = 12500,
+ .n_voltages = 128,
+ .vsel_mask = MAX77650_REGULATOR_V_LDO_MASK,
+ .vsel_reg = MAX77650_REG_CNFG_LDO_A,
+ .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED,
+ .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED,
+ .active_discharge_mask = MAX77650_REGULATOR_AD_MASK,
+ .active_discharge_reg = MAX77650_REG_CNFG_LDO_B,
+ .enable_time = 100,
+ .type = REGULATOR_VOLTAGE,
+ },
+ .regA = MAX77650_REG_CNFG_LDO_A,
+ .regB = MAX77650_REG_CNFG_LDO_B,
+};
+
+static struct max77650_regulator_desc max77650_SBB0_desc = {
+ .desc = {
+ .name = "sbb0",
+ .of_match = of_match_ptr("sbb0"),
+ .regulators_node = of_match_ptr("regulators"),
+ .supply_name = "in-sbb0",
+ .id = MAX77650_REGULATOR_ID_SBB0,
+ .ops = &max77650_regulator_SBB_ops,
+ .min_uV = 800000,
+ .uV_step = 25000,
+ .n_voltages = 64,
+ .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK,
+ .vsel_reg = MAX77650_REG_CNFG_SBB0_A,
+ .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED,
+ .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED,
+ .active_discharge_mask = MAX77650_REGULATOR_AD_MASK,
+ .active_discharge_reg = MAX77650_REG_CNFG_SBB0_B,
+ .enable_time = 100,
+ .type = REGULATOR_VOLTAGE,
+ },
+ .regA = MAX77650_REG_CNFG_SBB0_A,
+ .regB = MAX77650_REG_CNFG_SBB0_B,
+};
+
+static struct max77650_regulator_desc max77650_SBB1_desc = {
+ .desc = {
+ .name = "sbb1",
+ .of_match = of_match_ptr("sbb1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .supply_name = "in-sbb1",
+ .id = MAX77650_REGULATOR_ID_SBB1,
+ .ops = &max77650_regulator_SBB_ops,
+ .min_uV = 800000,
+ .uV_step = 12500,
+ .n_voltages = 64,
+ .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK,
+ .vsel_reg = MAX77650_REG_CNFG_SBB1_A,
+ .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED,
+ .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED,
+ .active_discharge_mask = MAX77650_REGULATOR_AD_MASK,
+ .active_discharge_reg = MAX77650_REG_CNFG_SBB1_B,
+ .enable_time = 100,
+ .type = REGULATOR_VOLTAGE,
+ },
+ .regA = MAX77650_REG_CNFG_SBB1_A,
+ .regB = MAX77650_REG_CNFG_SBB1_B,
+};
+
+static struct max77650_regulator_desc max77651_SBB1_desc = {
+ .desc = {
+ .name = "sbb1",
+ .of_match = of_match_ptr("sbb1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .supply_name = "in-sbb1",
+ .id = MAX77650_REGULATOR_ID_SBB1,
+ .ops = &max77651_SBB1_regulator_ops,
+ .volt_table = max77651_sbb1_regulator_volt_table,
+ .n_voltages = ARRAY_SIZE(max77651_sbb1_regulator_volt_table),
+ .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK,
+ .vsel_reg = MAX77650_REG_CNFG_SBB1_A,
+ .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED,
+ .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED,
+ .active_discharge_mask = MAX77650_REGULATOR_AD_MASK,
+ .active_discharge_reg = MAX77650_REG_CNFG_SBB1_B,
+ .enable_time = 100,
+ .type = REGULATOR_VOLTAGE,
+ },
+ .regA = MAX77650_REG_CNFG_SBB1_A,
+ .regB = MAX77650_REG_CNFG_SBB1_B,
+};
+
+static struct max77650_regulator_desc max77650_SBB2_desc = {
+ .desc = {
+ .name = "sbb2",
+ .of_match = of_match_ptr("sbb2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .supply_name = "in-sbb0",
+ .id = MAX77650_REGULATOR_ID_SBB2,
+ .ops = &max77650_regulator_SBB_ops,
+ .min_uV = 800000,
+ .uV_step = 50000,
+ .n_voltages = 64,
+ .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK,
+ .vsel_reg = MAX77650_REG_CNFG_SBB2_A,
+ .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED,
+ .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED,
+ .active_discharge_mask = MAX77650_REGULATOR_AD_MASK,
+ .active_discharge_reg = MAX77650_REG_CNFG_SBB2_B,
+ .enable_time = 100,
+ .type = REGULATOR_VOLTAGE,
+ },
+ .regA = MAX77650_REG_CNFG_SBB2_A,
+ .regB = MAX77650_REG_CNFG_SBB2_B,
+};
+
+static struct max77650_regulator_desc max77651_SBB2_desc = {
+ .desc = {
+ .name = "sbb2",
+ .of_match = of_match_ptr("sbb2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .supply_name = "in-sbb0",
+ .id = MAX77650_REGULATOR_ID_SBB2,
+ .ops = &max77650_regulator_SBB_ops,
+ .min_uV = 2400000,
+ .uV_step = 50000,
+ .n_voltages = 64,
+ .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK,
+ .vsel_reg = MAX77650_REG_CNFG_SBB2_A,
+ .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED,
+ .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED,
+ .active_discharge_mask = MAX77650_REGULATOR_AD_MASK,
+ .active_discharge_reg = MAX77650_REG_CNFG_SBB2_B,
+ .enable_time = 100,
+ .type = REGULATOR_VOLTAGE,
+ },
+ .regA = MAX77650_REG_CNFG_SBB2_A,
+ .regB = MAX77650_REG_CNFG_SBB2_B,
+};
+
+static int max77650_regulator_probe(struct platform_device *pdev)
+{
+ struct max77650_regulator_desc **rdescs;
+ struct max77650_regulator_desc *rdesc;
+ struct regulator_init_data *init_data;
+ struct regulator_config config = { };
+ struct device *dev, *parent;
+ struct regulator_dev *rdev;
+ struct device_node *child;
+ struct regmap *map;
+ unsigned int val;
+ int i, rv;
+
+ dev = &pdev->dev;
+ parent = dev->parent;
+
+ if (!dev->of_node)
+ dev->of_node = parent->of_node;
+
+ rdescs = devm_kcalloc(dev, MAX77650_REGULATOR_NUM_REGULATORS,
+ sizeof(*rdescs), GFP_KERNEL);
+ if (!rdescs)
+ return -ENOMEM;
+
+ map = dev_get_regmap(parent, NULL);
+ if (!map)
+ return -ENODEV;
+
+ rv = regmap_read(map, MAX77650_REG_CID, &val);
+ if (rv)
+ return rv;
+
+ rdescs[MAX77650_REGULATOR_ID_LDO] = &max77650_LDO_desc;
+ rdescs[MAX77650_REGULATOR_ID_SBB0] = &max77650_SBB0_desc;
+
+ switch (MAX77650_CID_BITS(val)) {
+ case MAX77650_CID_77650A:
+ case MAX77650_CID_77650C:
+ rdescs[MAX77650_REGULATOR_ID_SBB1] = &max77650_SBB1_desc;
+ rdescs[MAX77650_REGULATOR_ID_SBB2] = &max77650_SBB2_desc;
+ break;
+ case MAX77650_CID_77651A:
+ case MAX77650_CID_77651B:
+ rdescs[MAX77650_REGULATOR_ID_SBB1] = &max77651_SBB1_desc;
+ rdescs[MAX77650_REGULATOR_ID_SBB2] = &max77651_SBB2_desc;
+ break;
+ default:
+ return -ENODEV;
+ }
+
+ config.dev = dev;
+
+ for (i = 0; i < MAX77650_REGULATOR_NUM_REGULATORS; i++) {
+ rdesc = rdescs[i];
+ config.driver_data = rdesc;
+ config.of_node = NULL;
+ config.init_data = NULL;
+
+ for_each_child_of_node(dev->of_node, child) {
+ if (!of_node_name_eq(child, rdesc->desc.name))
+ continue;
+
+ init_data = of_get_regulator_init_data(dev, child,
+ &rdesc->desc);
+ if (!init_data)
+ return -ENOMEM;
+
+ config.of_node = child;
+ config.init_data = init_data;
+ }
+
+ rdev = devm_regulator_register(dev, &rdesc->desc, &config);
+ if (IS_ERR(rdev))
+ return PTR_ERR(rdev);
+ }
+
+ return 0;
+}
+
+static struct platform_driver max77650_regulator_driver = {
+ .driver = {
+ .name = "max77650-regulator",
+ },
+ .probe = max77650_regulator_probe,
+};
+module_platform_driver(max77650_regulator_driver);
+
+MODULE_DESCRIPTION("MAXIM 77650/77651 regulator driver");
+MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@baylibre.com>");
+MODULE_LICENSE("GPL");