@@ -8,6 +8,7 @@
#include <dt-bindings/power/imx8mq-power.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
#include "imx8mq-pinfunc.h"
/ {
@@ -89,6 +90,7 @@
reg = <0x0>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ #cooling-cells = <2>;
};
A53_1: cpu@1 {
@@ -97,6 +99,7 @@
reg = <0x1>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ #cooling-cells = <2>;
};
A53_2: cpu@2 {
@@ -105,6 +108,7 @@
reg = <0x2>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ #cooling-cells = <2>;
};
A53_3: cpu@3 {
@@ -113,6 +117,7 @@
reg = <0x3>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ #cooling-cells = <2>;
};
A53_L2: l2-cache0 {
@@ -210,6 +215,119 @@
#interrupt-cells = <2>;
};
+ tmu: tmu@30260000 {
+ compatible = "fsl,imx8mq-tmu";
+ reg = <0x30260000 0x10000>;
+ interrupt = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+ little-endian;
+ fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>;
+ fsl,tmu-calibration = <0x00000000 0x00000023
+ 0x00000001 0x00000029
+ 0x00000002 0x0000002f
+ 0x00000003 0x00000035
+ 0x00000004 0x0000003d
+ 0x00000005 0x00000043
+ 0x00000006 0x0000004b
+ 0x00000007 0x00000051
+ 0x00000008 0x00000057
+ 0x00000009 0x0000005f
+ 0x0000000a 0x00000067
+ 0x0000000b 0x0000006f
+
+ 0x00010000 0x0000001b
+ 0x00010001 0x00000023
+ 0x00010002 0x0000002b
+ 0x00010003 0x00000033
+ 0x00010004 0x0000003b
+ 0x00010005 0x00000043
+ 0x00010006 0x0000004b
+ 0x00010007 0x00000055
+ 0x00010008 0x0000005d
+ 0x00010009 0x00000067
+ 0x0001000a 0x00000070
+
+ 0x00020000 0x00000017
+ 0x00020001 0x00000023
+ 0x00020002 0x0000002d
+ 0x00020003 0x00000037
+ 0x00020004 0x00000041
+ 0x00020005 0x0000004b
+ 0x00020006 0x00000057
+ 0x00020007 0x00000063
+ 0x00020008 0x0000006f
+
+ 0x00030000 0x00000015
+ 0x00030001 0x00000021
+ 0x00030002 0x0000002d
+ 0x00030003 0x00000039
+ 0x00030004 0x00000045
+ 0x00030005 0x00000053
+ 0x00030006 0x0000005f
+ 0x00030007 0x00000071>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ thermal-zones {
+ cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu 0>;
+
+ trips {
+ cpu_alert: cpu-alert {
+ temperature = <80000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-crit {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert>;
+ cooling-device =
+ <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ gpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu 1>;
+
+ trips {
+ gpu-crit {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ vpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu 2>;
+
+ trips {
+ vpu-crit {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
wdog1: watchdog@30280000 {
compatible = "fsl,imx8mq-wdt", "fsl,imx21-wdt";
reg = <0x30280000 0x10000>;
Add the imx8mq TMU (Thermal management unit) nodes for CPU, GPU, and VPU. Changes since v2: Updated alert and critical temps for commercial parts. Fixed node names. Changes since v1: Removed references to multi sensor patch. Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> --- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 118 ++++++++++++++++++++++ 1 file changed, 118 insertions(+)