diff mbox series

[v4,5/6] usb: roles: add USB Type-B GPIO connector driver

Message ID 1556261237-13823-6-git-send-email-chunfeng.yun@mediatek.com (mailing list archive)
State Superseded
Headers show
Series add USB Type-B GPIO connector driver | expand

Commit Message

Chunfeng Yun (云春峰) April 26, 2019, 6:47 a.m. UTC 
Due to the requirement of usb-connector.txt binding, the old way
using extcon to support USB Dual-Role switch is now deprecated
when use Type-B connector.
This patch introduces a driver of Type-B connector which typically
uses an input GPIO to detect USB ID pin, and try to replace the
function provided by extcon-usb-gpio driver

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v4 changes:
  1. remove linux/gpio.h suggested by Linus
  2. put node when error happens

v3 changes:
  1. treat bype-B connector as a virtual device;
  2. change file name again

v2 changes:
  1. file name is changed
  2. use new compatible
---
 drivers/usb/roles/Kconfig           |  11 +
 drivers/usb/roles/Makefile          |   1 +
 drivers/usb/roles/typeb-conn-gpio.c | 305 ++++++++++++++++++++++++++++
 3 files changed, 317 insertions(+)
 create mode 100644 drivers/usb/roles/typeb-conn-gpio.c

Comments

Biju Das April 26, 2019, 9:22 a.m. UTC | #1 
Hi Chunfeng Yun,

Thanks for the patch.

> Subject: [PATCH v4 5/6] usb: roles: add USB Type-B GPIO connector driver
> 
> Due to the requirement of usb-connector.txt binding, the old way using
> extcon to support USB Dual-Role switch is now deprecated when use Type-B
> connector.
> This patch introduces a driver of Type-B connector which typically uses an
> input GPIO to detect USB ID pin, and try to replace the function provided by
> extcon-usb-gpio driver
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v4 changes:
>   1. remove linux/gpio.h suggested by Linus
>   2. put node when error happens
> 
> v3 changes:
>   1. treat bype-B connector as a virtual device;
>   2. change file name again
> 
> v2 changes:
>   1. file name is changed
>   2. use new compatible
> ---
>  drivers/usb/roles/Kconfig           |  11 +
>  drivers/usb/roles/Makefile          |   1 +
>  drivers/usb/roles/typeb-conn-gpio.c | 305
> ++++++++++++++++++++++++++++
>  3 files changed, 317 insertions(+)
>  create mode 100644 drivers/usb/roles/typeb-conn-gpio.c
> 
> diff --git a/drivers/usb/roles/Kconfig b/drivers/usb/roles/Kconfig index
> f8b31aa67526..d1156e18a81a 100644
> --- a/drivers/usb/roles/Kconfig
> +++ b/drivers/usb/roles/Kconfig
> @@ -26,4 +26,15 @@ config USB_ROLES_INTEL_XHCI
>  	  To compile the driver as a module, choose M here: the module will
>  	  be called intel-xhci-usb-role-switch.
> 
> +config TYPEB_CONN_GPIO
> +	tristate "USB Type-B GPIO Connector"
> +	depends on GPIOLIB
> +	help
> +	  The driver supports USB role switch between host and device via
> GPIO
> +	  based USB cable detection, used typically if an input GPIO is used
> +	  to detect USB ID pin.
> +
> +	  To compile the driver as a module, choose M here: the module will
> +	  be called typeb-conn-gpio.ko
> +
>  endif # USB_ROLE_SWITCH
> diff --git a/drivers/usb/roles/Makefile b/drivers/usb/roles/Makefile index
> 757a7d2797eb..5d5620d9d113 100644
> --- a/drivers/usb/roles/Makefile
> +++ b/drivers/usb/roles/Makefile
> @@ -3,3 +3,4 @@
>  obj-$(CONFIG_USB_ROLE_SWITCH)		+= roles.o
>  roles-y					:= class.o
>  obj-$(CONFIG_USB_ROLES_INTEL_XHCI)	+= intel-xhci-usb-role-
> switch.o
> +obj-$(CONFIG_TYPEB_CONN_GPIO)		+= typeb-conn-gpio.o
> diff --git a/drivers/usb/roles/typeb-conn-gpio.c b/drivers/usb/roles/typeb-
> conn-gpio.c
> new file mode 100644
> index 000000000000..097d2ca12a12
> --- /dev/null
> +++ b/drivers/usb/roles/typeb-conn-gpio.c
> @@ -0,0 +1,305 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * USB Type-B GPIO Connector Driver
> + *
> + * Copyright (C) 2019 MediaTek Inc.
> + *
> + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> + *
> + * Some code borrowed from drivers/extcon/extcon-usb-gpio.c  */
> +
> +#include <linux/device.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/interrupt.h>
> +#include <linux/irq.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_graph.h>
> +#include <linux/pinctrl/consumer.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/usb/role.h>
> +
> +#define USB_GPIO_DEB_MS		20	/* ms */
> +#define USB_GPIO_DEB_US		((USB_GPIO_DEB_MS) * 1000)	/* us
> */
> +
> +#define USB_CONN_IRQF	\
> +	(IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
> IRQF_ONESHOT)
> +
> +struct usb_conn_info {
> +	struct device *dev;
> +	struct usb_role_switch *role_sw;
> +	enum usb_role last_role;
> +	struct regulator *vbus;
> +	struct delayed_work dw_det;
> +	unsigned long debounce_jiffies;
> +
> +	struct gpio_desc *id_gpiod;
> +	struct gpio_desc *vbus_gpiod;
> +	int id_irq;
> +	int vbus_irq;
> +};
> +
> +/**
> + * "DEVICE" = VBUS and "HOST" = !ID, so we have:
> + * Both "DEVICE" and "HOST" can't be set as active at the same time
> + * so if "HOST" is active (i.e. ID is 0)  we keep "DEVICE" inactive
> + * even if VBUS is on.
> + *
> + *  Role          |   ID  |  VBUS
> + * ------------------------------------
> + *  [1] DEVICE    |   H   |   H
> + *  [2] NONE      |   H   |   L
> + *  [3] HOST      |   L   |   H
> + *  [4] HOST      |   L   |   L
> + *
> + * In case we have only one of these signals:
> + * - VBUS only - we want to distinguish between [1] and [2], so ID is
> +always 1
> + * - ID only - we want to distinguish between [1] and [4], so VBUS = ID
> +*/ static void usb_conn_detect_cable(struct work_struct *work) {
> +	struct usb_conn_info *info;
> +	enum usb_role role;
> +	int id, vbus, ret;
> +
> +	info = container_of(to_delayed_work(work),
> +			    struct usb_conn_info, dw_det);
> +
> +	/* check ID and VBUS */
> +	id = info->id_gpiod ?
> +		gpiod_get_value_cansleep(info->id_gpiod) : 1;
> +	vbus = info->vbus_gpiod ?
> +		gpiod_get_value_cansleep(info->vbus_gpiod) : id;
> +
> +	if (!id)
> +		role = USB_ROLE_HOST;
> +	else if (vbus)
> +		role = USB_ROLE_DEVICE;
> +	else
> +		role = USB_ROLE_NONE;
> +
> +	dev_dbg(info->dev, "role %d/%d, gpios: id %d, vbus %d\n",
> +		info->last_role, role, id, vbus);
> +
> +	if (info->last_role == role) {
> +		dev_warn(info->dev, "repeated role: %d\n", role);
> +		return;
> +	}
> +
> +	if (info->last_role == USB_ROLE_HOST)
> +		regulator_disable(info->vbus);
> +
> +	ret = usb_role_switch_set_role(info->role_sw, role);
> +	if (ret)
> +		dev_err(info->dev, "failed to set role: %d\n", ret);
> +
> +	if (role == USB_ROLE_HOST) {
> +		ret = regulator_enable(info->vbus);
> +		if (ret)
> +			dev_err(info->dev, "enable vbus regulator failed\n");
> +	}
> +
> +	info->last_role = role;
> +
> +	dev_dbg(info->dev, "vbus regulator is %s\n",
> +		regulator_is_enabled(info->vbus) ? "enabled" : "disabled"); }
> +
> +static void usb_conn_queue_dwork(struct usb_conn_info *info,
> +				 unsigned long delay)
> +{
> +	queue_delayed_work(system_power_efficient_wq, &info-
> >dw_det, delay); }
> +
> +static irqreturn_t usb_conn_isr(int irq, void *dev_id) {
> +	struct usb_conn_info *info = dev_id;
> +
> +	usb_conn_queue_dwork(info, info->debounce_jiffies);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int usb_conn_probe(struct platform_device *pdev) {
> +	struct device *dev = &pdev->dev;
> +	struct device_node *np = dev->of_node;
> +	struct device_node *parent;
> +	struct device_node *child;
> +	struct usb_conn_info *info;
> +	int ret = 0;
> +
> +	if (!np)
> +		return -EINVAL;
> +
> +	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
> +	if (!info)
> +		return -ENOMEM;
> +
> +	info->dev = dev;
> +
> +	child = of_get_child_by_name(np, "connector");
> +	if (!child) {
> +		dev_err(dev, "failed to find connector node\n");
> +		return -ENODEV;
> +	}
> +
> +	info->id_gpiod = devm_gpiod_get_from_of_node(
> +				dev, child, "id-gpios", 0, GPIOD_IN, "idpin");
> +	if (IS_ERR(info->id_gpiod)) {
> +		of_node_put(child);
> +		return PTR_ERR(info->id_gpiod);
> +	}
> +
> +	info->vbus_gpiod = devm_gpiod_get_from_of_node(
> +				dev, child, "vbus-gpios", 0, GPIOD_IN,
> +				"vbuspin");
> +	if (IS_ERR(info->vbus_gpiod)) {
> +		of_node_put(child);
> +		return PTR_ERR(info->vbus_gpiod);
> +	}
> +
> +	if (!info->id_gpiod && !info->vbus_gpiod) {
> +		dev_err(dev, "failed to get gpios\n");
> +		return -ENODEV;
> +	}
> +
> +	of_node_put(child);
> +
> +	if (info->id_gpiod)
> +		ret = gpiod_set_debounce(info->id_gpiod,
> USB_GPIO_DEB_US);
> +	if (!ret && info->vbus_gpiod)
> +		ret = gpiod_set_debounce(info->vbus_gpiod,
> USB_GPIO_DEB_US);
> +	if (ret < 0)
> +		info->debounce_jiffies =
> msecs_to_jiffies(USB_GPIO_DEB_MS);
> +
> +	INIT_DELAYED_WORK(&info->dw_det, usb_conn_detect_cable);
> +
> +	info->vbus = devm_regulator_get(dev, "vbus");
> +	if (IS_ERR(info->vbus)) {
> +		dev_err(dev, "failed to get vbus\n");
> +		return PTR_ERR(info->vbus);
> +	}
> +
> +	child = of_graph_get_endpoint_by_regs(np, -1, 0);
> +	parent = of_graph_get_remote_port_parent(child);
> +	info->role_sw =
> fwnode_usb_role_switch_get(of_fwnode_handle(parent));
> +	of_node_put(child);
> +	of_node_put(parent);
> +	if (IS_ERR(info->role_sw)) {
> +		dev_err(dev, "failed to get role switch\n");
> +		return PTR_ERR(info->role_sw);
> +	}
> +
> +	if (info->id_gpiod) {
> +		info->id_irq = gpiod_to_irq(info->id_gpiod);
> +		if (info->id_irq < 0) {
> +			dev_err(dev, "failed to get ID IRQ\n");
May be usb_role_switch_put(info->role_sw); ??
> +			return info->id_irq;
> +		}
> +
> +		ret = devm_request_threaded_irq(dev, info->id_irq, NULL,
> +						usb_conn_isr,
> USB_CONN_IRQF,
> +						pdev->name, info);
> +		if (ret < 0) {
> +			dev_err(dev, "failed to request ID IRQ\n");
May be usb_role_switch_put(info->role_sw); ??
> +			return ret;
> +		}
> +	}
> +
> +	if (info->vbus_gpiod) {
> +		info->vbus_irq = gpiod_to_irq(info->vbus_gpiod);
> +		if (info->vbus_irq < 0) {
> +			dev_err(dev, "failed to get VBUS IRQ\n");
May be usb_role_switch_put(info->role_sw);
> +			return info->vbus_irq;
> +		}
> +
> +		ret = devm_request_threaded_irq(dev, info->vbus_irq,
> NULL,
> +						usb_conn_isr,
> USB_CONN_IRQF,
> +						pdev->name, info);
> +		if (ret < 0) {
> +			dev_err(dev, "failed to request VBUS IRQ\n");
May be usb_role_switch_put(info->role_sw); ??
> +			return ret;
> +		}
> +	}
> +
> +	platform_set_drvdata(pdev, info);
> +
> +	/* Perform initial detection */
> +	usb_conn_queue_dwork(info, 0);
> +
> +	return 0;
> +}
> +
> +static int usb_conn_remove(struct platform_device *pdev) {
> +	struct usb_conn_info *info = platform_get_drvdata(pdev);
> +
> +	cancel_delayed_work_sync(&info->dw_det);
> +
> +	if (info->last_role == USB_ROLE_HOST)
> +		regulator_disable(info->vbus);
> +
> +	usb_role_switch_put(info->role_sw);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused usb_conn_suspend(struct device *dev) {
> +	struct usb_conn_info *info = dev_get_drvdata(dev);
> +
> +	if (info->id_gpiod)
> +		disable_irq(info->id_irq);
> +	if (info->vbus_gpiod)
> +		disable_irq(info->vbus_irq);
> +
> +	pinctrl_pm_select_sleep_state(dev);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused usb_conn_resume(struct device *dev) {
> +	struct usb_conn_info *info = dev_get_drvdata(dev);
> +
> +	pinctrl_pm_select_default_state(dev);
> +
> +	if (info->id_gpiod)
> +		enable_irq(info->id_irq);
> +	if (info->vbus_gpiod)
> +		enable_irq(info->vbus_irq);
> +
> +	usb_conn_queue_dwork(info, 0);
> +
> +	return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(usb_conn_pm_ops,
> +			 usb_conn_suspend, usb_conn_resume);
> +
> +#define DEV_PMS_OPS (IS_ENABLED(CONFIG_PM_SLEEP) ?
> &usb_conn_pm_ops :
> +NULL)
> +
> +static const struct of_device_id usb_conn_dt_match[] = {
> +	{ .compatible = "linux,typeb-conn-gpio", },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, usb_conn_dt_match);
> +
> +static struct platform_driver usb_conn_driver = {
> +	.probe		= usb_conn_probe,
> +	.remove		= usb_conn_remove,
> +	.driver		= {
> +		.name	= "typeb-conn-gpio",
> +		.pm	= DEV_PMS_OPS,
> +		.of_match_table = usb_conn_dt_match,
> +	},
> +};
> +
> +module_platform_driver(usb_conn_driver);
> +
> +MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
> +MODULE_DESCRIPTION("USB Type-B GPIO connector driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.21.0
Chunfeng Yun (云春峰) April 28, 2019, 9:26 a.m. UTC | #2 
Hi Biju,
On Fri, 2019-04-26 at 09:22 +0000, Biju Das wrote:
> Hi Chunfeng Yun,
> 
> Thanks for the patch.
> 
> > Subject: [PATCH v4 5/6] usb: roles: add USB Type-B GPIO connector driver
> > 
> > Due to the requirement of usb-connector.txt binding, the old way using
> > extcon to support USB Dual-Role switch is now deprecated when use Type-B
> > connector.
> > This patch introduces a driver of Type-B connector which typically uses an
> > input GPIO to detect USB ID pin, and try to replace the function provided by
> > extcon-usb-gpio driver
> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > v4 changes:
> >   1. remove linux/gpio.h suggested by Linus
> >   2. put node when error happens
> > 
> > v3 changes:
> >   1. treat bype-B connector as a virtual device;
> >   2. change file name again
> > 
> > v2 changes:
> >   1. file name is changed
> >   2. use new compatible
> > ---
> >  drivers/usb/roles/Kconfig           |  11 +
> >  drivers/usb/roles/Makefile          |   1 +
> >  drivers/usb/roles/typeb-conn-gpio.c | 305
> > ++++++++++++++++++++++++++++
> >  3 files changed, 317 insertions(+)
> >  create mode 100644 drivers/usb/roles/typeb-conn-gpio.c
> > 
> > diff --git a/drivers/usb/roles/Kconfig b/drivers/usb/roles/Kconfig index
> > f8b31aa67526..d1156e18a81a 100644
> > --- a/drivers/usb/roles/Kconfig
> > +++ b/drivers/usb/roles/Kconfig
> > @@ -26,4 +26,15 @@ config USB_ROLES_INTEL_XHCI
> >  	  To compile the driver as a module, choose M here: the module will
> >  	  be called intel-xhci-usb-role-switch.
> > 
> > +config TYPEB_CONN_GPIO
> > +	tristate "USB Type-B GPIO Connector"
> > +	depends on GPIOLIB
> > +	help
> > +	  The driver supports USB role switch between host and device via
> > GPIO
> > +	  based USB cable detection, used typically if an input GPIO is used
> > +	  to detect USB ID pin.
> > +
> > +	  To compile the driver as a module, choose M here: the module will
> > +	  be called typeb-conn-gpio.ko
> > +
> >  endif # USB_ROLE_SWITCH
> > diff --git a/drivers/usb/roles/Makefile b/drivers/usb/roles/Makefile index
> > 757a7d2797eb..5d5620d9d113 100644
> > --- a/drivers/usb/roles/Makefile
> > +++ b/drivers/usb/roles/Makefile
> > @@ -3,3 +3,4 @@
> >  obj-$(CONFIG_USB_ROLE_SWITCH)		+= roles.o
> >  roles-y					:= class.o
> >  obj-$(CONFIG_USB_ROLES_INTEL_XHCI)	+= intel-xhci-usb-role-
> > switch.o
> > +obj-$(CONFIG_TYPEB_CONN_GPIO)		+= typeb-conn-gpio.o
> > diff --git a/drivers/usb/roles/typeb-conn-gpio.c b/drivers/usb/roles/typeb-
> > conn-gpio.c
> > new file mode 100644
> > index 000000000000..097d2ca12a12
> > --- /dev/null
> > +++ b/drivers/usb/roles/typeb-conn-gpio.c
> > @@ -0,0 +1,305 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * USB Type-B GPIO Connector Driver
> > + *
> > + * Copyright (C) 2019 MediaTek Inc.
> > + *
> > + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > + *
> > + * Some code borrowed from drivers/extcon/extcon-usb-gpio.c  */
> > +
> > +#include <linux/device.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/irq.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_graph.h>
> > +#include <linux/pinctrl/consumer.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <linux/usb/role.h>
> > +
> > +#define USB_GPIO_DEB_MS		20	/* ms */
> > +#define USB_GPIO_DEB_US		((USB_GPIO_DEB_MS) * 1000)	/* us
> > */
> > +
> > +#define USB_CONN_IRQF	\
> > +	(IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
> > IRQF_ONESHOT)
> > +
> > +struct usb_conn_info {
> > +	struct device *dev;
> > +	struct usb_role_switch *role_sw;
> > +	enum usb_role last_role;
> > +	struct regulator *vbus;
> > +	struct delayed_work dw_det;
> > +	unsigned long debounce_jiffies;
> > +
> > +	struct gpio_desc *id_gpiod;
> > +	struct gpio_desc *vbus_gpiod;
> > +	int id_irq;
> > +	int vbus_irq;
> > +};
> > +
> > +/**
> > + * "DEVICE" = VBUS and "HOST" = !ID, so we have:
> > + * Both "DEVICE" and "HOST" can't be set as active at the same time
> > + * so if "HOST" is active (i.e. ID is 0)  we keep "DEVICE" inactive
> > + * even if VBUS is on.
> > + *
> > + *  Role          |   ID  |  VBUS
> > + * ------------------------------------
> > + *  [1] DEVICE    |   H   |   H
> > + *  [2] NONE      |   H   |   L
> > + *  [3] HOST      |   L   |   H
> > + *  [4] HOST      |   L   |   L
> > + *
> > + * In case we have only one of these signals:
> > + * - VBUS only - we want to distinguish between [1] and [2], so ID is
> > +always 1
> > + * - ID only - we want to distinguish between [1] and [4], so VBUS = ID
> > +*/ static void usb_conn_detect_cable(struct work_struct *work) {
> > +	struct usb_conn_info *info;
> > +	enum usb_role role;
> > +	int id, vbus, ret;
> > +
> > +	info = container_of(to_delayed_work(work),
> > +			    struct usb_conn_info, dw_det);
> > +
> > +	/* check ID and VBUS */
> > +	id = info->id_gpiod ?
> > +		gpiod_get_value_cansleep(info->id_gpiod) : 1;
> > +	vbus = info->vbus_gpiod ?
> > +		gpiod_get_value_cansleep(info->vbus_gpiod) : id;
> > +
> > +	if (!id)
> > +		role = USB_ROLE_HOST;
> > +	else if (vbus)
> > +		role = USB_ROLE_DEVICE;
> > +	else
> > +		role = USB_ROLE_NONE;
> > +
> > +	dev_dbg(info->dev, "role %d/%d, gpios: id %d, vbus %d\n",
> > +		info->last_role, role, id, vbus);
> > +
> > +	if (info->last_role == role) {
> > +		dev_warn(info->dev, "repeated role: %d\n", role);
> > +		return;
> > +	}
> > +
> > +	if (info->last_role == USB_ROLE_HOST)
> > +		regulator_disable(info->vbus);
> > +
> > +	ret = usb_role_switch_set_role(info->role_sw, role);
> > +	if (ret)
> > +		dev_err(info->dev, "failed to set role: %d\n", ret);
> > +
> > +	if (role == USB_ROLE_HOST) {
> > +		ret = regulator_enable(info->vbus);
> > +		if (ret)
> > +			dev_err(info->dev, "enable vbus regulator failed\n");
> > +	}
> > +
> > +	info->last_role = role;
> > +
> > +	dev_dbg(info->dev, "vbus regulator is %s\n",
> > +		regulator_is_enabled(info->vbus) ? "enabled" : "disabled"); }
> > +
> > +static void usb_conn_queue_dwork(struct usb_conn_info *info,
> > +				 unsigned long delay)
> > +{
> > +	queue_delayed_work(system_power_efficient_wq, &info-
> > >dw_det, delay); }
> > +
> > +static irqreturn_t usb_conn_isr(int irq, void *dev_id) {
> > +	struct usb_conn_info *info = dev_id;
> > +
> > +	usb_conn_queue_dwork(info, info->debounce_jiffies);
> > +
> > +	return IRQ_HANDLED;
> > +}
> > +
> > +static int usb_conn_probe(struct platform_device *pdev) {
> > +	struct device *dev = &pdev->dev;
> > +	struct device_node *np = dev->of_node;
> > +	struct device_node *parent;
> > +	struct device_node *child;
> > +	struct usb_conn_info *info;
> > +	int ret = 0;
> > +
> > +	if (!np)
> > +		return -EINVAL;
> > +
> > +	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
> > +	if (!info)
> > +		return -ENOMEM;
> > +
> > +	info->dev = dev;
> > +
> > +	child = of_get_child_by_name(np, "connector");
> > +	if (!child) {
> > +		dev_err(dev, "failed to find connector node\n");
> > +		return -ENODEV;
> > +	}
> > +
> > +	info->id_gpiod = devm_gpiod_get_from_of_node(
> > +				dev, child, "id-gpios", 0, GPIOD_IN, "idpin");
> > +	if (IS_ERR(info->id_gpiod)) {
> > +		of_node_put(child);
> > +		return PTR_ERR(info->id_gpiod);
> > +	}
> > +
> > +	info->vbus_gpiod = devm_gpiod_get_from_of_node(
> > +				dev, child, "vbus-gpios", 0, GPIOD_IN,
> > +				"vbuspin");
> > +	if (IS_ERR(info->vbus_gpiod)) {
> > +		of_node_put(child);
> > +		return PTR_ERR(info->vbus_gpiod);
> > +	}
> > +
> > +	if (!info->id_gpiod && !info->vbus_gpiod) {
> > +		dev_err(dev, "failed to get gpios\n");
> > +		return -ENODEV;
> > +	}
> > +
> > +	of_node_put(child);
> > +
> > +	if (info->id_gpiod)
> > +		ret = gpiod_set_debounce(info->id_gpiod,
> > USB_GPIO_DEB_US);
> > +	if (!ret && info->vbus_gpiod)
> > +		ret = gpiod_set_debounce(info->vbus_gpiod,
> > USB_GPIO_DEB_US);
> > +	if (ret < 0)
> > +		info->debounce_jiffies =
> > msecs_to_jiffies(USB_GPIO_DEB_MS);
> > +
> > +	INIT_DELAYED_WORK(&info->dw_det, usb_conn_detect_cable);
> > +
> > +	info->vbus = devm_regulator_get(dev, "vbus");
> > +	if (IS_ERR(info->vbus)) {
> > +		dev_err(dev, "failed to get vbus\n");
> > +		return PTR_ERR(info->vbus);
> > +	}
> > +
> > +	child = of_graph_get_endpoint_by_regs(np, -1, 0);
> > +	parent = of_graph_get_remote_port_parent(child);
> > +	info->role_sw =
> > fwnode_usb_role_switch_get(of_fwnode_handle(parent));
> > +	of_node_put(child);
> > +	of_node_put(parent);
> > +	if (IS_ERR(info->role_sw)) {
> > +		dev_err(dev, "failed to get role switch\n");
> > +		return PTR_ERR(info->role_sw);
> > +	}
> > +
> > +	if (info->id_gpiod) {
> > +		info->id_irq = gpiod_to_irq(info->id_gpiod);
> > +		if (info->id_irq < 0) {
> > +			dev_err(dev, "failed to get ID IRQ\n");
> May be usb_role_switch_put(info->role_sw); ??
Good catch, will fix it.

Thanks
> > +			return info->id_irq;
> > +		}
> > +
> > +		ret = devm_request_threaded_irq(dev, info->id_irq, NULL,
> > +						usb_conn_isr,
> > USB_CONN_IRQF,
> > +						pdev->name, info);
> > +		if (ret < 0) {
> > +			dev_err(dev, "failed to request ID IRQ\n");
> May be usb_role_switch_put(info->role_sw); ??
> > +			return ret;
> > +		}
> > +	}
> > +
> > +	if (info->vbus_gpiod) {
> > +		info->vbus_irq = gpiod_to_irq(info->vbus_gpiod);
> > +		if (info->vbus_irq < 0) {
> > +			dev_err(dev, "failed to get VBUS IRQ\n");
> May be usb_role_switch_put(info->role_sw);
> > +			return info->vbus_irq;
> > +		}
> > +
> > +		ret = devm_request_threaded_irq(dev, info->vbus_irq,
> > NULL,
> > +						usb_conn_isr,
> > USB_CONN_IRQF,
> > +						pdev->name, info);
> > +		if (ret < 0) {
> > +			dev_err(dev, "failed to request VBUS IRQ\n");
> May be usb_role_switch_put(info->role_sw); ??
> > +			return ret;
> > +		}
> > +	}
> > +
> > +	platform_set_drvdata(pdev, info);
> > +
> > +	/* Perform initial detection */
> > +	usb_conn_queue_dwork(info, 0);
> > +
> > +	return 0;
> > +}
> > +
> > +static int usb_conn_remove(struct platform_device *pdev) {
> > +	struct usb_conn_info *info = platform_get_drvdata(pdev);
> > +
> > +	cancel_delayed_work_sync(&info->dw_det);
> > +
> > +	if (info->last_role == USB_ROLE_HOST)
> > +		regulator_disable(info->vbus);
> > +
> > +	usb_role_switch_put(info->role_sw);
> > +
> > +	return 0;
> > +}
> > +
> > +static int __maybe_unused usb_conn_suspend(struct device *dev) {
> > +	struct usb_conn_info *info = dev_get_drvdata(dev);
> > +
> > +	if (info->id_gpiod)
> > +		disable_irq(info->id_irq);
> > +	if (info->vbus_gpiod)
> > +		disable_irq(info->vbus_irq);
> > +
> > +	pinctrl_pm_select_sleep_state(dev);
> > +
> > +	return 0;
> > +}
> > +
> > +static int __maybe_unused usb_conn_resume(struct device *dev) {
> > +	struct usb_conn_info *info = dev_get_drvdata(dev);
> > +
> > +	pinctrl_pm_select_default_state(dev);
> > +
> > +	if (info->id_gpiod)
> > +		enable_irq(info->id_irq);
> > +	if (info->vbus_gpiod)
> > +		enable_irq(info->vbus_irq);
> > +
> > +	usb_conn_queue_dwork(info, 0);
> > +
> > +	return 0;
> > +}
> > +
> > +static SIMPLE_DEV_PM_OPS(usb_conn_pm_ops,
> > +			 usb_conn_suspend, usb_conn_resume);
> > +
> > +#define DEV_PMS_OPS (IS_ENABLED(CONFIG_PM_SLEEP) ?
> > &usb_conn_pm_ops :
> > +NULL)
> > +
> > +static const struct of_device_id usb_conn_dt_match[] = {
> > +	{ .compatible = "linux,typeb-conn-gpio", },
> > +	{ }
> > +};
> > +MODULE_DEVICE_TABLE(of, usb_conn_dt_match);
> > +
> > +static struct platform_driver usb_conn_driver = {
> > +	.probe		= usb_conn_probe,
> > +	.remove		= usb_conn_remove,
> > +	.driver		= {
> > +		.name	= "typeb-conn-gpio",
> > +		.pm	= DEV_PMS_OPS,
> > +		.of_match_table = usb_conn_dt_match,
> > +	},
> > +};
> > +
> > +module_platform_driver(usb_conn_driver);
> > +
> > +MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
> > +MODULE_DESCRIPTION("USB Type-B GPIO connector driver");
> > +MODULE_LICENSE("GPL v2");
> > --
> > 2.21.0
>
diff mbox series

Patch

diff --git a/drivers/usb/roles/Kconfig b/drivers/usb/roles/Kconfig
index f8b31aa67526..d1156e18a81a 100644
--- a/drivers/usb/roles/Kconfig
+++ b/drivers/usb/roles/Kconfig
@@ -26,4 +26,15 @@  config USB_ROLES_INTEL_XHCI
 	  To compile the driver as a module, choose M here: the module will
 	  be called intel-xhci-usb-role-switch.
 
+config TYPEB_CONN_GPIO
+	tristate "USB Type-B GPIO Connector"
+	depends on GPIOLIB
+	help
+	  The driver supports USB role switch between host and device via GPIO
+	  based USB cable detection, used typically if an input GPIO is used
+	  to detect USB ID pin.
+
+	  To compile the driver as a module, choose M here: the module will
+	  be called typeb-conn-gpio.ko
+
 endif # USB_ROLE_SWITCH
diff --git a/drivers/usb/roles/Makefile b/drivers/usb/roles/Makefile
index 757a7d2797eb..5d5620d9d113 100644
--- a/drivers/usb/roles/Makefile
+++ b/drivers/usb/roles/Makefile
@@ -3,3 +3,4 @@ 
 obj-$(CONFIG_USB_ROLE_SWITCH)		+= roles.o
 roles-y					:= class.o
 obj-$(CONFIG_USB_ROLES_INTEL_XHCI)	+= intel-xhci-usb-role-switch.o
+obj-$(CONFIG_TYPEB_CONN_GPIO)		+= typeb-conn-gpio.o
diff --git a/drivers/usb/roles/typeb-conn-gpio.c b/drivers/usb/roles/typeb-conn-gpio.c
new file mode 100644
index 000000000000..097d2ca12a12
--- /dev/null
+++ b/drivers/usb/roles/typeb-conn-gpio.c
@@ -0,0 +1,305 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * USB Type-B GPIO Connector Driver
+ *
+ * Copyright (C) 2019 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ *
+ * Some code borrowed from drivers/extcon/extcon-usb-gpio.c
+ */
+
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/usb/role.h>
+
+#define USB_GPIO_DEB_MS		20	/* ms */
+#define USB_GPIO_DEB_US		((USB_GPIO_DEB_MS) * 1000)	/* us */
+
+#define USB_CONN_IRQF	\
+	(IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | IRQF_ONESHOT)
+
+struct usb_conn_info {
+	struct device *dev;
+	struct usb_role_switch *role_sw;
+	enum usb_role last_role;
+	struct regulator *vbus;
+	struct delayed_work dw_det;
+	unsigned long debounce_jiffies;
+
+	struct gpio_desc *id_gpiod;
+	struct gpio_desc *vbus_gpiod;
+	int id_irq;
+	int vbus_irq;
+};
+
+/**
+ * "DEVICE" = VBUS and "HOST" = !ID, so we have:
+ * Both "DEVICE" and "HOST" can't be set as active at the same time
+ * so if "HOST" is active (i.e. ID is 0)  we keep "DEVICE" inactive
+ * even if VBUS is on.
+ *
+ *  Role          |   ID  |  VBUS
+ * ------------------------------------
+ *  [1] DEVICE    |   H   |   H
+ *  [2] NONE      |   H   |   L
+ *  [3] HOST      |   L   |   H
+ *  [4] HOST      |   L   |   L
+ *
+ * In case we have only one of these signals:
+ * - VBUS only - we want to distinguish between [1] and [2], so ID is always 1
+ * - ID only - we want to distinguish between [1] and [4], so VBUS = ID
+ */
+static void usb_conn_detect_cable(struct work_struct *work)
+{
+	struct usb_conn_info *info;
+	enum usb_role role;
+	int id, vbus, ret;
+
+	info = container_of(to_delayed_work(work),
+			    struct usb_conn_info, dw_det);
+
+	/* check ID and VBUS */
+	id = info->id_gpiod ?
+		gpiod_get_value_cansleep(info->id_gpiod) : 1;
+	vbus = info->vbus_gpiod ?
+		gpiod_get_value_cansleep(info->vbus_gpiod) : id;
+
+	if (!id)
+		role = USB_ROLE_HOST;
+	else if (vbus)
+		role = USB_ROLE_DEVICE;
+	else
+		role = USB_ROLE_NONE;
+
+	dev_dbg(info->dev, "role %d/%d, gpios: id %d, vbus %d\n",
+		info->last_role, role, id, vbus);
+
+	if (info->last_role == role) {
+		dev_warn(info->dev, "repeated role: %d\n", role);
+		return;
+	}
+
+	if (info->last_role == USB_ROLE_HOST)
+		regulator_disable(info->vbus);
+
+	ret = usb_role_switch_set_role(info->role_sw, role);
+	if (ret)
+		dev_err(info->dev, "failed to set role: %d\n", ret);
+
+	if (role == USB_ROLE_HOST) {
+		ret = regulator_enable(info->vbus);
+		if (ret)
+			dev_err(info->dev, "enable vbus regulator failed\n");
+	}
+
+	info->last_role = role;
+
+	dev_dbg(info->dev, "vbus regulator is %s\n",
+		regulator_is_enabled(info->vbus) ? "enabled" : "disabled");
+}
+
+static void usb_conn_queue_dwork(struct usb_conn_info *info,
+				 unsigned long delay)
+{
+	queue_delayed_work(system_power_efficient_wq, &info->dw_det, delay);
+}
+
+static irqreturn_t usb_conn_isr(int irq, void *dev_id)
+{
+	struct usb_conn_info *info = dev_id;
+
+	usb_conn_queue_dwork(info, info->debounce_jiffies);
+
+	return IRQ_HANDLED;
+}
+
+static int usb_conn_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *parent;
+	struct device_node *child;
+	struct usb_conn_info *info;
+	int ret = 0;
+
+	if (!np)
+		return -EINVAL;
+
+	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	info->dev = dev;
+
+	child = of_get_child_by_name(np, "connector");
+	if (!child) {
+		dev_err(dev, "failed to find connector node\n");
+		return -ENODEV;
+	}
+
+	info->id_gpiod = devm_gpiod_get_from_of_node(
+				dev, child, "id-gpios", 0, GPIOD_IN, "idpin");
+	if (IS_ERR(info->id_gpiod)) {
+		of_node_put(child);
+		return PTR_ERR(info->id_gpiod);
+	}
+
+	info->vbus_gpiod = devm_gpiod_get_from_of_node(
+				dev, child, "vbus-gpios", 0, GPIOD_IN,
+				"vbuspin");
+	if (IS_ERR(info->vbus_gpiod)) {
+		of_node_put(child);
+		return PTR_ERR(info->vbus_gpiod);
+	}
+
+	if (!info->id_gpiod && !info->vbus_gpiod) {
+		dev_err(dev, "failed to get gpios\n");
+		return -ENODEV;
+	}
+
+	of_node_put(child);
+
+	if (info->id_gpiod)
+		ret = gpiod_set_debounce(info->id_gpiod, USB_GPIO_DEB_US);
+	if (!ret && info->vbus_gpiod)
+		ret = gpiod_set_debounce(info->vbus_gpiod, USB_GPIO_DEB_US);
+	if (ret < 0)
+		info->debounce_jiffies = msecs_to_jiffies(USB_GPIO_DEB_MS);
+
+	INIT_DELAYED_WORK(&info->dw_det, usb_conn_detect_cable);
+
+	info->vbus = devm_regulator_get(dev, "vbus");
+	if (IS_ERR(info->vbus)) {
+		dev_err(dev, "failed to get vbus\n");
+		return PTR_ERR(info->vbus);
+	}
+
+	child = of_graph_get_endpoint_by_regs(np, -1, 0);
+	parent = of_graph_get_remote_port_parent(child);
+	info->role_sw = fwnode_usb_role_switch_get(of_fwnode_handle(parent));
+	of_node_put(child);
+	of_node_put(parent);
+	if (IS_ERR(info->role_sw)) {
+		dev_err(dev, "failed to get role switch\n");
+		return PTR_ERR(info->role_sw);
+	}
+
+	if (info->id_gpiod) {
+		info->id_irq = gpiod_to_irq(info->id_gpiod);
+		if (info->id_irq < 0) {
+			dev_err(dev, "failed to get ID IRQ\n");
+			return info->id_irq;
+		}
+
+		ret = devm_request_threaded_irq(dev, info->id_irq, NULL,
+						usb_conn_isr, USB_CONN_IRQF,
+						pdev->name, info);
+		if (ret < 0) {
+			dev_err(dev, "failed to request ID IRQ\n");
+			return ret;
+		}
+	}
+
+	if (info->vbus_gpiod) {
+		info->vbus_irq = gpiod_to_irq(info->vbus_gpiod);
+		if (info->vbus_irq < 0) {
+			dev_err(dev, "failed to get VBUS IRQ\n");
+			return info->vbus_irq;
+		}
+
+		ret = devm_request_threaded_irq(dev, info->vbus_irq, NULL,
+						usb_conn_isr, USB_CONN_IRQF,
+						pdev->name, info);
+		if (ret < 0) {
+			dev_err(dev, "failed to request VBUS IRQ\n");
+			return ret;
+		}
+	}
+
+	platform_set_drvdata(pdev, info);
+
+	/* Perform initial detection */
+	usb_conn_queue_dwork(info, 0);
+
+	return 0;
+}
+
+static int usb_conn_remove(struct platform_device *pdev)
+{
+	struct usb_conn_info *info = platform_get_drvdata(pdev);
+
+	cancel_delayed_work_sync(&info->dw_det);
+
+	if (info->last_role == USB_ROLE_HOST)
+		regulator_disable(info->vbus);
+
+	usb_role_switch_put(info->role_sw);
+
+	return 0;
+}
+
+static int __maybe_unused usb_conn_suspend(struct device *dev)
+{
+	struct usb_conn_info *info = dev_get_drvdata(dev);
+
+	if (info->id_gpiod)
+		disable_irq(info->id_irq);
+	if (info->vbus_gpiod)
+		disable_irq(info->vbus_irq);
+
+	pinctrl_pm_select_sleep_state(dev);
+
+	return 0;
+}
+
+static int __maybe_unused usb_conn_resume(struct device *dev)
+{
+	struct usb_conn_info *info = dev_get_drvdata(dev);
+
+	pinctrl_pm_select_default_state(dev);
+
+	if (info->id_gpiod)
+		enable_irq(info->id_irq);
+	if (info->vbus_gpiod)
+		enable_irq(info->vbus_irq);
+
+	usb_conn_queue_dwork(info, 0);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(usb_conn_pm_ops,
+			 usb_conn_suspend, usb_conn_resume);
+
+#define DEV_PMS_OPS (IS_ENABLED(CONFIG_PM_SLEEP) ? &usb_conn_pm_ops : NULL)
+
+static const struct of_device_id usb_conn_dt_match[] = {
+	{ .compatible = "linux,typeb-conn-gpio", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, usb_conn_dt_match);
+
+static struct platform_driver usb_conn_driver = {
+	.probe		= usb_conn_probe,
+	.remove		= usb_conn_remove,
+	.driver		= {
+		.name	= "typeb-conn-gpio",
+		.pm	= DEV_PMS_OPS,
+		.of_match_table = usb_conn_dt_match,
+	},
+};
+
+module_platform_driver(usb_conn_driver);
+
+MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
+MODULE_DESCRIPTION("USB Type-B GPIO connector driver");
+MODULE_LICENSE("GPL v2");