diff mbox series

[v2,1/5] mtd: rawnand: mtk: Correct low level time calculation of r/w cycle

Message ID 20190430100250.28083-2-xiaolei.li@mediatek.com (mailing list archive)
State New, archived
Headers show
Series MTK NAND driver improvements and fixes | expand

Commit Message

xiaolei li April 30, 2019, 10:02 a.m. UTC 
At present, the flow of calculating AC timing of read/write cycle in SDR
mode is that:
At first, calculate high hold time which is valid for both read and write
cycle using the max value between tREH_min and tWH_min.
Secondly, calculate WE# pulse width using tWP_min.
Thridly, calculate RE# pulse width using the bigger one between tREA_max
and tRP_min.

But NAND SPEC shows that Controller should also meet write/read cycle time.
That is write cycle time should be more than tWC_min and read cycle should
be more than tRC_min. Obviously, we do not achieve that now.

This patch corrects the low level time calculation to meet minimum
read/write cycle time required. After getting the high hold time, WE# low
level time will be promised to meet tWP_min and tWC_min requirement,
and RE# low level time will be promised to meet tREA_max, tRP_min and
tRC_min requirement.

Fixes: edfee3619c49 ("mtd: nand: mtk: add ->setup_data_interface() hook")
Cc: stable@vger.kernel.org
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
---
 drivers/mtd/nand/raw/mtk_nand.c | 24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)

Comments

Miquel Raynal April 30, 2019, 11:59 a.m. UTC | #1 
Hi Xiaolei,

Xiaolei Li <xiaolei.li@mediatek.com> wrote on Tue, 30 Apr 2019 18:02:46
+0800:

> At present, the flow of calculating AC timing of read/write cycle in SDR
> mode is that:
> At first, calculate high hold time which is valid for both read and write
> cycle using the max value between tREH_min and tWH_min.
> Secondly, calculate WE# pulse width using tWP_min.
> Thridly, calculate RE# pulse width using the bigger one between tREA_max
> and tRP_min.
> 
> But NAND SPEC shows that Controller should also meet write/read cycle time.
> That is write cycle time should be more than tWC_min and read cycle should
> be more than tRC_min. Obviously, we do not achieve that now.
> 
> This patch corrects the low level time calculation to meet minimum
> read/write cycle time required. After getting the high hold time, WE# low
> level time will be promised to meet tWP_min and tWC_min requirement,
> and RE# low level time will be promised to meet tREA_max, tRP_min and
> tRC_min requirement.
> 
> Fixes: edfee3619c49 ("mtd: nand: mtk: add ->setup_data_interface() hook")
> Cc: stable@vger.kernel.org
> Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
> ---
>  drivers/mtd/nand/raw/mtk_nand.c | 24 +++++++++++++++++++++---
>  1 file changed, 21 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/mtd/nand/raw/mtk_nand.c b/drivers/mtd/nand/raw/mtk_nand.c
> index b6b4602f5132..4fbb0c6ecae3 100644
> --- a/drivers/mtd/nand/raw/mtk_nand.c
> +++ b/drivers/mtd/nand/raw/mtk_nand.c
> @@ -508,7 +508,8 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
>  {
>  	struct mtk_nfc *nfc = nand_get_controller_data(chip);
>  	const struct nand_sdr_timings *timings;
> -	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst, trlt;
> +	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0;
> +	u32 thold;
>  
>  	timings = nand_get_sdr_timings(conf);
>  	if (IS_ERR(timings))
> @@ -544,11 +545,28 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
>  	twh = DIV_ROUND_UP(twh * rate, 1000000) - 1;
>  	twh &= 0xf;
>  
> -	twst = timings->tWP_min / 1000;
> +	/* Calculate real WE#/RE# hold time in nanosecond */
> +	thold = (twh + 1) * 1000000 / rate;
> +	/* nanosecond to picosecond */
> +	thold *= 1000;
> +
> +	/**

        /*

> +	 * WE# low level time should be expaned to meet WE# pulse time
> +	 * and WE# cycle time at the same time.
> +	 */
> +	if (thold < timings->tWC_min)
> +		twst = timings->tWC_min - thold;
> +	twst = max(timings->tWP_min, twst) / 1000;
>  	twst = DIV_ROUND_UP(twst * rate, 1000000) - 1;
>  	twst &= 0xf;
>  
> -	trlt = max(timings->tREA_max, timings->tRP_min) / 1000;
> +	/**

Ditto

> +	 * RE# low level time should be expaned to meet RE# pulse time,
> +	 * RE# access time and RE# cycle time at the same time.
> +	 */
> +	if (thold < timings->tRC_min)
> +		trlt = timings->tRC_min - thold;
> +	trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000;
>  	trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1;
>  	trlt &= 0xf;
>  

With this fixed:

Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>


Thanks,
Miquèl
xiaolei li May 5, 2019, 7:12 a.m. UTC | #2 
On Tue, 2019-04-30 at 13:59 +0200, Miquel Raynal wrote:
> Hi Xiaolei,
> 
> Xiaolei Li <xiaolei.li@mediatek.com> wrote on Tue, 30 Apr 2019 18:02:46
> +0800:
> 
> > At present, the flow of calculating AC timing of read/write cycle in SDR
> > mode is that:
> > At first, calculate high hold time which is valid for both read and write
> > cycle using the max value between tREH_min and tWH_min.
> > Secondly, calculate WE# pulse width using tWP_min.
> > Thridly, calculate RE# pulse width using the bigger one between tREA_max
> > and tRP_min.
> > 
> > But NAND SPEC shows that Controller should also meet write/read cycle time.
> > That is write cycle time should be more than tWC_min and read cycle should
> > be more than tRC_min. Obviously, we do not achieve that now.
> > 
> > This patch corrects the low level time calculation to meet minimum
> > read/write cycle time required. After getting the high hold time, WE# low
> > level time will be promised to meet tWP_min and tWC_min requirement,
> > and RE# low level time will be promised to meet tREA_max, tRP_min and
> > tRC_min requirement.
> > 
> > Fixes: edfee3619c49 ("mtd: nand: mtk: add ->setup_data_interface() hook")
> > Cc: stable@vger.kernel.org
> > Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
> > ---
> >  drivers/mtd/nand/raw/mtk_nand.c | 24 +++++++++++++++++++++---
> >  1 file changed, 21 insertions(+), 3 deletions(-)
> > 
> > diff --git a/drivers/mtd/nand/raw/mtk_nand.c b/drivers/mtd/nand/raw/mtk_nand.c
> > index b6b4602f5132..4fbb0c6ecae3 100644
> > --- a/drivers/mtd/nand/raw/mtk_nand.c
> > +++ b/drivers/mtd/nand/raw/mtk_nand.c
> > @@ -508,7 +508,8 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
> >  {
> >  	struct mtk_nfc *nfc = nand_get_controller_data(chip);
> >  	const struct nand_sdr_timings *timings;
> > -	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst, trlt;
> > +	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0;
> > +	u32 thold;
> >  
> >  	timings = nand_get_sdr_timings(conf);
> >  	if (IS_ERR(timings))
> > @@ -544,11 +545,28 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
> >  	twh = DIV_ROUND_UP(twh * rate, 1000000) - 1;
> >  	twh &= 0xf;
> >  
> > -	twst = timings->tWP_min / 1000;
> > +	/* Calculate real WE#/RE# hold time in nanosecond */
> > +	thold = (twh + 1) * 1000000 / rate;
> > +	/* nanosecond to picosecond */
> > +	thold *= 1000;
> > +
> > +	/**
> 
>         /*
> 
> > +	 * WE# low level time should be expaned to meet WE# pulse time
> > +	 * and WE# cycle time at the same time.
> > +	 */
> > +	if (thold < timings->tWC_min)
> > +		twst = timings->tWC_min - thold;
> > +	twst = max(timings->tWP_min, twst) / 1000;
> >  	twst = DIV_ROUND_UP(twst * rate, 1000000) - 1;
> >  	twst &= 0xf;
> >  
> > -	trlt = max(timings->tREA_max, timings->tRP_min) / 1000;
> > +	/**
> 
> Ditto
OK.

> 
> > +	 * RE# low level time should be expaned to meet RE# pulse time,
> > +	 * RE# access time and RE# cycle time at the same time.
> > +	 */
> > +	if (thold < timings->tRC_min)
> > +		trlt = timings->tRC_min - thold;
> > +	trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000;
> >  	trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1;
> >  	trlt &= 0xf;
> >  
> 
> With this fixed:
> 
> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
> 
> 
> Thanks,
> Miquèl

Thanks,
Xiaolei
diff mbox series

Patch

diff --git a/drivers/mtd/nand/raw/mtk_nand.c b/drivers/mtd/nand/raw/mtk_nand.c
index b6b4602f5132..4fbb0c6ecae3 100644
--- a/drivers/mtd/nand/raw/mtk_nand.c
+++ b/drivers/mtd/nand/raw/mtk_nand.c
@@ -508,7 +508,8 @@  static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 {
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *timings;
-	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst, trlt;
+	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0;
+	u32 thold;
 
 	timings = nand_get_sdr_timings(conf);
 	if (IS_ERR(timings))
@@ -544,11 +545,28 @@  static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 	twh = DIV_ROUND_UP(twh * rate, 1000000) - 1;
 	twh &= 0xf;
 
-	twst = timings->tWP_min / 1000;
+	/* Calculate real WE#/RE# hold time in nanosecond */
+	thold = (twh + 1) * 1000000 / rate;
+	/* nanosecond to picosecond */
+	thold *= 1000;
+
+	/**
+	 * WE# low level time should be expaned to meet WE# pulse time
+	 * and WE# cycle time at the same time.
+	 */
+	if (thold < timings->tWC_min)
+		twst = timings->tWC_min - thold;
+	twst = max(timings->tWP_min, twst) / 1000;
 	twst = DIV_ROUND_UP(twst * rate, 1000000) - 1;
 	twst &= 0xf;
 
-	trlt = max(timings->tREA_max, timings->tRP_min) / 1000;
+	/**
+	 * RE# low level time should be expaned to meet RE# pulse time,
+	 * RE# access time and RE# cycle time at the same time.
+	 */
+	if (thold < timings->tRC_min)
+		trlt = timings->tRC_min - thold;
+	trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000;
 	trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1;
 	trlt &= 0xf;