| Message ID | 20190509020352.14282-1-masneyb@onstation.org (mailing list archive) |
|---|---|
| Headers | show |
| Series | ARM: qcom: initial Nexus 5 display support | expand |
On Wed, May 08, 2019 at 10:03:46PM -0400, Brian Masney wrote: > Here is a patch series that adds initial display support for the LG > Nexus 5 (hammerhead) phone. It's not fully working so that's why some > of these patches are RFC until we can get it fully working. > > The phones boots into terminal mode, however there is a several second > (or more) delay when writing to tty1 compared to when the changes are > actually shown on the screen. The following errors are in dmesg: I attached the full dmesg output with this patch series applied. I enabled debugging messages for just the DRM subsystem. Brian [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty (masneyb@ins7386) (gcc version 8.1.1 20180626 (Red Hat Cross 8.1.1-3) (GCC)) #303 SMP PREEMPT Wed May 8 21:59:17 EDT 2019 [ 0.000000] CPU: ARMv7 Processor [512f06f0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: LGE MSM 8974 HAMMERHEAD [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 256 MiB at 0x20000000 [ 0.000000] On node 0 totalpages: 491776 [ 0.000000] Normal zone: 1536 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 164096 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327680 pages, LIFO batch:63 [ 0.000000] percpu: Embedded 17 pages/cpu s39756 r8192 d21684 u69632 [ 0.000000] pcpu-alloc: s39756 r8192 d21684 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 490240 [ 0.000000] Kernel command line: console=tty0 console=ttyMSM0,115200,n8 rootwait androidboot.hardware=hammerhead user_debug=31 maxcpus=2 msm_watchdog_v2.enable=1 PMOS_NO_OUTPUT_REDIRECT=1 uart_console=enable gpt=enable lge.kcal=0|0|0|x lge.rev=rev_11 androidboot.laf androidboot.emmc=true fastboot=true androidboot.serialno=019eef1708e40fd2 androidboot.bootloader=HHZ20h androidboot.baseband=msm androidboot.hardware.sku=D820 androidboot.hardware.ddr=hynix androidboot.hardware.display=orise androidboot.revision=11 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1633208K/1967104K available (8192K kernel code, 834K rwdata, 3436K rodata, 1024K init, 266K bss, 71752K reserved, 262144K cma-reserved, 1310720K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x300/0x490 with crng_init=0 [ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.000017] Switching to timer-based delay loop, resolution 52ns [ 0.000410] Console: colour dummy device 80x30 [ 0.000785] printk: console [tty0] enabled [ 0.000823] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) [ 0.000854] pid_max: default: 32768 minimum: 301 [ 0.000984] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001014] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001504] *** VALIDATE proc *** [ 0.001629] *** VALIDATE cgroup1 *** [ 0.001651] *** VALIDATE cgroup2 *** [ 0.001676] CPU: Testing write buffer coherency: ok [ 0.001939] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.059943] Setting up static identity map for 0x300000 - 0x300060 [ 0.079942] rcu: Hierarchical SRCU implementation. [ 0.120017] smp: Bringing up secondary CPUs ... [ 0.200453] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.200671] smp: Brought up 1 node, 2 CPUs [ 0.200705] SMP: Total of 2 processors activated (76.80 BogoMIPS). [ 0.200725] CPU: All CPU(s) started in SVC mode. [ 0.202148] devtmpfs: initialized [ 0.211750] VFP support v0.3: implementor 51 architecture 64 part 6f variant 2 rev 0 [ 0.212072] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.212111] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.221586] pinctrl core: initialized pinctrl subsystem [ 0.222779] NET: Registered protocol family 16 [ 0.224668] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.225901] cpuidle: using governor menu [ 0.226527] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.226553] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.268095] vgaarb: loaded [ 0.268597] SCSI subsystem initialized [ 0.268816] libata version 3.00 loaded. [ 0.269096] usbcore: registered new interface driver usbfs [ 0.269185] usbcore: registered new interface driver hub [ 0.269290] usbcore: registered new device driver usb [ 0.270505] Advanced Linux Sound Architecture Driver Initialized. [ 0.271640] clocksource: Switched to clocksource arch_sys_counter [ 0.624778] NET: Registered protocol family 2 [ 0.625271] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.625313] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.625381] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.625472] TCP: Hash tables configured (established 8192 bind 8192) [ 0.625571] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.625610] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.625774] NET: Registered protocol family 1 [ 0.626294] RPC: Registered named UNIX socket transport module. [ 0.626319] RPC: Registered udp transport module. [ 0.626341] RPC: Registered tcp transport module. [ 0.626363] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.626390] PCI: CLS 0 bytes, default 64 [ 0.626644] Trying to unpack rootfs image as initramfs... [ 0.830413] Freeing initrd memory: 40224K [ 0.831171] hw perfevents: enabled with armv7_krait PMU driver, 5 counters available [ 0.833228] Initialise system trusted keyrings [ 0.833427] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.840496] NFS: Registering the id_resolver key type [ 0.840532] Key type id_resolver registered [ 0.840554] Key type id_legacy registered [ 0.841204] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.841533] fuse: init (API version 7.30) [ 0.841996] Key type asymmetric registered [ 0.842019] Asymmetric key parser 'x509' registered [ 0.842090] bounce: pool size: 64 pages [ 0.842145] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 0.842172] io scheduler mq-deadline registered [ 0.842195] io scheduler kyber registered [ 0.865206] msm_serial f991d000.serial: msm_serial: detected port #0 [ 0.865268] msm_serial f991d000.serial: uartclk = 7372800 [ 0.865339] f991d000.serial: ttyMSM0 at MMIO 0xf991d000 (irq = 27, base_baud = 460800) is a MSM [ 0.865386] msm_serial: console setup on port #0 [ 1.437147] printk: console [ttyMSM0] enabled [ 1.442335] msm_serial: driver initialized [ 1.446406] [drm:drm_core_init] Initialized [ 1.450208] [drm:msm_drm_register] init [ 1.454316] [drm:msm_mdp_register] [ 1.458422] [drm:msm_dsi_register] [ 1.461972] [drm:msm_edp_register] [ 1.466480] [drm:mdp5_dev_probe] [ 1.469612] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517 [ 1.472059] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator [ 1.495818] brd: module loaded [ 1.505768] loop: module loaded [ 1.506371] SCSI Media Changer driver v0.25 [ 1.508855] spmi spmi-0: PMIC arbiter version v1 (0x20000002) [ 1.521054] GPIO line 360 (otg-gpio) hogged as output/high [ 1.526208] s1: supplied by regulator-dummy [ 1.526582] s2: supplied by regulator-dummy [ 1.529836] s3: supplied by regulator-dummy [ 1.534087] s4: Bringing 5100000uV into 5000000-5000000uV [ 1.538148] l1: supplied by regulator-dummy [ 1.543792] l2: supplied by regulator-dummy [ 1.547731] l3: supplied by regulator-dummy [ 1.551921] l4: supplied by regulator-dummy [ 1.556056] l5: supplied by regulator-dummy [ 1.560244] l6: supplied by regulator-dummy [ 1.564423] l7: supplied by regulator-dummy [ 1.568574] l8: supplied by regulator-dummy [ 1.572765] l9: supplied by regulator-dummy [ 1.576904] l10: supplied by regulator-dummy [ 1.581084] l11: supplied by regulator-dummy [ 1.585616] l12: supplied by regulator-dummy [ 1.589867] l13: supplied by regulator-dummy [ 1.594118] l14: supplied by regulator-dummy [ 1.598358] l15: supplied by regulator-dummy [ 1.602654] l16: supplied by regulator-dummy [ 1.606863] l17: supplied by regulator-dummy [ 1.611131] l18: supplied by regulator-dummy [ 1.615392] l19: supplied by regulator-dummy [ 1.619644] l20: supplied by regulator-dummy [ 1.623921] l21: supplied by regulator-dummy [ 1.628145] l22: supplied by regulator-dummy [ 1.632434] l23: supplied by regulator-dummy [ 1.636651] l24: supplied by regulator-dummy [ 1.640922] lvs1: supplied by regulator-dummy [ 1.645125] lvs2: supplied by regulator-dummy [ 1.649354] lvs3: supplied by regulator-dummy [ 1.653899] 5vs1: supplied by s4 [ 1.658101] 5vs2: supplied by s4 [ 1.662570] libphy: Fixed MDIO Bus: probed [ 1.664506] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled). [ 1.668154] CSLIP: code copyright 1989 Regents of the University of California. [ 1.677881] usbcore: registered new interface driver ax88179_178a [ 1.685059] usbcore: registered new interface driver cdc_ether [ 1.691285] usbcore: registered new interface driver net1080 [ 1.697033] usbcore: registered new interface driver cdc_subset [ 1.702884] usbcore: registered new interface driver cdc_ncm [ 1.708638] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.714366] ehci-pci: EHCI PCI platform driver [ 1.720772] usbcore: registered new interface driver cdc_acm [ 1.725110] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.746239] rtc-pm8xxx fc4cf000.spmi:pm8941@0:rtc@6000: registered as rtc0 [ 1.746476] i2c /dev entries driver [ 1.752325] i2c_qup f9923000.i2c: tx channel not available [ 1.756240] i2c_qup f9925000.i2c: tx channel not available [ 1.770247] lm3630a_bl 2-0038: LM3630A backlight register OK. [ 1.770594] i2c_qup f9968000.i2c: tx channel not available [ 1.776699] qcom-smbb fc4cf000.spmi:pm8941@0:charger@1000: Initializing SMBB rev 3 [ 1.786344] otg-vbus: supplied by 5vs1 [ 1.790745] qcom-tsens fc4a9000.thermal-sensor: tsens calibration failed [ 1.794029] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations [ 1.800615] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations [ 1.807900] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations [ 1.814941] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations [ 1.822673] sdhci: Secure Digital Host Controller Interface driver [ 1.829350] sdhci: Copyright(c) Pierre Ossman [ 1.835628] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.842527] usbcore: registered new interface driver usbhid [ 1.845757] usbhid: USB HID core driver [ 1.854207] oprofile: using timer interrupt. [ 1.855073] NET: Registered protocol family 17 [ 1.859449] Key type dns_resolver registered [ 1.864071] Registering SWP/SWPB emulation handler [ 1.868651] Loading compiled-in X.509 certificates [ 1.903305] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517 [ 1.903386] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator [ 1.931752] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517 [ 1.931862] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator [ 1.954303] s1: supplied by regulator-dummy [ 1.954396] s1: Bringing 0uV into 675000-675000uV [ 1.961140] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517 [ 1.962969] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator [ 1.974984] s2: supplied by regulator-dummy [ 1.986512] s2: Bringing 0uV into 500000-500000uV [ 1.990426] s3: supplied by regulator-dummy [ 1.995072] s3: Bringing 0uV into 1050000-1050000uV [ 1.999485] s4: supplied by regulator-dummy [ 2.003931] s4: Bringing 0uV into 815000-815000uV [ 2.008301] s5: supplied by regulator-dummy [ 2.013266] s6: supplied by regulator-dummy [ 2.017204] s7: supplied by regulator-dummy [ 2.021371] s8: supplied by regulator-dummy [ 2.025952] s1: supplied by regulator-dummy [ 2.029413] s1: Bringing 0uV into 1300000-1300000uV [ 2.036531] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517 [ 2.038422] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator [ 2.050730] s2: supplied by regulator-dummy [ 2.062206] s2: Bringing 0uV into 2150000-2150000uV [ 2.066310] s3: supplied by regulator-dummy [ 2.070734] s3: Bringing 0uV into 1800000-1800000uV [ 2.076623] input: soc:gpio-keys as /devices/platform/soc/soc:gpio-keys/input/input0 [ 2.080214] rtc-pm8xxx fc4cf000.spmi:pm8941@0:rtc@6000: setting system clock to 1970-01-25T07:16:55 UTC (2099815) [ 2.089736] wl-reg: disabling [ 2.090219] l1: supplied by s1 [ 2.098016] ALSA device list: [ 2.100860] l1: Bringing 0uV into 1225000-1225000uV [ 2.103779] No soundcards found. [ 2.107214] l2: supplied by s3 [ 2.115377] l2: Bringing 0uV into 1200000-1200000uV [ 2.115928] l3: supplied by s1 [ 2.116580] Freeing unused kernel memory: 1024K [ 2.119130] l3: Bringing 0uV into 1225000-1225000uV [ 2.126986] l4: supplied by s1 [ 2.134682] l4: Bringing 0uV into 1225000-1225000uV [ 2.137938] l5: supplied by s2 [ 2.142596] l5: Bringing 0uV into 1800000-1800000uV [ 2.145923] l6: supplied by s2 [ 2.150452] l6: Bringing 0uV into 1800000-1800000uV [ 2.154552] l7: supplied by s2 [ 2.158357] l7: Bringing 0uV into 1800000-1800000uV [ 2.161841] l8: supplied by vph-pwr [ 2.166248] l8: Bringing 0uV into 1800000-1800000uV [ 2.170238] l9: supplied by vreg-boost [ 2.174715] Run /init as init process [ 2.174780] l9: Bringing 0uV into 1800000-1800000uV [ 2.182142] mmc0: SDHCI controller on f98a4900.sdhci [f98a4900.sdhci] using ADMA [ 2.187703] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517 [ 2.194818] l10: supplied by vreg-boost [ 2.206363] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator [ 2.210753] l10: Bringing 0uV into 1800000-1800000uV [ 2.221617] l11: supplied by s1 [ 2.230312] l11: Bringing 0uV into 1300000-1300000uV [ 2.235025] l12: supplied by s2 [ 2.239432] l12: Bringing 0uV into 1800000-1800000uV [ 2.242907] l13: supplied by vreg-boost [ 2.247724] l13: Bringing 0uV into 1800000-1800000uV [ 2.251575] l14: supplied by s2 [ 2.256385] l14: Bringing 0uV into 1800000-1800000uV [ 2.259634] l15: supplied by s2 [ 2.264420] l15: Bringing 0uV into 2050000-2050000uV [ 2.267535] l16: supplied by vph-pwr [ 2.272518] l16: Bringing 0uV into 2700000-2700000uV [ 2.276242] l17: supplied by vreg-boost [ 2.280917] l17: Bringing 0uV into 2850000-2850000uV [ 2.284949] l18: supplied by vph-pwr [ 2.289734] l18: Bringing 0uV into 2850000-2850000uV [ 2.293620] l19: supplied by vph-pwr [ 2.298259] l19: Bringing 0uV into 3000000-3000000uV [ 2.302203] l20: supplied by vreg-boost [ 2.306749] l20: Bringing 0uV into 2950000-2950000uV [ 2.310787] l21: supplied by vreg-boost [ 2.315548] l21: Bringing 0uV into 2950000-2950000uV [ 2.319567] l22: supplied by vreg-boost [ 2.324319] l22: Bringing 0uV into 3000000-3000000uV [ 2.328183] l23: supplied by vreg-boost [ 2.333080] l23: Bringing 0uV into 3000000-3000000uV [ 2.336953] l24: supplied by vreg-boost [ 2.341876] l24: Bringing 0uV into 3075000-3075000uV [ 2.346008] lvs1: supplied by s3 [ 2.350968] lvs2: supplied by s3 [ 2.354222] lvs3: supplied by s3 [ 2.357474] 5vs1: supplied by regulator-dummy [ 2.360653] 5vs2: supplied by regulator-dummy [ 2.367752] random: fast init done [ 2.371038] mmc0: new ultra high speed SDR104 SDIO card at address 0001 [ 2.373113] [drm:pll_28nm_register] 0 [ 2.378626] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_dc_off = 9 [ 2.382375] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_freq_seed = 31289 [ 2.388077] [drm:dsi_pll_28nm_clk_recalc_rate] vco rate = 402333398 [ 2.394525] [drm:dsi_pll_28nm_clk_recalc_rate] returning vco rate = 402333398 [ 2.401711] [drm:msm_dsi_pll_init] DSI:0 PLL registered [ 2.448289] mmc1: SDHCI controller on f9824900.sdhci [f9824900.sdhci] using ADMA [ 2.448730] [drm:mdp5_mdss_init] [ 2.455563] [drm:mdp5_bind] [ 2.458257] [drm:get_clk] skipping lut [ 2.461016] [drm:msm_runtime_resume] [ 2.464538] [drm:mdp5_mdss_enable] [ 2.468324] [drm:mdp5_runtime_resume] [ 2.471553] [drm:mdp5_enable] [ 2.475559] [drm:mdp5_runtime_suspend] [ 2.478538] [drm:mdp5_disable] [ 2.482321] msm_mdp fd900100.mdp: [drm:mdp5_bind] MDP5 version v1.2 [ 2.485404] [drm:mdp5_cfg_init] MDP5: msm8x74 hw config selected [ 2.491686] [drm:mdp5_ctlm_init] Pool of 5 CTLs created. [ 2.497932] msm fd900000.mdss: bound fd900100.mdp (ops mdp5_ops) [ 2.503229] [drm:dsi_bind] [ 2.509184] [drm:dsi_bind] dsi probed=(ptrval) [ 2.511936] msm_dsi fd922800.dsi: fd922800.dsi supply gdsc not found, using dummy regulator [ 2.516320] [drm:msm_dsi_host_init] dsi_get_config: Version 3:10010000 [ 2.524587] msm_dsi fd922800.dsi: fd922800.dsi supply gdsc not found, using dummy regulator [ 2.532920] [drm:msm_dsi_host_init] Dsi Host 0 initialized [ 2.540829] [drm:msm_dsi_runtime_resume] id=0 [ 2.546386] panel-simple-dsi fd922800.dsi.0: fd922800.dsi.0 supply power not found, using dummy regulator [ 2.550819] [drm:dsi_host_attach] id=0 [ 2.560278] msm fd900000.mdss: bound fd922800.dsi (ops dsi_ops) [ 2.563869] [drm] using 16m VRAM carveout [ 2.569691] [drm:msm_dsi_runtime_suspend] [ 2.579129] msm fd900000.mdss: [drm:msm_drm_bind] VRAM: 20100000->21100000 [ 2.579284] [drm:mdp5_runtime_resume] [ 2.584944] [drm:mdp5_enable] [ 2.595290] mmc1: new HS200 MMC card at address 0001 [ 2.596083] mmcblk1: mmc1:0001 SEM16G 14.7 GiB [ 2.599616] mmcblk1boot0: mmc1:0001 SEM16G partition 1 4.00 MiB [ 2.611955] mmcblk1boot1: mmc1:0001 SEM16G partition 2 4.00 MiB [ 2.612178] mmcblk1rpmb: mmc1:0001 SEM16G partition 3 4.00 MiB, chardev (247:0) [ 2.617161] msm_mdp fd900100.mdp: [drm:mdp5_kms_init] no iommu, fallback to phys contig buffers for scanout [ 2.624150] [drm:mdp5_runtime_suspend] [ 2.633911] [drm:mdp5_disable] [ 2.637722] msm fd900000.mdss: fall back to the other CTL category for INTF 1! [ 2.640653] [drm:mdp5_ctlm_request] CTL 0 allocated [ 2.648547] [drm:mdp5_runtime_resume] [ 2.653040] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 [ 2.659516] [drm:mdp5_enable] [ 2.672935] [drm:mdp5_runtime_suspend] [ 2.672969] [drm:mdp5_disable] [ 2.675763] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.678704] [drm] Driver supports precise vblank timestamp query. [ 2.685346] [drm:drm_irq_install] irq=78 [ 2.691558] [drm:mdp5_runtime_resume] [ 2.695572] [drm:mdp5_enable] [ 2.699132] [drm:mdp5_runtime_suspend] [ 2.702167] [drm:mdp5_disable] [ 2.705932] [drm:mdp5_runtime_resume] [ 2.708996] [drm:mdp5_enable] [ 2.712878] [drm:mdp5_runtime_suspend] [ 2.715855] [drm:mdp5_disable] [ 2.719602] [drm:drm_minor_register] [ 2.723028] [drm:drm_minor_register] new minor registered 128 [ 2.726537] [drm:drm_minor_register] [ 2.732556] [drm:drm_minor_register] new minor registered 0 [ 2.736029] [drm:drm_sysfs_connector_add] adding "DSI-1" to sysfs [ 2.741296] [drm:drm_sysfs_hotplug_event] generating hotplug event [ 2.747642] [drm] Initialized msm 1.5.0 20130625 for fd900000.mdss on minor 0 [ 2.753657] [drm:drm_mode_object_get] OBJ ID: 31 (2) [ 2.760825] [drm:drm_setup_crtcs] [ 2.765883] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:31:DSI-1] [ 2.769079] [drm:dsi_mgr_connector_detect] id=0 [ 2.776303] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:31:DSI-1] status updated from unknown to connected [ 2.780725] [drm:dsi_mgr_connector_mode_valid] [ 2.791490] [drm:dsi_mgr_connector_mode_valid] requested=150000000, actual=150000000 [ 2.796056] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:31:DSI-1] probed modes : [ 2.804007] [drm:drm_mode_debug_printmodeline] Modeline "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0 [ 2.812427] [drm:drm_setup_crtcs] connector 31 enabled? yes [ 2.823697] [drm:drm_setup_crtcs] Not using firmware configuration [ 2.829233] [drm:drm_setup_crtcs] looking for cmdline mode on connector 31 [ 2.835510] [drm:drm_setup_crtcs] looking for preferred mode on connector 31 0 [ 2.842363] [drm:drm_setup_crtcs] found mode 1080x1920 [ 2.849539] [drm:drm_setup_crtcs] picking CRTCs for 65535x65535 config [ 2.854690] [drm:drm_setup_crtcs] desired mode 1080x1920 set on crtc 49 (0,0) [ 2.861197] [drm:drm_mode_object_get] OBJ ID: 31 (2) [ 2.868418] [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane [ 2.873457] [drm:msm_fbdev_create] create fbdev: 1080x1920@32 (1080x1920) [ 2.881142] [drm:msm_alloc_stolen_fb] allocating 8355840 bytes for fb 0 [ 2.888552] [drm:msm_framebuffer_init] create framebuffer: dev=(ptrval), mode_cmd=(ptrval) (1080x1920@XR24) [ 2.894379] [drm:msm_framebuffer_init] create: FB ID: 50 ((ptrval)) [ 2.904088] [drm:msm_fbdev_create] fbi=(ptrval), dev=(ptrval) [ 2.910401] [drm:msm_fbdev_create] par=(ptrval), 1080x1920 [ 2.916232] [drm:msm_fbdev_create] allocated 1080x1920 fb [ 2.922042] [drm:drm_atomic_state_init] Allocated atomic state (ptrval) [ 2.922064] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval) [ 2.922081] [drm:drm_atomic_get_plane_state] Added [PLANE:35:plane-1] (ptrval) state to (ptrval) [ 2.922095] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:35:plane-1] state (ptrval) [ 2.922112] [drm:drm_atomic_get_plane_state] Added [PLANE:37:plane-2] (ptrval) state to (ptrval) [ 2.922125] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:37:plane-2] state (ptrval) [ 2.922142] [drm:drm_atomic_get_plane_state] Added [PLANE:39:plane-3] (ptrval) state to (ptrval) [ 2.922154] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:39:plane-3] state (ptrval) [ 2.922170] [drm:drm_atomic_get_plane_state] Added [PLANE:41:plane-4] (ptrval) state to (ptrval) [ 2.922183] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:41:plane-4] state (ptrval) [ 2.922199] [drm:drm_atomic_get_plane_state] Added [PLANE:43:plane-5] (ptrval) state to (ptrval) [ 2.922212] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:43:plane-5] state (ptrval) [ 2.922228] [drm:drm_atomic_get_plane_state] Added [PLANE:45:plane-6] (ptrval) state to (ptrval) [ 2.922241] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:45:plane-6] state (ptrval) [ 2.922257] [drm:drm_atomic_get_plane_state] Added [PLANE:47:plane-7] (ptrval) state to (ptrval) [ 2.922270] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:47:plane-7] state (ptrval) [ 2.922288] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval) [ 2.922308] [drm:drm_atomic_set_mode_for_crtc] Set [MODE:1080x1920] for [CRTC:49:crtc-0] state (ptrval) [ 2.922325] [drm:drm_atomic_set_crtc_for_plane] Link [PLANE:32:plane-0] state (ptrval) to [CRTC:49:crtc-0] [ 2.922339] [drm:drm_atomic_set_fb_for_plane] Set [FB:50] for [PLANE:32:plane-0] state (ptrval) [ 2.922350] [drm:drm_mode_object_get] OBJ ID: 50 (1) [ 2.922368] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval) [ 2.922384] [drm:drm_mode_object_get] OBJ ID: 31 (3) [ 2.922399] [drm:drm_atomic_get_connector_state] Added [CONNECTOR:31:DSI-1] (ptrval) state to (ptrval) [ 2.922410] [drm:drm_mode_object_get] OBJ ID: 31 (4) [ 2.922427] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [CRTC:49:crtc-0] [ 2.922439] [drm:drm_atomic_check_only] checking (ptrval) [ 2.922460] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] mode changed [ 2.922473] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] enable changed [ 2.922486] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] active changed [ 2.922497] [drm:dsi_mgr_connector_best_encoder] [ 2.922513] [drm:drm_atomic_helper_check_modeset] Updating routing for [CONNECTOR:31:DSI-1] [ 2.922523] [drm:dsi_mgr_connector_best_encoder] [ 2.922544] [drm:drm_atomic_helper_check_modeset] [CONNECTOR:31:DSI-1] using [ENCODER:30:DSI-30] on [CRTC:49:crtc-0] [ 2.922559] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] needs all connectors, enable: y, active: y [ 2.922575] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval) [ 2.922593] [drm:drm_atomic_add_affected_planes] Adding all current planes for [CRTC:49:crtc-0] to (ptrval) [ 2.922610] [drm:drm_atomic_normalize_zpos] [CRTC:49:crtc-0] calculating normalized zpos values [ 2.922625] [drm:drm_atomic_normalize_zpos] [PLANE:32:plane-0] processing zpos value 0 [ 2.922639] [drm:drm_atomic_normalize_zpos] [PLANE:32:plane-0] normalized zpos value 0 [ 2.922654] [drm:mdp5_plane_atomic_check] plane-0: check (0 -> 0) [ 2.922678] [drm:drm_atomic_get_private_obj_state] Added new private object (ptrval) state (ptrval) to (ptrval) [ 2.922694] [drm:mdp5_pipe_assign] DMA0: alloc SMP blocks [ 2.922708] [drm:mdp5_smp_assign] DMA0[0]: request 3 SMP blocks [ 2.922724] [drm:mdp5_pipe_assign] DMA0: assign to plane plane-0 for caps 0 [ 2.922740] [drm:mdp5_crtc_atomic_check] crtc-0: check [ 2.922755] [drm:mdp5_mixer_assign] assigning Layer Mixer 0 to crtc crtc-0 [ 2.922772] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1 [ 2.922785] [drm:drm_atomic_commit] committing (ptrval) [ 2.922806] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0) [ 2.922828] [drm:mdp5_runtime_resume] [ 2.922839] [drm:mdp5_enable] [ 2.922884] [drm:mdp5_smp_prepare_commit] assign DMA0:0, 3 blks [ 2.922896] [drm:mdp5_smp_prepare_commit] assign DMA0:1, 3 blks [ 2.922908] [drm:mdp5_smp_prepare_commit] assign DMA0:2, 3 blks [ 2.922951] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920 [ 2.922964] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240 [ 2.922980] [drm:drm_atomic_helper_commit_modeset_disables] modeset on [CRTC:49:crtc-0] [ 2.923000] [drm:mdp5_crtc_mode_set_nofb] crtc-0: set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0 [ 2.923018] [drm:drm_atomic_helper_commit_modeset_disables] modeset on [ENCODER:30:DSI-30] [ 2.923036] [drm:dsi_mgr_bridge_mode_set] set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0 [ 2.923050] [drm:drm_atomic_helper_commit_planes] crtc-0: begin [ 2.923062] [drm:mdp5_plane_atomic_update] plane-0: update [ 2.923078] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920 [ 2.923090] [drm:mdp5_plane_mode_set] scale config = 0 [ 2.923117] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval) [ 2.923146] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000 [ 2.923161] [drm:crtc_flush] crtc-0: flush=00000840 [ 2.923179] [drm:drm_atomic_helper_commit_modeset_enables] enabling [CRTC:49:crtc-0] [ 2.923192] [drm:mdp5_crtc_atomic_enable] crtc-0 [ 2.923210] [drm:drm_crtc_vblank_on] crtc 0, vblank enabled 0, inmodeset 0 [ 2.923238] [drm:mdp5_crtc_mode_set_nofb] crtc-0: set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0 [ 2.923260] [drm:drm_atomic_helper_commit_modeset_enables] enabling [ENCODER:30:DSI-30] [ 2.923272] [drm:dsi_mgr_bridge_pre_enable] id=0 [ 2.923282] [drm:msm_dsi_host_reset_phy] [ 2.927146] [drm:dsi_calc_clk_rate_6g] pclk=150000000, bclk=112500000 [ 2.927161] [drm:msm_dsi_phy_enable] [ 2.927366] [drm:dsi_28nm_phy_enable] [ 2.927384] [drm:msm_dsi_dphy_timing_calc] PHY timings: 44, 2, 0, 238, 56, 38, 106, 108, 44, 60, 44 [ 2.927428] [drm:msm_dsi_host_power_on] [ 2.928075] [drm:msm_dsi_runtime_resume] id=0 [ 2.928101] [drm:dsi_link_clk_enable_6g] Set clk rates: pclk=150000, byteclk=112500000 [ 2.928170] [drm:dsi_pll_28nm_clk_set_rate] refclk_cfg = 1 [ 2.928182] [drm:dsi_pll_28nm_clk_set_rate] div_fb = 11718 [ 2.928193] [drm:dsi_pll_28nm_clk_set_rate] frac_n_value = 47054 [ 2.928204] [drm:dsi_pll_28nm_clk_set_rate] Generated VCO Clock: 449971200 [ 2.928215] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg0=0 [ 2.928226] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg1=74 [ 2.928237] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg2=206 [ 2.928248] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg3=183 [ 2.928260] [drm:dsi_pll_28nm_clk_set_rate] cal_cfg10=193, cal_cfg11=1 [ 2.928285] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_dc_off = 10 [ 2.928297] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_freq_seed = 47054 [ 2.928308] [drm:dsi_pll_28nm_clk_recalc_rate] vco rate = 449970703 [ 2.928320] [drm:dsi_pll_28nm_clk_recalc_rate] returning vco rate = 449970703 [ 2.928394] [drm:dsi_pll_28nm_enable_seq_hpm] id=0 [ 2.930017] [drm:pll_28nm_poll_for_ready] DSI PLL is locked [ 2.930027] [drm:dsi_pll_28nm_enable_seq_hpm] DSI PLL Lock success [ 2.930040] [drm:msm_dsi_pll_helper_clk_prepare] DSI PLL locked after sequence #1 [ 2.930061] [drm:msm_dsi_host_power_on] [ 2.930078] [drm:dsi_intr_ctrl] intr=2000000 enable=1 [ 2.930090] [drm:msm_dsi_host_power_on] lane number=4 [ 2.930107] [drm:dsi_intr_ctrl] intr=2000200 enable=1 [ 2.930126] [drm:mdp5_cmd_encoder_mode_set] set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0 [ 2.930157] [drm:mdp5_crtc_vblank_irq] crtc-0: send event: (ptrval) [ 2.930199] [drm:mdp5_ctl_set_encoder_state] intf_1: on [ 2.930214] [drm:drm_bridge_enable] [ 2.930227] [drm:msm_enable_vblank] dev=(ptrval), crtc=0 [ 2.930247] [drm:drm_vblank_enable] enabling vblank on crtc 0, ret: 0 [ 2.930266] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0 [ 2.981842] msm fd900000.mdss: pp done time out, lm=0 [ 3.041732] ------------[ cut here ]------------ [ 3.041751] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 [ 3.041759] [CRTC:49:crtc-0] vblank wait timed out [ 3.041764] Modules linked in: [ 3.041784] CPU: 0 PID: 100 Comm: kworker/0:2 Not tainted 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303 [ 3.041792] Hardware name: Generic DT based system [ 3.041812] Workqueue: events deferred_probe_work_func [ 3.041839] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14) [ 3.041853] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c) [ 3.041871] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4) [ 3.041884] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88) [ 3.041899] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290) [ 3.041916] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40) [ 3.041937] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140) [ 3.041952] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c) [ 3.041963] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128) [ 3.041973] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4) [ 3.041985] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c076a7d0>] (drm_fb_helper_restore_fbdev_mode_unlocked+0x54/0xa4) [ 3.041996] [<c076a7d0>] (drm_fb_helper_restore_fbdev_mode_unlocked) from [<c076a850>] (drm_fb_helper_set_par+0x30/0x54) [ 3.042007] [<c076a850>] (drm_fb_helper_set_par) from [<c06ef4c8>] (fbcon_init+0x4b4/0x5d4) [ 3.042019] [<c06ef4c8>] (fbcon_init) from [<c073bf88>] (visual_init+0xbc/0x104) [ 3.042030] [<c073bf88>] (visual_init) from [<c073dea8>] (do_bind_con_driver+0x1ec/0x3c4) [ 3.042040] [<c073dea8>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0) [ 3.042050] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8) [ 3.042066] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80) [ 3.042078] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68) [ 3.042094] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304) [ 3.042106] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c) [ 3.042120] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc) [ 3.042131] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634) [ 3.042146] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4) [ 3.042160] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174) [ 3.042175] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98) [ 3.042188] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c) [ 3.042200] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0) [ 3.042211] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4) [ 3.042222] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168) [ 3.042232] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c) [ 3.042243] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4) [ 3.042259] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564) [ 3.042273] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584) [ 3.042285] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150) [ 3.042297] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 3.042306] Exception stack(0xc4e09fb0 to 0xc4e09ff8) [ 3.042325] 9fa0: 00000000 00000000 00000000 00000000 [ 3.042350] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 3.042371] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 3.042380] ---[ end trace d4b922f6bb6a2602 ]--- [ 3.042416] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval) [ 3.042430] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (5) [ 3.042451] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval) [ 3.042514] [drm:drm_atomic_state_init] Allocated atomic state (ptrval) [ 3.042528] [drm:drm_mode_object_get] OBJ ID: 50 (2) [ 3.042543] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval) [ 3.042556] [drm:drm_mode_object_get] OBJ ID: 51 (1) [ 3.042571] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval) [ 3.042588] [drm:drm_atomic_get_plane_state] Added [PLANE:35:plane-1] (ptrval) state to (ptrval) [ 3.042601] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:35:plane-1] state (ptrval) [ 3.042617] [drm:drm_atomic_get_plane_state] Added [PLANE:37:plane-2] (ptrval) state to (ptrval) [ 3.042630] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:37:plane-2] state (ptrval) [ 3.042646] [drm:drm_atomic_get_plane_state] Added [PLANE:39:plane-3] (ptrval) state to (ptrval) [ 3.042659] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:39:plane-3] state (ptrval) [ 3.042675] [drm:drm_atomic_get_plane_state] Added [PLANE:41:plane-4] (ptrval) state to (ptrval) [ 3.042687] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:41:plane-4] state (ptrval) [ 3.042703] [drm:drm_atomic_get_plane_state] Added [PLANE:43:plane-5] (ptrval) state to (ptrval) [ 3.042716] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:43:plane-5] state (ptrval) [ 3.042732] [drm:drm_atomic_get_plane_state] Added [PLANE:45:plane-6] (ptrval) state to (ptrval) [ 3.042745] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:45:plane-6] state (ptrval) [ 3.042761] [drm:drm_atomic_get_plane_state] Added [PLANE:47:plane-7] (ptrval) state to (ptrval) [ 3.042774] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:47:plane-7] state (ptrval) [ 3.042789] [drm:drm_atomic_set_fb_for_plane] Set [FB:50] for [PLANE:32:plane-0] state (ptrval) [ 3.042800] [drm:drm_mode_object_get] OBJ ID: 50 (3) [ 3.042812] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (4) [ 3.042828] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval) [ 3.042843] [drm:drm_mode_object_get] OBJ ID: 31 (5) [ 3.042854] [drm:drm_mode_object_get] OBJ ID: 31 (6) [ 3.042869] [drm:drm_atomic_get_connector_state] Added [CONNECTOR:31:DSI-1] (ptrval) state to (ptrval) [ 3.042882] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6) [ 3.042896] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [NOCRTC] [ 3.042907] [drm:drm_mode_object_get] OBJ ID: 31 (5) [ 3.042924] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [CRTC:49:crtc-0] [ 3.042936] [drm:drm_atomic_check_only] checking (ptrval) [ 3.042949] [drm:dsi_mgr_connector_best_encoder] [ 3.042967] [drm:drm_atomic_helper_check_modeset] Updating routing for [CONNECTOR:31:DSI-1] [ 3.042976] [drm:dsi_mgr_connector_best_encoder] [ 3.042996] [drm:drm_atomic_helper_check_modeset] [CONNECTOR:31:DSI-1] keeps [ENCODER:30:DSI-30], now on [CRTC:49:crtc-0] [ 3.043012] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1) [ 3.043031] [drm:mdp5_crtc_atomic_check] crtc-0: check [ 3.043047] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1 [ 3.043060] [drm:drm_atomic_commit] committing (ptrval) [ 3.043078] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0) [ 3.043135] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920 [ 3.043148] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240 [ 3.043162] [drm:drm_atomic_helper_commit_planes] crtc-0: begin [ 3.043173] [drm:mdp5_plane_atomic_update] plane-0: update [ 3.043188] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920 [ 3.043199] [drm:mdp5_plane_mode_set] scale config = 0 [ 3.043223] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval) [ 3.043249] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000 [ 3.043263] [drm:crtc_flush] crtc-0: flush=00000840 [ 3.043304] [drm:drm_atomic_state_init] Allocated atomic state (ptrval) [ 3.101745] msm fd900000.mdss: pp done time out, lm=0 [ 3.161729] ------------[ cut here ]------------ [ 3.161746] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 [ 3.161754] [CRTC:49:crtc-0] vblank wait timed out [ 3.161758] Modules linked in: [ 3.161778] CPU: 0 PID: 100 Comm: kworker/0:2 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303 [ 3.161786] Hardware name: Generic DT based system [ 3.161803] Workqueue: events deferred_probe_work_func [ 3.161820] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14) [ 3.161831] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c) [ 3.161844] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4) [ 3.161856] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88) [ 3.161870] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290) [ 3.161885] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40) [ 3.161900] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140) [ 3.161914] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c) [ 3.161926] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128) [ 3.161936] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4) [ 3.161945] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c0766c48>] (drm_fb_helper_pan_display+0xc4/0x1d8) [ 3.161957] [<c0766c48>] (drm_fb_helper_pan_display) from [<c06e7c38>] (fb_pan_display+0x9c/0x110) [ 3.161969] [<c06e7c38>] (fb_pan_display) from [<c06f3528>] (bit_update_start+0x14/0x30) [ 3.161979] [<c06f3528>] (bit_update_start) from [<c06f215c>] (fbcon_switch+0x390/0x514) [ 3.161989] [<c06f215c>] (fbcon_switch) from [<c073d5d4>] (redraw_screen+0x13c/0x244) [ 3.161999] [<c073d5d4>] (redraw_screen) from [<c06eef84>] (fbcon_prepare_logo+0x378/0x408) [ 3.162007] [<c06eef84>] (fbcon_prepare_logo) from [<c06ef438>] (fbcon_init+0x424/0x5d4) [ 3.162016] [<c06ef438>] (fbcon_init) from [<c073bf88>] (visual_init+0xbc/0x104) [ 3.162025] [<c073bf88>] (visual_init) from [<c073dea8>] (do_bind_con_driver+0x1ec/0x3c4) [ 3.162035] [<c073dea8>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0) [ 3.162044] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8) [ 3.162057] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80) [ 3.162067] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68) [ 3.162079] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304) [ 3.162091] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c) [ 3.162105] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc) [ 3.162116] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634) [ 3.162129] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4) [ 3.162142] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174) [ 3.162155] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98) [ 3.162167] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c) [ 3.162178] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0) [ 3.162189] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4) [ 3.162199] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168) [ 3.162210] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c) [ 3.162220] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4) [ 3.162233] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564) [ 3.162246] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584) [ 3.162258] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150) [ 3.162268] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 3.162277] Exception stack(0xc4e09fb0 to 0xc4e09ff8) [ 3.162295] 9fa0: 00000000 00000000 00000000 00000000 [ 3.162319] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 3.162340] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 3.162349] ---[ end trace d4b922f6bb6a2603 ]--- [ 3.162379] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50] [ 3.162397] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval) [ 3.162409] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6) [ 3.162421] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (5) [ 3.162433] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2) [ 3.162446] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3) [ 3.162461] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval) [ 3.162491] [drm:drm_mode_object_get] OBJ ID: 50 (2) [ 3.162507] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval) [ 3.162519] [drm:drm_mode_object_get] OBJ ID: 51 (1) [ 3.162535] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval) [ 3.162545] [drm:drm_mode_object_get] OBJ ID: 52 (1) [ 3.162558] [drm:drm_atomic_check_only] checking (ptrval) [ 3.162575] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1) [ 3.162592] [drm:mdp5_crtc_atomic_check] crtc-0: check [ 3.162609] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1 [ 3.162622] [drm:drm_atomic_commit] committing (ptrval) [ 3.162638] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0) [ 3.581980] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 4.109986] EXT4-fs (dm-0): mounted filesystem without journal. Opts: (null) [ 4.618939] [drm:mdp5_crtc_vblank_irq] crtc-0: send event: (ptrval) [ 4.618983] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0 [ 4.618998] [drm:vblank_disable_fn] disabling vblank on crtc 0 [ 4.619016] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0 [ 4.619029] [drm:msm_disable_vblank] dev=(ptrval), crtc=0 [ 4.619112] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920 [ 4.619126] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240 [ 4.619142] [drm:drm_atomic_helper_commit_planes] crtc-0: begin [ 4.619156] [drm:mdp5_plane_atomic_update] plane-0: update [ 4.619173] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920 [ 4.619185] [drm:mdp5_plane_mode_set] scale config = 0 [ 4.619212] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval) [ 4.619243] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000 [ 4.619257] [drm:crtc_flush] crtc-0: flush=00000840 [ 4.619277] [drm:msm_enable_vblank] dev=(ptrval), crtc=0 [ 4.619293] [drm:drm_vblank_enable] enabling vblank on crtc 0, ret: 0 [ 4.619311] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0 [ 4.620660] [drm:dsi_host_irq] isr=0x2000700, id=0 [ 4.671711] msm fd900000.mdss: pp done time out, lm=0 [ 4.731689] ------------[ cut here ]------------ [ 4.731716] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 [ 4.731724] [CRTC:49:crtc-0] vblank wait timed out [ 4.731729] Modules linked in: dm_mod [ 4.731757] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303 [ 4.731765] Hardware name: Generic DT based system [ 4.731782] Workqueue: events drm_fb_helper_dirty_work [ 4.731806] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14) [ 4.731820] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c) [ 4.731837] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4) [ 4.731849] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88) [ 4.731864] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290) [ 4.731885] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40) [ 4.731906] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140) [ 4.731921] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c) [ 4.731933] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128) [ 4.731948] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204) [ 4.731960] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164) [ 4.731975] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564) [ 4.731989] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584) [ 4.732002] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150) [ 4.732014] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 4.732023] Exception stack(0xde965fb0 to 0xde965ff8) [ 4.732042] 5fa0: 00000000 00000000 00000000 00000000 [ 4.732067] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 4.732088] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 4.732106] ---[ end trace d4b922f6bb6a2604 ]--- [ 4.732142] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50] [ 4.732160] [drm:drm_mode_object_put.part.0] OBJ ID: 52 (2) [ 4.732179] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval) [ 4.732192] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2) [ 4.732207] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3) [ 4.732222] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval) [ 4.758491] Console: switching to colour frame buffer device 135x120 [ 4.758533] [drm:drm_atomic_state_init] Allocated atomic state (ptrval) [ 4.758548] [drm:drm_mode_object_get] OBJ ID: 50 (2) [ 4.758564] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval) [ 4.758578] [drm:drm_mode_object_get] OBJ ID: 51 (1) [ 4.758594] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval) [ 4.758612] [drm:drm_atomic_get_plane_state] Added [PLANE:35:plane-1] (ptrval) state to (ptrval) [ 4.758626] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:35:plane-1] state (ptrval) [ 4.758643] [drm:drm_atomic_get_plane_state] Added [PLANE:37:plane-2] (ptrval) state to (ptrval) [ 4.758656] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:37:plane-2] state (ptrval) [ 4.758673] [drm:drm_atomic_get_plane_state] Added [PLANE:39:plane-3] (ptrval) state to (ptrval) [ 4.758686] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:39:plane-3] state (ptrval) [ 4.758703] [drm:drm_atomic_get_plane_state] Added [PLANE:41:plane-4] (ptrval) state to (ptrval) [ 4.758716] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:41:plane-4] state (ptrval) [ 4.758733] [drm:drm_atomic_get_plane_state] Added [PLANE:43:plane-5] (ptrval) state to (ptrval) [ 4.758746] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:43:plane-5] state (ptrval) [ 4.758763] [drm:drm_atomic_get_plane_state] Added [PLANE:45:plane-6] (ptrval) state to (ptrval) [ 4.758776] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:45:plane-6] state (ptrval) [ 4.759026] [drm:drm_atomic_get_plane_state] Added [PLANE:47:plane-7] (ptrval) state to (ptrval) [ 4.759040] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:47:plane-7] state (ptrval) [ 4.759057] [drm:drm_atomic_set_fb_for_plane] Set [FB:50] for [PLANE:32:plane-0] state (ptrval) [ 4.759069] [drm:drm_mode_object_get] OBJ ID: 50 (3) [ 4.759080] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (4) [ 4.759097] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval) [ 4.759114] [drm:drm_mode_object_get] OBJ ID: 31 (5) [ 4.759125] [drm:drm_mode_object_get] OBJ ID: 31 (6) [ 4.759140] [drm:drm_atomic_get_connector_state] Added [CONNECTOR:31:DSI-1] (ptrval) state to (ptrval) [ 4.759153] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6) [ 4.759168] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [NOCRTC] [ 4.759180] [drm:drm_mode_object_get] OBJ ID: 31 (5) [ 4.759196] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [CRTC:49:crtc-0] [ 4.759209] [drm:drm_atomic_check_only] checking (ptrval) [ 4.759224] [drm:dsi_mgr_connector_best_encoder] [ 4.759244] [drm:drm_atomic_helper_check_modeset] Updating routing for [CONNECTOR:31:DSI-1] [ 4.759254] [drm:dsi_mgr_connector_best_encoder] [ 4.759275] [drm:drm_atomic_helper_check_modeset] [CONNECTOR:31:DSI-1] keeps [ENCODER:30:DSI-30], now on [CRTC:49:crtc-0] [ 4.759293] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1) [ 4.759316] [drm:mdp5_crtc_atomic_check] crtc-0: check [ 4.759333] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1 [ 4.759347] [drm:drm_atomic_commit] committing (ptrval) [ 4.759369] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0) [ 4.759413] [drm:drm_atomic_state_init] Allocated atomic state (ptrval) [ 5.840800] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null) [ 8.871442] udevd[752]: starting version 3.2.7 [ 8.876350] random: udevd: uninitialized urandom read (16 bytes read) [ 8.877358] random: udevd: uninitialized urandom read (16 bytes read) [ 8.877459] random: udevd: uninitialized urandom read (16 bytes read) [ 8.908690] udevd[753]: starting eudev-3.2.7 [ 9.563857] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 9.588748] inv-mpu6050-i2c 3-0068: mounting matrix not found: using identity... [ 9.606791] input: pm8941_pwrkey as /devices/platform/soc/fc4cf000.spmi/spmi-0/0-00/fc4cf000.spmi:pm8941@0:pwrkey@800/input/input1 [ 9.679456] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 9.680082] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 9.680093] cfg80211: failed to load regulatory.db [ 9.797045] ak8975 4-000f: mounting matrix not found: using identity... [ 9.825968] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 [ 9.835347] brcmfmac mmc0:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.lge,hammerhead.txt failed with error -2 [ 10.163863] i2c i2c-3: Added multiplexed i2c bus 4 [ 12.344803] e cgroup1: Need name or subsystem set [ 12.682849] urandom_read: 2 callbacks suppressed [ 12.682860] random: mktemp: uninitialized urandom read (10 bytes read) [ 15.201752] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out [ 18.574025] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 19.368235] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 19.522781] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 19.955263] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 20.160328] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 20.395962] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 23.364779] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 24.303460] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 24.390171] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 25.441747] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:32:plane-0] flip_done timed out [ 25.441806] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920 [ 25.441820] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240 [ 25.441835] [drm:drm_atomic_helper_commit_planes] crtc-0: begin [ 25.441848] [drm:mdp5_plane_atomic_update] plane-0: update [ 25.441865] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920 [ 25.441877] [drm:mdp5_plane_mode_set] scale config = 0 [ 25.441909] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval) [ 25.441914] ------------[ cut here ]------------ [ 25.441928] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c:709 mdp5_crtc_atomic_flush+0x174/0x190 [ 25.441933] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod [ 25.442026] CPU: 0 PID: 100 Comm: kworker/0:2 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303 [ 25.442035] Hardware name: Generic DT based system [ 25.442054] Workqueue: events deferred_probe_work_func [ 25.442079] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14) [ 25.442094] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c) [ 25.442110] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4) [ 25.442124] [<c0321660>] (__warn.part.3) from [<c03217d8>] (warn_slowpath_null+0x44/0x4c) [ 25.442137] [<c03217d8>] (warn_slowpath_null) from [<c07ad97c>] (mdp5_crtc_atomic_flush+0x174/0x190) [ 25.442152] [<c07ad97c>] (mdp5_crtc_atomic_flush) from [<c075f5e0>] (drm_atomic_helper_commit_planes+0x1fc/0x270) [ 25.442172] [<c075f5e0>] (drm_atomic_helper_commit_planes) from [<c07ddd04>] (msm_atomic_commit_tail+0x44/0x140) [ 25.442187] [<c07ddd04>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c) [ 25.442198] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128) [ 25.442210] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4) [ 25.442219] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c0766c48>] (drm_fb_helper_pan_display+0xc4/0x1d8) [ 25.442234] [<c0766c48>] (drm_fb_helper_pan_display) from [<c06e7c38>] (fb_pan_display+0x9c/0x110) [ 25.442247] [<c06e7c38>] (fb_pan_display) from [<c06f3528>] (bit_update_start+0x14/0x30) [ 25.442257] [<c06f3528>] (bit_update_start) from [<c06f215c>] (fbcon_switch+0x390/0x514) [ 25.442269] [<c06f215c>] (fbcon_switch) from [<c073d5d4>] (redraw_screen+0x13c/0x244) [ 25.442280] [<c073d5d4>] (redraw_screen) from [<c073e010>] (do_bind_con_driver+0x354/0x3c4) [ 25.442291] [<c073e010>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0) [ 25.442300] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8) [ 25.442317] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80) [ 25.442329] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68) [ 25.442341] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304) [ 25.442354] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c) [ 25.442371] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc) [ 25.442383] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634) [ 25.442399] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4) [ 25.442412] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174) [ 25.442427] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98) [ 25.442441] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c) [ 25.442452] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0) [ 25.442463] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4) [ 25.442474] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168) [ 25.442484] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c) [ 25.442494] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4) [ 25.442510] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564) [ 25.442524] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584) [ 25.442537] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150) [ 25.442548] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 25.442558] Exception stack(0xc4e09fb0 to 0xc4e09ff8) [ 25.442577] 9fa0: 00000000 00000000 00000000 00000000 [ 25.442601] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 25.442623] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 25.442632] ---[ end trace d4b922f6bb6a2605 ]--- [ 25.442663] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000 [ 25.442677] [drm:crtc_flush] crtc-0: flush=00000840 [ 25.501752] msm fd900000.mdss: pp done time out, lm=0 [ 25.561740] ------------[ cut here ]------------ [ 25.561758] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 [ 25.561766] [CRTC:49:crtc-0] vblank wait timed out [ 25.561770] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod [ 25.561854] CPU: 0 PID: 100 Comm: kworker/0:2 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303 [ 25.561863] Hardware name: Generic DT based system [ 25.561879] Workqueue: events deferred_probe_work_func [ 25.561897] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14) [ 25.561908] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c) [ 25.561921] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4) [ 25.561933] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88) [ 25.561947] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290) [ 25.561963] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40) [ 25.561980] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140) [ 25.561993] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c) [ 25.562005] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128) [ 25.562015] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4) [ 25.562024] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c0766c48>] (drm_fb_helper_pan_display+0xc4/0x1d8) [ 25.562036] [<c0766c48>] (drm_fb_helper_pan_display) from [<c06e7c38>] (fb_pan_display+0x9c/0x110) [ 25.562047] [<c06e7c38>] (fb_pan_display) from [<c06f3528>] (bit_update_start+0x14/0x30) [ 25.562056] [<c06f3528>] (bit_update_start) from [<c06f215c>] (fbcon_switch+0x390/0x514) [ 25.562066] [<c06f215c>] (fbcon_switch) from [<c073d5d4>] (redraw_screen+0x13c/0x244) [ 25.562076] [<c073d5d4>] (redraw_screen) from [<c073e010>] (do_bind_con_driver+0x354/0x3c4) [ 25.562085] [<c073e010>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0) [ 25.562095] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8) [ 25.562107] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80) [ 25.562118] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68) [ 25.562129] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304) [ 25.562142] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c) [ 25.562156] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc) [ 25.562166] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634) [ 25.562179] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4) [ 25.562192] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174) [ 25.562206] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98) [ 25.562218] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c) [ 25.562229] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0) [ 25.562239] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4) [ 25.562250] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168) [ 25.562260] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c) [ 25.562271] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4) [ 25.562284] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564) [ 25.562297] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584) [ 25.562309] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150) [ 25.562319] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 25.562328] Exception stack(0xc4e09fb0 to 0xc4e09ff8) [ 25.562345] 9fa0: 00000000 00000000 00000000 00000000 [ 25.562370] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 25.562391] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 25.562399] ---[ end trace d4b922f6bb6a2606 ]--- [ 25.562431] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50] [ 25.562453] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval) [ 25.562467] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6) [ 25.562480] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (5) [ 25.562493] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2) [ 25.562507] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3) [ 25.562526] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval) [ 25.571673] [drm:drm_mode_object_get] OBJ ID: 50 (2) [ 25.571690] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval) [ 25.571705] [drm:drm_mode_object_get] OBJ ID: 51 (1) [ 25.571720] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval) [ 25.571732] [drm:drm_mode_object_get] OBJ ID: 53 (1) [ 25.571745] [drm:drm_atomic_check_only] checking (ptrval) [ 25.571767] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1) [ 25.571787] [drm:mdp5_crtc_atomic_check] crtc-0: check [ 25.571804] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1 [ 25.571817] [drm:drm_atomic_commit] committing (ptrval) [ 25.571836] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0) [ 26.223530] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 35.681745] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out [ 40.478585] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 40.531284] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 40.593999] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 40.916158] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 43.157049] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 45.172624] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) [ 45.921742] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:32:plane-0] flip_done timed out [ 45.921787] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920 [ 45.921801] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240 [ 45.921814] [drm:drm_atomic_helper_commit_planes] crtc-0: begin [ 45.921827] [drm:mdp5_plane_atomic_update] plane-0: update [ 45.921842] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920 [ 45.921854] [drm:mdp5_plane_mode_set] scale config = 0 [ 45.921879] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval) [ 45.921884] ------------[ cut here ]------------ [ 45.921898] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c:709 mdp5_crtc_atomic_flush+0x174/0x190 [ 45.921902] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod [ 45.921990] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303 [ 45.921998] Hardware name: Generic DT based system [ 45.922014] Workqueue: events drm_fb_helper_dirty_work [ 45.922034] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14) [ 45.922046] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c) [ 45.922061] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4) [ 45.922073] [<c0321660>] (__warn.part.3) from [<c03217d8>] (warn_slowpath_null+0x44/0x4c) [ 45.922086] [<c03217d8>] (warn_slowpath_null) from [<c07ad97c>] (mdp5_crtc_atomic_flush+0x174/0x190) [ 45.922099] [<c07ad97c>] (mdp5_crtc_atomic_flush) from [<c075f5e0>] (drm_atomic_helper_commit_planes+0x1fc/0x270) [ 45.922115] [<c075f5e0>] (drm_atomic_helper_commit_planes) from [<c07ddd04>] (msm_atomic_commit_tail+0x44/0x140) [ 45.922129] [<c07ddd04>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c) [ 45.922141] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128) [ 45.922156] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204) [ 45.922169] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164) [ 45.922182] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564) [ 45.922195] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584) [ 45.922208] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150) [ 45.922219] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 45.922228] Exception stack(0xde965fb0 to 0xde965ff8) [ 45.922246] 5fa0: 00000000 00000000 00000000 00000000 [ 45.922271] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 45.922291] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 45.922299] ---[ end trace d4b922f6bb6a2607 ]--- [ 45.922328] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000 [ 45.922343] [drm:crtc_flush] crtc-0: flush=00000840 [ 45.981760] msm fd900000.mdss: pp done time out, lm=0 [ 46.041730] ------------[ cut here ]------------ [ 46.041748] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 [ 46.041756] [CRTC:49:crtc-0] vblank wait timed out [ 46.041760] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod [ 46.041843] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303 [ 46.041851] Hardware name: Generic DT based system [ 46.041866] Workqueue: events drm_fb_helper_dirty_work [ 46.041884] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14) [ 46.041895] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c) [ 46.041907] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4) [ 46.041919] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88) [ 46.041933] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290) [ 46.041948] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40) [ 46.041964] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140) [ 46.041978] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c) [ 46.041990] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128) [ 46.042003] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204) [ 46.042014] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164) [ 46.042026] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564) [ 46.042039] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584) [ 46.042051] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150) [ 46.042061] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 46.042070] Exception stack(0xde965fb0 to 0xde965ff8) [ 46.042087] 5fa0: 00000000 00000000 00000000 00000000 [ 46.042112] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 46.042134] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 46.042141] ---[ end trace d4b922f6bb6a2608 ]--- [ 46.042171] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50] [ 46.042187] [drm:drm_mode_object_put.part.0] OBJ ID: 53 (2) [ 46.042204] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval) [ 46.042215] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2) [ 46.042230] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3) [ 46.042244] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval) [ 46.042273] [drm:drm_atomic_state_init] Allocated atomic state (ptrval) [ 46.042291] [drm:drm_mode_object_get] OBJ ID: 50 (2) [ 46.042306] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval) [ 46.042320] [drm:drm_mode_object_get] OBJ ID: 51 (1) [ 46.042335] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval) [ 46.042346] [drm:drm_mode_object_get] OBJ ID: 54 (1) [ 46.042359] [drm:drm_atomic_check_only] checking (ptrval) [ 46.042376] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1) [ 46.042395] [drm:mdp5_crtc_atomic_check] crtc-0: check [ 46.042411] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1 [ 46.042423] [drm:drm_atomic_commit] committing (ptrval) [ 46.042440] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0) [ 56.161749] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out [ 59.666659] [drm:dsi_host_irq] isr=0x2000700, id=0 [ 61.315067] [drm:mdp5_crtc_vblank_irq] crtc-0: send event: (ptrval) [ 61.315103] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0 [ 61.315117] [drm:vblank_disable_fn] disabling vblank on crtc 0 [ 61.315136] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0 [ 61.315147] [drm:msm_disable_vblank] dev=(ptrval), crtc=0 [ 61.315220] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920 [ 61.315234] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240 [ 61.315247] [drm:drm_atomic_helper_commit_planes] crtc-0: begin [ 61.315260] [drm:mdp5_plane_atomic_update] plane-0: update [ 61.315275] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920 [ 61.315286] [drm:mdp5_plane_mode_set] scale config = 0 [ 61.315311] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval) [ 61.315337] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000 [ 61.315351] [drm:crtc_flush] crtc-0: flush=00000840 [ 61.315369] [drm:msm_enable_vblank] dev=(ptrval), crtc=0 [ 61.315388] [drm:drm_vblank_enable] enabling vblank on crtc 0, ret: 0 [ 61.315406] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0 [ 61.318527] [drm:dsi_host_irq] isr=0x2000700, id=0 [ 61.371744] msm fd900000.mdss: pp done time out, lm=0 [ 61.431730] ------------[ cut here ]------------ [ 61.431747] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 [ 61.431754] [CRTC:49:crtc-0] vblank wait timed out [ 61.431758] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod [ 61.431843] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303 [ 61.431851] Hardware name: Generic DT based system [ 61.431866] Workqueue: events drm_fb_helper_dirty_work [ 61.431885] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14) [ 61.431896] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c) [ 61.431909] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4) [ 61.431922] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88) [ 61.431936] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290) [ 61.431952] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40) [ 61.431968] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140) [ 61.431981] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c) [ 61.431993] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128) [ 61.432006] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204) [ 61.432017] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164) [ 61.432031] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564) [ 61.432043] [<c033c4b0>] (process_one_work) from [<c033d384>] (worker_thread+0x2c0/0x584) [ 61.432055] [<c033d384>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150) [ 61.432066] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 61.432075] Exception stack(0xde965fb0 to 0xde965ff8) [ 61.432092] 5fa0: 00000000 00000000 00000000 00000000 [ 61.432117] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 61.432138] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 61.432147] ---[ end trace d4b922f6bb6a2609 ]--- [ 61.432176] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50] [ 61.432192] [drm:drm_mode_object_put.part.0] OBJ ID: 54 (2) [ 61.432207] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval) [ 61.432219] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2) [ 61.432232] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3) [ 61.432245] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval) [ 61.432373] msm fd900000.mdss: fb0: msmdrmfb frame buffer device [ 61.432405] [drm:drm_atomic_state_init] Allocated atomic state (ptrval) [ 61.432423] [drm:drm_mode_object_get] OBJ ID: 50 (2) [ 61.432438] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval) [ 61.432452] [drm:drm_mode_object_get] OBJ ID: 51 (1) [ 61.432470] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval) [ 61.432482] [drm:drm_mode_object_get] OBJ ID: 55 (1) [ 61.432496] [drm:drm_atomic_check_only] checking (ptrval) [ 61.432515] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1) [ 61.432534] [drm:mdp5_crtc_atomic_check] crtc-0: check [ 61.432552] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1 [ 61.432566] [drm:drm_atomic_commit] committing (ptrval) [ 61.432583] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0) [ 62.481750] [drm:drm_sysfs_hotplug_event] generating hotplug event
On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote: > Here is a patch series that adds initial display support for the LG > Nexus 5 (hammerhead) phone. It's not fully working so that's why some > of these patches are RFC until we can get it fully working. > > The phones boots into terminal mode, however there is a several second > (or more) delay when writing to tty1 compared to when the changes are > actually shown on the screen. The following errors are in dmesg: I tested to apply patches 2-6 and got the console up on the phone as well. I see the same timouts, and I also notice the update is slow in the display, as if the DSI panel was running in low power (LP) mode. Was booting this to do some other work, but happy to see the progress! Yours, Linus Walleij
On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote: > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote: > > > Here is a patch series that adds initial display support for the LG > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some > > of these patches are RFC until we can get it fully working. > > > > The phones boots into terminal mode, however there is a several second > > (or more) delay when writing to tty1 compared to when the changes are > > actually shown on the screen. The following errors are in dmesg: > > I tested to apply patches 2-6 and got the console up on the phone as well. > I see the same timouts, and I also notice the update is slow in the > display, as if the DSI panel was running in low power (LP) mode. > > Was booting this to do some other work, but happy to see the progress! Thanks! I've had three people email me off list regarding the display working on 4.17 before the msm kms/drm driver was converted to the DRM atomic API so this email is to get some more information out publicly. I pushed up a branch to my github with 15 patches applied against 4.17 that has a working display: https://github.com/masneyb/linux/commits/display-works-4.17 It's in low speed mode but its usable. The first 10 patches are in mainline now and the last 5 are in essence this patch series with the exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'. There's a slightly different version of that patch in mainline now. I'm planning to work on the msm8974 interconnect support once some of the outstanding interconnect patches for the msm kms/drm driver arrive in mainline. I'd really like to understand why the display works on 4.17 with those patches though. I assume that it's related to the vblank events not working properly? Let me preface this with I'm a total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't looking for these events in the atomic commits before the migration? See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic helper commit"), specifically the drm_atomic_helper_wait_for_vblanks() call that was added. Brian
On Tue, May 28, 2019 at 7:17 PM Brian Masney <masneyb@onstation.org> wrote: > > On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote: > > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote: > > > > > Here is a patch series that adds initial display support for the LG > > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some > > > of these patches are RFC until we can get it fully working. > > > > > > The phones boots into terminal mode, however there is a several second > > > (or more) delay when writing to tty1 compared to when the changes are > > > actually shown on the screen. The following errors are in dmesg: > > > > I tested to apply patches 2-6 and got the console up on the phone as well. > > I see the same timouts, and I also notice the update is slow in the > > display, as if the DSI panel was running in low power (LP) mode. > > > > Was booting this to do some other work, but happy to see the progress! > > Thanks! > > I've had three people email me off list regarding the display working on > 4.17 before the msm kms/drm driver was converted to the DRM atomic API so > this email is to get some more information out publicly. > > I pushed up a branch to my github with 15 patches applied against 4.17 > that has a working display: > > https://github.com/masneyb/linux/commits/display-works-4.17 > > It's in low speed mode but its usable. The first 10 patches are in > mainline now and the last 5 are in essence this patch series with the > exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'. > There's a slightly different version of that patch in mainline now. > > I'm planning to work on the msm8974 interconnect support once some of > the outstanding interconnect patches for the msm kms/drm driver arrive > in mainline. I'd really like to understand why the display works on > 4.17 with those patches though. I assume that it's related to the > vblank events not working properly? Let me preface this with I'm a > total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't > looking for these events in the atomic commits before the migration? > See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic > helper commit"), specifically the drm_atomic_helper_wait_for_vblanks() > call that was added. Do you know if the nexus 5 has a video or command mode panel? There is some glitchyness with vblanks and command mode panels.
On Tue, May 28, 2019 at 07:32:14PM -0600, Jeffrey Hugo wrote: > On Tue, May 28, 2019 at 7:17 PM Brian Masney <masneyb@onstation.org> wrote: > > > > On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote: > > > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote: > > > > > > > Here is a patch series that adds initial display support for the LG > > > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some > > > > of these patches are RFC until we can get it fully working. > > > > > > > > The phones boots into terminal mode, however there is a several second > > > > (or more) delay when writing to tty1 compared to when the changes are > > > > actually shown on the screen. The following errors are in dmesg: > > > > > > I tested to apply patches 2-6 and got the console up on the phone as well. > > > I see the same timouts, and I also notice the update is slow in the > > > display, as if the DSI panel was running in low power (LP) mode. > > > > > > Was booting this to do some other work, but happy to see the progress! > > > > Thanks! > > > > I've had three people email me off list regarding the display working on > > 4.17 before the msm kms/drm driver was converted to the DRM atomic API so > > this email is to get some more information out publicly. > > > > I pushed up a branch to my github with 15 patches applied against 4.17 > > that has a working display: > > > > https://github.com/masneyb/linux/commits/display-works-4.17 > > > > It's in low speed mode but its usable. The first 10 patches are in > > mainline now and the last 5 are in essence this patch series with the > > exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'. > > There's a slightly different version of that patch in mainline now. > > > > I'm planning to work on the msm8974 interconnect support once some of > > the outstanding interconnect patches for the msm kms/drm driver arrive > > in mainline. I'd really like to understand why the display works on > > 4.17 with those patches though. I assume that it's related to the > > vblank events not working properly? Let me preface this with I'm a > > total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't > > looking for these events in the atomic commits before the migration? > > See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic > > helper commit"), specifically the drm_atomic_helper_wait_for_vblanks() > > call that was added. > > Do you know if the nexus 5 has a video or command mode panel? There > is some glitchyness with vblanks and command mode panels. Its in command mode. I know this because I see two 'pp done time out' messages, even on 4.17. Based on my understanding, the ping pong code is only applicable for command mode panels. Brian
On Tue, May 28, 2019 at 7:37 PM Brian Masney <masneyb@onstation.org> wrote: > > On Tue, May 28, 2019 at 07:32:14PM -0600, Jeffrey Hugo wrote: > > On Tue, May 28, 2019 at 7:17 PM Brian Masney <masneyb@onstation.org> wrote: > > > > > > On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote: > > > > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote: > > > > > > > > > Here is a patch series that adds initial display support for the LG > > > > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some > > > > > of these patches are RFC until we can get it fully working. > > > > > > > > > > The phones boots into terminal mode, however there is a several second > > > > > (or more) delay when writing to tty1 compared to when the changes are > > > > > actually shown on the screen. The following errors are in dmesg: > > > > > > > > I tested to apply patches 2-6 and got the console up on the phone as well. > > > > I see the same timouts, and I also notice the update is slow in the > > > > display, as if the DSI panel was running in low power (LP) mode. > > > > > > > > Was booting this to do some other work, but happy to see the progress! > > > > > > Thanks! > > > > > > I've had three people email me off list regarding the display working on > > > 4.17 before the msm kms/drm driver was converted to the DRM atomic API so > > > this email is to get some more information out publicly. > > > > > > I pushed up a branch to my github with 15 patches applied against 4.17 > > > that has a working display: > > > > > > https://github.com/masneyb/linux/commits/display-works-4.17 > > > > > > It's in low speed mode but its usable. The first 10 patches are in > > > mainline now and the last 5 are in essence this patch series with the > > > exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'. > > > There's a slightly different version of that patch in mainline now. > > > > > > I'm planning to work on the msm8974 interconnect support once some of > > > the outstanding interconnect patches for the msm kms/drm driver arrive > > > in mainline. I'd really like to understand why the display works on > > > 4.17 with those patches though. I assume that it's related to the > > > vblank events not working properly? Let me preface this with I'm a > > > total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't > > > looking for these events in the atomic commits before the migration? > > > See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic > > > helper commit"), specifically the drm_atomic_helper_wait_for_vblanks() > > > call that was added. > > > > Do you know if the nexus 5 has a video or command mode panel? There > > is some glitchyness with vblanks and command mode panels. > > Its in command mode. I know this because I see two 'pp done time out' > messages, even on 4.17. Based on my understanding, the ping pong code is > only applicable for command mode panels. Actually, the ping pong element exists in both modes, but 'pp done time out' is a good indicator that it is command mode. Are you also seeing vblank timeouts? Do you have busybox? Can you run - sudo busybox devmem 0xFD900614 sudo busybox devmem 0xFD900714 sudo busybox devmem 0xFD900814 sudo busybox devmem 0xFD900914 sudo busybox devmem 0xFD900A14
On Tue, May 28, 2019 at 6:17 PM Brian Masney <masneyb@onstation.org> wrote: > > On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote: > > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote: > > > > > Here is a patch series that adds initial display support for the LG > > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some > > > of these patches are RFC until we can get it fully working. > > > > > > The phones boots into terminal mode, however there is a several second > > > (or more) delay when writing to tty1 compared to when the changes are > > > actually shown on the screen. The following errors are in dmesg: > > > > I tested to apply patches 2-6 and got the console up on the phone as well. > > I see the same timouts, and I also notice the update is slow in the > > display, as if the DSI panel was running in low power (LP) mode. > > > > Was booting this to do some other work, but happy to see the progress! > > Thanks! > > I've had three people email me off list regarding the display working on > 4.17 before the msm kms/drm driver was converted to the DRM atomic API so > this email is to get some more information out publicly. > > I pushed up a branch to my github with 15 patches applied against 4.17 > that has a working display: > > https://github.com/masneyb/linux/commits/display-works-4.17 > > It's in low speed mode but its usable. The first 10 patches are in > mainline now and the last 5 are in essence this patch series with the > exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'. > There's a slightly different version of that patch in mainline now. > > I'm planning to work on the msm8974 interconnect support once some of > the outstanding interconnect patches for the msm kms/drm driver arrive > in mainline. I'd really like to understand why the display works on > 4.17 with those patches though. I assume that it's related to the > vblank events not working properly? Let me preface this with I'm a > total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't > looking for these events in the atomic commits before the migration? > See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic > helper commit"), specifically the drm_atomic_helper_wait_for_vblanks() > call that was added. interconnect probably good to get going anyways (and I need to find some time to respin those mdp5/dpu patches) but I guess not related to what you see (ie. I'd expect interconnect issue would trigger underflow irq's).. I'm not entirely sure why atomic would break things but cmd mode panels aren't especially well tested. I can't find it now but there was a thread (or IRC discussion?) that intf2vblank() should be returning MDP5_IRQ_PING_PONG_<n>_DONE instead of MDP5_IRQ_PING_PONG_<n>_RD_PTR, which seems likely and possibly related to vblank timing issues.. BR, -R > > Brian
On Tue, May 28, 2019 at 8:15 PM Rob Clark <robdclark@gmail.com> wrote: > > On Tue, May 28, 2019 at 6:17 PM Brian Masney <masneyb@onstation.org> wrote: > > > > On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote: > > > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote: > > > > > > > Here is a patch series that adds initial display support for the LG > > > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some > > > > of these patches are RFC until we can get it fully working. > > > > > > > > The phones boots into terminal mode, however there is a several second > > > > (or more) delay when writing to tty1 compared to when the changes are > > > > actually shown on the screen. The following errors are in dmesg: > > > > > > I tested to apply patches 2-6 and got the console up on the phone as well. > > > I see the same timouts, and I also notice the update is slow in the > > > display, as if the DSI panel was running in low power (LP) mode. > > > > > > Was booting this to do some other work, but happy to see the progress! > > > > Thanks! > > > > I've had three people email me off list regarding the display working on > > 4.17 before the msm kms/drm driver was converted to the DRM atomic API so > > this email is to get some more information out publicly. > > > > I pushed up a branch to my github with 15 patches applied against 4.17 > > that has a working display: > > > > https://github.com/masneyb/linux/commits/display-works-4.17 > > > > It's in low speed mode but its usable. The first 10 patches are in > > mainline now and the last 5 are in essence this patch series with the > > exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'. > > There's a slightly different version of that patch in mainline now. > > > > I'm planning to work on the msm8974 interconnect support once some of > > the outstanding interconnect patches for the msm kms/drm driver arrive > > in mainline. I'd really like to understand why the display works on > > 4.17 with those patches though. I assume that it's related to the > > vblank events not working properly? Let me preface this with I'm a > > total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't > > looking for these events in the atomic commits before the migration? > > See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic > > helper commit"), specifically the drm_atomic_helper_wait_for_vblanks() > > call that was added. > > interconnect probably good to get going anyways (and I need to find > some time to respin those mdp5/dpu patches) but I guess not related to > what you see (ie. I'd expect interconnect issue would trigger > underflow irq's).. > > I'm not entirely sure why atomic would break things but cmd mode > panels aren't especially well tested. I can't find it now but there > was a thread (or IRC discussion?) that intf2vblank() should be > returning MDP5_IRQ_PING_PONG_<n>_DONE instead of > MDP5_IRQ_PING_PONG_<n>_RD_PTR, which seems likely and possibly related > to vblank timing issues.. That was an irc discussion, and I've changed my mind on that. My big issue ended up being that autorefresh was enabled (which basically turns the command panel into a pseudo video mode panel), which appears incompatible with using the start kick. If FW is configuring things in autorefresh mode, the driver likely doesn't know, and will make a mess of things by using the start kick. Disabling autorefresh would make the driver work as is, but fbcon wouldn't work well (you'd need to do a start kick per frame, which doesn't seem to happen). Removing the start kick and using the autorefresh feature seemed better in my testing, but I haven't cleaned up my code tree to send something up. However, lets see how the hardware is actually configured in Brian's case.
On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote: > > > Do you know if the nexus 5 has a video or command mode panel? There > > > is some glitchyness with vblanks and command mode panels. > > > > Its in command mode. I know this because I see two 'pp done time out' > > messages, even on 4.17. Based on my understanding, the ping pong code is > > only applicable for command mode panels. > > Actually, the ping pong element exists in both modes, but 'pp done > time out' is a good indicator that it is command mode. > > Are you also seeing vblank timeouts? Yes, here's a snippet of the first one. [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out [ 2.556023] Modules linked in: [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426 [ 2.556038] Hardware name: Generic DT based system [ 2.556056] Workqueue: events deferred_probe_work_func ... > Do you have busybox? > > Can you run - > sudo busybox devmem 0xFD900614 > sudo busybox devmem 0xFD900714 > sudo busybox devmem 0xFD900814 > sudo busybox devmem 0xFD900914 > sudo busybox devmem 0xFD900A14 # busybox devmem 0xFD900614 0x00020020 # busybox devmem 0xFD900714 0x00000000 # busybox devmem 0xFD900814 0x00000000 # busybox devmem 0xFD900914 0x00000000 # busybox devmem 0xFD900A14 0x00000000 I get the same values with the mainline kernel and 4.17. Brian
On Wed, May 29, 2019 at 3:17 AM Brian Masney <masneyb@onstation.org> wrote: > It's in low speed mode but its usable. How low speed is that? > I assume that it's related to the > vblank events not working properly? They are only waiting for 50 ms before timing out, I raised it to 100ms in the -next kernel. I'm still suspicious about this even though I think you said this was not the problem. For a command mode panel in LP mode it will nevertheless be more than 100ms for sure, the update is visible to the naked eye. Raise it to 10000 ms or something and see what happens. drivers/gpu/drm/drm_atomic_helper.c: msecs_to_jiffies(50) Yours, Linus Walleij
On Wed, May 29, 2019 at 08:23:17AM +0200, Linus Walleij wrote: > On Wed, May 29, 2019 at 3:17 AM Brian Masney <masneyb@onstation.org> wrote: > > > It's in low speed mode but its usable. > > How low speed is that? I don't have a number but my test with 4.17 is to run 'cat /etc/passwd > /dev/tty1' over a serial cable. The first 2-3 calls will fill up the screen and the file contents appear to show up on the screen immediately to the human eye. The next time that I run it requires scrolling the entire console and there is a small fraction of a second where I see the entire framebuffer contents scroll up. I don't have a graphics background, but I believe that this is the tearing effect that I'm seeing based on what I've read. I believe that disp-te-gpios can be used to mitigate this tearing effect. I have a few questions about this later once we get the basic display working. > > I assume that it's related to the > > vblank events not working properly? > > They are only waiting for 50 ms before timing out, I raised it > to 100ms in the -next kernel. I'm still suspicious about this > even though I think you said this was not the problem. > > For a command mode panel in LP mode it will nevertheless > be more than 100ms for sure, the update is visible to the > naked eye. > > Raise it to 10000 ms or something and see what happens. > drivers/gpu/drm/drm_atomic_helper.c: > msecs_to_jiffies(50) I previously raised those timeouts as high as 5 seconds and it still has the same issue. Writing to /dev/tty1 can take anywhere between a few seconds to 30 seconds or more. Brian
On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote: > On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote: > > > > On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote: > > > > > Do you know if the nexus 5 has a video or command mode panel? There > > > > > is some glitchyness with vblanks and command mode panels. > > > > > > > > Its in command mode. I know this because I see two 'pp done time out' > > > > messages, even on 4.17. Based on my understanding, the ping pong code is > > > > only applicable for command mode panels. > > > > > > Actually, the ping pong element exists in both modes, but 'pp done > > > time out' is a good indicator that it is command mode. > > > > > > Are you also seeing vblank timeouts? > > > > Yes, here's a snippet of the first one. > > > > [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 > > [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out > > [ 2.556023] Modules linked in: > > [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426 > > [ 2.556038] Hardware name: Generic DT based system > > [ 2.556056] Workqueue: events deferred_probe_work_func > > ... > > > > > Do you have busybox? > > > > > > Can you run - > > > sudo busybox devmem 0xFD900614 > > > sudo busybox devmem 0xFD900714 > > > sudo busybox devmem 0xFD900814 > > > sudo busybox devmem 0xFD900914 > > > sudo busybox devmem 0xFD900A14 > > > > # busybox devmem 0xFD900614 > > 0x00020020 > > Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1. > > Next one please: > > busybox devmem 0xFD912D30 It's 0x00000000 on mainline and 4.17. I used the following script to dump the entire mdp5 memory region and attached the dump from 4.17 and 5.2rc1. POS="0XFD900100" while [ "${POS}" != "0XFD925000" ] ; do echo -n "${POS} = " busybox devmem "${POS}" POS=$(printf '%#X' "$((${POS} + 4))") done Brian
On Wed, May 29, 2019 at 4:28 AM Brian Masney <masneyb@onstation.org> wrote: > > On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote: > > On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote: > > > > > > On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote: > > > > > > Do you know if the nexus 5 has a video or command mode panel? There > > > > > > is some glitchyness with vblanks and command mode panels. > > > > > > > > > > Its in command mode. I know this because I see two 'pp done time out' > > > > > messages, even on 4.17. Based on my understanding, the ping pong code is > > > > > only applicable for command mode panels. > > > > > > > > Actually, the ping pong element exists in both modes, but 'pp done > > > > time out' is a good indicator that it is command mode. > > > > > > > > Are you also seeing vblank timeouts? > > > > > > Yes, here's a snippet of the first one. > > > > > > [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 > > > [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out > > > [ 2.556023] Modules linked in: > > > [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426 > > > [ 2.556038] Hardware name: Generic DT based system > > > [ 2.556056] Workqueue: events deferred_probe_work_func > > > ... > > > > > > > Do you have busybox? > > > > > > > > Can you run - > > > > sudo busybox devmem 0xFD900614 > > > > sudo busybox devmem 0xFD900714 > > > > sudo busybox devmem 0xFD900814 > > > > sudo busybox devmem 0xFD900914 > > > > sudo busybox devmem 0xFD900A14 > > > > > > # busybox devmem 0xFD900614 > > > 0x00020020 > > > > Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1. > > > > Next one please: > > > > busybox devmem 0xFD912D30 > > It's 0x00000000 on mainline and 4.17. I used the following script to > dump the entire mdp5 memory region and attached the dump from 4.17 and > 5.2rc1. > ok, 0 means autorefresh is not on. Which is fine. My next guess would be the vblank code checking the hardware vblank counter, which doesn't exist. In video mode, there is a frame counter which increments, which can be used as the vblank counter. Unfortunately, that hardware isn't active in command mode, and there isn't an equivalent. So, the vblank code is going to read the register, and look for an update, which will never happen, thus it will timeout. There is a backup path which uses timestamps (no hardware), which you can activate with a quick hack - make max_vblank_count = 0 at the following line https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c#L753
On Wed, May 29, 2019 at 08:41:31AM -0600, Jeffrey Hugo wrote: > On Wed, May 29, 2019 at 4:28 AM Brian Masney <masneyb@onstation.org> wrote: > > > > On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote: > > > On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote: > > > > > > > > On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote: > > > > > > > Do you know if the nexus 5 has a video or command mode panel? There > > > > > > > is some glitchyness with vblanks and command mode panels. > > > > > > > > > > > > Its in command mode. I know this because I see two 'pp done time out' > > > > > > messages, even on 4.17. Based on my understanding, the ping pong code is > > > > > > only applicable for command mode panels. > > > > > > > > > > Actually, the ping pong element exists in both modes, but 'pp done > > > > > time out' is a good indicator that it is command mode. > > > > > > > > > > Are you also seeing vblank timeouts? > > > > > > > > Yes, here's a snippet of the first one. > > > > > > > > [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 > > > > [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out > > > > [ 2.556023] Modules linked in: > > > > [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426 > > > > [ 2.556038] Hardware name: Generic DT based system > > > > [ 2.556056] Workqueue: events deferred_probe_work_func > > > > ... > > > > > > > > > Do you have busybox? > > > > > > > > > > Can you run - > > > > > sudo busybox devmem 0xFD900614 > > > > > sudo busybox devmem 0xFD900714 > > > > > sudo busybox devmem 0xFD900814 > > > > > sudo busybox devmem 0xFD900914 > > > > > sudo busybox devmem 0xFD900A14 > > > > > > > > # busybox devmem 0xFD900614 > > > > 0x00020020 > > > > > > Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1. > > > > > > Next one please: > > > > > > busybox devmem 0xFD912D30 > > > > It's 0x00000000 on mainline and 4.17. I used the following script to > > dump the entire mdp5 memory region and attached the dump from 4.17 and > > 5.2rc1. > > > > ok, 0 means autorefresh is not on. Which is fine. My next guess > would be the vblank code checking the hardware vblank counter, which > doesn't exist. > In video mode, there is a frame counter which increments, which can be > used as the vblank counter. Unfortunately, that hardware isn't active > in command mode, and there isn't an equivalent. > > So, the vblank code is going to read the register, and look for an > update, which will never happen, thus it will timeout. There is a > backup path which uses timestamps (no hardware), which you can > activate with a quick hack - make max_vblank_count = 0 at the > following line > https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c#L753 That fixed the issue! I previously observed that mdp5_get_vblank_counter, specifically mdp5_encoder_get_framecount, would always return 0. What's the best way to fix this in mainline? Set that to zero if any of the interface modes is MDP5_INTF_DSI_MODE_COMMAND? Brian
On 5/29/2019 1:30 PM, Brian Masney wrote: > On Wed, May 29, 2019 at 08:41:31AM -0600, Jeffrey Hugo wrote: >> On Wed, May 29, 2019 at 4:28 AM Brian Masney <masneyb@onstation.org> wrote: >>> >>> On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote: >>>> On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote: >>>>> >>>>> On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote: >>>>>>>> Do you know if the nexus 5 has a video or command mode panel? There >>>>>>>> is some glitchyness with vblanks and command mode panels. >>>>>>> >>>>>>> Its in command mode. I know this because I see two 'pp done time out' >>>>>>> messages, even on 4.17. Based on my understanding, the ping pong code is >>>>>>> only applicable for command mode panels. >>>>>> >>>>>> Actually, the ping pong element exists in both modes, but 'pp done >>>>>> time out' is a good indicator that it is command mode. >>>>>> >>>>>> Are you also seeing vblank timeouts? >>>>> >>>>> Yes, here's a snippet of the first one. >>>>> >>>>> [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 >>>>> [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out >>>>> [ 2.556023] Modules linked in: >>>>> [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426 >>>>> [ 2.556038] Hardware name: Generic DT based system >>>>> [ 2.556056] Workqueue: events deferred_probe_work_func >>>>> ... >>>>> >>>>>> Do you have busybox? >>>>>> >>>>>> Can you run - >>>>>> sudo busybox devmem 0xFD900614 >>>>>> sudo busybox devmem 0xFD900714 >>>>>> sudo busybox devmem 0xFD900814 >>>>>> sudo busybox devmem 0xFD900914 >>>>>> sudo busybox devmem 0xFD900A14 >>>>> >>>>> # busybox devmem 0xFD900614 >>>>> 0x00020020 >>>> >>>> Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1. >>>> >>>> Next one please: >>>> >>>> busybox devmem 0xFD912D30 >>> >>> It's 0x00000000 on mainline and 4.17. I used the following script to >>> dump the entire mdp5 memory region and attached the dump from 4.17 and >>> 5.2rc1. >>> >> >> ok, 0 means autorefresh is not on. Which is fine. My next guess >> would be the vblank code checking the hardware vblank counter, which >> doesn't exist. >> In video mode, there is a frame counter which increments, which can be >> used as the vblank counter. Unfortunately, that hardware isn't active >> in command mode, and there isn't an equivalent. >> >> So, the vblank code is going to read the register, and look for an >> update, which will never happen, thus it will timeout. There is a >> backup path which uses timestamps (no hardware), which you can >> activate with a quick hack - make max_vblank_count = 0 at the >> following line >> https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c#L753 > > That fixed the issue! Awesome. I'm glad it was something simple. > > I previously observed that mdp5_get_vblank_counter, specifically > mdp5_encoder_get_framecount, would always return 0. > > What's the best way to fix this in mainline? Set that to zero if any > of the interface modes is MDP5_INTF_DSI_MODE_COMMAND? > Short version, yes. Long version: I still have that hack in my tree and haven't come back to formulating a proper fix yet. Feel free to run with it. Thinking about it briefly, we could do two things. We could fake a hardware counter by just increment an int every time the vblank irq is processed, but that seems clunky. Otherwise, we could force a fallback onto the timestamp solution, which seems less invasive. In theory, we could service multiple displays, with different properties (ie a combination of command and video mode). The hack then, is not good, because it would break video mode (at-least we wouldn't be using the register when we could). It would be great if the use of the hardware register could be done per display. Luckily, it looks like someone just made that possible - https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/gpu/drm/drm_vblank.c?h=v5.2-rc2&id=ed20151a7699bb2c77eba3610199789a126940c4
On Wed, May 29, 2019 at 01:58:16PM -0600, Jeffrey Hugo wrote: > On 5/29/2019 1:30 PM, Brian Masney wrote: > > On Wed, May 29, 2019 at 08:41:31AM -0600, Jeffrey Hugo wrote: > > > On Wed, May 29, 2019 at 4:28 AM Brian Masney <masneyb@onstation.org> wrote: > > > > > > > > On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote: > > > > > On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote: > > > > > > > > > > > > On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote: > > > > > > > > > Do you know if the nexus 5 has a video or command mode panel? There > > > > > > > > > is some glitchyness with vblanks and command mode panels. > > > > > > > > > > > > > > > > Its in command mode. I know this because I see two 'pp done time out' > > > > > > > > messages, even on 4.17. Based on my understanding, the ping pong code is > > > > > > > > only applicable for command mode panels. > > > > > > > > > > > > > > Actually, the ping pong element exists in both modes, but 'pp done > > > > > > > time out' is a good indicator that it is command mode. > > > > > > > > > > > > > > Are you also seeing vblank timeouts? > > > > > > > > > > > > Yes, here's a snippet of the first one. > > > > > > > > > > > > [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 > > > > > > [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out > > > > > > [ 2.556023] Modules linked in: > > > > > > [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426 > > > > > > [ 2.556038] Hardware name: Generic DT based system > > > > > > [ 2.556056] Workqueue: events deferred_probe_work_func > > > > > > ... > > > > > > > > > > > > > Do you have busybox? > > > > > > > > > > > > > > Can you run - > > > > > > > sudo busybox devmem 0xFD900614 > > > > > > > sudo busybox devmem 0xFD900714 > > > > > > > sudo busybox devmem 0xFD900814 > > > > > > > sudo busybox devmem 0xFD900914 > > > > > > > sudo busybox devmem 0xFD900A14 > > > > > > > > > > > > # busybox devmem 0xFD900614 > > > > > > 0x00020020 > > > > > > > > > > Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1. > > > > > > > > > > Next one please: > > > > > > > > > > busybox devmem 0xFD912D30 > > > > > > > > It's 0x00000000 on mainline and 4.17. I used the following script to > > > > dump the entire mdp5 memory region and attached the dump from 4.17 and > > > > 5.2rc1. > > > > > > > > > > ok, 0 means autorefresh is not on. Which is fine. My next guess > > > would be the vblank code checking the hardware vblank counter, which > > > doesn't exist. > > > In video mode, there is a frame counter which increments, which can be > > > used as the vblank counter. Unfortunately, that hardware isn't active > > > in command mode, and there isn't an equivalent. > > > > > > So, the vblank code is going to read the register, and look for an > > > update, which will never happen, thus it will timeout. There is a > > > backup path which uses timestamps (no hardware), which you can > > > activate with a quick hack - make max_vblank_count = 0 at the > > > following line > > > https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c#L753 > > > > That fixed the issue! > > Awesome. I'm glad it was something simple. > > > > > I previously observed that mdp5_get_vblank_counter, specifically > > mdp5_encoder_get_framecount, would always return 0. > > > > What's the best way to fix this in mainline? Set that to zero if any > > of the interface modes is MDP5_INTF_DSI_MODE_COMMAND? > > > > Short version, yes. Long version: > > I still have that hack in my tree and haven't come back to formulating > a proper fix yet. Feel free to run with it. > > Thinking about it briefly, we could do two things. We could fake a > hardware counter by just increment an int every time the vblank irq is > processed, but that seems clunky. Otherwise, we could force a > fallback onto the timestamp solution, which seems less invasive. > > In theory, we could service multiple displays, with different > properties (ie a combination of command and video mode). The hack > then, is not good, because it would break video mode (at-least we > wouldn't be using the register when we could). It would be great if > the use of the hardware register could be done per display. > > Luckily, it looks like someone just made that possible - > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/gpu/drm/drm_vblank.c?h=v5.2-rc2&id=ed20151a7699bb2c77eba3610199789a126940c4 I'll work on this for the msm driver. Thanks for the info! Brian
Here is a patch series that adds initial display support for the LG Nexus 5 (hammerhead) phone. It's not fully working so that's why some of these patches are RFC until we can get it fully working. The phones boots into terminal mode, however there is a several second (or more) delay when writing to tty1 compared to when the changes are actually shown on the screen. The following errors are in dmesg: [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:32:plane-0] flip_done timed out WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1430 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290 [CRTC:49:crtc-0] vblank wait timed out Modules linked in: CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.1.0-rc6-next-20190426-00006-g35c0d32a96e1-dirty #191 Hardware name: Generic DT based system Workqueue: events deferred_probe_work_func [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14) [<c030d5ac>] (show_stack) from [<c0ac134c>] (dump_stack+0x78/0x8c) [<c0ac134c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4) [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88) [<c03216e0>] (warn_slowpath_fmt) from [<c0761a0c>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290) [<c0761a0c>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0a98>] (mdp5_complete_commit+0x14/0x40) [<c07b0a98>] (mdp5_complete_commit) from [<c07ddb80>] (msm_atomic_commit_tail+0xa8/0x140) [<c07ddb80>] (msm_atomic_commit_tail) from [<c0763304>] (commit_tail+0x40/0x6c) [<c07633f4>] (drm_atomic_helper_commit) from [<c07667f0>] (restore_fbdev_mode_atomic+0x168/0x1d4) .... I can get the text console to work with a 4.17 kernel with this patch https://patchwork.kernel.org/patch/10321845/ plus about a dozen or more other patches that have been mainlined since that release. I'm new to the DRM subsystem and continuing to dig into the issue, however I'd appreciate any suggestions. I suspect the issue lies somewhere in the second patch in this series. Changes since v1: - Shortened problem description above. I'll reply to this email and send a full dmesg with the boot log with debugging turned on. - Dropped patch 'fix null pointer dereference in msm_atomic_prepare_fb()' - New patch: Remove resv fields from msm_gem_object struct that was incorrectly being referenced by the prepare_fb callbacks. - Add drm_plane_enable_fb_damage_clips() to plane init for mdp4, mdp5, and dpu1. - Add Linus Walleij's reviewed-by to patches 3-6 Brian Masney (6): drm: msm: remove resv fields from msm_gem_object struct drm: msm: add dirty framebuffer helper ARM: qcom_defconfig: add display-related options ARM: dts: msm8974: add display support ARM: dts: qcom: msm8974-hammerhead: add support for backlight ARM: dts: qcom: msm8974-hammerhead: add support for display .../qcom-msm8974-lge-nexus5-hammerhead.dts | 79 +++++++++++ arch/arm/boot/dts/qcom-msm8974.dtsi | 132 ++++++++++++++++++ arch/arm/configs/qcom_defconfig | 5 + drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 7 +- drivers/gpu/drm/msm/disp/mdp4/mdp4_plane.c | 3 + drivers/gpu/drm/msm/disp/mdp5/mdp5_plane.c | 3 + drivers/gpu/drm/msm/msm_atomic.c | 4 +- drivers/gpu/drm/msm/msm_fb.c | 2 + drivers/gpu/drm/msm/msm_gem.c | 3 - drivers/gpu/drm/msm/msm_gem.h | 4 - 10 files changed, 229 insertions(+), 13 deletions(-)