@@ -8,6 +8,9 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8994-angler-rev-101.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
new file mode 100644
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Cheza board device tree source
+ *
+ * Copyright 2018 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sdm845-cheza.dtsi"
+
+/ {
+ model = "Google Cheza (rev1)";
+ compatible = "google,cheza-rev1", "google,cheza", "qcom,sdm845";
+
+ /*
+ * FIXED REGULATORS (not in sdm845-cheza.dtsi) - parents above children
+ */
+
+ /*
+ * NOTE: Technically pp3500_a is not the exact same signal as
+ * pp3500_a_vbob (there's a load switch between them and the EC can
+ * control pp3500_a via "en_pp3300_a"), but from the AP's point of
+ * view they are the same.
+ */
+ pp3500_a:
+ pp3500_a_vbob: pp3500-a-vbob-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_bob";
+
+ /*
+ * Comes on automatically when pp5000_ldo comes on, which
+ * comes on automatically when ppvar_sys comes on
+ */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3500000>;
+ regulator-max-microvolt = <3500000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp3300_dx_edp: pp3300-dx-edp-regulator {
+ /* Yes, it's really 3.5 despite the name of the signal */
+ regulator-min-microvolt = <3500000>;
+ regulator-max-microvolt = <3500000>;
+
+ vin-supply = <&pp3500_a>;
+ };
+};
+
+/* FIXED REGULATOR OVERRIDES (modifications to sdm845-cheza.dtsi) */
+
+/*
+ * L19 and L28 technically go to 3.3V, but most boards have old AOP firmware
+ * that limits them to 3.0, and trying to run at 3.3V with that old firmware
+ * prevents the system from booting.
+ */
+&src_pp3000_l19a {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+};
+
+&src_pp3300_l22a {
+ /delete-property/regulator-boot-on;
+ /delete-property/regulator-always-on;
+};
+
+&src_pp3300_l28a {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+};
+
+&src_vreg_bob {
+ regulator-min-microvolt = <3500000>;
+ regulator-max-microvolt = <3500000>;
+ vin-supply = <&pp3500_a_vbob>;
+};
+
+/*
+ * NON-REGULATOR OVERRIDES
+ * (modifications to sdm845-cheza.dtsi) - alphabetized by dtsi label
+ */
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+ gpio-line-names = "AP_SPI_FP_MISO",
+ "AP_SPI_FP_MOSI",
+ "AP_SPI_FP_CLK",
+ "AP_SPI_FP_CS_L",
+ "UART_AP_TX_DBG_RX",
+ "UART_DBG_TX_AP_RX",
+ "",
+ "FP_RST_L",
+ "FCAM_EN",
+ "",
+ "EDP_BRIJ_IRQ",
+ "EC_IN_RW_ODL",
+ "",
+ "RCAM_MCLK",
+ "FCAM_MCLK",
+ "",
+ "RCAM_EN",
+ "CCI0_SDA",
+ "CCI0_SCL",
+ "CCI1_SDA",
+ "CCI1_SCL",
+ "FCAM_RST_L",
+ "",
+ "PEN_RST_L",
+ "PEN_IRQ_L",
+ "",
+ "RCAM_VSYNC",
+ "ESIM_MISO",
+ "ESIM_MOSI",
+ "ESIM_CLK",
+ "ESIM_CS_L",
+ "AP_PEN_1V8_SDA",
+ "AP_PEN_1V8_SCL",
+ "AP_TS_I2C_SDA",
+ "AP_TS_I2C_SCL",
+ "RCAM_RST_L",
+ "",
+ "AP_EDP_BKLTEN",
+ "AP_BRD_ID1",
+ "BOOT_CONFIG_4",
+ "AMP_IRQ_L",
+ "EDP_BRIJ_I2C_SDA",
+ "EDP_BRIJ_I2C_SCL",
+ "EN_PP3300_DX_EDP",
+ "SD_CD_ODL",
+ "BT_UART_RTS",
+ "BT_UART_CTS",
+ "BT_UART_RXD",
+ "BT_UART_TXD",
+ "AMP_I2C_SDA",
+ "AMP_I2C_SCL",
+ "AP_BRD_ID3",
+ "",
+ "AP_EC_SPI_CLK",
+ "AP_EC_SPI_CS_L",
+ "AP_EC_SPI_MISO",
+ "AP_EC_SPI_MOSI",
+ "FORCED_USB_BOOT",
+ "AMP_BCLK",
+ "AMP_LRCLK",
+ "AMP_DOUT",
+ "AMP_DIN",
+ "AP_BRD_ID2",
+ "PEN_PDCT_L",
+ "HP_MCLK",
+ "HP_BCLK",
+ "HP_LRCLK",
+ "HP_DOUT",
+ "HP_DIN",
+ "",
+ "",
+ "",
+ "",
+ "BT_SLIMBUS_DATA",
+ "BT_SLIMBUS_CLK",
+ "AMP_RESET_L",
+ "",
+ "FCAM_VSYNC",
+ "",
+ "AP_SKU_ID1",
+ "EC_WOV_BCLK",
+ "EC_WOV_LRCLK",
+ "EC_WOV_DOUT",
+ "",
+ "",
+ "AP_H1_SPI_MISO",
+ "AP_H1_SPI_MOSI",
+ "AP_H1_SPI_CLK",
+ "AP_H1_SPI_CS_L",
+ "",
+ "AP_SPI_CS0_L",
+ "AP_SPI_MOSI",
+ "AP_SPI_MISO",
+ "",
+ "",
+ "AP_SPI_CLK",
+ "",
+ "RFFE6_CLK",
+ "RFFE6_DATA",
+ "BOOT_CONFIG_1",
+ "BOOT_CONFIG_2",
+ "BOOT_CONFIG_0",
+ "EDP_BRIJ_EN",
+ "",
+ "USB_HS_TX_EN",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RST",
+ "UIM2_PRESENT",
+ "UIM1_DATA",
+ "UIM1_CLK",
+ "UIM1_RST",
+ "",
+ "AP_SKU_ID2",
+ "SDM_GRFC_8",
+ "SDM_GRFC_9",
+ "AP_RST_REQ",
+ "HP_IRQ",
+ "TS_RESET_L",
+ "PEN_EJECT_ODL",
+ "HUB_RST_L",
+ "FP_TO_AP_IRQ",
+ "AP_EC_INT_L",
+ "",
+ "",
+ "TS_INT_L",
+ "AP_SUSPEND_L",
+ "SDM_GRFC_3",
+ "",
+ "H1_AP_INT_ODL",
+ "QLINK_REQ",
+ "QLINK_EN",
+ "SDM_GRFC_2",
+ "BOOT_CONFIG_3",
+ "WMSS_RESET_L",
+ "SDM_GRFC_0",
+ "SDM_GRFC_1",
+ "RFFE3_DATA",
+ "RFFE3_CLK",
+ "RFFE4_DATA",
+ "RFFE4_CLK",
+ "RFFE5_DATA",
+ "RFFE5_CLK",
+ "GNSS_EN",
+ "WCI2_LTE_COEX_RXD",
+ "WCI2_LTE_COEX_TXD",
+ "AP_RAM_ID1",
+ "AP_RAM_ID2",
+ "RFFE1_DATA",
+ "RFFE1_CLK";
+};
new file mode 100644
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Cheza board device tree source
+ *
+ * Copyright 2018 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sdm845-cheza.dtsi"
+
+/ {
+ model = "Google Cheza (rev2)";
+ compatible = "google,cheza-rev2", "google,cheza", "qcom,sdm845";
+
+ /*
+ * FIXED REGULATORS (not in sdm845-cheza.dtsi) - parents above children
+ */
+
+ /*
+ * NOTE: Technically pp3500_a is not the exact same signal as
+ * pp3500_a_vbob (there's a load switch between them and the EC can
+ * control pp3500_a via "en_pp3300_a"), but from the AP's point of
+ * view they are the same.
+ */
+ pp3500_a:
+ pp3500_a_vbob: pp3500-a-vbob-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_bob";
+
+ /*
+ * Comes on automatically when pp5000_ldo comes on, which
+ * comes on automatically when ppvar_sys comes on
+ */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3500000>;
+ regulator-max-microvolt = <3500000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp3300_dx_edp: pp3300-dx-edp-regulator {
+ /* Yes, it's really 3.5 despite the name of the signal */
+ regulator-min-microvolt = <3500000>;
+ regulator-max-microvolt = <3500000>;
+
+ vin-supply = <&pp3500_a>;
+ };
+};
+
+/* FIXED REGULATOR OVERRIDES (modifications to sdm845-cheza.dtsi) */
+
+/*
+ * L19 and L28 technically go to 3.3V, but most boards have old AOP firmware
+ * that limits them to 3.0, and trying to run at 3.3V with that old firmware
+ * prevents the system from booting.
+ */
+&src_pp3000_l19a {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+};
+
+&src_pp3300_l22a {
+ /delete-property/regulator-boot-on;
+ /delete-property/regulator-always-on;
+};
+
+&src_pp3300_l28a {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+};
+
+&src_vreg_bob {
+ regulator-min-microvolt = <3500000>;
+ regulator-max-microvolt = <3500000>;
+ vin-supply = <&pp3500_a_vbob>;
+};
+
+/*
+ * NON-REGULATOR OVERRIDES
+ * (modifications to sdm845-cheza.dtsi) - alphabetized by dtsi label
+ */
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+ gpio-line-names = "AP_SPI_FP_MISO",
+ "AP_SPI_FP_MOSI",
+ "AP_SPI_FP_CLK",
+ "AP_SPI_FP_CS_L",
+ "UART_AP_TX_DBG_RX",
+ "UART_DBG_TX_AP_RX",
+ "BRIJ_SUSPEND",
+ "FP_RST_L",
+ "FCAM_EN",
+ "",
+ "EDP_BRIJ_IRQ",
+ "EC_IN_RW_ODL",
+ "",
+ "RCAM_MCLK",
+ "FCAM_MCLK",
+ "",
+ "RCAM_EN",
+ "CCI0_SDA",
+ "CCI0_SCL",
+ "CCI1_SDA",
+ "CCI1_SCL",
+ "FCAM_RST_L",
+ "FPMCU_BOOT0",
+ "PEN_RST_L",
+ "PEN_IRQ_L",
+ "FPMCU_SEL_OD",
+ "RCAM_VSYNC",
+ "ESIM_MISO",
+ "ESIM_MOSI",
+ "ESIM_CLK",
+ "ESIM_CS_L",
+ "AP_PEN_1V8_SDA",
+ "AP_PEN_1V8_SCL",
+ "AP_TS_I2C_SDA",
+ "AP_TS_I2C_SCL",
+ "RCAM_RST_L",
+ "",
+ "AP_EDP_BKLTEN",
+ "AP_BRD_ID1",
+ "BOOT_CONFIG_4",
+ "AMP_IRQ_L",
+ "EDP_BRIJ_I2C_SDA",
+ "EDP_BRIJ_I2C_SCL",
+ "EN_PP3300_DX_EDP",
+ "SD_CD_ODL",
+ "BT_UART_RTS",
+ "BT_UART_CTS",
+ "BT_UART_RXD",
+ "BT_UART_TXD",
+ "AMP_I2C_SDA",
+ "AMP_I2C_SCL",
+ "AP_BRD_ID3",
+ "",
+ "AP_EC_SPI_CLK",
+ "AP_EC_SPI_CS_L",
+ "AP_EC_SPI_MISO",
+ "AP_EC_SPI_MOSI",
+ "FORCED_USB_BOOT",
+ "AMP_BCLK",
+ "AMP_LRCLK",
+ "AMP_DOUT",
+ "AMP_DIN",
+ "AP_BRD_ID2",
+ "PEN_PDCT_L",
+ "HP_MCLK",
+ "HP_BCLK",
+ "HP_LRCLK",
+ "HP_DOUT",
+ "HP_DIN",
+ "",
+ "",
+ "",
+ "",
+ "BT_SLIMBUS_DATA",
+ "BT_SLIMBUS_CLK",
+ "AMP_RESET_L",
+ "",
+ "FCAM_VSYNC",
+ "",
+ "AP_SKU_ID1",
+ "EC_WOV_BCLK",
+ "EC_WOV_LRCLK",
+ "EC_WOV_DOUT",
+ "",
+ "",
+ "AP_H1_SPI_MISO",
+ "AP_H1_SPI_MOSI",
+ "AP_H1_SPI_CLK",
+ "AP_H1_SPI_CS_L",
+ "",
+ "AP_SPI_CS0_L",
+ "AP_SPI_MOSI",
+ "AP_SPI_MISO",
+ "",
+ "",
+ "AP_SPI_CLK",
+ "",
+ "RFFE6_CLK",
+ "RFFE6_DATA",
+ "BOOT_CONFIG_1",
+ "BOOT_CONFIG_2",
+ "BOOT_CONFIG_0",
+ "EDP_BRIJ_EN",
+ "",
+ "USB_HS_TX_EN",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RST",
+ "UIM2_PRESENT",
+ "UIM1_DATA",
+ "UIM1_CLK",
+ "UIM1_RST",
+ "",
+ "AP_SKU_ID2",
+ "SDM_GRFC_8",
+ "SDM_GRFC_9",
+ "AP_RST_REQ",
+ "HP_IRQ",
+ "TS_RESET_L",
+ "PEN_EJECT_ODL",
+ "HUB_RST_L",
+ "FP_TO_AP_IRQ",
+ "AP_EC_INT_L",
+ "",
+ "",
+ "TS_INT_L",
+ "AP_SUSPEND_L",
+ "SDM_GRFC_3",
+ "",
+ "H1_AP_INT_ODL",
+ "QLINK_REQ",
+ "QLINK_EN",
+ "SDM_GRFC_2",
+ "BOOT_CONFIG_3",
+ "WMSS_RESET_L",
+ "SDM_GRFC_0",
+ "SDM_GRFC_1",
+ "RFFE3_DATA",
+ "RFFE3_CLK",
+ "RFFE4_DATA",
+ "RFFE4_CLK",
+ "RFFE5_DATA",
+ "RFFE5_CLK",
+ "GNSS_EN",
+ "WCI2_LTE_COEX_RXD",
+ "WCI2_LTE_COEX_TXD",
+ "AP_RAM_ID1",
+ "AP_RAM_ID2",
+ "RFFE1_DATA",
+ "RFFE1_CLK";
+};
new file mode 100644
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Cheza board device tree source
+ *
+ * Copyright 2018 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sdm845-cheza.dtsi"
+
+/ {
+ model = "Google Cheza (rev3+)";
+ compatible = "google,cheza-rev15", "google,cheza-rev14",
+ "google,cheza-rev13", "google,cheza-rev12",
+ "google,cheza-rev11", "google,cheza-rev10",
+ "google,cheza-rev9", "google,cheza-rev8",
+ "google,cheza-rev7", "google,cheza-rev6",
+ "google,cheza-rev5", "google,cheza-rev4",
+ "google,cheza-rev3", "google,cheza", "qcom,sdm845";
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+ gpio-line-names = "AP_SPI_FP_MISO",
+ "AP_SPI_FP_MOSI",
+ "AP_SPI_FP_CLK",
+ "AP_SPI_FP_CS_L",
+ "UART_AP_TX_DBG_RX",
+ "UART_DBG_TX_AP_RX",
+ "BRIJ_SUSPEND",
+ "FP_RST_L",
+ "FCAM_EN",
+ "",
+ "EDP_BRIJ_IRQ",
+ "EC_IN_RW_ODL",
+ "",
+ "RCAM_MCLK",
+ "FCAM_MCLK",
+ "",
+ "RCAM_EN",
+ "CCI0_SDA",
+ "CCI0_SCL",
+ "CCI1_SDA",
+ "CCI1_SCL",
+ "FCAM_RST_L",
+ "FPMCU_BOOT0",
+ "PEN_RST_L",
+ "PEN_IRQ_L",
+ "FPMCU_SEL_OD",
+ "RCAM_VSYNC",
+ "ESIM_MISO",
+ "ESIM_MOSI",
+ "ESIM_CLK",
+ "ESIM_CS_L",
+ "AP_PEN_1V8_SDA",
+ "AP_PEN_1V8_SCL",
+ "AP_TS_I2C_SDA",
+ "AP_TS_I2C_SCL",
+ "RCAM_RST_L",
+ "",
+ "AP_EDP_BKLTEN",
+ "AP_BRD_ID0",
+ "BOOT_CONFIG_4",
+ "AMP_IRQ_L",
+ "EDP_BRIJ_I2C_SDA",
+ "EDP_BRIJ_I2C_SCL",
+ "EN_PP3300_DX_EDP",
+ "SD_CD_ODL",
+ "BT_UART_RTS",
+ "BT_UART_CTS",
+ "BT_UART_RXD",
+ "BT_UART_TXD",
+ "AMP_I2C_SDA",
+ "AMP_I2C_SCL",
+ "AP_BRD_ID2",
+ "",
+ "AP_EC_SPI_CLK",
+ "AP_EC_SPI_CS_L",
+ "AP_EC_SPI_MISO",
+ "AP_EC_SPI_MOSI",
+ "FORCED_USB_BOOT",
+ "AMP_BCLK",
+ "AMP_LRCLK",
+ "AMP_DOUT",
+ "AMP_DIN",
+ "AP_BRD_ID1",
+ "PEN_PDCT_L",
+ "HP_MCLK",
+ "HP_BCLK",
+ "HP_LRCLK",
+ "HP_DOUT",
+ "HP_DIN",
+ "",
+ "",
+ "",
+ "",
+ "BT_SLIMBUS_DATA",
+ "BT_SLIMBUS_CLK",
+ "AMP_RESET_L",
+ "",
+ "FCAM_VSYNC",
+ "",
+ "AP_SKU_ID0",
+ "EC_WOV_BCLK",
+ "EC_WOV_LRCLK",
+ "EC_WOV_DOUT",
+ "",
+ "",
+ "AP_H1_SPI_MISO",
+ "AP_H1_SPI_MOSI",
+ "AP_H1_SPI_CLK",
+ "AP_H1_SPI_CS_L",
+ "",
+ "AP_SPI_CS0_L",
+ "AP_SPI_MOSI",
+ "AP_SPI_MISO",
+ "",
+ "",
+ "AP_SPI_CLK",
+ "",
+ "RFFE6_CLK",
+ "RFFE6_DATA",
+ "BOOT_CONFIG_1",
+ "BOOT_CONFIG_2",
+ "BOOT_CONFIG_0",
+ "EDP_BRIJ_EN",
+ "",
+ "USB_HS_TX_EN",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RST",
+ "UIM2_PRESENT",
+ "UIM1_DATA",
+ "UIM1_CLK",
+ "UIM1_RST",
+ "",
+ "AP_SKU_ID1",
+ "SDM_GRFC_8",
+ "SDM_GRFC_9",
+ "AP_RST_REQ",
+ "HP_IRQ",
+ "TS_RESET_L",
+ "PEN_EJECT_ODL",
+ "HUB_RST_L",
+ "FP_TO_AP_IRQ",
+ "AP_EC_INT_L",
+ "",
+ "",
+ "TS_INT_L",
+ "AP_SUSPEND_L",
+ "SDM_GRFC_3",
+ /*
+ * AP_FLASH_WP_L is crossystem ABI. Rev3 schematics
+ * call it BIOS_FLASH_WP_R_L.
+ */
+ "AP_FLASH_WP_L",
+ "H1_AP_INT_ODL",
+ "QLINK_REQ",
+ "QLINK_EN",
+ "SDM_GRFC_2",
+ "BOOT_CONFIG_3",
+ "WMSS_RESET_L",
+ "SDM_GRFC_0",
+ "SDM_GRFC_1",
+ "RFFE3_DATA",
+ "RFFE3_CLK",
+ "RFFE4_DATA",
+ "RFFE4_CLK",
+ "RFFE5_DATA",
+ "RFFE5_CLK",
+ "GNSS_EN",
+ "WCI2_LTE_COEX_RXD",
+ "WCI2_LTE_COEX_TXD",
+ "AP_RAM_ID0",
+ "AP_RAM_ID1",
+ "RFFE1_DATA",
+ "RFFE1_CLK";
+};
new file mode 100644
@@ -0,0 +1,1317 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Cheza device tree source (common between revisions)
+ *
+ * Copyright 2018 Google LLC.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sdm845.dtsi"
+
+/* PMICs depend on spmi_bus label and so must come after SoC */
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+
+/ {
+ aliases {
+ bluetooth0 = &bluetooth;
+ hsuart0 = &uart6;
+ serial0 = &uart9;
+ wifi0 = &wifi;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&cros_ec_pwm 0>;
+ enable-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+ power-supply = <&ppvar_sys>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ap_edp_bklten>;
+ };
+
+ reserved-memory {
+ rmtfs@88f00000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0x88f00000 0x0 0x800000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ };
+ };
+
+ /* FIXED REGULATORS - parents above children */
+
+ /* This is the top level supply and variable voltage */
+ ppvar_sys: ppvar-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvar_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /* This divides ppvar_sys by 2, so voltage is variable */
+ src_vph_pwr: src-vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "src_vph_pwr";
+
+ /* EC turns on with switchcap_on_l; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp5000_a: pp5000-a-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "pp5000_a";
+
+ /* EC turns on with en_pp5000_a; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ src_vreg_bob: src-vreg-bob-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "src_vreg_bob";
+
+ /* EC turns on with vbob_en; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3600000>;
+ regulator-max-microvolt = <3600000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp3300_dx_edp: pp3300-dx-edp-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_dx_edp";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 43 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&en_pp3300_dx_edp>;
+ };
+
+ /*
+ * Apparently RPMh does not provide support for PM8998 S4 because it
+ * is always-on; model it as a fixed regulator.
+ */
+ src_pp1800_s4a: pm8998-smps4 {
+ compatible = "regulator-fixed";
+ regulator-name = "src_pp1800_s4a";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&src_vph_pwr>;
+ };
+
+ /* BOARD-SPECIFIC TOP LEVEL NODES */
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pen_eject_odl>;
+
+ pen-insert {
+ label = "Pen Insert";
+ /* Insert = low, eject = high */
+ gpios = <&tlmm 119 GPIO_ACTIVE_LOW>;
+ linux,code = <SW_PEN_INSERTED>;
+ linux,input-type = <EV_SW>;
+ wakeup-source;
+ };
+ };
+
+ panel: panel {
+ compatible ="innolux,p120zdg-bf1";
+ power-supply = <&pp3300_dx_edp>;
+ backlight = <&backlight>;
+ no-hpd;
+
+ ports {
+ panel_in: port {
+ panel_in_edp: endpoint {
+ remote-endpoint = <&sn65dsi86_out>;
+ };
+ };
+ };
+ };
+};
+
+&mpss_region {
+ reg = <0 0x8e000000 0 0x8000000>;
+};
+
+&qspi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+
+ /*
+ * In theory chip supports up to 104 MHz and controller up
+ * to 80 MHz, but above 25 MHz wasn't reliable so we'll use
+ * that for now. b:117440651
+ */
+ spi-max-frequency = <25000000>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
+ };
+};
+
+
+&apps_rsc {
+ pm8998-rpmh-regulators {
+ compatible = "qcom,pm8998-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s1-supply = <&src_vph_pwr>;
+ vdd-s2-supply = <&src_vph_pwr>;
+ vdd-s3-supply = <&src_vph_pwr>;
+ vdd-s4-supply = <&src_vph_pwr>;
+ vdd-s5-supply = <&src_vph_pwr>;
+ vdd-s6-supply = <&src_vph_pwr>;
+ vdd-s7-supply = <&src_vph_pwr>;
+ vdd-s8-supply = <&src_vph_pwr>;
+ vdd-s9-supply = <&src_vph_pwr>;
+ vdd-s10-supply = <&src_vph_pwr>;
+ vdd-s11-supply = <&src_vph_pwr>;
+ vdd-s12-supply = <&src_vph_pwr>;
+ vdd-s13-supply = <&src_vph_pwr>;
+ vdd-l1-l27-supply = <&src_pp1025_s7a>;
+ vdd-l2-l8-l17-supply = <&src_pp1350_s3a>;
+ vdd-l3-l11-supply = <&src_pp1025_s7a>;
+ vdd-l4-l5-supply = <&src_pp1025_s7a>;
+ vdd-l6-supply = <&src_vph_pwr>;
+ vdd-l7-l12-l14-l15-supply = <&src_pp2040_s5a>;
+ vdd-l9-supply = <&src_pp2040_s5a>;
+ vdd-l10-l23-l25-supply = <&src_vreg_bob>;
+ vdd-l13-l19-l21-supply = <&src_vreg_bob>;
+ vdd-l16-l28-supply = <&src_vreg_bob>;
+ vdd-l18-l22-supply = <&src_vreg_bob>;
+ vdd-l20-l24-supply = <&src_vreg_bob>;
+ vdd-l26-supply = <&src_pp1350_s3a>;
+ vin-lvs-1-2-supply = <&src_pp1800_s4a>;
+
+ src_pp1125_s2a: smps2 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ src_pp1350_s3a: smps3 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ src_pp2040_s5a: smps5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2040000>;
+ };
+
+ src_pp1025_s7a: smps7 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1028000>;
+ };
+
+ vdd_qusb_hs0:
+ vdda_hp_pcie_core:
+ vdda_mipi_csi0_0p9:
+ vdda_mipi_csi1_0p9:
+ vdda_mipi_csi2_0p9:
+ vdda_mipi_dsi0_pll:
+ vdda_mipi_dsi1_pll:
+ vdda_qlink_lv:
+ vdda_qlink_lv_ck:
+ vdda_qrefs_0p875:
+ vdda_pcie_core:
+ vdda_pll_cc_ebi01:
+ vdda_pll_cc_ebi23:
+ vdda_sp_sensor:
+ vdda_ufs1_core:
+ vdda_ufs2_core:
+ vdda_usb1_ss_core:
+ vdda_usb2_ss_core:
+ src_pp875_l1a: ldo1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_10:
+ src_pp1200_l2a: ldo2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+
+ /* TODO: why??? */
+ regulator-always-on;
+ };
+
+ pp1000_l3a_sdr845: ldo3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_wcss_cx:
+ vdd_wcss_mx:
+ vdda_wcss_pll:
+ src_pp800_l5a: ldo5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_13:
+ src_pp1800_l6a: ldo6 {
+ regulator-min-microvolt = <1856000>;
+ regulator-max-microvolt = <1856000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1800_l7a_wcn3990: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ src_pp1200_l8a: ldo8 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1248000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1800_dx_pen:
+ src_pp1800_l9a: ldo9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ src_pp1800_l10a: ldo10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1000_l11a_sdr845: ldo11 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1048000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_qfprom:
+ vdd_qfprom_sp:
+ vdda_apc1_cs_1p8:
+ vdda_gfx_cs_1p8:
+ vdda_qrefs_1p8:
+ vdda_qusb_hs0_1p8:
+ vddpx_11:
+ src_pp1800_l12a: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_2:
+ src_pp2950_l13a: ldo13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ src_pp1800_l14a: ldo14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ src_pp1800_l15a: ldo15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp2700_l16a: ldo16 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ src_pp1300_l17a: ldo17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp2700_l18a: ldo18 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /*
+ * NOTE: this rail should have been called
+ * src_pp3300_l19a in the schematic
+ */
+ src_pp3000_l19a: ldo19 {
+ regulator-min-microvolt = <3304000>;
+ regulator-max-microvolt = <3304000>;
+
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ src_pp2950_l20a: ldo20 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ src_pp2950_l21a: ldo21 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp3300_hub:
+ src_pp3300_l22a: ldo22 {
+ regulator-min-microvolt = <3304000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ /*
+ * HACK: Should add a usb hub node and driver
+ * to turn this on and off at suspend/resume time
+ */
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ pp3300_l23a_ch1_wcn3990: ldo23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdda_qusb_hs0_3p1:
+ src_pp3075_l24a: ldo24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp3300_l25a_ch0_wcn3990: ldo25 {
+ regulator-min-microvolt = <3304000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1200_hub:
+ vdda_hp_pcie_1p2:
+ vdda_hv_ebi0:
+ vdda_hv_ebi1:
+ vdda_hv_ebi2:
+ vdda_hv_ebi3:
+ vdda_mipi_csi_1p25:
+ vdda_mipi_dsi0_1p2:
+ vdda_mipi_dsi1_1p2:
+ vdda_pcie_1p2:
+ vdda_ufs1_1p2:
+ vdda_ufs2_1p2:
+ vdda_usb1_ss_1p2:
+ vdda_usb2_ss_1p2:
+ src_pp1200_l26a: ldo26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp3300_dx_pen:
+ src_pp3300_l28a: ldo28 {
+ regulator-min-microvolt = <3304000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ src_pp1800_lvs1: lvs1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ src_pp1800_lvs2: lvs2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+
+ pm8005-rpmh-regulators {
+ compatible = "qcom,pm8005-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s1-supply = <&src_vph_pwr>;
+ vdd-s2-supply = <&src_vph_pwr>;
+ vdd-s3-supply = <&src_vph_pwr>;
+ vdd-s4-supply = <&src_vph_pwr>;
+
+ src_pp600_s3c: smps3 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <600000>;
+ };
+ };
+};
+
+&dsi0 {
+ status = "okay";
+ vdda-supply = <&vdda_mipi_dsi0_1p2>;
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&sn65dsi86_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+};
+
+&dsi0_phy {
+ status = "okay";
+ vdds-supply = <&vdda_mipi_dsi0_pll>;
+};
+
+edp_brij_i2c: &i2c3 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ sn65dsi86_bridge: bridge@2d {
+ compatible = "ti,sn65dsi86";
+ reg = <0x2d>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_brij_en &edp_brij_irq>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+
+ enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+
+ vpll-supply = <&src_pp1800_s4a>;
+ vccio-supply = <&src_pp1800_s4a>;
+ vcca-supply = <&src_pp1200_l2a>;
+ vcc-supply = <&src_pp1200_l2a>;
+
+ clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+ clock-names = "refclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ sn65dsi86_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ sn65dsi86_out: endpoint {
+ remote-endpoint = <&panel_in_edp>;
+ };
+ };
+ };
+ };
+};
+
+ap_pen_1v8: &i2c11 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ digitizer@9 {
+ compatible = "wacom,w9013", "hid-over-i2c";
+ reg = <0x9>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pen_irq_l>, <&pen_pdct_l>, <&pen_rst_l>;
+
+ vdd-supply = <&pp3300_dx_pen>;
+ vddl-supply = <&pp1800_dx_pen>;
+ post-power-on-delay-ms = <100>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+
+ hid-descr-addr = <0x1>;
+ };
+};
+
+amp_i2c: &i2c12 {
+ status = "okay";
+ clock-frequency = <400000>;
+};
+
+ap_ts_i2c: &i2c14 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ touchscreen@10 {
+ compatible = "elan,ekth3500";
+ reg = <0x10>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_l &ts_reset_l>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <125 IRQ_TYPE_LEVEL_LOW>;
+
+ vcc33-supply = <&src_pp3300_l28a>;
+
+ reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&lpasscc {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_mdp {
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_cd_odl>;
+
+ vmmc-supply = <&src_pp2950_l21a>;
+ vqmmc-supply = <&vddpx_2>;
+
+ cd-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+};
+
+&spi0 {
+ status = "okay";
+ spi-max-frequency = <3000000>; /* TODO: Drop this? */
+};
+
+&spi5 {
+ status = "okay";
+ spi-max-frequency = <800000>; /* TODO: Drop this */
+ cr50@0 {
+ compatible = "google,cr50";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&h1_ap_int_odl>;
+ spi-max-frequency = <800000>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <129 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&spi10 {
+ status = "okay";
+ spi-max-frequency = <3000000>; /* TODO: Drop this? */
+
+ cros_ec: ec@0 {
+ compatible = "google,cros-ec-spi";
+ reg = <0>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <122 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ec_ap_int_l>;
+ spi-max-frequency = <3000000>;
+
+ cros_ec_pwm: ec-pwm {
+ compatible = "google,cros-ec-pwm";
+ #pwm-cells = <1>;
+ };
+
+ i2c_tunnel: i2c-tunnel {
+ compatible = "google,cros-ec-i2c-tunnel";
+ google,remote-bus = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pdupdate {
+ compatible = "google,cros-ec-pd-update";
+ };
+ };
+};
+
+#include <arm/cros-ec-keyboard.dtsi>
+#include <arm/cros-ec-sbs.dtsi>
+
+&uart6 {
+ status = "okay";
+
+ bluetooth: wcn3990-bt {
+ compatible = "qcom,wcn3990-bt";
+ vddio-supply = <&src_pp1800_s4a>;
+ vddxo-supply = <&pp1800_l7a_wcn3990>;
+ vddrf-supply = <&src_pp1300_l17a>;
+ vddch0-supply = <&pp3300_l25a_ch0_wcn3990>;
+ max-speed = <3200000>;
+ };
+};
+
+&uart9 {
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ status = "okay";
+ pinctrl-names = "init", "default";
+ pinctrl-0 = <&ufs_dev_reset_assert>;
+ pinctrl-1 = <&ufs_dev_reset_deassert>;
+
+ vcc-supply = <&src_pp2950_l20a>;
+ vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vdda_ufs1_core>;
+ vdda-pll-supply = <&vdda_ufs1_1p2>;
+};
+
+&usb_1 {
+ status = "okay";
+
+ /* We'll use this as USB 2.0 only */
+ qcom,select-utmi-as-pipe-clk;
+};
+
+&usb_1_dwc3 {
+ /*
+ * The hardware design intends this port to be hooked up in peripheral
+ * mode, so we'll hardcode it here. Some details:
+ * - SDM845 expects only a single Type C connector so it has only one
+ * native Type C port but cheza has two Type C connectors.
+ * - The only source of DP is the single native Type C port.
+ * - On cheza we want to be able to hook DP up to _either_ of the
+ * two Type C connectors and want to be able to achieve 4 lanes of DP.
+ * - When you configure a Type C port for 4 lanes of DP you lose USB3.
+ * - In order to make everything work, the native Type C port is always
+ * configured as 4-lanes DP so it's always available.
+ * - The extra USB3 port on SDM845 goes to a USB 3 hub which is then
+ * sent to the two Type C connectors.
+ * - The extra USB2 lines from the native Type C port are always
+ * setup as "peripheral" so that we can mux them over to one connector
+ * or the other if someone needs the connector configured as a gadget
+ * (but they only get USB2 speeds).
+ *
+ * All the hardware muxes would allow us to hook things up in different
+ * ways to some potential benefit for static configurations (you could
+ * achieve extra USB2 bandwidth by using two different ports for the
+ * two conenctors or possibly even get USB3 peripheral mode), but in
+ * each case you end up forcing to disconnect/reconnect an in-use
+ * USB session in some cases depending on what you hotplug into the
+ * other connector. Thus hardcoding this as peripheral makes sense.
+ */
+ dr_mode = "peripheral";
+
+ /*
+ * We always need the high speed pins as 4-lanes DP in case someone
+ * hotplugs a DP peripheral. Thus limit this port to a max of high
+ * speed.
+ */
+ maximum-speed = "high-speed";
+
+ /*
+ * We don't need the usb3-phy since we run in highspeed mode always, so
+ * re-define these properties removing the superspeed USB PHY reference.
+ */
+ phys = <&usb_1_hsphy>;
+ phy-names = "usb2-phy";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+
+ vdd-supply = <&vdda_usb1_ss_core>;
+ vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+ vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+
+ qcom,imp-res-offset-value = <8>;
+ qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+ qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+ qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_2 {
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ /* We have this hooked up to a hub and we always use in host mode */
+ dr_mode = "host";
+};
+
+&usb_2_hsphy {
+ status = "okay";
+
+ vdd-supply = <&vdda_usb2_ss_core>;
+ vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+ vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+
+ qcom,imp-res-offset-value = <8>;
+ qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
+};
+
+&usb_2_qmpphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vdda_usb2_ss_1p2>;
+ vdda-pll-supply = <&vdda_usb2_ss_core>;
+};
+
+&wifi {
+ status = "okay";
+
+ vdd-0.8-cx-mx-supply = <&src_pp800_l5a >;
+ vdd-1.8-xo-supply = <&pp1800_l7a_wcn3990>;
+ vdd-1.3-rfa-supply = <&src_pp1300_l17a>;
+ vdd-3.3-ch0-supply = <&pp3300_l25a_ch0_wcn3990>;
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+
+&qspi_cs0 {
+ pinconf {
+ pins = "gpio90";
+ bias-disable;
+ };
+};
+
+&qspi_clk {
+ pinconf {
+ pins = "gpio95";
+ bias-disable;
+ };
+};
+
+&qspi_data01 {
+ pinconf {
+ pins = "gpio91", "gpio92";
+
+ /* High-Z when no transfers; nice to park the lines */
+ bias-pull-up;
+ };
+};
+
+&qup_i2c3_default {
+ pinconf {
+ pins = "gpio41", "gpio42";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_i2c11_default {
+ pinconf {
+ pins = "gpio31", "gpio32";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_i2c12_default {
+ pinconf {
+ pins = "gpio49", "gpio50";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_i2c14_default {
+ pinconf {
+ pins = "gpio33", "gpio34";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_spi0_default {
+ pinconf {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_spi5_default {
+ pinconf {
+ pins = "gpio85", "gpio86", "gpio87", "gpio88";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_spi10_default {
+ pinconf {
+ pins = "gpio53", "gpio54", "gpio55", "gpio56";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_uart6_default {
+ /* Change pinmux to all 4 pins since CTS and RTS are connected */
+ pinmux {
+ pins = "gpio45", "gpio46",
+ "gpio47", "gpio48";
+ };
+
+ pinconf-cts {
+ /*
+ * Configure a pull-down on 45 (CTS) to match the pull of
+ * the Bluetooth module.
+ */
+ pins = "gpio45";
+ bias-pull-down;
+ };
+
+ pinconf-rts-tx {
+ /* We'll drive 46 (RTS) and 47 (TX), so no pull */
+ pins = "gpio46", "gpio47";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-rx {
+ /*
+ * Configure a pull-up on 48 (RX). This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ pins = "gpio48";
+ bias-pull-up;
+ };
+};
+
+&qup_uart9_default {
+ pinconf-tx {
+ pins = "gpio4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-rx {
+ pins = "gpio5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+};
+
+/* PINCTRL - board-specific pinctrl */
+&pm8005_gpio {
+ gpio-line-names = "",
+ "",
+ "SLB",
+ "";
+};
+
+&pm8998_adc {
+ adc-chan@ADC5_AMUX_THM1_100K_PU {
+ reg = <ADC5_AMUX_THM1_100K_PU>;
+ label = "sdm_temp";
+ };
+
+ adc-chan@ADC5_AMUX_THM2_100K_PU {
+ reg = <ADC5_AMUX_THM2_100K_PU>;
+ label = "quiet_temp";
+ };
+
+ adc-chan@ADC5_AMUX_THM3_100K_PU {
+ reg = <ADC5_AMUX_THM3_100K_PU>;
+ label = "lte_temp_1";
+ };
+
+ adc-chan@ADC5_AMUX_THM4_100K_PU {
+ reg = <ADC5_AMUX_THM4_100K_PU>;
+ label = "lte_temp_2";
+ };
+
+ adc-chan@ADC5_AMUX_THM5_100K_PU {
+ reg = <ADC5_AMUX_THM5_100K_PU>;
+ label = "charger_temp";
+ };
+};
+
+&pm8998_gpio {
+ gpio-line-names = "",
+ "",
+ "SW_CTRL",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "CFG_OPT1",
+ "WCSS_PWR_REQ",
+ "",
+ "CFG_OPT2",
+ "SLB";
+};
+
+&tlmm {
+ /*
+ * pinctrl settings for pins that have no real owners.
+ */
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&bios_flash_wp_r_l>,
+ <&ap_suspend_l_deassert>;
+
+ pinctrl-1 = <&bios_flash_wp_r_l>,
+ <&ap_suspend_l_assert>;
+
+ /*
+ * Hogs prevent usermode from changing the value. A GPIO can be both
+ * here and in the pinctrl section.
+ */
+ ap-suspend-l-hog {
+ gpio-hog;
+ gpios = <126 GPIO_ACTIVE_LOW>;
+ output-low;
+ };
+
+ ap_edp_bklten: ap-edp-bklten {
+ pinmux {
+ pins = "gpio37";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio37";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ bios_flash_wp_r_l: bios-flash-wp-r-l {
+ pinmux {
+ pins = "gpio128";
+ function = "gpio";
+ input-enable;
+ };
+
+ pinconf {
+ pins = "gpio128";
+ bias-disable;
+ };
+ };
+
+ ec_ap_int_l: ec-ap-int-l {
+ pinmux {
+ pins = "gpio122";
+ function = "gpio";
+ input-enable;
+ };
+
+ pinconf {
+ pins = "gpio122";
+ bias-pull-up;
+ };
+ };
+
+ edp_brij_en: edp-brij-en {
+ pinmux {
+ pins = "gpio102";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio102";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ edp_brij_irq: edp-brij-irq {
+ pinmux {
+ pins = "gpio10";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio10";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ en_pp3300_dx_edp: en-pp3300-dx-edp {
+ pinmux {
+ pins = "gpio43";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio43";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ h1_ap_int_odl: h1-ap-int-odl {
+ pinmux {
+ pins = "gpio129";
+ function = "gpio";
+ input-enable;
+ };
+
+ pinconf {
+ pins = "gpio129";
+ bias-pull-up;
+ };
+ };
+
+ pen_eject_odl: pen-eject-odl {
+ pinmux {
+ pins = "gpio119";
+ function = "gpio";
+ bias-pull-up;
+ };
+ };
+
+ pen_irq_l: pen-irq-l {
+ pinmux {
+ pins = "gpio24";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio24";
+
+ /* Has external pullup */
+ bias-disable;
+ };
+ };
+
+ pen_pdct_l: pen-pdct-l {
+ pinmux {
+ pins = "gpio63";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio63";
+
+ /* Has external pullup */
+ bias-disable;
+ };
+ };
+
+ pen_rst_l: pen-rst-l {
+ pinmux {
+ pins = "gpio23";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio23";
+ bias-disable;
+ drive-strength = <2>;
+
+ /*
+ * The pen driver doesn't currently support
+ * driving this reset line. By specifying
+ * output-high here we're relying on the fact
+ * that this pin has a default pulldown at boot
+ * (which makes sure the pen was in reset if it
+ * was powered) and then we set it high here to
+ * take it out of reset. Better would be if the
+ * pen driver could control this and we could
+ * remove "output-high" here.
+ */
+ output-high;
+ };
+ };
+
+ sdc2_clk: sdc2-clk {
+ pinconf {
+ pins = "sdc2_clk";
+ bias-disable;
+
+ /*
+ * It seems that mmc_test reports errors if drive
+ * strength is not 16.
+ */
+ drive-strength = <16>;
+ };
+ };
+
+ sdc2_cmd: sdc2-cmd {
+ pinconf {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <16>;
+ };
+ };
+
+ sdc2_data: sdc2-data {
+ pinconf {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <16>;
+ };
+ };
+
+ sd_cd_odl: sd-cd-odl {
+ pinmux {
+ pins = "gpio44";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio44";
+ bias-pull-up;
+ };
+ };
+
+ ts_int_l: ts-int-l {
+ pinmux {
+ pins = "gpio125";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio125";
+ bias-pull-up;
+ };
+ };
+
+ ts_reset_l: ts-reset-l {
+ pinmux {
+ pins = "gpio118";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio118";
+ bias-disable;
+ drive-strength = <2>;
+ };
+ };
+
+ ufs_dev_reset_assert: ufs_dev_reset_assert {
+ config {
+ pins = "ufs_reset";
+ bias-pull-down; /* default: pull down */
+ /*
+ * UFS_RESET driver strengths are having
+ * different values/steps compared to typical
+ * GPIO drive strengths.
+ *
+ * Following table clarifies:
+ *
+ * HDRV value | UFS_RESET | Typical GPIO
+ * (dec) | (mA) | (mA)
+ * 0 | 0.8 | 2
+ * 1 | 1.55 | 4
+ * 2 | 2.35 | 6
+ * 3 | 3.1 | 8
+ * 4 | 3.9 | 10
+ * 5 | 4.65 | 12
+ * 6 | 5.4 | 14
+ * 7 | 6.15 | 16
+ *
+ * POR value for UFS_RESET HDRV is 3 which means
+ * 3.1mA and we want to use that. Hence just
+ * specify 8mA to "drive-strength" binding and
+ * that should result into writing 3 to HDRV
+ * field.
+ */
+ drive-strength = <8>; /* default: 3.1 mA */
+ output-low; /* active low reset */
+ };
+ };
+
+ ufs_dev_reset_deassert: ufs_dev_reset_deassert {
+ config {
+ pins = "ufs_reset";
+ bias-pull-down; /* default: pull down */
+ /*
+ * default: 3.1 mA
+ * check comments under ufs_dev_reset_assert
+ */
+ drive-strength = <8>;
+ output-high; /* active low reset */
+ };
+ };
+
+ ap_suspend_l_assert: ap_suspend_l_assert {
+ config {
+ pins = "gpio126";
+ function = "gpio";
+ bias-no-pull;
+ drive-strength = <2>;
+ output-low;
+ };
+ };
+
+ ap_suspend_l_deassert: ap_suspend_l_deassert {
+ config {
+ pins = "gpio126";
+ function = "gpio";
+ bias-no-pull;
+ drive-strength = <2>;
+ output-high;
+ };
+ };
+};