| Message ID | 1557832703-42620-1-git-send-email-gengdongjiu@huawei.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | Add ARMv8 RAS virtualization support in QEMU | expand |
Hi All,
for this series patch, we can use below simple method to test:
1). Apply below hard code change after applying this series patch:
diff --git a/cpus.c b/cpus.c
index e58e7ab..7149f54 100644
--- a/cpus.c
+++ b/cpus.c
@@ -1131,6 +1131,8 @@ static void sigbus_reraise(void)
static void sigbus_handler(int n, siginfo_t *siginfo, void *ctx)
{
+ siginfo->si_code = BUS_MCEERR_AO;
+
if (siginfo->si_code != BUS_MCEERR_AO && siginfo->si_code != BUS_MCEERR_AR) {
sigbus_reraise();
}
diff --git a/target/arm/kvm64.c b/target/arm/kvm64.c
index d2eac28..6c9956e 100644
--- a/target/arm/kvm64.c
+++ b/target/arm/kvm64.c
@@ -1035,20 +1035,23 @@ int kvm_arch_get_registers(CPUState *cs)
void kvm_arch_on_sigbus_vcpu(CPUState *c, int code, void *addr)
{
+#if 0
ram_addr_t ram_addr;
- hwaddr paddr;
-
+#endif
+ hwaddr paddr = 0x400a1000;
assert(code == BUS_MCEERR_AR || code == BUS_MCEERR_AO);
+#if 0
if (acpi_enabled && addr) {
ram_addr = qemu_ram_addr_from_host(addr);
if (ram_addr != RAM_ADDR_INVALID &&
kvm_physical_memory_addr_from_host(c->kvm_state, addr, &paddr)) {
kvm_hwpoison_page_add(ram_addr);
+#endif
/* Asynchronous signal will be masked by main thread, so
* only handle synchronous signal.
*/
- if (code == BUS_MCEERR_AR) {
+ if (code == BUS_MCEERR_AR || BUS_MCEERR_AO == code) {
kvm_cpu_synchronize_state(c);
if (GHES_CPER_FAIL != ghes_record_errors(ACPI_HEST_NOTIFY_SEA, paddr)) {
kvm_inject_arm_sea(c);
@@ -1057,11 +1060,13 @@ void kvm_arch_on_sigbus_vcpu(CPUState *c, int code, void *addr)
}
}
return;
+#if 0
}
fprintf(stderr, "Hardware memory error for memory used by "
"QEMU itself instead of guest system!\n");
}
+#endif
if (code == BUS_MCEERR_AR) {
fprintf(stderr, "Hardware memory error!\n");
exit(1);
2) In Arm64 machine run below command to run a virtual machine with kvm disabled, and enable bios:
./qemu-system-aarch64 -cpu cortex-a57 -machine virt,gic-version=3 -smp 4 -nographic -kernel Image -bios QEMU_EFI.fd -append "rdinit=/init console=ttyAMA0 mem=512M root=/dev/ram0 earlycon=pl011,0x9000000 rw" -initrd guestfs_new.cpio.gz
3) Deliver SGIBUS signal to QEMU:
kill -s SIGBUS 11522
4) then you can see QEMU record the error memory address to APEI table, and inject a SEA to guest, for example:
[ 75.514270] {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 1
[ 75.531858] {1}[Hardware Error]: event severity: recoverable
[ 75.535095] {1}[Hardware Error]: Error 0, type: recoverable
[ 75.539223] {1}[Hardware Error]: section_type: memory error
[ 75.543878] {1}[Hardware Error]: physical_address: 0x00000000400a1000
[ 75.548696] {1}[Hardware Error]: error_type: 0, unknown
[ 75.577156] Internal error: synchronous external abort: 96000410 [#1] PREEMPT SMP
On 2019/5/14 19:18, Dongjiu Geng wrote:
> In the ARMv8 platform, the CPU error type are synchronous external
> abort(SEA) and SError Interrupt (SEI). If exception happens to guest,
> sometimes guest itself do the recovery is better, because host
> does not know guest's detailed information. For example, if a guest
> user-space application happen exception, host does not which application
> encounter errors.
>
> For the ARMv8 SEA/SEI, KVM or host kernel delivers SIGBUS to notify user
> space. After user space gets the notification, it will record the CPER
> to guest GHES buffer for guest and inject a exception or IRQ to guest.
>
> In the current implement, if the SIGBUS is BUS_MCEERR_AR, we will
> treat it as synchronous exception, and use ARMv8 SEA notification type
> to notify guest after recording CPER for guest;
>
> This series patches are based on Qemu 4.0, which have two parts:
> 1. Generate APEI/GHES table.
> 2. Handle the SIGBUS signal, record the CPER in runtime and fill into guest memory,
> then according to SIGBUS type to notify guest.
>
> Whole solution was suggested by James(james.morse@arm.com); APEI part solution is suggested by
> Laszlo(lersek@redhat.com). Shown some discussion in [1].
>
>
> This series patches have already tested on ARM64 platform with RAS feature enabled:
> Show the APEI part verification result in [2]
> Show the BUS_MCEERR_AR SIGBUS handling verification result in [3]
>
> ---
> change since v16:
> 1. check whether ACPI table is enabled when handling the memory error in the SIGBUS handler.
>
> Change since v15:
> 1. Add a doc-comment in the proper format for 'include/exec/ram_addr.h'
> 2. Remove write_part_cpustate_to_list() because there is another bug fix patch
> has been merged "arm: Allow system registers for KVM guests to be changed by QEMU code"
> 3. Add some comments for kvm_inject_arm_sea() in 'target/arm/kvm64.c'
> 4. Compare the arm_current_el() return value to 0,1,2,3, not to PSTATE_MODE_* constants.
> 5. Change the RAS support wasn't introduced before 4.1 QEMU version.
> 6. Move the no_ras flag patch to begin in this series
>
> Change since v14:
> 1. Remove the BUS_MCEERR_AO handling logic because this asynchronous signal was masked by main thread
> 2. Address some Igor Mammedov's comments(ACPI part)
> 1) change the comments for the enum AcpiHestNotifyType definition and remove ditto in patch 1
> 2) change some patch commit messages and separate "APEI GHES table generation" patch to more patches.
> 3. Address some peter's comments(arm64 Synchronous External Abort injection)
> 1) change some code notes
> 2) using arm_current_el() for current EL
> 2) use the helper functions for those (syn_data_abort_*).
>
> Change since v13:
> 1. Move the patches that set guest ESR and inject virtual SError out of this series
> 2. Clean and optimize the APEI part patches
> 3. Update the commit messages and add some comments for the code
>
> Change since v12:
> 1. Address Paolo's comments to move HWPoisonPage definition to accel/kvm/kvm-all.c
> 2. Only call kvm_cpu_synchronize_state() when get the BUS_MCEERR_AR signal
> 3. Only add and enable GPIO-Signal and ARMv8 SEA two hardware error sources
> 4. Address Michael's comments to not sync SPDX from Linux kernel header file
>
> Change since v11:
> Address James's comments(james.morse@arm.com)
> 1. Check whether KVM has the capability to to set ESR instead of detecting host CPU RAS capability
> 2. For SIGBUS_MCEERR_AR SIGBUS, use Synchronous-External-Abort(SEA) notification type
> for SIGBUS_MCEERR_AO SIGBUS, use GPIO-Signal notification
>
>
> Address Shannon's comments(for ACPI part):
> 1. Unify hest_ghes.c and hest_ghes.h license declaration
> 2. Remove unnecessary including "qmp-commands.h" in hest_ghes.c
> 3. Unconditionally add guest APEI table based on James's comments(james.morse@arm.com)
> 4. Add a option to virt machine for migration compatibility. On new virt machine it's on
> by default while off for old ones, we enabled it since 2.12
> 5. Refer to the ACPI spec version which introduces Hardware Error Notification first time
> 6. Add ACPI_HEST_NOTIFY_RESERVED notification type
>
> Address Igor's comments(for ACPI part):
> 1. Add doc patch first which will describe how it's supposed to work between QEMU/firmware/guest
> OS with expected flows.
> 2. Move APEI diagrams into doc/spec patch
> 3. Remove redundant g_malloc in ghes_record_cper()
> 4. Use build_append_int_noprefix() API to compose whole error status block and whole APEI table,
> and try to get rid of most structures in patch 1, as they will be left unused after that
> 5. Reuse something like https://github.com/imammedo/qemu/commit/3d2fd6d13a3ea298d2ee814835495ce6241d085c
> to build GAS
> 6. Remove much offsetof() in the function
> 7. Build independent tables first and only then build dependent tables passing to it pointers
> to previously build table if necessary.
> 8. Redefine macro GHES_ACPI_HEST_NOTIFY_RESERVED to ACPI_HEST_ERROR_SOURCE_COUNT to avoid confusion
>
>
> Address Peter Maydell's comments
> 1. linux-headers is done as a patch of their own created using scripts/update-linux-headers.sh run against a
> mainline kernel tree
> 2. Tested whether this patchset builds OK on aarch32
> 3. Abstract Hwpoison page adding code out properly into a cpu-independent source file from target/i386/kvm.c,
> such as kvm-all.c
> 4. Add doc-comment formatted documentation comment for new globally-visible function prototype in a header
>
> ---
> [1]:
> https://lkml.org/lkml/2017/2/27/246
> https://patchwork.kernel.org/patch/9633105/
> https://patchwork.kernel.org/patch/9925227/
>
> [2]:
> Note: the UEFI(QEMU_EFI.fd) is needed if guest want to use ACPI table.
>
> After guest boot up, dump the APEI table, then can see the initialized table
> (1) # iasl -p ./HEST -d /sys/firmware/acpi/tables/HEST
> (2) # cat HEST.dsl
> /*
> * Intel ACPI Component Architecture
> * AML/ASL+ Disassembler version 20170728 (64-bit version)
> * Copyright (c) 2000 - 2017 Intel Corporation
> *
> * Disassembly of /sys/firmware/acpi/tables/HEST, Mon Sep 5 07:59:17 2016
> *
> * ACPI Data Table [HEST]
> *
> * Format: [HexOffset DecimalOffset ByteLength] FieldName : FieldValue
> */
>
> ..................................................................................
> [308h 0776 2] Subtable Type : 000A [Generic Hardware Error Source V2]
> [30Ah 0778 2] Source Id : 0001
> [30Ch 0780 2] Related Source Id : FFFF
> [30Eh 0782 1] Reserved : 00
> [30Fh 0783 1] Enabled : 01
> [310h 0784 4] Records To Preallocate : 00000001
> [314h 0788 4] Max Sections Per Record : 00000001
> [318h 0792 4] Max Raw Data Length : 00001000
>
> [31Ch 0796 12] Error Status Address : [Generic Address Structure]
> [31Ch 0796 1] Space ID : 00 [SystemMemory]
> [31Dh 0797 1] Bit Width : 40
> [31Eh 0798 1] Bit Offset : 00
> [31Fh 0799 1] Encoded Access Width : 04 [QWord Access:64]
> [320h 0800 8] Address : 00000000785D0040
>
> [328h 0808 28] Notify : [Hardware Error Notification Structure]
> [328h 0808 1] Notify Type : 08 [SEA]
> [329h 0809 1] Notify Length : 1C
> [32Ah 0810 2] Configuration Write Enable : 0000
> [32Ch 0812 4] PollInterval : 00000000
> [330h 0816 4] Vector : 00000000
> [334h 0820 4] Polling Threshold Value : 00000000
> [338h 0824 4] Polling Threshold Window : 00000000
> [33Ch 0828 4] Error Threshold Value : 00000000
> [340h 0832 4] Error Threshold Window : 00000000
>
> [344h 0836 4] Error Status Block Length : 00001000
> [348h 0840 12] Read Ack Register : [Generic Address Structure]
> [348h 0840 1] Space ID : 00 [SystemMemory]
> [349h 0841 1] Bit Width : 40
> [34Ah 0842 1] Bit Offset : 00
> [34Bh 0843 1] Encoded Access Width : 04 [QWord Access:64]
> [34Ch 0844 8] Address : 00000000785D0098
>
> [354h 0852 8] Read Ack Preserve : 00000000FFFFFFFE
> [35Ch 0860 8] Read Ack Write : 0000000000000001
>
> .....................................................................................
>
> (3) After a synchronous external abort(SEA) happen, Qemu receive a SIGBUS and
> filled the CPER into guest GHES memory. For example, according to above table,
> the address that contains the physical address of a block of memory that holds
> the error status data for this abort is 0x00000000785D0040
> (4) the address for SEA notification error source is 0x785d80b0
> (qemu) xp /1 0x00000000785D0040
> 00000000785d0040: 0x785d80b0
>
> (5) check the content of generic error status block and generic error data entry
> (qemu) xp /100x 0x785d80b0
> 00000000785d80b0: 0x00000001 0x00000000 0x00000000 0x00000098
> 00000000785d80c0: 0x00000000 0xa5bc1114 0x4ede6f64 0x833e63b8
> 00000000785d80d0: 0xb1837ced 0x00000000 0x00000300 0x00000050
> 00000000785d80e0: 0x00000000 0x00000000 0x00000000 0x00000000
> 00000000785d80f0: 0x00000000 0x00000000 0x00000000 0x00000000
> 00000000785d8100: 0x00000000 0x00000000 0x00000000 0x00004002
> (6) check the OSPM's ACK value(for example SEA)
> /* Before OSPM acknowledges the error, check the ACK value */
> (qemu) xp /1 0x00000000785D0098
> 00000000785d00f0: 0x00000000
>
> /* After OSPM acknowledges the error, check the ACK value, it change to 1 from 0 */
> (qemu) xp /1 0x00000000785D0098
> 00000000785d00f0: 0x00000001
>
> [3]: KVM deliver "BUS_MCEERR_AR" to Qemu, Qemu record the guest CPER and inject
> synchronous external abort to notify guest, then guest do the recovery.
>
> [ 1552.516170] Synchronous External Abort: synchronous external abort (0x92000410) at 0x000000003751c6b4
> [ 1553.074073] {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 8
> [ 1553.081654] {1}[Hardware Error]: event severity: recoverable
> [ 1554.034191] {1}[Hardware Error]: Error 0, type: recoverable
> [ 1554.037934] {1}[Hardware Error]: section_type: memory error
> [ 1554.513261] {1}[Hardware Error]: physical_address: 0x0000000040fa6000
> [ 1554.513944] {1}[Hardware Error]: error_type: 0, unknown
> [ 1555.041451] Memory failure: 0x40fa6: Killing mca-recover:1296 due to hardware memory corruption
> [ 1555.373116] Memory failure: 0x40fa6: recovery action for dirty LRU page: Recovered
>
>
>
> Dongjiu Geng (10):
> hw/arm/virt: Add RAS platform version for migration
> ACPI: add some GHES structures and macros definition
> acpi: add build_append_ghes_notify() helper for Hardware Error
> Notification
> acpi: add build_append_ghes_generic_data() helper for Generic Error
> Data Entry
> acpi: add build_append_ghes_generic_status() helper for Generic Error
> Status Block
> docs: APEI GHES generation and CPER record description
> ACPI: Add APEI GHES table generation support
> KVM: Move related hwpoison page functions to accel/kvm/ folder
> target-arm: kvm64: inject synchronous External Abort
> target-arm: kvm64: handle SIGBUS signal from kernel or KVM
>
> accel/kvm/kvm-all.c | 33 ++++
> default-configs/arm-softmmu.mak | 1 +
> docs/specs/acpi_hest_ghes.txt | 97 +++++++++++
> hw/acpi/Kconfig | 4 +
> hw/acpi/Makefile.objs | 1 +
> hw/acpi/acpi_ghes.c | 348 ++++++++++++++++++++++++++++++++++++++++
> hw/acpi/aml-build.c | 70 ++++++++
> hw/arm/virt-acpi-build.c | 12 ++
> hw/arm/virt.c | 6 +
> include/exec/ram_addr.h | 24 +++
> include/hw/acpi/acpi-defs.h | 52 ++++++
> include/hw/acpi/acpi_ghes.h | 83 ++++++++++
> include/hw/acpi/aml-build.h | 21 +++
> include/hw/arm/virt.h | 1 +
> include/sysemu/kvm.h | 2 +-
> target/arm/internals.h | 5 +-
> target/arm/kvm.c | 3 +
> target/arm/kvm64.c | 73 +++++++++
> target/arm/op_helper.c | 2 +-
> target/i386/kvm.c | 34 +---
> 20 files changed, 835 insertions(+), 37 deletions(-)
> create mode 100644 docs/specs/acpi_hest_ghes.txt
> create mode 100644 hw/acpi/acpi_ghes.c
> create mode 100644 include/hw/acpi/acpi_ghes.h
>
ping...
发件人：gengdongjiu <gengdongjiu@huawei.com>
收件人：pbonzini@redhat.com <pbonzini@redhat.com>;mst@redhat.com <mst@redhat.com>;imammedo@redhat.com <imammedo@redhat.com>;shannon.zhaosl@gmail.com <shannon.zhaosl@gmail.com>;peter.maydell@linaro.org <peter.maydell@linaro.org>;lersek@redhat.com <lersek@redhat.com>;james.morse@arm.com <james.morse@arm.com>;mtosatti@redhat.com <mtosatti@redhat.com>;rth@twiddle.net <rth@twiddle.net>;ehabkost@redhat.com <ehabkost@redhat.com>;zhengxiang (A) <zhengxiang9@huawei.com>;Jonathan Cameron <jonathan.cameron@huawei.com>;xuwei (O) <xuwei5@huawei.com>;kvm@vger.kernel.org <kvm@vger.kernel.org>;qemu-devel@nongnu.org <qemu-devel@nongnu.org>;qemu-arm@nongnu.org <qemu-arm@nongnu.org>;Linuxarm <linuxarm@huawei.com>
时间：2019-05-15 17:40:49
主 题：Re: [PATCH v17 00/10] Add ARMv8 RAS virtualization support in QEMU
Hi All,
for this series patch, we can use below simple method to test:
1). Apply below hard code change after applying this series patch:
diff --git a/cpus.c b/cpus.c
index e58e7ab..7149f54 100644
--- a/cpus.c
+++ b/cpus.c
@@ -1131,6 +1131,8 @@ static void sigbus_reraise(void)
static void sigbus_handler(int n, siginfo_t *siginfo, void *ctx)
{
+ siginfo->si_code = BUS_MCEERR_AO;
+
if (siginfo->si_code != BUS_MCEERR_AO && siginfo->si_code != BUS_MCEERR_AR) {
sigbus_reraise();
}
diff --git a/target/arm/kvm64.c b/target/arm/kvm64.c
index d2eac28..6c9956e 100644
--- a/target/arm/kvm64.c
+++ b/target/arm/kvm64.c
@@ -1035,20 +1035,23 @@ int kvm_arch_get_registers(CPUState *cs)
void kvm_arch_on_sigbus_vcpu(CPUState *c, int code, void *addr)
{
+#if 0
ram_addr_t ram_addr;
- hwaddr paddr;
-
+#endif
+ hwaddr paddr = 0x400a1000;
assert(code == BUS_MCEERR_AR || code == BUS_MCEERR_AO);
+#if 0
if (acpi_enabled && addr) {
ram_addr = qemu_ram_addr_from_host(addr);
if (ram_addr != RAM_ADDR_INVALID &&
kvm_physical_memory_addr_from_host(c->kvm_state, addr, &paddr)) {
kvm_hwpoison_page_add(ram_addr);
+#endif
/* Asynchronous signal will be masked by main thread, so
* only handle synchronous signal.
*/
- if (code == BUS_MCEERR_AR) {
+ if (code == BUS_MCEERR_AR || BUS_MCEERR_AO == code) {
kvm_cpu_synchronize_state(c);
if (GHES_CPER_FAIL != ghes_record_errors(ACPI_HEST_NOTIFY_SEA, paddr)) {
kvm_inject_arm_sea(c);
@@ -1057,11 +1060,13 @@ void kvm_arch_on_sigbus_vcpu(CPUState *c, int code, void *addr)
}
}
return;
+#if 0
}
fprintf(stderr, "Hardware memory error for memory used by "
"QEMU itself instead of guest system!\n");
}
+#endif
if (code == BUS_MCEERR_AR) {
fprintf(stderr, "Hardware memory error!\n");
exit(1);
2) In Arm64 machine run below command to run a virtual machine with kvm disabled, and enable bios:
./qemu-system-aarch64 -cpu cortex-a57 -machine virt,gic-version=3 -smp 4 -nographic -kernel Image -bios QEMU_EFI.fd -append "rdinit=/init console=ttyAMA0 mem=512M root=/dev/ram0 earlycon=pl011,0x9000000 rw" -initrd guestfs_new.cpio.gz
3) Deliver SGIBUS signal to QEMU:
kill -s SIGBUS 11522
4) then you can see QEMU record the error memory address to APEI table, and inject a SEA to guest, for example:
[ 75.514270] {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 1
[ 75.531858] {1}[Hardware Error]: event severity: recoverable
[ 75.535095] {1}[Hardware Error]: Error 0, type: recoverable
[ 75.539223] {1}[Hardware Error]: section_type: memory error
[ 75.543878] {1}[Hardware Error]: physical_address: 0x00000000400a1000
[ 75.548696] {1}[Hardware Error]: error_type: 0, unknown
[ 75.577156] Internal error: synchronous external abort: 96000410 [#1] PREEMPT SMP
On 2019/5/14 19:18, Dongjiu Geng wrote:
> In the ARMv8 platform, the CPU error type are synchronous external
> abort(SEA) and SError Interrupt (SEI). If exception happens to guest,
> sometimes guest itself do the recovery is better, because host
> does not know guest's detailed information. For example, if a guest
> user-space application happen exception, host does not which application
> encounter errors.
>
> For the ARMv8 SEA/SEI, KVM or host kernel delivers SIGBUS to notify user
> space. After user space gets the notification, it will record the CPER
> to guest GHES buffer for guest and inject a exception or IRQ to guest.
>
> In the current implement, if the SIGBUS is BUS_MCEERR_AR, we will
> treat it as synchronous exception, and use ARMv8 SEA notification type
> to notify guest after recording CPER for guest;
>
> This series patches are based on Qemu 4.0, which have two parts:
> 1. Generate APEI/GHES table.
> 2. Handle the SIGBUS signal, record the CPER in runtime and fill into guest memory,
> then according to SIGBUS type to notify guest.
>
> Whole solution was suggested by James(james.morse@arm.com); APEI part solution is suggested by
> Laszlo(lersek@redhat.com). Shown some discussion in [1].
>
>
> This series patches have already tested on ARM64 platform with RAS feature enabled:
> Show the APEI part verification result in [2]
> Show the BUS_MCEERR_AR SIGBUS handling verification result in [3]
>
> ---
> change since v16:
> 1. check whether ACPI table is enabled when handling the memory error in the SIGBUS handler.
>
> Change since v15:
> 1. Add a doc-comment in the proper format for 'include/exec/ram_addr.h'
> 2. Remove write_part_cpustate_to_list() because there is another bug fix patch
> has been merged "arm: Allow system registers for KVM guests to be changed by QEMU code"
> 3. Add some comments for kvm_inject_arm_sea() in 'target/arm/kvm64.c'
> 4. Compare the arm_current_el() return value to 0,1,2,3, not to PSTATE_MODE_* constants.
> 5. Change the RAS support wasn't introduced before 4.1 QEMU version.
> 6. Move the no_ras flag patch to begin in this series
>
> Change since v14:
> 1. Remove the BUS_MCEERR_AO handling logic because this asynchronous signal was masked by main thread
> 2. Address some Igor Mammedov's comments(ACPI part)
> 1) change the comments for the enum AcpiHestNotifyType definition and remove ditto in patch 1
> 2) change some patch commit messages and separate "APEI GHES table generation" patch to more patches.
> 3. Address some peter's comments(arm64 Synchronous External Abort injection)
> 1) change some code notes
> 2) using arm_current_el() for current EL
> 2) use the helper functions for those (syn_data_abort_*).
>
> Change since v13:
> 1. Move the patches that set guest ESR and inject virtual SError out of this series
> 2. Clean and optimize the APEI part patches
> 3. Update the commit messages and add some comments for the code
>
> Change since v12:
> 1. Address Paolo's comments to move HWPoisonPage definition to accel/kvm/kvm-all.c
> 2. Only call kvm_cpu_synchronize_state() when get the BUS_MCEERR_AR signal
> 3. Only add and enable GPIO-Signal and ARMv8 SEA two hardware error sources
> 4. Address Michael's comments to not sync SPDX from Linux kernel header file
>
> Change since v11:
> Address James's comments(james.morse@arm.com)
> 1. Check whether KVM has the capability to to set ESR instead of detecting host CPU RAS capability
> 2. For SIGBUS_MCEERR_AR SIGBUS, use Synchronous-External-Abort(SEA) notification type
> for SIGBUS_MCEERR_AO SIGBUS, use GPIO-Signal notification
>
>
> Address Shannon's comments(for ACPI part):
> 1. Unify hest_ghes.c and hest_ghes.h license declaration
> 2. Remove unnecessary including "qmp-commands.h" in hest_ghes.c
> 3. Unconditionally add guest APEI table based on James's comments(james.morse@arm.com)
> 4. Add a option to virt machine for migration compatibility. On new virt machine it's on
> by default while off for old ones, we enabled it since 2.12
> 5. Refer to the ACPI spec version which introduces Hardware Error Notification first time
> 6. Add ACPI_HEST_NOTIFY_RESERVED notification type
>
> Address Igor's comments(for ACPI part):
> 1. Add doc patch first which will describe how it's supposed to work between QEMU/firmware/guest
> OS with expected flows.
> 2. Move APEI diagrams into doc/spec patch
> 3. Remove redundant g_malloc in ghes_record_cper()
> 4. Use build_append_int_noprefix() API to compose whole error status block and whole APEI table,
> and try to get rid of most structures in patch 1, as they will be left unused after that
> 5. Reuse something like https://github.com/imammedo/qemu/commit/3d2fd6d13a3ea298d2ee814835495ce6241d085c
> to build GAS
> 6. Remove much offsetof() in the function
> 7. Build independent tables first and only then build dependent tables passing to it pointers
> to previously build table if necessary.
> 8. Redefine macro GHES_ACPI_HEST_NOTIFY_RESERVED to ACPI_HEST_ERROR_SOURCE_COUNT to avoid confusion
>
>
> Address Peter Maydell's comments
> 1. linux-headers is done as a patch of their own created using scripts/update-linux-headers.sh run against a
> mainline kernel tree
> 2. Tested whether this patchset builds OK on aarch32
> 3. Abstract Hwpoison page adding code out properly into a cpu-independent source file from target/i386/kvm.c,
> such as kvm-all.c
> 4. Add doc-comment formatted documentation comment for new globally-visible function prototype in a header
>
> ---
> [1]:
> https://lkml.org/lkml/2017/2/27/246
> https://patchwork.kernel.org/patch/9633105/
> https://patchwork.kernel.org/patch/9925227/
>
> [2]:
> Note: the UEFI(QEMU_EFI.fd) is needed if guest want to use ACPI table.
>
> After guest boot up, dump the APEI table, then can see the initialized table
> (1) # iasl -p ./HEST -d /sys/firmware/acpi/tables/HEST
> (2) # cat HEST.dsl
> /*
> * Intel ACPI Component Architecture
> * AML/ASL+ Disassembler version 20170728 (64-bit version)
> * Copyright (c) 2000 - 2017 Intel Corporation
> *
> * Disassembly of /sys/firmware/acpi/tables/HEST, Mon Sep 5 07:59:17 2016
> *
> * ACPI Data Table [HEST]
> *
> * Format: [HexOffset DecimalOffset ByteLength] FieldName : FieldValue
> */
>
> ..................................................................................
> [308h 0776 2] Subtable Type : 000A [Generic Hardware Error Source V2]
> [30Ah 0778 2] Source Id : 0001
> [30Ch 0780 2] Related Source Id : FFFF
> [30Eh 0782 1] Reserved : 00
> [30Fh 0783 1] Enabled : 01
> [310h 0784 4] Records To Preallocate : 00000001
> [314h 0788 4] Max Sections Per Record : 00000001
> [318h 0792 4] Max Raw Data Length : 00001000
>
> [31Ch 0796 12] Error Status Address : [Generic Address Structure]
> [31Ch 0796 1] Space ID : 00 [SystemMemory]
> [31Dh 0797 1] Bit Width : 40
> [31Eh 0798 1] Bit Offset : 00
> [31Fh 0799 1] Encoded Access Width : 04 [QWord Access:64]
> [320h 0800 8] Address : 00000000785D0040
>
> [328h 0808 28] Notify : [Hardware Error Notification Structure]
> [328h 0808 1] Notify Type : 08 [SEA]
> [329h 0809 1] Notify Length : 1C
> [32Ah 0810 2] Configuration Write Enable : 0000
> [32Ch 0812 4] PollInterval : 00000000
> [330h 0816 4] Vector : 00000000
> [334h 0820 4] Polling Threshold Value : 00000000
> [338h 0824 4] Polling Threshold Window : 00000000
> [33Ch 0828 4] Error Threshold Value : 00000000
> [340h 0832 4] Error Threshold Window : 00000000
>
> [344h 0836 4] Error Status Block Length : 00001000
> [348h 0840 12] Read Ack Register : [Generic Address Structure]
> [348h 0840 1] Space ID : 00 [SystemMemory]
> [349h 0841 1] Bit Width : 40
> [34Ah 0842 1] Bit Offset : 00
> [34Bh 0843 1] Encoded Access Width : 04 [QWord Access:64]
> [34Ch 0844 8] Address : 00000000785D0098
>
> [354h 0852 8] Read Ack Preserve : 00000000FFFFFFFE
> [35Ch 0860 8] Read Ack Write : 0000000000000001
>
> .....................................................................................
>
> (3) After a synchronous external abort(SEA) happen, Qemu receive a SIGBUS and
> filled the CPER into guest GHES memory. For example, according to above table,
> the address that contains the physical address of a block of memory that holds
> the error status data for this abort is 0x00000000785D0040
> (4) the address for SEA notification error source is 0x785d80b0
> (qemu) xp /1 0x00000000785D0040
> 00000000785d0040: 0x785d80b0
>
> (5) check the content of generic error status block and generic error data entry
> (qemu) xp /100x 0x785d80b0
> 00000000785d80b0: 0x00000001 0x00000000 0x00000000 0x00000098
> 00000000785d80c0: 0x00000000 0xa5bc1114 0x4ede6f64 0x833e63b8
> 00000000785d80d0: 0xb1837ced 0x00000000 0x00000300 0x00000050
> 00000000785d80e0: 0x00000000 0x00000000 0x00000000 0x00000000
> 00000000785d80f0: 0x00000000 0x00000000 0x00000000 0x00000000
> 00000000785d8100: 0x00000000 0x00000000 0x00000000 0x00004002
> (6) check the OSPM's ACK value(for example SEA)
> /* Before OSPM acknowledges the error, check the ACK value */
> (qemu) xp /1 0x00000000785D0098
> 00000000785d00f0: 0x00000000
>
> /* After OSPM acknowledges the error, check the ACK value, it change to 1 from 0 */
> (qemu) xp /1 0x00000000785D0098
> 00000000785d00f0: 0x00000001
>
> [3]: KVM deliver "BUS_MCEERR_AR" to Qemu, Qemu record the guest CPER and inject
> synchronous external abort to notify guest, then guest do the recovery.
>
> [ 1552.516170] Synchronous External Abort: synchronous external abort (0x92000410) at 0x000000003751c6b4
> [ 1553.074073] {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 8
> [ 1553.081654] {1}[Hardware Error]: event severity: recoverable
> [ 1554.034191] {1}[Hardware Error]: Error 0, type: recoverable
> [ 1554.037934] {1}[Hardware Error]: section_type: memory error
> [ 1554.513261] {1}[Hardware Error]: physical_address: 0x0000000040fa6000
> [ 1554.513944] {1}[Hardware Error]: error_type: 0, unknown
> [ 1555.041451] Memory failure: 0x40fa6: Killing mca-recover:1296 due to hardware memory corruption
> [ 1555.373116] Memory failure: 0x40fa6: recovery action for dirty LRU page: Recovered
>
>
>
> Dongjiu Geng (10):
> hw/arm/virt: Add RAS platform version for migration
> ACPI: add some GHES structures and macros definition
> acpi: add build_append_ghes_notify() helper for Hardware Error
> Notification
> acpi: add build_append_ghes_generic_data() helper for Generic Error
> Data Entry
> acpi: add build_append_ghes_generic_status() helper for Generic Error
> Status Block
> docs: APEI GHES generation and CPER record description
> ACPI: Add APEI GHES table generation support
> KVM: Move related hwpoison page functions to accel/kvm/ folder
> target-arm: kvm64: inject synchronous External Abort
> target-arm: kvm64: handle SIGBUS signal from kernel or KVM
>
> accel/kvm/kvm-all.c | 33 ++++
> default-configs/arm-softmmu.mak | 1 +
> docs/specs/acpi_hest_ghes.txt | 97 +++++++++++
> hw/acpi/Kconfig | 4 +
> hw/acpi/Makefile.objs | 1 +
> hw/acpi/acpi_ghes.c | 348 ++++++++++++++++++++++++++++++++++++++++
> hw/acpi/aml-build.c | 70 ++++++++
> hw/arm/virt-acpi-build.c | 12 ++
> hw/arm/virt.c | 6 +
> include/exec/ram_addr.h | 24 +++
> include/hw/acpi/acpi-defs.h | 52 ++++++
> include/hw/acpi/acpi_ghes.h | 83 ++++++++++
> include/hw/acpi/aml-build.h | 21 +++
> include/hw/arm/virt.h | 1 +
> include/sysemu/kvm.h | 2 +-
> target/arm/internals.h | 5 +-
> target/arm/kvm.c | 3 +
> target/arm/kvm64.c | 73 +++++++++
> target/arm/op_helper.c | 2 +-
> target/i386/kvm.c | 34 +---
> 20 files changed, 835 insertions(+), 37 deletions(-)
> create mode 100644 docs/specs/acpi_hest_ghes.txt
> create mode 100644 hw/acpi/acpi_ghes.c
> create mode 100644 include/hw/acpi/acpi_ghes.h
>
In the ARMv8 platform, the CPU error type are synchronous external abort(SEA) and SError Interrupt (SEI). If exception happens to guest, sometimes guest itself do the recovery is better, because host does not know guest's detailed information. For example, if a guest user-space application happen exception, host does not which application encounter errors. For the ARMv8 SEA/SEI, KVM or host kernel delivers SIGBUS to notify user space. After user space gets the notification, it will record the CPER to guest GHES buffer for guest and inject a exception or IRQ to guest. In the current implement, if the SIGBUS is BUS_MCEERR_AR, we will treat it as synchronous exception, and use ARMv8 SEA notification type to notify guest after recording CPER for guest; This series patches are based on Qemu 4.0, which have two parts: 1. Generate APEI/GHES table. 2. Handle the SIGBUS signal, record the CPER in runtime and fill into guest memory, then according to SIGBUS type to notify guest. Whole solution was suggested by James(james.morse@arm.com); APEI part solution is suggested by Laszlo(lersek@redhat.com). Shown some discussion in [1]. This series patches have already tested on ARM64 platform with RAS feature enabled: Show the APEI part verification result in [2] Show the BUS_MCEERR_AR SIGBUS handling verification result in [3] --- change since v16: 1. check whether ACPI table is enabled when handling the memory error in the SIGBUS handler. Change since v15: 1. Add a doc-comment in the proper format for 'include/exec/ram_addr.h' 2. Remove write_part_cpustate_to_list() because there is another bug fix patch has been merged "arm: Allow system registers for KVM guests to be changed by QEMU code" 3. Add some comments for kvm_inject_arm_sea() in 'target/arm/kvm64.c' 4. Compare the arm_current_el() return value to 0,1,2,3, not to PSTATE_MODE_* constants. 5. Change the RAS support wasn't introduced before 4.1 QEMU version. 6. Move the no_ras flag patch to begin in this series Change since v14: 1. Remove the BUS_MCEERR_AO handling logic because this asynchronous signal was masked by main thread 2. Address some Igor Mammedov's comments(ACPI part) 1) change the comments for the enum AcpiHestNotifyType definition and remove ditto in patch 1 2) change some patch commit messages and separate "APEI GHES table generation" patch to more patches. 3. Address some peter's comments(arm64 Synchronous External Abort injection) 1) change some code notes 2) using arm_current_el() for current EL 2) use the helper functions for those (syn_data_abort_*). Change since v13: 1. Move the patches that set guest ESR and inject virtual SError out of this series 2. Clean and optimize the APEI part patches 3. Update the commit messages and add some comments for the code Change since v12: 1. Address Paolo's comments to move HWPoisonPage definition to accel/kvm/kvm-all.c 2. Only call kvm_cpu_synchronize_state() when get the BUS_MCEERR_AR signal 3. Only add and enable GPIO-Signal and ARMv8 SEA two hardware error sources 4. Address Michael's comments to not sync SPDX from Linux kernel header file Change since v11: Address James's comments(james.morse@arm.com) 1. Check whether KVM has the capability to to set ESR instead of detecting host CPU RAS capability 2. For SIGBUS_MCEERR_AR SIGBUS, use Synchronous-External-Abort(SEA) notification type for SIGBUS_MCEERR_AO SIGBUS, use GPIO-Signal notification Address Shannon's comments(for ACPI part): 1. Unify hest_ghes.c and hest_ghes.h license declaration 2. Remove unnecessary including "qmp-commands.h" in hest_ghes.c 3. Unconditionally add guest APEI table based on James's comments(james.morse@arm.com) 4. Add a option to virt machine for migration compatibility. On new virt machine it's on by default while off for old ones, we enabled it since 2.12 5. Refer to the ACPI spec version which introduces Hardware Error Notification first time 6. Add ACPI_HEST_NOTIFY_RESERVED notification type Address Igor's comments(for ACPI part): 1. Add doc patch first which will describe how it's supposed to work between QEMU/firmware/guest OS with expected flows. 2. Move APEI diagrams into doc/spec patch 3. Remove redundant g_malloc in ghes_record_cper() 4. Use build_append_int_noprefix() API to compose whole error status block and whole APEI table, and try to get rid of most structures in patch 1, as they will be left unused after that 5. Reuse something like https://github.com/imammedo/qemu/commit/3d2fd6d13a3ea298d2ee814835495ce6241d085c to build GAS 6. Remove much offsetof() in the function 7. Build independent tables first and only then build dependent tables passing to it pointers to previously build table if necessary. 8. Redefine macro GHES_ACPI_HEST_NOTIFY_RESERVED to ACPI_HEST_ERROR_SOURCE_COUNT to avoid confusion Address Peter Maydell's comments 1. linux-headers is done as a patch of their own created using scripts/update-linux-headers.sh run against a mainline kernel tree 2. Tested whether this patchset builds OK on aarch32 3. Abstract Hwpoison page adding code out properly into a cpu-independent source file from target/i386/kvm.c, such as kvm-all.c 4. Add doc-comment formatted documentation comment for new globally-visible function prototype in a header --- [1]: https://lkml.org/lkml/2017/2/27/246 https://patchwork.kernel.org/patch/9633105/ https://patchwork.kernel.org/patch/9925227/ [2]: Note: the UEFI(QEMU_EFI.fd) is needed if guest want to use ACPI table. After guest boot up, dump the APEI table, then can see the initialized table (1) # iasl -p ./HEST -d /sys/firmware/acpi/tables/HEST (2) # cat HEST.dsl /* * Intel ACPI Component Architecture * AML/ASL+ Disassembler version 20170728 (64-bit version) * Copyright (c) 2000 - 2017 Intel Corporation * * Disassembly of /sys/firmware/acpi/tables/HEST, Mon Sep 5 07:59:17 2016 * * ACPI Data Table [HEST] * * Format: [HexOffset DecimalOffset ByteLength] FieldName : FieldValue */ .................................................................................. [308h 0776 2] Subtable Type : 000A [Generic Hardware Error Source V2] [30Ah 0778 2] Source Id : 0001 [30Ch 0780 2] Related Source Id : FFFF [30Eh 0782 1] Reserved : 00 [30Fh 0783 1] Enabled : 01 [310h 0784 4] Records To Preallocate : 00000001 [314h 0788 4] Max Sections Per Record : 00000001 [318h 0792 4] Max Raw Data Length : 00001000 [31Ch 0796 12] Error Status Address : [Generic Address Structure] [31Ch 0796 1] Space ID : 00 [SystemMemory] [31Dh 0797 1] Bit Width : 40 [31Eh 0798 1] Bit Offset : 00 [31Fh 0799 1] Encoded Access Width : 04 [QWord Access:64] [320h 0800 8] Address : 00000000785D0040 [328h 0808 28] Notify : [Hardware Error Notification Structure] [328h 0808 1] Notify Type : 08 [SEA] [329h 0809 1] Notify Length : 1C [32Ah 0810 2] Configuration Write Enable : 0000 [32Ch 0812 4] PollInterval : 00000000 [330h 0816 4] Vector : 00000000 [334h 0820 4] Polling Threshold Value : 00000000 [338h 0824 4] Polling Threshold Window : 00000000 [33Ch 0828 4] Error Threshold Value : 00000000 [340h 0832 4] Error Threshold Window : 00000000 [344h 0836 4] Error Status Block Length : 00001000 [348h 0840 12] Read Ack Register : [Generic Address Structure] [348h 0840 1] Space ID : 00 [SystemMemory] [349h 0841 1] Bit Width : 40 [34Ah 0842 1] Bit Offset : 00 [34Bh 0843 1] Encoded Access Width : 04 [QWord Access:64] [34Ch 0844 8] Address : 00000000785D0098 [354h 0852 8] Read Ack Preserve : 00000000FFFFFFFE [35Ch 0860 8] Read Ack Write : 0000000000000001 ..................................................................................... (3) After a synchronous external abort(SEA) happen, Qemu receive a SIGBUS and filled the CPER into guest GHES memory. For example, according to above table, the address that contains the physical address of a block of memory that holds the error status data for this abort is 0x00000000785D0040 (4) the address for SEA notification error source is 0x785d80b0 (qemu) xp /1 0x00000000785D0040 00000000785d0040: 0x785d80b0 (5) check the content of generic error status block and generic error data entry (qemu) xp /100x 0x785d80b0 00000000785d80b0: 0x00000001 0x00000000 0x00000000 0x00000098 00000000785d80c0: 0x00000000 0xa5bc1114 0x4ede6f64 0x833e63b8 00000000785d80d0: 0xb1837ced 0x00000000 0x00000300 0x00000050 00000000785d80e0: 0x00000000 0x00000000 0x00000000 0x00000000 00000000785d80f0: 0x00000000 0x00000000 0x00000000 0x00000000 00000000785d8100: 0x00000000 0x00000000 0x00000000 0x00004002 (6) check the OSPM's ACK value(for example SEA) /* Before OSPM acknowledges the error, check the ACK value */ (qemu) xp /1 0x00000000785D0098 00000000785d00f0: 0x00000000 /* After OSPM acknowledges the error, check the ACK value, it change to 1 from 0 */ (qemu) xp /1 0x00000000785D0098 00000000785d00f0: 0x00000001 [3]: KVM deliver "BUS_MCEERR_AR" to Qemu, Qemu record the guest CPER and inject synchronous external abort to notify guest, then guest do the recovery. [ 1552.516170] Synchronous External Abort: synchronous external abort (0x92000410) at 0x000000003751c6b4 [ 1553.074073] {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 8 [ 1553.081654] {1}[Hardware Error]: event severity: recoverable [ 1554.034191] {1}[Hardware Error]: Error 0, type: recoverable [ 1554.037934] {1}[Hardware Error]: section_type: memory error [ 1554.513261] {1}[Hardware Error]: physical_address: 0x0000000040fa6000 [ 1554.513944] {1}[Hardware Error]: error_type: 0, unknown [ 1555.041451] Memory failure: 0x40fa6: Killing mca-recover:1296 due to hardware memory corruption [ 1555.373116] Memory failure: 0x40fa6: recovery action for dirty LRU page: Recovered Dongjiu Geng (10): hw/arm/virt: Add RAS platform version for migration ACPI: add some GHES structures and macros definition acpi: add build_append_ghes_notify() helper for Hardware Error Notification acpi: add build_append_ghes_generic_data() helper for Generic Error Data Entry acpi: add build_append_ghes_generic_status() helper for Generic Error Status Block docs: APEI GHES generation and CPER record description ACPI: Add APEI GHES table generation support KVM: Move related hwpoison page functions to accel/kvm/ folder target-arm: kvm64: inject synchronous External Abort target-arm: kvm64: handle SIGBUS signal from kernel or KVM accel/kvm/kvm-all.c | 33 ++++ default-configs/arm-softmmu.mak | 1 + docs/specs/acpi_hest_ghes.txt | 97 +++++++++++ hw/acpi/Kconfig | 4 + hw/acpi/Makefile.objs | 1 + hw/acpi/acpi_ghes.c | 348 ++++++++++++++++++++++++++++++++++++++++ hw/acpi/aml-build.c | 70 ++++++++ hw/arm/virt-acpi-build.c | 12 ++ hw/arm/virt.c | 6 + include/exec/ram_addr.h | 24 +++ include/hw/acpi/acpi-defs.h | 52 ++++++ include/hw/acpi/acpi_ghes.h | 83 ++++++++++ include/hw/acpi/aml-build.h | 21 +++ include/hw/arm/virt.h | 1 + include/sysemu/kvm.h | 2 +- target/arm/internals.h | 5 +- target/arm/kvm.c | 3 + target/arm/kvm64.c | 73 +++++++++ target/arm/op_helper.c | 2 +- target/i386/kvm.c | 34 +--- 20 files changed, 835 insertions(+), 37 deletions(-) create mode 100644 docs/specs/acpi_hest_ghes.txt create mode 100644 hw/acpi/acpi_ghes.c create mode 100644 include/hw/acpi/acpi_ghes.h