diff mbox series

[v13,2/4] arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit

Message ID 20190520142330.3556-3-angus@akkea.ca (mailing list archive)
State New, archived
Headers show
Series Add support for the Purism Librem5 devkit | expand

Commit Message

Angus Ainslie May 20, 2019, 2:23 p.m. UTC
This is for the development kit board for the Librem 5. The current level
of support yields a working console and is able to boot userspace from
the network or eMMC.

Additional subsystems that are active :

- Both USB ports
- SD card socket
- WiFi usdhc
- WWAN modem
- GNSS
- GPIO keys
- LEDs
- gyro
- magnetometer
- touchscreen
- pwm
- backlight
- haptic motor

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mq-librem5-devkit.dts   | 810 ++++++++++++++++++
 2 files changed, 811 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts

Comments

Pavel Machek May 23, 2019, 7:19 p.m. UTC | #1
Hi!

> This is for the development kit board for the Librem 5. The current level
> of support yields a working console and is able to boot userspace from
> the network or eMMC.
> 
> Additional subsystems that are active :

> - haptic motor

Haptic motor is not a LED. It should be controlled by input subsystem.

> +	pwmleds {
> +		compatible = "pwm-leds";
> +
> +		haptic {
> +			label = "librem5::haptic";
> +			pwms = <&pwm2 0 200000>;
> +			active-low;
> +			max-brightness = <255>;
> +			power-supply = <&reg_3v3_p>;
> +		};
> +	};

You can take a look at N900, that has reasonable interface.

Thanks,
										Pavel
Pavel Machek May 23, 2019, 7:19 p.m. UTC | #2
Hi!

> - LEDs
> - gyro
> - magnetometer

> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> +		led1 {
> +			label = "LED 1";

So, what kind of LED do you have, and what color is it? label should probably be something like
notify:green.

> +	charger@6b { /* bq25896 */
> +		compatible = "ti,bq25890";
> +		reg = <0x6b>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_charger>;
> +		interrupt-parent = <&gpio3>;
> +		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> +		ti,battery-regulation-voltage = <4192000>; /* 4.192V */
> +		ti,charge-current = <1600000>; /* 1.6 A */

No space before A, for consistency.

> +		ti,termination-current = <66000>;  /* 66mA */
> +		ti,precharge-current = <1300000>; /* 1.3A */

I thought precharge is usually something low, because you are not yet sure of battery health...?

> +		ti,minimum-sys-voltage = <2750000>; /* 2.75V */

Are you sure? Normally systems shut down at 3.2V, 3V or so. Li-ion batteries don't
really like to be discharged _this_ deep.

										Pavel
Angus Ainslie May 23, 2019, 9:52 p.m. UTC | #3
Hi Pavel,


On 2019-05-23 12:19, Pavel Machek wrote:
> Hi!
> 
>> This is for the development kit board for the Librem 5. The current 
>> level
>> of support yields a working console and is able to boot userspace from
>> the network or eMMC.
>> 
>> Additional subsystems that are active :
> 
>> - haptic motor
> 
> Haptic motor is not a LED. It should be controlled by input subsystem.
> 
>> +	pwmleds {
>> +		compatible = "pwm-leds";
>> +
>> +		haptic {
>> +			label = "librem5::haptic";
>> +			pwms = <&pwm2 0 200000>;
>> +			active-low;
>> +			max-brightness = <255>;
>> +			power-supply = <&reg_3v3_p>;
>> +		};
>> +	};
> 
> You can take a look at N900, that has reasonable interface.
> 

I wanted to control the haptic with the pwm-vibra driver but 
"fsl,imx27-pwm" doesn't seem to respect the PWM_POLARITY_INVERTED flag 
so when I start the system the vibrator is full on.

I could use gpio-vibrator but that seemed like a waste when the device 
is connected to pwm.

I figured the using the pwm-leds interface was a reasonable compromise 
until I had an opportunity to make changes the the imx27-pwm driver.

Thanks
Angus


> Thanks,
> 										Pavel
Pavel Machek May 23, 2019, 10:06 p.m. UTC | #4
Hi!

> >>This is for the development kit board for the Librem 5. The current
> >>level
> >>of support yields a working console and is able to boot userspace from
> >>the network or eMMC.
> >>
> >>Additional subsystems that are active :
> >
> >>- haptic motor
> >
> >Haptic motor is not a LED. It should be controlled by input subsystem.
> >
> >>+	pwmleds {
> >>+		compatible = "pwm-leds";
> >>+
> >>+		haptic {
> >>+			label = "librem5::haptic";
> >>+			pwms = <&pwm2 0 200000>;
> >>+			active-low;
> >>+			max-brightness = <255>;
> >>+			power-supply = <&reg_3v3_p>;
> >>+		};
> >>+	};
> >
> >You can take a look at N900, that has reasonable interface.
> 
> I wanted to control the haptic with the pwm-vibra driver but "fsl,imx27-pwm"
> doesn't seem to respect the PWM_POLARITY_INVERTED flag so when I start the
> system the vibrator is full on.

Ok, lets fix that :-).

> I could use gpio-vibrator but that seemed like a waste when the device is
> connected to pwm.
> 
> I figured the using the pwm-leds interface was a reasonable compromise until
> I had an opportunity to make changes the the imx27-pwm driver.

I guess in such case it would be best to leave out this section for
now... or keep it disabled / something. We don't want incorrect device
trees to stick around.

Thanks,
									Pavel
Angus Ainslie May 24, 2019, 10 p.m. UTC | #5
Hi Pavel,

On 2019-05-23 12:19, Pavel Machek wrote:
> Hi!
> 
>> - LEDs
>> - gyro
>> - magnetometer
> 
>> +	leds {
>> +		compatible = "gpio-leds";
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pinctrl_gpio_leds>;
>> +
>> +		led1 {
>> +			label = "LED 1";
> 
> So, what kind of LED do you have, and what color is it? label should
> probably be something like
> notify:green.
> 

As we don't have a specific use for these yet does it really matter if 
there is a colour or a number associated with them ?

>> +	charger@6b { /* bq25896 */
>> +		compatible = "ti,bq25890";
>> +		reg = <0x6b>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pinctrl_charger>;
>> +		interrupt-parent = <&gpio3>;
>> +		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
>> +		ti,battery-regulation-voltage = <4192000>; /* 4.192V */
>> +		ti,charge-current = <1600000>; /* 1.6 A */
> 
> No space before A, for consistency.
> 
>> +		ti,termination-current = <66000>;  /* 66mA */
>> +		ti,precharge-current = <1300000>; /* 1.3A */
> 
> I thought precharge is usually something low, because you are not yet
> sure of battery health...?
> 

I think I put that in incorrectly. The intention was 130mA.

>> +		ti,minimum-sys-voltage = <2750000>; /* 2.75V */
> 
> Are you sure? Normally systems shut down at 3.2V, 3V or so. Li-ion
> batteries don't
> really like to be discharged _this_ deep.

You are correct. I'll fix it for the next version.

Thanks
Angus

> 
> 										Pavel
Angus Ainslie May 24, 2019, 10:20 p.m. UTC | #6
Hi Pavel,

On 2019-05-24 15:00, Angus Ainslie wrote:
> Hi Pavel,
> 
> On 2019-05-23 12:19, Pavel Machek wrote:
>> Hi!
>> 
>>> - LEDs
>>> - gyro
>>> - magnetometer
>> 
>>> +	leds {
>>> +		compatible = "gpio-leds";
>>> +		pinctrl-names = "default";
>>> +		pinctrl-0 = <&pinctrl_gpio_leds>;
>>> +
>>> +		led1 {
>>> +			label = "LED 1";
>> 
>> So, what kind of LED do you have, and what color is it? label should
>> probably be something like
>> notify:green.
>> 
> 
> As we don't have a specific use for these yet does it really matter if
> there is a colour or a number associated with them ?
> 
>>> +	charger@6b { /* bq25896 */
>>> +		compatible = "ti,bq25890";
>>> +		reg = <0x6b>;
>>> +		pinctrl-names = "default";
>>> +		pinctrl-0 = <&pinctrl_charger>;
>>> +		interrupt-parent = <&gpio3>;
>>> +		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
>>> +		ti,battery-regulation-voltage = <4192000>; /* 4.192V */
>>> +		ti,charge-current = <1600000>; /* 1.6 A */
>> 
>> No space before A, for consistency.
>> 
>>> +		ti,termination-current = <66000>;  /* 66mA */
>>> +		ti,precharge-current = <1300000>; /* 1.3A */
>> 
>> I thought precharge is usually something low, because you are not yet
>> sure of battery health...?
>> 
> 
> I think I put that in incorrectly. The intention was 130mA.
> 
>>> +		ti,minimum-sys-voltage = <2750000>; /* 2.75V */
>> 
>> Are you sure? Normally systems shut down at 3.2V, 3V or so. Li-ion
>> batteries don't
>> really like to be discharged _this_ deep.
> 
> You are correct. I'll fix it for the next version.
> 

Looking into it further Sanyo and Panasonic get over 300 cycles bringing 
the NCR18650 down to 2.5V so 2.75V should be fine.

http://www.batteryonestop.com/baotongusa/products/datasheets/li-ion/SANYO-NCR18650B-3400mAh.pdf
https://industrial.panasonic.com/ww/products/batteries/secondary-batteries/lithium-ion/cylindrical-type/NCR18650PF

Angus

> Thanks
> Angus
> 
>> 
>> 										Pavel
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 0bd122f60549..c043aca66572 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -22,6 +22,7 @@  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
 
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
new file mode 100644
index 000000000000..e77cab22cbe0
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -0,0 +1,810 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018-2019 Purism SPC
+ */
+
+/dts-v1/;
+
+#include "dt-bindings/input/input.h"
+#include "dt-bindings/usb/pd.h"
+#include "imx8mq.dtsi"
+
+/ {
+	model = "Purism Librem 5 devkit";
+	compatible = "purism,librem5-devkit", "fsl,imx8mq";
+
+	backlight_dsi: backlight-dsi {
+		compatible = "pwm-backlight";
+		/* 200 Hz for the PAM2841 */
+		pwms = <&pwm1 0 5000000>;
+		brightness-levels = <0 100>;
+		num-interpolated-steps = <100>;
+		/* Default brightness level (index into the array defined by */
+		/* the "brightness-levels" property) */
+		default-brightness-level = <0>;
+		power-supply = <&reg_22v4_p>;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		btn1 {
+			label = "VOL_UP";
+			gpios = <&gpio4 21 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		btn2 {
+			label = "VOL_DOWN";
+			gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		hp_det {
+			label = "HP_DET";
+			gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+			linux,code = <KEY_HP>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led1 {
+			label = "LED 1";
+			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	pmic_osc: pmic-osc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic_osc";
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+
+		haptic {
+			label = "librem5::haptic";
+			pwms = <&pwm2 0 200000>;
+			active-low;
+			max-brightness = <255>;
+			power-supply = <&reg_3v3_p>;
+		};
+	};
+
+	reg_1v8_p: regulator-1v8-p {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8_p";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&reg_pwr_en>;
+	};
+
+	reg_2v8_p: regulator-2v8-p {
+		compatible = "regulator-fixed";
+		regulator-name = "2v8_p";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_pwr_en>;
+	};
+
+	reg_3v3_p: regulator-3v3-p {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3_p";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_pwr_en>;
+		regulator-state-mem {
+			regulator-on-in-suspend;
+		};
+	};
+
+	reg_5v_p: regulator-5v-p {
+		compatible = "regulator-fixed";
+		regulator-name = "5v_p";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_pwr_en>;
+		regulator-state-mem {
+			regulator-on-in-suspend;
+		};
+	};
+
+	reg_22v4_p: regulator-22v4-p {
+		compatible = "regulator-fixed";
+		regulator-name = "22v4_P";
+		regulator-min-microvolt = <22400000>;
+		regulator-max-microvolt = <22400000>;
+		vin-supply = <&reg_pwr_en>;
+	};
+
+	reg_pwr_en: regulator-pwr-en {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pwr_en>;
+		regulator-name = "PWR_EN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_pwr>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	wifi_pwr_en: wifi-en {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pwr_en>;
+		regulator-name = "WIFI_EN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+};
+
+&clk {
+	assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>;
+	assigned-clock-rates = <786432000>, <722534400>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	phy-supply = <&reg_3v3_p>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pmic: pmic@4b {
+		compatible = "rohm,bd71837";
+		reg = <0x4b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		clocks = <&pmic_osc>;
+		clock-names = "osc";
+		clock-output-names = "pmic_clk";
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupt-names = "irq";
+		rohm,reset-snvs-powered;
+
+		regulators {
+
+			buck1_reg: BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <900000>;
+				rohm,dvs-idle-voltage = <850000>;
+				rohm,dvs-suspend-voltage = <800000>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <1000000>;
+				rohm,dvs-idle-voltage = <900000>;
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				rohm,dvs-run-voltage = <1000000>;
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				rohm,dvs-run-voltage = <1000000>;
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "buck6";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+			};
+
+			buck7_reg: BUCK7 {
+				regulator-name = "buck7";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+			};
+
+			buck8_reg: BUCK8 {
+				regulator-name = "buck8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-name = "ldo5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+			};
+
+			ldo7_reg: LDO7 {
+				regulator-name = "ldo7";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+			};
+		};
+	};
+
+	typec_ptn5100: usb_typec@52 {
+		compatible = "nxp,ptn5110";
+		reg = <0x52>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_typec>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			data-role = "dual";
+			power-role = "dual";
+			try-power-role = "sink";
+			source-pdos = <PDO_FIXED(5000, 2000,
+				PDO_FIXED_USB_COMM |
+				PDO_FIXED_DUAL_ROLE |
+				PDO_FIXED_DATA_SWAP )>;
+			sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM |
+				PDO_FIXED_DUAL_ROLE |
+				PDO_FIXED_DATA_SWAP )
+			     PDO_VAR(5000, 12000, 2000)>;
+			op-sink-microwatt = <10000000>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					usb_con_hs: endpoint {
+						remote-endpoint = <&typec_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					usb_con_ss: endpoint {
+						remote-endpoint = <&typec_ss>;
+					};
+				};
+			};
+		};
+	};
+
+	rtc@68 {
+		compatible = "microcrystal,rv4162";
+		reg = <0x68>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	charger@6b { /* bq25896 */
+		compatible = "ti,bq25890";
+		reg = <0x6b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_charger>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		ti,battery-regulation-voltage = <4192000>; /* 4.192V */
+		ti,charge-current = <1600000>; /* 1.6 A */
+		ti,termination-current = <66000>;  /* 66mA */
+		ti,precharge-current = <1300000>; /* 1.3A */
+		ti,minimum-sys-voltage = <2750000>; /* 2.75V */
+		ti,boost-voltage = <5000000>; /* 5V */
+		ti,boost-max-current = <50000>; /* 50mA */
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	magnetometer@1e	{
+		compatible = "st,lsm9ds1-magn";
+		reg = <0x1e>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_imu>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&reg_3v3_p>;
+		vddio-supply = <&reg_3v3_p>;
+	};
+
+	touchscreen@5d {
+		compatible = "goodix,gt5688";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_goodix_ts>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		irq-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1440>;
+		AVDD28-supply = <&reg_2v8_p>;
+		VDDIO-supply = <&reg_1v8_p>;
+	};
+};
+
+&iomuxc {
+	pinctrl_backlight: pwm1 {
+		fsl,pins = <
+		MX8MQ_IOMUXC_GPIO1_IO01_PWM1_OUT	0x6  /* DSI_BL_PWM */
+		>;
+	};
+
+	pinctrl_bt: btgrp {
+		fsl,pins = <
+		/* nBT_DISABLE */
+		MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11             0x16
+		/* BT_HOST_WAKE */
+		MX8MQ_IOMUXC_NAND_DATA01_GPIO3_IO7              0x10
+		>;
+	};
+
+	pinctrl_charger: chargernirq {
+		fsl,pins = <
+		/* CHRG_nINT */
+		MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25	0x80
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC		0x3
+		MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO	0x3
+		MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x1f
+		MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x1f
+		MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x1f
+		MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x1f
+		MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x91
+		MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x91
+		MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x91
+		MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x91
+		MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f
+		MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91
+		MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+		MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+		MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x19
+		MX8MQ_IOMUXC_GPIO1_IO15_CCMSRCGPCMIX_CLKO2      0x1f
+		>;
+	};
+
+	pinctrl_goodix_ts: gt5688 {
+		fsl,pins = <
+		/* TOUCH INT */
+		MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0         0x16
+		/* TOUCH RST */
+		MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5	0x19
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioleds {
+		fsl,pins = <
+		MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x16
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeys {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21	0x16
+		MX8MQ_IOMUXC_SAI2_RXC_GPIO4_IO22	0x16
+		/* HP_DET */
+		MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20	0x180
+		>;
+	};
+
+	pinctrl_haptic: hapticgrp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SPDIF_RX_PWM2_OUT		0xc6  /* nHAPTIC */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL		0x4000001f
+		MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA		0x4000001f
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL		0x4000001f
+		MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA		0x4000001f
+		>;
+	};
+
+	pinctrl_imu: imugrp {
+		fsl,pins = <
+		/* IMU_INT */
+		MX8MQ_IOMUXC_SAI5_RXFS_GPIO3_IO19	0x8
+		>;
+	};
+
+	pinctrl_pmic: pmicint {
+		fsl,pins = <
+		MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x80
+		>;
+	};
+
+	pinctrl_pwr_en: pwrengrp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8               0x06
+		>;
+	};
+
+	pinctrl_rtc: rtcirq {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29	0x80
+		>;
+	};
+
+	pinctrl_typec: typecgrp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12	0x16
+		MX8MQ_IOMUXC_NAND_CE0_B_GPIO3_IO1	0x80
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x49
+		MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX		0x49
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x49
+		MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX		0x49
+		MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B		0x49
+		MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B		0x49
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX		0x49
+		MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX		0x49
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX		0x49
+		MX8MQ_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX		0x49
+		MX8MQ_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B	0x49
+		MX8MQ_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B		0x49
+		MX8MQ_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K	0x49
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
+		MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc3
+		MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc3
+		MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc3
+		MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc3
+		MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc3
+		MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc3
+		MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc3
+		MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc3
+		MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc3
+		MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x83
+		MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x8d
+		MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xcd
+		MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xcd
+		MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xcd
+		MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xcd
+		MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xcd
+		MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xcd
+		MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xcd
+		MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xcd
+		MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xcd
+		MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x8d
+		MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x9f
+		MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xdf
+		MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xdf
+		MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xdf
+		MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xdf
+		MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xdf
+		MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xdf
+		MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xdf
+		MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xdf
+		MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xdf
+		MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x9f
+		MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_pwr: usdhc2grppwr {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x41
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+		fsl,pins = <
+		/* WIFI_WAKE */
+		MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20			0x80
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
+		MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
+		MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3
+		MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc3
+		MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc3
+		MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc3
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x8d
+		MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xcd
+		MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xcd
+		MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xcd
+		MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xcd
+		MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xcd
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x9f
+		MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xcf
+		MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xcf
+		MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xcf
+		MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xcf
+		MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xcf
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0xc6
+		>;
+	};
+
+	pinctrl_wifi_pwr_en: wifipwrengrp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5         0x06
+		>;
+	};
+
+	pinctrl_wwan: wwangrp {
+		fsl,pins = <
+		/* nWWAN_DISABLE */
+		MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4	0x09
+		/* nWoWWAN */
+		MX8MQ_IOMUXC_NAND_DATA02_GPIO3_IO8	0x80
+		/* WWAN_RESET */
+		MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9	0x19
+		>;
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_backlight>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_haptic>;
+	status = "okay";
+};
+
+&uart1 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 { /* GNSS */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 { /* BT */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>, <&pinctrl_bt>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+&usb3_phy1 {
+	vbus-supply = <&reg_5v_p>;
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	dr_mode = "otg";
+	status = "okay";
+
+	port@0 {
+		reg = <0>;
+
+		typec_hs: endpoint {
+			remote-endpoint = <&usb_con_hs>;
+		};
+	};
+
+	port@1 {
+		reg = <1>;
+
+		typec_ss: endpoint {
+			remote-endpoint = <&usb_con_ss>;
+		};
+	};
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	power-supply = <&wifi_pwr_en>;
+	non-removable;
+	disable-wp;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};