| Message ID | 20190524181936.29470-2-martin.blumenstingl@googlemail.com (mailing list archive) |
|---|---|
| State | Mainlined |
| Commit | d94f60e3dfa0ac72aaa82352652ed76cece4d9ab |
| Headers | show |
| Series | ARM: meson8b-mxq: better support for the TRONFY MXQ | expand |
On Fri, May 24, 2019 at 8:19 PM Martin Blumenstingl <martin.blumenstingl@googlemail.com> wrote: > > The TRONFY MXQ comes with either 1GB or 2GB RAM. > > Both variants share (like most boards based on Amlogic reference > designs): > - 10/100 PHY (IC Plus IP101GR) with GPIOH_4 being the reset line and > GPIOH_3 the interrupt line > - SD card slot with the card detection GPIO at CARD_6 > - VCCK is generated by PWM_C with a period of 1148ns and XTAL as input > clock > - USB OTG exposed on one of the USB-A connectors > - 4-port USB hub with 3 ports exposed to the outside > > There seem the multiple board revision out there according to various > forum posts: > - storage: eMMC or NAND flash > - wifi: Ampak AP6210 or Realtek 8189 > > Add support for the following functionality: > - SoC temperature (hwmon) > - changing the CPU voltage > - Ethernet connectivity > - SD card > - USB > > Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: hexdump <hexdump0815@googlemail.com> BEFORE (no patches from this series applied): the mxq device was not really useable with the old mainline dtb as most peripeherals were not supported AFTER (the patch applied): the rresulting dtb works perfectly fine with my mxq device and all mentioned supported functions work as expected best wishes - hexdump
hex dump <hexdump0815@gmail.com> writes: > Am Fr., 24. Mai 2019 um 20:19 Uhr schrieb Martin Blumenstingl < > martin.blumenstingl@googlemail.com>: > >> The TRONFY MXQ comes with either 1GB or 2GB RAM. >> >> Both variants share (like most boards based on Amlogic reference >> designs): >> - 10/100 PHY (IC Plus IP101GR) with GPIOH_4 being the reset line and >> GPIOH_3 the interrupt line >> - SD card slot with the card detection GPIO at CARD_6 >> - VCCK is generated by PWM_C with a period of 1148ns and XTAL as input >> clock >> - USB OTG exposed on one of the USB-A connectors >> - 4-port USB hub with 3 ports exposed to the outside >> >> There seem the multiple board revision out there according to various >> forum posts: >> - storage: eMMC or NAND flash >> - wifi: Ampak AP6210 or Realtek 8189 >> >> Add support for the following functionality: >> - SoC temperature (hwmon) >> - changing the CPU voltage >> - Ethernet connectivity >> - SD card >> - USB >> >> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> >> > > Tested-by: hexdump <hexdump0815@googlemail.com> Thanks for testing. Queued for v5,3, Kevin
diff --git a/arch/arm/boot/dts/meson8b-mxq.dts b/arch/arm/boot/dts/meson8b-mxq.dts index 08ddd7fb0bf8..07f1cc513f8a 100644 --- a/arch/arm/boot/dts/meson8b-mxq.dts +++ b/arch/arm/boot/dts/meson8b-mxq.dts @@ -45,6 +45,9 @@ */ /dts-v1/; + +#include <dt-bindings/gpio/gpio.h> + #include "meson8b.dtsi" / { @@ -63,6 +66,126 @@ device_type = "memory"; reg = <0x40000000 0x40000000>; }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&saradc 8>; + }; + + vcck: regulator-vcck { + compatible = "pwm-regulator"; + + regulator-name = "VCCK"; + regulator-min-microvolt = <860000>; + regulator-max-microvolt = <1140000>; + + pwms = <&pwm_cd 0 1148 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + + vcc_1v8: regulator-vcc1v8 { + compatible = "regulator-fixed"; + + regulator-name = "VCC1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + vin-supply = <&vcc_3v3>; + }; + + vcc_3v3: regulator-vcc3v3 { + compatible = "regulator-fixed"; + + regulator-name = "VCC3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + vin-supply = <&vcc_5v>; + }; + + vcc_5v: regulator-vcc5v { + compatible = "regulator-fixed"; + + regulator-name = "VCC5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + regulator-boot-on; + regulator-always-on; + }; +}; + +&cpu0 { + cpu-supply = <&vcck>; +}; + +ðmac { + status = "okay"; + + pinctrl-0 = <ð_rmii_pins>; + pinctrl-names = "default"; + + phy-handle = <ð_phy0>; + phy-mode = "rmii"; + + snps,reset-gpio = <&gpio GPIOH_4 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + eth_phy0: ethernet-phy@0 { + /* IC Plus IP101A/G (0x02430c54) */ + reg = <0>; + icplus,select-interrupt; + interrupt-parent = <&gpio_intc>; + /* GPIOH_3 */ + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + }; + }; +}; + +&saradc { + status = "okay"; + vref-supply = <&vcc_1v8>; +}; + +&sdio { + status = "okay"; + + pinctrl-0 = <&sd_b_pins>; + pinctrl-names = "default"; + + /* SD card */ + sd_card_slot: slot@1 { + compatible = "mmc-slot"; + reg = <1>; + status = "okay"; + + bus-width = <4>; + no-sdio; + cap-mmc-highspeed; + cap-sd-highspeed; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>; + + vmmc-supply = <&vcc_3v3>; + }; +}; + +&pwm_cd { + status = "okay"; + pinctrl-0 = <&pwm_c1_pins>; + pinctrl-names = "default"; + clocks = <&clkc CLKID_XTAL>; + clock-names = "clkin0"; }; &uart_AO { @@ -70,3 +193,19 @@ pinctrl-0 = <&uart_ao_a_pins>; pinctrl-names = "default"; }; + +&usb0 { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +};
The TRONFY MXQ comes with either 1GB or 2GB RAM. Both variants share (like most boards based on Amlogic reference designs): - 10/100 PHY (IC Plus IP101GR) with GPIOH_4 being the reset line and GPIOH_3 the interrupt line - SD card slot with the card detection GPIO at CARD_6 - VCCK is generated by PWM_C with a period of 1148ns and XTAL as input clock - USB OTG exposed on one of the USB-A connectors - 4-port USB hub with 3 ports exposed to the outside There seem the multiple board revision out there according to various forum posts: - storage: eMMC or NAND flash - wifi: Ampak AP6210 or Realtek 8189 Add support for the following functionality: - SoC temperature (hwmon) - changing the CPU voltage - Ethernet connectivity - SD card - USB Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> --- arch/arm/boot/dts/meson8b-mxq.dts | 139 ++++++++++++++++++++++++++++++ 1 file changed, 139 insertions(+)