| Message ID | 20190619102454.5097-1-faiz_abbas@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | ARM: dts: am57xx: Disable voltage switching for SD card | expand |
* Faiz Abbas <faiz_abbas@ti.com> [190619 03:25]: > If UHS speed modes are enabled, a compatible SD card switches down to > 1.8V during enumeration. If after this a software reboot/crash takes > place and on-chip ROM tries to enumerate the SD card, the difference in > IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card. > > The fix for this is to have support for power cycling the card in > hardware (with a PORz/soft-reset line causing a power cycle of the > card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and > am57xx-evms don't have this capability, disable voltage switching for > these boards. > > The major effect of this is that the maximum supported speed > mode is now high speed(50 MHz) down from SDR104(200 MHz). > > commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage > switching for SD card") did this only for idk boards. Do it for all > affected boards. Thanks applying into fixes. Regards, Tony
diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts index 66116ad3f9f4..0a043908215c 100644 --- a/arch/arm/boot/dts/am571x-idk.dts +++ b/arch/arm/boot/dts/am571x-idk.dts @@ -178,14 +178,9 @@ }; &mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; }; &mmc2 { diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts index 4f835222c266..8663a9416af6 100644 --- a/arch/arm/boot/dts/am572x-idk.dts +++ b/arch/arm/boot/dts/am572x-idk.dts @@ -19,14 +19,9 @@ }; &mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; }; &mmc2 { diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts index dc5141c35610..7935d70874ce 100644 --- a/arch/arm/boot/dts/am574x-idk.dts +++ b/arch/arm/boot/dts/am574x-idk.dts @@ -24,14 +24,9 @@ }; &mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_default>; - pinctrl-3 = <&mmc1_pins_hs>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_conf>; - pinctrl-6 = <&mmc1_pins_ddr50 &mmc1_iodelay_sdr104_conf>; }; &mmc2 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi index 2341a56ebab9..0cdfd2853ba8 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi @@ -433,6 +433,7 @@ bus-width = <4>; cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */ + no-1-8-v; }; &mmc2 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts index 5a77b334923d..34c69965821b 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts @@ -19,14 +19,9 @@ }; &mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>; vmmc-supply = <&vdd_3v3>; vqmmc-supply = <&ldo1_reg>; }; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts index 17c41da3b55f..ccd99160bbdf 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts @@ -19,14 +19,9 @@ }; &mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; vmmc-supply = <&vdd_3v3>; vqmmc-supply = <&ldo1_reg>; };
If UHS speed modes are enabled, a compatible SD card switches down to 1.8V during enumeration. If after this a software reboot/crash takes place and on-chip ROM tries to enumerate the SD card, the difference in IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card. The fix for this is to have support for power cycling the card in hardware (with a PORz/soft-reset line causing a power cycle of the card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and am57xx-evms don't have this capability, disable voltage switching for these boards. The major effect of this is that the maximum supported speed mode is now high speed(50 MHz) down from SDR104(200 MHz). commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage switching for SD card") did this only for idk boards. Do it for all affected boards. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> --- arch/arm/boot/dts/am571x-idk.dts | 7 +------ arch/arm/boot/dts/am572x-idk.dts | 7 +------ arch/arm/boot/dts/am574x-idk.dts | 7 +------ arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 1 + arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts | 7 +------ arch/arm/boot/dts/am57xx-beagle-x15-revc.dts | 7 +------ 6 files changed, 6 insertions(+), 30 deletions(-)