@@ -6095,6 +6095,15 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
}
/*
+ * Clear encryption initialization vectors on start, but keep them
+ * for watchdog reset. Otherwise we will have wrong IVs and not be
+ * able to keep connections after reset.
+ */
+ if (!test_bit(DEVICE_STATE_RESET, &rt2x00dev->flags))
+ for (i = 0; i < 256; i++)
+ rt2800_register_write(rt2x00dev, MAC_IVEIV_ENTRY(i), 0);
+
+ /*
* Clear all beacons
*/
for (i = 0; i < 8; i++)
@@ -659,6 +659,7 @@ enum rt2x00_state_flags {
DEVICE_STATE_ENABLED_RADIO,
DEVICE_STATE_SCANNING,
DEVICE_STATE_FLUSHING,
+ DEVICE_STATE_RESET,
/*
* Driver configuration
@@ -1253,13 +1253,14 @@ static int rt2x00lib_initialize(struct rt2x00_dev *rt2x00dev)
int rt2x00lib_start(struct rt2x00_dev *rt2x00dev)
{
- int retval;
+ int retval = 0;
if (test_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags)) {
/*
* This is special case for ieee80211_restart_hw(), otherwise
* mac80211 never call start() two times in row without stop();
*/
+ set_bit(DEVICE_STATE_RESET, &rt2x00dev->flags);
rt2x00dev->ops->lib->pre_reset_hw(rt2x00dev);
rt2x00lib_stop(rt2x00dev);
}
@@ -1270,14 +1271,14 @@ int rt2x00lib_start(struct rt2x00_dev *rt2x00dev)
*/
retval = rt2x00lib_load_firmware(rt2x00dev);
if (retval)
- return retval;
+ goto out;
/*
* Initialize the device.
*/
retval = rt2x00lib_initialize(rt2x00dev);
if (retval)
- return retval;
+ goto out;
rt2x00dev->intf_ap_count = 0;
rt2x00dev->intf_sta_count = 0;
@@ -1286,11 +1287,13 @@ int rt2x00lib_start(struct rt2x00_dev *rt2x00dev)
/* Enable the radio */
retval = rt2x00lib_enable_radio(rt2x00dev);
if (retval)
- return retval;
+ goto out;
set_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags);
- return 0;
+out:
+ clear_bit(DEVICE_STATE_RESET, &rt2x00dev->flags);
+ return retval;
}
void rt2x00lib_stop(struct rt2x00_dev *rt2x00dev)
To do not brake HW restart we should keep initialization vectors data. I assumed that on start the data is already initialized to zeros, but that not true on some scenarios and we should clear it. So add additional flag to check if we are under HW restart and clear IV's data if we are not. Patch fixes AP mode regression. Reported-and-tested-by: Emil Karlson <jekarl@iki.fi> Fixes: 710e6cc1595e ("rt2800: do not nullify initialization vector data") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> --- drivers/net/wireless/ralink/rt2x00/rt2800lib.c | 9 +++++++++ drivers/net/wireless/ralink/rt2x00/rt2x00.h | 1 + drivers/net/wireless/ralink/rt2x00/rt2x00dev.c | 13 ++++++++----- 3 files changed, 18 insertions(+), 5 deletions(-)