Message ID | 20190822151904.17919-5-ramalingam.c@intel.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Series | drm/i915: Enable HDCP 1.4 and 2.2 on Gen12+ | expand |
Regards Shashank On 8/22/2019 8:49 PM, Ramalingam C wrote: > For gen12+ platform we need to pass the transcoder info > as part of the port info into ME FW. > > This change fills the payload for ME FW from hdcp_port_data. > > Signed-off-by: Ramalingam C <ramalingam.c@intel.com> > Acked-by: Jani Nikula <jani.nikula@intel.com> > --- > drivers/misc/mei/hdcp/mei_hdcp.c | 11 +++++++++++ > drivers/misc/mei/hdcp/mei_hdcp.h | 4 +++- > 2 files changed, 14 insertions(+), 1 deletion(-) > > diff --git a/drivers/misc/mei/hdcp/mei_hdcp.c b/drivers/misc/mei/hdcp/mei_hdcp.c > index 3638c77eba26..93027fd96c71 100644 > --- a/drivers/misc/mei/hdcp/mei_hdcp.c > +++ b/drivers/misc/mei/hdcp/mei_hdcp.c > @@ -58,6 +58,7 @@ mei_hdcp_initiate_session(struct device *dev, struct hdcp_port_data *data, > > session_init_in.port.integrated_port_type = data->port_type; > session_init_in.port.physical_port = (u8)data->fw_ddi; As this entry is only valid till GEN11.5, don't we need GEN_CHECK here, say (INTEL_GEN() < 12). Is that possible in MEI_FW ? If not, probably we have to add this gen_check while filling the fw_tc part in I915. Applies for all the changes below too. - Shashank > + session_init_in.port.attached_transcoder = (u8)data->fw_tc; > session_init_in.protocol = data->protocol; > > byte = mei_cldev_send(cldev, (u8 *)&session_init_in, > @@ -127,6 +128,7 @@ mei_hdcp_verify_receiver_cert_prepare_km(struct device *dev, > > verify_rxcert_in.port.integrated_port_type = data->port_type; > verify_rxcert_in.port.physical_port = (u8)data->fw_ddi; > + verify_rxcert_in.port.attached_transcoder = (u8)data->fw_tc; > > verify_rxcert_in.cert_rx = rx_cert->cert_rx; > memcpy(verify_rxcert_in.r_rx, &rx_cert->r_rx, HDCP_2_2_RRX_LEN); > @@ -197,6 +199,7 @@ mei_hdcp_verify_hprime(struct device *dev, struct hdcp_port_data *data, > > send_hprime_in.port.integrated_port_type = data->port_type; > send_hprime_in.port.physical_port = (u8)data->fw_ddi; > + send_hprime_in.port.attached_transcoder = (u8)data->fw_tc; > > memcpy(send_hprime_in.h_prime, rx_hprime->h_prime, > HDCP_2_2_H_PRIME_LEN); > @@ -254,6 +257,7 @@ mei_hdcp_store_pairing_info(struct device *dev, struct hdcp_port_data *data, > > pairing_info_in.port.integrated_port_type = data->port_type; > pairing_info_in.port.physical_port = (u8)data->fw_ddi; > + pairing_info_in.port.attached_transcoder = (u8)data->fw_tc; > > memcpy(pairing_info_in.e_kh_km, pairing_info->e_kh_km, > HDCP_2_2_E_KH_KM_LEN); > @@ -312,6 +316,7 @@ mei_hdcp_initiate_locality_check(struct device *dev, > > lc_init_in.port.integrated_port_type = data->port_type; > lc_init_in.port.physical_port = (u8)data->fw_ddi; > + lc_init_in.port.attached_transcoder = (u8)data->fw_tc; > > byte = mei_cldev_send(cldev, (u8 *)&lc_init_in, sizeof(lc_init_in)); > if (byte < 0) { > @@ -367,6 +372,7 @@ mei_hdcp_verify_lprime(struct device *dev, struct hdcp_port_data *data, > > verify_lprime_in.port.integrated_port_type = data->port_type; > verify_lprime_in.port.physical_port = (u8)data->fw_ddi; > + verify_lprime_in.port.attached_transcoder = (u8)data->fw_tc; > > memcpy(verify_lprime_in.l_prime, rx_lprime->l_prime, > HDCP_2_2_L_PRIME_LEN); > @@ -424,6 +430,7 @@ static int mei_hdcp_get_session_key(struct device *dev, > > get_skey_in.port.integrated_port_type = data->port_type; > get_skey_in.port.physical_port = (u8)data->fw_ddi; > + get_skey_in.port.attached_transcoder = (u8)data->fw_tc; > > byte = mei_cldev_send(cldev, (u8 *)&get_skey_in, sizeof(get_skey_in)); > if (byte < 0) { > @@ -488,6 +495,7 @@ mei_hdcp_repeater_check_flow_prepare_ack(struct device *dev, > > verify_repeater_in.port.integrated_port_type = data->port_type; > verify_repeater_in.port.physical_port = (u8)data->fw_ddi; > + verify_repeater_in.port.attached_transcoder = (u8)data->fw_tc; > > memcpy(verify_repeater_in.rx_info, rep_topology->rx_info, > HDCP_2_2_RXINFO_LEN); > @@ -558,6 +566,7 @@ static int mei_hdcp_verify_mprime(struct device *dev, > > verify_mprime_in.port.integrated_port_type = data->port_type; > verify_mprime_in.port.physical_port = (u8)data->fw_ddi; > + verify_mprime_in.port.attached_transcoder = (u8)data->fw_tc; > > memcpy(verify_mprime_in.m_prime, stream_ready->m_prime, > HDCP_2_2_MPRIME_LEN); > @@ -619,6 +628,7 @@ static int mei_hdcp_enable_authentication(struct device *dev, > > enable_auth_in.port.integrated_port_type = data->port_type; > enable_auth_in.port.physical_port = (u8)data->fw_ddi; > + enable_auth_in.port.attached_transcoder = (u8)data->fw_tc; > enable_auth_in.stream_type = data->streams[0].stream_type; > > byte = mei_cldev_send(cldev, (u8 *)&enable_auth_in, > @@ -673,6 +683,7 @@ mei_hdcp_close_session(struct device *dev, struct hdcp_port_data *data) > > session_close_in.port.integrated_port_type = data->port_type; > session_close_in.port.physical_port = (u8)data->fw_ddi; > + session_close_in.port.attached_transcoder = (u8)data->fw_tc; > > byte = mei_cldev_send(cldev, (u8 *)&session_close_in, > sizeof(session_close_in)); > diff --git a/drivers/misc/mei/hdcp/mei_hdcp.h b/drivers/misc/mei/hdcp/mei_hdcp.h > index e60282eb2d48..58e439d2fc1a 100644 > --- a/drivers/misc/mei/hdcp/mei_hdcp.h > +++ b/drivers/misc/mei/hdcp/mei_hdcp.h > @@ -184,8 +184,10 @@ struct hdcp_cmd_no_data { > /* Uniquely identifies the hdcp port being addressed for a given command. */ > struct hdcp_port_id { > u8 integrated_port_type; > + /* Used until Gen11.5. Must be zero for Gen11.5+ */ > u8 physical_port; > - u16 reserved; > + u8 attached_transcoder; > + u8 reserved; > } __packed; > > /*
On 2019-08-27 at 10:42:33 +0530, Sharma, Shashank wrote: > Regards > > Shashank > > On 8/22/2019 8:49 PM, Ramalingam C wrote: > > For gen12+ platform we need to pass the transcoder info > > as part of the port info into ME FW. > > > > This change fills the payload for ME FW from hdcp_port_data. > > > > Signed-off-by: Ramalingam C <ramalingam.c@intel.com> > > Acked-by: Jani Nikula <jani.nikula@intel.com> > > --- > > drivers/misc/mei/hdcp/mei_hdcp.c | 11 +++++++++++ > > drivers/misc/mei/hdcp/mei_hdcp.h | 4 +++- > > 2 files changed, 14 insertions(+), 1 deletion(-) > > > > diff --git a/drivers/misc/mei/hdcp/mei_hdcp.c b/drivers/misc/mei/hdcp/mei_hdcp.c > > index 3638c77eba26..93027fd96c71 100644 > > --- a/drivers/misc/mei/hdcp/mei_hdcp.c > > +++ b/drivers/misc/mei/hdcp/mei_hdcp.c > > @@ -58,6 +58,7 @@ mei_hdcp_initiate_session(struct device *dev, struct hdcp_port_data *data, > > session_init_in.port.integrated_port_type = data->port_type; > > session_init_in.port.physical_port = (u8)data->fw_ddi; > > As this entry is only valid till GEN11.5, don't we need GEN_CHECK here, say > (INTEL_GEN() < 12). Is that possible in MEI_FW ? Shashank, Not needed, as I915 checks the GEN# while loading the transcoder detail into hdcp_port_data. So here we can assign whatever passed as part of hdcp_port_data. -Ram > > If not, probably we have to add this gen_check while filling the fw_tc part > in I915. > > Applies for all the changes below too. > > - Shashank > > > + session_init_in.port.attached_transcoder = (u8)data->fw_tc; > > session_init_in.protocol = data->protocol; > > byte = mei_cldev_send(cldev, (u8 *)&session_init_in, > > @@ -127,6 +128,7 @@ mei_hdcp_verify_receiver_cert_prepare_km(struct device *dev, > > verify_rxcert_in.port.integrated_port_type = data->port_type; > > verify_rxcert_in.port.physical_port = (u8)data->fw_ddi; > > + verify_rxcert_in.port.attached_transcoder = (u8)data->fw_tc; > > verify_rxcert_in.cert_rx = rx_cert->cert_rx; > > memcpy(verify_rxcert_in.r_rx, &rx_cert->r_rx, HDCP_2_2_RRX_LEN); > > @@ -197,6 +199,7 @@ mei_hdcp_verify_hprime(struct device *dev, struct hdcp_port_data *data, > > send_hprime_in.port.integrated_port_type = data->port_type; > > send_hprime_in.port.physical_port = (u8)data->fw_ddi; > > + send_hprime_in.port.attached_transcoder = (u8)data->fw_tc; > > memcpy(send_hprime_in.h_prime, rx_hprime->h_prime, > > HDCP_2_2_H_PRIME_LEN); > > @@ -254,6 +257,7 @@ mei_hdcp_store_pairing_info(struct device *dev, struct hdcp_port_data *data, > > pairing_info_in.port.integrated_port_type = data->port_type; > > pairing_info_in.port.physical_port = (u8)data->fw_ddi; > > + pairing_info_in.port.attached_transcoder = (u8)data->fw_tc; > > memcpy(pairing_info_in.e_kh_km, pairing_info->e_kh_km, > > HDCP_2_2_E_KH_KM_LEN); > > @@ -312,6 +316,7 @@ mei_hdcp_initiate_locality_check(struct device *dev, > > lc_init_in.port.integrated_port_type = data->port_type; > > lc_init_in.port.physical_port = (u8)data->fw_ddi; > > + lc_init_in.port.attached_transcoder = (u8)data->fw_tc; > > byte = mei_cldev_send(cldev, (u8 *)&lc_init_in, sizeof(lc_init_in)); > > if (byte < 0) { > > @@ -367,6 +372,7 @@ mei_hdcp_verify_lprime(struct device *dev, struct hdcp_port_data *data, > > verify_lprime_in.port.integrated_port_type = data->port_type; > > verify_lprime_in.port.physical_port = (u8)data->fw_ddi; > > + verify_lprime_in.port.attached_transcoder = (u8)data->fw_tc; > > memcpy(verify_lprime_in.l_prime, rx_lprime->l_prime, > > HDCP_2_2_L_PRIME_LEN); > > @@ -424,6 +430,7 @@ static int mei_hdcp_get_session_key(struct device *dev, > > get_skey_in.port.integrated_port_type = data->port_type; > > get_skey_in.port.physical_port = (u8)data->fw_ddi; > > + get_skey_in.port.attached_transcoder = (u8)data->fw_tc; > > byte = mei_cldev_send(cldev, (u8 *)&get_skey_in, sizeof(get_skey_in)); > > if (byte < 0) { > > @@ -488,6 +495,7 @@ mei_hdcp_repeater_check_flow_prepare_ack(struct device *dev, > > verify_repeater_in.port.integrated_port_type = data->port_type; > > verify_repeater_in.port.physical_port = (u8)data->fw_ddi; > > + verify_repeater_in.port.attached_transcoder = (u8)data->fw_tc; > > memcpy(verify_repeater_in.rx_info, rep_topology->rx_info, > > HDCP_2_2_RXINFO_LEN); > > @@ -558,6 +566,7 @@ static int mei_hdcp_verify_mprime(struct device *dev, > > verify_mprime_in.port.integrated_port_type = data->port_type; > > verify_mprime_in.port.physical_port = (u8)data->fw_ddi; > > + verify_mprime_in.port.attached_transcoder = (u8)data->fw_tc; > > memcpy(verify_mprime_in.m_prime, stream_ready->m_prime, > > HDCP_2_2_MPRIME_LEN); > > @@ -619,6 +628,7 @@ static int mei_hdcp_enable_authentication(struct device *dev, > > enable_auth_in.port.integrated_port_type = data->port_type; > > enable_auth_in.port.physical_port = (u8)data->fw_ddi; > > + enable_auth_in.port.attached_transcoder = (u8)data->fw_tc; > > enable_auth_in.stream_type = data->streams[0].stream_type; > > byte = mei_cldev_send(cldev, (u8 *)&enable_auth_in, > > @@ -673,6 +683,7 @@ mei_hdcp_close_session(struct device *dev, struct hdcp_port_data *data) > > session_close_in.port.integrated_port_type = data->port_type; > > session_close_in.port.physical_port = (u8)data->fw_ddi; > > + session_close_in.port.attached_transcoder = (u8)data->fw_tc; > > byte = mei_cldev_send(cldev, (u8 *)&session_close_in, > > sizeof(session_close_in)); > > diff --git a/drivers/misc/mei/hdcp/mei_hdcp.h b/drivers/misc/mei/hdcp/mei_hdcp.h > > index e60282eb2d48..58e439d2fc1a 100644 > > --- a/drivers/misc/mei/hdcp/mei_hdcp.h > > +++ b/drivers/misc/mei/hdcp/mei_hdcp.h > > @@ -184,8 +184,10 @@ struct hdcp_cmd_no_data { > > /* Uniquely identifies the hdcp port being addressed for a given command. */ > > struct hdcp_port_id { > > u8 integrated_port_type; > > + /* Used until Gen11.5. Must be zero for Gen11.5+ */ > > u8 physical_port; > > - u16 reserved; > > + u8 attached_transcoder; > > + u8 reserved; > > } __packed; > > /*
On 8/27/2019 10:47 AM, Ramalingam C wrote: > On 2019-08-27 at 10:42:33 +0530, Sharma, Shashank wrote: >> Regards >> >> Shashank >> >> On 8/22/2019 8:49 PM, Ramalingam C wrote: >>> For gen12+ platform we need to pass the transcoder info >>> as part of the port info into ME FW. >>> >>> This change fills the payload for ME FW from hdcp_port_data. >>> >>> Signed-off-by: Ramalingam C <ramalingam.c@intel.com> >>> Acked-by: Jani Nikula <jani.nikula@intel.com> >>> --- >>> drivers/misc/mei/hdcp/mei_hdcp.c | 11 +++++++++++ >>> drivers/misc/mei/hdcp/mei_hdcp.h | 4 +++- >>> 2 files changed, 14 insertions(+), 1 deletion(-) >>> >>> diff --git a/drivers/misc/mei/hdcp/mei_hdcp.c b/drivers/misc/mei/hdcp/mei_hdcp.c >>> index 3638c77eba26..93027fd96c71 100644 >>> --- a/drivers/misc/mei/hdcp/mei_hdcp.c >>> +++ b/drivers/misc/mei/hdcp/mei_hdcp.c >>> @@ -58,6 +58,7 @@ mei_hdcp_initiate_session(struct device *dev, struct hdcp_port_data *data, >>> session_init_in.port.integrated_port_type = data->port_type; >>> session_init_in.port.physical_port = (u8)data->fw_ddi; >> As this entry is only valid till GEN11.5, don't we need GEN_CHECK here, say >> (INTEL_GEN() < 12). Is that possible in MEI_FW ? > Shashank, > > Not needed, as I915 checks the GEN# while loading the transcoder detail > into hdcp_port_data. So here we can assign whatever passed as part of > hdcp_port_data. > > -Ram Yep, just saw this in the next patch, Please feel free to use: Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> >> If not, probably we have to add this gen_check while filling the fw_tc part >> in I915. >> >> Applies for all the changes below too. >> >> - Shashank >> >>> + session_init_in.port.attached_transcoder = (u8)data->fw_tc; >>> session_init_in.protocol = data->protocol; >>> byte = mei_cldev_send(cldev, (u8 *)&session_init_in, >>> @@ -127,6 +128,7 @@ mei_hdcp_verify_receiver_cert_prepare_km(struct device *dev, >>> verify_rxcert_in.port.integrated_port_type = data->port_type; >>> verify_rxcert_in.port.physical_port = (u8)data->fw_ddi; >>> + verify_rxcert_in.port.attached_transcoder = (u8)data->fw_tc; >>> verify_rxcert_in.cert_rx = rx_cert->cert_rx; >>> memcpy(verify_rxcert_in.r_rx, &rx_cert->r_rx, HDCP_2_2_RRX_LEN); >>> @@ -197,6 +199,7 @@ mei_hdcp_verify_hprime(struct device *dev, struct hdcp_port_data *data, >>> send_hprime_in.port.integrated_port_type = data->port_type; >>> send_hprime_in.port.physical_port = (u8)data->fw_ddi; >>> + send_hprime_in.port.attached_transcoder = (u8)data->fw_tc; >>> memcpy(send_hprime_in.h_prime, rx_hprime->h_prime, >>> HDCP_2_2_H_PRIME_LEN); >>> @@ -254,6 +257,7 @@ mei_hdcp_store_pairing_info(struct device *dev, struct hdcp_port_data *data, >>> pairing_info_in.port.integrated_port_type = data->port_type; >>> pairing_info_in.port.physical_port = (u8)data->fw_ddi; >>> + pairing_info_in.port.attached_transcoder = (u8)data->fw_tc; >>> memcpy(pairing_info_in.e_kh_km, pairing_info->e_kh_km, >>> HDCP_2_2_E_KH_KM_LEN); >>> @@ -312,6 +316,7 @@ mei_hdcp_initiate_locality_check(struct device *dev, >>> lc_init_in.port.integrated_port_type = data->port_type; >>> lc_init_in.port.physical_port = (u8)data->fw_ddi; >>> + lc_init_in.port.attached_transcoder = (u8)data->fw_tc; >>> byte = mei_cldev_send(cldev, (u8 *)&lc_init_in, sizeof(lc_init_in)); >>> if (byte < 0) { >>> @@ -367,6 +372,7 @@ mei_hdcp_verify_lprime(struct device *dev, struct hdcp_port_data *data, >>> verify_lprime_in.port.integrated_port_type = data->port_type; >>> verify_lprime_in.port.physical_port = (u8)data->fw_ddi; >>> + verify_lprime_in.port.attached_transcoder = (u8)data->fw_tc; >>> memcpy(verify_lprime_in.l_prime, rx_lprime->l_prime, >>> HDCP_2_2_L_PRIME_LEN); >>> @@ -424,6 +430,7 @@ static int mei_hdcp_get_session_key(struct device *dev, >>> get_skey_in.port.integrated_port_type = data->port_type; >>> get_skey_in.port.physical_port = (u8)data->fw_ddi; >>> + get_skey_in.port.attached_transcoder = (u8)data->fw_tc; >>> byte = mei_cldev_send(cldev, (u8 *)&get_skey_in, sizeof(get_skey_in)); >>> if (byte < 0) { >>> @@ -488,6 +495,7 @@ mei_hdcp_repeater_check_flow_prepare_ack(struct device *dev, >>> verify_repeater_in.port.integrated_port_type = data->port_type; >>> verify_repeater_in.port.physical_port = (u8)data->fw_ddi; >>> + verify_repeater_in.port.attached_transcoder = (u8)data->fw_tc; >>> memcpy(verify_repeater_in.rx_info, rep_topology->rx_info, >>> HDCP_2_2_RXINFO_LEN); >>> @@ -558,6 +566,7 @@ static int mei_hdcp_verify_mprime(struct device *dev, >>> verify_mprime_in.port.integrated_port_type = data->port_type; >>> verify_mprime_in.port.physical_port = (u8)data->fw_ddi; >>> + verify_mprime_in.port.attached_transcoder = (u8)data->fw_tc; >>> memcpy(verify_mprime_in.m_prime, stream_ready->m_prime, >>> HDCP_2_2_MPRIME_LEN); >>> @@ -619,6 +628,7 @@ static int mei_hdcp_enable_authentication(struct device *dev, >>> enable_auth_in.port.integrated_port_type = data->port_type; >>> enable_auth_in.port.physical_port = (u8)data->fw_ddi; >>> + enable_auth_in.port.attached_transcoder = (u8)data->fw_tc; >>> enable_auth_in.stream_type = data->streams[0].stream_type; >>> byte = mei_cldev_send(cldev, (u8 *)&enable_auth_in, >>> @@ -673,6 +683,7 @@ mei_hdcp_close_session(struct device *dev, struct hdcp_port_data *data) >>> session_close_in.port.integrated_port_type = data->port_type; >>> session_close_in.port.physical_port = (u8)data->fw_ddi; >>> + session_close_in.port.attached_transcoder = (u8)data->fw_tc; >>> byte = mei_cldev_send(cldev, (u8 *)&session_close_in, >>> sizeof(session_close_in)); >>> diff --git a/drivers/misc/mei/hdcp/mei_hdcp.h b/drivers/misc/mei/hdcp/mei_hdcp.h >>> index e60282eb2d48..58e439d2fc1a 100644 >>> --- a/drivers/misc/mei/hdcp/mei_hdcp.h >>> +++ b/drivers/misc/mei/hdcp/mei_hdcp.h >>> @@ -184,8 +184,10 @@ struct hdcp_cmd_no_data { >>> /* Uniquely identifies the hdcp port being addressed for a given command. */ >>> struct hdcp_port_id { >>> u8 integrated_port_type; >>> + /* Used until Gen11.5. Must be zero for Gen11.5+ */ >>> u8 physical_port; >>> - u16 reserved; >>> + u8 attached_transcoder; >>> + u8 reserved; >>> } __packed; >>> /*
diff --git a/drivers/misc/mei/hdcp/mei_hdcp.c b/drivers/misc/mei/hdcp/mei_hdcp.c index 3638c77eba26..93027fd96c71 100644 --- a/drivers/misc/mei/hdcp/mei_hdcp.c +++ b/drivers/misc/mei/hdcp/mei_hdcp.c @@ -58,6 +58,7 @@ mei_hdcp_initiate_session(struct device *dev, struct hdcp_port_data *data, session_init_in.port.integrated_port_type = data->port_type; session_init_in.port.physical_port = (u8)data->fw_ddi; + session_init_in.port.attached_transcoder = (u8)data->fw_tc; session_init_in.protocol = data->protocol; byte = mei_cldev_send(cldev, (u8 *)&session_init_in, @@ -127,6 +128,7 @@ mei_hdcp_verify_receiver_cert_prepare_km(struct device *dev, verify_rxcert_in.port.integrated_port_type = data->port_type; verify_rxcert_in.port.physical_port = (u8)data->fw_ddi; + verify_rxcert_in.port.attached_transcoder = (u8)data->fw_tc; verify_rxcert_in.cert_rx = rx_cert->cert_rx; memcpy(verify_rxcert_in.r_rx, &rx_cert->r_rx, HDCP_2_2_RRX_LEN); @@ -197,6 +199,7 @@ mei_hdcp_verify_hprime(struct device *dev, struct hdcp_port_data *data, send_hprime_in.port.integrated_port_type = data->port_type; send_hprime_in.port.physical_port = (u8)data->fw_ddi; + send_hprime_in.port.attached_transcoder = (u8)data->fw_tc; memcpy(send_hprime_in.h_prime, rx_hprime->h_prime, HDCP_2_2_H_PRIME_LEN); @@ -254,6 +257,7 @@ mei_hdcp_store_pairing_info(struct device *dev, struct hdcp_port_data *data, pairing_info_in.port.integrated_port_type = data->port_type; pairing_info_in.port.physical_port = (u8)data->fw_ddi; + pairing_info_in.port.attached_transcoder = (u8)data->fw_tc; memcpy(pairing_info_in.e_kh_km, pairing_info->e_kh_km, HDCP_2_2_E_KH_KM_LEN); @@ -312,6 +316,7 @@ mei_hdcp_initiate_locality_check(struct device *dev, lc_init_in.port.integrated_port_type = data->port_type; lc_init_in.port.physical_port = (u8)data->fw_ddi; + lc_init_in.port.attached_transcoder = (u8)data->fw_tc; byte = mei_cldev_send(cldev, (u8 *)&lc_init_in, sizeof(lc_init_in)); if (byte < 0) { @@ -367,6 +372,7 @@ mei_hdcp_verify_lprime(struct device *dev, struct hdcp_port_data *data, verify_lprime_in.port.integrated_port_type = data->port_type; verify_lprime_in.port.physical_port = (u8)data->fw_ddi; + verify_lprime_in.port.attached_transcoder = (u8)data->fw_tc; memcpy(verify_lprime_in.l_prime, rx_lprime->l_prime, HDCP_2_2_L_PRIME_LEN); @@ -424,6 +430,7 @@ static int mei_hdcp_get_session_key(struct device *dev, get_skey_in.port.integrated_port_type = data->port_type; get_skey_in.port.physical_port = (u8)data->fw_ddi; + get_skey_in.port.attached_transcoder = (u8)data->fw_tc; byte = mei_cldev_send(cldev, (u8 *)&get_skey_in, sizeof(get_skey_in)); if (byte < 0) { @@ -488,6 +495,7 @@ mei_hdcp_repeater_check_flow_prepare_ack(struct device *dev, verify_repeater_in.port.integrated_port_type = data->port_type; verify_repeater_in.port.physical_port = (u8)data->fw_ddi; + verify_repeater_in.port.attached_transcoder = (u8)data->fw_tc; memcpy(verify_repeater_in.rx_info, rep_topology->rx_info, HDCP_2_2_RXINFO_LEN); @@ -558,6 +566,7 @@ static int mei_hdcp_verify_mprime(struct device *dev, verify_mprime_in.port.integrated_port_type = data->port_type; verify_mprime_in.port.physical_port = (u8)data->fw_ddi; + verify_mprime_in.port.attached_transcoder = (u8)data->fw_tc; memcpy(verify_mprime_in.m_prime, stream_ready->m_prime, HDCP_2_2_MPRIME_LEN); @@ -619,6 +628,7 @@ static int mei_hdcp_enable_authentication(struct device *dev, enable_auth_in.port.integrated_port_type = data->port_type; enable_auth_in.port.physical_port = (u8)data->fw_ddi; + enable_auth_in.port.attached_transcoder = (u8)data->fw_tc; enable_auth_in.stream_type = data->streams[0].stream_type; byte = mei_cldev_send(cldev, (u8 *)&enable_auth_in, @@ -673,6 +683,7 @@ mei_hdcp_close_session(struct device *dev, struct hdcp_port_data *data) session_close_in.port.integrated_port_type = data->port_type; session_close_in.port.physical_port = (u8)data->fw_ddi; + session_close_in.port.attached_transcoder = (u8)data->fw_tc; byte = mei_cldev_send(cldev, (u8 *)&session_close_in, sizeof(session_close_in)); diff --git a/drivers/misc/mei/hdcp/mei_hdcp.h b/drivers/misc/mei/hdcp/mei_hdcp.h index e60282eb2d48..58e439d2fc1a 100644 --- a/drivers/misc/mei/hdcp/mei_hdcp.h +++ b/drivers/misc/mei/hdcp/mei_hdcp.h @@ -184,8 +184,10 @@ struct hdcp_cmd_no_data { /* Uniquely identifies the hdcp port being addressed for a given command. */ struct hdcp_port_id { u8 integrated_port_type; + /* Used until Gen11.5. Must be zero for Gen11.5+ */ u8 physical_port; - u16 reserved; + u8 attached_transcoder; + u8 reserved; } __packed; /*