| Message ID | 20191031204557.1ed83e95@archlinux (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [PULL] 2nd set of IIO + counter new device support, features etc for the 5.5 cycle. | expand |
On Thu, Oct 31, 2019 at 08:45:57PM +0000, Jonathan Cameron wrote: > The following changes since commit 88d0facf186c6c652c2203536fecd77089b43a4e: > > staging: wfx: fix potential vulnerability to spectre (2019-10-14 15:37:19 +0200) > > are available in the Git repository at: > > https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git tags/iio-for-5.5b Pulled and pushed out, thanks. greg k-h
The following changes since commit 88d0facf186c6c652c2203536fecd77089b43a4e: staging: wfx: fix potential vulnerability to spectre (2019-10-14 15:37:19 +0200) are available in the Git repository at: https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git tags/iio-for-5.5b for you to fetch changes up to 5a3436dc3610f63d5cdf5e34af22097a6ed29a9f: dt-bindings: iio: imu: st_lsm6dsx: add lsm6dsrx device bindings (2019-10-27 16:39:48 +0000) ---------------------------------------------------------------- Second set of IIO + counter new device support, features etc for the 5.5 cycle. Note two merge commits in here, both for immutable branches based of 5.4-rc1. 1. Ti eqep driver because of some file moves in precursor patches. I suspect no one else will pull this one. 2. ab8500 refactor as changes in power supply, hwmon and mfd trees. This may come via numerous trees as well as IIO. Counter subsystem related * ti eqep - New device support with bindings. - Includes prior file move to reflect more general use of ti-pwmss. * Counter core - simplify count_read and count_write callbacks + document change. - fix a typo in docs. Various subsystems related * AB8500 - ab8500_btemp driver converted to be an IIO consumer driver. - ab8500_charger driver converted to be an IIO consumer driver. - ab8500_fg fuel gauge driver converted to be an IIO consumer driver. - ab8500 hwmon driver converted to be an IIO consumer driver. - mfd bindings augmented with the adc channels to make the above work. - drop original mfd driver. New device support * ab8500 - new ADC driver used by the above other subystems via the IIO consumer interface. * adux1020 photometric sensor - new driver and dt bindings. * fxos877cq - new driver for this simple(ish) IMU with DT bindings. * intel_mrfld_adc - new driver for the ADC found on Intel Merrifield platforms. * ltc2983 - new driver for this multi-sensor type temperature interface. Includes complex DT bindings. * max1027 - support for 12 bit devices, max1227, max1229 and max1231 + add to trivial bindings. * st_lsm6dsx - support for the LSM6DS0 6 axis MEMs sensor. Note different from the LSM6DSO which the driver already supports *sigh* - support for the LSM6DSRX 6 axis MEMs sensor. Features and cleanups * ad7303 - replace use of core mlock with a local lock with cleanly defined scope. * ad9834 - add a check for devm_clk_get failing. * at91-sama5d2 - tidy up a 0 as NULL warning. * bmp280 - endian type tidy ups. - use bulk regulator ops for a small reduction in code. - use devm_add_action... to simplify error path handling. * exynos - drop stray semicolon. - use devm_platform_ioremap_resource to reduce boilerplate. * hx711 - various tricks to improve the frequency of read out possible. * max1027 - debugfs support. - make interrupts optional. - reset at probe to get clean state. - refactors to allow addition of new device support. * maxim thermocouple - drop an unneeded semicolon. * mb1232 - yaml binding conversion. * mcp320x - tidy up an endian types in cast warning. * meson_saradc - use devm_platform_ioremap_resource to reduce boilerplate. * mpu3050 - make a poison value explicity big endian to supress a warning. * pulsedlight v2 - endian type tidy ups. * sgp30 - drop an excess semicolon. * sps30 - make truncation explicit with masking to clean up a warning. * st sensors - drop gpio include as none of these support gpios. * st_lsm6dsx - tidy up some alignment issues. - refactors to allow addition of new device support. * allow varients of irq related reg definitions. * avoid accessing active-low, open-drain regs if not provided. * allow varients of bdu/boot and reset regs. * allow for enabling or disabling wakeup sources through platform data (seems someone still uses this). - enable wake-up events for LSM6DS0 - use the drdy mask to avoid some invalid samples during initial start of sensor. - Add support to trim the timestamp. * stm32_adc - kernel-doc fixes. * stm32_dac - power management support. * stmpe-adc - Fix endian type of local variable. * twl4030 - use false / true instead of 0 / 1 for booleans. * xilinx-xadc - use devm_platform_ioremap_resouce to reduce boilerplate. * zpa2326 - reorganise buffer handling setup to be more consistent. Fixes (mostly recent additions) * cpcap-adc - Fix mising IRQF_ONESHOT that would cause warnings to be printed. * st_lsm6dsx - Sanity check the read_fifo pointer is set. - use locked read and update functions to prevent some races. - avoid accessing enable_reg if not provided. - take a lock to prevent a race in updating the config. - kernel-doc fixes. - document wakeup-source property in dt binding. - fix lsm9ds1 gyro gain definitions. ---------------------------------------------------------------- Alexandru Ardelean (2): iio: dac: ad7303: replace mlock with own lock iio: pressure: zpa2326: fix iio_triggered_buffer_postenable position Andreas Klinger (2): dt-bindings: iio: maxbotix,mb1232.yaml: transform to yaml iio: adc: hx711: optimize performance in read cycle Bartosz Golaszewski (2): iio: pressure: bmp280: use bulk regulator ops iio: pressure: bmp280: use devm action and remove labels from probe Chuhong Yuan (1): staging: iio: ad9834: add a check for devm_clk_get David Lechner (3): bus/ti-pwmss: move TI PWMSS driver from PWM to bus subsystem dt-bindings: counter: new bindings for TI eQEP counter: new TI eQEP driver Fabrice Gasnier (2): iio: dac: stm32: add power management support iio: adc: stm32-adc: fix kernel-doc warnings Jonathan Cameron (17): Merge branch 'ib-ti-eqep-5.4-rc1' into togreg Merge branch 'ib-ab8500-5.4-rc1' into HEAD iio: adc: at91-sama5d2: Replace 0 with NULL when clearing some pointers. iio: adc: mcp320x: Tidy up endian types in type cast. iio: adc: stmpe-adc: Cleanup endian type of local variable iio: chemical: sps30: Explicity truncate constant by masking iio: gyro: mpu3050: Explicity make a 'poison' value big endian iio: pressure: bmp280 endian tidy ups iio: proximity: pulsedlight v2: Tidy up an endian issue iio: adc: exynos: Drop a stray semicolon iio: adc: exynos: use devm_platform_ioremap_resource iio: adc: meson_saradc: use devm_platform_ioremap_resource iio: adc: cpcap-adc: Fix missing IRQF_ONESHOT as only threaded handler. iio: temp: maxim thermocouple: Drop unneeded semi colon. iio: adc: xilinx-xadc: use devm_platform_ioremap_resource iio: adc: twl4030: Use false / true instead of 0 / 1 with booleans iio: chemical: sgp30: drop excess semicolon Linus Walleij (8): power: supply: ab8500_btemp: Convert to IIO ADC power: supply: ab8500_charger: Convert to IIO ADC power: supply: ab8500_fg: Convert to IIO ADC hwmon: ab8500: Convert to IIO ADC mfd: ab8500: Augment DT bindings iio: adc: New driver for the AB8500 GPADC mfd: Switch the AB8500 GPADC to IIO iio: st: Drop GPIO include Lorenzo Bianconi (19): iio: imu: st_lsm6dsx: use st_lsm6dsx_read_locked in st_lsm6dsx_report_motion_event iio: imu: st_lsm6dsx: add sanity check for read_fifo pointer iio: imu: st_lsm6dsx: move irq related definitions in irq_config iio: imu: st_lsm6dsx: do not access active-low/open-drain regs if not supported iio: imu: st_lsm6dsx: move bdu/boot and reset register info in hw_settings iio: imu: st_lsm6dsx: always check enable_reg in st_lsm6dsx_event_setup iio: imu: st_lsm6dsx: rely on st_lsm6dsx_update_bits_locked configuring events iio: imu: st_lsm6dsx: grab conf mutex in st_lsm6dsx_write_event_config iio: imu: st_lsm6dsx: fix checkpatch warning iio: imu: st_lsm6dsx: add wakeup_source in st_sensors_platform_data iio: imu: st_lsm6dsx: add missing kernel documenation dt-bindings: iio: imu: st_lsm6dsx: document missing wakeup-source property iio: imu: st_lsm6dsx: enable wake-up event for LSM6DSO iio: imu: st_lsm6dsx: enable drdy-mask if available iio: imu: st_lsm6dsx: fix gyro gain definitions for LSM9DS1 iio: imu: st_lsm6dsx: add support to LSM6DS0 dt-bindings: iio: imu: st_lsm6dsx: add lsm6ds0 device bindings iio: imu: st_lsm6dsx: add support to LSM6DSRX dt-bindings: iio: imu: st_lsm6dsx: add lsm6dsrx device bindings Manivannan Sadhasivam (2): dt-bindings: iio: light: Add binding for ADUX1020 iio: light: Add support for ADUX1020 sensor Mario Tesi (1): iio: imu: st_lsm6dsx: add odr calibration feature Miquel Raynal (8): iio: adc: max1027: Add debugfs register read support iio: adc: max1027: Make it optional to use interrupts iio: adc: max1027: Reset the device at probe time iio: adc: max1027: Prepare the introduction of different resolutions iio: adc: max1027: Introduce 12-bit devices support dt-bindings: iio: adc: max1027: Mark interrupts as optional dt-bindings: Add 1027/1029/1031 SPI ADCs as trivial devices dt-bindings: Add max12xx SPI ADC series as trivial devices Nuno Sá (2): iio: temperature: Add support for LTC2983 dt-bindings: iio: Add ltc2983 documentation Robert Jones (2): dt-bindings: iio: imu: add fxos8700 imu binding iio: imu: Add support for the FXOS8700 IMU Vincent Pelletier (1): iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver William Breathitt Gray (3): counter: Simplify the count_read and count_write callbacks docs: driver-api: generic-counter: Update Count and Signal data types counter: Fix typo in action_get description .../devicetree/bindings/counter/ti-eqep.yaml | 50 + .../devicetree/bindings/iio/adc/max1027-adc.txt | 20 - .../devicetree/bindings/iio/imu/nxp,fxos8700.yaml | 76 + .../devicetree/bindings/iio/imu/st_lsm6dsx.txt | 3 + .../devicetree/bindings/iio/light/adux1020.yaml | 47 + .../bindings/iio/proximity/maxbotix,mb1232.txt | 29 - .../bindings/iio/proximity/maxbotix,mb1232.yaml | 60 + .../bindings/iio/temperature/adi,ltc2983.yaml | 480 ++++++ Documentation/devicetree/bindings/mfd/ab8500.txt | 119 ++ .../devicetree/bindings/trivial-devices.yaml | 12 + Documentation/driver-api/generic-counter.rst | 162 +- MAINTAINERS | 15 + drivers/bus/Kconfig | 9 + drivers/bus/Makefile | 1 + drivers/{pwm/pwm-tipwmss.c => bus/ti-pwmss.c} | 0 drivers/counter/104-quad-8.c | 33 +- drivers/counter/Kconfig | 11 + drivers/counter/Makefile | 1 + drivers/counter/counter.c | 101 +- drivers/counter/ftm-quaddec.c | 14 +- drivers/counter/stm32-lptimer-cnt.c | 5 +- drivers/counter/stm32-timer-cnt.c | 17 +- drivers/counter/ti-eqep.c | 466 ++++++ drivers/hwmon/Kconfig | 3 +- drivers/hwmon/ab8500.c | 65 +- drivers/iio/accel/st_accel_core.c | 1 - drivers/iio/adc/Kconfig | 25 +- drivers/iio/adc/Makefile | 2 + drivers/iio/adc/ab8500-gpadc.c | 1218 +++++++++++++++ drivers/iio/adc/at91-sama5d2_adc.c | 4 +- drivers/iio/adc/cpcap-adc.c | 2 +- drivers/iio/adc/exynos_adc.c | 6 +- drivers/iio/adc/hx711.c | 22 +- drivers/iio/adc/intel_mrfld_adc.c | 262 ++++ drivers/iio/adc/max1027.c | 180 ++- drivers/iio/adc/mcp320x.c | 2 +- drivers/iio/adc/meson_saradc.c | 4 +- drivers/iio/adc/stm32-adc-core.c | 11 +- drivers/iio/adc/stm32-adc.c | 21 +- drivers/iio/adc/stmpe-adc.c | 2 +- drivers/iio/adc/twl4030-madc.c | 18 +- drivers/iio/adc/xilinx-xadc-core.c | 4 +- drivers/iio/chemical/sgp30.c | 2 +- drivers/iio/chemical/sps30.c | 2 +- drivers/iio/dac/ad7303.c | 13 +- drivers/iio/dac/stm32-dac-core.c | 138 +- drivers/iio/dac/stm32-dac.c | 94 +- drivers/iio/gyro/mpu3050-core.c | 2 +- drivers/iio/gyro/st_gyro_core.c | 1 - drivers/iio/imu/Kconfig | 27 + drivers/iio/imu/Makefile | 5 + drivers/iio/imu/fxos8700.h | 10 + drivers/iio/imu/fxos8700_core.c | 649 ++++++++ drivers/iio/imu/fxos8700_i2c.c | 71 + drivers/iio/imu/fxos8700_spi.c | 59 + drivers/iio/imu/st_lsm6dsx/Kconfig | 3 +- drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 45 +- drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c | 22 +- drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 645 +++++--- drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c | 10 + drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c | 10 + drivers/iio/light/Kconfig | 11 + drivers/iio/light/Makefile | 1 + drivers/iio/light/adux1020.c | 849 +++++++++++ drivers/iio/magnetometer/st_magn_core.c | 1 - drivers/iio/pressure/bmp280-core.c | 129 +- drivers/iio/pressure/bmp280-i2c.c | 6 - drivers/iio/pressure/bmp280-spi.c | 6 - drivers/iio/pressure/bmp280.h | 1 - drivers/iio/pressure/st_pressure_core.c | 1 - drivers/iio/pressure/zpa2326.c | 16 +- drivers/iio/proximity/pulsedlight-lidar-lite-v2.c | 5 +- drivers/iio/temperature/Kconfig | 11 + drivers/iio/temperature/Makefile | 1 + drivers/iio/temperature/ltc2983.c | 1557 ++++++++++++++++++++ drivers/iio/temperature/maxim_thermocouple.c | 2 +- drivers/mfd/Kconfig | 7 - drivers/mfd/Makefile | 1 - drivers/mfd/ab8500-debugfs.c | 715 --------- drivers/mfd/ab8500-gpadc.c | 1075 -------------- drivers/power/supply/Kconfig | 2 +- drivers/power/supply/ab8500_btemp.c | 41 +- drivers/power/supply/ab8500_charger.c | 78 +- drivers/power/supply/ab8500_fg.c | 23 +- drivers/pwm/Kconfig | 9 - drivers/pwm/Makefile | 1 - drivers/staging/iio/frequency/ad9834.c | 4 + include/linux/counter.h | 76 +- include/linux/mfd/abx500/ab8500-gpadc.h | 75 - include/linux/platform_data/st_sensors_pdata.h | 2 + 90 files changed, 7368 insertions(+), 2729 deletions(-) create mode 100644 Documentation/devicetree/bindings/counter/ti-eqep.yaml delete mode 100644 Documentation/devicetree/bindings/iio/adc/max1027-adc.txt create mode 100644 Documentation/devicetree/bindings/iio/imu/nxp,fxos8700.yaml create mode 100644 Documentation/devicetree/bindings/iio/light/adux1020.yaml delete mode 100644 Documentation/devicetree/bindings/iio/proximity/maxbotix,mb1232.txt create mode 100644 Documentation/devicetree/bindings/iio/proximity/maxbotix,mb1232.yaml create mode 100644 Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml rename drivers/{pwm/pwm-tipwmss.c => bus/ti-pwmss.c} (100%) create mode 100644 drivers/counter/ti-eqep.c create mode 100644 drivers/iio/adc/ab8500-gpadc.c create mode 100644 drivers/iio/adc/intel_mrfld_adc.c create mode 100644 drivers/iio/imu/fxos8700.h create mode 100644 drivers/iio/imu/fxos8700_core.c create mode 100644 drivers/iio/imu/fxos8700_i2c.c create mode 100644 drivers/iio/imu/fxos8700_spi.c create mode 100644 drivers/iio/light/adux1020.c create mode 100644 drivers/iio/temperature/ltc2983.c delete mode 100644 drivers/mfd/ab8500-gpadc.c delete mode 100644 include/linux/mfd/abx500/ab8500-gpadc.h