| Message ID | 678df227-38be-47af-7ee3-741a391a196c@fivetechno.de (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/3] arm64: dts: rockchip: Remove always-on properties from regulator nodes on rk3399-roc-pc. | expand |
Hello Markus, I have been working with this as well, came across it on Armbian. I was also trying to eliminate the warning concerning the lack of port with limited success. I also missed the interrupt pin definition I see. I will test this later today. I've added Neil Armstrong for information in case any boards on the Amlogic side are similarly configured, I think a few other Rockchip ones at least are missing connector nodes, it appears to be a consistent issue presumably due to driver changes. -Tony On Dec 10, 2019, 7:45 AM, at 7:45 AM, Markus Reichl <m.reichl@fivetechno.de> wrote: >USB-C-Port 0 on rk3399-roc-pc is designed to supply the board. >To meet the power requirements of up to 45W a power delivery (PD) >compatible supply is needed. To configure the PD the node of the >fusb302 needs a connector property with desired PD description. > >Signed-off-by: Markus Reichl <m.reichl@fivetechno.de> >--- >Presently the board in mainline has to be powered from a 12V supply, >connected to two pins on the expansion header as the standard 5V >delivered by the unconfigured USB-C plug is not enough for higher >loads or peripherals on USB or M.2. > >With this patch the board requests 15V from the PD and runs fine >on high loads with NVME SSD, Ethernet, SDIO WLAN and USB peripherals. >During boot the 12V supply is still needed for some seconds, >as the fusb302 shuts down or resets the PD shortly when initializing >(BUG?). > >The board's 12V line is running presently on 5V, the default output >voltage of the MP8859 on I2C-7, for wich no mainline kernel driver >exists yet. >--- > arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi | 16 ++++++++++++++-- > 1 file changed, 14 insertions(+), 2 deletions(-) > >diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi >b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi >index 8e01b04144b7..90783b2b1d1f 100644 >--- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi >+++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi >@@ -6,6 +6,7 @@ > /dts-v1/; > #include <dt-bindings/input/linux-event-codes.h> > #include <dt-bindings/pwm/pwm.h> >+#include <dt-bindings/usb/pd.h> > #include "rk3399.dtsi" > #include "rk3399-opp.dtsi" > >@@ -540,11 +541,22 @@ fusb0: usb-typec@22 { > compatible = "fcs,fusb302"; > reg = <0x22>; > interrupt-parent = <&gpio1>; >- interrupts = <2 IRQ_TYPE_LEVEL_LOW>; >+ interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>; > pinctrl-names = "default"; > pinctrl-0 = <&fusb0_int>; > vbus-supply = <&vcc_vbus_typec0>; >- status = "okay"; >+ >+ usb_con: connector { >+ compatible = "usb-c-connector"; >+ label = "USB-C-0"; >+ power-role = "dual"; >+ try-power-role = "sink"; >+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; >+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) >+ PDO_VAR(5000, 15000, 3000) >+ PDO_PPS_APDO(5000, 15000, 3000)>; >+ op-sink-microwatt = <45000000>; >+ }; > }; > }; > >-- >2.24.0 > > >_______________________________________________ >Linux-rockchip mailing list >Linux-rockchip@lists.infradead.org >http://lists.infradead.org/mailman/listinfo/linux-rockchip
Hi Thomas, Am Donnerstag, 12. Dezember 2019, 16:46:09 CET schrieb Thomas McKahan: > Hello Markus, > > I have been working with this as well, came across it on Armbian. I was also trying to eliminate the warning concerning the lack of port with limited success. I also missed the interrupt pin definition I see. I will test this later today. Where you successful in your testing? My type-c exposure is somewhat limited so it would be nice to get another opinion ;-) > I've added Neil Armstrong for information in case any boards on the Amlogic side are similarly configured, I think a few other Rockchip ones at least are missing connector nodes, it appears to be a consistent issue presumably due to driver changes. The whole type-c topic is a somewhat undiscovered country on rk3399, due to the cross-ec hooking rk3399's type-c components. (see the cros-ec-pd extcon going to the rockchip type-c phy etc). This is presently worked on so that also everything can at some point use the kernel-internal type-c framework. But of course this doesn't hinder configuring the power-develivery in the fusb302 ICs already :-D . Heiko
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi index 8e01b04144b7..90783b2b1d1f 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi @@ -6,6 +6,7 @@ /dts-v1/; #include <dt-bindings/input/linux-event-codes.h> #include <dt-bindings/pwm/pwm.h> +#include <dt-bindings/usb/pd.h> #include "rk3399.dtsi" #include "rk3399-opp.dtsi" @@ -540,11 +541,22 @@ fusb0: usb-typec@22 { compatible = "fcs,fusb302"; reg = <0x22>; interrupt-parent = <&gpio1>; - interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&fusb0_int>; vbus-supply = <&vcc_vbus_typec0>; - status = "okay"; + + usb_con: connector { + compatible = "usb-c-connector"; + label = "USB-C-0"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) + PDO_VAR(5000, 15000, 3000) + PDO_PPS_APDO(5000, 15000, 3000)>; + op-sink-microwatt = <45000000>; + }; }; };
USB-C-Port 0 on rk3399-roc-pc is designed to supply the board. To meet the power requirements of up to 45W a power delivery (PD) compatible supply is needed. To configure the PD the node of the fusb302 needs a connector property with desired PD description. Signed-off-by: Markus Reichl <m.reichl@fivetechno.de> --- Presently the board in mainline has to be powered from a 12V supply, connected to two pins on the expansion header as the standard 5V delivered by the unconfigured USB-C plug is not enough for higher loads or peripherals on USB or M.2. With this patch the board requests 15V from the PD and runs fine on high loads with NVME SSD, Ethernet, SDIO WLAN and USB peripherals. During boot the 12V supply is still needed for some seconds, as the fusb302 shuts down or resets the PD shortly when initializing (BUG?). The board's 12V line is running presently on 5V, the default output voltage of the MP8859 on I2C-7, for wich no mainline kernel driver exists yet. --- arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi | 16 ++++++++++++++-- 1 file changed, 14 insertions(+), 2 deletions(-)