| Message ID | 20200112111341.21388-2-linus.walleij@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/2,v4] iio: light: Add DT bindings for GP2AP002 | expand |
On Sun, Jan 12, 2020 at 12:13:41PM +0100, Linus Walleij wrote: > This driver handles two different Sharp sensors that have been > proposed for merging to the mainline kernel over the years, and > already has a limited proximity-only driver in the input > subsystem. > > These components are completely different from the confusingly > similarly named Sharp GP2AP020A00F, for which we have a driver > in drivers/iio/light/gp2ap020a00f.c > > The two components GP2AP002A00F and GP2AP002S00F are > distinctively different but similar: they share the same set of > registers but differ slightly in the I2C protocol. > > Instead of the approach by the previous input driver, we create > a combined IIO proximity and light sensor driver. > > The plan is to merge this driver and delete the input driver. > > The pieces for the driver are picked all over the place after > researching and grepping through a few different vendor trees > and driver submissions. > > We merge it under the light sensors because: > > - It has similarities with the Capella CM3605 light sensor and > proximity driver which is there. > > - It is related to the GP2AP020A00F driver which is also there. > > This driver was tested with the Samsung GT-S7710 mobile phone > which has the GP2AP002S00F proximity sensor mounted. > > Cc: Stephan Gerhold <stephan@gerhold.net> > Cc: Minkyu Kang <mk7.kang@samsung.com> > Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> > Cc: Jonathan Bakker <xc-racer2@live.ca> > Cc: Oskar Andero <oskar.andero@gmail.com> > Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Thanks for all the work on the driver! It seems to work fine on samsung,golden with gp2ap002s00f. There are interrupts being sent when something moves in front of the sensor and iio-event-monitor looks good too: Tested-by: Stephan Gerhold <stephan@gerhold.net> Out of curiosity: I'm not so familiar with the IIO subsystem, is it intended that the sensor is active the whole time? Wouldn't it be better to activate it only when something is reading /dev/iio:device2? There is one problem I noticed, although I'm not sure if it is a problem in this driver. Reading one of the files in the sysfs results in: $ cat /sys/bus/iio/devices/iio\:device2/events/in_proximity_thresh_either_en Segmentation fault 8<--- cut here --- Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = cf50bdd4 *pgd=00000000 Internal error: Oops: 80000005 [#1] SMP ARM Modules linked in: hci_uart btbcm brcmfmac brcmutil CPU: 0 PID: 1419 Comm: cat Not tainted 5.5.0-rc5-postmarketos-novathor #1 Hardware name: ST-Ericsson Ux5x0 platform (Device Tree Support) PC is at 0x0 LR is at iio_ev_state_show+0x38/0x54 pc : [<00000000>] lr : [<c05774f0>] psr: a0000013 sp : ee21fc70 ip : c0860a74 fp : ee7d1178 r10: ee5bdf00 r9 : ee718600 r8 : ee465410 r7 : ee3db000 r6 : c084704c r5 : 00000000 r4 : ee3db000 r3 : 00000000 r2 : 00000000 r1 : c0860ab8 r0 : ee465400 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5787d Table: 2e73c04a DAC: 00000051 Process cat (pid: 1419, stack limit = 0x2726a873) Stack: (0xee21fc70 to 0xee220000) fc60: ee7d1160 eebb7280 c084704c c0467788 fc80: ee7d1160 00001000 c084704c c028f790 ee7d1160 ee21fdb8 ee21fd24 00000000 fca0: 00400cc0 00000001 ee5bdf00 c0238db4 ee718580 00001000 ee6ec000 ee7d1190 fcc0: ee21fdb8 00000000 00000000 00000000 ee5bdf00 ee21fd24 00001000 ee21fdb8 fce0: 00000001 c028e438 00000040 c0210924 00010000 ee21fcf8 00010000 ee5bdf00 fd00: ee21fdb8 ee21fd24 ffffe000 bf000000 00001000 c0211dcc ee21fd20 ee21fd24 fd20: ee718580 00000008 00000000 00010000 ee718580 00000010 c0c37200 00010000 fd40: 00000000 ee21fdb4 ee21fdb0 0000000f ee718500 ef0f3e00 00000000 c038763c fd60: efff21c0 80000113 00000010 c0c03e48 ef1e2840 00010000 00000000 c0c03e48 fd80: 00001000 00000000 00000000 00000010 ee21fddc c0241678 00000000 00080040 fda0: 00080060 ee21fea0 ee5bdf00 ee21fddc ef0f3e00 00000000 00000000 00000000 fdc0: 2ec75000 00000020 00000000 00010000 ee718500 00000000 00000000 ee6ec000 fde0: 00001000 ee1a9000 00001000 ee1aa000 00001000 ee052000 00001000 ee020000 fe00: 00001000 ee71a000 00001000 ee008000 00001000 ee7f9000 00001000 ee637000 fe20: 00001000 ee1a4000 00001000 ee7fa000 00001000 ee00a000 00001000 ee70f000 fe40: 00001000 ee62f000 00001000 ee705000 00001000 ee6fd000 00001000 c0c03e48 fe60: ee21fea0 ee718500 ee21fed8 01000000 00000000 ee5bdf00 00000000 00000000 fe80: 00000000 c02403f8 00000000 edc31088 eec19260 00000000 c023fd30 00000000 fea0: 00000000 00000000 ee21ff70 c0c03e48 fffff000 00000000 00000000 ee21ff30 fec0: ee5bdf00 ee6b9e40 ee6b9e40 7fffffff 00000000 c0240670 01000000 01000000 fee0: 00000000 ee6b9e40 00000000 00000000 ee21ff38 00000000 00000000 00000000 ff00: 00000000 c0c03e48 00000000 ee5bdf00 00000000 01000000 ee5bdf00 c0210f34 ff20: 01000000 00000000 00000001 edc62eb0 00000000 00000000 00000009 00000000 ff40: 00000400 c0c03e48 00000003 00000000 00000000 00000001 000000ef c0101204 ff60: ee21e000 000000ef 00000000 c02122c0 7fffffff 00000000 00000004 00000100 ff80: 00000001 c0c03e48 00000000 00000003 00000001 000000ef c0101204 ee21e000 ffa0: 000000ef c0101000 00000000 00000003 00000001 00000003 00000000 01000000 ffc0: 00000000 00000003 00000001 000000ef 00000003 01000000 01000000 00000000 ffe0: beab8c10 beab8c00 0047219d b6edaa6c 60000030 00000001 00000000 00000000 [<c05774f0>] (iio_ev_state_show) from [<c0467788>] (dev_attr_show+0x18/0x48) [<c0467788>] (dev_attr_show) from [<c028f790>] (sysfs_kf_seq_show+0x88/0xf0) [<c028f790>] (sysfs_kf_seq_show) from [<c0238db4>] (seq_read+0x15c/0x544) [<c0238db4>] (seq_read) from [<c0210924>] (do_iter_read+0x168/0x198) [<c0210924>] (do_iter_read) from [<c0211dcc>] (vfs_readv+0x60/0x94) [<c0211dcc>] (vfs_readv) from [<c0241678>] (default_file_splice_read+0x17c/0x2b0) [<c0241678>] (default_file_splice_read) from [<c02403f8>] (splice_direct_to_actor+0xd4/0x2ac) [<c02403f8>] (splice_direct_to_actor) from [<c0240670>] (do_splice_direct+0xa0/0xe0) [<c0240670>] (do_splice_direct) from [<c0210f34>] (do_sendfile+0x19c/0x354) [<c0210f34>] (do_sendfile) from [<c02122c0>] (sys_sendfile64+0x124/0x138) [<c02122c0>] (sys_sendfile64) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xee21ffa8 to 0xee21fff0) ffa0: 00000000 00000003 00000001 00000003 00000000 01000000 ffc0: 00000000 00000003 00000001 000000ef 00000003 01000000 01000000 00000000 ffe0: beab8c10 beab8c00 0047219d b6edaa6c Code: bad PC value ---[ end trace 82be3175d71f73f1 ]--- > --- > ChangeLog v3->v4: > - Realized I had to fix also the last two users of > of_property_read_u32(). Replaced with > device_property_read_u8(). Dropped unsigned byte check > because it can't be anything else. > - Change warnings about properties to "failed to obtain.." > - Return the actual error code instead of -EINVAL > - Move interpolation message to dev_dbg() > - Return with error if we fail to enable regulators on > the resume path. > ChangeLog v2->v3: > - Use the device property accessors to read the compatible > string and drop the dependency on <linux/of.h> making the > driver reusable with ACPI. > - Add a paragraph with comments on the hysteresis values. > ChangeLog v1->v2: > - Drop ifdef CONFIG_OF and of_match_ptr() to encourage > reuse with other OF-compliant hardware descriptions such > as ACPI PRP001 > - Convert success print to dev_dbg() > - Drop leftover debug read of VDD voltage > - Create two different regmap buses for the two component variants > and select the one we want depending on detected component > - Use if (ret) on all regmap accesses > - Fix up error handling in interrupt routine for proximity > - Provide some rationale for the 20-30 ms delay in the irq handler > - Use GENMASK() where applicable > - Prefix all defines with GP2AP002_* > - Drop buffer infrastructure from Kconfig > - Staticize gp2ap002_illuminance_table > --- > MAINTAINERS | 8 + > drivers/iio/light/Kconfig | 11 + > drivers/iio/light/Makefile | 1 + > drivers/iio/light/gp2ap002.c | 729 +++++++++++++++++++++++++++++++++++ > 4 files changed, 749 insertions(+) > create mode 100644 drivers/iio/light/gp2ap002.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 1372b4139ebd..dbd4236fc7f5 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -14893,6 +14893,14 @@ W: http://www.ibm.com/developerworks/linux/linux390/ > S: Supported > F: net/smc/ > > +SHARP GP2AP002A00F/GP2AP002S00F SENSOR DRIVER > +M: Linus Walleij <linus.walleij@linaro.org> > +L: linux-iio@vger.kernel.org > +T: git git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git > +S: Maintained > +F: drivers/iio/light/gp2ap002.c > +F: Documentation/devicetree/bindings/iio/light/sharp,gp2ap002.yaml > + > SHARP RJ54N1CB0C SENSOR DRIVER > M: Jacopo Mondi <jacopo@jmondi.org> > L: linux-media@vger.kernel.org > diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig > index 9968f982fbc7..307412c79c53 100644 > --- a/drivers/iio/light/Kconfig > +++ b/drivers/iio/light/Kconfig > @@ -159,6 +159,17 @@ config IIO_CROS_EC_LIGHT_PROX > To compile this driver as a module, choose M here: > the module will be called cros_ec_light_prox. > > +config GP2AP002 > + tristate "Sharp GP2AP002 Proximity/ALS sensor" > + depends on I2C > + select REGMAP > + help > + Say Y here if you have a Sharp GP2AP002 proximity/ALS combo-chip > + hooked to an I2C bus. > + > + To compile this driver as a module, choose M here: the > + module will be called gp2ap002. > + > config GP2AP020A00F > tristate "Sharp GP2AP020A00F Proximity/ALS sensor" > depends on I2C > diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile > index c98d1cefb861..264a76039006 100644 > --- a/drivers/iio/light/Makefile > +++ b/drivers/iio/light/Makefile > @@ -18,6 +18,7 @@ obj-$(CONFIG_CM3323) += cm3323.o > obj-$(CONFIG_CM3605) += cm3605.o > obj-$(CONFIG_CM36651) += cm36651.o > obj-$(CONFIG_IIO_CROS_EC_LIGHT_PROX) += cros_ec_light_prox.o > +obj-$(CONFIG_GP2AP002) += gp2ap002.o > obj-$(CONFIG_GP2AP020A00F) += gp2ap020a00f.o > obj-$(CONFIG_HID_SENSOR_ALS) += hid-sensor-als.o > obj-$(CONFIG_HID_SENSOR_PROX) += hid-sensor-prox.o > diff --git a/drivers/iio/light/gp2ap002.c b/drivers/iio/light/gp2ap002.c > new file mode 100644 > index 000000000000..96016c3c03ef > --- /dev/null > +++ b/drivers/iio/light/gp2ap002.c > @@ -0,0 +1,729 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * These are the two Sharp GP2AP002 variants supported by this driver: > + * GP2AP002A00F Ambient Light and Proximity Sensor > + * GP2AP002S00F Proximity Sensor > + * > + * Copyright (C) 2019 Linaro Ltd. > + * Author: Linus Walleij <linus.walleij@linaro.org> > + * > + * Based partly on the code in Sony Ericssons GP2AP00200F driver by > + * Courtney Cavin and Oskar Andero in drivers/input/misc/gp2ap002a00f.c > + * Based partly on a Samsung misc driver submitted by > + * Donggeun Kim & Minkyu Kang in 2011: > + * https://lore.kernel.org/lkml/1315556546-7445-1-git-send-email-dg77.kim@samsung.com/ > + * Based partly on a submission by > + * Jonathan Bakker and Paweł Chmiel in january 2019: > + * https://lore.kernel.org/linux-input/20190125175045.22576-1-pawel.mikolaj.chmiel@gmail.com/ > + * Based partly on code from the Samsung GT-S7710 by <mjchen@sta.samsung.com> > + * Based partly on the code in LG Electronics GP2AP00200F driver by > + * Kenobi Lee <sungyoung.lee@lge.com> and EunYoung Cho <ey.cho@lge.com> > + */ > +#include <linux/module.h> > +#include <linux/i2c.h> > +#include <linux/regmap.h> > +#include <linux/iio/iio.h> > +#include <linux/iio/sysfs.h> > +#include <linux/iio/events.h> > +#include <linux/iio/consumer.h> /* To get our ADC channel */ > +#include <linux/iio/types.h> /* To deal with our ADC channel */ > +#include <linux/init.h> > +#include <linux/delay.h> > +#include <linux/regulator/consumer.h> > +#include <linux/interrupt.h> > +#include <linux/bits.h> > +#include <linux/math64.h> > +#include <linux/pm.h> > + > +#define GP2AP002_PROX_CHANNEL 0 > +#define GP2AP002_ALS_CHANNEL 1 > + > +/* ------------------------------------------------------------------------ */ > +/* ADDRESS SYMBOL DATA Init R/W */ > +/* D7 D6 D5 D4 D3 D2 D1 D0 */ > +/* ------------------------------------------------------------------------ */ > +/* 0 PROX X X X X X X X VO H'00 R */ > +/* 1 GAIN X X X X LED0 X X X H'00 W */ > +/* 2 HYS HYSD HYSC1 HYSC0 X HYSF3 HYSF2 HYSF1 HYSF0 H'00 W */ > +/* 3 CYCLE X X CYCL2 CYCL1 CYCL0 OSC2 X X H'00 W */ > +/* 4 OPMOD X X X ASD X X VCON SSD H'00 W */ > +/* 6 CON X X X OCON1 OCON0 X X X H'00 W */ > +/* ------------------------------------------------------------------------ */ > +/* VO :Proximity sensing result(0: no detection, 1: detection) */ > +/* LED0 :Select switch for LED driver's On-registence(0:2x higher, 1:normal)*/ > +/* HYSD/HYSF :Adjusts the receiver sensitivity */ > +/* OSC :Select switch internal clocl frequency hoppling(0:effective) */ > +/* CYCL :Determine the detection cycle(typically 8ms, up to 128x) */ > +/* SSD :Software Shutdown function(0:shutdown, 1:operating) */ > +/* VCON :VOUT output method control(0:normal, 1:interrupt) */ > +/* ASD :Select switch for analog sleep function(0:ineffective, 1:effective)*/ > +/* OCON :Select switch for enabling/disabling VOUT (00:enable, 11:disable) */ > + > +#define GP2AP002_PROX 0x00 > +#define GP2AP002_GAIN 0x01 > +#define GP2AP002_HYS 0x02 > +#define GP2AP002_CYCLE 0x03 > +#define GP2AP002_OPMOD 0x04 > +#define GP2AP002_CON 0x06 > + > +#define GP2AP002_PROX_VO_DETECT BIT(0) > + > +/* Setting this bit to 0 means 2x higher LED resistance */ > +#define GP2AP002_GAIN_LED_NORMAL BIT(3) > + > +/* > + * These bits adjusts the proximity sensitivity, determining characteristics > + * of the detection distance and its hysteresis. > + */ > +#define GP2AP002_HYS_HYSD_SHIFT 7 > +#define GP2AP002_HYS_HYSD_MASK BIT(7) > +#define GP2AP002_HYS_HYSC_SHIFT 5 > +#define GP2AP002_HYS_HYSC_MASK GENMASK(6, 5) > +#define GP2AP002_HYS_HYSF_SHIFT 0 > +#define GP2AP002_HYS_HYSF_MASK GENMASK(3, 0) > +#define GP2AP002_HYS_MASK (GP2AP002_HYS_HYSD_MASK | \ > + GP2AP002_HYS_HYSC_MASK | \ > + GP2AP002_HYS_HYSF_MASK) > + > +/* > + * These values determine the detection cycle response time > + * 0: 8ms, 1: 16ms, 2: 32ms, 3: 64ms, 4: 128ms, > + * 5: 256ms, 6: 512ms, 7: 1024ms > + */ > +#define GP2AP002_CYCLE_CYCL_SHIFT 3 > +#define GP2AP002_CYCLE_CYCL_MASK GENMASK(5, 3) > + > +/* > + * Select switch for internal clock frequency hopping > + * 0: effective, > + * 1: ineffective > + */ > +#define GP2AP002_CYCLE_OSC_EFFECTIVE 0 > +#define GP2AP002_CYCLE_OSC_INEFFECTIVE BIT(2) > +#define GP2AP002_CYCLE_OSC_MASK BIT(2) > + > +/* Analog sleep effective */ > +#define GP2AP002_OPMOD_ASD BIT(4) > +/* Enable chip */ > +#define GP2AP002_OPMOD_SSD_OPERATING BIT(0) > +/* IRQ mode */ > +#define GP2AP002_OPMOD_VCON_IRQ BIT(1) > +#define GP2AP002_OPMOD_MASK (BIT(0) | BIT(1) | BIT(4)) > + > +/* > + * Select switch for enabling/disabling Vout pin > + * 0: enable > + * 2: force to go Low > + * 3: force to go High > + */ > +#define GP2AP002_CON_OCON_SHIFT 3 > +#define GP2AP002_CON_OCON_ENABLE (0x0 << GP2AP002_CON_OCON_SHIFT) > +#define GP2AP002_CON_OCON_LOW (0x2 << GP2AP002_CON_OCON_SHIFT) > +#define GP2AP002_CON_OCON_HIGH (0x3 << GP2AP002_CON_OCON_SHIFT) > +#define GP2AP002_CON_OCON_MASK (0x3 << GP2AP002_CON_OCON_SHIFT) > + > +/** > + * struct gp2ap002 - GP2AP002 state > + * @map: regmap pointer for the i2c regmap > + * @dev: pointer to parent device > + * @vdd: regulator controlling VDD > + * @vio: regulator controlling VIO > + * @alsout: IIO ADC channel to convert the ALSOUT signal > + * @is_gp2ap002s00f: this is the GP2AP002F variant of the chip > + */ > +struct gp2ap002 { > + struct regmap *map; > + struct device *dev; > + struct regulator *vdd; > + struct regulator *vio; > + struct iio_channel *alsout; > + enum iio_event_direction dir; > + u8 hys_far; > + u8 hys_close; > + bool is_gp2ap002s00f; > +}; > + > +static irqreturn_t gp2ap002_prox_irq(int irq, void *d) > +{ > + struct iio_dev *indio_dev = d; > + struct gp2ap002 *gp2ap002 = iio_priv(indio_dev); > + u64 ev; > + int val; > + int ret; > + > + ret = regmap_read(gp2ap002->map, GP2AP002_PROX, &val); > + if (ret) { > + dev_err(gp2ap002->dev, "error reading proximity\n"); > + goto err_retrig; > + } > + > + if (val & GP2AP002_PROX_VO_DETECT) { > + /* Close */ > + dev_dbg(gp2ap002->dev, "close\n"); > + ret = regmap_write(gp2ap002->map, GP2AP002_HYS, > + gp2ap002->hys_far); > + if (ret) > + dev_err(gp2ap002->dev, > + "error setting up proximity hysteresis\n"); > + ev = IIO_UNMOD_EVENT_CODE(IIO_PROXIMITY, GP2AP002_PROX_CHANNEL, > + IIO_EV_TYPE_THRESH, IIO_EV_DIR_RISING); > + } else { > + /* Far */ > + dev_dbg(gp2ap002->dev, "far\n"); > + ret = regmap_write(gp2ap002->map, GP2AP002_HYS, > + gp2ap002->hys_close); > + if (ret) > + dev_err(gp2ap002->dev, > + "error setting up proximity hysteresis\n"); > + ev = IIO_UNMOD_EVENT_CODE(IIO_PROXIMITY, GP2AP002_PROX_CHANNEL, > + IIO_EV_TYPE_THRESH, IIO_EV_DIR_FALLING); > + } > + iio_push_event(indio_dev, ev, iio_get_time_ns(indio_dev)); > + > + /* > + * After changing hysteresis, we need to wait for one detection > + * cycle to see if anything changed, or we will just trigger the > + * previous interrupt again. A detection cycle depends on the CYCLE > + * register, we are hard-coding ~8 ms in probe() so wait some more > + * than this, 20-30 ms. > + */ > + usleep_range(20000, 30000); > + > +err_retrig: > + ret = regmap_write(gp2ap002->map, GP2AP002_CON, > + GP2AP002_CON_OCON_ENABLE); > + if (ret) > + dev_err(gp2ap002->dev, "error setting up VOUT control\n"); > + > + return IRQ_HANDLED; > +} > + > +struct gp2ap002_illuminance { > + unsigned int curr; > + unsigned int lux; > +}; > + > +/* > + * This array maps current and lux. > + * > + * Ambient light sensing range is 3 to 55000 lux. > + * > + * This mapping is based on the following formula. > + * illuminance = 10 ^ (current / 10) > + */ > +static const struct gp2ap002_illuminance gp2ap002_illuminance_table[] = { > + { .curr = 5, .lux = 3 }, > + { .curr = 6, .lux = 4 }, > + { .curr = 7, .lux = 5 }, > + { .curr = 8, .lux = 6 }, > + { .curr = 9, .lux = 8 }, > + { .curr = 10, .lux = 10 }, > + { .curr = 11, .lux = 12 }, > + { .curr = 12, .lux = 16 }, > + { .curr = 13, .lux = 20 }, > + { .curr = 14, .lux = 25 }, > + { .curr = 15, .lux = 32 }, > + { .curr = 16, .lux = 40 }, > + { .curr = 17, .lux = 50 }, > + { .curr = 18, .lux = 63 }, > + { .curr = 19, .lux = 79 }, > + { .curr = 20, .lux = 100 }, > + { .curr = 21, .lux = 126 }, > + { .curr = 22, .lux = 158 }, > + { .curr = 23, .lux = 200 }, > + { .curr = 24, .lux = 251 }, > + { .curr = 25, .lux = 316 }, > + { .curr = 26, .lux = 398 }, > + { .curr = 27, .lux = 501 }, > + { .curr = 28, .lux = 631 }, > + { .curr = 29, .lux = 794 }, > + { .curr = 30, .lux = 1000 }, > + { .curr = 31, .lux = 1259 }, > + { .curr = 32, .lux = 1585 }, > + { .curr = 33, .lux = 1995 }, > + { .curr = 34, .lux = 2512 }, > + { .curr = 35, .lux = 3162 }, > + { .curr = 36, .lux = 3981 }, > + { .curr = 37, .lux = 5012 }, > + { .curr = 38, .lux = 6310 }, > + { .curr = 39, .lux = 7943 }, > + { .curr = 40, .lux = 10000 }, > + { .curr = 41, .lux = 12589 }, > + { .curr = 42, .lux = 15849 }, > + { .curr = 43, .lux = 19953 }, > + { .curr = 44, .lux = 25119 }, > + { .curr = 45, .lux = 31623 }, > + { .curr = 46, .lux = 39811 }, > + { .curr = 47, .lux = 50119 }, > +}; > + > +static int gp2ap002_get_lux(struct gp2ap002 *gp2ap002) > +{ > + const struct gp2ap002_illuminance *ill1; > + const struct gp2ap002_illuminance *ill2; > + int ret, res; > + int i; > + > + ret = iio_read_channel_processed(gp2ap002->alsout, &res); > + if (ret < 0) > + return ret; > + > + dev_dbg(gp2ap002->dev, "read %d mA from ADC\n", res); > + > + ill1 = &gp2ap002_illuminance_table[0]; > + if (res < ill1->curr) { > + dev_dbg(gp2ap002->dev, "total darkness\n"); > + return 0; > + } > + for (i = 0; i < ARRAY_SIZE(gp2ap002_illuminance_table) - 1; i++) { > + ill1 = &gp2ap002_illuminance_table[i]; > + ill2 = &gp2ap002_illuminance_table[i + 1]; > + > + if (res > ill2->curr) > + continue; > + if ((res <= ill1->curr) && (res >= ill2->curr)) > + break; > + } > + if (res > ill2->curr) { > + dev_info_once(gp2ap002->dev, "max current overflow\n"); > + return ill2->curr; > + } > + /* Interpolate and return */ > + dev_dbg(gp2ap002->dev, "interpolate index %d and %d\n", i, i + 1); > + /* How many steps along the curve */ > + i = res - ill1->curr; /* x - x0 */ > + /* Linear interpolation */ > + return ill1->lux + i * > + ((ill2->lux - ill1->lux) / (ill2->curr - ill1->curr)); > +} > + > +static int gp2ap002_read_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, > + int *val, int *val2, long mask) > +{ > + struct gp2ap002 *gp2ap002 = iio_priv(indio_dev); > + int ret; > + > + switch (mask) { > + case IIO_CHAN_INFO_RAW: > + switch (chan->type) { > + case IIO_LIGHT: > + ret = gp2ap002_get_lux(gp2ap002); > + if (ret < 0) > + return ret; > + *val = ret; > + return IIO_VAL_INT; > + default: > + return -EINVAL; > + } > + default: > + return -EINVAL; > + } > +} > + > +static const struct iio_info gp2ap002_info = { > + .read_raw = gp2ap002_read_raw, > +}; > + > +static const struct iio_event_spec gp2ap002_events[] = { > + { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_EITHER, > + .mask_separate = BIT(IIO_EV_INFO_ENABLE), > + }, > +}; > + > +static const struct iio_chan_spec gp2ap002_channels[] = { > + { > + .type = IIO_PROXIMITY, > + .event_spec = gp2ap002_events, > + .num_event_specs = ARRAY_SIZE(gp2ap002_events), > + }, > + { > + .type = IIO_LIGHT, > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > + .channel = GP2AP002_ALS_CHANNEL, > + }, > +}; > + > +/* > + * We need a special regmap because this hardware expects to > + * write single bytes to registers but read a 16bit word on some > + * variants and discard the lower 8 bits so combine > + * i2c_smbus_read_word_data() with i2c_smbus_write_byte_data() > + * selectively like this. > + */ > +static int gp2ap002a00f_regmap_i2c_read(void *context, unsigned int reg, > + unsigned int *val) > +{ > + struct device *dev = context; > + struct i2c_client *i2c = to_i2c_client(dev); > + int ret; > + > + ret = i2c_smbus_read_byte_data(i2c, reg); > + if (ret < 0) > + return ret; > + *val = ret & 0xff; > + > + return 0; > +} > + > +static int gp2ap002s00f_regmap_i2c_read(void *context, unsigned int reg, > + unsigned int *val) > +{ > + struct device *dev = context; > + struct i2c_client *i2c = to_i2c_client(dev); > + int ret; > + > + ret = i2c_smbus_read_word_data(i2c, reg); > + if (ret < 0) > + return ret; > + > + *val = (ret >> 8) & 0xFF; > + > + return 0; > +} > + > +static int gp2ap002_regmap_i2c_write(void *context, unsigned int reg, > + unsigned int val) > +{ > + struct device *dev = context; > + struct i2c_client *i2c = to_i2c_client(dev); > + > + return i2c_smbus_write_byte_data(i2c, reg, val); > +} > + > +static struct regmap_bus gp2ap002a00f_regmap_bus = { > + .reg_read = gp2ap002a00f_regmap_i2c_read, > + .reg_write = gp2ap002_regmap_i2c_write, > +}; > + > +static struct regmap_bus gp2ap002s00f_regmap_bus = { > + .reg_read = gp2ap002s00f_regmap_i2c_read, > + .reg_write = gp2ap002_regmap_i2c_write, > +}; > + > +static int gp2ap002_init(struct gp2ap002 *gp2ap002) > +{ > + int ret; > + > + /* Set up the IR LED resistance */ > + ret = regmap_write(gp2ap002->map, GP2AP002_GAIN, > + GP2AP002_GAIN_LED_NORMAL); > + if (ret) { > + dev_err(gp2ap002->dev, "error setting up LED gain\n"); > + return ret; > + } > + ret = regmap_write(gp2ap002->map, GP2AP002_HYS, gp2ap002->hys_far); > + if (ret) { > + dev_err(gp2ap002->dev, > + "error setting up proximity hysteresis\n"); > + return ret; > + } > + > + /* Disable internal frequency hopping */ > + ret = regmap_write(gp2ap002->map, GP2AP002_CYCLE, > + GP2AP002_CYCLE_OSC_INEFFECTIVE); > + if (ret) { > + dev_err(gp2ap002->dev, > + "error setting up internal frequency hopping\n"); > + return ret; > + } > + > + /* Enable chip and IRQ, disable analog sleep */ > + ret = regmap_write(gp2ap002->map, GP2AP002_OPMOD, > + GP2AP002_OPMOD_SSD_OPERATING | > + GP2AP002_OPMOD_VCON_IRQ); > + if (ret) { > + dev_err(gp2ap002->dev, "error setting up operation mode\n"); > + return ret; > + } > + > + /* Interrupt on VOUT enabled */ > + ret = regmap_write(gp2ap002->map, GP2AP002_CON, > + GP2AP002_CON_OCON_ENABLE); > + if (ret) > + dev_err(gp2ap002->dev, "error setting up VOUT control\n"); > + > + return ret; > +} > + > +static int gp2ap002_probe(struct i2c_client *client, > + const struct i2c_device_id *id) > +{ > + struct gp2ap002 *gp2ap002; > + struct iio_dev *indio_dev; > + struct device *dev = &client->dev; > + enum iio_chan_type ch_type; > + static const struct regmap_config config = { > + .reg_bits = 8, > + .val_bits = 8, > + .max_register = GP2AP002_CON, > + }; > + struct regmap_bus *rbus; > + struct regmap *regmap; > + int num_chan; > + const char *compat; > + u8 val; > + int ret; > + > + indio_dev = devm_iio_device_alloc(dev, sizeof(*gp2ap002)); > + if (!indio_dev) > + return -ENOMEM; > + i2c_set_clientdata(client, indio_dev); > + > + gp2ap002 = iio_priv(indio_dev); > + gp2ap002->dev = dev; > + > + /* > + * Check the device compatible like this makes it possible to use > + * ACPI PRP0001 for registering the sensor using device tree > + * properties. > + */ > + ret = device_property_read_string(dev, "compatible", &compat); > + if (ret) { > + dev_err(dev, "cannot check compatible\n"); > + return ret; > + } > + gp2ap002->is_gp2ap002s00f = !strcmp(compat, "sharp,gp2ap002s00f"); > + > + if (gp2ap002->is_gp2ap002s00f) > + rbus = &gp2ap002s00f_regmap_bus; > + else > + rbus = &gp2ap002a00f_regmap_bus; > + > + regmap = devm_regmap_init(dev, rbus, dev, &config); > + if (IS_ERR(regmap)) { > + dev_err(dev, "Failed to register i2c regmap %d\n", > + (int)PTR_ERR(regmap)); > + return PTR_ERR(regmap); > + } > + gp2ap002->map = regmap; > + > + /* > + * The hysteresis settings are coded into the device tree as values > + * to be written into the hysteresis register. The datasheet defines > + * modes "A", "B1" and "B2" with fixed values to be use but vendor > + * code trees for actual devices are tweaking these values and refer to > + * modes named things like "B1.5". To be able to support any devices, > + * we allow passing an arbitrary hysteresis setting for "near" and > + * "far". > + */ > + > + /* Check the device tree for the IR LED hysteresis */ > + ret = device_property_read_u8(dev, "sharp,proximity-far-hysteresis", > + &val); > + if (ret) { > + dev_err(dev, "failed to obtain proximity far setting\n"); > + return ret; > + } > + dev_dbg(dev, "proximity far setting %02x\n", val); > + gp2ap002->hys_far = val; > + > + ret = device_property_read_u8(dev, "sharp,proximity-close-hysteresis", > + &val); > + if (ret) { > + dev_err(dev, "failed to obtain proximity close setting\n"); > + return ret; > + } > + dev_dbg(dev, "proximity close setting %02x\n", val); > + gp2ap002->hys_close = val; > + > + /* The GP2AP002A00F has a light sensor too */ > + if (!gp2ap002->is_gp2ap002s00f) { > + gp2ap002->alsout = devm_iio_channel_get(dev, "alsout"); > + if (IS_ERR(gp2ap002->alsout)) { > + if (PTR_ERR(gp2ap002->alsout) == -ENODEV) { > + dev_err(dev, "no ADC, deferring...\n"); > + return -EPROBE_DEFER; > + } > + dev_err(dev, "failed to get ALSOUT ADC channel\n"); > + return PTR_ERR(gp2ap002->alsout); > + } > + ret = iio_get_channel_type(gp2ap002->alsout, &ch_type); > + if (ret < 0) > + return ret; > + if (ch_type != IIO_CURRENT) { > + dev_err(dev, > + "wrong type of IIO channel specified for ALSOUT\n"); > + return -EINVAL; > + } > + } > + > + gp2ap002->vdd = devm_regulator_get(dev, "vdd"); > + if (IS_ERR(gp2ap002->vdd)) { > + dev_err(dev, "failed to get VDD regulator\n"); > + return PTR_ERR(gp2ap002->vdd); > + } > + gp2ap002->vio = devm_regulator_get(dev, "vio"); > + if (IS_ERR(gp2ap002->vio)) { > + dev_err(dev, "failed to get VIO regulator\n"); > + return PTR_ERR(gp2ap002->vio); > + } > + > + /* Operating voltage 2.4V .. 3.6V according to datasheet */ > + ret = regulator_set_voltage(gp2ap002->vdd, 2400000, 3600000); > + if (ret) { > + dev_err(dev, "failed to sett VDD voltage\n"); > + return ret; > + } > + > + /* VIO should be between 1.65V and VDD */ > + ret = regulator_get_voltage(gp2ap002->vdd); > + if (ret < 0) { > + dev_err(dev, "failed to get VIO voltage\n"); > + return ret; > + } > + ret = regulator_set_voltage(gp2ap002->vio, 1650000, ret); > + if (ret) { > + dev_err(dev, "failed to set VIO voltage\n"); > + return ret; > + } > + > + ret = regulator_enable(gp2ap002->vdd); > + if (ret) { > + dev_err(dev, "failed to enable VDD regulator\n"); > + return ret; > + } > + ret = regulator_enable(gp2ap002->vio); > + if (ret) { > + dev_err(dev, "failed to enable VIO regulator\n"); > + goto out_disable_vdd; > + } > + > + msleep(20); > + > + ret = gp2ap002_init(gp2ap002); > + if (ret) { > + dev_err(dev, "initialization failed\n"); > + goto out_disable_vio; > + } > + > + ret = devm_request_threaded_irq(dev, client->irq, NULL, > + gp2ap002_prox_irq, IRQF_ONESHOT, > + "gp2ap002", indio_dev); > + if (ret) { > + dev_err(dev, "unable to request IRQ\n"); > + goto out_disable_vio; > + } > + > + indio_dev->dev.parent = dev; > + indio_dev->info = &gp2ap002_info; > + indio_dev->name = "gp2ap002"; > + indio_dev->channels = gp2ap002_channels; > + /* Skip light channel for the proximity-only sensor */ > + num_chan = ARRAY_SIZE(gp2ap002_channels); > + if (gp2ap002->is_gp2ap002s00f) > + num_chan--; > + indio_dev->num_channels = num_chan; > + indio_dev->modes = INDIO_DIRECT_MODE; > + > + ret = iio_device_register(indio_dev); > + if (ret) > + goto out_disable_vio; > + dev_dbg(dev, "Sharp GP2AP002 probed successfully\n"); > + > + return 0; > + > +out_disable_vio: > + regulator_disable(gp2ap002->vio); > +out_disable_vdd: > + regulator_disable(gp2ap002->vdd); > + return ret; > +} > + > +static int gp2ap002_remove(struct i2c_client *client) > +{ > + struct iio_dev *indio_dev = i2c_get_clientdata(client); > + struct gp2ap002 *gp2ap002 = iio_priv(indio_dev); > + > + iio_device_unregister(indio_dev); > + regulator_disable(gp2ap002->vio); > + regulator_disable(gp2ap002->vdd); > + > + return 0; > +} > + > +static int __maybe_unused gp2ap002_pm_suspend(struct device *dev) > +{ > + struct iio_dev *indio_dev = dev_get_drvdata(dev); > + struct gp2ap002 *gp2ap002 = iio_priv(indio_dev); > + int ret; > + > + /* Disable chip and IRQ, everything off */ > + ret = regmap_write(gp2ap002->map, GP2AP002_OPMOD, 0x00); > + if (ret) { > + dev_err(gp2ap002->dev, "error setting up operation mode\n"); > + return ret; > + } > + /* > + * As these regulators may be shared, at least we are now in > + * sleep even if the regulators aren't really turned off. > + */ > + regulator_disable(gp2ap002->vio); > + regulator_disable(gp2ap002->vdd); > + > + return 0; > +} > + > +static int __maybe_unused gp2ap002_pm_resume(struct device *dev) > +{ > + struct iio_dev *indio_dev = dev_get_drvdata(dev); > + struct gp2ap002 *gp2ap002 = iio_priv(indio_dev); > + int ret; > + > + ret = regulator_enable(gp2ap002->vdd); > + if (ret) { > + dev_err(dev, "failed to enable VDD regulator in resume path\n"); > + return ret; > + } > + ret = regulator_enable(gp2ap002->vio); > + if (ret) { > + dev_err(dev, "failed to enable VIO regulator in resume path\n"); > + return ret; > + } > + > + msleep(20); > + > + ret = gp2ap002_init(gp2ap002); > + if (ret) { > + dev_err(dev, "re-initialization failed\n"); > + return ret; > + } > + > + return 0; > +} > + > +static const struct dev_pm_ops gp2ap002_dev_pm_ops = { > + SET_SYSTEM_SLEEP_PM_OPS(gp2ap002_pm_suspend, > + gp2ap002_pm_resume) > +}; > + > +static const struct i2c_device_id gp2ap002_id_table[] = { > + { "gp2ap002", 0 }, > + { }, > +}; > +MODULE_DEVICE_TABLE(i2c, gp2ap002_id); > + > +static const struct of_device_id gp2ap002_of_match[] = { > + { .compatible = "sharp,gp2ap002a00f" }, > + { .compatible = "sharp,gp2ap002s00f" }, > + { }, > +}; > +MODULE_DEVICE_TABLE(of, gp2ap002_of_match); > + > +static struct i2c_driver gp2ap002_driver = { > + .driver = { > + .name = "gp2ap002", > + .of_match_table = gp2ap002_of_match, > + .pm = &gp2ap002_dev_pm_ops, > + }, > + .probe = gp2ap002_probe, > + .remove = gp2ap002_remove, > + .id_table = gp2ap002_id_table, > +}; > +module_i2c_driver(gp2ap002_driver); > + > +MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>"); > +MODULE_DESCRIPTION("GP2AP002 ambient light and proximity sensor driver"); > +MODULE_LICENSE("GPL v2"); > -- > 2.21.0 >
On Sun, Jan 12, 2020 at 5:54 PM Stephan Gerhold <stephan@gerhold.net> wrote: > It seems to work fine on samsung,golden with gp2ap002s00f. > There are interrupts being sent when something moves in front of the > sensor and iio-event-monitor looks good too: > > Tested-by: Stephan Gerhold <stephan@gerhold.net> Thanks! I think I'm up at v7 or something on this driver and now it looks good. > Out of curiosity: I'm not so familiar with the IIO subsystem, > is it intended that the sensor is active the whole time? > Wouldn't it be better to activate it only when something is reading > /dev/iio:device2? IMO the best way to power manage an IIO sensor is like I do in drivers/iio/gyro/mpu3050-core.c Of course I think it is excellent code since I wrote it. Beware of hubris in the driver. The idea is to take the runtime pm handle on the device whenever in use (reading values from the hardware or using the trigger), and then use autosuspend to completely shut it down (including regulators) when not in use. If the power-up time for the sensor is long, then the autosuspend timeout should be proportionally longer, like a magnitude or two above. With the proximity events I have this problem that I don't know in the driver if someone had opened the file to read events or not, only the core knows, I think. I just emit my events and be happy. Jonathan: is there a way for the driver to know if someone is listening on the event interface? > There is one problem I noticed, although I'm not sure if it is a problem > in this driver. Reading one of the files in the sysfs results in: > > $ cat /sys/bus/iio/devices/iio\:device2/events/in_proximity_thresh_either_en > Segmentation fault That looks like an ordinary bug, but that seems to be for the core? Hm... Yours, Linus Walleij
On Mon, 13 Jan 2020 22:02:00 +0100 Linus Walleij <linus.walleij@linaro.org> wrote: > On Sun, Jan 12, 2020 at 5:54 PM Stephan Gerhold <stephan@gerhold.net> wrote: > > > It seems to work fine on samsung,golden with gp2ap002s00f. > > There are interrupts being sent when something moves in front of the > > sensor and iio-event-monitor looks good too: > > > > Tested-by: Stephan Gerhold <stephan@gerhold.net> > > Thanks! I think I'm up at v7 or something on this driver > and now it looks good. > > > Out of curiosity: I'm not so familiar with the IIO subsystem, > > is it intended that the sensor is active the whole time? > > Wouldn't it be better to activate it only when something is reading > > /dev/iio:device2? > > IMO the best way to power manage an IIO sensor is like I do in > drivers/iio/gyro/mpu3050-core.c > > Of course I think it is excellent code since I wrote it. Beware > of hubris in the driver. > > The idea is to take the runtime pm handle on the device > whenever in use (reading values from the hardware or > using the trigger), and then use autosuspend to completely > shut it down (including regulators) when not in use. If the power-up > time for the sensor is long, then the autosuspend timeout > should be proportionally longer, like a magnitude or two above. > > With the proximity events I have this problem that I don't know > in the driver if someone had opened the file to read events > or not, only the core knows, I think. I just emit my events > and be happy. > > Jonathan: is there a way for the driver to know if someone > is listening on the event interface? Hmm. Normally we'd do it on someone actually enabling the events on the basis I'd expect userspace to open the file then enable the events. Nothing stops us doing it on file open I guess, but not sure what the real world benefit would be. > > > There is one problem I noticed, although I'm not sure if it is a problem > > in this driver. Reading one of the files in the sysfs results in: > > > > $ cat /sys/bus/iio/devices/iio\:device2/events/in_proximity_thresh_either_en > > Segmentation fault > > That looks like an ordinary bug, but that seems to be for the > core? Hm... Ah.. Seems I missed that you have the driver set event spec for enable, but didn't actually provide the callback function. + we clearly don't sanity check that one. Hence IIO core could do with hardening but driver is buggy as well. +static const struct iio_event_spec gp2ap002_events[] = { + { + .type = IIO_EV_TYPE_THRESH, + .dir = IIO_EV_DIR_EITHER, + .mask_separate = BIT(IIO_EV_INFO_ENABLE), + }, +}; Means you must supply read_event_config in iio_info. It's a bit odd if you don't also supply write event config for that matter though that wasn't the bug here. It would cause a similar bug if you wrote the sysfs file though :) Kind of also explains why my logic about enabling the event doesn't apply currently. Good find from Stephan on both fronts. Jonathan > > Yours, > Linus Walleij
diff --git a/MAINTAINERS b/MAINTAINERS index 1372b4139ebd..dbd4236fc7f5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -14893,6 +14893,14 @@ W: http://www.ibm.com/developerworks/linux/linux390/ S: Supported F: net/smc/ +SHARP GP2AP002A00F/GP2AP002S00F SENSOR DRIVER +M: Linus Walleij <linus.walleij@linaro.org> +L: linux-iio@vger.kernel.org +T: git git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git +S: Maintained +F: drivers/iio/light/gp2ap002.c +F: Documentation/devicetree/bindings/iio/light/sharp,gp2ap002.yaml + SHARP RJ54N1CB0C SENSOR DRIVER M: Jacopo Mondi <jacopo@jmondi.org> L: linux-media@vger.kernel.org diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig index 9968f982fbc7..307412c79c53 100644 --- a/drivers/iio/light/Kconfig +++ b/drivers/iio/light/Kconfig @@ -159,6 +159,17 @@ config IIO_CROS_EC_LIGHT_PROX To compile this driver as a module, choose M here: the module will be called cros_ec_light_prox. +config GP2AP002 + tristate "Sharp GP2AP002 Proximity/ALS sensor" + depends on I2C + select REGMAP + help + Say Y here if you have a Sharp GP2AP002 proximity/ALS combo-chip + hooked to an I2C bus. + + To compile this driver as a module, choose M here: the + module will be called gp2ap002. + config GP2AP020A00F tristate "Sharp GP2AP020A00F Proximity/ALS sensor" depends on I2C diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile index c98d1cefb861..264a76039006 100644 --- a/drivers/iio/light/Makefile +++ b/drivers/iio/light/Makefile @@ -18,6 +18,7 @@ obj-$(CONFIG_CM3323) += cm3323.o obj-$(CONFIG_CM3605) += cm3605.o obj-$(CONFIG_CM36651) += cm36651.o obj-$(CONFIG_IIO_CROS_EC_LIGHT_PROX) += cros_ec_light_prox.o +obj-$(CONFIG_GP2AP002) += gp2ap002.o obj-$(CONFIG_GP2AP020A00F) += gp2ap020a00f.o obj-$(CONFIG_HID_SENSOR_ALS) += hid-sensor-als.o obj-$(CONFIG_HID_SENSOR_PROX) += hid-sensor-prox.o diff --git a/drivers/iio/light/gp2ap002.c b/drivers/iio/light/gp2ap002.c new file mode 100644 index 000000000000..96016c3c03ef --- /dev/null +++ b/drivers/iio/light/gp2ap002.c @@ -0,0 +1,729 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * These are the two Sharp GP2AP002 variants supported by this driver: + * GP2AP002A00F Ambient Light and Proximity Sensor + * GP2AP002S00F Proximity Sensor + * + * Copyright (C) 2019 Linaro Ltd. + * Author: Linus Walleij <linus.walleij@linaro.org> + * + * Based partly on the code in Sony Ericssons GP2AP00200F driver by + * Courtney Cavin and Oskar Andero in drivers/input/misc/gp2ap002a00f.c + * Based partly on a Samsung misc driver submitted by + * Donggeun Kim & Minkyu Kang in 2011: + * https://lore.kernel.org/lkml/1315556546-7445-1-git-send-email-dg77.kim@samsung.com/ + * Based partly on a submission by + * Jonathan Bakker and Paweł Chmiel in january 2019: + * https://lore.kernel.org/linux-input/20190125175045.22576-1-pawel.mikolaj.chmiel@gmail.com/ + * Based partly on code from the Samsung GT-S7710 by <mjchen@sta.samsung.com> + * Based partly on the code in LG Electronics GP2AP00200F driver by + * Kenobi Lee <sungyoung.lee@lge.com> and EunYoung Cho <ey.cho@lge.com> + */ +#include <linux/module.h> +#include <linux/i2c.h> +#include <linux/regmap.h> +#include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> +#include <linux/iio/events.h> +#include <linux/iio/consumer.h> /* To get our ADC channel */ +#include <linux/iio/types.h> /* To deal with our ADC channel */ +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/regulator/consumer.h> +#include <linux/interrupt.h> +#include <linux/bits.h> +#include <linux/math64.h> +#include <linux/pm.h> + +#define GP2AP002_PROX_CHANNEL 0 +#define GP2AP002_ALS_CHANNEL 1 + +/* ------------------------------------------------------------------------ */ +/* ADDRESS SYMBOL DATA Init R/W */ +/* D7 D6 D5 D4 D3 D2 D1 D0 */ +/* ------------------------------------------------------------------------ */ +/* 0 PROX X X X X X X X VO H'00 R */ +/* 1 GAIN X X X X LED0 X X X H'00 W */ +/* 2 HYS HYSD HYSC1 HYSC0 X HYSF3 HYSF2 HYSF1 HYSF0 H'00 W */ +/* 3 CYCLE X X CYCL2 CYCL1 CYCL0 OSC2 X X H'00 W */ +/* 4 OPMOD X X X ASD X X VCON SSD H'00 W */ +/* 6 CON X X X OCON1 OCON0 X X X H'00 W */ +/* ------------------------------------------------------------------------ */ +/* VO :Proximity sensing result(0: no detection, 1: detection) */ +/* LED0 :Select switch for LED driver's On-registence(0:2x higher, 1:normal)*/ +/* HYSD/HYSF :Adjusts the receiver sensitivity */ +/* OSC :Select switch internal clocl frequency hoppling(0:effective) */ +/* CYCL :Determine the detection cycle(typically 8ms, up to 128x) */ +/* SSD :Software Shutdown function(0:shutdown, 1:operating) */ +/* VCON :VOUT output method control(0:normal, 1:interrupt) */ +/* ASD :Select switch for analog sleep function(0:ineffective, 1:effective)*/ +/* OCON :Select switch for enabling/disabling VOUT (00:enable, 11:disable) */ + +#define GP2AP002_PROX 0x00 +#define GP2AP002_GAIN 0x01 +#define GP2AP002_HYS 0x02 +#define GP2AP002_CYCLE 0x03 +#define GP2AP002_OPMOD 0x04 +#define GP2AP002_CON 0x06 + +#define GP2AP002_PROX_VO_DETECT BIT(0) + +/* Setting this bit to 0 means 2x higher LED resistance */ +#define GP2AP002_GAIN_LED_NORMAL BIT(3) + +/* + * These bits adjusts the proximity sensitivity, determining characteristics + * of the detection distance and its hysteresis. + */ +#define GP2AP002_HYS_HYSD_SHIFT 7 +#define GP2AP002_HYS_HYSD_MASK BIT(7) +#define GP2AP002_HYS_HYSC_SHIFT 5 +#define GP2AP002_HYS_HYSC_MASK GENMASK(6, 5) +#define GP2AP002_HYS_HYSF_SHIFT 0 +#define GP2AP002_HYS_HYSF_MASK GENMASK(3, 0) +#define GP2AP002_HYS_MASK (GP2AP002_HYS_HYSD_MASK | \ + GP2AP002_HYS_HYSC_MASK | \ + GP2AP002_HYS_HYSF_MASK) + +/* + * These values determine the detection cycle response time + * 0: 8ms, 1: 16ms, 2: 32ms, 3: 64ms, 4: 128ms, + * 5: 256ms, 6: 512ms, 7: 1024ms + */ +#define GP2AP002_CYCLE_CYCL_SHIFT 3 +#define GP2AP002_CYCLE_CYCL_MASK GENMASK(5, 3) + +/* + * Select switch for internal clock frequency hopping + * 0: effective, + * 1: ineffective + */ +#define GP2AP002_CYCLE_OSC_EFFECTIVE 0 +#define GP2AP002_CYCLE_OSC_INEFFECTIVE BIT(2) +#define GP2AP002_CYCLE_OSC_MASK BIT(2) + +/* Analog sleep effective */ +#define GP2AP002_OPMOD_ASD BIT(4) +/* Enable chip */ +#define GP2AP002_OPMOD_SSD_OPERATING BIT(0) +/* IRQ mode */ +#define GP2AP002_OPMOD_VCON_IRQ BIT(1) +#define GP2AP002_OPMOD_MASK (BIT(0) | BIT(1) | BIT(4)) + +/* + * Select switch for enabling/disabling Vout pin + * 0: enable + * 2: force to go Low + * 3: force to go High + */ +#define GP2AP002_CON_OCON_SHIFT 3 +#define GP2AP002_CON_OCON_ENABLE (0x0 << GP2AP002_CON_OCON_SHIFT) +#define GP2AP002_CON_OCON_LOW (0x2 << GP2AP002_CON_OCON_SHIFT) +#define GP2AP002_CON_OCON_HIGH (0x3 << GP2AP002_CON_OCON_SHIFT) +#define GP2AP002_CON_OCON_MASK (0x3 << GP2AP002_CON_OCON_SHIFT) + +/** + * struct gp2ap002 - GP2AP002 state + * @map: regmap pointer for the i2c regmap + * @dev: pointer to parent device + * @vdd: regulator controlling VDD + * @vio: regulator controlling VIO + * @alsout: IIO ADC channel to convert the ALSOUT signal + * @is_gp2ap002s00f: this is the GP2AP002F variant of the chip + */ +struct gp2ap002 { + struct regmap *map; + struct device *dev; + struct regulator *vdd; + struct regulator *vio; + struct iio_channel *alsout; + enum iio_event_direction dir; + u8 hys_far; + u8 hys_close; + bool is_gp2ap002s00f; +}; + +static irqreturn_t gp2ap002_prox_irq(int irq, void *d) +{ + struct iio_dev *indio_dev = d; + struct gp2ap002 *gp2ap002 = iio_priv(indio_dev); + u64 ev; + int val; + int ret; + + ret = regmap_read(gp2ap002->map, GP2AP002_PROX, &val); + if (ret) { + dev_err(gp2ap002->dev, "error reading proximity\n"); + goto err_retrig; + } + + if (val & GP2AP002_PROX_VO_DETECT) { + /* Close */ + dev_dbg(gp2ap002->dev, "close\n"); + ret = regmap_write(gp2ap002->map, GP2AP002_HYS, + gp2ap002->hys_far); + if (ret) + dev_err(gp2ap002->dev, + "error setting up proximity hysteresis\n"); + ev = IIO_UNMOD_EVENT_CODE(IIO_PROXIMITY, GP2AP002_PROX_CHANNEL, + IIO_EV_TYPE_THRESH, IIO_EV_DIR_RISING); + } else { + /* Far */ + dev_dbg(gp2ap002->dev, "far\n"); + ret = regmap_write(gp2ap002->map, GP2AP002_HYS, + gp2ap002->hys_close); + if (ret) + dev_err(gp2ap002->dev, + "error setting up proximity hysteresis\n"); + ev = IIO_UNMOD_EVENT_CODE(IIO_PROXIMITY, GP2AP002_PROX_CHANNEL, + IIO_EV_TYPE_THRESH, IIO_EV_DIR_FALLING); + } + iio_push_event(indio_dev, ev, iio_get_time_ns(indio_dev)); + + /* + * After changing hysteresis, we need to wait for one detection + * cycle to see if anything changed, or we will just trigger the + * previous interrupt again. A detection cycle depends on the CYCLE + * register, we are hard-coding ~8 ms in probe() so wait some more + * than this, 20-30 ms. + */ + usleep_range(20000, 30000); + +err_retrig: + ret = regmap_write(gp2ap002->map, GP2AP002_CON, + GP2AP002_CON_OCON_ENABLE); + if (ret) + dev_err(gp2ap002->dev, "error setting up VOUT control\n"); + + return IRQ_HANDLED; +} + +struct gp2ap002_illuminance { + unsigned int curr; + unsigned int lux; +}; + +/* + * This array maps current and lux. + * + * Ambient light sensing range is 3 to 55000 lux. + * + * This mapping is based on the following formula. + * illuminance = 10 ^ (current / 10) + */ +static const struct gp2ap002_illuminance gp2ap002_illuminance_table[] = { + { .curr = 5, .lux = 3 }, + { .curr = 6, .lux = 4 }, + { .curr = 7, .lux = 5 }, + { .curr = 8, .lux = 6 }, + { .curr = 9, .lux = 8 }, + { .curr = 10, .lux = 10 }, + { .curr = 11, .lux = 12 }, + { .curr = 12, .lux = 16 }, + { .curr = 13, .lux = 20 }, + { .curr = 14, .lux = 25 }, + { .curr = 15, .lux = 32 }, + { .curr = 16, .lux = 40 }, + { .curr = 17, .lux = 50 }, + { .curr = 18, .lux = 63 }, + { .curr = 19, .lux = 79 }, + { .curr = 20, .lux = 100 }, + { .curr = 21, .lux = 126 }, + { .curr = 22, .lux = 158 }, + { .curr = 23, .lux = 200 }, + { .curr = 24, .lux = 251 }, + { .curr = 25, .lux = 316 }, + { .curr = 26, .lux = 398 }, + { .curr = 27, .lux = 501 }, + { .curr = 28, .lux = 631 }, + { .curr = 29, .lux = 794 }, + { .curr = 30, .lux = 1000 }, + { .curr = 31, .lux = 1259 }, + { .curr = 32, .lux = 1585 }, + { .curr = 33, .lux = 1995 }, + { .curr = 34, .lux = 2512 }, + { .curr = 35, .lux = 3162 }, + { .curr = 36, .lux = 3981 }, + { .curr = 37, .lux = 5012 }, + { .curr = 38, .lux = 6310 }, + { .curr = 39, .lux = 7943 }, + { .curr = 40, .lux = 10000 }, + { .curr = 41, .lux = 12589 }, + { .curr = 42, .lux = 15849 }, + { .curr = 43, .lux = 19953 }, + { .curr = 44, .lux = 25119 }, + { .curr = 45, .lux = 31623 }, + { .curr = 46, .lux = 39811 }, + { .curr = 47, .lux = 50119 }, +}; + +static int gp2ap002_get_lux(struct gp2ap002 *gp2ap002) +{ + const struct gp2ap002_illuminance *ill1; + const struct gp2ap002_illuminance *ill2; + int ret, res; + int i; + + ret = iio_read_channel_processed(gp2ap002->alsout, &res); + if (ret < 0) + return ret; + + dev_dbg(gp2ap002->dev, "read %d mA from ADC\n", res); + + ill1 = &gp2ap002_illuminance_table[0]; + if (res < ill1->curr) { + dev_dbg(gp2ap002->dev, "total darkness\n"); + return 0; + } + for (i = 0; i < ARRAY_SIZE(gp2ap002_illuminance_table) - 1; i++) { + ill1 = &gp2ap002_illuminance_table[i]; + ill2 = &gp2ap002_illuminance_table[i + 1]; + + if (res > ill2->curr) + continue; + if ((res <= ill1->curr) && (res >= ill2->curr)) + break; + } + if (res > ill2->curr) { + dev_info_once(gp2ap002->dev, "max current overflow\n"); + return ill2->curr; + } + /* Interpolate and return */ + dev_dbg(gp2ap002->dev, "interpolate index %d and %d\n", i, i + 1); + /* How many steps along the curve */ + i = res - ill1->curr; /* x - x0 */ + /* Linear interpolation */ + return ill1->lux + i * + ((ill2->lux - ill1->lux) / (ill2->curr - ill1->curr)); +} + +static int gp2ap002_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + struct gp2ap002 *gp2ap002 = iio_priv(indio_dev); + int ret; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + switch (chan->type) { + case IIO_LIGHT: + ret = gp2ap002_get_lux(gp2ap002); + if (ret < 0) + return ret; + *val = ret; + return IIO_VAL_INT; + default: + return -EINVAL; + } + default: + return -EINVAL; + } +} + +static const struct iio_info gp2ap002_info = { + .read_raw = gp2ap002_read_raw, +}; + +static const struct iio_event_spec gp2ap002_events[] = { + { + .type = IIO_EV_TYPE_THRESH, + .dir = IIO_EV_DIR_EITHER, + .mask_separate = BIT(IIO_EV_INFO_ENABLE), + }, +}; + +static const struct iio_chan_spec gp2ap002_channels[] = { + { + .type = IIO_PROXIMITY, + .event_spec = gp2ap002_events, + .num_event_specs = ARRAY_SIZE(gp2ap002_events), + }, + { + .type = IIO_LIGHT, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + .channel = GP2AP002_ALS_CHANNEL, + }, +}; + +/* + * We need a special regmap because this hardware expects to + * write single bytes to registers but read a 16bit word on some + * variants and discard the lower 8 bits so combine + * i2c_smbus_read_word_data() with i2c_smbus_write_byte_data() + * selectively like this. + */ +static int gp2ap002a00f_regmap_i2c_read(void *context, unsigned int reg, + unsigned int *val) +{ + struct device *dev = context; + struct i2c_client *i2c = to_i2c_client(dev); + int ret; + + ret = i2c_smbus_read_byte_data(i2c, reg); + if (ret < 0) + return ret; + *val = ret & 0xff; + + return 0; +} + +static int gp2ap002s00f_regmap_i2c_read(void *context, unsigned int reg, + unsigned int *val) +{ + struct device *dev = context; + struct i2c_client *i2c = to_i2c_client(dev); + int ret; + + ret = i2c_smbus_read_word_data(i2c, reg); + if (ret < 0) + return ret; + + *val = (ret >> 8) & 0xFF; + + return 0; +} + +static int gp2ap002_regmap_i2c_write(void *context, unsigned int reg, + unsigned int val) +{ + struct device *dev = context; + struct i2c_client *i2c = to_i2c_client(dev); + + return i2c_smbus_write_byte_data(i2c, reg, val); +} + +static struct regmap_bus gp2ap002a00f_regmap_bus = { + .reg_read = gp2ap002a00f_regmap_i2c_read, + .reg_write = gp2ap002_regmap_i2c_write, +}; + +static struct regmap_bus gp2ap002s00f_regmap_bus = { + .reg_read = gp2ap002s00f_regmap_i2c_read, + .reg_write = gp2ap002_regmap_i2c_write, +}; + +static int gp2ap002_init(struct gp2ap002 *gp2ap002) +{ + int ret; + + /* Set up the IR LED resistance */ + ret = regmap_write(gp2ap002->map, GP2AP002_GAIN, + GP2AP002_GAIN_LED_NORMAL); + if (ret) { + dev_err(gp2ap002->dev, "error setting up LED gain\n"); + return ret; + } + ret = regmap_write(gp2ap002->map, GP2AP002_HYS, gp2ap002->hys_far); + if (ret) { + dev_err(gp2ap002->dev, + "error setting up proximity hysteresis\n"); + return ret; + } + + /* Disable internal frequency hopping */ + ret = regmap_write(gp2ap002->map, GP2AP002_CYCLE, + GP2AP002_CYCLE_OSC_INEFFECTIVE); + if (ret) { + dev_err(gp2ap002->dev, + "error setting up internal frequency hopping\n"); + return ret; + } + + /* Enable chip and IRQ, disable analog sleep */ + ret = regmap_write(gp2ap002->map, GP2AP002_OPMOD, + GP2AP002_OPMOD_SSD_OPERATING | + GP2AP002_OPMOD_VCON_IRQ); + if (ret) { + dev_err(gp2ap002->dev, "error setting up operation mode\n"); + return ret; + } + + /* Interrupt on VOUT enabled */ + ret = regmap_write(gp2ap002->map, GP2AP002_CON, + GP2AP002_CON_OCON_ENABLE); + if (ret) + dev_err(gp2ap002->dev, "error setting up VOUT control\n"); + + return ret; +} + +static int gp2ap002_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct gp2ap002 *gp2ap002; + struct iio_dev *indio_dev; + struct device *dev = &client->dev; + enum iio_chan_type ch_type; + static const struct regmap_config config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = GP2AP002_CON, + }; + struct regmap_bus *rbus; + struct regmap *regmap; + int num_chan; + const char *compat; + u8 val; + int ret; + + indio_dev = devm_iio_device_alloc(dev, sizeof(*gp2ap002)); + if (!indio_dev) + return -ENOMEM; + i2c_set_clientdata(client, indio_dev); + + gp2ap002 = iio_priv(indio_dev); + gp2ap002->dev = dev; + + /* + * Check the device compatible like this makes it possible to use + * ACPI PRP0001 for registering the sensor using device tree + * properties. + */ + ret = device_property_read_string(dev, "compatible", &compat); + if (ret) { + dev_err(dev, "cannot check compatible\n"); + return ret; + } + gp2ap002->is_gp2ap002s00f = !strcmp(compat, "sharp,gp2ap002s00f"); + + if (gp2ap002->is_gp2ap002s00f) + rbus = &gp2ap002s00f_regmap_bus; + else + rbus = &gp2ap002a00f_regmap_bus; + + regmap = devm_regmap_init(dev, rbus, dev, &config); + if (IS_ERR(regmap)) { + dev_err(dev, "Failed to register i2c regmap %d\n", + (int)PTR_ERR(regmap)); + return PTR_ERR(regmap); + } + gp2ap002->map = regmap; + + /* + * The hysteresis settings are coded into the device tree as values + * to be written into the hysteresis register. The datasheet defines + * modes "A", "B1" and "B2" with fixed values to be use but vendor + * code trees for actual devices are tweaking these values and refer to + * modes named things like "B1.5". To be able to support any devices, + * we allow passing an arbitrary hysteresis setting for "near" and + * "far". + */ + + /* Check the device tree for the IR LED hysteresis */ + ret = device_property_read_u8(dev, "sharp,proximity-far-hysteresis", + &val); + if (ret) { + dev_err(dev, "failed to obtain proximity far setting\n"); + return ret; + } + dev_dbg(dev, "proximity far setting %02x\n", val); + gp2ap002->hys_far = val; + + ret = device_property_read_u8(dev, "sharp,proximity-close-hysteresis", + &val); + if (ret) { + dev_err(dev, "failed to obtain proximity close setting\n"); + return ret; + } + dev_dbg(dev, "proximity close setting %02x\n", val); + gp2ap002->hys_close = val; + + /* The GP2AP002A00F has a light sensor too */ + if (!gp2ap002->is_gp2ap002s00f) { + gp2ap002->alsout = devm_iio_channel_get(dev, "alsout"); + if (IS_ERR(gp2ap002->alsout)) { + if (PTR_ERR(gp2ap002->alsout) == -ENODEV) { + dev_err(dev, "no ADC, deferring...\n"); + return -EPROBE_DEFER; + } + dev_err(dev, "failed to get ALSOUT ADC channel\n"); + return PTR_ERR(gp2ap002->alsout); + } + ret = iio_get_channel_type(gp2ap002->alsout, &ch_type); + if (ret < 0) + return ret; + if (ch_type != IIO_CURRENT) { + dev_err(dev, + "wrong type of IIO channel specified for ALSOUT\n"); + return -EINVAL; + } + } + + gp2ap002->vdd = devm_regulator_get(dev, "vdd"); + if (IS_ERR(gp2ap002->vdd)) { + dev_err(dev, "failed to get VDD regulator\n"); + return PTR_ERR(gp2ap002->vdd); + } + gp2ap002->vio = devm_regulator_get(dev, "vio"); + if (IS_ERR(gp2ap002->vio)) { + dev_err(dev, "failed to get VIO regulator\n"); + return PTR_ERR(gp2ap002->vio); + } + + /* Operating voltage 2.4V .. 3.6V according to datasheet */ + ret = regulator_set_voltage(gp2ap002->vdd, 2400000, 3600000); + if (ret) { + dev_err(dev, "failed to sett VDD voltage\n"); + return ret; + } + + /* VIO should be between 1.65V and VDD */ + ret = regulator_get_voltage(gp2ap002->vdd); + if (ret < 0) { + dev_err(dev, "failed to get VIO voltage\n"); + return ret; + } + ret = regulator_set_voltage(gp2ap002->vio, 1650000, ret); + if (ret) { + dev_err(dev, "failed to set VIO voltage\n"); + return ret; + } + + ret = regulator_enable(gp2ap002->vdd); + if (ret) { + dev_err(dev, "failed to enable VDD regulator\n"); + return ret; + } + ret = regulator_enable(gp2ap002->vio); + if (ret) { + dev_err(dev, "failed to enable VIO regulator\n"); + goto out_disable_vdd; + } + + msleep(20); + + ret = gp2ap002_init(gp2ap002); + if (ret) { + dev_err(dev, "initialization failed\n"); + goto out_disable_vio; + } + + ret = devm_request_threaded_irq(dev, client->irq, NULL, + gp2ap002_prox_irq, IRQF_ONESHOT, + "gp2ap002", indio_dev); + if (ret) { + dev_err(dev, "unable to request IRQ\n"); + goto out_disable_vio; + } + + indio_dev->dev.parent = dev; + indio_dev->info = &gp2ap002_info; + indio_dev->name = "gp2ap002"; + indio_dev->channels = gp2ap002_channels; + /* Skip light channel for the proximity-only sensor */ + num_chan = ARRAY_SIZE(gp2ap002_channels); + if (gp2ap002->is_gp2ap002s00f) + num_chan--; + indio_dev->num_channels = num_chan; + indio_dev->modes = INDIO_DIRECT_MODE; + + ret = iio_device_register(indio_dev); + if (ret) + goto out_disable_vio; + dev_dbg(dev, "Sharp GP2AP002 probed successfully\n"); + + return 0; + +out_disable_vio: + regulator_disable(gp2ap002->vio); +out_disable_vdd: + regulator_disable(gp2ap002->vdd); + return ret; +} + +static int gp2ap002_remove(struct i2c_client *client) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(client); + struct gp2ap002 *gp2ap002 = iio_priv(indio_dev); + + iio_device_unregister(indio_dev); + regulator_disable(gp2ap002->vio); + regulator_disable(gp2ap002->vdd); + + return 0; +} + +static int __maybe_unused gp2ap002_pm_suspend(struct device *dev) +{ + struct iio_dev *indio_dev = dev_get_drvdata(dev); + struct gp2ap002 *gp2ap002 = iio_priv(indio_dev); + int ret; + + /* Disable chip and IRQ, everything off */ + ret = regmap_write(gp2ap002->map, GP2AP002_OPMOD, 0x00); + if (ret) { + dev_err(gp2ap002->dev, "error setting up operation mode\n"); + return ret; + } + /* + * As these regulators may be shared, at least we are now in + * sleep even if the regulators aren't really turned off. + */ + regulator_disable(gp2ap002->vio); + regulator_disable(gp2ap002->vdd); + + return 0; +} + +static int __maybe_unused gp2ap002_pm_resume(struct device *dev) +{ + struct iio_dev *indio_dev = dev_get_drvdata(dev); + struct gp2ap002 *gp2ap002 = iio_priv(indio_dev); + int ret; + + ret = regulator_enable(gp2ap002->vdd); + if (ret) { + dev_err(dev, "failed to enable VDD regulator in resume path\n"); + return ret; + } + ret = regulator_enable(gp2ap002->vio); + if (ret) { + dev_err(dev, "failed to enable VIO regulator in resume path\n"); + return ret; + } + + msleep(20); + + ret = gp2ap002_init(gp2ap002); + if (ret) { + dev_err(dev, "re-initialization failed\n"); + return ret; + } + + return 0; +} + +static const struct dev_pm_ops gp2ap002_dev_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(gp2ap002_pm_suspend, + gp2ap002_pm_resume) +}; + +static const struct i2c_device_id gp2ap002_id_table[] = { + { "gp2ap002", 0 }, + { }, +}; +MODULE_DEVICE_TABLE(i2c, gp2ap002_id); + +static const struct of_device_id gp2ap002_of_match[] = { + { .compatible = "sharp,gp2ap002a00f" }, + { .compatible = "sharp,gp2ap002s00f" }, + { }, +}; +MODULE_DEVICE_TABLE(of, gp2ap002_of_match); + +static struct i2c_driver gp2ap002_driver = { + .driver = { + .name = "gp2ap002", + .of_match_table = gp2ap002_of_match, + .pm = &gp2ap002_dev_pm_ops, + }, + .probe = gp2ap002_probe, + .remove = gp2ap002_remove, + .id_table = gp2ap002_id_table, +}; +module_i2c_driver(gp2ap002_driver); + +MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>"); +MODULE_DESCRIPTION("GP2AP002 ambient light and proximity sensor driver"); +MODULE_LICENSE("GPL v2");
This driver handles two different Sharp sensors that have been proposed for merging to the mainline kernel over the years, and already has a limited proximity-only driver in the input subsystem. These components are completely different from the confusingly similarly named Sharp GP2AP020A00F, for which we have a driver in drivers/iio/light/gp2ap020a00f.c The two components GP2AP002A00F and GP2AP002S00F are distinctively different but similar: they share the same set of registers but differ slightly in the I2C protocol. Instead of the approach by the previous input driver, we create a combined IIO proximity and light sensor driver. The plan is to merge this driver and delete the input driver. The pieces for the driver are picked all over the place after researching and grepping through a few different vendor trees and driver submissions. We merge it under the light sensors because: - It has similarities with the Capella CM3605 light sensor and proximity driver which is there. - It is related to the GP2AP020A00F driver which is also there. This driver was tested with the Samsung GT-S7710 mobile phone which has the GP2AP002S00F proximity sensor mounted. Cc: Stephan Gerhold <stephan@gerhold.net> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Cc: Jonathan Bakker <xc-racer2@live.ca> Cc: Oskar Andero <oskar.andero@gmail.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v3->v4: - Realized I had to fix also the last two users of of_property_read_u32(). Replaced with device_property_read_u8(). Dropped unsigned byte check because it can't be anything else. - Change warnings about properties to "failed to obtain.." - Return the actual error code instead of -EINVAL - Move interpolation message to dev_dbg() - Return with error if we fail to enable regulators on the resume path. ChangeLog v2->v3: - Use the device property accessors to read the compatible string and drop the dependency on <linux/of.h> making the driver reusable with ACPI. - Add a paragraph with comments on the hysteresis values. ChangeLog v1->v2: - Drop ifdef CONFIG_OF and of_match_ptr() to encourage reuse with other OF-compliant hardware descriptions such as ACPI PRP001 - Convert success print to dev_dbg() - Drop leftover debug read of VDD voltage - Create two different regmap buses for the two component variants and select the one we want depending on detected component - Use if (ret) on all regmap accesses - Fix up error handling in interrupt routine for proximity - Provide some rationale for the 20-30 ms delay in the irq handler - Use GENMASK() where applicable - Prefix all defines with GP2AP002_* - Drop buffer infrastructure from Kconfig - Staticize gp2ap002_illuminance_table --- MAINTAINERS | 8 + drivers/iio/light/Kconfig | 11 + drivers/iio/light/Makefile | 1 + drivers/iio/light/gp2ap002.c | 729 +++++++++++++++++++++++++++++++++++ 4 files changed, 749 insertions(+) create mode 100644 drivers/iio/light/gp2ap002.c