Message ID | 20200102131845.12992-8-t-kristo@ti.com (mailing list archive) |
---|---|
State | Superseded |
Headers | show |
Series | remoteproc: updates for omap remoteproc support | expand |
Hi Tero, On 1/2/20 7:18 AM, Tero Kristo wrote: > From: Suman Anna <s-anna@ti.com> > > DRA7xx/AM57xx SoCs have two IPU and up to two DSP processor subsystems > for offloading different computation algorithms. The IPU processor > subsystem contains dual-core ARM Cortex-M4 processors, and is very > similar to those on OMAP5. The DSP processor subsystem is based on > the TI's standard TMS320C66x DSP CorePac core. > > Support has been added to the OMAP remoteproc driver through new > DRA7xx specific compatibles for properly probing and booting all > the different processor subsystem instances on DRA7xx/AM57xx > SoCs - IPU1, IPU2, DSP1 & DSP2. A build dependency with SOC_DRA7XX > is added to enable the driver to be built in DRA7xx-only configuration. > > The DSP boot address programming needed enhancement for DRA7xx as the > boot register fields are different on DRA7 compared to OMAP4 and OMAP5 > SoCs. The register on DRA7xx contains additional fields within the > register and the boot address bit-field is right-shifted by 10 bits. > The internal memory parsing logic has also been updated to compute > the device addresses for the L2 RAM for DSP devices using relative > addressing logic, and to parse two additional RAMs at L1 level - L1P > and L1D. This allows the remoteproc driver to support loading into > these regions for a small subset of firmware images requiring as > such. The most common usage would be to use the L1 programmable > RAMs as L1 Caches. > > The firmware lookup logic also has to be adjusted for DRA7xx as > there are (can be) more than one instance of both the IPU and DSP > remote processors for the first time in OMAP4+ SoCs. > > Signed-off-by: Suman Anna <s-anna@ti.com> > [t-kristo@ti.com: moved address translation quirks to pdata] > Signed-off-by: Tero Kristo <t-kristo@ti.com> > --- > v4: > - data format change due to device data changes to mem layout > > drivers/remoteproc/Kconfig | 2 +- > drivers/remoteproc/omap_remoteproc.c | 38 +++++++++++++++++++++++++++- > 2 files changed, 38 insertions(+), 2 deletions(-) > > diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig > index 94afdde4bc9f..d6450d7fcf92 100644 > --- a/drivers/remoteproc/Kconfig > +++ b/drivers/remoteproc/Kconfig > @@ -25,7 +25,7 @@ config IMX_REMOTEPROC > > config OMAP_REMOTEPROC > tristate "OMAP remoteproc support" > - depends on ARCH_OMAP4 || SOC_OMAP5 > + depends on ARCH_OMAP4 || SOC_OMAP5 || SOC_DRA7XX > depends on OMAP_IOMMU > select MAILBOX > select OMAP2PLUS_MBOX > diff --git a/drivers/remoteproc/omap_remoteproc.c b/drivers/remoteproc/omap_remoteproc.c > index 8a6dd742a8b1..9140c528c416 100644 > --- a/drivers/remoteproc/omap_remoteproc.c > +++ b/drivers/remoteproc/omap_remoteproc.c > @@ -34,10 +34,13 @@ > * struct omap_rproc_boot_data - boot data structure for the DSP omap rprocs > * @syscon: regmap handle for the system control configuration module > * @boot_reg: boot register offset within the @syscon regmap > + * @boot_reg_shift: bit-field shift required for the boot address value in > + * @boot_reg > */ > struct omap_rproc_boot_data { > struct regmap *syscon; > unsigned int boot_reg; > + unsigned int boot_reg_shift; > }; > > /** > @@ -159,6 +162,8 @@ static int omap_rproc_write_dsp_boot_addr(struct rproc *rproc) > struct omap_rproc *oproc = rproc->priv; > struct omap_rproc_boot_data *bdata = oproc->boot_data; > u32 offset = bdata->boot_reg; > + u32 value; > + u32 mask; > > if (rproc->bootaddr & (SZ_1K - 1)) { > dev_err(dev, "invalid boot address 0x%x, must be aligned on a 1KB boundary\n", > @@ -166,7 +171,10 @@ static int omap_rproc_write_dsp_boot_addr(struct rproc *rproc) > return -EINVAL; > } > > - regmap_write(bdata->syscon, offset, rproc->bootaddr); > + value = rproc->bootaddr >> bdata->boot_reg_shift; > + mask = ~(SZ_1K - 1) >> bdata->boot_reg_shift; > + > + regmap_update_bits(bdata->syscon, offset, mask, value); > > return 0; > } > @@ -296,6 +304,13 @@ static const struct omap_rproc_mem_data ipu_mems[] = { > { }, > }; > > +static const struct omap_rproc_mem_data dra7_dsp_mems[] = { > + { .name = "l2ram", .dev_addr = 0x800000 }, > + { .name = "l1pram", .dev_addr = 0xe00000 }, > + { .name = "l1dram", .dev_addr = 0xf00000 }, > + { }, > +}; > + > static const struct omap_rproc_dev_data omap4_dsp_dev_data = { > .device_name = "dsp", > }; > @@ -314,6 +329,16 @@ static const struct omap_rproc_dev_data omap5_ipu_dev_data = { > .mems = ipu_mems, > }; > > +static const struct omap_rproc_dev_data dra7_dsp_dev_data = { > + .device_name = "dsp", > + .mems = dra7_dsp_mems, > +}; > + > +static const struct omap_rproc_dev_data dra7_ipu_dev_data = { > + .device_name = "ipu", > + .mems = ipu_mems, > +}; > + > static const struct of_device_id omap_rproc_of_match[] = { > { > .compatible = "ti,omap4-dsp", > @@ -331,6 +356,14 @@ static const struct of_device_id omap_rproc_of_match[] = { > .compatible = "ti,omap5-ipu", > .data = &omap5_ipu_dev_data, > }, > + { > + .compatible = "ti,dra7-dsp", > + .data = &dra7_dsp_dev_data, > + }, > + { > + .compatible = "ti,dra7-ipu", > + .data = &dra7_ipu_dev_data, > + }, > { > /* end */ > }, > @@ -383,6 +416,9 @@ static int omap_rproc_get_boot_data(struct platform_device *pdev, > return -EINVAL; > } > > + of_property_read_u32(np, "ti,bootreg-shift", > + &oproc->boot_data->boot_reg_shift); Missing error checks, guess you will have to change this anyway when you address Rob's comments. regards Suman > + > return 0; > } > >
On 08/01/2020 21:39, Suman Anna wrote: > Hi Tero, > > On 1/2/20 7:18 AM, Tero Kristo wrote: >> From: Suman Anna <s-anna@ti.com> >> >> DRA7xx/AM57xx SoCs have two IPU and up to two DSP processor subsystems >> for offloading different computation algorithms. The IPU processor >> subsystem contains dual-core ARM Cortex-M4 processors, and is very >> similar to those on OMAP5. The DSP processor subsystem is based on >> the TI's standard TMS320C66x DSP CorePac core. >> >> Support has been added to the OMAP remoteproc driver through new >> DRA7xx specific compatibles for properly probing and booting all >> the different processor subsystem instances on DRA7xx/AM57xx >> SoCs - IPU1, IPU2, DSP1 & DSP2. A build dependency with SOC_DRA7XX >> is added to enable the driver to be built in DRA7xx-only configuration. >> >> The DSP boot address programming needed enhancement for DRA7xx as the >> boot register fields are different on DRA7 compared to OMAP4 and OMAP5 >> SoCs. The register on DRA7xx contains additional fields within the >> register and the boot address bit-field is right-shifted by 10 bits. >> The internal memory parsing logic has also been updated to compute >> the device addresses for the L2 RAM for DSP devices using relative >> addressing logic, and to parse two additional RAMs at L1 level - L1P >> and L1D. This allows the remoteproc driver to support loading into >> these regions for a small subset of firmware images requiring as >> such. The most common usage would be to use the L1 programmable >> RAMs as L1 Caches. >> >> The firmware lookup logic also has to be adjusted for DRA7xx as >> there are (can be) more than one instance of both the IPU and DSP >> remote processors for the first time in OMAP4+ SoCs. >> >> Signed-off-by: Suman Anna <s-anna@ti.com> >> [t-kristo@ti.com: moved address translation quirks to pdata] >> Signed-off-by: Tero Kristo <t-kristo@ti.com> >> --- >> v4: >> - data format change due to device data changes to mem layout >> >> drivers/remoteproc/Kconfig | 2 +- >> drivers/remoteproc/omap_remoteproc.c | 38 +++++++++++++++++++++++++++- >> 2 files changed, 38 insertions(+), 2 deletions(-) >> >> diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig >> index 94afdde4bc9f..d6450d7fcf92 100644 >> --- a/drivers/remoteproc/Kconfig >> +++ b/drivers/remoteproc/Kconfig >> @@ -25,7 +25,7 @@ config IMX_REMOTEPROC >> >> config OMAP_REMOTEPROC >> tristate "OMAP remoteproc support" >> - depends on ARCH_OMAP4 || SOC_OMAP5 >> + depends on ARCH_OMAP4 || SOC_OMAP5 || SOC_DRA7XX >> depends on OMAP_IOMMU >> select MAILBOX >> select OMAP2PLUS_MBOX >> diff --git a/drivers/remoteproc/omap_remoteproc.c b/drivers/remoteproc/omap_remoteproc.c >> index 8a6dd742a8b1..9140c528c416 100644 >> --- a/drivers/remoteproc/omap_remoteproc.c >> +++ b/drivers/remoteproc/omap_remoteproc.c >> @@ -34,10 +34,13 @@ >> * struct omap_rproc_boot_data - boot data structure for the DSP omap rprocs >> * @syscon: regmap handle for the system control configuration module >> * @boot_reg: boot register offset within the @syscon regmap >> + * @boot_reg_shift: bit-field shift required for the boot address value in >> + * @boot_reg >> */ >> struct omap_rproc_boot_data { >> struct regmap *syscon; >> unsigned int boot_reg; >> + unsigned int boot_reg_shift; >> }; >> >> /** >> @@ -159,6 +162,8 @@ static int omap_rproc_write_dsp_boot_addr(struct rproc *rproc) >> struct omap_rproc *oproc = rproc->priv; >> struct omap_rproc_boot_data *bdata = oproc->boot_data; >> u32 offset = bdata->boot_reg; >> + u32 value; >> + u32 mask; >> >> if (rproc->bootaddr & (SZ_1K - 1)) { >> dev_err(dev, "invalid boot address 0x%x, must be aligned on a 1KB boundary\n", >> @@ -166,7 +171,10 @@ static int omap_rproc_write_dsp_boot_addr(struct rproc *rproc) >> return -EINVAL; >> } >> >> - regmap_write(bdata->syscon, offset, rproc->bootaddr); >> + value = rproc->bootaddr >> bdata->boot_reg_shift; >> + mask = ~(SZ_1K - 1) >> bdata->boot_reg_shift; >> + >> + regmap_update_bits(bdata->syscon, offset, mask, value); >> >> return 0; >> } >> @@ -296,6 +304,13 @@ static const struct omap_rproc_mem_data ipu_mems[] = { >> { }, >> }; >> >> +static const struct omap_rproc_mem_data dra7_dsp_mems[] = { >> + { .name = "l2ram", .dev_addr = 0x800000 }, >> + { .name = "l1pram", .dev_addr = 0xe00000 }, >> + { .name = "l1dram", .dev_addr = 0xf00000 }, >> + { }, >> +}; >> + >> static const struct omap_rproc_dev_data omap4_dsp_dev_data = { >> .device_name = "dsp", >> }; >> @@ -314,6 +329,16 @@ static const struct omap_rproc_dev_data omap5_ipu_dev_data = { >> .mems = ipu_mems, >> }; >> >> +static const struct omap_rproc_dev_data dra7_dsp_dev_data = { >> + .device_name = "dsp", >> + .mems = dra7_dsp_mems, >> +}; >> + >> +static const struct omap_rproc_dev_data dra7_ipu_dev_data = { >> + .device_name = "ipu", >> + .mems = ipu_mems, >> +}; >> + >> static const struct of_device_id omap_rproc_of_match[] = { >> { >> .compatible = "ti,omap4-dsp", >> @@ -331,6 +356,14 @@ static const struct of_device_id omap_rproc_of_match[] = { >> .compatible = "ti,omap5-ipu", >> .data = &omap5_ipu_dev_data, >> }, >> + { >> + .compatible = "ti,dra7-dsp", >> + .data = &dra7_dsp_dev_data, >> + }, >> + { >> + .compatible = "ti,dra7-ipu", >> + .data = &dra7_ipu_dev_data, >> + }, >> { >> /* end */ >> }, >> @@ -383,6 +416,9 @@ static int omap_rproc_get_boot_data(struct platform_device *pdev, >> return -EINVAL; >> } >> >> + of_property_read_u32(np, "ti,bootreg-shift", >> + &oproc->boot_data->boot_reg_shift); > > Missing error checks, guess you will have to change this anyway when you > address Rob's comments. This one is actually intentional. The only expected failure is missing the ti,bootreg-shift, but even this is a valid situation; we will just use bootreg shift value of zero (boot-data is zero initialized.) -Tero > > regards > Suman > >> + >> return 0; >> } >> >> > -- Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig index 94afdde4bc9f..d6450d7fcf92 100644 --- a/drivers/remoteproc/Kconfig +++ b/drivers/remoteproc/Kconfig @@ -25,7 +25,7 @@ config IMX_REMOTEPROC config OMAP_REMOTEPROC tristate "OMAP remoteproc support" - depends on ARCH_OMAP4 || SOC_OMAP5 + depends on ARCH_OMAP4 || SOC_OMAP5 || SOC_DRA7XX depends on OMAP_IOMMU select MAILBOX select OMAP2PLUS_MBOX diff --git a/drivers/remoteproc/omap_remoteproc.c b/drivers/remoteproc/omap_remoteproc.c index 8a6dd742a8b1..9140c528c416 100644 --- a/drivers/remoteproc/omap_remoteproc.c +++ b/drivers/remoteproc/omap_remoteproc.c @@ -34,10 +34,13 @@ * struct omap_rproc_boot_data - boot data structure for the DSP omap rprocs * @syscon: regmap handle for the system control configuration module * @boot_reg: boot register offset within the @syscon regmap + * @boot_reg_shift: bit-field shift required for the boot address value in + * @boot_reg */ struct omap_rproc_boot_data { struct regmap *syscon; unsigned int boot_reg; + unsigned int boot_reg_shift; }; /** @@ -159,6 +162,8 @@ static int omap_rproc_write_dsp_boot_addr(struct rproc *rproc) struct omap_rproc *oproc = rproc->priv; struct omap_rproc_boot_data *bdata = oproc->boot_data; u32 offset = bdata->boot_reg; + u32 value; + u32 mask; if (rproc->bootaddr & (SZ_1K - 1)) { dev_err(dev, "invalid boot address 0x%x, must be aligned on a 1KB boundary\n", @@ -166,7 +171,10 @@ static int omap_rproc_write_dsp_boot_addr(struct rproc *rproc) return -EINVAL; } - regmap_write(bdata->syscon, offset, rproc->bootaddr); + value = rproc->bootaddr >> bdata->boot_reg_shift; + mask = ~(SZ_1K - 1) >> bdata->boot_reg_shift; + + regmap_update_bits(bdata->syscon, offset, mask, value); return 0; } @@ -296,6 +304,13 @@ static const struct omap_rproc_mem_data ipu_mems[] = { { }, }; +static const struct omap_rproc_mem_data dra7_dsp_mems[] = { + { .name = "l2ram", .dev_addr = 0x800000 }, + { .name = "l1pram", .dev_addr = 0xe00000 }, + { .name = "l1dram", .dev_addr = 0xf00000 }, + { }, +}; + static const struct omap_rproc_dev_data omap4_dsp_dev_data = { .device_name = "dsp", }; @@ -314,6 +329,16 @@ static const struct omap_rproc_dev_data omap5_ipu_dev_data = { .mems = ipu_mems, }; +static const struct omap_rproc_dev_data dra7_dsp_dev_data = { + .device_name = "dsp", + .mems = dra7_dsp_mems, +}; + +static const struct omap_rproc_dev_data dra7_ipu_dev_data = { + .device_name = "ipu", + .mems = ipu_mems, +}; + static const struct of_device_id omap_rproc_of_match[] = { { .compatible = "ti,omap4-dsp", @@ -331,6 +356,14 @@ static const struct of_device_id omap_rproc_of_match[] = { .compatible = "ti,omap5-ipu", .data = &omap5_ipu_dev_data, }, + { + .compatible = "ti,dra7-dsp", + .data = &dra7_dsp_dev_data, + }, + { + .compatible = "ti,dra7-ipu", + .data = &dra7_ipu_dev_data, + }, { /* end */ }, @@ -383,6 +416,9 @@ static int omap_rproc_get_boot_data(struct platform_device *pdev, return -EINVAL; } + of_property_read_u32(np, "ti,bootreg-shift", + &oproc->boot_data->boot_reg_shift); + return 0; }