| Message ID | 20200101145429.16185-1-hdegoede@redhat.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [01/10] Input: goodix - Refactor IRQ pin GPIO accesses | expand |
Hi all, On 1/1/20 3:54 PM, Hans de Goede wrote: > Suspending Goodix touchscreens requires changing the interrupt pin to > output before sending them a power-down command. Followed by wiggling > the interrupt pin to wake the device up, after which it is put back > in input mode. > > So far we have only effectively supported this on devices which use > devicetree. On X86 ACPI platforms both looking up the pins; and using a > pin as both IRQ and GPIO is a bit more complicated. E.g. on some devices > we cannot directly access the IRQ pin as GPIO and we need to call ACPI > methods to control it instead. > > This commit adds a new irq_pin_access_method field to the goodix_chip_data > struct and adds goodix_irq_direction_output and goodix_irq_direction_input > helpers which together abstract the GPIO accesses to the IRQ pin. > > This is a preparation patch for adding support for properly suspending the > touchscreen on X86 ACPI platforms. > > BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317 > BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10 > BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207 > Cc: Dmitry Mastykin <mastichi@gmail.com> > Signed-off-by: Hans de Goede <hdegoede@redhat.com> ping? Can we get this series merged please? Bastien, if you have time it would be good if you can review this series please? Regards, Hans > --- > drivers/input/touchscreen/goodix.c | 62 ++++++++++++++++++++++++------ > 1 file changed, 51 insertions(+), 11 deletions(-) > > diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c > index 0403102e807e..08806a00a9b9 100644 > --- a/drivers/input/touchscreen/goodix.c > +++ b/drivers/input/touchscreen/goodix.c > @@ -31,6 +31,11 @@ > > struct goodix_ts_data; > > +enum goodix_irq_pin_access_method { > + irq_pin_access_none, > + irq_pin_access_gpio, > +}; > + > struct goodix_chip_data { > u16 config_addr; > int config_len; > @@ -53,6 +58,7 @@ struct goodix_ts_data { > const char *cfg_name; > struct completion firmware_loading_complete; > unsigned long irq_flags; > + enum goodix_irq_pin_access_method irq_pin_access_method; > unsigned int contact_size; > }; > > @@ -502,17 +508,48 @@ static int goodix_send_cfg(struct goodix_ts_data *ts, > return 0; > } > > +static int goodix_irq_direction_output(struct goodix_ts_data *ts, > + int value) > +{ > + switch (ts->irq_pin_access_method) { > + case irq_pin_access_none: > + dev_err(&ts->client->dev, > + "%s called without an irq_pin_access_method set\n", > + __func__); > + return -EINVAL; > + case irq_pin_access_gpio: > + return gpiod_direction_output(ts->gpiod_int, value); > + } > + > + return -EINVAL; /* Never reached */ > +} > + > +static int goodix_irq_direction_input(struct goodix_ts_data *ts) > +{ > + switch (ts->irq_pin_access_method) { > + case irq_pin_access_none: > + dev_err(&ts->client->dev, > + "%s called without an irq_pin_access_method set\n", > + __func__); > + return -EINVAL; > + case irq_pin_access_gpio: > + return gpiod_direction_input(ts->gpiod_int); > + } > + > + return -EINVAL; /* Never reached */ > +} > + > static int goodix_int_sync(struct goodix_ts_data *ts) > { > int error; > > - error = gpiod_direction_output(ts->gpiod_int, 0); > + error = goodix_irq_direction_output(ts, 0); > if (error) > return error; > > msleep(50); /* T5: 50ms */ > > - error = gpiod_direction_input(ts->gpiod_int); > + error = goodix_irq_direction_input(ts); > if (error) > return error; > > @@ -536,7 +573,7 @@ static int goodix_reset(struct goodix_ts_data *ts) > msleep(20); /* T2: > 10ms */ > > /* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */ > - error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14); > + error = goodix_irq_direction_output(ts, ts->client->addr == 0x14); > if (error) > return error; > > @@ -617,6 +654,9 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts) > > ts->gpiod_rst = gpiod; > > + if (ts->gpiod_int && ts->gpiod_rst) > + ts->irq_pin_access_method = irq_pin_access_gpio; > + > return 0; > } > > @@ -889,7 +929,7 @@ static int goodix_ts_probe(struct i2c_client *client, > if (error) > return error; > > - if (ts->gpiod_int && ts->gpiod_rst) { > + if (ts->irq_pin_access_method == irq_pin_access_gpio) { > /* reset the controller */ > error = goodix_reset(ts); > if (error) { > @@ -912,7 +952,7 @@ static int goodix_ts_probe(struct i2c_client *client, > > ts->chip = goodix_get_chip_data(ts->id); > > - if (ts->gpiod_int && ts->gpiod_rst) { > + if (ts->irq_pin_access_method == irq_pin_access_gpio) { > /* update device config */ > ts->cfg_name = devm_kasprintf(&client->dev, GFP_KERNEL, > "goodix_%d_cfg.bin", ts->id); > @@ -943,7 +983,7 @@ static int goodix_ts_remove(struct i2c_client *client) > { > struct goodix_ts_data *ts = i2c_get_clientdata(client); > > - if (ts->gpiod_int && ts->gpiod_rst) > + if (ts->irq_pin_access_method == irq_pin_access_gpio) > wait_for_completion(&ts->firmware_loading_complete); > > return 0; > @@ -956,7 +996,7 @@ static int __maybe_unused goodix_suspend(struct device *dev) > int error; > > /* We need gpio pins to suspend/resume */ > - if (!ts->gpiod_int || !ts->gpiod_rst) { > + if (ts->irq_pin_access_method == irq_pin_access_none) { > disable_irq(client->irq); > return 0; > } > @@ -967,7 +1007,7 @@ static int __maybe_unused goodix_suspend(struct device *dev) > goodix_free_irq(ts); > > /* Output LOW on the INT pin for 5 ms */ > - error = gpiod_direction_output(ts->gpiod_int, 0); > + error = goodix_irq_direction_output(ts, 0); > if (error) { > goodix_request_irq(ts); > return error; > @@ -979,7 +1019,7 @@ static int __maybe_unused goodix_suspend(struct device *dev) > GOODIX_CMD_SCREEN_OFF); > if (error) { > dev_err(&ts->client->dev, "Screen off command failed\n"); > - gpiod_direction_input(ts->gpiod_int); > + goodix_irq_direction_input(ts); > goodix_request_irq(ts); > return -EAGAIN; > } > @@ -999,7 +1039,7 @@ static int __maybe_unused goodix_resume(struct device *dev) > struct goodix_ts_data *ts = i2c_get_clientdata(client); > int error; > > - if (!ts->gpiod_int || !ts->gpiod_rst) { > + if (ts->irq_pin_access_method == irq_pin_access_none) { > enable_irq(client->irq); > return 0; > } > @@ -1008,7 +1048,7 @@ static int __maybe_unused goodix_resume(struct device *dev) > * Exit sleep mode by outputting HIGH level to INT pin > * for 2ms~5ms. > */ > - error = gpiod_direction_output(ts->gpiod_int, 1); > + error = goodix_irq_direction_output(ts, 1); > if (error) > return error; > >
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c index 0403102e807e..08806a00a9b9 100644 --- a/drivers/input/touchscreen/goodix.c +++ b/drivers/input/touchscreen/goodix.c @@ -31,6 +31,11 @@ struct goodix_ts_data; +enum goodix_irq_pin_access_method { + irq_pin_access_none, + irq_pin_access_gpio, +}; + struct goodix_chip_data { u16 config_addr; int config_len; @@ -53,6 +58,7 @@ struct goodix_ts_data { const char *cfg_name; struct completion firmware_loading_complete; unsigned long irq_flags; + enum goodix_irq_pin_access_method irq_pin_access_method; unsigned int contact_size; }; @@ -502,17 +508,48 @@ static int goodix_send_cfg(struct goodix_ts_data *ts, return 0; } +static int goodix_irq_direction_output(struct goodix_ts_data *ts, + int value) +{ + switch (ts->irq_pin_access_method) { + case irq_pin_access_none: + dev_err(&ts->client->dev, + "%s called without an irq_pin_access_method set\n", + __func__); + return -EINVAL; + case irq_pin_access_gpio: + return gpiod_direction_output(ts->gpiod_int, value); + } + + return -EINVAL; /* Never reached */ +} + +static int goodix_irq_direction_input(struct goodix_ts_data *ts) +{ + switch (ts->irq_pin_access_method) { + case irq_pin_access_none: + dev_err(&ts->client->dev, + "%s called without an irq_pin_access_method set\n", + __func__); + return -EINVAL; + case irq_pin_access_gpio: + return gpiod_direction_input(ts->gpiod_int); + } + + return -EINVAL; /* Never reached */ +} + static int goodix_int_sync(struct goodix_ts_data *ts) { int error; - error = gpiod_direction_output(ts->gpiod_int, 0); + error = goodix_irq_direction_output(ts, 0); if (error) return error; msleep(50); /* T5: 50ms */ - error = gpiod_direction_input(ts->gpiod_int); + error = goodix_irq_direction_input(ts); if (error) return error; @@ -536,7 +573,7 @@ static int goodix_reset(struct goodix_ts_data *ts) msleep(20); /* T2: > 10ms */ /* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */ - error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14); + error = goodix_irq_direction_output(ts, ts->client->addr == 0x14); if (error) return error; @@ -617,6 +654,9 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts) ts->gpiod_rst = gpiod; + if (ts->gpiod_int && ts->gpiod_rst) + ts->irq_pin_access_method = irq_pin_access_gpio; + return 0; } @@ -889,7 +929,7 @@ static int goodix_ts_probe(struct i2c_client *client, if (error) return error; - if (ts->gpiod_int && ts->gpiod_rst) { + if (ts->irq_pin_access_method == irq_pin_access_gpio) { /* reset the controller */ error = goodix_reset(ts); if (error) { @@ -912,7 +952,7 @@ static int goodix_ts_probe(struct i2c_client *client, ts->chip = goodix_get_chip_data(ts->id); - if (ts->gpiod_int && ts->gpiod_rst) { + if (ts->irq_pin_access_method == irq_pin_access_gpio) { /* update device config */ ts->cfg_name = devm_kasprintf(&client->dev, GFP_KERNEL, "goodix_%d_cfg.bin", ts->id); @@ -943,7 +983,7 @@ static int goodix_ts_remove(struct i2c_client *client) { struct goodix_ts_data *ts = i2c_get_clientdata(client); - if (ts->gpiod_int && ts->gpiod_rst) + if (ts->irq_pin_access_method == irq_pin_access_gpio) wait_for_completion(&ts->firmware_loading_complete); return 0; @@ -956,7 +996,7 @@ static int __maybe_unused goodix_suspend(struct device *dev) int error; /* We need gpio pins to suspend/resume */ - if (!ts->gpiod_int || !ts->gpiod_rst) { + if (ts->irq_pin_access_method == irq_pin_access_none) { disable_irq(client->irq); return 0; } @@ -967,7 +1007,7 @@ static int __maybe_unused goodix_suspend(struct device *dev) goodix_free_irq(ts); /* Output LOW on the INT pin for 5 ms */ - error = gpiod_direction_output(ts->gpiod_int, 0); + error = goodix_irq_direction_output(ts, 0); if (error) { goodix_request_irq(ts); return error; @@ -979,7 +1019,7 @@ static int __maybe_unused goodix_suspend(struct device *dev) GOODIX_CMD_SCREEN_OFF); if (error) { dev_err(&ts->client->dev, "Screen off command failed\n"); - gpiod_direction_input(ts->gpiod_int); + goodix_irq_direction_input(ts); goodix_request_irq(ts); return -EAGAIN; } @@ -999,7 +1039,7 @@ static int __maybe_unused goodix_resume(struct device *dev) struct goodix_ts_data *ts = i2c_get_clientdata(client); int error; - if (!ts->gpiod_int || !ts->gpiod_rst) { + if (ts->irq_pin_access_method == irq_pin_access_none) { enable_irq(client->irq); return 0; } @@ -1008,7 +1048,7 @@ static int __maybe_unused goodix_resume(struct device *dev) * Exit sleep mode by outputting HIGH level to INT pin * for 2ms~5ms. */ - error = gpiod_direction_output(ts->gpiod_int, 1); + error = goodix_irq_direction_output(ts, 1); if (error) return error;
Suspending Goodix touchscreens requires changing the interrupt pin to output before sending them a power-down command. Followed by wiggling the interrupt pin to wake the device up, after which it is put back in input mode. So far we have only effectively supported this on devices which use devicetree. On X86 ACPI platforms both looking up the pins; and using a pin as both IRQ and GPIO is a bit more complicated. E.g. on some devices we cannot directly access the IRQ pin as GPIO and we need to call ACPI methods to control it instead. This commit adds a new irq_pin_access_method field to the goodix_chip_data struct and adds goodix_irq_direction_output and goodix_irq_direction_input helpers which together abstract the GPIO accesses to the IRQ pin. This is a preparation patch for adding support for properly suspending the touchscreen on X86 ACPI platforms. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317 BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10 BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207 Cc: Dmitry Mastykin <mastichi@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- drivers/input/touchscreen/goodix.c | 62 ++++++++++++++++++++++++------ 1 file changed, 51 insertions(+), 11 deletions(-)