[v7,3/5] clk: meson: a1: add support for Amlogic A1 PLL clock driver

Commit Message

Jian Hu Jan. 20, 2020, 3:49 a.m. UTC

The Amlogic A1 clock includes three drivers:
pll clocks, peripheral clocks, CPU clocks.
sys pll and CPU clocks will be sent in next patch.

Unlike the previous series, there is no EE/AO domain
in A1 CLK controllers.

Signed-off-by: Jian Hu <[e-mail]>
---
 drivers/clk/meson/Kconfig  |   9 +
 drivers/clk/meson/Makefile |   1 +
 drivers/clk/meson/a1-pll.c | 360 +++++++++++++++++++++++++++++++++++++
 drivers/clk/meson/a1-pll.h |  56 ++++++
 4 files changed, 426 insertions(+)
 create mode 100644 drivers/clk/meson/a1-pll.c
 create mode 100644 drivers/clk/meson/a1-pll.h

Comments

Jerome Brunet Feb. 4, 2020, 1:13 p.m. UTC | #1

On Mon 20 Jan 2020 at 04:49, Jian Hu <[e-mail]> wrote:

> The Amlogic A1 clock includes three drivers:
> pll clocks, peripheral clocks, CPU clocks.
> sys pll and CPU clocks will be sent in next patch.
>
> Unlike the previous series, there is no EE/AO domain
> in A1 CLK controllers.
>
> Signed-off-by: Jian Hu <[e-mail]>
> ---
>  drivers/clk/meson/Kconfig  |   9 +
>  drivers/clk/meson/Makefile |   1 +
>  drivers/clk/meson/a1-pll.c | 360 +++++++++++++++++++++++++++++++++++++
>  drivers/clk/meson/a1-pll.h |  56 ++++++
>  4 files changed, 426 insertions(+)
>  create mode 100644 drivers/clk/meson/a1-pll.c
>  create mode 100644 drivers/clk/meson/a1-pll.h
>
> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
> index dabeb435d067..31613c3bbbc7 100644
> --- a/drivers/clk/meson/Kconfig
> +++ b/drivers/clk/meson/Kconfig
> @@ -93,6 +93,15 @@ config COMMON_CLK_AXG_AUDIO
>  	  Support for the audio clock controller on AmLogic A113D devices,
>  	  aka axg, Say Y if you want audio subsystem to work.
>  
> +config COMMON_CLK_A1_PLL
> +	bool
> +	depends on ARCH_MESON
> +	select COMMON_CLK_MESON_REGMAP
> +	select COMMON_CLK_MESON_PLL
> +	help
> +	  Support for the PLL clock controller on Amlogic A113L device,
> +	  aka a1. Say Y if you want PLL to work.
> +
>  config COMMON_CLK_G12A
>  	bool
>  	depends on ARCH_MESON
> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
> index 3939f218587a..71d3b8e6fb8a 100644
> --- a/drivers/clk/meson/Makefile
> +++ b/drivers/clk/meson/Makefile
> @@ -16,6 +16,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
>  
>  obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
>  obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
> +obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
>  obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
>  obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
>  obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
> diff --git a/drivers/clk/meson/a1-pll.c b/drivers/clk/meson/a1-pll.c
> new file mode 100644
> index 000000000000..69c1ca07d041
> --- /dev/null
> +++ b/drivers/clk/meson/a1-pll.c
> @@ -0,0 +1,360 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
> + * Author: Jian Hu <[e-mail]>
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include "a1-pll.h"
> +#include "clk-pll.h"
> +#include "clk-regmap.h"
> +
> +static struct clk_regmap a1_fixed_pll_dco = {
> +	.data = &(struct meson_clk_pll_data){
> +		.en = {
> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
> +			.shift   = 28,
> +			.width   = 1,
> +		},
> +		.m = {
> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
> +			.shift   = 0,
> +			.width   = 8,
> +		},
> +		.n = {
> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
> +			.shift   = 10,
> +			.width   = 5,
> +		},
> +		.frac = {
> +			.reg_off = ANACTRL_FIXPLL_CTRL1,
> +			.shift   = 0,
> +			.width   = 19,
> +		},
> +		.l = {
> +			.reg_off = ANACTRL_FIXPLL_STS,
> +			.shift   = 31,
> +			.width   = 1,
> +		},
> +		.rst = {
> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
> +			.shift   = 29,
> +			.width   = 1,
> +		},
> +	},
> +	.hw.init = &(struct clk_init_data){
> +		.name = "fixed_pll_dco",
> +		.ops = &meson_clk_pll_ro_ops,
> +		.parent_data = &(const struct clk_parent_data) {
> +			.fw_name = "xtal_fixpll",
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap a1_fixed_pll = {
> +	.data = &(struct clk_regmap_gate_data){
> +		.offset = ANACTRL_FIXPLL_CTRL0,
> +		.bit_idx = 20,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "fixed_pll",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&a1_fixed_pll_dco.hw
> +		},
> +		.num_parents = 1,
> +		/*
> +		 * It is enough that the fdiv leaf has critical flag,
> +		 * No critical or unused flag here.
> +		 */
> +	},
> +};
> +
> +static const struct pll_mult_range a1_hifi_pll_mult_range = {
> +	.min = 32,
> +	.max = 64,
> +};
> +
> +static const struct reg_sequence a1_hifi_init_regs[] = {
> +	{ .reg = ANACTRL_HIFIPLL_CTRL1, .def = 0x01800000 },
> +	{ .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
> +	{ .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x100a1100 },
> +	{ .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x00302000 },
> +	{ .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x01f18440 },
> +};
> +
> +static struct clk_regmap a1_hifi_pll = {
> +	.data = &(struct meson_clk_pll_data){
> +		.en = {
> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
> +			.shift   = 28,
> +			.width   = 1,
> +		},
> +		.m = {
> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
> +			.shift   = 0,
> +			.width   = 8,
> +		},
> +		.n = {
> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
> +			.shift   = 10,
> +			.width   = 5,
> +		},
> +		.frac = {
> +			.reg_off = ANACTRL_HIFIPLL_CTRL1,
> +			.shift   = 0,
> +			.width   = 19,
> +		},
> +		.l = {
> +			.reg_off = ANACTRL_HIFIPLL_STS,
> +			.shift   = 31,
> +			.width   = 1,
> +		},
> +		.current_en = {
> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
> +			.shift   = 26,
> +			.width   = 1,
> +		},
> +		.l_detect = {
> +			.reg_off = ANACTRL_HIFIPLL_CTRL2,
> +			.shift   = 6,
> +			.width   = 1,
> +		},
> +		.range = &a1_hifi_pll_mult_range,
> +		.init_regs = a1_hifi_init_regs,
> +		.init_count = ARRAY_SIZE(a1_hifi_init_regs),
> +	},
> +	.hw.init = &(struct clk_init_data){
> +		.name = "hifi_pll",
> +		.ops = &meson_clk_pll_ops,
> +		.parent_data = &(const struct clk_parent_data) {
> +			.fw_name = "xtal_hifipll",
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_fixed_factor a1_fclk_div2_div = {
> +	.mult = 1,
> +	.div = 2,
> +	.hw.init = &(struct clk_init_data){
> +		.name = "fclk_div2_div",
> +		.ops = &clk_fixed_factor_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&a1_fixed_pll.hw
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap a1_fclk_div2 = {
> +	.data = &(struct clk_regmap_gate_data){
> +		.offset = ANACTRL_FIXPLL_CTRL0,
> +		.bit_idx = 21,
> +	},
> +	.hw.init = &(struct clk_init_data){
> +		.name = "fclk_div2",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&a1_fclk_div2_div.hw
> +		},
> +		.num_parents = 1,
> +		/*
> +		 * This clock is used by DDR clock in BL2 firmware
> +		 * and is required by the platform to operate correctly.
> +		 * Until the following condition are met, we need this clock to
> +		 * be marked as critical:
> +		 * a) Mark the clock used by a firmware resource, if possible
> +		 * b) CCF has a clock hand-off mechanism to make the sure the
> +		 *    clock stays on until the proper driver comes along
> +		 */
> +		.flags = CLK_IS_CRITICAL,
> +	},
> +};
> +
> +static struct clk_fixed_factor a1_fclk_div3_div = {
> +	.mult = 1,
> +	.div = 3,
> +	.hw.init = &(struct clk_init_data){
> +		.name = "fclk_div3_div",
> +		.ops = &clk_fixed_factor_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&a1_fixed_pll.hw
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap a1_fclk_div3 = {
> +	.data = &(struct clk_regmap_gate_data){
> +		.offset = ANACTRL_FIXPLL_CTRL0,
> +		.bit_idx = 22,
> +	},
> +	.hw.init = &(struct clk_init_data){
> +		.name = "fclk_div3",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&a1_fclk_div3_div.hw
> +		},
> +		.num_parents = 1,
> +		/*
> +		 * This clock is used by APB bus which is set in boot ROM code
> +		 * and is required by the platform to operate correctly.
> +		 * About critical, refer to a1_fclk_div2.
> +		 */
> +		.flags = CLK_IS_CRITICAL,
> +	},
> +};
> +
> +static struct clk_fixed_factor a1_fclk_div5_div = {
> +	.mult = 1,
> +	.div = 5,
> +	.hw.init = &(struct clk_init_data){
> +		.name = "fclk_div5_div",
> +		.ops = &clk_fixed_factor_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&a1_fixed_pll.hw
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap a1_fclk_div5 = {
> +	.data = &(struct clk_regmap_gate_data){
> +		.offset = ANACTRL_FIXPLL_CTRL0,
> +		.bit_idx = 23,
> +	},
> +	.hw.init = &(struct clk_init_data){
> +		.name = "fclk_div5",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&a1_fclk_div5_div.hw
> +		},
> +		.num_parents = 1,
> +		/*
> +		 * This clock is used by AXI bus which setted in Romcode
> +		 * and is required by the platform to operate correctly.
> +		 * About critical, refer to a1_fclk_div2.
> +		 */
> +		.flags = CLK_IS_CRITICAL,
> +	},
> +};
> +
> +static struct clk_fixed_factor a1_fclk_div7_div = {
> +	.mult = 1,
> +	.div = 7,
> +	.hw.init = &(struct clk_init_data){
> +		.name = "fclk_div7_div",
> +		.ops = &clk_fixed_factor_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&a1_fixed_pll.hw
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap a1_fclk_div7 = {
> +	.data = &(struct clk_regmap_gate_data){
> +		.offset = ANACTRL_FIXPLL_CTRL0,
> +		.bit_idx = 24,
> +	},
> +	.hw.init = &(struct clk_init_data){
> +		.name = "fclk_div7",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&a1_fclk_div7_div.hw
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +/* Array of all clocks provided by this provider */
> +static struct clk_hw_onecell_data a1_pll_hw_onecell_data = {
> +	.hws = {
> +		[CLKID_FIXED_PLL_DCO]		= &a1_fixed_pll_dco.hw,
> +		[CLKID_FIXED_PLL]		= &a1_fixed_pll.hw,
> +		[CLKID_HIFI_PLL]		= &a1_hifi_pll.hw,
> +		[CLKID_FCLK_DIV2]		= &a1_fclk_div2.hw,
> +		[CLKID_FCLK_DIV3]		= &a1_fclk_div3.hw,
> +		[CLKID_FCLK_DIV5]		= &a1_fclk_div5.hw,
> +		[CLKID_FCLK_DIV7]		= &a1_fclk_div7.hw,
> +		[CLKID_FCLK_DIV2_DIV]		= &a1_fclk_div2_div.hw,
> +		[CLKID_FCLK_DIV3_DIV]		= &a1_fclk_div3_div.hw,
> +		[CLKID_FCLK_DIV5_DIV]		= &a1_fclk_div5_div.hw,
> +		[CLKID_FCLK_DIV7_DIV]		= &a1_fclk_div7_div.hw,
> +		[NR_PLL_CLKS]			= NULL,
> +	},
> +	.num = NR_PLL_CLKS,
> +};
> +
> +static struct clk_regmap *const a1_pll_regmaps[] = {
> +	&a1_fixed_pll_dco,
> +	&a1_fixed_pll,
> +	&a1_hifi_pll,
> +	&a1_fclk_div2,
> +	&a1_fclk_div3,
> +	&a1_fclk_div5,
> +	&a1_fclk_div7,
> +};
> +
> +static struct regmap_config clkc_regmap_config = {
> +	.reg_bits       = 32,
> +	.val_bits       = 32,
> +	.reg_stride     = 4,
> +};
> +
> +static int meson_a1_pll_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct resource *res;
> +	void __iomem *base;
> +	struct regmap *map;
> +	int ret, i;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +
> +	base = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(base))
> +		return PTR_ERR(base);
> +
> +	map = devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
> +	if (IS_ERR(map))
> +		return PTR_ERR(map);
> +
> +	/* Populate regmap for the regmap backed clocks */
> +	for (i = 0; i < ARRAY_SIZE(a1_pll_regmaps); i++)
> +		a1_pll_regmaps[i]->map = map;
> +
> +	for (i = 0; i < a1_pll_hw_onecell_data.num; i++) {
> +		/* array might be sparse */
> +		if (!a1_pll_hw_onecell_data.hws[i])
> +			continue;
> +
> +		ret = devm_clk_hw_register(dev, a1_pll_hw_onecell_data.hws[i]);
> +		if (ret) {
> +			dev_err(dev, "Clock registration failed\n");
> +			return ret;
> +		}
> +	}
> +
> +	return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
> +					   &a1_pll_hw_onecell_data);
> +}
> +
> +static const struct of_device_id clkc_match_table[] = {
> +	{ .compatible = "amlogic,a1-pll-clkc", },
> +	{}
> +};
> +
> +static struct platform_driver a1_pll_driver = {
> +	.probe		= meson_a1_pll_probe,
> +	.driver		= {
> +		.name	= "a1-pll-clkc",
> +		.of_match_table = clkc_match_table,
> +	},
> +};
> +
> +builtin_platform_driver(a1_pll_driver);
> diff --git a/drivers/clk/meson/a1-pll.h b/drivers/clk/meson/a1-pll.h
> new file mode 100644
> index 000000000000..8ded267061ad
> --- /dev/null
> +++ b/drivers/clk/meson/a1-pll.h
> @@ -0,0 +1,56 @@
> +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
> +/*
> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
> + */
> +
> +#ifndef __A1_PLL_H
> +#define __A1_PLL_H
> +
> +/* PLL register offset */
> +#define ANACTRL_FIXPLL_CTRL0		0x0
> +#define ANACTRL_FIXPLL_CTRL1		0x4
> +#define ANACTRL_FIXPLL_CTRL2		0x8
> +#define ANACTRL_FIXPLL_CTRL3		0xc
> +#define ANACTRL_FIXPLL_CTRL4		0x10
> +#define ANACTRL_FIXPLL_STS		0x14
> +#define ANACTRL_SYSPLL_CTRL0		0x80
> +#define ANACTRL_SYSPLL_CTRL1		0x84
> +#define ANACTRL_SYSPLL_CTRL2		0x88
> +#define ANACTRL_SYSPLL_CTRL3		0x8c
> +#define ANACTRL_SYSPLL_CTRL4		0x90
> +#define ANACTRL_SYSPLL_STS		0x94
> +#define ANACTRL_HIFIPLL_CTRL0		0xc0
> +#define ANACTRL_HIFIPLL_CTRL1		0xc4
> +#define ANACTRL_HIFIPLL_CTRL2		0xc8
> +#define ANACTRL_HIFIPLL_CTRL3		0xcc
> +#define ANACTRL_HIFIPLL_CTRL4		0xd0
> +#define ANACTRL_HIFIPLL_STS		0xd4

Non of the definition below are used.
What are they ? Do you need them ?

> +#define ANACTRL_AUDDDS_CTRL0		0x100
> +#define ANACTRL_AUDDDS_CTRL1		0x104
> +#define ANACTRL_AUDDDS_CTRL2		0x108
> +#define ANACTRL_AUDDDS_CTRL3		0x10c
> +#define ANACTRL_AUDDDS_CTRL4		0x110
> +#define ANACTRL_AUDDDS_STS		0x114
> +#define ANACTRL_MISCTOP_CTRL0		0x140
> +#define ANACTRL_POR_CNTL		0x188
> +
> +/*
> + * CLKID index values
> + *
> + * These indices are entirely contrived and do not map onto the hardware.
> + * It has now been decided to expose everything by default in the DT header:
> + * include/dt-bindings/clock/a1-pll-clkc.h. Only the clocks ids we don't want
> + * to expose, such as the internal muxes and dividers of composite clocks,
> + * will remain defined here.
> + */
> +#define CLKID_FIXED_PLL_DCO		0
> +#define CLKID_FCLK_DIV2_DIV		2
> +#define CLKID_FCLK_DIV3_DIV		3
> +#define CLKID_FCLK_DIV5_DIV		4
> +#define CLKID_FCLK_DIV7_DIV		5
> +#define NR_PLL_CLKS			11
> +
> +/* include the CLKIDs that have been made part of the DT binding */
> +#include <dt-bindings/clock/a1-pll-clkc.h>
> +
> +#endif /* __A1_PLL_H */

Jian Hu Feb. 10, 2020, 6:16 a.m. UTC | #2

On 2020/2/4 21:13, Jerome Brunet wrote:
> 
> On Mon 20 Jan 2020 at 04:49, Jian Hu <[e-mail]> wrote:
> 
>> The Amlogic A1 clock includes three drivers:
>> pll clocks, peripheral clocks, CPU clocks.
>> sys pll and CPU clocks will be sent in next patch.
>>
>> Unlike the previous series, there is no EE/AO domain
>> in A1 CLK controllers.
>>
>> Signed-off-by: Jian Hu <[e-mail]>
>> ---
>>   drivers/clk/meson/Kconfig  |   9 +
>>   drivers/clk/meson/Makefile |   1 +
>>   drivers/clk/meson/a1-pll.c | 360 +++++++++++++++++++++++++++++++++++++
>>   drivers/clk/meson/a1-pll.h |  56 ++++++
>>   4 files changed, 426 insertions(+)
>>   create mode 100644 drivers/clk/meson/a1-pll.c
>>   create mode 100644 drivers/clk/meson/a1-pll.h
>>
>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>> index dabeb435d067..31613c3bbbc7 100644
>> --- a/drivers/clk/meson/Kconfig
>> +++ b/drivers/clk/meson/Kconfig
>> @@ -93,6 +93,15 @@ config COMMON_CLK_AXG_AUDIO
>>   	  Support for the audio clock controller on AmLogic A113D devices,
>>   	  aka axg, Say Y if you want audio subsystem to work.
>>   
>> +config COMMON_CLK_A1_PLL
>> +	bool
>> +	depends on ARCH_MESON
>> +	select COMMON_CLK_MESON_REGMAP
>> +	select COMMON_CLK_MESON_PLL
>> +	help
>> +	  Support for the PLL clock controller on Amlogic A113L device,
>> +	  aka a1. Say Y if you want PLL to work.
>> +
>>   config COMMON_CLK_G12A
>>   	bool
>>   	depends on ARCH_MESON
>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>> index 3939f218587a..71d3b8e6fb8a 100644
>> --- a/drivers/clk/meson/Makefile
>> +++ b/drivers/clk/meson/Makefile
>> @@ -16,6 +16,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
>>   
>>   obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
>>   obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>> +obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
>>   obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
>>   obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
>>   obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
>> diff --git a/drivers/clk/meson/a1-pll.c b/drivers/clk/meson/a1-pll.c
>> new file mode 100644
>> index 000000000000..69c1ca07d041
>> --- /dev/null
>> +++ b/drivers/clk/meson/a1-pll.c
>> @@ -0,0 +1,360 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>> + * Author: Jian Hu <[e-mail]>
>> + */
>> +
>> +#include <linux/clk-provider.h>
>> +#include <linux/of_device.h>
>> +#include <linux/platform_device.h>
>> +#include "a1-pll.h"
>> +#include "clk-pll.h"
>> +#include "clk-regmap.h"
>> +
>> +static struct clk_regmap a1_fixed_pll_dco = {
>> +	.data = &(struct meson_clk_pll_data){
>> +		.en = {
>> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
>> +			.shift   = 28,
>> +			.width   = 1,
>> +		},
>> +		.m = {
>> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
>> +			.shift   = 0,
>> +			.width   = 8,
>> +		},
>> +		.n = {
>> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
>> +			.shift   = 10,
>> +			.width   = 5,
>> +		},
>> +		.frac = {
>> +			.reg_off = ANACTRL_FIXPLL_CTRL1,
>> +			.shift   = 0,
>> +			.width   = 19,
>> +		},
>> +		.l = {
>> +			.reg_off = ANACTRL_FIXPLL_STS,
>> +			.shift   = 31,
>> +			.width   = 1,
>> +		},
>> +		.rst = {
>> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
>> +			.shift   = 29,
>> +			.width   = 1,
>> +		},
>> +	},
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "fixed_pll_dco",
>> +		.ops = &meson_clk_pll_ro_ops,
>> +		.parent_data = &(const struct clk_parent_data) {
>> +			.fw_name = "xtal_fixpll",
>> +		},
>> +		.num_parents = 1,
>> +	},
>> +};
>> +
>> +static struct clk_regmap a1_fixed_pll = {
>> +	.data = &(struct clk_regmap_gate_data){
>> +		.offset = ANACTRL_FIXPLL_CTRL0,
>> +		.bit_idx = 20,
>> +	},
>> +	.hw.init = &(struct clk_init_data) {
>> +		.name = "fixed_pll",
>> +		.ops = &clk_regmap_gate_ops,
>> +		.parent_hws = (const struct clk_hw *[]) {
>> +			&a1_fixed_pll_dco.hw
>> +		},
>> +		.num_parents = 1,
>> +		/*
>> +		 * It is enough that the fdiv leaf has critical flag,
>> +		 * No critical or unused flag here.
>> +		 */
>> +	},
>> +};
>> +
>> +static const struct pll_mult_range a1_hifi_pll_mult_range = {
>> +	.min = 32,
>> +	.max = 64,
>> +};
>> +
>> +static const struct reg_sequence a1_hifi_init_regs[] = {
>> +	{ .reg = ANACTRL_HIFIPLL_CTRL1, .def = 0x01800000 },
>> +	{ .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
>> +	{ .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x100a1100 },
>> +	{ .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x00302000 },
>> +	{ .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x01f18440 },
>> +};
>> +
>> +static struct clk_regmap a1_hifi_pll = {
>> +	.data = &(struct meson_clk_pll_data){
>> +		.en = {
>> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
>> +			.shift   = 28,
>> +			.width   = 1,
>> +		},
>> +		.m = {
>> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
>> +			.shift   = 0,
>> +			.width   = 8,
>> +		},
>> +		.n = {
>> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
>> +			.shift   = 10,
>> +			.width   = 5,
>> +		},
>> +		.frac = {
>> +			.reg_off = ANACTRL_HIFIPLL_CTRL1,
>> +			.shift   = 0,
>> +			.width   = 19,
>> +		},
>> +		.l = {
>> +			.reg_off = ANACTRL_HIFIPLL_STS,
>> +			.shift   = 31,
>> +			.width   = 1,
>> +		},
>> +		.current_en = {
>> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
>> +			.shift   = 26,
>> +			.width   = 1,
>> +		},
>> +		.l_detect = {
>> +			.reg_off = ANACTRL_HIFIPLL_CTRL2,
>> +			.shift   = 6,
>> +			.width   = 1,
>> +		},
>> +		.range = &a1_hifi_pll_mult_range,
>> +		.init_regs = a1_hifi_init_regs,
>> +		.init_count = ARRAY_SIZE(a1_hifi_init_regs),
>> +	},
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "hifi_pll",
>> +		.ops = &meson_clk_pll_ops,
>> +		.parent_data = &(const struct clk_parent_data) {
>> +			.fw_name = "xtal_hifipll",
>> +		},
>> +		.num_parents = 1,
>> +	},
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div2_div = {
>> +	.mult = 1,
>> +	.div = 2,
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "fclk_div2_div",
>> +		.ops = &clk_fixed_factor_ops,
>> +		.parent_hws = (const struct clk_hw *[]) {
>> +			&a1_fixed_pll.hw
>> +		},
>> +		.num_parents = 1,
>> +	},
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div2 = {
>> +	.data = &(struct clk_regmap_gate_data){
>> +		.offset = ANACTRL_FIXPLL_CTRL0,
>> +		.bit_idx = 21,
>> +	},
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "fclk_div2",
>> +		.ops = &clk_regmap_gate_ops,
>> +		.parent_hws = (const struct clk_hw *[]) {
>> +			&a1_fclk_div2_div.hw
>> +		},
>> +		.num_parents = 1,
>> +		/*
>> +		 * This clock is used by DDR clock in BL2 firmware
>> +		 * and is required by the platform to operate correctly.
>> +		 * Until the following condition are met, we need this clock to
>> +		 * be marked as critical:
>> +		 * a) Mark the clock used by a firmware resource, if possible
>> +		 * b) CCF has a clock hand-off mechanism to make the sure the
>> +		 *    clock stays on until the proper driver comes along
>> +		 */
>> +		.flags = CLK_IS_CRITICAL,
>> +	},
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div3_div = {
>> +	.mult = 1,
>> +	.div = 3,
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "fclk_div3_div",
>> +		.ops = &clk_fixed_factor_ops,
>> +		.parent_hws = (const struct clk_hw *[]) {
>> +			&a1_fixed_pll.hw
>> +		},
>> +		.num_parents = 1,
>> +	},
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div3 = {
>> +	.data = &(struct clk_regmap_gate_data){
>> +		.offset = ANACTRL_FIXPLL_CTRL0,
>> +		.bit_idx = 22,
>> +	},
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "fclk_div3",
>> +		.ops = &clk_regmap_gate_ops,
>> +		.parent_hws = (const struct clk_hw *[]) {
>> +			&a1_fclk_div3_div.hw
>> +		},
>> +		.num_parents = 1,
>> +		/*
>> +		 * This clock is used by APB bus which is set in boot ROM code
>> +		 * and is required by the platform to operate correctly.
>> +		 * About critical, refer to a1_fclk_div2.
>> +		 */
>> +		.flags = CLK_IS_CRITICAL,
>> +	},
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div5_div = {
>> +	.mult = 1,
>> +	.div = 5,
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "fclk_div5_div",
>> +		.ops = &clk_fixed_factor_ops,
>> +		.parent_hws = (const struct clk_hw *[]) {
>> +			&a1_fixed_pll.hw
>> +		},
>> +		.num_parents = 1,
>> +	},
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div5 = {
>> +	.data = &(struct clk_regmap_gate_data){
>> +		.offset = ANACTRL_FIXPLL_CTRL0,
>> +		.bit_idx = 23,
>> +	},
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "fclk_div5",
>> +		.ops = &clk_regmap_gate_ops,
>> +		.parent_hws = (const struct clk_hw *[]) {
>> +			&a1_fclk_div5_div.hw
>> +		},
>> +		.num_parents = 1,
>> +		/*
>> +		 * This clock is used by AXI bus which setted in Romcode
>> +		 * and is required by the platform to operate correctly.
>> +		 * About critical, refer to a1_fclk_div2.
>> +		 */
>> +		.flags = CLK_IS_CRITICAL,
>> +	},
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div7_div = {
>> +	.mult = 1,
>> +	.div = 7,
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "fclk_div7_div",
>> +		.ops = &clk_fixed_factor_ops,
>> +		.parent_hws = (const struct clk_hw *[]) {
>> +			&a1_fixed_pll.hw
>> +		},
>> +		.num_parents = 1,
>> +	},
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div7 = {
>> +	.data = &(struct clk_regmap_gate_data){
>> +		.offset = ANACTRL_FIXPLL_CTRL0,
>> +		.bit_idx = 24,
>> +	},
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "fclk_div7",
>> +		.ops = &clk_regmap_gate_ops,
>> +		.parent_hws = (const struct clk_hw *[]) {
>> +			&a1_fclk_div7_div.hw
>> +		},
>> +		.num_parents = 1,
>> +	},
>> +};
>> +
>> +/* Array of all clocks provided by this provider */
>> +static struct clk_hw_onecell_data a1_pll_hw_onecell_data = {
>> +	.hws = {
>> +		[CLKID_FIXED_PLL_DCO]		= &a1_fixed_pll_dco.hw,
>> +		[CLKID_FIXED_PLL]		= &a1_fixed_pll.hw,
>> +		[CLKID_HIFI_PLL]		= &a1_hifi_pll.hw,
>> +		[CLKID_FCLK_DIV2]		= &a1_fclk_div2.hw,
>> +		[CLKID_FCLK_DIV3]		= &a1_fclk_div3.hw,
>> +		[CLKID_FCLK_DIV5]		= &a1_fclk_div5.hw,
>> +		[CLKID_FCLK_DIV7]		= &a1_fclk_div7.hw,
>> +		[CLKID_FCLK_DIV2_DIV]		= &a1_fclk_div2_div.hw,
>> +		[CLKID_FCLK_DIV3_DIV]		= &a1_fclk_div3_div.hw,
>> +		[CLKID_FCLK_DIV5_DIV]		= &a1_fclk_div5_div.hw,
>> +		[CLKID_FCLK_DIV7_DIV]		= &a1_fclk_div7_div.hw,
>> +		[NR_PLL_CLKS]			= NULL,
>> +	},
>> +	.num = NR_PLL_CLKS,
>> +};
>> +
>> +static struct clk_regmap *const a1_pll_regmaps[] = {
>> +	&a1_fixed_pll_dco,
>> +	&a1_fixed_pll,
>> +	&a1_hifi_pll,
>> +	&a1_fclk_div2,
>> +	&a1_fclk_div3,
>> +	&a1_fclk_div5,
>> +	&a1_fclk_div7,
>> +};
>> +
>> +static struct regmap_config clkc_regmap_config = {
>> +	.reg_bits       = 32,
>> +	.val_bits       = 32,
>> +	.reg_stride     = 4,
>> +};
>> +
>> +static int meson_a1_pll_probe(struct platform_device *pdev)
>> +{
>> +	struct device *dev = &pdev->dev;
>> +	struct resource *res;
>> +	void __iomem *base;
>> +	struct regmap *map;
>> +	int ret, i;
>> +
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +
>> +	base = devm_ioremap_resource(dev, res);
>> +	if (IS_ERR(base))
>> +		return PTR_ERR(base);
>> +
>> +	map = devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
>> +	if (IS_ERR(map))
>> +		return PTR_ERR(map);
>> +
>> +	/* Populate regmap for the regmap backed clocks */
>> +	for (i = 0; i < ARRAY_SIZE(a1_pll_regmaps); i++)
>> +		a1_pll_regmaps[i]->map = map;
>> +
>> +	for (i = 0; i < a1_pll_hw_onecell_data.num; i++) {
>> +		/* array might be sparse */
>> +		if (!a1_pll_hw_onecell_data.hws[i])
>> +			continue;
>> +
>> +		ret = devm_clk_hw_register(dev, a1_pll_hw_onecell_data.hws[i]);
>> +		if (ret) {
>> +			dev_err(dev, "Clock registration failed\n");
>> +			return ret;
>> +		}
>> +	}
>> +
>> +	return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
>> +					   &a1_pll_hw_onecell_data);
>> +}
>> +
>> +static const struct of_device_id clkc_match_table[] = {
>> +	{ .compatible = "amlogic,a1-pll-clkc", },
>> +	{}
>> +};
>> +
>> +static struct platform_driver a1_pll_driver = {
>> +	.probe		= meson_a1_pll_probe,
>> +	.driver		= {
>> +		.name	= "a1-pll-clkc",
>> +		.of_match_table = clkc_match_table,
>> +	},
>> +};
>> +
>> +builtin_platform_driver(a1_pll_driver);
>> diff --git a/drivers/clk/meson/a1-pll.h b/drivers/clk/meson/a1-pll.h
>> new file mode 100644
>> index 000000000000..8ded267061ad
>> --- /dev/null
>> +++ b/drivers/clk/meson/a1-pll.h
>> @@ -0,0 +1,56 @@
>> +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
>> +/*
>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>> + */
>> +
>> +#ifndef __A1_PLL_H
>> +#define __A1_PLL_H
>> +
>> +/* PLL register offset */
>> +#define ANACTRL_FIXPLL_CTRL0		0x0
>> +#define ANACTRL_FIXPLL_CTRL1		0x4
>> +#define ANACTRL_FIXPLL_CTRL2		0x8
>> +#define ANACTRL_FIXPLL_CTRL3		0xc
>> +#define ANACTRL_FIXPLL_CTRL4		0x10
>> +#define ANACTRL_FIXPLL_STS		0x14
>> +#define ANACTRL_SYSPLL_CTRL0		0x80
>> +#define ANACTRL_SYSPLL_CTRL1		0x84
>> +#define ANACTRL_SYSPLL_CTRL2		0x88
>> +#define ANACTRL_SYSPLL_CTRL3		0x8c
>> +#define ANACTRL_SYSPLL_CTRL4		0x90
>> +#define ANACTRL_SYSPLL_STS		0x94
>> +#define ANACTRL_HIFIPLL_CTRL0		0xc0
>> +#define ANACTRL_HIFIPLL_CTRL1		0xc4
>> +#define ANACTRL_HIFIPLL_CTRL2		0xc8
>> +#define ANACTRL_HIFIPLL_CTRL3		0xcc
>> +#define ANACTRL_HIFIPLL_CTRL4		0xd0
>> +#define ANACTRL_HIFIPLL_STS		0xd4
> 
> Non of the definition below are used.
> What are they ? Do you need them ?
> 
They have not been used, It is a PLL used by audio.
I will remove them.
>> +#define ANACTRL_AUDDDS_CTRL0		0x100
>> +#define ANACTRL_AUDDDS_CTRL1		0x104
>> +#define ANACTRL_AUDDDS_CTRL2		0x108
>> +#define ANACTRL_AUDDDS_CTRL3		0x10c
>> +#define ANACTRL_AUDDDS_CTRL4		0x110
>> +#define ANACTRL_AUDDDS_STS		0x114
>> +#define ANACTRL_MISCTOP_CTRL0		0x140
>> +#define ANACTRL_POR_CNTL		0x188
>> +
>> +/*
>> + * CLKID index values
>> + *
>> + * These indices are entirely contrived and do not map onto the hardware.
>> + * It has now been decided to expose everything by default in the DT header:
>> + * include/dt-bindings/clock/a1-pll-clkc.h. Only the clocks ids we don't want
>> + * to expose, such as the internal muxes and dividers of composite clocks,
>> + * will remain defined here.
>> + */
>> +#define CLKID_FIXED_PLL_DCO		0
>> +#define CLKID_FCLK_DIV2_DIV		2
>> +#define CLKID_FCLK_DIV3_DIV		3
>> +#define CLKID_FCLK_DIV5_DIV		4
>> +#define CLKID_FCLK_DIV7_DIV		5
>> +#define NR_PLL_CLKS			11
>> +
>> +/* include the CLKIDs that have been made part of the DT binding */
>> +#include <dt-bindings/clock/a1-pll-clkc.h>
>> +
>> +#endif /* __A1_PLL_H */
> 
> .
>

Patch

diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
index dabeb435d067..31613c3bbbc7 100644
--- a/drivers/clk/meson/Kconfig
+++ b/drivers/clk/meson/Kconfig
@@ -93,6 +93,15 @@  config COMMON_CLK_AXG_AUDIO
 	  Support for the audio clock controller on AmLogic A113D devices,
 	  aka axg, Say Y if you want audio subsystem to work.
 
+config COMMON_CLK_A1_PLL
+	bool
+	depends on ARCH_MESON
+	select COMMON_CLK_MESON_REGMAP
+	select COMMON_CLK_MESON_PLL
+	help
+	  Support for the PLL clock controller on Amlogic A113L device,
+	  aka a1. Say Y if you want PLL to work.
+
 config COMMON_CLK_G12A
 	bool
 	depends on ARCH_MESON
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index 3939f218587a..71d3b8e6fb8a 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -16,6 +16,7 @@  obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
 
 obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
 obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
+obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
 obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
 obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
 obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
diff --git a/drivers/clk/meson/a1-pll.c b/drivers/clk/meson/a1-pll.c
new file mode 100644
index 000000000000..69c1ca07d041
--- /dev/null
+++ b/drivers/clk/meson/a1-pll.c
@@ -0,0 +1,360 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ * Author: Jian Hu <[e-mail]>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "a1-pll.h"
+#include "clk-pll.h"
+#include "clk-regmap.h"
+
+static struct clk_regmap a1_fixed_pll_dco = {
+	.data = &(struct meson_clk_pll_data){
+		.en = {
+			.reg_off = ANACTRL_FIXPLL_CTRL0,
+			.shift   = 28,
+			.width   = 1,
+		},
+		.m = {
+			.reg_off = ANACTRL_FIXPLL_CTRL0,
+			.shift   = 0,
+			.width   = 8,
+		},
+		.n = {
+			.reg_off = ANACTRL_FIXPLL_CTRL0,
+			.shift   = 10,
+			.width   = 5,
+		},
+		.frac = {
+			.reg_off = ANACTRL_FIXPLL_CTRL1,
+			.shift   = 0,
+			.width   = 19,
+		},
+		.l = {
+			.reg_off = ANACTRL_FIXPLL_STS,
+			.shift   = 31,
+			.width   = 1,
+		},
+		.rst = {
+			.reg_off = ANACTRL_FIXPLL_CTRL0,
+			.shift   = 29,
+			.width   = 1,
+		},
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "fixed_pll_dco",
+		.ops = &meson_clk_pll_ro_ops,
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "xtal_fixpll",
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap a1_fixed_pll = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = ANACTRL_FIXPLL_CTRL0,
+		.bit_idx = 20,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "fixed_pll",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fixed_pll_dco.hw
+		},
+		.num_parents = 1,
+		/*
+		 * It is enough that the fdiv leaf has critical flag,
+		 * No critical or unused flag here.
+		 */
+	},
+};
+
+static const struct pll_mult_range a1_hifi_pll_mult_range = {
+	.min = 32,
+	.max = 64,
+};
+
+static const struct reg_sequence a1_hifi_init_regs[] = {
+	{ .reg = ANACTRL_HIFIPLL_CTRL1, .def = 0x01800000 },
+	{ .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
+	{ .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x100a1100 },
+	{ .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x00302000 },
+	{ .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x01f18440 },
+};
+
+static struct clk_regmap a1_hifi_pll = {
+	.data = &(struct meson_clk_pll_data){
+		.en = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL0,
+			.shift   = 28,
+			.width   = 1,
+		},
+		.m = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL0,
+			.shift   = 0,
+			.width   = 8,
+		},
+		.n = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL0,
+			.shift   = 10,
+			.width   = 5,
+		},
+		.frac = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL1,
+			.shift   = 0,
+			.width   = 19,
+		},
+		.l = {
+			.reg_off = ANACTRL_HIFIPLL_STS,
+			.shift   = 31,
+			.width   = 1,
+		},
+		.current_en = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL0,
+			.shift   = 26,
+			.width   = 1,
+		},
+		.l_detect = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL2,
+			.shift   = 6,
+			.width   = 1,
+		},
+		.range = &a1_hifi_pll_mult_range,
+		.init_regs = a1_hifi_init_regs,
+		.init_count = ARRAY_SIZE(a1_hifi_init_regs),
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "hifi_pll",
+		.ops = &meson_clk_pll_ops,
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "xtal_hifipll",
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_fixed_factor a1_fclk_div2_div = {
+	.mult = 1,
+	.div = 2,
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div2_div",
+		.ops = &clk_fixed_factor_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fixed_pll.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap a1_fclk_div2 = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = ANACTRL_FIXPLL_CTRL0,
+		.bit_idx = 21,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div2",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fclk_div2_div.hw
+		},
+		.num_parents = 1,
+		/*
+		 * This clock is used by DDR clock in BL2 firmware
+		 * and is required by the platform to operate correctly.
+		 * Until the following condition are met, we need this clock to
+		 * be marked as critical:
+		 * a) Mark the clock used by a firmware resource, if possible
+		 * b) CCF has a clock hand-off mechanism to make the sure the
+		 *    clock stays on until the proper driver comes along
+		 */
+		.flags = CLK_IS_CRITICAL,
+	},
+};
+
+static struct clk_fixed_factor a1_fclk_div3_div = {
+	.mult = 1,
+	.div = 3,
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div3_div",
+		.ops = &clk_fixed_factor_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fixed_pll.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap a1_fclk_div3 = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = ANACTRL_FIXPLL_CTRL0,
+		.bit_idx = 22,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div3",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fclk_div3_div.hw
+		},
+		.num_parents = 1,
+		/*
+		 * This clock is used by APB bus which is set in boot ROM code
+		 * and is required by the platform to operate correctly.
+		 * About critical, refer to a1_fclk_div2.
+		 */
+		.flags = CLK_IS_CRITICAL,
+	},
+};
+
+static struct clk_fixed_factor a1_fclk_div5_div = {
+	.mult = 1,
+	.div = 5,
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div5_div",
+		.ops = &clk_fixed_factor_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fixed_pll.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap a1_fclk_div5 = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = ANACTRL_FIXPLL_CTRL0,
+		.bit_idx = 23,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div5",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fclk_div5_div.hw
+		},
+		.num_parents = 1,
+		/*
+		 * This clock is used by AXI bus which setted in Romcode
+		 * and is required by the platform to operate correctly.
+		 * About critical, refer to a1_fclk_div2.
+		 */
+		.flags = CLK_IS_CRITICAL,
+	},
+};
+
+static struct clk_fixed_factor a1_fclk_div7_div = {
+	.mult = 1,
+	.div = 7,
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div7_div",
+		.ops = &clk_fixed_factor_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fixed_pll.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap a1_fclk_div7 = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = ANACTRL_FIXPLL_CTRL0,
+		.bit_idx = 24,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div7",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fclk_div7_div.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+/* Array of all clocks provided by this provider */
+static struct clk_hw_onecell_data a1_pll_hw_onecell_data = {
+	.hws = {
+		[CLKID_FIXED_PLL_DCO]		= &a1_fixed_pll_dco.hw,
+		[CLKID_FIXED_PLL]		= &a1_fixed_pll.hw,
+		[CLKID_HIFI_PLL]		= &a1_hifi_pll.hw,
+		[CLKID_FCLK_DIV2]		= &a1_fclk_div2.hw,
+		[CLKID_FCLK_DIV3]		= &a1_fclk_div3.hw,
+		[CLKID_FCLK_DIV5]		= &a1_fclk_div5.hw,
+		[CLKID_FCLK_DIV7]		= &a1_fclk_div7.hw,
+		[CLKID_FCLK_DIV2_DIV]		= &a1_fclk_div2_div.hw,
+		[CLKID_FCLK_DIV3_DIV]		= &a1_fclk_div3_div.hw,
+		[CLKID_FCLK_DIV5_DIV]		= &a1_fclk_div5_div.hw,
+		[CLKID_FCLK_DIV7_DIV]		= &a1_fclk_div7_div.hw,
+		[NR_PLL_CLKS]			= NULL,
+	},
+	.num = NR_PLL_CLKS,
+};
+
+static struct clk_regmap *const a1_pll_regmaps[] = {
+	&a1_fixed_pll_dco,
+	&a1_fixed_pll,
+	&a1_hifi_pll,
+	&a1_fclk_div2,
+	&a1_fclk_div3,
+	&a1_fclk_div5,
+	&a1_fclk_div7,
+};
+
+static struct regmap_config clkc_regmap_config = {
+	.reg_bits       = 32,
+	.val_bits       = 32,
+	.reg_stride     = 4,
+};
+
+static int meson_a1_pll_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	void __iomem *base;
+	struct regmap *map;
+	int ret, i;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+	base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	map = devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
+	if (IS_ERR(map))
+		return PTR_ERR(map);
+
+	/* Populate regmap for the regmap backed clocks */
+	for (i = 0; i < ARRAY_SIZE(a1_pll_regmaps); i++)
+		a1_pll_regmaps[i]->map = map;
+
+	for (i = 0; i < a1_pll_hw_onecell_data.num; i++) {
+		/* array might be sparse */
+		if (!a1_pll_hw_onecell_data.hws[i])
+			continue;
+
+		ret = devm_clk_hw_register(dev, a1_pll_hw_onecell_data.hws[i]);
+		if (ret) {
+			dev_err(dev, "Clock registration failed\n");
+			return ret;
+		}
+	}
+
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
+					   &a1_pll_hw_onecell_data);
+}
+
+static const struct of_device_id clkc_match_table[] = {
+	{ .compatible = "amlogic,a1-pll-clkc", },
+	{}
+};
+
+static struct platform_driver a1_pll_driver = {
+	.probe		= meson_a1_pll_probe,
+	.driver		= {
+		.name	= "a1-pll-clkc",
+		.of_match_table = clkc_match_table,
+	},
+};
+
+builtin_platform_driver(a1_pll_driver);
diff --git a/drivers/clk/meson/a1-pll.h b/drivers/clk/meson/a1-pll.h
new file mode 100644
index 000000000000..8ded267061ad
--- /dev/null
+++ b/drivers/clk/meson/a1-pll.h
@@ -0,0 +1,56 @@ 
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ */
+
+#ifndef __A1_PLL_H
+#define __A1_PLL_H
+
+/* PLL register offset */
+#define ANACTRL_FIXPLL_CTRL0		0x0
+#define ANACTRL_FIXPLL_CTRL1		0x4
+#define ANACTRL_FIXPLL_CTRL2		0x8
+#define ANACTRL_FIXPLL_CTRL3		0xc
+#define ANACTRL_FIXPLL_CTRL4		0x10
+#define ANACTRL_FIXPLL_STS		0x14
+#define ANACTRL_SYSPLL_CTRL0		0x80
+#define ANACTRL_SYSPLL_CTRL1		0x84
+#define ANACTRL_SYSPLL_CTRL2		0x88
+#define ANACTRL_SYSPLL_CTRL3		0x8c
+#define ANACTRL_SYSPLL_CTRL4		0x90
+#define ANACTRL_SYSPLL_STS		0x94
+#define ANACTRL_HIFIPLL_CTRL0		0xc0
+#define ANACTRL_HIFIPLL_CTRL1		0xc4
+#define ANACTRL_HIFIPLL_CTRL2		0xc8
+#define ANACTRL_HIFIPLL_CTRL3		0xcc
+#define ANACTRL_HIFIPLL_CTRL4		0xd0
+#define ANACTRL_HIFIPLL_STS		0xd4
+#define ANACTRL_AUDDDS_CTRL0		0x100
+#define ANACTRL_AUDDDS_CTRL1		0x104
+#define ANACTRL_AUDDDS_CTRL2		0x108
+#define ANACTRL_AUDDDS_CTRL3		0x10c
+#define ANACTRL_AUDDDS_CTRL4		0x110
+#define ANACTRL_AUDDDS_STS		0x114
+#define ANACTRL_MISCTOP_CTRL0		0x140
+#define ANACTRL_POR_CNTL		0x188
+
+/*
+ * CLKID index values
+ *
+ * These indices are entirely contrived and do not map onto the hardware.
+ * It has now been decided to expose everything by default in the DT header:
+ * include/dt-bindings/clock/a1-pll-clkc.h. Only the clocks ids we don't want
+ * to expose, such as the internal muxes and dividers of composite clocks,
+ * will remain defined here.
+ */
+#define CLKID_FIXED_PLL_DCO		0
+#define CLKID_FCLK_DIV2_DIV		2
+#define CLKID_FCLK_DIV3_DIV		3
+#define CLKID_FCLK_DIV5_DIV		4
+#define CLKID_FCLK_DIV7_DIV		5
+#define NR_PLL_CLKS			11
+
+/* include the CLKIDs that have been made part of the DT binding */
+#include <dt-bindings/clock/a1-pll-clkc.h>
+
+#endif /* __A1_PLL_H */