| Message ID | 20200421124057.19238-4-o.rempel@pengutronix.de (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | mainline Protonic boards | expand |
Hi Oleksij, On 20-04-21 14:40, Oleksij Rempel wrote: > The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch > touchscreen display. > > Reviewed-by: Rob Herring <robh@kernel.org> > Signed-off-by: Robin van der Gracht <robin@protonic.nl> > Signed-off-by: David Jander <david@protonic.nl> > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6dl-prtvt7.dts | 472 ++++++++++++++++++++++++++++ > 2 files changed, 473 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 8ce744f1cbfc9..66ee89e7929f9 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > imx6dl-pico-hobbit.dtb \ > imx6dl-pico-nymph.dtb \ > imx6dl-pico-pi.dtb \ > + imx6dl-prtvt7.dtb \ > imx6dl-rex-basic.dtb \ > imx6dl-riotboard.dtb \ > imx6dl-sabreauto.dtb \ > diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts > new file mode 100644 > index 0000000000000..a948c7c6eb3ce > --- /dev/null > +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts > @@ -0,0 +1,472 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > +/* > + * Copyright (c) 2016 Protonic Holland > + */ > + > +/dts-v1/; > +#include "imx6dl.dtsi" > +#include "imx6qdl-prti6q.dtsi" Should we name it "imx6qdl-prt-common.dtsi"? Still don't like that this dtsi comes from the 1st commit rather then having a single commit adding the .dtsi but that is only my opinion. > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/sound/fsl-imx-audmux.h> > + > +/ { > + model = "Protonic VT7"; > + compatible = "prt,prtvt7", "fsl,imx6dl"; > + > + memory@10000000 { > + device_type = "memory"; > + reg = <0x10000000 0x20000000>; > + }; > + > + backlight_lcd: backlight-lcd { > + compatible = "pwm-backlight"; > + pwms = <&pwm1 0 500000>; > + brightness-levels = <0 20 81 248 1000>; > + default-brightness-level = <20>; > + num-interpolated-steps = <21>; Do you need this fine granularity here? Just asking ;) > + power-supply = <®_12v_bl>; > + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; Where gets this gpio muxed? > + }; > + > + display { > + compatible = "fsl,imx-parallel-display"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ipu1_disp>; > + #address-cells = <1>; > + #size-cells = <0>; > + interface-pix-fmt = "rgb24"; > + status = "okay"; Status not needed here. > + > + port@0 { > + reg = <0>; > + > + display_in: endpoint { > + remote-endpoint = <&ipu1_di0_disp0>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + display_out: endpoint { > + remote-endpoint = <&panel_in>; > + }; > + }; > + }; > + > + keys { > + compatible = "gpio-keys"; > + autorepeat; > + > + esc { > + label = "GPIO Key ESC"; > + linux,code = <KEY_ESC>; > + gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>; > + }; > + > + up { > + label = "GPIO Key UP"; > + linux,code = <KEY_UP>; > + gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>; > + }; > + > + down { > + label = "GPIO Key DOWN"; > + linux,code = <KEY_DOWN>; > + gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>; > + }; > + > + enter { > + label = "GPIO Key Enter"; > + linux,code = <KEY_ENTER>; > + gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>; > + }; > + > + cycle { > + label = "GPIO Key CYCLE"; > + linux,code = <KEY_CYCLEWINDOWS>; > + gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>; > + }; > + > + f1 { > + label = "GPIO Key F1"; > + linux,code = <KEY_F1>; > + gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>; > + }; > + > + f2 { > + label = "GPIO Key F2"; > + linux,code = <KEY_F2>; > + gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>; > + }; > + > + f3 { > + label = "GPIO Key F3"; > + linux,code = <KEY_F3>; > + gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>; > + }; > + > + f4 { > + label = "GPIO Key F4"; > + linux,code = <KEY_F4>; > + gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>; > + }; > + > + f5 { > + label = "GPIO Key F5"; > + linux,code = <KEY_F5>; > + gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>; > + }; > + > + f6 { > + label = "GPIO Key F6"; > + linux,code = <KEY_F6>; > + gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>; > + }; > + > + f7 { > + label = "GPIO Key F7"; > + linux,code = <KEY_F7>; > + gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>; > + }; > + > + f8 { > + label = "GPIO Key F8"; > + linux,code = <KEY_F8>; > + gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>; > + }; > + > + f9 { > + label = "GPIO Key F9"; > + linux,code = <KEY_F9>; > + gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>; > + }; > + > + f10 { > + label = "GPIO Key F10"; > + linux,code = <KEY_F10>; > + gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>; > + }; Don't know if there is a common rule if the gpio key should be sorted alphabetical too. > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_leds>; > + > + led-debug0 { > + function = LED_FUNCTION_STATUS; > + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + }; > + }; > + > + panel { > + compatible = "innolux,g070y2t0ec"; Did you send a patch for this panel? > + backlight = <&backlight_lcd>; > + > + port { > + panel_in: endpoint { > + remote-endpoint = <&display_out>; > + }; > + }; > + }; > + > + reg_12v_bl: regulator-bl-12v { Nit, it's common to allign the pahndle and the name, so either: reg_12v_bl -> regulator-12v-bl or reg_bl_12v -> regulator-bl-12v also it would be cool to keep the first digit after the point like you did it for the 1.8 regulator. So the result would be: reg_12v0_bl -> regulator-12v0-bl or reg_bl_12v0 -> regulator-bl-12v0 > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_reg_12v_bl>; > + regulator-name = "12v-bl"; > + regulator-min-microvolt = <12000000>; > + regulator-max-microvolt = <12000000>; > + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_1v8: regulator-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + sound { > + compatible = "simple-audio-card"; > + simple-audio-card,name = "prti6q-sgtl5000"; > + simple-audio-card,format = "i2s"; > + simple-audio-card,widgets = > + "Microphone", "Microphone Jack", > + "Line", "Line In Jack", > + "Headphone", "Headphone Jack", > + "Speaker", "External Speaker"; > + simple-audio-card,routing = > + "MIC_IN", "Microphone Jack", > + "LINE_IN", "Line In Jack", > + "Headphone Jack", "HP_OUT", > + "External Speaker", "LINE_OUT"; > + > + simple-audio-card,cpu { > + sound-dai = <&ssi1>; > + system-clock-frequency = <0>; > + }; > + > + simple-audio-card,codec { > + sound-dai = <&sgtl5000>; > + bitclock-master; > + frame-master; > + }; > + }; > +}; > + > +&clks { > + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>; > + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>; > +}; > + > +&ecspi2 { > + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi2>; > + status = "okay"; > + > + tsc@0 { > + compatible = "ti,tsc2046"; > + reg = <0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_tsc>; > + spi-max-frequency = <100000>; > + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>; The this should be listed within the binding doc. > + pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>; IRQ and the GPIO are the same gpio line? > + vcc-supply = <®_3v3>; > + > + ti,vref-delay-usecs = /bits/ 16 <100>; > + > + ti,x-min = /bits/ 16 <0>; > + ti,x-max = /bits/ 16 <8000>; > + ti,y-min = /bits/ 16 <0>; > + ti,y-max = /bits/ 16 <4800>; > + ti,x-plate-ohms = /bits/ 16 <800>; > + ti,y-plate-ohms = /bits/ 16 <300>; > + ti,pressure-max = /bits/ 16 <4095>; > + > + ti,skip-samples = <2>; > + ti,sample-period-msecs = <10>; > + ti,report-period-msecs = <30>; > + > + ti,filter-tolerance = <80>; > + ti,touch-resistance-threshold = <3500>; > + }; > +}; > + > +&audmux { Pls, sort it alphabetical. > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_audmux>; > + status = "okay"; > + > + mux_ssi1 { > + fsl,audmux-port = <0>; > + fsl,port-config = < > + IMX_AUDMUX_V2_PTCR_SYN 0 > + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0 > + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0 > + IMX_AUDMUX_V2_PTCR_TFSDIR 0 > + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2) > + >; > + }; > + > + mux_pins3 { > + fsl,audmux-port = <2>; > + fsl,port-config = < > + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0) > + 0 IMX_AUDMUX_V2_PDCR_TXRXEN > + >; > + }; > +}; > + > +&can1 { This here too. > + pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>; > +}; > + > +&i2c1 { > + sgtl5000: codec@a { > + compatible = "fsl,sgtl5000"; > + reg = <0xa>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_codec>; > + #sound-dai-cells = <0>; > + clocks = <&clks 201>; > + VDDA-supply = <®_3v3>; > + VDDIO-supply = <®_3v3>; > + VDDD-supply = <®_1v8>; > + }; > +}; > + > +&i2c3 { > + rtc@51 { > + compatible = "nxp,pcf8563"; > + reg = <0x51>; > + }; > + > + gpio_pca: gpio@74 { > + compatible = "nxp,pca9539"; > + reg = <0x74>; > + interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>; > + #gpio-cells = <2>; > + gpio-controller; > + }; > +}; > + > +&ipu1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ipu1_csi0>; > + status = "okay"; > +}; > + > +&ipu1_di0_disp0 { > + remote-endpoint = <&display_in>; > +}; > + > +&pwm1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm1>; > + status = "okay"; > +}; > + > +&snvs_poweroff { > + status = "okay"; > +}; > + > +&snvs_pwrkey { > + status = "okay"; > +}; > + > +&ssi1 { > + #sound-dai-cells = <0>; > + fsl,mode = "i2s-slave"; > + status = "okay"; > +}; > + > +&usbh1 { > + status = "disabled"; > +}; > + > +&vpu { > + status = "disabled"; > +}; Why do you disable this nodes? You should drop it from the common .dtsi if you disable them more than once. > +&iomuxc { > + pinctrl_audmux: audmuxgrp { > + fsl,pins = < > + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0 > + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 > + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 > + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 > + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 > + >; > + }; > + > + pinctrl_can1phy: can1phy { > + fsl,pins = < > + /* CAN1_SR */ > + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070 > + /* CAN1_TERM */ > + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 > + >; > + }; > + > + pinctrl_codec: codecgrp { > + fsl,pins = < > + /* AUDIO_nRESET */ > + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0 > + >; > + }; > + > + pinctrl_ecspi2: ecspi2grp { > + fsl,pins = < > + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1 > + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1 > + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1 > + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1 > + >; > + }; > + > + pinctrl_ipu1_csi0: ipu1csi0grp { > + fsl,pins = < > + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0 > + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0 > + /* ITU656_nRESET */ > + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 > + /* ITU656_nPDN */ > + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0 > + >; > + }; Why do you mux the the camera interface and have no camera device within this dt. > + pinctrl_ipu1_disp: ipudisp1grp { > + fsl,pins = < > + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0 > + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0 > + > + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0 > + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0 > + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0 > + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0 > + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0 > + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0 > + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0 > + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0 > + > + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0 > + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0 > + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0 > + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0 > + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0 > + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0 > + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0 > + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0 > + > + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0 > + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0 > + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0 > + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0 > + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0 > + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0 > + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0 > + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0 > + >; > + }; > + > + pinctrl_leds: ledsgrp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 > + >; > + }; > + > + pinctrl_pwm1: pwm1grp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0 > + >; > + }; > + > + pinctrl_reg_12v_bl: 12blgrp { Pls, keep the name scheme like the others. Regards, Marco > + fsl,pins = < > + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0 > + >; > + }; > + > + pinctrl_tsc: tscgrp { > + > + fsl,pins = < > + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0 > + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 > + >; > + }; > +};
Hi Oleksij, On 20-04-22 09:04, Marco Felsch wrote: > Hi Oleksij, > > On 20-04-21 14:40, Oleksij Rempel wrote: ... > > + reg_1v8: regulator-1v8 { > > + compatible = "regulator-fixed"; > > + regulator-name = "1v8"; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-always-on; > > + }; Just noticed that this regulator is part of the common .dtsi too, so we can drop it here. Regards, Marco
Hi Marco, Just chiming in with the answers I know most of... On Wed, 22 Apr 2020 09:04:41 +0200 Marco Felsch <m.felsch@pengutronix.de> wrote: > Hi Oleksij, > > On 20-04-21 14:40, Oleksij Rempel wrote: > > The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch > > touchscreen display. > > > > Reviewed-by: Rob Herring <robh@kernel.org> > > Signed-off-by: Robin van der Gracht <robin@protonic.nl> > > Signed-off-by: David Jander <david@protonic.nl> > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > > --- > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/imx6dl-prtvt7.dts | 472 ++++++++++++++++++++++++++++ > > 2 files changed, 473 insertions(+) > > create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index 8ce744f1cbfc9..66ee89e7929f9 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > @@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > > imx6dl-pico-hobbit.dtb \ > > imx6dl-pico-nymph.dtb \ > > imx6dl-pico-pi.dtb \ > > + imx6dl-prtvt7.dtb \ > > imx6dl-rex-basic.dtb \ > > imx6dl-riotboard.dtb \ > > imx6dl-sabreauto.dtb \ > > diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts > > new file mode 100644 > > index 0000000000000..a948c7c6eb3ce > > --- /dev/null > > +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts > > @@ -0,0 +1,472 @@ > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > > +/* > > + * Copyright (c) 2016 Protonic Holland > > + */ > > + > > +/dts-v1/; > > +#include "imx6dl.dtsi" > > +#include "imx6qdl-prti6q.dtsi" > > Should we name it "imx6qdl-prt-common.dtsi"? Still don't like that this > dtsi comes from the 1st commit rather then having a single commit adding > the .dtsi but that is only my opinion. Isn't the extension ".dtsi" implying "common" already? This file is strictly common to the "prti6q" family of products, not to all Protonic products, so the name you suggest would be potentially misleading I guess. Maybe we can just leave it like this? > > +#include <dt-bindings/input/input.h> > > +#include <dt-bindings/leds/common.h> > > +#include <dt-bindings/sound/fsl-imx-audmux.h> > > + > > +/ { > > + model = "Protonic VT7"; > > + compatible = "prt,prtvt7", "fsl,imx6dl"; > > + > > + memory@10000000 { > > + device_type = "memory"; > > + reg = <0x10000000 0x20000000>; > > + }; > > + > > + backlight_lcd: backlight-lcd { > > + compatible = "pwm-backlight"; > > + pwms = <&pwm1 0 500000>; > > + brightness-levels = <0 20 81 248 1000>; > > + default-brightness-level = <20>; > > + num-interpolated-steps = <21>; > > Do you need this fine granularity here? Just asking ;) Yes. These amount of steps are needed. > > + power-supply = <®_12v_bl>; > > + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; > > Where gets this gpio muxed? In imx6qdl-prti6q.dtsi > > + }; > > + > > + display { > > + compatible = "fsl,imx-parallel-display"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_ipu1_disp>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + interface-pix-fmt = "rgb24"; > > + status = "okay"; > > Status not needed here. Ack. > > + > > + port@0 { > > + reg = <0>; > > + > > + display_in: endpoint { > > + remote-endpoint = <&ipu1_di0_disp0>; > > + }; > > + }; > > + > > + port@1 { > > + reg = <1>; > > + > > + display_out: endpoint { > > + remote-endpoint = <&panel_in>; > > + }; > > + }; > > + }; > > + > > + keys { > > + compatible = "gpio-keys"; > > + autorepeat; > > + > > + esc { > > + label = "GPIO Key ESC"; > > + linux,code = <KEY_ESC>; > > + gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>; > > + }; > > + > > + up { > > + label = "GPIO Key UP"; > > + linux,code = <KEY_UP>; > > + gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>; > > + }; > > + > > + down { > > + label = "GPIO Key DOWN"; > > + linux,code = <KEY_DOWN>; > > + gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>; > > + }; > > + > > + enter { > > + label = "GPIO Key Enter"; > > + linux,code = <KEY_ENTER>; > > + gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>; > > + }; > > + > > + cycle { > > + label = "GPIO Key CYCLE"; > > + linux,code = <KEY_CYCLEWINDOWS>; > > + gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>; > > + }; > > + > > + f1 { > > + label = "GPIO Key F1"; > > + linux,code = <KEY_F1>; > > + gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>; > > + }; > > + > > + f2 { > > + label = "GPIO Key F2"; > > + linux,code = <KEY_F2>; > > + gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>; > > + }; > > + > > + f3 { > > + label = "GPIO Key F3"; > > + linux,code = <KEY_F3>; > > + gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>; > > + }; > > + > > + f4 { > > + label = "GPIO Key F4"; > > + linux,code = <KEY_F4>; > > + gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>; > > + }; > > + > > + f5 { > > + label = "GPIO Key F5"; > > + linux,code = <KEY_F5>; > > + gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>; > > + }; > > + > > + f6 { > > + label = "GPIO Key F6"; > > + linux,code = <KEY_F6>; > > + gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>; > > + }; > > + > > + f7 { > > + label = "GPIO Key F7"; > > + linux,code = <KEY_F7>; > > + gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>; > > + }; > > + > > + f8 { > > + label = "GPIO Key F8"; > > + linux,code = <KEY_F8>; > > + gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>; > > + }; > > + > > + f9 { > > + label = "GPIO Key F9"; > > + linux,code = <KEY_F9>; > > + gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>; > > + }; > > + > > + f10 { > > + label = "GPIO Key F10"; > > + linux,code = <KEY_F10>; > > + gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>; > > + }; > > Don't know if there is a common rule if the gpio key should be sorted > alphabetical too. > > > + }; > > + > > + leds { > > + compatible = "gpio-leds"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_leds>; > > + > > + led-debug0 { > > + function = LED_FUNCTION_STATUS; > > + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; > > + linux,default-trigger = "heartbeat"; > > + }; > > + }; > > + > > + panel { > > + compatible = "innolux,g070y2t0ec"; > > Did you send a patch for this panel? Good catch. Yes, there is a patch for this panel. Maybe that patch should come first, Oleksij? > > + backlight = <&backlight_lcd>; > > + > > + port { > > + panel_in: endpoint { > > + remote-endpoint = <&display_out>; > > + }; > > + }; > > + }; > > + > > + reg_12v_bl: regulator-bl-12v { > > Nit, it's common to allign the pahndle and the name, so either: > > reg_12v_bl -> regulator-12v-bl > > or > > reg_bl_12v -> regulator-bl-12v > > also it would be cool to keep the first digit after the point like you > did it for the 1.8 regulator. So the result would be: > > reg_12v0_bl -> regulator-12v0-bl > > or > > reg_bl_12v0 -> regulator-bl-12v0 I'm not strictly against it, but isn't the implicit rule "All significant digits, with a minimum of 2" even better here? Just saying... 12000v0 would look a bit awkward ;-) > > + compatible = "regulator-fixed"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_reg_12v_bl>; > > + regulator-name = "12v-bl"; > > + regulator-min-microvolt = <12000000>; > > + regulator-max-microvolt = <12000000>; > > + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + }; > > + > > + reg_1v8: regulator-1v8 { > > + compatible = "regulator-fixed"; > > + regulator-name = "1v8"; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-always-on; > > + }; > > + > > + sound { > > + compatible = "simple-audio-card"; > > + simple-audio-card,name = "prti6q-sgtl5000"; > > + simple-audio-card,format = "i2s"; > > + simple-audio-card,widgets = > > + "Microphone", "Microphone Jack", > > + "Line", "Line In Jack", > > + "Headphone", "Headphone Jack", > > + "Speaker", "External Speaker"; > > + simple-audio-card,routing = > > + "MIC_IN", "Microphone Jack", > > + "LINE_IN", "Line In Jack", > > + "Headphone Jack", "HP_OUT", > > + "External Speaker", "LINE_OUT"; > > + > > + simple-audio-card,cpu { > > + sound-dai = <&ssi1>; > > + system-clock-frequency = <0>; > > + }; > > + > > + simple-audio-card,codec { > > + sound-dai = <&sgtl5000>; > > + bitclock-master; > > + frame-master; > > + }; > > + }; > > +}; > > + > > +&clks { > > + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>; > > + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>; > > +}; > > + > > +&ecspi2 { > > + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_ecspi2>; > > + status = "okay"; > > + > > + tsc@0 { > > + compatible = "ti,tsc2046"; > > + reg = <0>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_tsc>; > > + spi-max-frequency = <100000>; > > + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>; > > The this should be listed within the binding doc. > > > + pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>; > > IRQ and the GPIO are the same gpio line? Yes, this driver uses the same GPIO as interrupt and also as a GPIO. A bit strange, I agree. It is the same pin on the TS controller. > > + vcc-supply = <®_3v3>; > > + > > + ti,vref-delay-usecs = /bits/ 16 <100>; > > + > > + ti,x-min = /bits/ 16 <0>; > > + ti,x-max = /bits/ 16 <8000>; > > + ti,y-min = /bits/ 16 <0>; > > + ti,y-max = /bits/ 16 <4800>; > > + ti,x-plate-ohms = /bits/ 16 <800>; > > + ti,y-plate-ohms = /bits/ 16 <300>; > > + ti,pressure-max = /bits/ 16 <4095>; > > + > > + ti,skip-samples = <2>; > > + ti,sample-period-msecs = <10>; > > + ti,report-period-msecs = <30>; > > + > > + ti,filter-tolerance = <80>; > > + ti,touch-resistance-threshold = <3500>; Now that I see this, this DT node corresponds to a rewritten version of the ads7846 touchscreen driver, which probably also should precede this patch? The original driver is horribly buggy, and I have submitted patches twice already long ago to input mailing list, but unfortunately it got completely ignored both times. > > + }; > > +}; > > + > > +&audmux { > > Pls, sort it alphabetical. > > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_audmux>; > > + status = "okay"; > > + > > + mux_ssi1 { > > + fsl,audmux-port = <0>; > > + fsl,port-config = < > > + IMX_AUDMUX_V2_PTCR_SYN 0 > > + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0 > > + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0 > > + IMX_AUDMUX_V2_PTCR_TFSDIR 0 > > + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2) > > + >; > > + }; > > + > > + mux_pins3 { > > + fsl,audmux-port = <2>; > > + fsl,port-config = < > > + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0) > > + 0 IMX_AUDMUX_V2_PDCR_TXRXEN > > + >; > > + }; > > +}; > > + > > +&can1 { > > This here too. > > > + pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>; > > +}; > > + > > +&i2c1 { > > + sgtl5000: codec@a { > > + compatible = "fsl,sgtl5000"; > > + reg = <0xa>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_codec>; > > + #sound-dai-cells = <0>; > > + clocks = <&clks 201>; > > + VDDA-supply = <®_3v3>; > > + VDDIO-supply = <®_3v3>; > > + VDDD-supply = <®_1v8>; > > + }; > > +}; > > + > > +&i2c3 { > > + rtc@51 { > > + compatible = "nxp,pcf8563"; > > + reg = <0x51>; > > + }; > > + > > + gpio_pca: gpio@74 { > > + compatible = "nxp,pca9539"; > > + reg = <0x74>; > > + interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>; > > + #gpio-cells = <2>; > > + gpio-controller; > > + }; > > +}; > > + > > +&ipu1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_ipu1_csi0>; > > + status = "okay"; > > +}; > > + > > +&ipu1_di0_disp0 { > > + remote-endpoint = <&display_in>; > > +}; > > + > > +&pwm1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_pwm1>; > > + status = "okay"; > > +}; > > + > > +&snvs_poweroff { > > + status = "okay"; > > +}; > > + > > +&snvs_pwrkey { > > + status = "okay"; > > +}; > > + > > +&ssi1 { > > + #sound-dai-cells = <0>; > > + fsl,mode = "i2s-slave"; > > + status = "okay"; > > +}; > > + > > +&usbh1 { > > + status = "disabled"; > > +}; > > + > > +&vpu { > > + status = "disabled"; > > +}; > > Why do you disable this nodes? You should drop it from the common .dtsi > if you disable them more than once. We should have to count the enables and disables, and decide which solution ends up with less lines of code overall, I suppose. Our boards DT's are built in a kind of class hierarchy. There are a total of 16+ different i.MX6 boards. Almost all of them inherit from PRTI6Q, and some have other, higher-order ancestors. Oleksij is busy with the first few of them right now. We can optimize all inheritances for the few boards that are being submitted now, but if the rest will follow, the end result might either be less than optimal, or this will need to change again. > > +&iomuxc { > > + pinctrl_audmux: audmuxgrp { > > + fsl,pins = < > > + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0 > > + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 > > + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 > > + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 > > + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 > > + >; > > + }; > > + > > + pinctrl_can1phy: can1phy { > > + fsl,pins = < > > + /* CAN1_SR */ > > + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070 > > + /* CAN1_TERM */ > > + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 > > + >; > > + }; > > + > > + pinctrl_codec: codecgrp { > > + fsl,pins = < > > + /* AUDIO_nRESET */ > > + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0 > > + >; > > + }; > > + > > + pinctrl_ecspi2: ecspi2grp { > > + fsl,pins = < > > + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1 > > + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1 > > + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1 > > + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1 > > + >; > > + }; > > + > > + pinctrl_ipu1_csi0: ipu1csi0grp { > > + fsl,pins = < > > + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0 > > + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0 > > + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0 > > + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0 > > + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0 > > + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0 > > + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0 > > + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0 > > + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0 > > + /* ITU656_nRESET */ > > + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 > > + /* ITU656_nPDN */ > > + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0 > > + >; > > + }; > > Why do you mux the the camera interface and have no camera device within > this dt. Because the camera requires more patches that are on the way to mainline, but not there yet. Maybe for now these should be removed? > > + pinctrl_ipu1_disp: ipudisp1grp { > > + fsl,pins = < > > + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0 > > + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0 > > + > > + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0 > > + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0 > > + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0 > > + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0 > > + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0 > > + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0 > > + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0 > > + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0 > > + > > + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0 > > + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0 > > + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0 > > + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0 > > + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0 > > + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0 > > + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0 > > + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0 > > + > > + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0 > > + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0 > > + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0 > > + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0 > > + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0 > > + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0 > > + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0 > > + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0 > > + >; > > + }; > > + > > + pinctrl_leds: ledsgrp { > > + fsl,pins = < > > + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 > > + >; > > + }; > > + > > + pinctrl_pwm1: pwm1grp { > > + fsl,pins = < > > + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0 > > + >; > > + }; > > + > > + pinctrl_reg_12v_bl: 12blgrp { > > Pls, keep the name scheme like the others. > > Regards, > Marco > > > + fsl,pins = < > > + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0 > > + >; > > + }; > > + > > + pinctrl_tsc: tscgrp { > > + > > + fsl,pins = < > > + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0 > > + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 > > + >; > > + }; > > +}; Best regards,
I David, On 20-04-22 11:38, David Jander wrote: > > Hi Marco, > > Just chiming in with the answers I know most of... Thanks for your reponse =) > On Wed, 22 Apr 2020 09:04:41 +0200 > Marco Felsch <m.felsch@pengutronix.de> wrote: > > > Hi Oleksij, > > > > On 20-04-21 14:40, Oleksij Rempel wrote: > > > The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch > > > touchscreen display. > > > > > > Reviewed-by: Rob Herring <robh@kernel.org> > > > Signed-off-by: Robin van der Gracht <robin@protonic.nl> > > > Signed-off-by: David Jander <david@protonic.nl> > > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > > > --- > > > arch/arm/boot/dts/Makefile | 1 + > > > arch/arm/boot/dts/imx6dl-prtvt7.dts | 472 ++++++++++++++++++++++++++++ > > > 2 files changed, 473 insertions(+) > > > create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts > > > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > > index 8ce744f1cbfc9..66ee89e7929f9 100644 > > > --- a/arch/arm/boot/dts/Makefile > > > +++ b/arch/arm/boot/dts/Makefile > > > @@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > > > imx6dl-pico-hobbit.dtb \ > > > imx6dl-pico-nymph.dtb \ > > > imx6dl-pico-pi.dtb \ > > > + imx6dl-prtvt7.dtb \ > > > imx6dl-rex-basic.dtb \ > > > imx6dl-riotboard.dtb \ > > > imx6dl-sabreauto.dtb \ > > > diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts > > > new file mode 100644 > > > index 0000000000000..a948c7c6eb3ce > > > --- /dev/null > > > +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts > > > @@ -0,0 +1,472 @@ > > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > > > +/* > > > + * Copyright (c) 2016 Protonic Holland > > > + */ > > > + > > > +/dts-v1/; > > > +#include "imx6dl.dtsi" > > > +#include "imx6qdl-prti6q.dtsi" > > > > Should we name it "imx6qdl-prt-common.dtsi"? Still don't like that this > > dtsi comes from the 1st commit rather then having a single commit adding > > the .dtsi but that is only my opinion. > > Isn't the extension ".dtsi" implying "common" already? > This file is strictly common to the "prti6q" family of products, not to all > Protonic products, so the name you suggest would be potentially misleading I > guess. Maybe we can just leave it like this? It was just a suggestion. It's not that obvious that the WD2 is part of the PRTI6Q family for outsiders. > > > +#include <dt-bindings/input/input.h> > > > +#include <dt-bindings/leds/common.h> > > > +#include <dt-bindings/sound/fsl-imx-audmux.h> > > > + > > > +/ { > > > + model = "Protonic VT7"; > > > + compatible = "prt,prtvt7", "fsl,imx6dl"; > > > + > > > + memory@10000000 { > > > + device_type = "memory"; > > > + reg = <0x10000000 0x20000000>; > > > + }; > > > + > > > + backlight_lcd: backlight-lcd { > > > + compatible = "pwm-backlight"; > > > + pwms = <&pwm1 0 500000>; > > > + brightness-levels = <0 20 81 248 1000>; > > > + default-brightness-level = <20>; > > > + num-interpolated-steps = <21>; > > > > Do you need this fine granularity here? Just asking ;) > > Yes. These amount of steps are needed. > > > > + power-supply = <®_12v_bl>; > > > + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; > > > > Where gets this gpio muxed? > > In imx6qdl-prti6q.dtsi Yep, thanks for the link. So you override here the complete node since it has the extact name. What do you want to change here and why didn't you use phandle from the .dtsi? > > > + }; > > > + > > > + display { > > > + compatible = "fsl,imx-parallel-display"; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_ipu1_disp>; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + interface-pix-fmt = "rgb24"; > > > + status = "okay"; > > > > Status not needed here. > > Ack. > > > > + > > > + port@0 { > > > + reg = <0>; > > > + > > > + display_in: endpoint { > > > + remote-endpoint = <&ipu1_di0_disp0>; > > > + }; > > > + }; > > > + > > > + port@1 { > > > + reg = <1>; > > > + > > > + display_out: endpoint { > > > + remote-endpoint = <&panel_in>; > > > + }; > > > + }; > > > + }; > > > + > > > + keys { > > > + compatible = "gpio-keys"; > > > + autorepeat; > > > + > > > + esc { > > > + label = "GPIO Key ESC"; > > > + linux,code = <KEY_ESC>; > > > + gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + up { > > > + label = "GPIO Key UP"; > > > + linux,code = <KEY_UP>; > > > + gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + down { > > > + label = "GPIO Key DOWN"; > > > + linux,code = <KEY_DOWN>; > > > + gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + enter { > > > + label = "GPIO Key Enter"; > > > + linux,code = <KEY_ENTER>; > > > + gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + cycle { > > > + label = "GPIO Key CYCLE"; > > > + linux,code = <KEY_CYCLEWINDOWS>; > > > + gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + f1 { > > > + label = "GPIO Key F1"; > > > + linux,code = <KEY_F1>; > > > + gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + f2 { > > > + label = "GPIO Key F2"; > > > + linux,code = <KEY_F2>; > > > + gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + f3 { > > > + label = "GPIO Key F3"; > > > + linux,code = <KEY_F3>; > > > + gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + f4 { > > > + label = "GPIO Key F4"; > > > + linux,code = <KEY_F4>; > > > + gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + f5 { > > > + label = "GPIO Key F5"; > > > + linux,code = <KEY_F5>; > > > + gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + f6 { > > > + label = "GPIO Key F6"; > > > + linux,code = <KEY_F6>; > > > + gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + f7 { > > > + label = "GPIO Key F7"; > > > + linux,code = <KEY_F7>; > > > + gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + f8 { > > > + label = "GPIO Key F8"; > > > + linux,code = <KEY_F8>; > > > + gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + f9 { > > > + label = "GPIO Key F9"; > > > + linux,code = <KEY_F9>; > > > + gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>; > > > + }; > > > + > > > + f10 { > > > + label = "GPIO Key F10"; > > > + linux,code = <KEY_F10>; > > > + gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>; > > > + }; > > > > Don't know if there is a common rule if the gpio key should be sorted > > alphabetical too. > > > > > + }; > > > + > > > + leds { > > > + compatible = "gpio-leds"; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_leds>; > > > + > > > + led-debug0 { > > > + function = LED_FUNCTION_STATUS; > > > + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; > > > + linux,default-trigger = "heartbeat"; > > > + }; > > > + }; > > > + > > > + panel { > > > + compatible = "innolux,g070y2t0ec"; > > > > Did you send a patch for this panel? > > Good catch. Yes, there is a patch for this panel. Maybe that patch should come > first, Oleksij? I would appreciate this. It happens often that drivers are not mainlined yet but patches are on the ML and on their way to mainline. > > > + backlight = <&backlight_lcd>; > > > + > > > + port { > > > + panel_in: endpoint { > > > + remote-endpoint = <&display_out>; > > > + }; > > > + }; > > > + }; > > > + > > > + reg_12v_bl: regulator-bl-12v { > > > > Nit, it's common to allign the pahndle and the name, so either: > > > > reg_12v_bl -> regulator-12v-bl > > > > or > > > > reg_bl_12v -> regulator-bl-12v > > > > also it would be cool to keep the first digit after the point like you > > did it for the 1.8 regulator. So the result would be: > > > > reg_12v0_bl -> regulator-12v0-bl > > > > or > > > > reg_bl_12v0 -> regulator-bl-12v0 > > I'm not strictly against it, but isn't the implicit rule "All significant > digits, with a minimum of 2" even better here? Just saying... 12000v0 would > look a bit awkward ;-) Yep, that looks a bit awkward.. What I wanted to say is to keep the style over the DTs and don't mix them. > > > + compatible = "regulator-fixed"; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_reg_12v_bl>; > > > + regulator-name = "12v-bl"; > > > + regulator-min-microvolt = <12000000>; > > > + regulator-max-microvolt = <12000000>; > > > + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; > > > + enable-active-high; > > > + }; > > > + > > > + reg_1v8: regulator-1v8 { > > > + compatible = "regulator-fixed"; > > > + regulator-name = "1v8"; > > > + regulator-min-microvolt = <1800000>; > > > + regulator-max-microvolt = <1800000>; > > > + regulator-always-on; > > > + }; > > > + > > > + sound { > > > + compatible = "simple-audio-card"; > > > + simple-audio-card,name = "prti6q-sgtl5000"; > > > + simple-audio-card,format = "i2s"; > > > + simple-audio-card,widgets = > > > + "Microphone", "Microphone Jack", > > > + "Line", "Line In Jack", > > > + "Headphone", "Headphone Jack", > > > + "Speaker", "External Speaker"; > > > + simple-audio-card,routing = > > > + "MIC_IN", "Microphone Jack", > > > + "LINE_IN", "Line In Jack", > > > + "Headphone Jack", "HP_OUT", > > > + "External Speaker", "LINE_OUT"; > > > + > > > + simple-audio-card,cpu { > > > + sound-dai = <&ssi1>; > > > + system-clock-frequency = <0>; > > > + }; > > > + > > > + simple-audio-card,codec { > > > + sound-dai = <&sgtl5000>; > > > + bitclock-master; > > > + frame-master; > > > + }; > > > + }; > > > +}; > > > + > > > +&clks { > > > + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>; > > > + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>; > > > +}; > > > + > > > +&ecspi2 { > > > + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_ecspi2>; > > > + status = "okay"; > > > + > > > + tsc@0 { > > > + compatible = "ti,tsc2046"; > > > + reg = <0>; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_tsc>; > > > + spi-max-frequency = <100000>; > > > + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>; > > > > The this should be listed within the binding doc. > > > > > + pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>; > > > > IRQ and the GPIO are the same gpio line? > > Yes, this driver uses the same GPIO as interrupt and also as a GPIO. A bit > strange, I agree. It is the same pin on the TS controller. > > > > + vcc-supply = <®_3v3>; > > > + > > > + ti,vref-delay-usecs = /bits/ 16 <100>; > > > + > > > + ti,x-min = /bits/ 16 <0>; > > > + ti,x-max = /bits/ 16 <8000>; > > > + ti,y-min = /bits/ 16 <0>; > > > + ti,y-max = /bits/ 16 <4800>; > > > + ti,x-plate-ohms = /bits/ 16 <800>; > > > + ti,y-plate-ohms = /bits/ 16 <300>; > > > + ti,pressure-max = /bits/ 16 <4095>; > > > + > > > + ti,skip-samples = <2>; > > > + ti,sample-period-msecs = <10>; > > > + ti,report-period-msecs = <30>; > > > + > > > + ti,filter-tolerance = <80>; > > > + ti,touch-resistance-threshold = <3500>; > > Now that I see this, this DT node corresponds to a rewritten version of the > ads7846 touchscreen driver, which probably also should precede this patch? > The original driver is horribly buggy, and I have submitted patches twice > already long ago to input mailing list, but unfortunately it got completely > ignored both times. Pls, can you resend the patches with cc me or give me some pointers? So we can give them another try. > > > + }; > > > +}; > > > + > > > +&audmux { > > > > Pls, sort it alphabetical. > > > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_audmux>; > > > + status = "okay"; > > > + > > > + mux_ssi1 { > > > + fsl,audmux-port = <0>; > > > + fsl,port-config = < > > > + IMX_AUDMUX_V2_PTCR_SYN 0 > > > + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0 > > > + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0 > > > + IMX_AUDMUX_V2_PTCR_TFSDIR 0 > > > + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2) > > > + >; > > > + }; > > > + > > > + mux_pins3 { > > > + fsl,audmux-port = <2>; > > > + fsl,port-config = < > > > + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0) > > > + 0 IMX_AUDMUX_V2_PDCR_TXRXEN > > > + >; > > > + }; > > > +}; > > > + > > > +&can1 { > > > > This here too. > > > > > + pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>; > > > +}; > > > + > > > +&i2c1 { > > > + sgtl5000: codec@a { > > > + compatible = "fsl,sgtl5000"; > > > + reg = <0xa>; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_codec>; > > > + #sound-dai-cells = <0>; > > > + clocks = <&clks 201>; > > > + VDDA-supply = <®_3v3>; > > > + VDDIO-supply = <®_3v3>; > > > + VDDD-supply = <®_1v8>; > > > + }; > > > +}; > > > + > > > +&i2c3 { > > > + rtc@51 { > > > + compatible = "nxp,pcf8563"; > > > + reg = <0x51>; > > > + }; > > > + > > > + gpio_pca: gpio@74 { > > > + compatible = "nxp,pca9539"; > > > + reg = <0x74>; > > > + interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>; > > > + #gpio-cells = <2>; > > > + gpio-controller; > > > + }; > > > +}; > > > + > > > +&ipu1 { > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_ipu1_csi0>; > > > + status = "okay"; > > > +}; > > > + > > > +&ipu1_di0_disp0 { > > > + remote-endpoint = <&display_in>; > > > +}; > > > + > > > +&pwm1 { > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_pwm1>; > > > + status = "okay"; > > > +}; > > > + > > > +&snvs_poweroff { > > > + status = "okay"; > > > +}; > > > + > > > +&snvs_pwrkey { > > > + status = "okay"; > > > +}; > > > + > > > +&ssi1 { > > > + #sound-dai-cells = <0>; > > > + fsl,mode = "i2s-slave"; > > > + status = "okay"; > > > +}; > > > + > > > +&usbh1 { > > > + status = "disabled"; > > > +}; > > > + > > > +&vpu { > > > + status = "disabled"; > > > +}; > > > > Why do you disable this nodes? You should drop it from the common .dtsi > > if you disable them more than once. > > We should have to count the enables and disables, and decide which solution > ends up with less lines of code overall, I suppose. > Our boards DT's are built in a kind of class hierarchy. There are a total of > 16+ different i.MX6 boards. Almost all of them inherit from PRTI6Q, and some > have other, higher-order ancestors. Oleksij is busy with the first few of them > right now. > We can optimize all inheritances for the few boards that are being submitted > now, but if the rest will follow, the end result might either be less than > optimal, or this will need to change again. I see, but I still prefer the "enable once" way since it is a bit more straight forward. But it should be no blocker.. > > > +&iomuxc { > > > + pinctrl_audmux: audmuxgrp { > > > + fsl,pins = < > > > + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0 > > > + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 > > > + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 > > > + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 > > > + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 > > > + >; > > > + }; > > > + > > > + pinctrl_can1phy: can1phy { > > > + fsl,pins = < > > > + /* CAN1_SR */ > > > + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070 > > > + /* CAN1_TERM */ > > > + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 > > > + >; > > > + }; > > > + > > > + pinctrl_codec: codecgrp { > > > + fsl,pins = < > > > + /* AUDIO_nRESET */ > > > + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0 > > > + >; > > > + }; > > > + > > > + pinctrl_ecspi2: ecspi2grp { > > > + fsl,pins = < > > > + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1 > > > + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1 > > > + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1 > > > + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1 > > > + >; > > > + }; > > > + > > > + pinctrl_ipu1_csi0: ipu1csi0grp { > > > + fsl,pins = < > > > + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0 > > > + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0 > > > + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0 > > > + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0 > > > + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0 > > > + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0 > > > + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0 > > > + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0 > > > + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0 > > > + /* ITU656_nRESET */ > > > + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 > > > + /* ITU656_nPDN */ > > > + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0 > > > + >; > > > + }; > > > > Why do you mux the the camera interface and have no camera device within > > this dt. > > Because the camera requires more patches that are on the way to mainline, but > not there yet. Maybe for now these should be removed? Adding the muxing later would be the better way. Regards, Marco > > > + pinctrl_ipu1_disp: ipudisp1grp { > > > + fsl,pins = < > > > + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0 > > > + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0 > > > + > > > + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0 > > > + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0 > > > + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0 > > > + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0 > > > + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0 > > > + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0 > > > + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0 > > > + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0 > > > + > > > + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0 > > > + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0 > > > + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0 > > > + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0 > > > + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0 > > > + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0 > > > + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0 > > > + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0 > > > + > > > + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0 > > > + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0 > > > + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0 > > > + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0 > > > + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0 > > > + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0 > > > + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0 > > > + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0 > > > + >; > > > + }; > > > + > > > + pinctrl_leds: ledsgrp { > > > + fsl,pins = < > > > + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 > > > + >; > > > + }; > > > + > > > + pinctrl_pwm1: pwm1grp { > > > + fsl,pins = < > > > + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0 > > > + >; > > > + }; > > > + > > > + pinctrl_reg_12v_bl: 12blgrp { > > > > Pls, keep the name scheme like the others. > > > > Regards, > > Marco > > > > > + fsl,pins = < > > > + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0 > > > + >; > > > + }; > > > + > > > + pinctrl_tsc: tscgrp { > > > + > > > + fsl,pins = < > > > + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0 > > > + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 > > > + >; > > > + }; > > > +}; > > Best regards, > > -- > David Jander > Protonic Holland.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 8ce744f1cbfc9..66ee89e7929f9 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-pico-hobbit.dtb \ imx6dl-pico-nymph.dtb \ imx6dl-pico-pi.dtb \ + imx6dl-prtvt7.dtb \ imx6dl-rex-basic.dtb \ imx6dl-riotboard.dtb \ imx6dl-sabreauto.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts new file mode 100644 index 0000000000000..a948c7c6eb3ce --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts @@ -0,0 +1,472 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2016 Protonic Holland + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-prti6q.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/sound/fsl-imx-audmux.h> + +/ { + model = "Protonic VT7"; + compatible = "prt,prtvt7", "fsl,imx6dl"; + + memory@10000000 { + device_type = "memory"; + reg = <0x10000000 0x20000000>; + }; + + backlight_lcd: backlight-lcd { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 500000>; + brightness-levels = <0 20 81 248 1000>; + default-brightness-level = <20>; + num-interpolated-steps = <21>; + power-supply = <®_12v_bl>; + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; + }; + + display { + compatible = "fsl,imx-parallel-display"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ipu1_disp>; + #address-cells = <1>; + #size-cells = <0>; + interface-pix-fmt = "rgb24"; + status = "okay"; + + port@0 { + reg = <0>; + + display_in: endpoint { + remote-endpoint = <&ipu1_di0_disp0>; + }; + }; + + port@1 { + reg = <1>; + + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + + keys { + compatible = "gpio-keys"; + autorepeat; + + esc { + label = "GPIO Key ESC"; + linux,code = <KEY_ESC>; + gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>; + }; + + up { + label = "GPIO Key UP"; + linux,code = <KEY_UP>; + gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>; + }; + + down { + label = "GPIO Key DOWN"; + linux,code = <KEY_DOWN>; + gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>; + }; + + enter { + label = "GPIO Key Enter"; + linux,code = <KEY_ENTER>; + gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>; + }; + + cycle { + label = "GPIO Key CYCLE"; + linux,code = <KEY_CYCLEWINDOWS>; + gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>; + }; + + f1 { + label = "GPIO Key F1"; + linux,code = <KEY_F1>; + gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>; + }; + + f2 { + label = "GPIO Key F2"; + linux,code = <KEY_F2>; + gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>; + }; + + f3 { + label = "GPIO Key F3"; + linux,code = <KEY_F3>; + gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>; + }; + + f4 { + label = "GPIO Key F4"; + linux,code = <KEY_F4>; + gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>; + }; + + f5 { + label = "GPIO Key F5"; + linux,code = <KEY_F5>; + gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>; + }; + + f6 { + label = "GPIO Key F6"; + linux,code = <KEY_F6>; + gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>; + }; + + f7 { + label = "GPIO Key F7"; + linux,code = <KEY_F7>; + gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>; + }; + + f8 { + label = "GPIO Key F8"; + linux,code = <KEY_F8>; + gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>; + }; + + f9 { + label = "GPIO Key F9"; + linux,code = <KEY_F9>; + gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>; + }; + + f10 { + label = "GPIO Key F10"; + linux,code = <KEY_F10>; + gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-debug0 { + function = LED_FUNCTION_STATUS; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + panel { + compatible = "innolux,g070y2t0ec"; + backlight = <&backlight_lcd>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + + reg_12v_bl: regulator-bl-12v { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_12v_bl>; + regulator-name = "12v-bl"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "prti6q-sgtl5000"; + simple-audio-card,format = "i2s"; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Line", "Line In Jack", + "Headphone", "Headphone Jack", + "Speaker", "External Speaker"; + simple-audio-card,routing = + "MIC_IN", "Microphone Jack", + "LINE_IN", "Line In Jack", + "Headphone Jack", "HP_OUT", + "External Speaker", "LINE_OUT"; + + simple-audio-card,cpu { + sound-dai = <&ssi1>; + system-clock-frequency = <0>; + }; + + simple-audio-card,codec { + sound-dai = <&sgtl5000>; + bitclock-master; + frame-master; + }; + }; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>; +}; + +&ecspi2 { + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + status = "okay"; + + tsc@0 { + compatible = "ti,tsc2046"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc>; + spi-max-frequency = <100000>; + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>; + pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>; + vcc-supply = <®_3v3>; + + ti,vref-delay-usecs = /bits/ 16 <100>; + + ti,x-min = /bits/ 16 <0>; + ti,x-max = /bits/ 16 <8000>; + ti,y-min = /bits/ 16 <0>; + ti,y-max = /bits/ 16 <4800>; + ti,x-plate-ohms = /bits/ 16 <800>; + ti,y-plate-ohms = /bits/ 16 <300>; + ti,pressure-max = /bits/ 16 <4095>; + + ti,skip-samples = <2>; + ti,sample-period-msecs = <10>; + ti,report-period-msecs = <30>; + + ti,filter-tolerance = <80>; + ti,touch-resistance-threshold = <3500>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; + + mux_ssi1 { + fsl,audmux-port = <0>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN 0 + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0 + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0 + IMX_AUDMUX_V2_PTCR_TFSDIR 0 + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2) + >; + }; + + mux_pins3 { + fsl,audmux-port = <2>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0) + 0 IMX_AUDMUX_V2_PDCR_TXRXEN + >; + }; +}; + +&can1 { + pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>; +}; + +&i2c1 { + sgtl5000: codec@a { + compatible = "fsl,sgtl5000"; + reg = <0xa>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_codec>; + #sound-dai-cells = <0>; + clocks = <&clks 201>; + VDDA-supply = <®_3v3>; + VDDIO-supply = <®_3v3>; + VDDD-supply = <®_1v8>; + }; +}; + +&i2c3 { + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + gpio_pca: gpio@74 { + compatible = "nxp,pca9539"; + reg = <0x74>; + interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>; + #gpio-cells = <2>; + gpio-controller; + }; +}; + +&ipu1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ipu1_csi0>; + status = "okay"; +}; + +&ipu1_di0_disp0 { + remote-endpoint = <&display_in>; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&snvs_poweroff { + status = "okay"; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&ssi1 { + #sound-dai-cells = <0>; + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&usbh1 { + status = "disabled"; +}; + +&vpu { + status = "disabled"; +}; + +&iomuxc { + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0 + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_can1phy: can1phy { + fsl,pins = < + /* CAN1_SR */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070 + /* CAN1_TERM */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 + >; + }; + + pinctrl_codec: codecgrp { + fsl,pins = < + /* AUDIO_nRESET */ + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1 + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1 + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1 + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1 + >; + }; + + pinctrl_ipu1_csi0: ipu1csi0grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0 + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0 + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0 + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0 + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0 + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0 + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0 + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0 + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0 + /* ITU656_nRESET */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 + /* ITU656_nPDN */ + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0 + >; + }; + + pinctrl_ipu1_disp: ipudisp1grp { + fsl,pins = < + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0 + + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0 + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0 + + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0 + + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0 + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0 + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0 + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0 + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0 + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0 + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0 + >; + }; + + pinctrl_reg_12v_bl: 12blgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0 + >; + }; + + pinctrl_tsc: tscgrp { + + fsl,pins = < + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0 + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 + >; + }; +};