| Message ID | 20200514155737.12160-1-martin.kepplinger@puri.sm (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/2] arm64: dts: Add a device tree for the Librem5 phone | expand |
On 14.05.20 17:57, Martin Kepplinger wrote: > From: "Angus Ainslie (Purism)" <angus@akkea.ca> > > Add a devicetree description for the Librem 5 phone. The early batches > that have been sold are supported as well as the mass-produced device > available later this year, see https://puri.sm/products/librem-5/ > > This boots to a working console with working WWAN modem, wifi usdhc, > IMU sensor device, proximity sensor, haptic motor, gpio keys, GNSS and LEDs. > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> > Signed-off-by: Guido Günther <agx@sigxcpu.org> > --- > arch/arm64/boot/dts/freescale/Makefile | 1 + > .../boot/dts/freescale/imx8mq-librem5.dts | 1174 +++++++++++++++++ > 2 files changed, 1175 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5.dts > hi, I highly appreciate it in case you can take time to review. It's not the smallest board, but this "base" support isn't huge either. For devicetree people this is certainly easy to read and I'll be happy for any opinions, objections or Acks you might have. thanks, martin
On Thu, May 14, 2020 at 7:02 PM Martin Kepplinger <martin.kepplinger@puri.sm> wrote: > > From: "Angus Ainslie (Purism)" <angus@akkea.ca> > > Add a devicetree description for the Librem 5 phone. The early batches > that have been sold are supported as well as the mass-produced device > available later this year, see https://puri.sm/products/librem-5/ > > This boots to a working console with working WWAN modem, wifi usdhc, > IMU sensor device, proximity sensor, haptic motor, gpio keys, GNSS and LEDs. > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> > Signed-off-by: Guido Günther <agx@sigxcpu.org> For audio related part: Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Hi Martin, On 20-05-14 17:57, Martin Kepplinger wrote: > From: "Angus Ainslie (Purism)" <angus@akkea.ca> > > Add a devicetree description for the Librem 5 phone. The early batches > that have been sold are supported as well as the mass-produced device > available later this year, see https://puri.sm/products/librem-5/ > > This boots to a working console with working WWAN modem, wifi usdhc, > IMU sensor device, proximity sensor, haptic motor, gpio keys, GNSS and LEDs. > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> > Signed-off-by: Guido Günther <agx@sigxcpu.org> > --- > arch/arm64/boot/dts/freescale/Makefile | 1 + > .../boot/dts/freescale/imx8mq-librem5.dts | 1174 +++++++++++++++++ > 2 files changed, 1175 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5.dts > > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile > index cd38d04da5a7..342579121f98 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb > diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dts > new file mode 100644 > index 000000000000..95c105b4c120 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dts > @@ -0,0 +1,1174 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2018-2020 Purism SPC > + */ > + > +/dts-v1/; > + > +#include "dt-bindings/input/input.h" > +#include "dt-bindings/pwm/pwm.h" > +#include "dt-bindings/usb/pd.h" > +#include "imx8mq.dtsi" > + > +/ { > + model = "Purism Librem 5"; > + compatible = "purism,librem5", "fsl,imx8mq"; > + > + backlight_dsi: backlight-dsi { > + compatible = "led-backlight"; > + leds = <&led_backlight>; > + brightness-levels = <255>; > + default-brightness-level = <100>; > + }; > + > + bm818_codec: sound-wwan-codec { > + compatible = "broadmobi,bm818", "option,gtm601"; > + #sound-dai-cells = <0>; > + }; Please sort the node names alpabetical. > + > + chosen { > + stdout-path = &uart1; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_keys>, <&pinctrl_hp>; > + > + hp-det { > + label = "HP_DET"; > + gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>; > + wakeup-source; > + linux,code = <KEY_HP>; Nit: I would add the wakeup-source behind the linux,code. > + }; > + > + vol-down { > + label = "VOL_DOWN"; > + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEDOWN>; > + }; > + > + vol-up { > + label = "VOL_UP"; > + gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + }; > + }; > + > + pwmleds { > + compatible = "pwm-leds"; > + > + blue { > + label = "phone:blue:front"; > + max-brightness = <248>; > + pwms = <&pwm2 0 50000>; > + }; > + > + green { > + label = "phone:green:front"; > + max-brightness = <248>; > + pwms = <&pwm4 0 50000>; > + }; > + > + red { > + label = "phone:red:front"; > + max-brightness = <248>; > + pwms = <&pwm3 0 50000>; > + }; > + }; > + > + pmic_osc: clock-pmic { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <32768>; > + clock-output-names = "pmic_osc"; > + }; Please sort nodes alphabetical. > + > + reg_audio_pwr_en: regulator-audio-pwr-en { > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_audiopwr>; > + regulator-name = "AUDIO_PWR_EN"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-always-on; Why should this regulator be always on? The wm8962.c driver can handle the regualtor enable/disable. > + }; > + > + reg_aud_1v8: regulator-audio-v1v8 { ^ regulator-audio-1v8? > + compatible = "regulator-fixed"; > + regulator-name = "aud_1v8"; Is it intended to use capitalized and no-capitalized regulator-name's? > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <®_audio_pwr_en>; > + }; Can we squash regulator-audio-pwr-en and regulator-audio-v1v8? > + > + reg_gnss: regulator-gnss { > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gnsspwr>; > + regulator-name = "GNSS"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio3 12 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_hub: regulator-hub { > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hub_pwr>; > + regulator-name = "HUB"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_lcd_1v8: regulator-lcd-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "lcd_1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_dsien>; > + vin-supply = <®_vdd_1v8>; > + enable-active-high; > + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; > + }; This regulator is never used. > + > + reg_lcd_3v4: regulator-lcd-3v4 { > + compatible = "regulator-fixed"; > + regulator-name = "lcd_3v4"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_dsibiasen>; > + vin-supply = <®_vsys_3v4>; > + enable-active-high; > + gpio = <&gpio1 20 GPIO_ACTIVE_HIGH>; > + }; > + > + reg_vdd_sen: regulator-vdd-sen { > + compatible = "regulator-fixed"; > + regulator-name = "vdd_sen"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + reg_vdd_3v3: regulator-vdd-3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "vdd_3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + reg_vdd_1v8: regulator-vdd-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "vdd_1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + reg_vsys_3v4: regulator-vsys-3v4 { > + compatible = "regulator-fixed"; > + regulator-name = "vsys_3v4"; > + regulator-min-microvolt = <3400000>; > + regulator-max-microvolt = <3400000>; > + regulator-always-on; > + }; > + > + reg_3v3_wifi: regulator-3v3-wifi { ^ reg_wifi_3v3: regulator-wifi-3v3? > + compatible = "regulator-fixed"; > + regulator-name = "3v3_wifi"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + sound { > + compatible = "simple-audio-card"; > + simple-audio-card,name = "wm8962"; > + simple-audio-card,format = "i2s"; > + simple-audio-card,widgets = > + "Headphone", "Headphone", > + "Microphone", "Headset Mic", > + "Microphone", "Digital Mic", > + "Speaker", "Speaker"; > + simple-audio-card,routing = > + "Headphone", "HPOUTL", > + "Headphone", "HPOUTR", > + "Speaker", "SPKOUTL", > + "Speaker", "SPKOUTR", > + "Headset Mic", "MICBIAS", > + "IN3R", "Headset Mic", > + "DMICDAT", "Digital Mic"; > + simple-audio-card,cpu { > + sound-dai = <&sai2>; > + }; > + simple-audio-card,codec { > + sound-dai = <&codec>; > + clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>; > + frame-master; > + bitclock-master; > + }; > + }; > + > + sound-wwan { > + compatible = "simple-audio-card"; > + simple-audio-card,name = "MODEM"; > + simple-audio-card,format = "i2s"; > + > + simple-audio-card,cpu { > + sound-dai = <&sai6>; > + frame-inversion; > + }; > + > + telephony_link_master: simple-audio-card,codec { ^ useless phandle? > + sound-dai = <&bm818_codec>; > + frame-master; > + bitclock-master; > + }; > + }; > + > + vibrator { > + compatible = "pwm-vibrator"; > + pwms = <&pwm1 0 1000000000 0>; > + pwm-names = "enable"; > + vcc-supply = <®_vdd_3v3>; > + }; > +}; > + > +&A53_0 { > + cpu-supply = <&buck2_reg>; > +}; > + > +&A53_1 { > + cpu-supply = <&buck2_reg>; > +}; > + > +&A53_2 { > + cpu-supply = <&buck2_reg>; > +}; > + > +&A53_3 { > + cpu-supply = <&buck2_reg>; > +}; > + > +&clk { > + assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>; > + assigned-clock-rates = <786432000>, <722534400>; > +}; Either I would bundle all clock settings here or within the sai nodes. > + > +&ddrc { > + operating-points-v2 = <&ddrc_opp_table>; > + > + ddrc_opp_table: ddrc-opp-table { > + compatible = "operating-points-v2"; > + > + opp-25M { > + opp-hz = /bits/ 64 <25000000>; > + }; > + opp-100M { > + opp-hz = /bits/ 64 <100000000>; > + }; > + opp-800M { > + opp-hz = /bits/ 64 <800000000>; > + }; > + }; > +}; > + > +&dphy { > + status = "okay"; > +}; > + > +&ecspi1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi1>; > + cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; Missmatch with the pinctrl_ecspi1? > + status = "okay"; Status is always the last property. > + #address-cells = <1>; > + #size-cells = <0>; > + > + nor_flash: flash@0 { > + compatible = "jedec,spi-nor"; > + spi-max-frequency = <1000000>; > + reg = <0>; > + }; > +}; > + > +&gpio1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pmic_5v>; > + > + pmic-5v { > + gpio-hog; > + gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; > + input; > + }; > +}; > + > +&iomuxc { > + pinctrl_audiopwr: audiopwrgrp { > + fsl,pins = < > + /* AUDIO_POWER_EN_3V3 */ > + MX8MQ_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x83 > + >; > + }; > + > + pinctrl_bl: blgrp { > + fsl,pins = < > + /* BACKLINGE_EN */ > + MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x83 > + >; > + }; > + > + pinctrl_charger_in: chargeringrp { > + fsl,pins = < > + /* CHRG_INT */ > + MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x80 > + /* CHG_STATUS_B */ > + MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0 0x80 > + >; > + }; > + > + pinctrl_dsibiasen: dsibiasengrp { > + fsl,pins = < > + /* DSI_BIAS_EN */ > + MX8MQ_IOMUXC_ENET_TD1_GPIO1_IO20 0x83 > + >; > + }; > + > + pinctrl_dsien: dsiengrp { > + fsl,pins = < > + /* DSI_EN_3V3 */ > + MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x83 > + >; > + }; > + > + pinctrl_ecspi1: spi1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x83 > + MX8MQ_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x83 > + MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19 > + MX8MQ_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x83 > + /* SPI_SS1 */ > + MX8MQ_IOMUXC_UART4_RXD_GPIO5_IO28 0x19 > + >; > + }; > + > + pinctrl_gauge: gaugegrp { > + fsl,pins = < > + /* BAT_LOW */ > + MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20 0x80 > + >; > + }; > + > + pinctrl_gnsspwr: gnsspwrgrp { > + fsl,pins = < > + /* GPS3V3_EN */ > + MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x83 > + >; > + }; > + > + pinctrl_haptic: hapticgrp { > + fsl,pins = < > + /* MOTO */ > + MX8MQ_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT 0x83 > + >; > + }; > + > + pinctrl_hp: hpgrp { > + fsl,pins = < > + /* HEADPHONE_DET_1V8 */ > + MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9 0x180 > + >; > + }; > + > + pinctrl_hub_pwr: hubpwrgrp { > + fsl,pins = < > + /* HUB_PWR_3V3_EN */ > + MX8MQ_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x83 > + >; > + }; > + > + pinctrl_i2c1: i2c1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000026 > + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000026 > + >; > + }; > + > + pinctrl_i2c2: i2c2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000026 > + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000026 > + >; > + }; > + > + pinctrl_i2c3: i2c3grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000026 > + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000026 > + >; > + }; > + > + pinctrl_i2c4: i2c4grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000026 > + MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000026 > + >; > + }; > + > + pinctrl_keys: keysgrp { > + fsl,pins = < > + /* 4G_WAKE */ > + MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x80 > + /* PWR_KEY */ > + MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x01C0 gpio3 5/15 are never used was this intended? > + /* VOL- */ > + MX8MQ_IOMUXC_ENET_MDIO_GPIO1_IO17 0x01C0 > + /* VOL+ */ > + MX8MQ_IOMUXC_ENET_MDC_GPIO1_IO16 0x01C0 > + >; > + }; > + > + pinctrl_led_b: ledbgrp { > + fsl,pins = < > + /* LED_B */ > + MX8MQ_IOMUXC_GPIO1_IO13_PWM2_OUT 0x06 > + >; > + }; > + > + pinctrl_led_g: ledggrp { > + fsl,pins = < > + /* LED_G */ > + MX8MQ_IOMUXC_SAI3_MCLK_PWM4_OUT 0x06 > + >; > + }; > + > + pinctrl_led_r: ledrgrp { > + fsl,pins = < > + /* LED_R */ > + MX8MQ_IOMUXC_SPDIF_TX_PWM3_OUT 0x06 > + >; > + }; > + > + pinctrl_mag: maggrp { > + fsl,pins = < > + /* INT_MAG */ > + MX8MQ_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x80 > + >; > + }; > + > + pinctrl_pmic: pmicgrp { > + fsl,pins = < > + /* PMIC_NINT */ > + MX8MQ_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x80 > + >; > + }; > + > + pinctrl_pmic_5v: pmic5vgrp { > + fsl,pins = < > + /* PMIC_5V */ > + MX8MQ_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x80 > + >; > + }; > + > + pinctrl_prox: proxgrp { > + fsl,pins = < > + /* INT_LIGHT */ > + MX8MQ_IOMUXC_NAND_DATA01_GPIO3_IO7 0x80 > + >; > + }; > + > + pinctrl_rtc: rtcgrp { > + fsl,pins = < > + /* RTC_INT */ > + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x80 > + >; > + }; > + > + pinctrl_sai2: sai2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6 > + MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6 > + MX8MQ_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6 > + MX8MQ_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0xd6 > + MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6 > + >; > + }; > + > + pinctrl_sai6: sai6grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SAI1_RXD5_SAI6_RX_DATA0 0xd6 > + MX8MQ_IOMUXC_SAI1_RXD6_SAI6_RX_SYNC 0xd6 > + MX8MQ_IOMUXC_SAI1_TXD4_SAI6_RX_BCLK 0xd6 > + MX8MQ_IOMUXC_SAI1_TXD5_SAI6_TX_DATA0 0xd6 > + >; > + }; > + > + pinctrl_tcpc: tcpcgrp { > + fsl,pins = < > + /* TCPC_INT */ > + MX8MQ_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x01C0 > + >; > + }; > + > + pinctrl_typec: typecgrp { > + fsl,pins = < > + /* TYPEC_MUX_EN */ > + MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x83 > + >; > + }; > + > + pinctrl_uart1: uart1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49 > + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49 > + >; > + }; > + > + pinctrl_uart2: uart2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49 > + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49 > + >; > + }; > + > + pinctrl_uart3: uart3grp { > + fsl,pins = < > + MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49 > + MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49 > + >; > + }; > + > + pinctrl_uart4: uart4grp { > + fsl,pins = < > + MX8MQ_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX 0x49 > + MX8MQ_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX 0x49 > + MX8MQ_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B 0x49 > + MX8MQ_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B 0x49 > + >; > + }; > + > + pinctrl_usdhc1: usdhc1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 > + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 > + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 > + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 > + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 > + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83 > + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 > + >; > + }; > + > + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { > + fsl,pins = < > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd > + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd > + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd > + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd > + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd > + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d > + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 > + >; > + }; > + > + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { > + fsl,pins = < > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf > + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf > + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf > + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf > + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf > + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f > + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 > + >; > + }; > + > + pinctrl_usdhc2: usdhc2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x80 > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83 > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3 > + MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1 > + >; > + }; > + > + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x80 > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd > + MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1 > + >; > + }; > + > + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x80 > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcf > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcf > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcf > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcf > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcf > + MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1 > + >; > + }; > + > + pinctrl_wdog: wdoggrp { > + fsl,pins = < > + /* nWDOG */ > + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x1f > + >; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <387000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + status = "okay"; > + > + typec_pd: usb-pd@3f { > + compatible = "ti,tps6598x"; > + reg = <0x3f>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_typec>, <&pinctrl_tcpc>; > + interrupt-parent = <&gpio1>; > + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; > + > + connector { > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + usb_con_hs: endpoint { > + remote-endpoint = <&typec_hs>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + usb_con_ss: endpoint { > + remote-endpoint = <&typec_ss>; > + }; > + }; > + }; > + }; > + }; > + > + pmic: pmic@4b { > + compatible = "rohm,bd71837"; > + reg = <0x4b>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pmic>; > + clocks = <&pmic_osc>; > + clock-names = "osc"; > + clock-output-names = "pmic_clk"; > + interrupt-parent = <&gpio1>; > + interrupts = <7 GPIO_ACTIVE_LOW>; > + interrupt-names = "irq"; > + rohm,reset-snvs-powered; > + > + regulators { > + buck1_reg: BUCK1 { > + regulator-name = "buck1"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <1300000>; > + regulator-ramp-delay = <1250>; > + rohm,dvs-run-voltage = <900000>; > + rohm,dvs-idle-voltage = <850000>; > + rohm,dvs-suspend-voltage = <800000>; > + regulator-always-on; > + }; > + > + buck2_reg: BUCK2 { > + regulator-name = "buck2"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <1300000>; > + regulator-ramp-delay = <1250>; > + rohm,dvs-run-voltage = <1000000>; > + rohm,dvs-idle-voltage = <900000>; > + regulator-always-on; > + }; > + > + buck3_reg: BUCK3 { > + regulator-name = "buck3"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <1300000>; > + rohm,dvs-run-voltage = <900000>; > + regulator-always-on; > + }; > + > + buck4_reg: BUCK4 { > + regulator-name = "buck4"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <1300000>; > + rohm,dvs-run-voltage = <1000000>; > + }; > + > + buck5_reg: BUCK5 { > + regulator-name = "buck5"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + }; > + > + buck6_reg: BUCK6 { > + regulator-name = "buck6"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + buck7_reg: BUCK7 { > + regulator-name = "buck7"; > + regulator-min-microvolt = <1605000>; > + regulator-max-microvolt = <1995000>; > + regulator-always-on; > + }; > + > + buck8_reg: BUCK8 { > + regulator-name = "buck8"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1400000>; > + regulator-always-on; > + }; > + > + ldo1_reg: LDO1 { > + regulator-name = "ldo1"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3300000>; > + /* leave on for snvs power button */ > + regulator-always-on; > + }; > + > + ldo2_reg: LDO2 { > + regulator-name = "ldo2"; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <900000>; > + /* leave on for snvs power button */ > + regulator-always-on; > + }; > + > + ldo3_reg: LDO3 { > + regulator-name = "ldo3"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + ldo4_reg: LDO4 { > + regulator-name = "ldo4"; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + ldo5_reg: LDO5 { > + /* VDD_PHY_0V9 - MIPI and HDMI domains */ > + regulator-name = "ldo5"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + ldo6_reg: LDO6 { > + /* VDD_PHY_0V9 - MIPI, HDMI and USB domains */ > + regulator-name = "ldo6"; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + ldo7_reg: LDO7 { > + /* VDD_PHY_3V3 - USB domain */ > + regulator-name = "ldo7"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; Out of curiosity, why did you marked all regulators as regulator-always-on? I thought the librem5 is a smartphone. > + }; > + }; > + > + rtc@68 { > + compatible = "microcrystal,rv4162"; > + reg = <0x68>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_rtc>; > + interrupt-parent = <&gpio1>; > + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; > + }; > +}; > + > +&i2c2 { > + clock-frequency = <387000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + status = "okay"; > + > + magnetometer@1e { > + compatible = "st,lsm9ds1-magn"; > + reg = <0x1e>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_mag>; > + interrupt-parent = <&gpio3>; > + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; > + vdd-supply = <®_vdd_sen>; > + vddio-supply = <®_vdd_1v8>; > + }; > + > + regulator@3e { > + compatible = "tps65132"; > + reg = <0x3e>; > + reg_lcd_avdd: outp { > + regulator-name = "lcd_avdd"; > + vin-supply = <®_lcd_3v4>; > + }; > + > + reg_lcd_avee: outn { > + regulator-name = "lcd_avee"; > + vin-supply = <®_lcd_3v4>; > + }; both phandles are not used. > + }; > + > + flash@53 { > + compatible = "lm3560"; > + reg = <0x53>; > + #address-cells = <1>; > + #size-cells = <0>; > + flash@0 { > + reg = <0x0>; > + flash-timeout-us = <150000>; > + flash-max-microamp = <320000>; > + led-max-microamp = <60000>; > + label = "lm3560:flash"; > + }; > + > + torch@1 { > + reg = <0x1>; > + led-max-microamp = <10000>; > + label = "lm3560:torch"; > + }; > + > + }; > + > + prox@60 { > + compatible = "vishay,vcnl4040"; > + reg = <0x60>; > + pinctrl-0 = <&pinctrl_prox>; > + interrupt-parent = <&gpio3>; > + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; > + }; > + > + accel-gyro@6a { > + compatible = "st,lsm9ds1-imu"; > + reg = <0x6a>; > + vdd-supply = <®_vdd_sen>; > + vddio-supply = <®_vdd_1v8>; > + mount-matrix = "1", "0", "0", > + "0", "1", "0", > + "0", "0", "-1"; > + }; > +}; > + > +&i2c3 { > + clock-frequency = <387000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + status = "okay"; > + > + codec: wm8962@1a { Please use generic names. > + compatible = "wlf,wm8962"; > + reg = <0x1a>; // 0x4a is the test address > + clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>; > + assigned-clocks = <&clk IMX8MQ_CLK_SAI2>; > + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; > + assigned-clock-rates = <24576000>; > + #sound-dai-cells = <0>; > + mic-cfg = <0x200>; > + DCVDD-supply = <®_aud_1v8>; > + DBVDD-supply = <®_aud_1v8>; > + AVDD-supply = <®_aud_1v8>; > + CPVDD-supply = <®_aud_1v8>; > + MICVDD-supply = <®_aud_1v8>; > + PLLVDD-supply = <®_aud_1v8>; > + SPKVDD1-supply = <®_vsys_3v4>; > + SPKVDD2-supply = <®_vsys_3v4>; > + gpio-cfg = < > + 0x0000 /* n/c */ > + 0x0001 /* gpio2, 1: default */ > + 0x0013 /* gpio3, 2: dmicclk */ > + 0x0000 /* n/c, 3: default */ > + 0x8014 /* gpio5, 4: dmic_dat */ > + 0x0000 /* gpio6, 5: default */ > + >; > + status = "okay"; status can be dropped > + }; > + > + backlight@36 { > + compatible = "ti,lm36922"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_bl>; > + reg = <0x36>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + enable-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; > + vled-supply = <®_vsys_3v4>; > + ti,ovp-microvolt = <25000000>; > + > + led_backlight: led@0 { > + reg = <0>; > + label = "white:backlight_cluster"; > + linux,default-trigger = "backlight"; > + led-max-microamp = <20000>; > + }; > + }; > + > + touchscreen@38 { > + compatible = "edt,edt-ft5506"; > + reg = <0x38>; > + interrupt-parent = <&gpio1>; > + interrupts = <27 IRQ_TYPE_EDGE_FALLING>; You need to mux the irq gpio. > + irq-gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>; irq-gpios is not supported by the driver. We only have a wake/reset-gpio. > + touchscreen-size-x = <720>; > + touchscreen-size-y = <1440>; > + }; > +}; > + > +&i2c4 { > + clock-frequency = <387000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c4>; > + status = "okay"; > + > + bat: fuel-gauge@36 { > + compatible = "maxim,max17055"; > + interrupt-parent = <&gpio3>; > + interrupts = <20 IRQ_TYPE_LEVEL_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gauge>; > + reg = <0x36>; Please check that "reg" is always the 2nd property after the "compatible". > + maxim,over-heat-temp = <700>; > + maxim,over-volt = <4500>; > + maxim,rsns-microohm = <5000>; > + }; > + > + charger@6a { /* bq25895 */ > + compatible = "ti,bq25890"; The compatible should be "ti,bq25895" if it is a bq25895. So we can drop the comment too. > + reg = <0x6a>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_charger_in>; > + interrupt-parent = <&gpio3>; > + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; > + phys = <&usb3_phy0>; > + ti,battery-regulation-voltage = <4192000>; /* 4.192V */ > + ti,charge-current = <1600000>; /* 1.6A */ > + ti,termination-current = <66000>; /* 66mA */ > + ti,precharge-current = <130000>; /* 130mA */ > + ti,minimum-sys-voltage = <3700000>; /* 3.7V */ > + ti,boost-voltage = <5000000>; /* 5V */ > + ti,boost-max-current = <50000>; /* 50mA */ > + ti,use-vinmin-threshold = <1>; /* enable VINDPM */ > + ti,vinmin-threshold = <3900000>; /* 3.9V */ I would only mention the units within a comment because comments like this begin to divergence after you fix something. Regards, Marco > + monitored-battery = <&bat>; > + }; > +}; > + > +&pgc_gpu { > + power-supply = <&buck3_reg>; > +}; > + > +&pgc_mipi { > + power-supply = <&ldo5_reg>; > +}; > + > +&pgc_vpu { > + power-supply = <&buck4_reg>; > +}; > + > +&pwm1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_haptic>; > + status = "okay"; > +}; > + > +&pwm2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_led_b>; > + status = "okay"; > +}; > + > +&pwm3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_led_g>; > + status = "okay"; > +}; > + > +&pwm4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_led_r>; > + status = "okay"; > +}; > + > +&sai2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sai2>; > + assigned-clocks = <&clk IMX8MQ_CLK_SAI2>; > + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; > + assigned-clock-rates = <24576000>; > + status = "okay"; > +}; > + > +&sai6 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sai6>; > + assigned-clocks = <&clk IMX8MQ_CLK_SAI6>; > + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; > + assigned-clock-rates = <24576000>; > + fsl,sai-synchronous-rx; > + status = "okay"; > +}; > + > +&snvs_pwrkey { > + status = "okay"; > +}; > + > +&snvs_rtc { > + status = "disabled"; > +}; > + > +&uart1 { /* console */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + status = "okay"; > +}; > + > +&uart2 { /* TPS - GPS - DEBUG */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2>; > + status = "okay"; > + > + gnss { > + compatible = "globaltop,pa6h"; > + vcc-supply = <®_gnss>; > + current-speed = <9600>; > + }; > +}; > + > +&uart3 { /* SMC */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + status = "okay"; > +}; > + > +&uart4 { /* BT */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart4>; > + uart-has-rtscts; > + status = "okay"; > +}; > + > +&usb3_phy0 { > + status = "okay"; > +}; > + > +&usb3_phy1 { > + vbus-supply = <®_hub>; > + status = "okay"; > +}; > + > +&usb_dwc3_0 { > + #address-cells = <1>; > + #size-cells = <0>; > + dr_mode = "otg"; > + snps,dis_u3_susphy_quirk; > + status = "okay"; > + > + port@0 { > + reg = <0>; > + > + typec_hs: endpoint { > + remote-endpoint = <&usb_con_hs>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + typec_ss: endpoint { > + remote-endpoint = <&usb_con_ss>; > + }; > + }; > +}; > + > +&usb_dwc3_1 { > + dr_mode = "host"; > + snps,dis_u2_susphy_quirk; > + snps,dis_u3_susphy_quirk; > + status = "okay"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; > + bus-width = <8>; > + vmmc-supply = <®_vdd_3v3>; > + power-supply = <®_vdd_1v8>; > + non-removable; > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc2>; > + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; > + bus-width = <4>; > + vmmc-supply = <®_3v3_wifi>; > + broken-cd; > + disable-wp; > + cap-sdio-irq; > + keep-power-in-suspend; > + wakeup-source; > + status = "okay"; > +}; > + > +&wdog1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_wdog>; > + fsl,ext-reset-output; > + status = "okay"; > +}; > -- > 2.20.1 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi! > From: "Angus Ainslie (Purism)" <angus@akkea.ca> > > Add a devicetree description for the Librem 5 phone. The early batches > that have been sold are supported as well as the mass-produced device > available later this year, see https://puri.sm/products/librem-5/ > > This boots to a working console with working WWAN modem, wifi usdhc, > IMU sensor device, proximity sensor, haptic motor, gpio keys, GNSS and LEDs. > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> > Signed-off-by: Guido Günther <agx@sigxcpu.org> > + blue { > + label = "phone:blue:front"; > + label = "phone:green:front"; > + label = "phone:red:front"; Droid 4 uses "status-led:{red,green,blue}". Could this use same naming? > + label = "lm3560:flash"; > + label = "lm3560:torch"; This is one LED, right? I'm pretty sure we don't want lm3560 in the name... "main-camera:flash" would be better. Even better would be something that's already in use. > + label = "white:backlight_cluster"; Make this ":backlight", please. Again, we want something that's already used. Best regards, Pavel
Hi! Plus, do we need calibration matrix for magnetometer? Best regards, Pavel
On 29.05.20 20:07, Pavel Machek wrote: > Hi! > > Plus, do we need calibration matrix for magnetometer? I guess so. It's not a calibration matrix, it's the mount matrix that tells you how the chip is placed on the PCB relative to a "natural" orientation, see https://github.com/torvalds/linux/blob/master/Documentation/ABI/testing/sysfs-bus-iio#L1638 > > Best regards, > Pavel >
Hi, On Fri, May 29, 2020 at 06:28:50PM +0200, Pavel Machek wrote: > Hi! > > > From: "Angus Ainslie (Purism)" <angus@akkea.ca> > > > > Add a devicetree description for the Librem 5 phone. The early batches > > that have been sold are supported as well as the mass-produced device > > available later this year, see https://puri.sm/products/librem-5/ > > > > This boots to a working console with working WWAN modem, wifi usdhc, > > IMU sensor device, proximity sensor, haptic motor, gpio keys, GNSS and LEDs. > > > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > > Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> > > Signed-off-by: Guido Günther <agx@sigxcpu.org> > > > > + blue { > > + label = "phone:blue:front"; > > + label = "phone:green:front"; > > + label = "phone:red:front"; > > Droid 4 uses "status-led:{red,green,blue}". Could this use same > naming? Looking at leds-class.rst we don't have a useful devicename so should that just be omitted and s.th. like label = "blue:status"; label = "green:status"; label = "red:status"; be used instead. If we want to map to current usage label = "blue:status"; label = "green:boot"; label = "red:charging"; would be even closer but since that is bound to change just going with "status" would make sense. Cheers, -- Guido > > > + label = "lm3560:flash"; > > + label = "lm3560:torch"; > > This is one LED, right? I'm pretty sure we don't want lm3560 in the > name... "main-camera:flash" would be better. Even better would be > something that's already in use. > > > + label = "white:backlight_cluster"; > > Make this ":backlight", please. Again, we want something that's > already used. > > Best regards, > Pavel > -- > (english) http://www.livejournal.com/~pavelmachek > (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
Hi Marco, On 27.05.20 11:35, Marco Felsch wrote: > Hi Martin, > > On 20-05-14 17:57, Martin Kepplinger wrote: >> From: "Angus Ainslie (Purism)" <angus@akkea.ca> >> >> Add a devicetree description for the Librem 5 phone. The early batches >> that have been sold are supported as well as the mass-produced device >> available later this year, see https://puri.sm/products/librem-5/ >> >> This boots to a working console with working WWAN modem, wifi usdhc, >> IMU sensor device, proximity sensor, haptic motor, gpio keys, GNSS and LEDs. >> >> Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> >> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> >> Signed-off-by: Guido Günther <agx@sigxcpu.org> >> --- >> arch/arm64/boot/dts/freescale/Makefile | 1 + >> .../boot/dts/freescale/imx8mq-librem5.dts | 1174 +++++++++++++++++ >> 2 files changed, 1175 insertions(+) >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5.dts >> >> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile >> index cd38d04da5a7..342579121f98 100644 >> --- a/arch/arm64/boot/dts/freescale/Makefile >> +++ b/arch/arm64/boot/dts/freescale/Makefile >> @@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb >> dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb >> dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb >> dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb >> +dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5.dtb >> dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb >> dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb >> dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb >> diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dts >> new file mode 100644 >> index 000000000000..95c105b4c120 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dts >> @@ -0,0 +1,1174 @@ >> +// SPDX-License-Identifier: GPL-2.0+ >> +/* >> + * Copyright 2018-2020 Purism SPC >> + */ >> + >> +/dts-v1/; >> + >> +#include "dt-bindings/input/input.h" >> +#include "dt-bindings/pwm/pwm.h" >> +#include "dt-bindings/usb/pd.h" >> +#include "imx8mq.dtsi" >> + >> +/ { >> + model = "Purism Librem 5"; >> + compatible = "purism,librem5", "fsl,imx8mq"; >> + >> + backlight_dsi: backlight-dsi { >> + compatible = "led-backlight"; >> + leds = <&led_backlight>; >> + brightness-levels = <255>; >> + default-brightness-level = <100>; >> + }; >> + >> + bm818_codec: sound-wwan-codec { >> + compatible = "broadmobi,bm818", "option,gtm601"; >> + #sound-dai-cells = <0>; >> + }; > > Please sort the node names alpabetical. > >> + >> + chosen { >> + stdout-path = &uart1; >> + }; >> + >> + gpio-keys { >> + compatible = "gpio-keys"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_keys>, <&pinctrl_hp>; >> + >> + hp-det { >> + label = "HP_DET"; >> + gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>; >> + wakeup-source; >> + linux,code = <KEY_HP>; > > Nit: I would add the wakeup-source behind the linux,code. > >> + }; >> + >> + vol-down { >> + label = "VOL_DOWN"; >> + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; >> + linux,code = <KEY_VOLUMEDOWN>; >> + }; >> + >> + vol-up { >> + label = "VOL_UP"; >> + gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; >> + linux,code = <KEY_VOLUMEUP>; >> + }; >> + }; >> + >> + pwmleds { >> + compatible = "pwm-leds"; >> + >> + blue { >> + label = "phone:blue:front"; >> + max-brightness = <248>; >> + pwms = <&pwm2 0 50000>; >> + }; >> + >> + green { >> + label = "phone:green:front"; >> + max-brightness = <248>; >> + pwms = <&pwm4 0 50000>; >> + }; >> + >> + red { >> + label = "phone:red:front"; >> + max-brightness = <248>; >> + pwms = <&pwm3 0 50000>; >> + }; >> + }; >> + >> + pmic_osc: clock-pmic { >> + compatible = "fixed-clock"; >> + #clock-cells = <0>; >> + clock-frequency = <32768>; >> + clock-output-names = "pmic_osc"; >> + }; > > Please sort nodes alphabetical. > >> + >> + reg_audio_pwr_en: regulator-audio-pwr-en { >> + compatible = "regulator-fixed"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_audiopwr>; >> + regulator-name = "AUDIO_PWR_EN"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; >> + enable-active-high; >> + regulator-always-on; > > Why should this regulator be always on? The wm8962.c driver can handle > the regualtor enable/disable. It can indeed be handled by the driver here. We keep it always on because of issues with the display stack that are not yet part of this description. > >> + }; >> + >> + reg_aud_1v8: regulator-audio-v1v8 { > ^ > regulator-audio-1v8? > >> + compatible = "regulator-fixed"; >> + regulator-name = "aud_1v8"; > > Is it intended to use capitalized and no-capitalized regulator-name's? > >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + vin-supply = <®_audio_pwr_en>; >> + }; > > Can we squash regulator-audio-pwr-en and regulator-audio-v1v8? I think we can. > >> + >> + reg_gnss: regulator-gnss { >> + compatible = "regulator-fixed"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_gnsspwr>; >> + regulator-name = "GNSS"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + gpio = <&gpio3 12 GPIO_ACTIVE_HIGH>; >> + enable-active-high; >> + }; >> + >> + reg_hub: regulator-hub { >> + compatible = "regulator-fixed"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_hub_pwr>; >> + regulator-name = "HUB"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; >> + enable-active-high; >> + }; >> + >> + reg_lcd_1v8: regulator-lcd-1v8 { >> + compatible = "regulator-fixed"; >> + regulator-name = "lcd_1v8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_dsien>; >> + vin-supply = <®_vdd_1v8>; >> + enable-active-high; >> + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; >> + }; > > This regulator is never used. > >> + >> + reg_lcd_3v4: regulator-lcd-3v4 { >> + compatible = "regulator-fixed"; >> + regulator-name = "lcd_3v4"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_dsibiasen>; >> + vin-supply = <®_vsys_3v4>; >> + enable-active-high; >> + gpio = <&gpio1 20 GPIO_ACTIVE_HIGH>; >> + }; >> + >> + reg_vdd_sen: regulator-vdd-sen { >> + compatible = "regulator-fixed"; >> + regulator-name = "vdd_sen"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + }; >> + >> + reg_vdd_3v3: regulator-vdd-3v3 { >> + compatible = "regulator-fixed"; >> + regulator-name = "vdd_3v3"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + }; >> + >> + reg_vdd_1v8: regulator-vdd-1v8 { >> + compatible = "regulator-fixed"; >> + regulator-name = "vdd_1v8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + }; >> + >> + reg_vsys_3v4: regulator-vsys-3v4 { >> + compatible = "regulator-fixed"; >> + regulator-name = "vsys_3v4"; >> + regulator-min-microvolt = <3400000>; >> + regulator-max-microvolt = <3400000>; >> + regulator-always-on; >> + }; >> + >> + reg_3v3_wifi: regulator-3v3-wifi { > ^ > reg_wifi_3v3: regulator-wifi-3v3? > >> + compatible = "regulator-fixed"; >> + regulator-name = "3v3_wifi"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + }; >> + >> + sound { >> + compatible = "simple-audio-card"; >> + simple-audio-card,name = "wm8962"; >> + simple-audio-card,format = "i2s"; >> + simple-audio-card,widgets = >> + "Headphone", "Headphone", >> + "Microphone", "Headset Mic", >> + "Microphone", "Digital Mic", >> + "Speaker", "Speaker"; >> + simple-audio-card,routing = >> + "Headphone", "HPOUTL", >> + "Headphone", "HPOUTR", >> + "Speaker", "SPKOUTL", >> + "Speaker", "SPKOUTR", >> + "Headset Mic", "MICBIAS", >> + "IN3R", "Headset Mic", >> + "DMICDAT", "Digital Mic"; >> + simple-audio-card,cpu { >> + sound-dai = <&sai2>; >> + }; >> + simple-audio-card,codec { >> + sound-dai = <&codec>; >> + clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>; >> + frame-master; >> + bitclock-master; >> + }; >> + }; >> + >> + sound-wwan { >> + compatible = "simple-audio-card"; >> + simple-audio-card,name = "MODEM"; >> + simple-audio-card,format = "i2s"; >> + >> + simple-audio-card,cpu { >> + sound-dai = <&sai6>; >> + frame-inversion; >> + }; >> + >> + telephony_link_master: simple-audio-card,codec { > ^ > useless phandle? >> + sound-dai = <&bm818_codec>; >> + frame-master; >> + bitclock-master; >> + }; >> + }; >> + >> + vibrator { >> + compatible = "pwm-vibrator"; >> + pwms = <&pwm1 0 1000000000 0>; >> + pwm-names = "enable"; >> + vcc-supply = <®_vdd_3v3>; >> + }; >> +}; >> + >> +&A53_0 { >> + cpu-supply = <&buck2_reg>; >> +}; >> + >> +&A53_1 { >> + cpu-supply = <&buck2_reg>; >> +}; >> + >> +&A53_2 { >> + cpu-supply = <&buck2_reg>; >> +}; >> + >> +&A53_3 { >> + cpu-supply = <&buck2_reg>; >> +}; >> + >> +&clk { >> + assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>; >> + assigned-clock-rates = <786432000>, <722534400>; >> +}; > > Either I would bundle all clock settings here or within the sai nodes. You're right, I'll try to move them. > >> + >> +&ddrc { >> + operating-points-v2 = <&ddrc_opp_table>; >> + >> + ddrc_opp_table: ddrc-opp-table { >> + compatible = "operating-points-v2"; >> + >> + opp-25M { >> + opp-hz = /bits/ 64 <25000000>; >> + }; >> + opp-100M { >> + opp-hz = /bits/ 64 <100000000>; >> + }; >> + opp-800M { >> + opp-hz = /bits/ 64 <800000000>; >> + }; >> + }; >> +}; >> + >> +&dphy { >> + status = "okay"; >> +}; >> + >> +&ecspi1 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_ecspi1>; >> + cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; > > Missmatch with the pinctrl_ecspi1? > >> + status = "okay"; > > Status is always the last property. > >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + nor_flash: flash@0 { >> + compatible = "jedec,spi-nor"; >> + spi-max-frequency = <1000000>; >> + reg = <0>; >> + }; >> +}; >> + >> +&gpio1 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_pmic_5v>; >> + >> + pmic-5v { >> + gpio-hog; >> + gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; >> + input; >> + }; >> +}; >> + >> +&iomuxc { >> + pinctrl_audiopwr: audiopwrgrp { >> + fsl,pins = < >> + /* AUDIO_POWER_EN_3V3 */ >> + MX8MQ_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x83 >> + >; >> + }; >> + >> + pinctrl_bl: blgrp { >> + fsl,pins = < >> + /* BACKLINGE_EN */ >> + MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x83 >> + >; >> + }; >> + >> + pinctrl_charger_in: chargeringrp { >> + fsl,pins = < >> + /* CHRG_INT */ >> + MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x80 >> + /* CHG_STATUS_B */ >> + MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0 0x80 >> + >; >> + }; >> + >> + pinctrl_dsibiasen: dsibiasengrp { >> + fsl,pins = < >> + /* DSI_BIAS_EN */ >> + MX8MQ_IOMUXC_ENET_TD1_GPIO1_IO20 0x83 >> + >; >> + }; >> + >> + pinctrl_dsien: dsiengrp { >> + fsl,pins = < >> + /* DSI_EN_3V3 */ >> + MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x83 >> + >; >> + }; >> + >> + pinctrl_ecspi1: spi1grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x83 >> + MX8MQ_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x83 >> + MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19 >> + MX8MQ_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x83 >> + /* SPI_SS1 */ >> + MX8MQ_IOMUXC_UART4_RXD_GPIO5_IO28 0x19 >> + >; >> + }; >> + >> + pinctrl_gauge: gaugegrp { >> + fsl,pins = < >> + /* BAT_LOW */ >> + MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20 0x80 >> + >; >> + }; >> + >> + pinctrl_gnsspwr: gnsspwrgrp { >> + fsl,pins = < >> + /* GPS3V3_EN */ >> + MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x83 >> + >; >> + }; >> + >> + pinctrl_haptic: hapticgrp { >> + fsl,pins = < >> + /* MOTO */ >> + MX8MQ_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT 0x83 >> + >; >> + }; >> + >> + pinctrl_hp: hpgrp { >> + fsl,pins = < >> + /* HEADPHONE_DET_1V8 */ >> + MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9 0x180 >> + >; >> + }; >> + >> + pinctrl_hub_pwr: hubpwrgrp { >> + fsl,pins = < >> + /* HUB_PWR_3V3_EN */ >> + MX8MQ_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x83 >> + >; >> + }; >> + >> + pinctrl_i2c1: i2c1grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000026 >> + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000026 >> + >; >> + }; >> + >> + pinctrl_i2c2: i2c2grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000026 >> + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000026 >> + >; >> + }; >> + >> + pinctrl_i2c3: i2c3grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000026 >> + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000026 >> + >; >> + }; >> + >> + pinctrl_i2c4: i2c4grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000026 >> + MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000026 >> + >; >> + }; >> + >> + pinctrl_keys: keysgrp { >> + fsl,pins = < >> + /* 4G_WAKE */ >> + MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x80 >> + /* PWR_KEY */ >> + MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x01C0 > > gpio3 5/15 are never used was this intended? > >> + /* VOL- */ >> + MX8MQ_IOMUXC_ENET_MDIO_GPIO1_IO17 0x01C0 >> + /* VOL+ */ >> + MX8MQ_IOMUXC_ENET_MDC_GPIO1_IO16 0x01C0 >> + >; >> + }; >> + >> + pinctrl_led_b: ledbgrp { >> + fsl,pins = < >> + /* LED_B */ >> + MX8MQ_IOMUXC_GPIO1_IO13_PWM2_OUT 0x06 >> + >; >> + }; >> + >> + pinctrl_led_g: ledggrp { >> + fsl,pins = < >> + /* LED_G */ >> + MX8MQ_IOMUXC_SAI3_MCLK_PWM4_OUT 0x06 >> + >; >> + }; >> + >> + pinctrl_led_r: ledrgrp { >> + fsl,pins = < >> + /* LED_R */ >> + MX8MQ_IOMUXC_SPDIF_TX_PWM3_OUT 0x06 >> + >; >> + }; >> + >> + pinctrl_mag: maggrp { >> + fsl,pins = < >> + /* INT_MAG */ >> + MX8MQ_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x80 >> + >; >> + }; >> + >> + pinctrl_pmic: pmicgrp { >> + fsl,pins = < >> + /* PMIC_NINT */ >> + MX8MQ_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x80 >> + >; >> + }; >> + >> + pinctrl_pmic_5v: pmic5vgrp { >> + fsl,pins = < >> + /* PMIC_5V */ >> + MX8MQ_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x80 >> + >; >> + }; >> + >> + pinctrl_prox: proxgrp { >> + fsl,pins = < >> + /* INT_LIGHT */ >> + MX8MQ_IOMUXC_NAND_DATA01_GPIO3_IO7 0x80 >> + >; >> + }; >> + >> + pinctrl_rtc: rtcgrp { >> + fsl,pins = < >> + /* RTC_INT */ >> + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x80 >> + >; >> + }; >> + >> + pinctrl_sai2: sai2grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6 >> + MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6 >> + MX8MQ_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6 >> + MX8MQ_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0xd6 >> + MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6 >> + >; >> + }; >> + >> + pinctrl_sai6: sai6grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_SAI1_RXD5_SAI6_RX_DATA0 0xd6 >> + MX8MQ_IOMUXC_SAI1_RXD6_SAI6_RX_SYNC 0xd6 >> + MX8MQ_IOMUXC_SAI1_TXD4_SAI6_RX_BCLK 0xd6 >> + MX8MQ_IOMUXC_SAI1_TXD5_SAI6_TX_DATA0 0xd6 >> + >; >> + }; >> + >> + pinctrl_tcpc: tcpcgrp { >> + fsl,pins = < >> + /* TCPC_INT */ >> + MX8MQ_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x01C0 >> + >; >> + }; >> + >> + pinctrl_typec: typecgrp { >> + fsl,pins = < >> + /* TYPEC_MUX_EN */ >> + MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x83 >> + >; >> + }; >> + >> + pinctrl_uart1: uart1grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49 >> + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49 >> + >; >> + }; >> + >> + pinctrl_uart2: uart2grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49 >> + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49 >> + >; >> + }; >> + >> + pinctrl_uart3: uart3grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49 >> + MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49 >> + >; >> + }; >> + >> + pinctrl_uart4: uart4grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX 0x49 >> + MX8MQ_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX 0x49 >> + MX8MQ_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B 0x49 >> + MX8MQ_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B 0x49 >> + >; >> + }; >> + >> + pinctrl_usdhc1: usdhc1grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 >> + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 >> + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 >> + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 >> + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 >> + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 >> + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 >> + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 >> + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 >> + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 >> + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83 >> + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 >> + >; >> + }; >> + >> + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { >> + fsl,pins = < >> + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d >> + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd >> + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd >> + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd >> + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd >> + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd >> + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd >> + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd >> + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd >> + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd >> + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d >> + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 >> + >; >> + }; >> + >> + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { >> + fsl,pins = < >> + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f >> + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf >> + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf >> + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf >> + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf >> + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf >> + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf >> + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf >> + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf >> + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf >> + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f >> + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 >> + >; >> + }; >> + >> + pinctrl_usdhc2: usdhc2grp { >> + fsl,pins = < >> + MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x80 >> + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83 >> + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 >> + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 >> + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 >> + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 >> + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3 >> + MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1 >> + >; >> + }; >> + >> + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { >> + fsl,pins = < >> + MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x80 >> + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d >> + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd >> + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd >> + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd >> + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd >> + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd >> + MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1 >> + >; >> + }; >> + >> + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { >> + fsl,pins = < >> + MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x80 >> + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f >> + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcf >> + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcf >> + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcf >> + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcf >> + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcf >> + MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1 >> + >; >> + }; >> + >> + pinctrl_wdog: wdoggrp { >> + fsl,pins = < >> + /* nWDOG */ >> + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x1f >> + >; >> + }; >> +}; >> + >> +&i2c1 { >> + clock-frequency = <387000>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c1>; >> + status = "okay"; >> + >> + typec_pd: usb-pd@3f { >> + compatible = "ti,tps6598x"; >> + reg = <0x3f>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_typec>, <&pinctrl_tcpc>; >> + interrupt-parent = <&gpio1>; >> + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; >> + >> + connector { >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port@0 { >> + reg = <0>; >> + >> + usb_con_hs: endpoint { >> + remote-endpoint = <&typec_hs>; >> + }; >> + }; >> + >> + port@1 { >> + reg = <1>; >> + >> + usb_con_ss: endpoint { >> + remote-endpoint = <&typec_ss>; >> + }; >> + }; >> + }; >> + }; >> + }; >> + >> + pmic: pmic@4b { >> + compatible = "rohm,bd71837"; >> + reg = <0x4b>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_pmic>; >> + clocks = <&pmic_osc>; >> + clock-names = "osc"; >> + clock-output-names = "pmic_clk"; >> + interrupt-parent = <&gpio1>; >> + interrupts = <7 GPIO_ACTIVE_LOW>; >> + interrupt-names = "irq"; >> + rohm,reset-snvs-powered; >> + >> + regulators { >> + buck1_reg: BUCK1 { >> + regulator-name = "buck1"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <1300000>; >> + regulator-ramp-delay = <1250>; >> + rohm,dvs-run-voltage = <900000>; >> + rohm,dvs-idle-voltage = <850000>; >> + rohm,dvs-suspend-voltage = <800000>; >> + regulator-always-on; >> + }; >> + >> + buck2_reg: BUCK2 { >> + regulator-name = "buck2"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <1300000>; >> + regulator-ramp-delay = <1250>; >> + rohm,dvs-run-voltage = <1000000>; >> + rohm,dvs-idle-voltage = <900000>; >> + regulator-always-on; >> + }; >> + >> + buck3_reg: BUCK3 { >> + regulator-name = "buck3"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <1300000>; >> + rohm,dvs-run-voltage = <900000>; >> + regulator-always-on; >> + }; >> + >> + buck4_reg: BUCK4 { >> + regulator-name = "buck4"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <1300000>; >> + rohm,dvs-run-voltage = <1000000>; >> + }; >> + >> + buck5_reg: BUCK5 { >> + regulator-name = "buck5"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <1350000>; >> + regulator-always-on; >> + }; >> + >> + buck6_reg: BUCK6 { >> + regulator-name = "buck6"; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-always-on; >> + }; >> + >> + buck7_reg: BUCK7 { >> + regulator-name = "buck7"; >> + regulator-min-microvolt = <1605000>; >> + regulator-max-microvolt = <1995000>; >> + regulator-always-on; >> + }; >> + >> + buck8_reg: BUCK8 { >> + regulator-name = "buck8"; >> + regulator-min-microvolt = <800000>; >> + regulator-max-microvolt = <1400000>; >> + regulator-always-on; >> + }; >> + >> + ldo1_reg: LDO1 { >> + regulator-name = "ldo1"; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3300000>; >> + /* leave on for snvs power button */ >> + regulator-always-on; >> + }; >> + >> + ldo2_reg: LDO2 { >> + regulator-name = "ldo2"; >> + regulator-min-microvolt = <900000>; >> + regulator-max-microvolt = <900000>; >> + /* leave on for snvs power button */ >> + regulator-always-on; >> + }; >> + >> + ldo3_reg: LDO3 { >> + regulator-name = "ldo3"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-always-on; >> + }; >> + >> + ldo4_reg: LDO4 { >> + regulator-name = "ldo4"; >> + regulator-min-microvolt = <900000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-always-on; >> + }; >> + >> + ldo5_reg: LDO5 { >> + /* VDD_PHY_0V9 - MIPI and HDMI domains */ >> + regulator-name = "ldo5"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-always-on; >> + }; >> + >> + ldo6_reg: LDO6 { >> + /* VDD_PHY_0V9 - MIPI, HDMI and USB domains */ >> + regulator-name = "ldo6"; >> + regulator-min-microvolt = <900000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-always-on; >> + }; >> + >> + ldo7_reg: LDO7 { >> + /* VDD_PHY_3V3 - USB domain */ >> + regulator-name = "ldo7"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-always-on; >> + }; > > Out of curiosity, why did you marked all regulators as > regulator-always-on? I thought the librem5 is a smartphone. It is. But we just currently see an unstable system in case we allow turning most of them off. We do for the VPU, and should (afaik already) be able to do so for the GPU. After more work in the drivers the mipi regulator(s) should be able to be turned off. So we'll look at more and more of these over time. > >> + }; >> + }; >> + >> + rtc@68 { >> + compatible = "microcrystal,rv4162"; >> + reg = <0x68>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_rtc>; >> + interrupt-parent = <&gpio1>; >> + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; >> + }; >> +}; >> + >> +&i2c2 { >> + clock-frequency = <387000>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c2>; >> + status = "okay"; >> + >> + magnetometer@1e { >> + compatible = "st,lsm9ds1-magn"; >> + reg = <0x1e>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_mag>; >> + interrupt-parent = <&gpio3>; >> + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; >> + vdd-supply = <®_vdd_sen>; >> + vddio-supply = <®_vdd_1v8>; >> + }; >> + >> + regulator@3e { >> + compatible = "tps65132"; >> + reg = <0x3e>; >> + reg_lcd_avdd: outp { >> + regulator-name = "lcd_avdd"; >> + vin-supply = <®_lcd_3v4>; >> + }; >> + >> + reg_lcd_avee: outn { >> + regulator-name = "lcd_avee"; >> + vin-supply = <®_lcd_3v4>; >> + }; > both phandles are not used. >> + }; >> + >> + flash@53 { >> + compatible = "lm3560"; >> + reg = <0x53>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + flash@0 { >> + reg = <0x0>; >> + flash-timeout-us = <150000>; >> + flash-max-microamp = <320000>; >> + led-max-microamp = <60000>; >> + label = "lm3560:flash"; >> + }; >> + >> + torch@1 { >> + reg = <0x1>; >> + led-max-microamp = <10000>; >> + label = "lm3560:torch"; >> + }; >> + >> + }; >> + >> + prox@60 { >> + compatible = "vishay,vcnl4040"; >> + reg = <0x60>; >> + pinctrl-0 = <&pinctrl_prox>; >> + interrupt-parent = <&gpio3>; >> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; >> + }; >> + >> + accel-gyro@6a { >> + compatible = "st,lsm9ds1-imu"; >> + reg = <0x6a>; >> + vdd-supply = <®_vdd_sen>; >> + vddio-supply = <®_vdd_1v8>; >> + mount-matrix = "1", "0", "0", >> + "0", "1", "0", >> + "0", "0", "-1"; >> + }; >> +}; >> + >> +&i2c3 { >> + clock-frequency = <387000>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c3>; >> + status = "okay"; >> + >> + codec: wm8962@1a { > > Please use generic names. > >> + compatible = "wlf,wm8962"; >> + reg = <0x1a>; // 0x4a is the test address >> + clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>; >> + assigned-clocks = <&clk IMX8MQ_CLK_SAI2>; >> + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; >> + assigned-clock-rates = <24576000>; >> + #sound-dai-cells = <0>; >> + mic-cfg = <0x200>; >> + DCVDD-supply = <®_aud_1v8>; >> + DBVDD-supply = <®_aud_1v8>; >> + AVDD-supply = <®_aud_1v8>; >> + CPVDD-supply = <®_aud_1v8>; >> + MICVDD-supply = <®_aud_1v8>; >> + PLLVDD-supply = <®_aud_1v8>; >> + SPKVDD1-supply = <®_vsys_3v4>; >> + SPKVDD2-supply = <®_vsys_3v4>; >> + gpio-cfg = < >> + 0x0000 /* n/c */ >> + 0x0001 /* gpio2, 1: default */ >> + 0x0013 /* gpio3, 2: dmicclk */ >> + 0x0000 /* n/c, 3: default */ >> + 0x8014 /* gpio5, 4: dmic_dat */ >> + 0x0000 /* gpio6, 5: default */ >> + >; >> + status = "okay"; > > status can be dropped > >> + }; >> + >> + backlight@36 { >> + compatible = "ti,lm36922"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_bl>; >> + reg = <0x36>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + enable-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; >> + vled-supply = <®_vsys_3v4>; >> + ti,ovp-microvolt = <25000000>; >> + >> + led_backlight: led@0 { >> + reg = <0>; >> + label = "white:backlight_cluster"; >> + linux,default-trigger = "backlight"; >> + led-max-microamp = <20000>; >> + }; >> + }; >> + >> + touchscreen@38 { >> + compatible = "edt,edt-ft5506"; >> + reg = <0x38>; >> + interrupt-parent = <&gpio1>; >> + interrupts = <27 IRQ_TYPE_EDGE_FALLING>; > > You need to mux the irq gpio. > >> + irq-gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>; > > irq-gpios is not supported by the driver. We only have a > wake/reset-gpio. > >> + touchscreen-size-x = <720>; >> + touchscreen-size-y = <1440>; >> + }; >> +}; >> + >> +&i2c4 { >> + clock-frequency = <387000>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c4>; >> + status = "okay"; >> + >> + bat: fuel-gauge@36 { >> + compatible = "maxim,max17055"; >> + interrupt-parent = <&gpio3>; >> + interrupts = <20 IRQ_TYPE_LEVEL_LOW>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_gauge>; >> + reg = <0x36>; > > Please check that "reg" is always the 2nd property after the > "compatible". > >> + maxim,over-heat-temp = <700>; >> + maxim,over-volt = <4500>; >> + maxim,rsns-microohm = <5000>; >> + }; >> + >> + charger@6a { /* bq25895 */ >> + compatible = "ti,bq25890"; > > The compatible should be "ti,bq25895" if it is a bq25895. So we can drop > the comment too. > >> + reg = <0x6a>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_charger_in>; >> + interrupt-parent = <&gpio3>; >> + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; >> + phys = <&usb3_phy0>; >> + ti,battery-regulation-voltage = <4192000>; /* 4.192V */ >> + ti,charge-current = <1600000>; /* 1.6A */ >> + ti,termination-current = <66000>; /* 66mA */ >> + ti,precharge-current = <130000>; /* 130mA */ >> + ti,minimum-sys-voltage = <3700000>; /* 3.7V */ >> + ti,boost-voltage = <5000000>; /* 5V */ >> + ti,boost-max-current = <50000>; /* 50mA */ >> + ti,use-vinmin-threshold = <1>; /* enable VINDPM */ >> + ti,vinmin-threshold = <3900000>; /* 3.9V */ > > I would only mention the units within a comment because comments like > this begin to divergence after you fix something. > > Regards, > Marco > Basically I try to follow all your suggestions that I haven't commented here, too. thank you very much for this in-depth review. That helps a lot and I try to put together a second revision soon. martin
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index cd38d04da5a7..342579121f98 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dts new file mode 100644 index 000000000000..95c105b4c120 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dts @@ -0,0 +1,1174 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2020 Purism SPC + */ + +/dts-v1/; + +#include "dt-bindings/input/input.h" +#include "dt-bindings/pwm/pwm.h" +#include "dt-bindings/usb/pd.h" +#include "imx8mq.dtsi" + +/ { + model = "Purism Librem 5"; + compatible = "purism,librem5", "fsl,imx8mq"; + + backlight_dsi: backlight-dsi { + compatible = "led-backlight"; + leds = <&led_backlight>; + brightness-levels = <255>; + default-brightness-level = <100>; + }; + + bm818_codec: sound-wwan-codec { + compatible = "broadmobi,bm818", "option,gtm601"; + #sound-dai-cells = <0>; + }; + + chosen { + stdout-path = &uart1; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_keys>, <&pinctrl_hp>; + + hp-det { + label = "HP_DET"; + gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>; + wakeup-source; + linux,code = <KEY_HP>; + }; + + vol-down { + label = "VOL_DOWN"; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + }; + + vol-up { + label = "VOL_UP"; + gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + pwmleds { + compatible = "pwm-leds"; + + blue { + label = "phone:blue:front"; + max-brightness = <248>; + pwms = <&pwm2 0 50000>; + }; + + green { + label = "phone:green:front"; + max-brightness = <248>; + pwms = <&pwm4 0 50000>; + }; + + red { + label = "phone:red:front"; + max-brightness = <248>; + pwms = <&pwm3 0 50000>; + }; + }; + + pmic_osc: clock-pmic { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "pmic_osc"; + }; + + reg_audio_pwr_en: regulator-audio-pwr-en { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audiopwr>; + regulator-name = "AUDIO_PWR_EN"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_aud_1v8: regulator-audio-v1v8 { + compatible = "regulator-fixed"; + regulator-name = "aud_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <®_audio_pwr_en>; + }; + + reg_gnss: regulator-gnss { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gnsspwr>; + regulator-name = "GNSS"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_hub: regulator-hub { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hub_pwr>; + regulator-name = "HUB"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_lcd_1v8: regulator-lcd-1v8 { + compatible = "regulator-fixed"; + regulator-name = "lcd_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dsien>; + vin-supply = <®_vdd_1v8>; + enable-active-high; + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; + }; + + reg_lcd_3v4: regulator-lcd-3v4 { + compatible = "regulator-fixed"; + regulator-name = "lcd_3v4"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dsibiasen>; + vin-supply = <®_vsys_3v4>; + enable-active-high; + gpio = <&gpio1 20 GPIO_ACTIVE_HIGH>; + }; + + reg_vdd_sen: regulator-vdd-sen { + compatible = "regulator-fixed"; + regulator-name = "vdd_sen"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_vdd_3v3: regulator-vdd-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vdd_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_vdd_1v8: regulator-vdd-1v8 { + compatible = "regulator-fixed"; + regulator-name = "vdd_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_vsys_3v4: regulator-vsys-3v4 { + compatible = "regulator-fixed"; + regulator-name = "vsys_3v4"; + regulator-min-microvolt = <3400000>; + regulator-max-microvolt = <3400000>; + regulator-always-on; + }; + + reg_3v3_wifi: regulator-3v3-wifi { + compatible = "regulator-fixed"; + regulator-name = "3v3_wifi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "wm8962"; + simple-audio-card,format = "i2s"; + simple-audio-card,widgets = + "Headphone", "Headphone", + "Microphone", "Headset Mic", + "Microphone", "Digital Mic", + "Speaker", "Speaker"; + simple-audio-card,routing = + "Headphone", "HPOUTL", + "Headphone", "HPOUTR", + "Speaker", "SPKOUTL", + "Speaker", "SPKOUTR", + "Headset Mic", "MICBIAS", + "IN3R", "Headset Mic", + "DMICDAT", "Digital Mic"; + simple-audio-card,cpu { + sound-dai = <&sai2>; + }; + simple-audio-card,codec { + sound-dai = <&codec>; + clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>; + frame-master; + bitclock-master; + }; + }; + + sound-wwan { + compatible = "simple-audio-card"; + simple-audio-card,name = "MODEM"; + simple-audio-card,format = "i2s"; + + simple-audio-card,cpu { + sound-dai = <&sai6>; + frame-inversion; + }; + + telephony_link_master: simple-audio-card,codec { + sound-dai = <&bm818_codec>; + frame-master; + bitclock-master; + }; + }; + + vibrator { + compatible = "pwm-vibrator"; + pwms = <&pwm1 0 1000000000 0>; + pwm-names = "enable"; + vcc-supply = <®_vdd_3v3>; + }; +}; + +&A53_0 { + cpu-supply = <&buck2_reg>; +}; + +&A53_1 { + cpu-supply = <&buck2_reg>; +}; + +&A53_2 { + cpu-supply = <&buck2_reg>; +}; + +&A53_3 { + cpu-supply = <&buck2_reg>; +}; + +&clk { + assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>; + assigned-clock-rates = <786432000>, <722534400>; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: ddrc-opp-table { + compatible = "operating-points-v2"; + + opp-25M { + opp-hz = /bits/ 64 <25000000>; + }; + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; + opp-800M { + opp-hz = /bits/ 64 <800000000>; + }; + }; +}; + +&dphy { + status = "okay"; +}; + +&ecspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + nor_flash: flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <1000000>; + reg = <0>; + }; +}; + +&gpio1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic_5v>; + + pmic-5v { + gpio-hog; + gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; + input; + }; +}; + +&iomuxc { + pinctrl_audiopwr: audiopwrgrp { + fsl,pins = < + /* AUDIO_POWER_EN_3V3 */ + MX8MQ_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x83 + >; + }; + + pinctrl_bl: blgrp { + fsl,pins = < + /* BACKLINGE_EN */ + MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x83 + >; + }; + + pinctrl_charger_in: chargeringrp { + fsl,pins = < + /* CHRG_INT */ + MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x80 + /* CHG_STATUS_B */ + MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0 0x80 + >; + }; + + pinctrl_dsibiasen: dsibiasengrp { + fsl,pins = < + /* DSI_BIAS_EN */ + MX8MQ_IOMUXC_ENET_TD1_GPIO1_IO20 0x83 + >; + }; + + pinctrl_dsien: dsiengrp { + fsl,pins = < + /* DSI_EN_3V3 */ + MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x83 + >; + }; + + pinctrl_ecspi1: spi1grp { + fsl,pins = < + MX8MQ_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x83 + MX8MQ_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x83 + MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19 + MX8MQ_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x83 + /* SPI_SS1 */ + MX8MQ_IOMUXC_UART4_RXD_GPIO5_IO28 0x19 + >; + }; + + pinctrl_gauge: gaugegrp { + fsl,pins = < + /* BAT_LOW */ + MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20 0x80 + >; + }; + + pinctrl_gnsspwr: gnsspwrgrp { + fsl,pins = < + /* GPS3V3_EN */ + MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x83 + >; + }; + + pinctrl_haptic: hapticgrp { + fsl,pins = < + /* MOTO */ + MX8MQ_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT 0x83 + >; + }; + + pinctrl_hp: hpgrp { + fsl,pins = < + /* HEADPHONE_DET_1V8 */ + MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9 0x180 + >; + }; + + pinctrl_hub_pwr: hubpwrgrp { + fsl,pins = < + /* HUB_PWR_3V3_EN */ + MX8MQ_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x83 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000026 + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000026 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000026 + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000026 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000026 + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000026 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000026 + MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000026 + >; + }; + + pinctrl_keys: keysgrp { + fsl,pins = < + /* 4G_WAKE */ + MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x80 + /* PWR_KEY */ + MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x01C0 + /* VOL- */ + MX8MQ_IOMUXC_ENET_MDIO_GPIO1_IO17 0x01C0 + /* VOL+ */ + MX8MQ_IOMUXC_ENET_MDC_GPIO1_IO16 0x01C0 + >; + }; + + pinctrl_led_b: ledbgrp { + fsl,pins = < + /* LED_B */ + MX8MQ_IOMUXC_GPIO1_IO13_PWM2_OUT 0x06 + >; + }; + + pinctrl_led_g: ledggrp { + fsl,pins = < + /* LED_G */ + MX8MQ_IOMUXC_SAI3_MCLK_PWM4_OUT 0x06 + >; + }; + + pinctrl_led_r: ledrgrp { + fsl,pins = < + /* LED_R */ + MX8MQ_IOMUXC_SPDIF_TX_PWM3_OUT 0x06 + >; + }; + + pinctrl_mag: maggrp { + fsl,pins = < + /* INT_MAG */ + MX8MQ_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x80 + >; + }; + + pinctrl_pmic: pmicgrp { + fsl,pins = < + /* PMIC_NINT */ + MX8MQ_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x80 + >; + }; + + pinctrl_pmic_5v: pmic5vgrp { + fsl,pins = < + /* PMIC_5V */ + MX8MQ_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x80 + >; + }; + + pinctrl_prox: proxgrp { + fsl,pins = < + /* INT_LIGHT */ + MX8MQ_IOMUXC_NAND_DATA01_GPIO3_IO7 0x80 + >; + }; + + pinctrl_rtc: rtcgrp { + fsl,pins = < + /* RTC_INT */ + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x80 + >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6 + MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6 + MX8MQ_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6 + MX8MQ_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0xd6 + MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6 + >; + }; + + pinctrl_sai6: sai6grp { + fsl,pins = < + MX8MQ_IOMUXC_SAI1_RXD5_SAI6_RX_DATA0 0xd6 + MX8MQ_IOMUXC_SAI1_RXD6_SAI6_RX_SYNC 0xd6 + MX8MQ_IOMUXC_SAI1_TXD4_SAI6_RX_BCLK 0xd6 + MX8MQ_IOMUXC_SAI1_TXD5_SAI6_TX_DATA0 0xd6 + >; + }; + + pinctrl_tcpc: tcpcgrp { + fsl,pins = < + /* TCPC_INT */ + MX8MQ_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x01C0 + >; + }; + + pinctrl_typec: typecgrp { + fsl,pins = < + /* TYPEC_MUX_EN */ + MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x83 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49 + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49 + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49 + MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MQ_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX 0x49 + MX8MQ_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX 0x49 + MX8MQ_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B 0x49 + MX8MQ_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B 0x49 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83 + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x80 + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83 + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3 + MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x80 + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd + MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x80 + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcf + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcf + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcf + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcf + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcf + MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + /* nWDOG */ + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x1f + >; + }; +}; + +&i2c1 { + clock-frequency = <387000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + typec_pd: usb-pd@3f { + compatible = "ti,tps6598x"; + reg = <0x3f>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_typec>, <&pinctrl_tcpc>; + interrupt-parent = <&gpio1>; + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; + + connector { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + usb_con_hs: endpoint { + remote-endpoint = <&typec_hs>; + }; + }; + + port@1 { + reg = <1>; + + usb_con_ss: endpoint { + remote-endpoint = <&typec_ss>; + }; + }; + }; + }; + }; + + pmic: pmic@4b { + compatible = "rohm,bd71837"; + reg = <0x4b>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + clocks = <&pmic_osc>; + clock-names = "osc"; + clock-output-names = "pmic_clk"; + interrupt-parent = <&gpio1>; + interrupts = <7 GPIO_ACTIVE_LOW>; + interrupt-names = "irq"; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <900000>; + rohm,dvs-idle-voltage = <850000>; + rohm,dvs-suspend-voltage = <800000>; + regulator-always-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; + regulator-always-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + rohm,dvs-run-voltage = <900000>; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "buck4"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + rohm,dvs-run-voltage = <1000000>; + }; + + buck5_reg: BUCK5 { + regulator-name = "buck5"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "buck6"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + buck7_reg: BUCK7 { + regulator-name = "buck7"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-always-on; + }; + + buck8_reg: BUCK8 { + regulator-name = "buck8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + /* leave on for snvs power button */ + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + /* leave on for snvs power button */ + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + /* VDD_PHY_0V9 - MIPI and HDMI domains */ + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + /* VDD_PHY_0V9 - MIPI, HDMI and USB domains */ + regulator-name = "ldo6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo7_reg: LDO7 { + /* VDD_PHY_3V3 - USB domain */ + regulator-name = "ldo7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; + + rtc@68 { + compatible = "microcrystal,rv4162"; + reg = <0x68>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&i2c2 { + clock-frequency = <387000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + magnetometer@1e { + compatible = "st,lsm9ds1-magn"; + reg = <0x1e>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mag>; + interrupt-parent = <&gpio3>; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + vdd-supply = <®_vdd_sen>; + vddio-supply = <®_vdd_1v8>; + }; + + regulator@3e { + compatible = "tps65132"; + reg = <0x3e>; + reg_lcd_avdd: outp { + regulator-name = "lcd_avdd"; + vin-supply = <®_lcd_3v4>; + }; + + reg_lcd_avee: outn { + regulator-name = "lcd_avee"; + vin-supply = <®_lcd_3v4>; + }; + }; + + flash@53 { + compatible = "lm3560"; + reg = <0x53>; + #address-cells = <1>; + #size-cells = <0>; + flash@0 { + reg = <0x0>; + flash-timeout-us = <150000>; + flash-max-microamp = <320000>; + led-max-microamp = <60000>; + label = "lm3560:flash"; + }; + + torch@1 { + reg = <0x1>; + led-max-microamp = <10000>; + label = "lm3560:torch"; + }; + + }; + + prox@60 { + compatible = "vishay,vcnl4040"; + reg = <0x60>; + pinctrl-0 = <&pinctrl_prox>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + }; + + accel-gyro@6a { + compatible = "st,lsm9ds1-imu"; + reg = <0x6a>; + vdd-supply = <®_vdd_sen>; + vddio-supply = <®_vdd_1v8>; + mount-matrix = "1", "0", "0", + "0", "1", "0", + "0", "0", "-1"; + }; +}; + +&i2c3 { + clock-frequency = <387000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + codec: wm8962@1a { + compatible = "wlf,wm8962"; + reg = <0x1a>; // 0x4a is the test address + clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>; + assigned-clocks = <&clk IMX8MQ_CLK_SAI2>; + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + #sound-dai-cells = <0>; + mic-cfg = <0x200>; + DCVDD-supply = <®_aud_1v8>; + DBVDD-supply = <®_aud_1v8>; + AVDD-supply = <®_aud_1v8>; + CPVDD-supply = <®_aud_1v8>; + MICVDD-supply = <®_aud_1v8>; + PLLVDD-supply = <®_aud_1v8>; + SPKVDD1-supply = <®_vsys_3v4>; + SPKVDD2-supply = <®_vsys_3v4>; + gpio-cfg = < + 0x0000 /* n/c */ + 0x0001 /* gpio2, 1: default */ + 0x0013 /* gpio3, 2: dmicclk */ + 0x0000 /* n/c, 3: default */ + 0x8014 /* gpio5, 4: dmic_dat */ + 0x0000 /* gpio6, 5: default */ + >; + status = "okay"; + }; + + backlight@36 { + compatible = "ti,lm36922"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_bl>; + reg = <0x36>; + #address-cells = <1>; + #size-cells = <0>; + + enable-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; + vled-supply = <®_vsys_3v4>; + ti,ovp-microvolt = <25000000>; + + led_backlight: led@0 { + reg = <0>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + led-max-microamp = <20000>; + }; + }; + + touchscreen@38 { + compatible = "edt,edt-ft5506"; + reg = <0x38>; + interrupt-parent = <&gpio1>; + interrupts = <27 IRQ_TYPE_EDGE_FALLING>; + irq-gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>; + touchscreen-size-x = <720>; + touchscreen-size-y = <1440>; + }; +}; + +&i2c4 { + clock-frequency = <387000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + bat: fuel-gauge@36 { + compatible = "maxim,max17055"; + interrupt-parent = <&gpio3>; + interrupts = <20 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gauge>; + reg = <0x36>; + maxim,over-heat-temp = <700>; + maxim,over-volt = <4500>; + maxim,rsns-microohm = <5000>; + }; + + charger@6a { /* bq25895 */ + compatible = "ti,bq25890"; + reg = <0x6a>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_in>; + interrupt-parent = <&gpio3>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + phys = <&usb3_phy0>; + ti,battery-regulation-voltage = <4192000>; /* 4.192V */ + ti,charge-current = <1600000>; /* 1.6A */ + ti,termination-current = <66000>; /* 66mA */ + ti,precharge-current = <130000>; /* 130mA */ + ti,minimum-sys-voltage = <3700000>; /* 3.7V */ + ti,boost-voltage = <5000000>; /* 5V */ + ti,boost-max-current = <50000>; /* 50mA */ + ti,use-vinmin-threshold = <1>; /* enable VINDPM */ + ti,vinmin-threshold = <3900000>; /* 3.9V */ + monitored-battery = <&bat>; + }; +}; + +&pgc_gpu { + power-supply = <&buck3_reg>; +}; + +&pgc_mipi { + power-supply = <&ldo5_reg>; +}; + +&pgc_vpu { + power-supply = <&buck4_reg>; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_haptic>; + status = "okay"; +}; + +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led_b>; + status = "okay"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led_g>; + status = "okay"; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led_r>; + status = "okay"; +}; + +&sai2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; + assigned-clocks = <&clk IMX8MQ_CLK_SAI2>; + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + +&sai6 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai6>; + assigned-clocks = <&clk IMX8MQ_CLK_SAI6>; + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + fsl,sai-synchronous-rx; + status = "okay"; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&snvs_rtc { + status = "disabled"; +}; + +&uart1 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { /* TPS - GPS - DEBUG */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; + + gnss { + compatible = "globaltop,pa6h"; + vcc-supply = <®_gnss>; + current-speed = <9600>; + }; +}; + +&uart3 { /* SMC */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart4 { /* BT */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + uart-has-rtscts; + status = "okay"; +}; + +&usb3_phy0 { + status = "okay"; +}; + +&usb3_phy1 { + vbus-supply = <®_hub>; + status = "okay"; +}; + +&usb_dwc3_0 { + #address-cells = <1>; + #size-cells = <0>; + dr_mode = "otg"; + snps,dis_u3_susphy_quirk; + status = "okay"; + + port@0 { + reg = <0>; + + typec_hs: endpoint { + remote-endpoint = <&usb_con_hs>; + }; + }; + + port@1 { + reg = <1>; + + typec_ss: endpoint { + remote-endpoint = <&usb_con_ss>; + }; + }; +}; + +&usb_dwc3_1 { + dr_mode = "host"; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <8>; + vmmc-supply = <®_vdd_3v3>; + power-supply = <®_vdd_1v8>; + non-removable; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + bus-width = <4>; + vmmc-supply = <®_3v3_wifi>; + broken-cd; + disable-wp; + cap-sdio-irq; + keep-power-in-suspend; + wakeup-source; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +};