| Message ID | 20200604085441.103087-4-kbastian@mail.uni-paderborn.de (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | tests/tcg: Add TriCore tests | expand |
Bastian Koppelmann <kbastian@mail.uni-paderborn.de> writes: > when trying to run successful short tests from the Makefile timeout would no > terminate. Rather it would wait until the time runs out. Excerpt from the > manpage: Which tests hang without this change? > > --foreground > when not running timeout directly from a shell prompt, > allow COMMAND to read from the TTY and get TTY signals; in this mode, chil‐ > dren of COMMAND will not be timed out > > Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> > --- > tests/tcg/Makefile.target | 5 +++-- > 1 file changed, 3 insertions(+), 2 deletions(-) > > diff --git a/tests/tcg/Makefile.target b/tests/tcg/Makefile.target > index b3cff3cad1..423caffa56 100644 > --- a/tests/tcg/Makefile.target > +++ b/tests/tcg/Makefile.target > @@ -40,9 +40,10 @@ quiet-command = $(if $(V),$1,$(if $(2),@printf " %-7s %s\n" $2 $3 && $1, @$1)) > > # $1 = test name, $2 = cmd, $3 = desc > ifdef CONFIG_USER_ONLY > -run-test = $(call quiet-command, timeout $(TIMEOUT) $2 > $1.out,"TEST",$3) > +run-test = $(call quiet-command, timeout --foreground $(TIMEOUT) $2 > $1.out \ > + "TEST",$3) This breaks make check-tcg due to a dropped , > else > -run-test = $(call quiet-command, timeout $(TIMEOUT) $2,"TEST",$3) > +run-test = $(call quiet-command, timeout --foreground $(TIMEOUT) $2,"TEST",$3) > endif > > # $1 = test name, $2 = reference
On Tue, Jun 16, 2020 at 05:22:42PM +0100, Alex Bennée wrote: > > Bastian Koppelmann <kbastian@mail.uni-paderborn.de> writes: > > > when trying to run successful short tests from the Makefile timeout would no > > terminate. Rather it would wait until the time runs out. Excerpt from the > > manpage: > > Which tests hang without this change? The TriCore tests ;). > > > > > --foreground > > when not running timeout directly from a shell prompt, > > allow COMMAND to read from the TTY and get TTY signals; in this mode, chil‐ > > dren of COMMAND will not be timed out > > > > Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> > > --- > > tests/tcg/Makefile.target | 5 +++-- > > 1 file changed, 3 insertions(+), 2 deletions(-) > > > > diff --git a/tests/tcg/Makefile.target b/tests/tcg/Makefile.target > > index b3cff3cad1..423caffa56 100644 > > --- a/tests/tcg/Makefile.target > > +++ b/tests/tcg/Makefile.target > > @@ -40,9 +40,10 @@ quiet-command = $(if $(V),$1,$(if $(2),@printf " %-7s %s\n" $2 $3 && $1, @$1)) > > > > # $1 = test name, $2 = cmd, $3 = desc > > ifdef CONFIG_USER_ONLY > > -run-test = $(call quiet-command, timeout $(TIMEOUT) $2 > $1.out,"TEST",$3) > > +run-test = $(call quiet-command, timeout --foreground $(TIMEOUT) $2 > $1.out \ > > + "TEST",$3) > > This breaks make check-tcg due to a dropped , Whoops Cheers, Bastian
Bastian Koppelmann <kbastian@mail.uni-paderborn.de> writes: > On Tue, Jun 16, 2020 at 05:22:42PM +0100, Alex Bennée wrote: >> >> Bastian Koppelmann <kbastian@mail.uni-paderborn.de> writes: >> >> > when trying to run successful short tests from the Makefile timeout would no >> > terminate. Rather it would wait until the time runs out. Excerpt from the >> > manpage: >> >> Which tests hang without this change? > > The TriCore tests ;). Hmm I wonder why? All the other tests work so is this a function of output from the test? The softmmu tests for example usually redirect their output via a chardev device. Tests which require actual input from the user are skipped (the semiconsole test is MANUAL only). > >> >> > >> > --foreground >> > when not running timeout directly from a shell prompt, >> > allow COMMAND to read from the TTY and get TTY signals; in this mode, chil‐ >> > dren of COMMAND will not be timed out >> > >> > Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> >> > --- >> > tests/tcg/Makefile.target | 5 +++-- >> > 1 file changed, 3 insertions(+), 2 deletions(-) >> > >> > diff --git a/tests/tcg/Makefile.target b/tests/tcg/Makefile.target >> > index b3cff3cad1..423caffa56 100644 >> > --- a/tests/tcg/Makefile.target >> > +++ b/tests/tcg/Makefile.target >> > @@ -40,9 +40,10 @@ quiet-command = $(if $(V),$1,$(if $(2),@printf " %-7s %s\n" $2 $3 && $1, @$1)) >> > >> > # $1 = test name, $2 = cmd, $3 = desc >> > ifdef CONFIG_USER_ONLY >> > -run-test = $(call quiet-command, timeout $(TIMEOUT) $2 > $1.out,"TEST",$3) >> > +run-test = $(call quiet-command, timeout --foreground $(TIMEOUT) $2 > $1.out \ >> > + "TEST",$3) >> >> This breaks make check-tcg due to a dropped , > > Whoops > > Cheers, > Bastian
Hi Alex, On Wed, Jun 17, 2020 at 10:59:22AM +0100, Alex Bennée wrote: > > Bastian Koppelmann <kbastian@mail.uni-paderborn.de> writes: > > > On Tue, Jun 16, 2020 at 05:22:42PM +0100, Alex Bennée wrote: > >> > >> Bastian Koppelmann <kbastian@mail.uni-paderborn.de> writes: > >> > >> > when trying to run successful short tests from the Makefile timeout would no > >> > terminate. Rather it would wait until the time runs out. Excerpt from the > >> > manpage: > >> > >> Which tests hang without this change? > > > > The TriCore tests ;). > > Hmm I wonder why? All the other tests work so is this a function of > output from the test? The softmmu tests for example usually redirect > their output via a chardev device. Tests which require actual input from > the user are skipped (the semiconsole test is MANUAL only). I was wondering as well. If you run the test command without --foreground on a shell, it works. If you run it from make, it times out. Maybe this is just on my end. I usually run bleeding edge software on my developing machines. I have timeout 8.32 here. Cheers, Bastian
diff --git a/tests/tcg/Makefile.target b/tests/tcg/Makefile.target index b3cff3cad1..423caffa56 100644 --- a/tests/tcg/Makefile.target +++ b/tests/tcg/Makefile.target @@ -40,9 +40,10 @@ quiet-command = $(if $(V),$1,$(if $(2),@printf " %-7s %s\n" $2 $3 && $1, @$1)) # $1 = test name, $2 = cmd, $3 = desc ifdef CONFIG_USER_ONLY -run-test = $(call quiet-command, timeout $(TIMEOUT) $2 > $1.out,"TEST",$3) +run-test = $(call quiet-command, timeout --foreground $(TIMEOUT) $2 > $1.out \ + "TEST",$3) else -run-test = $(call quiet-command, timeout $(TIMEOUT) $2,"TEST",$3) +run-test = $(call quiet-command, timeout --foreground $(TIMEOUT) $2,"TEST",$3) endif # $1 = test name, $2 = reference
when trying to run successful short tests from the Makefile timeout would no terminate. Rather it would wait until the time runs out. Excerpt from the manpage: --foreground when not running timeout directly from a shell prompt, allow COMMAND to read from the TTY and get TTY signals; in this mode, chil‐ dren of COMMAND will not be timed out Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> --- tests/tcg/Makefile.target | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)