[v9,0/5] mainline Protonic boards

Message

Oleksij Rempel July 1, 2020, 1:03 p.m. UTC

changes v9:
- rebase against kernel v5.8-rc3
- prti6q: set index to default-brightness-level
- prti6q: remove regulator-always-on
- prti6q: rename mux_ssi1 and mux_pins3 to mux-ssi1, mux-pins3
- prti6q: move can1 node out of dtsi and fix alphabetical order
- prti6q: fix reg value for rgmii_phy
- prti6q: fix pinctrl_can2 and pinctrl_can1
- vt7: fix fsl,mode
- vt7: rename mux_ssi1 and mux_pins3 to mux-ssi1, mux-pins3
- vt7: remove regulator-always-on
- wd2: remove pm-ignore-notify, it is not implemented and documented
- wd2: remove duplicate non-removable

changes v8:
- resend

changes v7:
- VT7: reorder node alphabetically
- VT7: rename "reg_12v_bl: regulator-bl-12v" to "reg_bl_12v0: regulator-bl-12v0"
- VT7: remove panel and TS nodes. This drivers are currently not
  mainline.
- prti6q.dtsi: move reg_1v8 to prti6q.dts
- prti6q.dtsi: remove pinctrl from the can1 node. It is done on almost
  every board file.

changes v6:
- move fsl.yaml changes to separate patch
- remove partitions, they are provided by the bootloader
- update flash compatible
- rename can3 to can
- fix fsl,mode
- fix interrupt in the wlan node on PRTI6Q

changes v5:
- PRTI6Q: remove status from the pwm-backlight node
- drop the vendor-prefixes patch, it is already taken by Rob
- add Reviewed-by: Rob Herring <[e-mail]>

changes v4:
- VT7: fix typo

changes v3:
- move compatible to the start of node
- move status to the end
- use generic names in compatible
- refactor dts/dtsi
- use alphabet order for pinctrl and phandels
- remove unused or currently not supported nodes

changes v2:
- squash PRTI6Q patches

Oleksij Rempel (5):
  dt-bindings: arm: fsl: add different Protonic boards
  ARM: dts: add Protonic PRTI6Q board
  ARM: dts: add Protonic WD2 board
  ARM: dts: add Protonic VT7 board
  ARM: dts: add Protonic RVT board

 .../devicetree/bindings/arm/fsl.yaml          |   4 +
 arch/arm/boot/dts/Makefile                    |   4 +
 arch/arm/boot/dts/imx6dl-prtrvt.dts           | 184 ++++++
 arch/arm/boot/dts/imx6dl-prtvt7.dts           | 410 +++++++++++++
 arch/arm/boot/dts/imx6q-prti6q.dts            | 542 ++++++++++++++++++
 arch/arm/boot/dts/imx6q-prtwd2.dts            | 188 ++++++
 arch/arm/boot/dts/imx6qdl-prti6q.dtsi         | 163 ++++++
 7 files changed, 1496 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
 create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
 create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
 create mode 100644 arch/arm/boot/dts/imx6q-prtwd2.dts
 create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi

Comments

Shawn Guo July 13, 2020, 3:25 a.m. UTC | #1

On Wed, Jul 01, 2020 at 03:03:25PM +0200, Oleksij Rempel wrote:
> Oleksij Rempel (5):
>   dt-bindings: arm: fsl: add different Protonic boards
>   ARM: dts: add Protonic PRTI6Q board
>   ARM: dts: add Protonic WD2 board
>   ARM: dts: add Protonic VT7 board
>   ARM: dts: add Protonic RVT board

Applied all, thanks.