| Message ID | 20200824084712.2526079-3-vkoul@kernel.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/3] dt-bindings: dmaengine: Document qcom,gpi dma binding | expand |
Hi Vinod, On 24/08/2020 11.47, Vinod Koul wrote: > Some complex dmaengine controllers have capability to program the > peripheral device, so pass on the peripheral configuration as part of > dma_slave_config > > Signed-off-by: Vinod Koul <vkoul@kernel.org> > --- > include/linux/dmaengine.h | 75 +++++++++++++++++++++++++++++++++++++++ > 1 file changed, 75 insertions(+) > > diff --git a/include/linux/dmaengine.h b/include/linux/dmaengine.h > index 6fbd5c99e30c..264643ca9209 100644 > --- a/include/linux/dmaengine.h > +++ b/include/linux/dmaengine.h > @@ -380,6 +380,73 @@ enum dma_slave_buswidth { > DMA_SLAVE_BUSWIDTH_64_BYTES = 64, > }; > > +/** > + * enum spi_transfer_cmd - spi transfer commands > + */ > +enum spi_transfer_cmd { > + SPI_TX = 1, > + SPI_RX, > + SPI_DUPLEX, > +}; > + > +/** > + * struct dmaengine_spi_config - spi config for peripheral > + * > + * @loopback_en: spi loopback enable when set > + * @clock_pol: clock polarity > + * @data_pol: data polarity > + * @pack_en: process tx/rx buffers as packed > + * @word_len: spi word length > + * @clk_div: source clock divider > + * @clk_src: serial clock > + * @cmd: spi cmd > + * @cs: chip select toggle > + * @rx_len: receive length for spi buffer > + */ > +struct dmaengine_spi_config { > + u8 loopback_en; > + u8 clock_pol; > + u8 data_pol; > + u8 pack_en; > + u8 word_len; > + u32 clk_div; > + u32 clk_src; > + u8 fragmentation; > + enum spi_transfer_cmd cmd; > + u8 cs; > + u32 rx_len; > +}; > + > +/** > + * struct dmaengine_i2c_config - i2c config for peripheral > + * > + * @pack_enable: process tx/rx buffers as packed > + * @cycle_count: clock cycles to be sent > + * @high_count: high period of clock > + * @low_count: low period of clock > + * @clk_div: source clock divider > + * @addr: i2c bus address > + * @strech: strech the clock at eot > + * @op: i2c cmd > + */ > +struct dmaengine_i2c_config { > + u8 pack_enable; > + u8 cycle_count; > + u8 high_count; > + u8 low_count; > + u16 clk_div; > + u8 addr; > + u8 strech; > + u8 op; > +}; > + > +enum dmaengine_peripheral { > + DMAENGINE_PERIPHERAL_SPI, > + DMAENGINE_PERIPHERAL_I2C, > + DMAENGINE_PERIPHERAL_UART, > + DMAENGINE_PERIPHERAL_LAST = DMAENGINE_PERIPHERAL_UART, > +}; > + > /** > * struct dma_slave_config - dma slave channel runtime config > * @direction: whether the data shall go in or out on this slave > @@ -418,6 +485,10 @@ enum dma_slave_buswidth { > * @slave_id: Slave requester id. Only valid for slave channels. The dma > * slave peripheral will have unique id as dma requester which need to be > * pass as slave config. > + * @peripheral: type of peripheral to DMA to/from > + * @set_config: set peripheral config > + * @spi: peripheral config for spi > + * @:i2c peripheral config for i2c > * > * This struct is passed in as configuration data to a DMA engine > * in order to set up a certain channel for DMA transport at runtime. > @@ -443,6 +514,10 @@ struct dma_slave_config { > u32 dst_port_window_size; > bool device_fc; > unsigned int slave_id; > + enum dmaengine_peripheral peripheral; > + u8 set_config; > + struct dmaengine_spi_config spi; > + struct dmaengine_i2c_config i2c; Would it be possible to reuse one of the existing feature already supported by DMAengine? We have DMA_PREP_CMD to give a command instead of a real transfer: dmaengine_prep_slave_single(tx_chan, config_data, config_len, DMA_MEM_TO_DEV, DMA_PREP_CMD); dmaengine_prep_slave_single(tx_chan, tx_buff, tx_len, DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); dma_async_issue_pending(tx_chan); or the metadata support: tx = dmaengine_prep_slave_single(tx_chan, tx_buff, tx_len, DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); dmaengine_desc_attach_metadata(tx, config_data, config_len); dma_async_issue_pending(tx_chan); By reading the driver itself, it is not clear if you always need to send the config for TX, or only when the config is changing and what happens if the first transfer (for SPI, since that is the only implemented one) is RX, when you don't send config at all... I'm concerned about the size increase of dma_slave_config (it grows by >30 bytes) and for DMAs with hundreds of channels (UDMA) it will add up to a sizeable amount. > }; > > /** > - Péter Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Hello Peter, On 25-08-20, 09:52, Peter Ujfalusi wrote: > Hi Vinod, > > On 24/08/2020 11.47, Vinod Koul wrote: > > Some complex dmaengine controllers have capability to program the > > peripheral device, so pass on the peripheral configuration as part of > > dma_slave_config > > > > Signed-off-by: Vinod Koul <vkoul@kernel.org> > > --- > > include/linux/dmaengine.h | 75 +++++++++++++++++++++++++++++++++++++++ > > 1 file changed, 75 insertions(+) > > > > diff --git a/include/linux/dmaengine.h b/include/linux/dmaengine.h > > index 6fbd5c99e30c..264643ca9209 100644 > > --- a/include/linux/dmaengine.h > > +++ b/include/linux/dmaengine.h > > @@ -380,6 +380,73 @@ enum dma_slave_buswidth { > > DMA_SLAVE_BUSWIDTH_64_BYTES = 64, > > }; > > > > +/** > > + * enum spi_transfer_cmd - spi transfer commands > > + */ > > +enum spi_transfer_cmd { > > + SPI_TX = 1, > > + SPI_RX, > > + SPI_DUPLEX, > > +}; > > + > > +/** > > + * struct dmaengine_spi_config - spi config for peripheral > > + * > > + * @loopback_en: spi loopback enable when set > > + * @clock_pol: clock polarity > > + * @data_pol: data polarity > > + * @pack_en: process tx/rx buffers as packed > > + * @word_len: spi word length > > + * @clk_div: source clock divider > > + * @clk_src: serial clock > > + * @cmd: spi cmd > > + * @cs: chip select toggle > > + * @rx_len: receive length for spi buffer > > + */ > > +struct dmaengine_spi_config { > > + u8 loopback_en; > > + u8 clock_pol; > > + u8 data_pol; > > + u8 pack_en; > > + u8 word_len; > > + u32 clk_div; > > + u32 clk_src; > > + u8 fragmentation; > > + enum spi_transfer_cmd cmd; > > + u8 cs; > > + u32 rx_len; > > +}; > > + > > +/** > > + * struct dmaengine_i2c_config - i2c config for peripheral > > + * > > + * @pack_enable: process tx/rx buffers as packed > > + * @cycle_count: clock cycles to be sent > > + * @high_count: high period of clock > > + * @low_count: low period of clock > > + * @clk_div: source clock divider > > + * @addr: i2c bus address > > + * @strech: strech the clock at eot > > + * @op: i2c cmd > > + */ > > +struct dmaengine_i2c_config { > > + u8 pack_enable; > > + u8 cycle_count; > > + u8 high_count; > > + u8 low_count; > > + u16 clk_div; > > + u8 addr; > > + u8 strech; > > + u8 op; > > +}; > > + > > +enum dmaengine_peripheral { > > + DMAENGINE_PERIPHERAL_SPI, > > + DMAENGINE_PERIPHERAL_I2C, > > + DMAENGINE_PERIPHERAL_UART, > > + DMAENGINE_PERIPHERAL_LAST = DMAENGINE_PERIPHERAL_UART, > > +}; > > + > > /** > > * struct dma_slave_config - dma slave channel runtime config > > * @direction: whether the data shall go in or out on this slave > > @@ -418,6 +485,10 @@ enum dma_slave_buswidth { > > * @slave_id: Slave requester id. Only valid for slave channels. The dma > > * slave peripheral will have unique id as dma requester which need to be > > * pass as slave config. > > + * @peripheral: type of peripheral to DMA to/from > > + * @set_config: set peripheral config > > + * @spi: peripheral config for spi > > + * @:i2c peripheral config for i2c > > * > > * This struct is passed in as configuration data to a DMA engine > > * in order to set up a certain channel for DMA transport at runtime. > > @@ -443,6 +514,10 @@ struct dma_slave_config { > > u32 dst_port_window_size; > > bool device_fc; > > unsigned int slave_id; > > + enum dmaengine_peripheral peripheral; > > + u8 set_config; > > + struct dmaengine_spi_config spi; > > + struct dmaengine_i2c_config i2c; > > Would it be possible to reuse one of the existing feature already > supported by DMAengine? > We have DMA_PREP_CMD to give a command instead of a real transfer: > dmaengine_prep_slave_single(tx_chan, config_data, config_len, > DMA_MEM_TO_DEV, DMA_PREP_CMD); > dmaengine_prep_slave_single(tx_chan, tx_buff, tx_len, DMA_MEM_TO_DEV, > DMA_PREP_INTERRUPT | DMA_CTRL_ACK); > dma_async_issue_pending(tx_chan); > > or the metadata support: > tx = dmaengine_prep_slave_single(tx_chan, tx_buff, tx_len, > DMA_MEM_TO_DEV, > DMA_PREP_INTERRUPT | DMA_CTRL_ACK); > dmaengine_desc_attach_metadata(tx, config_data, config_len); > dma_async_issue_pending(tx_chan); > > By reading the driver itself, it is not clear if you always need to send > the config for TX, or only when the config is changing and what happens > if the first transfer (for SPI, since that is the only implemented one) > is RX, when you don't send config at all... So this config is sent to driver everytime before the prep call (can be optimized to once if we have similar transfers in queue). This config is used to create the configuration passed to dmaengine which is used to actually program both dmaengine as well as peripheral registers (i2c/spi/etc), so we need a way to pass the spi/i2c config. I think prep cmd can be used to send this data, I do not see any issues with that, it would work if we want to go that route. I did have a prototype with metadata but didnt work very well, the problem is it assumes metadata for tx/rx but here i send the data everytime from client data. > I'm concerned about the size increase of dma_slave_config (it grows by > >30 bytes) and for DMAs with hundreds of channels (UDMA) it will add up > to a sizeable amount. I agree that is indeed a valid concern, that is the reason I tagged this as a RFC patch ;-) I see the prep_cmd is a better approach for this, anyone else has better suggestions? Thanks for looking in.
Hi Vinod, On 25/08/2020 10.10, Vinod Koul wrote: >>> /** >>> * struct dma_slave_config - dma slave channel runtime config >>> * @direction: whether the data shall go in or out on this slave >>> @@ -418,6 +485,10 @@ enum dma_slave_buswidth { >>> * @slave_id: Slave requester id. Only valid for slave channels. The dma >>> * slave peripheral will have unique id as dma requester which need to be >>> * pass as slave config. >>> + * @peripheral: type of peripheral to DMA to/from >>> + * @set_config: set peripheral config >>> + * @spi: peripheral config for spi >>> + * @:i2c peripheral config for i2c >>> * >>> * This struct is passed in as configuration data to a DMA engine >>> * in order to set up a certain channel for DMA transport at runtime. >>> @@ -443,6 +514,10 @@ struct dma_slave_config { >>> u32 dst_port_window_size; >>> bool device_fc; >>> unsigned int slave_id; >>> + enum dmaengine_peripheral peripheral; >>> + u8 set_config; >>> + struct dmaengine_spi_config spi; >>> + struct dmaengine_i2c_config i2c; >> >> Would it be possible to reuse one of the existing feature already >> supported by DMAengine? >> We have DMA_PREP_CMD to give a command instead of a real transfer: >> dmaengine_prep_slave_single(tx_chan, config_data, config_len, >> DMA_MEM_TO_DEV, DMA_PREP_CMD); >> dmaengine_prep_slave_single(tx_chan, tx_buff, tx_len, DMA_MEM_TO_DEV, >> DMA_PREP_INTERRUPT | DMA_CTRL_ACK); >> dma_async_issue_pending(tx_chan); >> >> or the metadata support: >> tx = dmaengine_prep_slave_single(tx_chan, tx_buff, tx_len, >> DMA_MEM_TO_DEV, >> DMA_PREP_INTERRUPT | DMA_CTRL_ACK); >> dmaengine_desc_attach_metadata(tx, config_data, config_len); >> dma_async_issue_pending(tx_chan); >> >> By reading the driver itself, it is not clear if you always need to send >> the config for TX, or only when the config is changing and what happens >> if the first transfer (for SPI, since that is the only implemented one) >> is RX, when you don't send config at all... > > So this config is sent to driver everytime before the prep call (can be > optimized to once if we have similar transfers in queue). I see that you queue the TREs in the prep callback. > This config is used to create the configuration passed to dmaengine > which is used to actually program both dmaengine as well as peripheral > registers (i2c/spi/etc), so we need a way to pass the spi/i2c config. But do you need to send it with each DMA_MEM_TO_DEV or only once? DMA_DEV_TO_MEM does not set the config, so I assume you must have one TX to initialize the peripheral as the first transfer. > I think prep cmd can be used to send this data, I do not see any issues > with that, it would work if we want to go that route. The only thing which might be an issue is that with the DMA_PREP_CMD the config_data is dma_addr_t (via dmaengine_prep_slave_single). > I did have a prototype with metadata but didnt work very well, the > problem is it assumes metadata for tx/rx but here i send the data > everytime from client data. Yes, the intended use case for metadata (per descriptor!) is for channels where each transfer might have different metadata needed for the given transfer (tx/rx). In your case you have semi static peripheral configuration data, which is not really changing between transfers. A compromise would be to add: void *peripheral_config; to the dma_slave_config, move the set_config inside of the device specific struct you are passing from a client to the core? >> I'm concerned about the size increase of dma_slave_config (it grows by >>> 30 bytes) and for DMAs with hundreds of channels (UDMA) it will add up >> to a sizeable amount. > > I agree that is indeed a valid concern, that is the reason I tagged this > as a RFC patch ;-) > > I see the prep_cmd is a better approach for this, anyone else has better > suggestions? > > Thanks for looking in. > - Péter Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Hi Peter, On 25-08-20, 11:00, Peter Ujfalusi wrote: > Hi Vinod, > > On 25/08/2020 10.10, Vinod Koul wrote: > >>> /** > >>> * struct dma_slave_config - dma slave channel runtime config > >>> * @direction: whether the data shall go in or out on this slave > >>> @@ -418,6 +485,10 @@ enum dma_slave_buswidth { > >>> * @slave_id: Slave requester id. Only valid for slave channels. The dma > >>> * slave peripheral will have unique id as dma requester which need to be > >>> * pass as slave config. > >>> + * @peripheral: type of peripheral to DMA to/from > >>> + * @set_config: set peripheral config > >>> + * @spi: peripheral config for spi > >>> + * @:i2c peripheral config for i2c > >>> * > >>> * This struct is passed in as configuration data to a DMA engine > >>> * in order to set up a certain channel for DMA transport at runtime. > >>> @@ -443,6 +514,10 @@ struct dma_slave_config { > >>> u32 dst_port_window_size; > >>> bool device_fc; > >>> unsigned int slave_id; > >>> + enum dmaengine_peripheral peripheral; > >>> + u8 set_config; > >>> + struct dmaengine_spi_config spi; > >>> + struct dmaengine_i2c_config i2c; > >> > >> Would it be possible to reuse one of the existing feature already > >> supported by DMAengine? > >> We have DMA_PREP_CMD to give a command instead of a real transfer: > >> dmaengine_prep_slave_single(tx_chan, config_data, config_len, > >> DMA_MEM_TO_DEV, DMA_PREP_CMD); > >> dmaengine_prep_slave_single(tx_chan, tx_buff, tx_len, DMA_MEM_TO_DEV, > >> DMA_PREP_INTERRUPT | DMA_CTRL_ACK); > >> dma_async_issue_pending(tx_chan); > >> > >> or the metadata support: > >> tx = dmaengine_prep_slave_single(tx_chan, tx_buff, tx_len, > >> DMA_MEM_TO_DEV, > >> DMA_PREP_INTERRUPT | DMA_CTRL_ACK); > >> dmaengine_desc_attach_metadata(tx, config_data, config_len); > >> dma_async_issue_pending(tx_chan); > >> > >> By reading the driver itself, it is not clear if you always need to send > >> the config for TX, or only when the config is changing and what happens > >> if the first transfer (for SPI, since that is the only implemented one) > >> is RX, when you don't send config at all... > > > > So this config is sent to driver everytime before the prep call (can be > > optimized to once if we have similar transfers in queue). > > I see that you queue the TREs in the prep callback. Yes > > This config is used to create the configuration passed to dmaengine > > which is used to actually program both dmaengine as well as peripheral > > registers (i2c/spi/etc), so we need a way to pass the spi/i2c config. > > But do you need to send it with each DMA_MEM_TO_DEV or only once? > DMA_DEV_TO_MEM does not set the config, so I assume you must have one TX > to initialize the peripheral as the first transfer. Correct and we do transfers on same without sending configuration again. > > I think prep cmd can be used to send this data, I do not see any issues > > with that, it would work if we want to go that route. > > The only thing which might be an issue is that with the DMA_PREP_CMD the > config_data is dma_addr_t (via dmaengine_prep_slave_single). Yes I came to same conclusion > > I did have a prototype with metadata but didnt work very well, the > > problem is it assumes metadata for tx/rx but here i send the data > > everytime from client data. > > Yes, the intended use case for metadata (per descriptor!) is for > channels where each transfer might have different metadata needed for > the given transfer (tx/rx). > > In your case you have semi static peripheral configuration data, which > is not really changing between transfers. > > A compromise would be to add: > void *peripheral_config; > to the dma_slave_config, move the set_config inside of the device > specific struct you are passing from a client to the core? That sounds more saner to me and uses existing interfaces cleanly. I think I like this option ;-) > >> I'm concerned about the size increase of dma_slave_config (it grows by > >>> 30 bytes) and for DMAs with hundreds of channels (UDMA) it will add up > >> to a sizeable amount. > > > > I agree that is indeed a valid concern, that is the reason I tagged this > > as a RFC patch ;-) > > > > I see the prep_cmd is a better approach for this, anyone else has better > > suggestions? > > > > Thanks for looking in. > > > > - Péter > > Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. > Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Hi Vinod, On 25/08/2020 14.02, Vinod Koul wrote: >> The only thing which might be an issue is that with the DMA_PREP_CMD the >> config_data is dma_addr_t (via dmaengine_prep_slave_single). > > Yes I came to same conclusion > >>> I did have a prototype with metadata but didnt work very well, the >>> problem is it assumes metadata for tx/rx but here i send the data >>> everytime from client data. >> >> Yes, the intended use case for metadata (per descriptor!) is for >> channels where each transfer might have different metadata needed for >> the given transfer (tx/rx). >> >> In your case you have semi static peripheral configuration data, which >> is not really changing between transfers. >> >> A compromise would be to add: >> void *peripheral_config; >> to the dma_slave_config, move the set_config inside of the device >> specific struct you are passing from a client to the core? > > That sounds more saner to me and uses existing interfaces cleanly. I > think I like this option ;-) The other option would be to use the descriptor metadata support and that might be even cleaner. In gpi_create_tre() via gpi_prep_slave_sg() you would set up the desc->tre[1] and desc->tre[2] for TX desc->tre[2] for RX in the desc, you add a new variable, let's say first_tre and set it to 1 for TX, 2 for RX. If you need to send a config, you attach it via either way metadata support allows you (get the pointer to desc->tre[0] or give a config struct to the DMA driver. In the metadata handler, you check if the transfer is TX, if it is, then you update desc->tre[0] (or give the pointer to the client) and update the first_tre to 0. In issue_pending, or a small helper which can be used to start the transfer you would do the queuing instead of prepare time: for (i = gpi_desc->first_tre; i < MAX_TRE; i++) gpi_queue_xfer(gpii, gpii_chan, &gpi_desc->tre[i], &wp); With this change it should work neatly without any change to dma_slave_config. > >>>> I'm concerned about the size increase of dma_slave_config (it grows by >>>>> 30 bytes) and for DMAs with hundreds of channels (UDMA) it will add up >>>> to a sizeable amount. >>> >>> I agree that is indeed a valid concern, that is the reason I tagged this >>> as a RFC patch ;-) >>> >>> I see the prep_cmd is a better approach for this, anyone else has better >>> suggestions? >>> >>> Thanks for looking in. >>> >> >> - Péter >> >> Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. >> Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki > - Péter Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
diff --git a/include/linux/dmaengine.h b/include/linux/dmaengine.h index 6fbd5c99e30c..264643ca9209 100644 --- a/include/linux/dmaengine.h +++ b/include/linux/dmaengine.h @@ -380,6 +380,73 @@ enum dma_slave_buswidth { DMA_SLAVE_BUSWIDTH_64_BYTES = 64, }; +/** + * enum spi_transfer_cmd - spi transfer commands + */ +enum spi_transfer_cmd { + SPI_TX = 1, + SPI_RX, + SPI_DUPLEX, +}; + +/** + * struct dmaengine_spi_config - spi config for peripheral + * + * @loopback_en: spi loopback enable when set + * @clock_pol: clock polarity + * @data_pol: data polarity + * @pack_en: process tx/rx buffers as packed + * @word_len: spi word length + * @clk_div: source clock divider + * @clk_src: serial clock + * @cmd: spi cmd + * @cs: chip select toggle + * @rx_len: receive length for spi buffer + */ +struct dmaengine_spi_config { + u8 loopback_en; + u8 clock_pol; + u8 data_pol; + u8 pack_en; + u8 word_len; + u32 clk_div; + u32 clk_src; + u8 fragmentation; + enum spi_transfer_cmd cmd; + u8 cs; + u32 rx_len; +}; + +/** + * struct dmaengine_i2c_config - i2c config for peripheral + * + * @pack_enable: process tx/rx buffers as packed + * @cycle_count: clock cycles to be sent + * @high_count: high period of clock + * @low_count: low period of clock + * @clk_div: source clock divider + * @addr: i2c bus address + * @strech: strech the clock at eot + * @op: i2c cmd + */ +struct dmaengine_i2c_config { + u8 pack_enable; + u8 cycle_count; + u8 high_count; + u8 low_count; + u16 clk_div; + u8 addr; + u8 strech; + u8 op; +}; + +enum dmaengine_peripheral { + DMAENGINE_PERIPHERAL_SPI, + DMAENGINE_PERIPHERAL_I2C, + DMAENGINE_PERIPHERAL_UART, + DMAENGINE_PERIPHERAL_LAST = DMAENGINE_PERIPHERAL_UART, +}; + /** * struct dma_slave_config - dma slave channel runtime config * @direction: whether the data shall go in or out on this slave @@ -418,6 +485,10 @@ enum dma_slave_buswidth { * @slave_id: Slave requester id. Only valid for slave channels. The dma * slave peripheral will have unique id as dma requester which need to be * pass as slave config. + * @peripheral: type of peripheral to DMA to/from + * @set_config: set peripheral config + * @spi: peripheral config for spi + * @:i2c peripheral config for i2c * * This struct is passed in as configuration data to a DMA engine * in order to set up a certain channel for DMA transport at runtime. @@ -443,6 +514,10 @@ struct dma_slave_config { u32 dst_port_window_size; bool device_fc; unsigned int slave_id; + enum dmaengine_peripheral peripheral; + u8 set_config; + struct dmaengine_spi_config spi; + struct dmaengine_i2c_config i2c; }; /**
Some complex dmaengine controllers have capability to program the peripheral device, so pass on the peripheral configuration as part of dma_slave_config Signed-off-by: Vinod Koul <vkoul@kernel.org> --- include/linux/dmaengine.h | 75 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 75 insertions(+)