deleted file mode 100644
@@ -1,58 +0,0 @@
-* MAX732x-compatible I/O expanders
-
-Required properties:
- - compatible: Should be one of the following:
- - "maxim,max7319": For the Maxim MAX7319
- - "maxim,max7320": For the Maxim MAX7320
- - "maxim,max7321": For the Maxim MAX7321
- - "maxim,max7322": For the Maxim MAX7322
- - "maxim,max7323": For the Maxim MAX7323
- - "maxim,max7324": For the Maxim MAX7324
- - "maxim,max7325": For the Maxim MAX7325
- - "maxim,max7326": For the Maxim MAX7326
- - "maxim,max7327": For the Maxim MAX7327
- - reg: I2C slave address for this device.
- - gpio-controller: Marks the device node as a GPIO controller.
- - #gpio-cells: Should be 2.
- - first cell is the GPIO number
- - second cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>.
- Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
-
-Optional properties:
-
- The I/O expander can detect input state changes, and thus optionally act as
- an interrupt controller. When the expander interrupt line is connected all the
- following properties must be set. For more information please see the
- interrupt controller device tree bindings documentation available at
- Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
-
- - interrupt-controller: Identifies the node as an interrupt controller.
- - #interrupt-cells: Number of cells to encode an interrupt source, shall be 2.
- - first cell is the pin number
- - second cell is used to specify flags
- - interrupts: Interrupt specifier for the controllers interrupt.
-
-Please refer to gpio.txt in this directory for details of the common GPIO
-bindings used by client devices.
-
-Example 1. MAX7325 with interrupt support enabled (CONFIG_GPIO_MAX732X_IRQ=y):
-
- expander: max7325@6d {
- compatible = "maxim,max7325";
- reg = <0x6d>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupt-parent = <&gpio4>;
- interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
- };
-
-Example 2. MAX7325 with interrupt support disabled (CONFIG_GPIO_MAX732X_IRQ=n):
-
- expander: max7325@6d {
- compatible = "maxim,max7325";
- reg = <0x6d>;
- gpio-controller;
- #gpio-cells = <2>;
- };
@@ -9,6 +9,10 @@ title: NXP PCA95xx I2C GPIO multiplexer
maintainers:
- Krzysztof Kozlowski <krzk@kernel.org>
+description: |+
+ Bindings for the family of I2C GPIO multiplexers/expanders: NXP PCA95xx,
+ Maxim MAX73xx
+
properties:
compatible:
enum:
@@ -17,6 +21,15 @@ properties:
- maxim,max7312
- maxim,max7313
- maxim,max7315
+ - maxim,max7319
+ - maxim,max7320
+ - maxim,max7321
+ - maxim,max7322
+ - maxim,max7323
+ - maxim,max7324
+ - maxim,max7325
+ - maxim,max7326
+ - maxim,max7327
- nxp,pca6416
- nxp,pca9505
- nxp,pca9534
@@ -69,11 +82,11 @@ properties:
reset-gpios:
description:
GPIO specification for the RESET input. This is an active low signal to
- the PCA953x.
+ the PCA953x. Not valid for Maxim MAX732x devices.
vcc-supply:
description:
- Optional power supply
+ Optional power supply. Not valid for Maxim MAX732x devices.
wakeup-source:
$ref: /schemas/types.yaml#/definitions/flag
@@ -103,6 +116,27 @@ required:
additionalProperties: false
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - maxim,max7320
+ - maxim,max7321
+ - maxim,max7322
+ - maxim,max7323
+ - maxim,max7324
+ - maxim,max7325
+ - maxim,max7326
+ - maxim,max7327
+ then:
+ properties:
+ reset-gpios:
+ maxItems: 0
+ vcc-supply:
+ maxItems: 0
+
examples:
- |
#include <dt-bindings/gpio/gpio.h>
@@ -164,3 +198,37 @@ examples:
ti,micbias = <0>; /* 2.1V */
};
};
+
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ i2c2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ // MAX7325 with interrupt support enabled
+ gpio@6d {
+ compatible = "maxim,max7325";
+ reg = <0x6d>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+ };
+ };
+
+ - |
+ i2c3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ // MAX7325 with interrupt support disabled
+ gpio@6e {
+ compatible = "maxim,max7325";
+ reg = <0x6e>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
Convert the Maxim MAX732x family of GPIO expanders bindings to device tree schema by merging it with existing PCA95xx schema. These are quite similar so merging reduces duplication. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> --- .../devicetree/bindings/gpio/gpio-max732x.txt | 58 --------------- .../bindings/gpio/gpio-pca95xx.yaml | 72 ++++++++++++++++++- 2 files changed, 70 insertions(+), 60 deletions(-) delete mode 100644 Documentation/devicetree/bindings/gpio/gpio-max732x.txt