@@ -461,6 +461,18 @@ config MTD_NAND_ARASAN
Enables the driver for the Arasan NAND flash controller on
Zynq Ultrascale+ MPSoC.
+config MTD_NAND_ROCKCHIP
+ tristate "Rockchip NAND controller"
+ depends on ARCH_ROCKCHIP && HAS_IOMEM
+ help
+ Enables support for NAND controller on Rockchip SoCs.
+ There are four different versions of NAND FLASH Controllers,
+ including:
+ NFC v600: RK2928, RK3066, RK3188
+ NFC v622: RK3036, RK3128
+ NFC v800: RK3308, RV1108
+ NFC v900: PX30, RK3326
+
comment "Misc"
config MTD_SM_COMMON
@@ -58,6 +58,7 @@ obj-$(CONFIG_MTD_NAND_STM32_FMC2) += stm32_fmc2_nand.o
obj-$(CONFIG_MTD_NAND_MESON) += meson_nand.o
obj-$(CONFIG_MTD_NAND_CADENCE) += cadence-nand-controller.o
obj-$(CONFIG_MTD_NAND_ARASAN) += arasan-nand-controller.o
+obj-$(CONFIG_MTD_NAND_ROCKCHIP) += rockchip-nand-controller.o
nand-objs := nand_base.o nand_legacy.o nand_bbt.o nand_timings.o nand_ids.o
nand-objs += nand_onfi.o
new file mode 100644
@@ -0,0 +1,1454 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Rockchip NAND Flash controller driver.
+ * Copyright (C) 2020 Rockchip Inc.
+ * Author: Yifeng Zhao <yifeng.zhao@rock-chips.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+/*
+ * NFC Page Data Layout:
+ * 1024 Bytes Data + 4Bytes sys data + 28Bytes~124Bytes ecc +
+ * 1024 Bytes Data + 4Bytes sys data + 28Bytes~124Bytes ecc +
+ * ......
+ * NAND Page Data Layout:
+ * 1024 * n Data + m Bytes oob
+ * Original Bad Block Mask Location:
+ * First byte of oob(spare).
+ * nand_chip->oob_poi data layout:
+ * 4Bytes sys data + .... + 4Bytes sys data + ecc data.
+ */
+
+/* NAND controller register definition */
+#define NFC_READ (0)
+#define NFC_WRITE (1)
+
+#define NFC_FMCTL (0x00)
+#define FMCTL_CE_SEL_M 0xFF
+#define FMCTL_CE_SEL(x) (1 << (x))
+#define FMCTL_WP BIT(8)
+#define FMCTL_RDY BIT(9)
+
+#define NFC_FMWAIT (0x04)
+#define FLCTL_RST BIT(0)
+#define FLCTL_WR (1) /* 0: read, 1: write */
+#define FLCTL_XFER_ST BIT(2)
+#define FLCTL_XFER_EN BIT(3)
+#define FLCTL_ACORRECT BIT(10) /* Auto correct error bits. */
+#define FLCTL_XFER_READY BIT(20)
+#define FLCTL_XFER_SECTOR (22)
+#define FLCTL_TOG_FIX BIT(29)
+
+#define BCHCTL_BANK_M (7 << 5)
+#define BCHCTL_BANK (5)
+
+#define DMA_ST BIT(0)
+#define DMA_WR (1) /* 0: write, 1: read */
+#define DMA_EN BIT(2)
+#define DMA_AHB_SIZE (3) /* 0: 1, 1: 2, 2: 4 */
+#define DMA_BURST_SIZE (6) /* 0: 1, 3: 4, 5: 8, 7: 16 */
+#define DMA_INC_NUM (9) /* 1 - 16 */
+
+#define ECC_ERR_CNT(x, e) ((((x) >> (e).low) & (e).low_mask) |\
+ (((x) >> (e).high) & (e).high_mask) << (e).low_bn)
+#define INT_DMA BIT(0)
+#define NFC_BANK (0x800)
+#define NFC_BANK_STEP (0x100)
+#define BANK_DATA (0x00)
+#define BANK_ADDR (0x04)
+#define BANK_CMD (0x08)
+#define NFC_SRAM0 (0x1000)
+#define NFC_SRAM1 (0x1400)
+#define NFC_SRAM_SIZE (0x400)
+#define NFC_TIMEOUT (500000)
+#define NFC_MAX_OOB_PER_STEP 128
+#define NFC_MIN_OOB_PER_STEP 64
+#define MAX_DATA_SIZE 0xFFFC
+#define MAX_ADDRESS_CYC 6
+#define NFC_ECC_MAX_MODES 4
+#define NFC_MAX_NSELS (8) /* Some Socs only have 1 or 2 CSs. */
+#define NFC_SYS_DATA_SIZE (4) /* 4 bytes sys data in oob pre 1024 data.*/
+#define RK_DEFAULT_CLOCK_RATE (150 * 1000 * 1000) /* 150 Mhz */
+#define ACCTIMING(csrw, rwpw, rwcs) ((csrw) << 12 | (rwpw) << 5 | (rwcs))
+
+enum nfc_type {
+ NFC_V6,
+ NFC_V8,
+ NFC_V9,
+};
+
+/**
+ * struct rk_ecc_cnt_status: represent a ecc status data.
+ * @err_flag_bit: error flag bit index at register.
+ * @low: ecc count low bit index at register.
+ * @low_mask: mask bit.
+ * @low_bn: ecc count low bit number.
+ * @high: ecc count high bit index at register.
+ * @high_mask: mask bit
+ */
+struct ecc_cnt_status {
+ u8 err_flag_bit;
+ u8 low;
+ u8 low_mask;
+ u8 low_bn;
+ u8 high;
+ u8 high_mask;
+};
+
+/*
+ * @type: nfc version
+ * @ecc_strengths: ecc strengths
+ * @ecc_cfgs: ecc config values
+ * @flctl_off: FLCTL register offset
+ * @bchctl_off: BCHCTL register offset
+ * @dma_data_buf_off: DMA_DATA_BUF register offset
+ * @dma_oob_buf_off: DMA_OOB_BUF register offset
+ * @dma_cfg_off: DMA_CFG register offset
+ * @dma_st_off: DMA_ST register offset
+ * @bch_st_off: BCG_ST register offset
+ * @randmz_off: RANDMZ register offset
+ * @int_en_off: interrupt enable register offset
+ * @int_clr_off: interrupt clean register offset
+ * @int_st_off: interrupt status register offset
+ * @oob0_off: oob0 register offset
+ * @oob1_off: oob1 register offset
+ * @ecc0: represent ECC0 status data
+ * @ecc1: represent ECC1 status data
+ */
+struct nfc_cfg {
+ enum nfc_type type;
+ u8 ecc_strengths[NFC_ECC_MAX_MODES];
+ u32 ecc_cfgs[NFC_ECC_MAX_MODES];
+ u32 flctl_off;
+ u32 bchctl_off;
+ u32 dma_cfg_off;
+ u32 dma_data_buf_off;
+ u32 dma_oob_buf_off;
+ u32 dma_st_off;
+ u32 bch_st_off;
+ u32 randmz_off;
+ u32 int_en_off;
+ u32 int_clr_off;
+ u32 int_st_off;
+ u32 oob0_off;
+ u32 oob1_off;
+ struct ecc_cnt_status ecc0;
+ struct ecc_cnt_status ecc1;
+};
+
+struct rk_nfc_nand_chip {
+ struct list_head node;
+ struct nand_chip chip;
+
+ u16 spare_per_sector;
+ u16 oob_buf_per_sector;
+ u16 boot_blks;
+ u16 boot_ecc;
+ u16 metadata_size;
+
+ u8 nsels;
+ u8 sels[0];
+ /* Nothing after this field. */
+};
+
+struct rk_nfc {
+ struct nand_controller controller;
+ const struct nfc_cfg *cfg;
+ struct device *dev;
+
+ struct clk *nfc_clk;
+ struct clk *ahb_clk;
+ void __iomem *regs;
+
+ u32 selected_bank;
+ u32 band_offset;
+ u32 cur_clk;
+
+ struct completion done;
+ struct list_head chips;
+
+ u8 *buffer;
+ u8 *page_buf;
+ u32 *oob_buf;
+ u32 buffer_size;
+
+ unsigned long assigned_cs;
+};
+
+static inline struct rk_nfc_nand_chip *to_rknand(struct nand_chip *chip)
+{
+ return container_of(chip, struct rk_nfc_nand_chip, chip);
+}
+
+static inline u8 *nand_data_ptr(struct nand_chip *chip, const u8 *p, int i)
+{
+ return (u8 *)p + i * chip->ecc.size;
+}
+
+static inline u8 *nand_oob_ptr(struct nand_chip *chip, int i)
+{
+ u8 *poi;
+
+ poi = chip->oob_poi + i * NFC_SYS_DATA_SIZE;
+
+ return poi;
+}
+
+static inline u8 *nand_oob_ecc_ptr(struct nand_chip *chip, int i)
+{
+ struct rk_nfc_nand_chip *rknand = to_rknand(chip);
+ u8 *poi;
+
+ poi = chip->oob_poi + rknand->metadata_size +
+ chip->ecc.bytes * i;
+
+ return poi;
+}
+
+static inline int rk_nfc_data_len(struct nand_chip *chip)
+{
+ struct rk_nfc_nand_chip *rknand = to_rknand(chip);
+
+ return chip->ecc.size + rknand->spare_per_sector;
+}
+
+static inline u8 *rk_nfc_data_ptr(struct nand_chip *chip, int i)
+{
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+
+ return nfc->buffer + i * rk_nfc_data_len(chip);
+}
+
+static inline u8 *rk_nfc_oob_ptr(struct nand_chip *chip, int i)
+{
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+
+ return nfc->buffer + i * rk_nfc_data_len(chip) + chip->ecc.size;
+}
+
+static void rk_nfc_select_chip(struct nand_chip *chip, int cs)
+{
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+ struct rk_nfc_nand_chip *rknand = to_rknand(chip);
+ u32 val;
+
+ if (cs < 0) {
+ nfc->selected_bank = -1;
+ /* Deselect the currently selected target. */
+ val = readl_relaxed(nfc->regs + NFC_FMCTL);
+ val &= ~FMCTL_CE_SEL_M;
+ writel(val, nfc->regs + NFC_FMCTL);
+ return;
+ }
+
+ nfc->selected_bank = rknand->sels[cs];
+ nfc->band_offset = NFC_BANK + nfc->selected_bank * NFC_BANK_STEP;
+
+ val = readl_relaxed(nfc->regs + NFC_FMCTL);
+ val &= ~FMCTL_CE_SEL_M;
+ val |= FMCTL_CE_SEL(nfc->selected_bank);
+
+ writel(val, nfc->regs + NFC_FMCTL);
+}
+
+static inline int rk_nfc_wait_ioready(struct rk_nfc *nfc)
+{
+ int rc;
+ u32 val;
+
+ rc = readl_relaxed_poll_timeout(nfc->regs + NFC_FMCTL, val,
+ val & FMCTL_RDY, 10, NFC_TIMEOUT);
+
+ return rc;
+}
+
+static void rk_nfc_read_buf(struct rk_nfc *nfc, u8 *buf, int len)
+{
+ int i;
+
+ for (i = 0; i < len; i++)
+ buf[i] = readb_relaxed(nfc->regs + nfc->band_offset +
+ BANK_DATA);
+}
+
+static void rk_nfc_write_buf(struct rk_nfc *nfc, const u8 *buf, int len)
+{
+ int i;
+
+ for (i = 0; i < len; i++)
+ writeb(buf[i], nfc->regs + nfc->band_offset + BANK_DATA);
+}
+
+static int rk_nfc_cmd(struct nand_chip *chip,
+ const struct nand_subop *subop)
+{
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+ unsigned int i, j, remaining, start;
+ int reg_offset = nfc->band_offset;
+ u8 *inbuf = NULL;
+ const u8 *outbuf;
+ u32 cnt = 0;
+ int ret = 0;
+
+ for (i = 0; i < subop->ninstrs; i++) {
+ const struct nand_op_instr *instr = &subop->instrs[i];
+
+ switch (instr->type) {
+ case NAND_OP_CMD_INSTR:
+ writeb(instr->ctx.cmd.opcode,
+ nfc->regs + reg_offset + BANK_CMD);
+ break;
+
+ case NAND_OP_ADDR_INSTR:
+ remaining = nand_subop_get_num_addr_cyc(subop, i);
+ start = nand_subop_get_addr_start_off(subop, i);
+
+ for (j = 0; j < 8 && j + start < remaining; j++)
+ writeb(instr->ctx.addr.addrs[j + start],
+ nfc->regs + reg_offset + BANK_ADDR);
+ break;
+
+ case NAND_OP_DATA_IN_INSTR:
+ case NAND_OP_DATA_OUT_INSTR:
+ start = nand_subop_get_data_start_off(subop, i);
+ cnt = nand_subop_get_data_len(subop, i);
+
+ if (instr->type == NAND_OP_DATA_OUT_INSTR) {
+ outbuf = instr->ctx.data.buf.out + start;
+ rk_nfc_write_buf(nfc, outbuf, cnt);
+ } else {
+ inbuf = instr->ctx.data.buf.in + start;
+ rk_nfc_read_buf(nfc, inbuf, cnt);
+ }
+ break;
+
+ case NAND_OP_WAITRDY_INSTR:
+ if (rk_nfc_wait_ioready(nfc) < 0) {
+ ret = -ETIMEDOUT;
+ dev_err(nfc->dev, "IO not ready\n");
+ }
+ break;
+ }
+ }
+
+ return ret;
+}
+
+static const struct nand_op_parser rk_nfc_op_parser = NAND_OP_PARSER(
+ NAND_OP_PARSER_PATTERN(
+ rk_nfc_cmd,
+ NAND_OP_PARSER_PAT_CMD_ELEM(true),
+ NAND_OP_PARSER_PAT_ADDR_ELEM(true, MAX_ADDRESS_CYC),
+ NAND_OP_PARSER_PAT_CMD_ELEM(true),
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
+ NAND_OP_PARSER_PAT_DATA_IN_ELEM(true, MAX_DATA_SIZE)),
+ NAND_OP_PARSER_PATTERN(
+ rk_nfc_cmd,
+ NAND_OP_PARSER_PAT_CMD_ELEM(true),
+ NAND_OP_PARSER_PAT_ADDR_ELEM(true, MAX_ADDRESS_CYC),
+ NAND_OP_PARSER_PAT_DATA_OUT_ELEM(true, MAX_DATA_SIZE),
+ NAND_OP_PARSER_PAT_CMD_ELEM(true),
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(true)),
+);
+
+static int rk_nfc_exec_op(struct nand_chip *chip,
+ const struct nand_operation *op,
+ bool check_only)
+{
+ if (!check_only)
+ rk_nfc_select_chip(chip, op->cs);
+
+ return nand_op_parser_exec_op(chip, &rk_nfc_op_parser, op,
+ check_only);
+}
+
+static int rk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
+ const struct nand_data_interface *conf)
+{
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+ const struct nand_sdr_timings *timings;
+ u32 rate, tc2rw, trwpw, trw2c;
+ u32 temp;
+
+ if (csline == NAND_DATA_IFACE_CHECK_ONLY)
+ return 0;
+
+ timings = nand_get_sdr_timings(conf);
+ if (IS_ERR(timings))
+ return -EOPNOTSUPP;
+
+ if (IS_ERR(nfc->nfc_clk))
+ rate = clk_get_rate(nfc->ahb_clk);
+ else
+ rate = clk_get_rate(nfc->nfc_clk);
+
+ /* Turn clock rate into kHz. */
+ rate /= 1000;
+
+ tc2rw = 1;
+ trw2c = 1;
+
+ trwpw = max(timings->tWC_min, timings->tRC_min) / 1000;
+ trwpw = DIV_ROUND_UP(trwpw * rate, 1000000);
+
+ temp = timings->tREA_max / 1000;
+ temp = DIV_ROUND_UP(temp * rate, 1000000);
+
+ if (trwpw < temp)
+ trwpw = temp;
+
+ /*
+ * ACCON: access timing control register
+ * -------------------------------------
+ * 31:18: reserved
+ * 17:12: csrw, clock cycles from the falling edge of CSn to the
+ * falling edge of RDn or WRn
+ * 11:11: reserved
+ * 10:05: rwpw, the width of RDn or WRn in processor clock cycles
+ * 04:00: rwcs, clock cycles from the rising edge of RDn or WRn to the
+ * rising edge of CSn
+ */
+ temp = ACCTIMING(tc2rw, trwpw, trw2c);
+ writel(temp, nfc->regs + NFC_FMWAIT);
+
+ return 0;
+}
+
+static int rk_nfc_hw_ecc_setup(struct nand_chip *chip,
+ struct nand_ecc_ctrl *ecc,
+ uint32_t strength)
+{
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+ u32 reg, i;
+
+ for (i = 0; i < NFC_ECC_MAX_MODES; i++) {
+ if (ecc->strength == nfc->cfg->ecc_strengths[i]) {
+ reg = nfc->cfg->ecc_cfgs[i];
+ break;
+ }
+ }
+
+ if (i >= NFC_ECC_MAX_MODES)
+ return -EINVAL;
+
+ writel(reg, nfc->regs + nfc->cfg->bchctl_off);
+
+ return 0;
+}
+
+static void rk_nfc_xfer_start(struct rk_nfc *nfc, u8 rw, u8 n_KB,
+ dma_addr_t dma_data, dma_addr_t dma_oob)
+{
+ u32 dma_reg, fl_reg, bch_reg;
+
+ dma_reg = DMA_ST | ((!rw) << DMA_WR) | DMA_EN | (2 << DMA_AHB_SIZE) |
+ (7 << DMA_BURST_SIZE) | (16 << DMA_INC_NUM);
+
+ fl_reg = (rw << FLCTL_WR) | FLCTL_XFER_EN | FLCTL_ACORRECT |
+ (n_KB << FLCTL_XFER_SECTOR) | FLCTL_TOG_FIX;
+
+ if (nfc->cfg->type == NFC_V6 || nfc->cfg->type == NFC_V8) {
+ bch_reg = readl_relaxed(nfc->regs + nfc->cfg->bchctl_off);
+ bch_reg = (bch_reg & (~BCHCTL_BANK_M)) |
+ (nfc->selected_bank << BCHCTL_BANK);
+ writel(bch_reg, nfc->regs + nfc->cfg->bchctl_off);
+ }
+
+ writel(dma_reg, nfc->regs + nfc->cfg->dma_cfg_off);
+ writel((u32)dma_data, nfc->regs + nfc->cfg->dma_data_buf_off);
+ writel((u32)dma_oob, nfc->regs + nfc->cfg->dma_oob_buf_off);
+ writel(fl_reg, nfc->regs + nfc->cfg->flctl_off);
+ fl_reg |= FLCTL_XFER_ST;
+ writel(fl_reg, nfc->regs + nfc->cfg->flctl_off);
+}
+
+static int rk_nfc_wait_for_xfer_done(struct rk_nfc *nfc)
+{
+ void __iomem *ptr;
+ int ret = 0;
+ u32 reg;
+
+ ptr = nfc->regs + nfc->cfg->flctl_off;
+
+ ret = readl_relaxed_poll_timeout(ptr, reg,
+ reg & FLCTL_XFER_READY,
+ 10, NFC_TIMEOUT);
+
+ return ret;
+}
+
+static int rk_nfc_write_page_raw(struct nand_chip *chip, const u8 *buf,
+ int oob_on, int page)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+ int ret = 0;
+ u32 i;
+
+ if (!buf)
+ memset(nfc->buffer, 0xff, mtd->writesize + mtd->oobsize);
+
+ for (i = 0; i < chip->ecc.steps; i++) {
+ /* Copy data to nfc buffer. */
+ if (buf)
+ memcpy(rk_nfc_data_ptr(chip, i),
+ nand_data_ptr(chip, buf, i),
+ chip->ecc.size);
+ /*
+ * The first four bytes of OOB are reserved for the
+ * boot ROM. In some debugging cases, sush as dump
+ * data and write back, the last four bytes stored
+ * in OOB need to be write back.
+ */
+ if (!i)
+ memcpy(rk_nfc_oob_ptr(chip, i),
+ nand_oob_ptr(chip, chip->ecc.steps - 1),
+ NFC_SYS_DATA_SIZE);
+ else
+ memcpy(rk_nfc_oob_ptr(chip, i),
+ nand_oob_ptr(chip, i - 1),
+ NFC_SYS_DATA_SIZE);
+ /* Copy ecc data to nfc buffer. */
+ memcpy(rk_nfc_oob_ptr(chip, i) + NFC_SYS_DATA_SIZE,
+ nand_oob_ecc_ptr(chip, i),
+ chip->ecc.bytes);
+ }
+
+ nand_prog_page_begin_op(chip, page, 0, NULL, 0);
+ rk_nfc_write_buf(nfc, buf, mtd->writesize + mtd->oobsize);
+ ret = nand_prog_page_end_op(chip);
+
+ /*
+ * Deselect the currently selected target after ops done,
+ * otherwise the NAND flash will has extra power consumption.
+ */
+ rk_nfc_select_chip(chip, -1);
+
+ return ret;
+}
+
+static int rk_nfc_write_oob(struct nand_chip *chip, int page)
+{
+ return rk_nfc_write_page_raw(chip, NULL, 1, page);
+}
+
+static int rk_nfc_write_page_hwecc(struct nand_chip *chip, const u8 *buf,
+ int oob_on, int page)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+ struct rk_nfc_nand_chip *rknand = to_rknand(chip);
+ struct nand_ecc_ctrl *ecc = &chip->ecc;
+ int oob_step = (ecc->bytes > 60) ? NFC_MAX_OOB_PER_STEP :
+ NFC_MIN_OOB_PER_STEP;
+ int pages_per_blk = mtd->erasesize / mtd->writesize;
+ int ret = 0, i, boot_rom_mode = 0;
+ dma_addr_t dma_data, dma_oob;
+ u32 reg;
+ u8 *oob;
+
+ nand_prog_page_begin_op(chip, page, 0, NULL, 0);
+
+ memcpy(nfc->page_buf, buf, mtd->writesize);
+
+ /*
+ * The first blocks (4, 8 or 16 depending on the device) are used
+ * by the boot ROM and the first 32 bits of oob need to link to
+ * the next page address in the same block.
+ * Config the ECC algorithm supported by the boot ROM.
+ */
+ if ((page < pages_per_blk * rknand->boot_blks) &&
+ (chip->options & NAND_IS_BOOT_MEDIUM)) {
+ boot_rom_mode = 1;
+ if (rknand->boot_ecc != ecc->strength)
+ rk_nfc_hw_ecc_setup(chip, ecc,
+ rknand->boot_ecc);
+ }
+
+ for (i = 0; i < ecc->steps; i++) {
+ if (!i) {
+ reg = 0xFFFFFFFF;
+ } else {
+ oob = chip->oob_poi + (i - 1) * NFC_SYS_DATA_SIZE;
+ reg = oob[0] | oob[1] << 8 | oob[2] << 16 |
+ oob[3] << 24;
+ }
+ if (!i && boot_rom_mode)
+ reg = (page & (pages_per_blk - 1)) * 4;
+
+ if (nfc->cfg->type == NFC_V9)
+ nfc->oob_buf[i] = reg;
+ else
+ nfc->oob_buf[i * oob_step / 4] = reg;
+ }
+
+ dma_data = dma_map_single(nfc->dev, (void *)nfc->page_buf,
+ mtd->writesize, DMA_TO_DEVICE);
+ dma_oob = dma_map_single(nfc->dev, nfc->oob_buf,
+ ecc->steps * oob_step,
+ DMA_TO_DEVICE);
+
+ reinit_completion(&nfc->done);
+ writel(INT_DMA, nfc->regs + nfc->cfg->int_en_off);
+
+ rk_nfc_xfer_start(nfc, NFC_WRITE, ecc->steps, dma_data,
+ dma_oob);
+ ret = wait_for_completion_timeout(&nfc->done,
+ msecs_to_jiffies(100));
+ if (!ret)
+ dev_warn(nfc->dev, "write: wait dma done timeout.\n");
+ /*
+ * Whether the DMA transfer is completed or not. The driver
+ * needs to check the NFC`s status register to see if the data
+ * transfer was completed.
+ */
+ ret = rk_nfc_wait_for_xfer_done(nfc);
+
+ dma_unmap_single(nfc->dev, dma_data, mtd->writesize,
+ DMA_TO_DEVICE);
+ dma_unmap_single(nfc->dev, dma_oob, ecc->steps * oob_step,
+ DMA_TO_DEVICE);
+
+ if (boot_rom_mode && rknand->boot_ecc != ecc->strength)
+ rk_nfc_hw_ecc_setup(chip, ecc, ecc->strength);
+
+ if (ret) {
+ ret = -EIO;
+ dev_err(nfc->dev,
+ "write: wait transfer done timeout.\n");
+ }
+
+ if (ret)
+ return ret;
+
+ ret = nand_prog_page_end_op(chip);
+
+ /*
+ * Deselect the currently selected target after ops done,
+ * otherwise the NAND flash will has extra power consumption.
+ */
+ rk_nfc_select_chip(chip, -1);
+
+ return ret;
+}
+
+static int rk_nfc_read_page_raw(struct nand_chip *chip, u8 *buf, int oob_on,
+ int page)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+ int i;
+
+ nand_read_page_op(chip, page, 0, NULL, 0);
+ rk_nfc_read_buf(nfc, nfc->buffer, mtd->writesize + mtd->oobsize);
+
+ /*
+ * Deselect the currently selected target after ops done,
+ * otherwise the NAND flash will has extra power consumption.
+ */
+ rk_nfc_select_chip(chip, -1);
+
+ for (i = 0; i < chip->ecc.steps; i++) {
+ /*
+ * The first four bytes of OOB are reserved for the
+ * boot ROM. In some debugging cases, sush as dump data
+ * and write back, it`s need to read out this four bytes,
+ * otherwise this information will be lost during write back.
+ */
+ if (!i)
+ memcpy(nand_oob_ptr(chip, chip->ecc.steps - 1),
+ rk_nfc_oob_ptr(chip, i),
+ NFC_SYS_DATA_SIZE);
+ else
+ memcpy(nand_oob_ptr(chip, i - 1),
+ rk_nfc_oob_ptr(chip, i),
+ NFC_SYS_DATA_SIZE);
+ /* Copy ecc data form nfc buffer. */
+ memcpy(nand_oob_ecc_ptr(chip, i),
+ rk_nfc_oob_ptr(chip, i) + NFC_SYS_DATA_SIZE,
+ chip->ecc.bytes);
+ /* Copy data form nfc buffer. */
+ if (buf)
+ memcpy(nand_data_ptr(chip, buf, i),
+ rk_nfc_data_ptr(chip, i),
+ chip->ecc.size);
+ }
+
+ return 0;
+}
+
+static int rk_nfc_read_oob(struct nand_chip *chip, int page)
+{
+ return rk_nfc_read_page_raw(chip, NULL, 1, page);
+}
+
+static int rk_nfc_read_page_hwecc(struct nand_chip *chip, u8 *buf, int oob_on,
+ int page)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+ struct rk_nfc_nand_chip *rknand = to_rknand(chip);
+ struct nand_ecc_ctrl *ecc = &chip->ecc;
+ int oob_step = (ecc->bytes > 60) ? NFC_MAX_OOB_PER_STEP :
+ NFC_MIN_OOB_PER_STEP;
+ int pages_per_blk = mtd->erasesize / mtd->writesize;
+ dma_addr_t dma_data, dma_oob;
+ int ret = 0, i, boot_rom_mode = 0;
+ int bitflips = 0, bch_st;
+ u8 *oob;
+ u32 tmp;
+
+ nand_read_page_op(chip, page, 0, NULL, 0);
+
+ dma_data = dma_map_single(nfc->dev, nfc->page_buf,
+ mtd->writesize,
+ DMA_FROM_DEVICE);
+ dma_oob = dma_map_single(nfc->dev, nfc->oob_buf,
+ ecc->steps * oob_step,
+ DMA_FROM_DEVICE);
+
+ /*
+ * The first blocks (4, 8 or 16 depending on the device)
+ * are used by the boot ROM.
+ * Config the ECC algorithm supported by the boot ROM.
+ */
+ if ((page < pages_per_blk * rknand->boot_blks) &&
+ (chip->options & NAND_IS_BOOT_MEDIUM)) {
+ boot_rom_mode = 1;
+ if (rknand->boot_ecc != ecc->strength)
+ rk_nfc_hw_ecc_setup(chip, ecc,
+ rknand->boot_ecc);
+ }
+
+ reinit_completion(&nfc->done);
+ writel(INT_DMA, nfc->regs + nfc->cfg->int_en_off);
+ rk_nfc_xfer_start(nfc, NFC_READ, ecc->steps, dma_data,
+ dma_oob);
+ ret = wait_for_completion_timeout(&nfc->done,
+ msecs_to_jiffies(100));
+ if (!ret)
+ dev_warn(nfc->dev, "read: wait dma done timeout.\n");
+ /*
+ * Whether the DMA transfer is completed or not. The driver
+ * needs to check the NFC`s status register to see if the data
+ * transfer was completed.
+ */
+ ret = rk_nfc_wait_for_xfer_done(nfc);
+ dma_unmap_single(nfc->dev, dma_data, mtd->writesize,
+ DMA_FROM_DEVICE);
+ dma_unmap_single(nfc->dev, dma_oob, ecc->steps * oob_step,
+ DMA_FROM_DEVICE);
+
+ if (ret) {
+ bitflips = -EIO;
+ dev_err(nfc->dev,
+ "read: wait transfer done timeout.\n");
+ goto out;
+ }
+
+ for (i = 1; i < ecc->steps; i++) {
+ oob = chip->oob_poi + (i - 1) * NFC_SYS_DATA_SIZE;
+ if (nfc->cfg->type == NFC_V9)
+ tmp = nfc->oob_buf[i];
+ else
+ tmp = nfc->oob_buf[i * oob_step / 4];
+ *oob++ = (u8)tmp;
+ *oob++ = (u8)(tmp >> 8);
+ *oob++ = (u8)(tmp >> 16);
+ *oob++ = (u8)(tmp >> 24);
+ }
+
+ for (i = 0; i < ecc->steps / 2; i++) {
+ bch_st = readl_relaxed(nfc->regs +
+ nfc->cfg->bch_st_off + i * 4);
+ if (bch_st & BIT(nfc->cfg->ecc0.err_flag_bit) ||
+ bch_st & BIT(nfc->cfg->ecc1.err_flag_bit)) {
+ mtd->ecc_stats.failed++;
+ /* ECC failed, return the minimum number of error bits */
+ bitflips = ecc->strength + 1;
+ } else {
+ ret = ECC_ERR_CNT(bch_st, nfc->cfg->ecc0);
+ mtd->ecc_stats.corrected += ret;
+ bitflips = max_t(u32, bitflips, ret);
+
+ ret = ECC_ERR_CNT(bch_st, nfc->cfg->ecc1);
+ mtd->ecc_stats.corrected += ret;
+ bitflips = max_t(u32, bitflips, ret);
+ }
+ }
+out:
+ memcpy(buf, nfc->page_buf, mtd->writesize);
+
+ if (boot_rom_mode && rknand->boot_ecc != ecc->strength)
+ rk_nfc_hw_ecc_setup(chip, ecc, ecc->strength);
+
+ if (bitflips > ecc->strength)
+ dev_err(nfc->dev, "read page: %x ecc error!\n", page);
+
+ /*
+ * Deselect the currently selected target after ops done,
+ * otherwise the NAND flash will has extra power consumption.
+ */
+ rk_nfc_select_chip(chip, -1);
+
+ return bitflips;
+}
+
+static inline void rk_nfc_hw_init(struct rk_nfc *nfc)
+{
+ /* Disable flash wp. */
+ writel(FMCTL_WP, nfc->regs + NFC_FMCTL);
+ /* Config default timing 40ns at 150 Mhz nfc clock. */
+ writel(0x1081, nfc->regs + NFC_FMWAIT);
+ /* Disable randomizer and DMA. */
+ writel(0, nfc->regs + nfc->cfg->randmz_off);
+ writel(0, nfc->regs + nfc->cfg->dma_cfg_off);
+ writel(FLCTL_RST, nfc->regs + nfc->cfg->flctl_off);
+}
+
+static irqreturn_t rk_nfc_irq(int irq, void *id)
+{
+ struct rk_nfc *nfc = id;
+ u32 sta, ien;
+
+ sta = readl_relaxed(nfc->regs + nfc->cfg->int_st_off);
+ ien = readl_relaxed(nfc->regs + nfc->cfg->int_en_off);
+
+ if (!(sta & ien))
+ return IRQ_NONE;
+
+ writel(sta, nfc->regs + nfc->cfg->int_clr_off);
+ writel(~sta & ien, nfc->regs + nfc->cfg->int_en_off);
+
+ complete(&nfc->done);
+
+ return IRQ_HANDLED;
+}
+
+static int rk_nfc_enable_clk(struct device *dev, struct rk_nfc *nfc)
+{
+ int ret;
+
+ if (!IS_ERR(nfc->nfc_clk)) {
+ ret = clk_prepare_enable(nfc->nfc_clk);
+ if (ret) {
+ dev_err(dev, "failed to enable nfc clk\n");
+ return ret;
+ }
+ }
+
+ ret = clk_prepare_enable(nfc->ahb_clk);
+ if (ret) {
+ dev_err(dev, "failed to enable ahb clk\n");
+ if (!IS_ERR(nfc->nfc_clk))
+ clk_disable_unprepare(nfc->nfc_clk);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void rk_nfc_disable_clk(struct rk_nfc *nfc)
+{
+ if (!IS_ERR(nfc->nfc_clk))
+ clk_disable_unprepare(nfc->nfc_clk);
+ clk_disable_unprepare(nfc->ahb_clk);
+}
+
+static int rk_nfc_ooblayout_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oob_region)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct rk_nfc_nand_chip *rknand = to_rknand(chip);
+
+ if (section)
+ return -ERANGE;
+
+ /*
+ * The beginning of the oob area stores the reserved data for the NFC,
+ * the size of the reserved data is NFC_SYS_DATA_SIZE bytes.
+ */
+ oob_region->length = rknand->metadata_size - NFC_SYS_DATA_SIZE - 2;
+ oob_region->offset = NFC_SYS_DATA_SIZE + 2;
+
+ return 0;
+}
+
+static int rk_nfc_ooblayout_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oob_region)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct rk_nfc_nand_chip *rknand = to_rknand(chip);
+
+ if (section)
+ return -ERANGE;
+
+ oob_region->offset = rknand->metadata_size;
+ oob_region->length = mtd->oobsize - oob_region->offset;
+
+ return 0;
+}
+
+static const struct mtd_ooblayout_ops rk_nfc_ooblayout_ops = {
+ .free = rk_nfc_ooblayout_free,
+ .ecc = rk_nfc_ooblayout_ecc,
+};
+
+static int rk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+ struct nand_ecc_ctrl *ecc = &chip->ecc;
+ const u8 *strengths = nfc->cfg->ecc_strengths;
+ u8 max_strength, nfc_max_strength;
+ int i;
+
+ nfc_max_strength = nfc->cfg->ecc_strengths[0];
+ /* If optional dt settings not present. */
+ if (!ecc->size || !ecc->strength ||
+ ecc->strength > nfc_max_strength) {
+ /* Use datasheet requirements. */
+ ecc->strength = chip->base.eccreq.strength;
+ ecc->size = chip->base.eccreq.step_size;
+
+ /* Align ECC strength and ECC size. */
+ if (chip->ecc.size < 1024) {
+ if (mtd->writesize > 512) {
+ chip->ecc.size = 1024;
+ chip->ecc.strength <<= 1;
+ } else {
+ dev_err(dev, "Unsupported ecc.size\n");
+ return -EINVAL;
+ }
+ } else {
+ chip->ecc.size = 1024;
+ }
+
+ ecc->steps = mtd->writesize / ecc->size;
+
+ /*
+ * HW ECC always requests the number of ECC bytes per 1024 byte
+ * blocks. 4 Bytes is oob for sys data.
+ */
+ max_strength = ((mtd->oobsize / ecc->steps) - 4) * 8 /
+ fls(8 * 1024);
+ if (max_strength > nfc_max_strength)
+ max_strength = nfc_max_strength;
+
+ for (i = 0; i < 4; i++) {
+ if (max_strength >= strengths[i])
+ break;
+ }
+
+ if (i >= 4) {
+ dev_err(nfc->dev, "Unsupported ECC strength\n");
+ return -EOPNOTSUPP;
+ }
+
+ ecc->strength = strengths[i];
+ }
+ ecc->steps = mtd->writesize / ecc->size;
+ ecc->bytes = DIV_ROUND_UP(ecc->strength * fls(8 * 1024), 8);
+ /* HW ECC always work with even numbers of ECC bytes. */
+ ecc->bytes = ALIGN(ecc->bytes, 2);
+
+ rk_nfc_hw_ecc_setup(chip, ecc, ecc->strength);
+
+ return 0;
+}
+
+static int rk_nfc_attach_chip(struct nand_chip *chip)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ struct device *dev = mtd->dev.parent;
+ struct rk_nfc *nfc = nand_get_controller_data(chip);
+ struct rk_nfc_nand_chip *rknand = to_rknand(chip);
+ struct nand_ecc_ctrl *ecc = &chip->ecc;
+ u8 *temp_buf;
+ int len, oob_len;
+ int ret;
+
+ if (chip->options & NAND_BUSWIDTH_16) {
+ dev_err(dev, "16 bits bus width not supported");
+ return -EINVAL;
+ }
+
+ if (ecc->mode != NAND_ECC_HW)
+ return 0;
+
+ ret = rk_nfc_ecc_init(dev, mtd);
+ if (ret)
+ return ret;
+ rknand->spare_per_sector = ecc->bytes + NFC_SYS_DATA_SIZE;
+ rknand->metadata_size = NFC_SYS_DATA_SIZE * ecc->steps;
+
+ if (rknand->metadata_size < NFC_SYS_DATA_SIZE + 2) {
+ dev_err(dev,
+ "Driver needs at least %d bytes of meta data\n",
+ NFC_SYS_DATA_SIZE + 2);
+ return -EIO;
+ }
+ len = mtd->writesize + mtd->oobsize;
+
+ /* Check buffer first, avoid duplicate alloc buffer. */
+ if (nfc->buffer) {
+ if (len > nfc->buffer_size) {
+ temp_buf = kzalloc(len, GFP_KERNEL | GFP_DMA);
+ if (!temp_buf)
+ return -ENOMEM;
+ kfree(nfc->buffer);
+ nfc->buffer = temp_buf;
+ nfc->buffer_size = len;
+
+ oob_len = ecc->steps * NFC_MAX_OOB_PER_STEP;
+ temp_buf = kzalloc(oob_len, GFP_KERNEL | GFP_DMA);
+ if (!temp_buf)
+ return -ENOMEM;
+ kfree(nfc->oob_buf);
+ nfc->oob_buf = (u32 *)temp_buf;
+ }
+ return 0;
+ }
+
+ nfc->buffer = kzalloc(len, GFP_KERNEL | GFP_DMA);
+ if (!nfc->buffer)
+ return -ENOMEM;
+
+ oob_len = ecc->steps * NFC_MAX_OOB_PER_STEP;
+ nfc->oob_buf = kzalloc(oob_len, GFP_KERNEL | GFP_DMA);
+ if (!nfc->oob_buf) {
+ kfree(nfc->buffer);
+ nfc->buffer = NULL;
+ nfc->oob_buf = NULL;
+ return -ENOMEM;
+ }
+
+ nfc->buffer_size = len;
+ nfc->page_buf = nfc->buffer;
+
+ chip->ecc.write_page_raw = rk_nfc_write_page_raw;
+ chip->ecc.write_page = rk_nfc_write_page_hwecc;
+ chip->ecc.write_oob_raw = rk_nfc_write_oob;
+ chip->ecc.write_oob = rk_nfc_write_oob;
+
+ chip->ecc.read_page_raw = rk_nfc_read_page_raw;
+ chip->ecc.read_page = rk_nfc_read_page_hwecc;
+ chip->ecc.read_oob_raw = rk_nfc_read_oob;
+ chip->ecc.read_oob = rk_nfc_read_oob;
+
+ return 0;
+}
+
+static const struct nand_controller_ops rk_nfc_controller_ops = {
+ .attach_chip = rk_nfc_attach_chip,
+ .exec_op = rk_nfc_exec_op,
+ .setup_data_interface = rk_nfc_setup_data_interface,
+};
+
+static int rk_nfc_nand_chip_init(struct device *dev, struct rk_nfc *nfc,
+ struct device_node *np)
+{
+ struct rk_nfc_nand_chip *rknand;
+ struct nand_chip *chip;
+ struct mtd_info *mtd;
+ int nsels;
+ u32 tmp;
+ int ret;
+ int i;
+
+ if (!of_get_property(np, "reg", &nsels))
+ return -ENODEV;
+ nsels /= sizeof(u32);
+ if (!nsels || nsels > NFC_MAX_NSELS) {
+ dev_err(dev, "invalid reg property size %d\n", nsels);
+ return -EINVAL;
+ }
+
+ rknand = devm_kzalloc(dev, sizeof(*rknand) + nsels * sizeof(u8),
+ GFP_KERNEL);
+ if (!rknand)
+ return -ENOMEM;
+
+ rknand->nsels = nsels;
+ for (i = 0; i < nsels; i++) {
+ ret = of_property_read_u32_index(np, "reg", i, &tmp);
+ if (ret) {
+ dev_err(dev, "reg property failure : %d\n", ret);
+ return ret;
+ }
+
+ if (tmp >= NFC_MAX_NSELS) {
+ dev_err(dev, "invalid CS: %u\n", tmp);
+ return -EINVAL;
+ }
+
+ if (test_and_set_bit(tmp, &nfc->assigned_cs)) {
+ dev_err(dev, "CS %u already assigned\n", tmp);
+ return -EINVAL;
+ }
+
+ rknand->sels[i] = tmp;
+ }
+
+ chip = &rknand->chip;
+ chip->controller = &nfc->controller;
+
+ nand_set_flash_node(chip, np);
+
+ nand_set_controller_data(chip, nfc);
+
+ chip->options |= NAND_USES_DMA | NAND_NO_SUBPAGE_WRITE;
+ chip->bbt_options = NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB;
+
+ /* Set default mode in case dt entry is missing. */
+ chip->ecc.mode = NAND_ECC_HW;
+
+ mtd = nand_to_mtd(chip);
+ mtd->owner = THIS_MODULE;
+ mtd->dev.parent = dev;
+
+ if (!mtd->name) {
+ dev_err(nfc->dev, "NAND label property is mandatory\n");
+ return -EINVAL;
+ }
+
+ mtd_set_ooblayout(mtd, &rk_nfc_ooblayout_ops);
+ rk_nfc_hw_init(nfc);
+ ret = nand_scan(chip, nsels);
+ if (ret)
+ return ret;
+
+ if (chip->options & NAND_IS_BOOT_MEDIUM) {
+ ret = of_property_read_u32(np, "rockchip,boot-blks", &tmp);
+ rknand->boot_blks = ret ? 0 : tmp;
+
+ ret = of_property_read_u32(np, "rockchip,boot-ecc-strength",
+ &tmp);
+ rknand->boot_ecc = ret ? chip->ecc.strength : tmp;
+ }
+
+ ret = mtd_device_register(mtd, NULL, 0);
+ if (ret) {
+ dev_err(dev, "mtd parse partition error\n");
+ nand_cleanup(chip);
+ return ret;
+ }
+
+ list_add_tail(&rknand->node, &nfc->chips);
+
+ return 0;
+}
+
+static void rk_nfc_chips_cleanup(struct rk_nfc *nfc)
+{
+ struct rk_nfc_nand_chip *rknand, *tmp;
+ struct nand_chip *chip;
+ int ret;
+
+ list_for_each_entry_safe(rknand, tmp, &nfc->chips, node) {
+ chip = &rknand->chip;
+ ret = mtd_device_unregister(nand_to_mtd(chip));
+ WARN_ON(ret);
+ nand_cleanup(chip);
+ list_del(&rknand->node);
+ }
+}
+
+static int rk_nfc_nand_chips_init(struct device *dev, struct rk_nfc *nfc)
+{
+ struct device_node *np = dev->of_node, *nand_np;
+ int nchips = of_get_child_count(np);
+ int ret;
+
+ if (!nchips || nchips > NFC_MAX_NSELS) {
+ dev_err(nfc->dev, "Incorrect number of NAND chips (%d)\n",
+ nchips);
+ return -EINVAL;
+ }
+
+ for_each_child_of_node(np, nand_np) {
+ ret = rk_nfc_nand_chip_init(dev, nfc, nand_np);
+ if (ret) {
+ of_node_put(nand_np);
+ rk_nfc_chips_cleanup(nfc);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static struct nfc_cfg nfc_v6_cfg = {
+ .type = NFC_V6,
+ .ecc_strengths = {60, 40, 24, 16},
+ .ecc_cfgs = {
+ 0x00040011, 0x00040001, 0x00000011, 0x00000001,
+ },
+ .flctl_off = 0x08,
+ .bchctl_off = 0x0C,
+ .dma_cfg_off = 0x10,
+ .dma_data_buf_off = 0x14,
+ .dma_oob_buf_off = 0x18,
+ .dma_st_off = 0x1C,
+ .bch_st_off = 0x20,
+ .randmz_off = 0x150,
+ .int_en_off = 0x16C,
+ .int_clr_off = 0x170,
+ .int_st_off = 0x174,
+ .oob0_off = 0x200,
+ .oob1_off = 0x230,
+ .ecc0 = {
+ .err_flag_bit = 2,
+ .low = 3,
+ .low_mask = 0x1F,
+ .low_bn = 5,
+ .high = 27,
+ .high_mask = 0x1,
+ },
+ .ecc1 = {
+ .err_flag_bit = 15,
+ .low = 16,
+ .low_mask = 0x1F,
+ .low_bn = 5,
+ .high = 29,
+ .high_mask = 0x1,
+ },
+};
+
+static struct nfc_cfg nfc_v8_cfg = {
+ .type = NFC_V8,
+ .ecc_strengths = {16, 16, 16, 16},
+ .ecc_cfgs = {
+ 0x00000001, 0x00000001, 0x00000001, 0x00000001,
+ },
+ .flctl_off = 0x08,
+ .bchctl_off = 0x0C,
+ .dma_cfg_off = 0x10,
+ .dma_data_buf_off = 0x14,
+ .dma_oob_buf_off = 0x18,
+ .dma_st_off = 0x1C,
+ .bch_st_off = 0x20,
+ .randmz_off = 0x150,
+ .int_en_off = 0x16C,
+ .int_clr_off = 0x170,
+ .int_st_off = 0x174,
+ .oob0_off = 0x200,
+ .oob1_off = 0x230,
+ .ecc0 = {
+ .err_flag_bit = 2,
+ .low = 3,
+ .low_mask = 0x1F,
+ .low_bn = 5,
+ .high = 27,
+ .high_mask = 0x1,
+ },
+ .ecc1 = {
+ .err_flag_bit = 15,
+ .low = 16,
+ .low_mask = 0x1F,
+ .low_bn = 5,
+ .high = 29,
+ .high_mask = 0x1,
+ },
+};
+
+static struct nfc_cfg nfc_v9_cfg = {
+ .type = NFC_V9,
+ .ecc_strengths = {70, 60, 40, 16},
+ .ecc_cfgs = {
+ 0x00000001, 0x06000001, 0x04000001, 0x02000001,
+ },
+ .flctl_off = 0x10,
+ .bchctl_off = 0x20,
+ .dma_cfg_off = 0x30,
+ .dma_data_buf_off = 0x34,
+ .dma_oob_buf_off = 0x38,
+ .dma_st_off = 0x3C,
+ .bch_st_off = 0x150,
+ .randmz_off = 0x208,
+ .int_en_off = 0x120,
+ .int_clr_off = 0x124,
+ .int_st_off = 0x128,
+ .oob0_off = 0x200,
+ .oob1_off = 0x204,
+ .ecc0 = {
+ .err_flag_bit = 2,
+ .low = 3,
+ .low_mask = 0x7F,
+ .low_bn = 7,
+ .high = 0,
+ .high_mask = 0x0,
+ },
+ .ecc1 = {
+ .err_flag_bit = 18,
+ .low = 19,
+ .low_mask = 0x7F,
+ .low_bn = 7,
+ .high = 0,
+ .high_mask = 0x0,
+ },
+};
+
+static const struct of_device_id rk_nfc_id_table[] = {
+ {
+ .compatible = "rockchip,px30-nfc",
+ .data = &nfc_v9_cfg
+ },
+ {
+ .compatible = "rockchip,rk2928-nfc",
+ .data = &nfc_v6_cfg
+ },
+ {
+ .compatible = "rockchip,rv1108-nfc",
+ .data = &nfc_v8_cfg
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rk_nfc_id_table);
+
+static int rk_nfc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct rk_nfc *nfc;
+ int ret, irq;
+
+ nfc = devm_kzalloc(dev, sizeof(*nfc), GFP_KERNEL);
+ if (!nfc)
+ return -ENOMEM;
+
+ nand_controller_init(&nfc->controller);
+ INIT_LIST_HEAD(&nfc->chips);
+ nfc->controller.ops = &rk_nfc_controller_ops;
+
+ nfc->cfg = of_device_get_match_data(dev);
+ nfc->dev = dev;
+
+ init_completion(&nfc->done);
+
+ nfc->regs = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(nfc->regs)) {
+ ret = PTR_ERR(nfc->regs);
+ goto release_nfc;
+ }
+
+ nfc->nfc_clk = devm_clk_get(dev, "nfc");
+ if (IS_ERR(nfc->nfc_clk)) {
+ dev_dbg(dev, "no nfc clk\n");
+ /* Some earlier models, such as rk3066, have no nfc clk. */
+ }
+
+ nfc->ahb_clk = devm_clk_get(dev, "ahb");
+ if (IS_ERR(nfc->ahb_clk)) {
+ dev_err(dev, "no ahb clk\n");
+ ret = PTR_ERR(nfc->ahb_clk);
+ goto release_nfc;
+ }
+
+ ret = rk_nfc_enable_clk(dev, nfc);
+ if (ret)
+ goto release_nfc;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "no nfc irq resource\n");
+ ret = -EINVAL;
+ goto clk_disable;
+ }
+
+ writel(0, nfc->regs + nfc->cfg->int_en_off);
+ ret = devm_request_irq(dev, irq, rk_nfc_irq, 0x0, "rk-nand", nfc);
+ if (ret) {
+ dev_err(dev, "failed to request nfc irq\n");
+ goto clk_disable;
+ }
+
+ platform_set_drvdata(pdev, nfc);
+
+ ret = rk_nfc_nand_chips_init(dev, nfc);
+ if (ret) {
+ dev_err(dev, "failed to init NAND chips\n");
+ goto clk_disable;
+ }
+ return 0;
+
+clk_disable:
+ rk_nfc_disable_clk(nfc);
+release_nfc:
+ return ret;
+}
+
+static int rk_nfc_remove(struct platform_device *pdev)
+{
+ struct rk_nfc *nfc = platform_get_drvdata(pdev);
+
+ kfree(nfc->buffer);
+ kfree(nfc->oob_buf);
+ rk_nfc_chips_cleanup(nfc);
+ rk_nfc_disable_clk(nfc);
+
+ return 0;
+}
+
+static int __maybe_unused rk_nfc_suspend(struct device *dev)
+{
+ struct rk_nfc *nfc = dev_get_drvdata(dev);
+
+ rk_nfc_disable_clk(nfc);
+
+ return 0;
+}
+
+static int __maybe_unused rk_nfc_resume(struct device *dev)
+{
+ struct rk_nfc *nfc = dev_get_drvdata(dev);
+ struct rk_nfc_nand_chip *rknand;
+ struct nand_chip *chip;
+ int ret;
+ u32 i;
+
+ ret = rk_nfc_enable_clk(dev, nfc);
+ if (ret)
+ return ret;
+
+ /* Reset NAND chip if VCC was powered off. */
+ list_for_each_entry(rknand, &nfc->chips, node) {
+ chip = &rknand->chip;
+ for (i = 0; i < rknand->nsels; i++)
+ nand_reset(chip, i);
+ }
+
+ return 0;
+}
+
+static const struct dev_pm_ops rk_nfc_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(rk_nfc_suspend, rk_nfc_resume)
+};
+
+static struct platform_driver rk_nfc_driver = {
+ .probe = rk_nfc_probe,
+ .remove = rk_nfc_remove,
+ .driver = {
+ .name = "rockchip-nfc",
+ .of_match_table = rk_nfc_id_table,
+ .pm = &rk_nfc_pm_ops,
+ },
+};
+
+module_platform_driver(rk_nfc_driver);
+
+MODULE_LICENSE("Dual MIT/GPL");
+MODULE_AUTHOR("Yifeng Zhao <yifeng.zhao@rock-chips.com>");
+MODULE_DESCRIPTION("Rockchip Nand Flash Controller Driver");
+MODULE_ALIAS("platform:rockchip-nand-controller");
This driver supports Rockchip NFC (NAND Flash Controller) found on RK3308, RK2928, RKPX30, RV1108 and other SOCs. The driver has been tested using 8-bit NAND interface on the ARM based RK3308 platform. Support Rockchip SoCs and NFC versions: - PX30 and RK3326(NFCv900). ECC: 16/40/60/70 bits/1KB. CLOCK: ahb and nfc. - RK3308 and RV1108(NFCv800). ECC: 16 bits/1KB. CLOCK: ahb and nfc. - RK3036 and RK3128(NFCv622). ECC: 16/24/40/60 bits/1KB. CLOCK: ahb and nfc. - RK3066, RK3188 and RK2928(NFCv600). ECC: 16/24/40/60 bits/1KB. CLOCK: ahb. Supported features: - Read full page data by DMA. - Support HW ECC(one step is 1KB). - Support 2 - 32K page size. - Support 8 CS(depend on SoCs) Limitations: - No support for the ecc step size is 512. - Untested on some SoCs. - No support for subpages. - No support for the builtin randomizer. - The original bad block mask is not supported. It is recommended to use the BBT(bad block table). Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com> --- Changes in v9: - The nfc->buffer will realloc while the page size of the second mtd is large than the first one - Fix coding style. - Remove struct rk_nfc_clk. - Prepend some function with rk_nfc_. - Replace function readl_poll_timeout_atomic with readl_relaxed_poll_timeout. - Remove function rk_nfc_read_byte and rk_nfc_write_byte. - Don't select the die if 'check_only == true' in function rk_nfc_exec_op. - Modify function rk_nfc_write_page and rk_nfc_write_page_raw. Changes in v8: None Changes in v7: - Rebase to linux-next. - Fix coding style. - Reserved 4 bytes at the beginning of the oob area. - Page raw read and write included ecc data. Changes in v6: - The mtd->name set by NAND label property. - Add some comments. - Fix compile error. Changes in v5: - Add boot blocks support with different ECC for bootROM. - Rename rockchip-nand.c to rockchip-nand-controller.c. - Unification of other variable names. - Remove some compatible define. Changes in v4: - Define platform data structure for the register offsets. - The compatible define with rkxx_nfc. - Use SET_SYSTEM_SLEEP_PM_OPS to define PM_OPS. - Use exec_op instead of legacy hooks. Changes in v3: None Changes in v2: - Fix compile error. - Include header files sorted by file name. drivers/mtd/nand/raw/Kconfig | 12 + drivers/mtd/nand/raw/Makefile | 1 + .../mtd/nand/raw/rockchip-nand-controller.c | 1454 +++++++++++++++++ 3 files changed, 1467 insertions(+) create mode 100644 drivers/mtd/nand/raw/rockchip-nand-controller.c