new file mode 100644
@@ -0,0 +1,140 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/microchip,sparx5-sgpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microsemi/Microchip Serial GPIO controller
+
+maintainers:
+ - Lars Povlsen <lars.povlsen@microchip.com>
+
+description: |
+ By using a serial interface, the SIO controller significantly extend
+ the number of available GPIOs with a minimum number of additional
+ pins on the device. The primary purpose of the SIO controllers is to
+ connect control signals from SFP modules and to act as an LED
+ controller.
+
+properties:
+ $nodename:
+ pattern: "^gpio@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - microchip,sparx5-sgpio
+ - mscc,ocelot-sgpio
+ - mscc,luton-sgpio
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ microchip,sgpio-port-ranges:
+ description: This is a sequence of tuples, defining intervals of
+ enabled ports in the serial input stream. The enabled ports must
+ match the hardware configuration in order for signals to be
+ properly written/read to/from the controller holding
+ registers. Being tuples, then number of arguments must be
+ even. The tuples mast be ordered (low, high) and are
+ inclusive.
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ items:
+ items:
+ - description: |
+ "low" indicates start bit number of range
+ minimum: 0
+ maximum: 31
+ - description: |
+ "high" indicates end bit number of range
+ minimum: 0
+ maximum: 31
+ minItems: 1
+ maxItems: 32
+
+ microchip,sgpio-frequency:
+ description: The sgpio controller frequency (Hz). This dictates
+ the serial bitstream speed, which again affects the latency in
+ getting control signals back and forth between external shift
+ registers. The speed must be no larger than half the system
+ clock, and larger than zero.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ default: 12500000
+
+patternProperties:
+ "^gpio@[0-1]$":
+ type: object
+ properties:
+ compatible:
+ const: microchip,sparx5-sgpio-bank
+
+ reg:
+ description: |
+ The GPIO bank number. "0" is designates the input pin bank,
+ "1" the output bank.
+ maxItems: 1
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ ngpios:
+ minimum: 1
+ maximum: 128
+
+ required:
+ - compatible
+ - reg
+ - gpio-controller
+ - '#gpio-cells'
+ - ngpios
+
+ additionalProperties: false
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - microchip,sgpio-port-ranges
+ - "#address-cells"
+ - "#size-cells"
+
+examples:
+ - |
+ sgpio2: gpio@1101059c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "microchip,sparx5-sgpio";
+ clocks = <&sys_clk>;
+ pinctrl-0 = <&sgpio2_pins>;
+ pinctrl-names = "default";
+ reg = <0x1101059c 0x100>;
+ microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
+ microchip,sgpio-frequency = <25000000>;
+ sgpio_in2: gpio@0 {
+ reg = <0>;
+ compatible = "microchip,sparx5-sgpio-bank";
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ sgpio_out2: gpio@1 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <1>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ };
This adds DT bindings for the Microsemi/Microchip SGPIO controller, bindings microchip,sparx5-sgpio, mscc,ocelot-sgpio and mscc,luton-sgpio. Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com> --- .../pinctrl/microchip,sparx5-sgpio.yaml | 140 ++++++++++++++++++ 1 file changed, 140 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml -- 2.25.1