[v3] spi: spi-sun6i: implement DMA-based transfer mode

Commit Message

Alexander Kochetkov Oct. 22, 2020, 7:52 a.m. UTC

From: Alexander Kochetkov <[e-mail]>

DMA-based transfer will be enabled if data length is larger than FIFO size
(64 bytes for A64). This greatly reduce number of interrupts for
transferring data.

For smaller data size PIO mode will be used. In PIO mode whole buffer will
be loaded into FIFO.

If driver failed to request DMA channels then it fallback for PIO mode.

Tested on SOPINE (https://www.pine64.org/sopine/)

Signed-off-by: Alexander Kochetkov <[e-mail]>
---
Changes in v3:
- Remove use_dma from struct sun6i_spi

Changes in v2:

- Fix 'checkpatch.pl --strict' warnings
- Optimezed DMA transfers. Fix burst size and address width for
 DMA transfers. The code works for me an I did some tests with different
 values and conditions. Empirically found that trigger level used for
 PIO mode also can be used for DMA mode (TRM for A64 lacks that 
 description)
- Handling inside sun6i_spi_handler() leaved as is, it explicity states that
 sun6i_spi_drain_fifo() is not used in DMA mode. Yes, if we call
 sun6i_spi_drain_fifo() after DMA transfer, it will not drain anything
 becase DMA already drain FIFO.
 I can remove condition if it's better without it.

 drivers/spi/spi-sun6i.c | 194 ++++++++++++++++++++++++++++++++++++----
 1 file changed, 176 insertions(+), 18 deletions(-)

Comments

Maxime Ripard Oct. 22, 2020, 3:43 p.m. UTC | #1

On Thu, Oct 22, 2020 at 10:52:21AM +0300, Alexander Kochetkov wrote:
> From: Alexander Kochetkov <[e-mail]>
> 
> DMA-based transfer will be enabled if data length is larger than FIFO size
> (64 bytes for A64). This greatly reduce number of interrupts for
> transferring data.
> 
> For smaller data size PIO mode will be used. In PIO mode whole buffer will
> be loaded into FIFO.
> 
> If driver failed to request DMA channels then it fallback for PIO mode.
> 
> Tested on SOPINE (https://www.pine64.org/sopine/)
> 
> Signed-off-by: Alexander Kochetkov <[e-mail]>

Acked-by: Maxime Ripard <[e-mail]>

Thanks!
Maxime

Mark Brown Oct. 26, 2020, 11:47 p.m. UTC | #2

On Thu, 22 Oct 2020 10:52:21 +0300, Alexander Kochetkov wrote:
> DMA-based transfer will be enabled if data length is larger than FIFO size
> (64 bytes for A64). This greatly reduce number of interrupts for
> transferring data.
> 
> For smaller data size PIO mode will be used. In PIO mode whole buffer will
> be loaded into FIFO.
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next

Thanks!

[1/1] spi: spi-sun6i: implement DMA-based transfer mode
      commit: 345980a3a5e5e1c99fc621e2ce878fb150ad2287

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

Patch

diff --git a/drivers/spi/spi-sun6i.c b/drivers/spi/spi-sun6i.c
index 19238e1b76b4..5336c5e32694 100644
--- a/drivers/spi/spi-sun6i.c
+++ b/drivers/spi/spi-sun6i.c
@@ -18,6 +18,7 @@ 
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/reset.h>
+#include <linux/dmaengine.h>
 
 #include <linux/spi/spi.h>
 
@@ -52,10 +53,12 @@ 
 
 #define SUN6I_FIFO_CTL_REG		0x18
 #define SUN6I_FIFO_CTL_RF_RDY_TRIG_LEVEL_MASK	0xff
+#define SUN6I_FIFO_CTL_RF_DRQ_EN		BIT(8)
 #define SUN6I_FIFO_CTL_RF_RDY_TRIG_LEVEL_BITS	0
 #define SUN6I_FIFO_CTL_RF_RST			BIT(15)
 #define SUN6I_FIFO_CTL_TF_ERQ_TRIG_LEVEL_MASK	0xff
 #define SUN6I_FIFO_CTL_TF_ERQ_TRIG_LEVEL_BITS	16
+#define SUN6I_FIFO_CTL_TF_DRQ_EN		BIT(24)
 #define SUN6I_FIFO_CTL_TF_RST			BIT(31)
 
 #define SUN6I_FIFO_STA_REG		0x1c
@@ -83,6 +86,8 @@ 
 struct sun6i_spi {
 	struct spi_master	*master;
 	void __iomem		*base_addr;
+	dma_addr_t		dma_addr_rx;
+	dma_addr_t		dma_addr_tx;
 	struct clk		*hclk;
 	struct clk		*mclk;
 	struct reset_control	*rstc;
@@ -182,6 +187,68 @@  static size_t sun6i_spi_max_transfer_size(struct spi_device *spi)
 	return SUN6I_MAX_XFER_SIZE - 1;
 }
 
+static int sun6i_spi_prepare_dma(struct sun6i_spi *sspi,
+				 struct spi_transfer *tfr)
+{
+	struct dma_async_tx_descriptor *rxdesc, *txdesc;
+	struct spi_master *master = sspi->master;
+
+	rxdesc = NULL;
+	if (tfr->rx_buf) {
+		struct dma_slave_config rxconf = {
+			.direction = DMA_DEV_TO_MEM,
+			.src_addr = sspi->dma_addr_rx,
+			.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES,
+			.src_maxburst = 8,
+		};
+
+		dmaengine_slave_config(master->dma_rx, &rxconf);
+
+		rxdesc = dmaengine_prep_slave_sg(master->dma_rx,
+						 tfr->rx_sg.sgl,
+						 tfr->rx_sg.nents,
+						 DMA_DEV_TO_MEM,
+						 DMA_PREP_INTERRUPT);
+		if (!rxdesc)
+			return -EINVAL;
+	}
+
+	txdesc = NULL;
+	if (tfr->tx_buf) {
+		struct dma_slave_config txconf = {
+			.direction = DMA_MEM_TO_DEV,
+			.dst_addr = sspi->dma_addr_tx,
+			.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES,
+			.dst_maxburst = 8,
+		};
+
+		dmaengine_slave_config(master->dma_tx, &txconf);
+
+		txdesc = dmaengine_prep_slave_sg(master->dma_tx,
+						 tfr->tx_sg.sgl,
+						 tfr->tx_sg.nents,
+						 DMA_MEM_TO_DEV,
+						 DMA_PREP_INTERRUPT);
+		if (!txdesc) {
+			if (rxdesc)
+				dmaengine_terminate_sync(master->dma_rx);
+			return -EINVAL;
+		}
+	}
+
+	if (tfr->rx_buf) {
+		dmaengine_submit(rxdesc);
+		dma_async_issue_pending(master->dma_rx);
+	}
+
+	if (tfr->tx_buf) {
+		dmaengine_submit(txdesc);
+		dma_async_issue_pending(master->dma_tx);
+	}
+
+	return 0;
+}
+
 static int sun6i_spi_transfer_one(struct spi_master *master,
 				  struct spi_device *spi,
 				  struct spi_transfer *tfr)
@@ -191,6 +258,7 @@  static int sun6i_spi_transfer_one(struct spi_master *master,
 	unsigned int start, end, tx_time;
 	unsigned int trig_level;
 	unsigned int tx_len = 0, rx_len = 0;
+	bool use_dma;
 	int ret = 0;
 	u32 reg;
 
@@ -201,6 +269,7 @@  static int sun6i_spi_transfer_one(struct spi_master *master,
 	sspi->tx_buf = tfr->tx_buf;
 	sspi->rx_buf = tfr->rx_buf;
 	sspi->len = tfr->len;
+	use_dma = master->can_dma ? master->can_dma(master, spi, tfr) : false;
 
 	/* Clear pending interrupts */
 	sun6i_spi_write(sspi, SUN6I_INT_STA_REG, ~0);
@@ -209,16 +278,34 @@  static int sun6i_spi_transfer_one(struct spi_master *master,
 	sun6i_spi_write(sspi, SUN6I_FIFO_CTL_REG,
 			SUN6I_FIFO_CTL_RF_RST | SUN6I_FIFO_CTL_TF_RST);
 
-	/*
-	 * Setup FIFO interrupt trigger level
-	 * Here we choose 3/4 of the full fifo depth, as it's the hardcoded
-	 * value used in old generation of Allwinner SPI controller.
-	 * (See spi-sun4i.c)
-	 */
-	trig_level = sspi->fifo_depth / 4 * 3;
-	sun6i_spi_write(sspi, SUN6I_FIFO_CTL_REG,
-			(trig_level << SUN6I_FIFO_CTL_RF_RDY_TRIG_LEVEL_BITS) |
-			(trig_level << SUN6I_FIFO_CTL_TF_ERQ_TRIG_LEVEL_BITS));
+	reg = 0;
+
+	if (!use_dma) {
+		/*
+		 * Setup FIFO interrupt trigger level
+		 * Here we choose 3/4 of the full fifo depth, as it's
+		 * the hardcoded value used in old generation of Allwinner
+		 * SPI controller. (See spi-sun4i.c)
+		 */
+		trig_level = sspi->fifo_depth / 4 * 3;
+	} else {
+		/*
+		 * Setup FIFO DMA request trigger level
+		 * We choose 1/2 of the full fifo depth, that value will
+		 * be used as DMA burst length.
+		 */
+		trig_level = sspi->fifo_depth / 2;
+
+		if (tfr->tx_buf)
+			reg |= SUN6I_FIFO_CTL_TF_DRQ_EN;
+		if (tfr->rx_buf)
+			reg |= SUN6I_FIFO_CTL_RF_DRQ_EN;
+	}
+
+	reg |= (trig_level << SUN6I_FIFO_CTL_RF_RDY_TRIG_LEVEL_BITS) |
+	       (trig_level << SUN6I_FIFO_CTL_TF_ERQ_TRIG_LEVEL_BITS);
+
+	sun6i_spi_write(sspi, SUN6I_FIFO_CTL_REG, reg);
 
 	/*
 	 * Setup the transfer control register: Chip Select,
@@ -300,16 +387,28 @@  static int sun6i_spi_transfer_one(struct spi_master *master,
 	sun6i_spi_write(sspi, SUN6I_XMIT_CNT_REG, tx_len);
 	sun6i_spi_write(sspi, SUN6I_BURST_CTL_CNT_REG, tx_len);
 
-	/* Fill the TX FIFO */
-	sun6i_spi_fill_fifo(sspi);
+	if (!use_dma) {
+		/* Fill the TX FIFO */
+		sun6i_spi_fill_fifo(sspi);
+	} else {
+		ret = sun6i_spi_prepare_dma(sspi, tfr);
+		if (ret) {
+			dev_warn(&master->dev,
+				 "%s: prepare DMA failed, ret=%d",
+				 dev_name(&spi->dev), ret);
+			return ret;
+		}
+	}
 
 	/* Enable the interrupts */
 	reg = SUN6I_INT_CTL_TC;
 
-	if (rx_len > sspi->fifo_depth)
-		reg |= SUN6I_INT_CTL_RF_RDY;
-	if (tx_len > sspi->fifo_depth)
-		reg |= SUN6I_INT_CTL_TF_ERQ;
+	if (!use_dma) {
+		if (rx_len > sspi->fifo_depth)
+			reg |= SUN6I_INT_CTL_RF_RDY;
+		if (tx_len > sspi->fifo_depth)
+			reg |= SUN6I_INT_CTL_TF_ERQ;
+	}
 
 	sun6i_spi_write(sspi, SUN6I_INT_CTL_REG, reg);
 
@@ -332,6 +431,11 @@  static int sun6i_spi_transfer_one(struct spi_master *master,
 
 	sun6i_spi_write(sspi, SUN6I_INT_CTL_REG, 0);
 
+	if (ret && use_dma) {
+		dmaengine_terminate_sync(master->dma_rx);
+		dmaengine_terminate_sync(master->dma_tx);
+	}
+
 	return ret;
 }
 
@@ -422,10 +526,25 @@  static int sun6i_spi_runtime_suspend(struct device *dev)
 	return 0;
 }
 
+static bool sun6i_spi_can_dma(struct spi_master *master,
+			      struct spi_device *spi,
+			      struct spi_transfer *xfer)
+{
+	struct sun6i_spi *sspi = spi_master_get_devdata(master);
+
+	/*
+	 * If the number of spi words to transfer is less or equal than
+	 * the fifo length we can just fill the fifo and wait for a single
+	 * irq, so don't bother setting up dma
+	 */
+	return xfer->len > sspi->fifo_depth;
+}
+
 static int sun6i_spi_probe(struct platform_device *pdev)
 {
 	struct spi_master *master;
 	struct sun6i_spi *sspi;
+	struct resource *mem;
 	int ret = 0, irq;
 
 	master = spi_alloc_master(&pdev->dev, sizeof(struct sun6i_spi));
@@ -437,7 +556,7 @@  static int sun6i_spi_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, master);
 	sspi = spi_master_get_devdata(master);
 
-	sspi->base_addr = devm_platform_ioremap_resource(pdev, 0);
+	sspi->base_addr = devm_platform_get_and_ioremap_resource(pdev, 0, &mem);
 	if (IS_ERR(sspi->base_addr)) {
 		ret = PTR_ERR(sspi->base_addr);
 		goto err_free_master;
@@ -494,6 +613,33 @@  static int sun6i_spi_probe(struct platform_device *pdev)
 		goto err_free_master;
 	}
 
+	master->dma_tx = dma_request_chan(&pdev->dev, "tx");
+	if (IS_ERR(master->dma_tx)) {
+		/* Check tx to see if we need defer probing driver */
+		if (PTR_ERR(master->dma_tx) == -EPROBE_DEFER) {
+			ret = -EPROBE_DEFER;
+			goto err_free_master;
+		}
+		dev_warn(&pdev->dev, "Failed to request TX DMA channel\n");
+		master->dma_tx = NULL;
+	}
+
+	master->dma_rx = dma_request_chan(&pdev->dev, "rx");
+	if (IS_ERR(master->dma_rx)) {
+		if (PTR_ERR(master->dma_rx) == -EPROBE_DEFER) {
+			ret = -EPROBE_DEFER;
+			goto err_free_dma_tx;
+		}
+		dev_warn(&pdev->dev, "Failed to request RX DMA channel\n");
+		master->dma_rx = NULL;
+	}
+
+	if (master->dma_tx && master->dma_rx) {
+		sspi->dma_addr_tx = mem->start + SUN6I_TXDATA_REG;
+		sspi->dma_addr_rx = mem->start + SUN6I_RXDATA_REG;
+		master->can_dma = sun6i_spi_can_dma;
+	}
+
 	/*
 	 * This wake-up/shutdown pattern is to be able to have the
 	 * device woken up, even if runtime_pm is disabled
@@ -501,7 +647,7 @@  static int sun6i_spi_probe(struct platform_device *pdev)
 	ret = sun6i_spi_runtime_resume(&pdev->dev);
 	if (ret) {
 		dev_err(&pdev->dev, "Couldn't resume the device\n");
-		goto err_free_master;
+		goto err_free_dma_rx;
 	}
 
 	pm_runtime_set_active(&pdev->dev);
@@ -519,6 +665,12 @@  static int sun6i_spi_probe(struct platform_device *pdev)
 err_pm_disable:
 	pm_runtime_disable(&pdev->dev);
 	sun6i_spi_runtime_suspend(&pdev->dev);
+err_free_dma_rx:
+	if (master->dma_rx)
+		dma_release_channel(master->dma_rx);
+err_free_dma_tx:
+	if (master->dma_tx)
+		dma_release_channel(master->dma_tx);
 err_free_master:
 	spi_master_put(master);
 	return ret;
@@ -526,8 +678,14 @@  static int sun6i_spi_probe(struct platform_device *pdev)
 
 static int sun6i_spi_remove(struct platform_device *pdev)
 {
+	struct spi_master *master = platform_get_drvdata(pdev);
+
 	pm_runtime_force_suspend(&pdev->dev);
 
+	if (master->dma_tx)
+		dma_release_channel(master->dma_tx);
+	if (master->dma_rx)
+		dma_release_channel(master->dma_rx);
 	return 0;
 }