[2/5] ARM: dts: add Samsung's exynos4412-based p4note boards

Message ID	20201031175836.47745-3-martin.juecker@gmail.com (mailing list archive)
State	Changes Requested
Headers	show Return-Path: <SRS0=vFf2=EG=vger.kernel.org=linux-samsung-soc-owner@kernel.org> From: =?utf-8?q?Martin_J=C3=BCcker?= <martin.juecker@gmail.com> To: linux-samsung-soc@vger.kernel.org Cc: kgene@kernel.org, krzk@kernel.org, devicetree@vger.kernel.org, =?utf-8?q?Martin_J=C3=BCcker?= <martin.juecker@gmail.com> Subject: [PATCH 2/5] ARM: dts: add Samsung's exynos4412-based p4note boards Date: Sat, 31 Oct 2020 18:58:34 +0100 Message-Id: <20201031175836.47745-3-martin.juecker@gmail.com> In-Reply-To: <20201031175836.47745-1-martin.juecker@gmail.com> References: <20201031175836.47745-1-martin.juecker@gmail.com> MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Precedence: bulk
Series	add exynos4412-based p4note device family support \| expand [v2,0/5] add exynos4412-based p4note device family support [1/5] dt-bindings: samsung: document bindings for p4note family boards [2/5] ARM: dts: add Samsung's exynos4412-based p4note boards [3/5] ARM: defconfig: add stmpe adc driver for p4note [4/5] ARM: defconfig: compile Atmel MXT touchscreeen as module [5/5] ARM: exynos: extend cpuidle support to p4note boards

On Mon, Nov 02, 2020 at 10:21:18PM +0100, Martin Juecker wrote: > On Mon, Nov 02, 2020 at 08:18:45PM +0100, Krzysztof Kozlowski wrote: > > On Sat, Oct 31, 2020 at 06:58:34PM +0100, Martin Jücker wrote: > > > The p4note family contains a couple of variants of the Galaxy Note 10.1 > > > tablet with mainly different modems. The GT-N8010/GT-N8013 is the wifi > > > only version. > > > > The subject is v1. Did you send correct patch? > > I probably messed up with git send-email here. I need some more time to > get used to it. The patch is indeed v2. > > > > > > > > > Signed-off-by: Martin Jücker <martin.juecker@gmail.com> > > > --- > > > arch/arm/boot/dts/Makefile | 1 + > > > arch/arm/boot/dts/exynos4412-p4note-n8010.dts | 16 + > > > arch/arm/boot/dts/exynos4412-p4note.dtsi | 1128 +++++++++++++++++ > > > 3 files changed, 1145 insertions(+) > > > create mode 100644 arch/arm/boot/dts/exynos4412-p4note-n8010.dts > > > create mode 100644 arch/arm/boot/dts/exynos4412-p4note.dtsi > > > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > > index 4572db3fa5ae..951853e55edb 100644 > > > --- a/arch/arm/boot/dts/Makefile > > > +++ b/arch/arm/boot/dts/Makefile > > > @@ -195,6 +195,7 @@ dtb-$(CONFIG_ARCH_EXYNOS4) += \ > > > exynos4412-odroidx.dtb \ > > > exynos4412-odroidx2.dtb \ > > > exynos4412-origen.dtb \ > > > + exynos4412-p4note-n8010.dtb \ > > > exynos4412-smdk4412.dtb \ > > > exynos4412-tiny4412.dtb \ > > > exynos4412-trats2.dtb > > > diff --git a/arch/arm/boot/dts/exynos4412-p4note-n8010.dts b/arch/arm/boot/dts/exynos4412-p4note-n8010.dts > > > new file mode 100644 > > > index 000000000000..f99358750e01 > > > --- /dev/null > > > +++ b/arch/arm/boot/dts/exynos4412-p4note-n8010.dts > > > @@ -0,0 +1,16 @@ > > > +// SPDX-License-Identifier: GPL-2.0 > > > +/* > > > + * Samsung's Galaxy Note 10.1 - N801x (wifi only version) > > > + * > > > + * Copyright (c) 2020 Martin Jücker <martin.juecker@gmail.com> > > > + */ > > > + > > > +/dts-v1/; > > > +#include "exynos4412-p4note.dtsi" > > > + > > > +/ { > > > + model = "Samsung Galaxy Note 10.1 (GT-N8010/N8013) based on Exynos4412"; > > > + compatible = "samsung,n8010", "samsung,p4note", "samsung,exynos4412", "samsung,exynos4"; > > > + > > > + /* this is the base variant without any kind of modem */ > > > +}; > > > diff --git a/arch/arm/boot/dts/exynos4412-p4note.dtsi b/arch/arm/boot/dts/exynos4412-p4note.dtsi > > > new file mode 100644 > > > index 000000000000..15b6acbbecb2 > > > --- /dev/null > > > +++ b/arch/arm/boot/dts/exynos4412-p4note.dtsi > > > @@ -0,0 +1,1128 @@ > > > +// SPDX-License-Identifier: GPL-2.0 > > > +/* > > > + * Samsung's Exynos4412 based p4note device family base DT > > > + * > > > + * Copyright (c) 2020 Martin Jücker <martin.juecker@gmail.com> > > > > Multiple parts of this file look like copied from the existing ones. Few > > comments are the same. The v1 duplicated even few minor issues like not > > that good naming of nodes. It looks like it is not only based on > > existing sources, but uses parts of them directly. If it is true, then > > include the copyright of original work as well. > > https://www.gnu.org/prep/maintain/html_node/Copyright-Notices.html > > > > I had a look through multiple files and ended up with a mix of copying > and writing nodes myself. Most if not all of the copying is from the > midas dt, is it enough to add a note that this file is based on the > midas dt or should I go with the same approach like midas and only add > the samsung copyright here? I don't care too much what's in the header. In such case we mention that works is based on the file, as you suggest, and usually we keep the copyright of original file. > > > > > + */ > > > + > > > +/dts-v1/; > > > +#include "exynos4412.dtsi" > > > +#include "exynos4412-ppmu-common.dtsi" > > > + > > > +#include <dt-bindings/clock/maxim,max77686.h> > > > +#include <dt-bindings/gpio/gpio.h> > > > +#include <dt-bindings/input/linux-event-codes.h> > > > +#include <dt-bindings/interrupt-controller/irq.h> > > > +#include <dt-bindings/pinctrl/samsung.h> > > > + > > > +/ { > > > + compatible = "samsung,p4note", "samsung,exynos4412", "samsung,exynos4"; > > > + > > > + memory@40000000 { > > > + device_type = "memory"; > > > + reg = <0x40000000 0x80000000>; > > > + }; > > > + > > > + chosen { > > > + stdout-path = &serial_2; > > > + }; > > > + > > > + firmware@204f000 { > > > + compatible = "samsung,secure-firmware"; > > > + reg = <0x0204F000 0x1000>; > > > + }; > > > + > > > + fixed-rate-clocks { > > > + xxti { > > > + compatible = "samsung,clock-xxti"; > > > + clock-frequency = <0>; > > > + }; > > > + > > > + xusbxti { > > > + compatible = "samsung,clock-xusbxti"; > > > + clock-frequency = <24000000>; > > > + }; > > > + }; > > > + > > > + gpio-keys { > > > + compatible = "gpio-keys"; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&gpio_keys>; > > > + > > > + key-down { > > > + gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; > > > + linux,code = <KEY_VOLUMEDOWN>; > > > + label = "volume down"; > > > + debounce-interval = <10>; > > > + }; > > > + > > > + key-up { > > > + gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; > > > + linux,code = <KEY_VOLUMEUP>; > > > + label = "volume up"; > > > + debounce-interval = <10>; > > > + }; > > > + > > > + key-power { > > > + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; > > > + linux,code = <KEY_POWER>; > > > + label = "power"; > > > + debounce-interval = <10>; > > > + wakeup-source; > > > + }; > > > + }; > > > + > > > + voltage-regulator-1 { > > > + compatible = "regulator-fixed"; > > > + regulator-name = "TSP_LDO1"; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&tsp_reg_gpio_1>; > > > + gpios = <&gpm4 5 GPIO_ACTIVE_HIGH>; > > > + enable-active-high; > > > + regulator-always-on; > > > + }; > > > + > > > + voltage-regulator-2 { > > > + compatible = "regulator-fixed"; > > > + regulator-name = "TSP_LDO2"; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&tsp_reg_gpio_2>; > > > + gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; > > > + enable-active-high; > > > + regulator-always-on; > > > + }; > > > + > > > + voltage-regulator-3 { > > > + compatible = "regulator-fixed"; > > > + regulator-name = "TSP_LDO3"; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&tsp_reg_gpio_3>; > > > + gpios = <&gpb 7 GPIO_ACTIVE_HIGH>; > > > + startup-delay-us = <20000>; > > > + enable-active-high; > > > + regulator-always-on; > > > + }; > > > + > > > + wlan_pwrseq: sdhci3-pwrseq { > > > + compatible = "mmc-pwrseq-simple"; > > > + reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>; > > > + pinctrl-0 = <&wifi_reset>; > > > + pinctrl-names = "default"; > > > + clocks = <&max77686 MAX77686_CLK_PMIC>; > > > + clock-names = "ext_clock"; > > > + }; > > > + > > > + i2c-gpio-1 { > > > + compatible = "i2c-gpio"; > > > + sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > > > + scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > > > + i2c-gpio,delay-us = <2>; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + > > > + magnetometer@c { > > > + compatible = "asahi-kasei,ak8975"; > > > + reg = <0x0c>; > > > + pinctrl-0 = <&ak8975_irq>; > > > + pinctrl-names = "default"; > > > + interrupt-parent = <&gpm4>; > > > + interrupts = <7 IRQ_TYPE_EDGE_RISING>; > > > + }; > > > + }; > > > + > > > + i2c-gpio-2 { > > > + compatible = "i2c-gpio"; > > > + sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > > > + scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > > > + i2c-gpio,delay-us = <2>; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + > > > + fuel-gauge@36 { > > > + compatible = "maxim,max17042"; > > > + reg = <0x36>; > > > + pinctrl-0 = <&fuel_alert_irq>; > > > + pinctrl-names = "default"; > > > + interrupt-parent = <&gpx2>; > > > + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; > > > + maxim,rsns-microohm = <10000>; > > > + maxim,over-heat-temp = <600>; > > > + maxim,over-volt = <4300>; > > > + }; > > > + }; > > > + > > > + i2c-gpio-3 { > > > + compatible = "i2c-gpio"; > > > + sda-gpios = <&gpm4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > > > + scl-gpios = <&gpm4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > > > + i2c-gpio,delay-us = <5>; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + > > > + adc@41 { > > > + compatible = "st,stmpe811"; > > > + reg = <0x41>; > > > + pinctrl-0 = <&stmpe_adc_irq>; > > > + pinctrl-names = "default"; > > > + interrupt-parent = <&gpx0>; > > > + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; > > > + interrupt-controller; > > > + irq-trigger = <0x1>; > > > + st,adc-freq = <3>; > > > + st,mod-12b = <1>; > > > + st,ref-sel = <0>; > > > + st,sample-time = <3>; > > > + > > > + stmpe_adc { > > > + compatible = "st,stmpe-adc"; > > > + #io-channel-cells = <1>; > > > + st,norequest-mask = <0x2F>; > > > + }; > > > + }; > > > + }; > > > +}; > > > + > > > +&adc { > > > + vdd-supply = <&ldo3_reg>; > > > + /* not verified */ > > > + status = "okay"; > > > +}; > > > + > > > +&bus_dmc { > > > + devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; > > > + vdd-supply = <&buck1_reg>; > > > + status = "okay"; > > > +}; > > > + > > > +&bus_acp { > > > + devfreq = <&bus_dmc>; > > > + status = "okay"; > > > +}; > > > + > > > +&bus_c2c { > > > + devfreq = <&bus_dmc>; > > > + status = "okay"; > > > +}; > > > + > > > +&bus_leftbus { > > > + devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; > > > + vdd-supply = <&buck3_reg>; > > > + status = "okay"; > > > +}; > > > + > > > +&bus_rightbus { > > > + devfreq = <&bus_leftbus>; > > > + status = "okay"; > > > +}; > > > + > > > +&bus_display { > > > + devfreq = <&bus_leftbus>; > > > + status = "okay"; > > > +}; > > > + > > > +&bus_fsys { > > > + devfreq = <&bus_leftbus>; > > > + status = "okay"; > > > +}; > > > + > > > +&bus_peri { > > > + devfreq = <&bus_leftbus>; > > > + status = "okay"; > > > +}; > > > + > > > +&bus_mfc { > > > + devfreq = <&bus_leftbus>; > > > + status = "okay"; > > > +}; > > > + > > > +&cpu0 { > > > + cpu0-supply = <&buck2_reg>; > > > +}; > > > + > > > +&cpu_thermal { > > > + cooling-maps { > > > + map0 { > > > + /* Corresponds to 800MHz at freq_table */ > > > + cooling-device = <&cpu0 7 7>, <&cpu1 7 7>, <&cpu2 7 7>, <&cpu3 7 7>; > > > + }; > > > + map1 { > > > + /* Corresponds to 200MHz at freq_table */ > > > + cooling-device = <&cpu0 13 13>, <&cpu1 13 13>, <&cpu2 13 13>, <&cpu3 13 13>; > > > > This is too long. Please split it at 80 with indentation of next line > > starting at < from the previous one. > > > > Okay > > > > > > + }; > > > + }; > > > +}; > > > + > > > +&exynos_usbphy { > > > + status = "okay"; > > > +}; > > > + > > > +&fimd { > > > + pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>; > > > + pinctrl-names = "default"; > > > + status = "okay"; > > > + > > > + display-timings { > > > + timing0 { > > > + clock-frequency = <66666666>; > > > + hactive = <1280>; > > > + vactive = <800>; > > > + hfront-porch = <18>; > > > + hback-porch = <36>; > > > + hsync-len = <16>; > > > + vback-porch = <16>; > > > + vfront-porch = <4>; > > > + vsync-len = <3>; > > > + hsync-active = <1>; > > > + }; > > > + }; > > > > What happened with Marek's comment about this? > > > > Should have mentioned it in the introduction mail. I had a look at the > simple panel driver and it's not enough for the display in the p4note. I > asked Marek in IRC whether it's ok to have this in a separate patch set > to have a fully working display and he agreed. Ah, ok. Best regards, Krzysztof

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 4572db3fa5ae..951853e55edb 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -195,6 +195,7 @@ dtb-$(CONFIG_ARCH_EXYNOS4) += \ exynos4412-odroidx.dtb \ exynos4412-odroidx2.dtb \ exynos4412-origen.dtb \ + exynos4412-p4note-n8010.dtb \ exynos4412-smdk4412.dtb \ exynos4412-tiny4412.dtb \ exynos4412-trats2.dtb diff --git a/arch/arm/boot/dts/exynos4412-p4note-n8010.dts b/arch/arm/boot/dts/exynos4412-p4note-n8010.dts new file mode 100644 index 000000000000..f99358750e01 --- /dev/null +++ b/arch/arm/boot/dts/exynos4412-p4note-n8010.dts @@ -0,0 +1,16 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Samsung's Galaxy Note 10.1 - N801x (wifi only version) + * + * Copyright (c) 2020 Martin Jücker <martin.juecker@gmail.com> + */ + +/dts-v1/; +#include "exynos4412-p4note.dtsi" + +/ { + model = "Samsung Galaxy Note 10.1 (GT-N8010/N8013) based on Exynos4412"; + compatible = "samsung,n8010", "samsung,p4note", "samsung,exynos4412", "samsung,exynos4"; + + /* this is the base variant without any kind of modem */ +}; diff --git a/arch/arm/boot/dts/exynos4412-p4note.dtsi b/arch/arm/boot/dts/exynos4412-p4note.dtsi new file mode 100644 index 000000000000..15b6acbbecb2 --- /dev/null +++ b/arch/arm/boot/dts/exynos4412-p4note.dtsi @@ -0,0 +1,1128 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Samsung's Exynos4412 based p4note device family base DT + * + * Copyright (c) 2020 Martin Jücker <martin.juecker@gmail.com> + */ + +/dts-v1/; +#include "exynos4412.dtsi" +#include "exynos4412-ppmu-common.dtsi" + +#include <dt-bindings/clock/maxim,max77686.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/samsung.h> + +/ { + compatible = "samsung,p4note", "samsung,exynos4412", "samsung,exynos4"; + + memory@40000000 { + device_type = "memory"; + reg = <0x40000000 0x80000000>; + }; + + chosen { + stdout-path = &serial_2; + }; + + firmware@204f000 { + compatible = "samsung,secure-firmware"; + reg = <0x0204F000 0x1000>; + }; + + fixed-rate-clocks { + xxti { + compatible = "samsung,clock-xxti"; + clock-frequency = <0>; + }; + + xusbxti { + compatible = "samsung,clock-xusbxti"; + clock-frequency = <24000000>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys>; + + key-down { + gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + label = "volume down"; + debounce-interval = <10>; + }; + + key-up { + gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + label = "volume up"; + debounce-interval = <10>; + }; + + key-power { + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + label = "power"; + debounce-interval = <10>; + wakeup-source; + }; + }; + + voltage-regulator-1 { + compatible = "regulator-fixed"; + regulator-name = "TSP_LDO1"; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_reg_gpio_1>; + gpios = <&gpm4 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + voltage-regulator-2 { + compatible = "regulator-fixed"; + regulator-name = "TSP_LDO2"; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_reg_gpio_2>; + gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + voltage-regulator-3 { + compatible = "regulator-fixed"; + regulator-name = "TSP_LDO3"; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_reg_gpio_3>; + gpios = <&gpb 7 GPIO_ACTIVE_HIGH>; + startup-delay-us = <20000>; + enable-active-high; + regulator-always-on; + }; + + wlan_pwrseq: sdhci3-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&wifi_reset>; + pinctrl-names = "default"; + clocks = <&max77686 MAX77686_CLK_PMIC>; + clock-names = "ext_clock"; + }; + + i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + + magnetometer@c { + compatible = "asahi-kasei,ak8975"; + reg = <0x0c>; + pinctrl-0 = <&ak8975_irq>; + pinctrl-names = "default"; + interrupt-parent = <&gpm4>; + interrupts = <7 IRQ_TYPE_EDGE_RISING>; + }; + }; + + i2c-gpio-2 { + compatible = "i2c-gpio"; + sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + + fuel-gauge@36 { + compatible = "maxim,max17042"; + reg = <0x36>; + pinctrl-0 = <&fuel_alert_irq>; + pinctrl-names = "default"; + interrupt-parent = <&gpx2>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + maxim,rsns-microohm = <10000>; + maxim,over-heat-temp = <600>; + maxim,over-volt = <4300>; + }; + }; + + i2c-gpio-3 { + compatible = "i2c-gpio"; + sda-gpios = <&gpm4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpm4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <5>; + #address-cells = <1>; + #size-cells = <0>; + + adc@41 { + compatible = "st,stmpe811"; + reg = <0x41>; + pinctrl-0 = <&stmpe_adc_irq>; + pinctrl-names = "default"; + interrupt-parent = <&gpx0>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + irq-trigger = <0x1>; + st,adc-freq = <3>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,sample-time = <3>; + + stmpe_adc { + compatible = "st,stmpe-adc"; + #io-channel-cells = <1>; + st,norequest-mask = <0x2F>; + }; + }; + }; +}; + +&adc { + vdd-supply = <&ldo3_reg>; + /* not verified */ + status = "okay"; +}; + +&bus_dmc { + devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; + vdd-supply = <&buck1_reg>; + status = "okay"; +}; + +&bus_acp { + devfreq = <&bus_dmc>; + status = "okay"; +}; + +&bus_c2c { + devfreq = <&bus_dmc>; + status = "okay"; +}; + +&bus_leftbus { + devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; + vdd-supply = <&buck3_reg>; + status = "okay"; +}; + +&bus_rightbus { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_display { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_fsys { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_peri { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_mfc { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&cpu0 { + cpu0-supply = <&buck2_reg>; +}; + +&cpu_thermal { + cooling-maps { + map0 { + /* Corresponds to 800MHz at freq_table */ + cooling-device = <&cpu0 7 7>, <&cpu1 7 7>, <&cpu2 7 7>, <&cpu3 7 7>; + }; + map1 { + /* Corresponds to 200MHz at freq_table */ + cooling-device = <&cpu0 13 13>, <&cpu1 13 13>, <&cpu2 13 13>, <&cpu3 13 13>; + }; + }; +}; + +&exynos_usbphy { + status = "okay"; +}; + +&fimd { + pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>; + pinctrl-names = "default"; + status = "okay"; + + display-timings { + timing0 { + clock-frequency = <66666666>; + hactive = <1280>; + vactive = <800>; + hfront-porch = <18>; + hback-porch = <36>; + hsync-len = <16>; + vback-porch = <16>; + vfront-porch = <4>; + vsync-len = <3>; + hsync-active = <1>; + }; + }; +}; + +&gpu { + mali-supply = <&buck4_reg>; + status = "okay"; +}; + +&hsotg { + vusb_a-supply = <&ldo12_reg>; + dr_mode = "peripheral"; + status = "okay"; +}; + +&i2c_3 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <400000>; + pinctrl-0 = <&i2c3_bus>; + pinctrl-names = "default"; + status = "okay"; + + touchscreen@4a { + compatible = "atmel,maxtouch"; + reg = <0x4a>; + pinctrl-0 = <&tsp_rst &tsp_irq>; + pinctrl-names = "default"; + interrupt-parent = <&gpm2>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpm0 4 GPIO_ACTIVE_HIGH>; + }; +}; + +&i2c_7 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <400000>; + pinctrl-0 = <&i2c7_bus>; + pinctrl-names = "default"; + status = "okay"; + + max77686: pmic@9 { + compatible = "maxim,max77686"; + interrupt-parent = <&gpx0>; + interrupts = <7 IRQ_TYPE_NONE>; + pinctrl-0 = <&max77686_irq>; + pinctrl-names = "default"; + reg = <0x09>; + #clock-cells = <1>; + + voltage-regulators { + ldo1_reg: LDO1 { + regulator-name = "ldo1"; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "ldo2"; + regulator-always-on; + }; + + /* WM8994 audio */ + ldo3_reg: LDO3 { + regulator-name = "VCC_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + ldo4_reg: LDO4 { + regulator-name = "ldo4"; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + regulator-name = "VCC_1.8V_IO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo6_reg: LDO6 { + regulator-name = "ldo6"; + regulator-always-on; + }; + + ldo7_reg: LDO7 { + regulator-name = "ldo7"; + regulator-always-on; + }; + + /* CSI IP block */ + ldo8_reg: LDO8 { + regulator-name = "VMIPI_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + /* IR LED on/off */ + ldo9_reg: LDO9 { + regulator-name = "VLED_IC_1.9V"; + regulator-min-microvolt = <1950000>; + regulator-max-microvolt = <1950000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* CSI IP block */ + ldo10_reg: LDO10 { + regulator-name = "VMIPI_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + ldo11_reg: LDO11 { + regulator-name = "VABB1_1.9V"; + regulator-min-microvolt = <1950000>; + regulator-max-microvolt = <1950000>; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* USB OTG */ + ldo12_reg: LDO12 { + regulator-name = "VUOTG_3.0V"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + /* not connected */ + ldo13_reg: LDO13 { + regulator-name = "ldo13"; + }; + + ldo14_reg: LDO14 { + regulator-name = "VABB2_1.9V"; + regulator-min-microvolt = <1950000>; + regulator-max-microvolt = <1950000>; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo15_reg: LDO15 { + regulator-name = "ldo15"; + regulator-always-on; + }; + + ldo16_reg: LDO16 { + regulator-name = "ldo16"; + regulator-always-on; + }; + + /* not connected */ + ldo17_reg: LDO17 { + regulator-name = "ldo17"; + }; + + /* Camera ISX012 */ + ldo18_reg: LDO18 { + regulator-name = "CAM_IO_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* Camera S5K6A3 */ + ldo19_reg: LDO19 { + regulator-name = "VT_CORE_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* not connected */ + ldo20_reg: LDO20 { + regulator-name = "ldo20"; + }; + + /* MMC2 */ + ldo21_reg: LDO21 { + regulator-name = "VTF_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>; + }; + + /* not connected */ + ldo22_reg: LDO22 { + regulator-name = "ldo22"; + }; + + /* ADC */ + ldo23_reg: LDO23 { + regulator-name = "VDD_ADC_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* Camera S5K6A3 */ + ldo24_reg: LDO24 { + regulator-name = "CAM_A2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo25_reg: LDO25 { + regulator-name = "VLED_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* Camera ISX012 */ + ldo26_reg: LDO26 { + regulator-name = "3MP_AF_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_MIF"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "VDD_ARM"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "VDD_INT"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "VDD_G3D"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1075000>; + regulator-boot-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "buck5"; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "buck6"; + regulator-always-on; + }; + + buck7_reg: BUCK7 { + regulator-name = "buck7"; + regulator-always-on; + }; + + /* not connected */ + buck8_reg: BUCK8 { + regulator-name = "buck8"; + }; + + buck9_reg: BUCK9 { + regulator-name = "3MP_CORE_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&mshc_0 { + broken-cd; + non-removable; + card-detect-delay = <200>; + clock-frequency = <400000000>; + samsung,dw-mshc-ciu-div = <0>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; + pinctrl-names = "default"; + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + status = "okay"; +}; + +&pinctrl_0 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep0>; + + tsp_reg_gpio_2: tsp-reg-gpio-2 { + samsung,pins = "gpb-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + tsp_reg_gpio_3: tsp-reg-gpio-3 { + samsung,pins = "gpb-7"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + sleep0: sleep-states { + PIN_SLP(gpa0-0, INPUT, NONE); + PIN_SLP(gpa0-1, OUT0, NONE); + PIN_SLP(gpa0-2, INPUT, NONE); + PIN_SLP(gpa0-3, INPUT, UP); + PIN_SLP(gpa0-4, INPUT, NONE); + PIN_SLP(gpa0-5, INPUT, DOWN); + PIN_SLP(gpa0-6, INPUT, DOWN); + PIN_SLP(gpa0-7, INPUT, UP); + + PIN_SLP(gpa1-0, INPUT, DOWN); + PIN_SLP(gpa1-1, INPUT, DOWN); + PIN_SLP(gpa1-2, INPUT, DOWN); + PIN_SLP(gpa1-3, INPUT, DOWN); + PIN_SLP(gpa1-4, INPUT, DOWN); + PIN_SLP(gpa1-5, INPUT, DOWN); + + PIN_SLP(gpb-0, INPUT, NONE); + PIN_SLP(gpb-1, INPUT, NONE); + PIN_SLP(gpb-2, INPUT, NONE); + PIN_SLP(gpb-3, INPUT, NONE); + PIN_SLP(gpb-4, INPUT, DOWN); + PIN_SLP(gpb-5, INPUT, DOWN); + PIN_SLP(gpb-6, INPUT, DOWN); + PIN_SLP(gpb-7, INPUT, DOWN); + + PIN_SLP(gpc0-0, INPUT, DOWN); + PIN_SLP(gpc0-1, INPUT, DOWN); + PIN_SLP(gpc0-2, INPUT, DOWN); + PIN_SLP(gpc0-3, INPUT, DOWN); + PIN_SLP(gpc0-4, INPUT, DOWN); + + PIN_SLP(gpc1-0, INPUT, UP); + PIN_SLP(gpc1-1, PREV, NONE); + PIN_SLP(gpc1-2, INPUT, UP); + PIN_SLP(gpc1-3, INPUT, UP); + PIN_SLP(gpc1-4, INPUT, UP); + + PIN_SLP(gpd0-0, INPUT, DOWN); + PIN_SLP(gpd0-1, OUT0, NONE); + PIN_SLP(gpd0-2, INPUT, NONE); + PIN_SLP(gpd0-3, INPUT, NONE); + + PIN_SLP(gpd1-0, INPUT, DOWN); + PIN_SLP(gpd1-1, INPUT, DOWN); + PIN_SLP(gpd1-2, INPUT, NONE); + PIN_SLP(gpd1-3, INPUT, NONE); + + PIN_SLP(gpf0-0, OUT0, NONE); + PIN_SLP(gpf0-1, OUT0, NONE); + PIN_SLP(gpf0-2, OUT0, NONE); + PIN_SLP(gpf0-3, OUT0, NONE); + PIN_SLP(gpf0-4, OUT0, NONE); + PIN_SLP(gpf0-5, OUT0, NONE); + PIN_SLP(gpf0-6, OUT0, NONE); + PIN_SLP(gpf0-7, OUT0, NONE); + + PIN_SLP(gpf1-0, OUT0, NONE); + PIN_SLP(gpf1-1, OUT0, NONE); + PIN_SLP(gpf1-2, OUT0, NONE); + PIN_SLP(gpf1-3, OUT0, NONE); + PIN_SLP(gpf1-4, OUT0, NONE); + PIN_SLP(gpf1-5, OUT0, NONE); + PIN_SLP(gpf1-6, OUT0, NONE); + PIN_SLP(gpf1-7, OUT0, NONE); + + PIN_SLP(gpf2-0, OUT0, NONE); + PIN_SLP(gpf2-1, OUT0, NONE); + PIN_SLP(gpf2-2, OUT0, NONE); + PIN_SLP(gpf2-3, OUT0, NONE); + PIN_SLP(gpf2-4, OUT0, NONE); + PIN_SLP(gpf2-5, OUT0, NONE); + PIN_SLP(gpf2-6, OUT0, NONE); + PIN_SLP(gpf2-7, OUT0, NONE); + + PIN_SLP(gpf3-0, OUT0, NONE); + PIN_SLP(gpf3-1, OUT0, NONE); + PIN_SLP(gpf3-2, OUT0, NONE); + PIN_SLP(gpf3-3, OUT0, NONE); + PIN_SLP(gpf3-4, OUT0, NONE); + PIN_SLP(gpf3-5, OUT0, NONE); + + PIN_SLP(gpj0-0, INPUT, DOWN); + PIN_SLP(gpj0-1, INPUT, DOWN); + PIN_SLP(gpj0-2, INPUT, DOWN); + PIN_SLP(gpj0-3, PREV, NONE); + PIN_SLP(gpj0-4, PREV, NONE); + PIN_SLP(gpj0-5, OUT0, NONE); + PIN_SLP(gpj0-6, OUT0, NONE); + PIN_SLP(gpj0-7, OUT0, NONE); + + PIN_SLP(gpj1-0, OUT0, NONE); + PIN_SLP(gpj1-1, INPUT, DOWN); + PIN_SLP(gpj1-2, PREV, NONE); + PIN_SLP(gpj1-3, OUT0, NONE); + }; +}; + +&pinctrl_1 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep1>; + + sd3_wifi: sd3-wifi { + samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + bt_shutdown: bt-shutdown { + samsung,pins = "gpl0-6"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + uart_sel: uart-sel { + samsung,pins = "gpl2-7"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-val = <1>; + /* 0 = CP, 1 = AP (serial output) */ + }; + + tsp_rst: tsp-rst { + samsung,pins = "gpm0-4"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + tsp_irq: tsp-irq { + samsung,pins = "gpm2-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_F>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + wifi_reset: wifi-reset { + samsung,pins = "gpm3-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + tsp_reg_gpio_1: tsp-reg-gpio-1 { + samsung,pins = "gpm4-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + ak8975_irq: ak8975-irq { + samsung,pins = "gpm4-7"; + samsung,pin-function = <EXYNOS_PIN_FUNC_F>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; + + stmpe_adc_irq: stmpe-adc-irq { + samsung,pins = "gpx0-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + max77686_irq: max77686-irq { + samsung,pins = "gpx0-7"; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + gpio_keys: gpio-keys { + samsung,pins = "gpx2-2", "gpx2-7", "gpx3-3"; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + fuel_alert_irq: fuel-alert-irq { + samsung,pins = "gpx2-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + wifi_host_wake: wifi-host-wake { + samsung,pins = "gpx2-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_F>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; + + bt_host_wakeup: bt-host-wakeup { + samsung,pins = "gpx2-6"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + bt_device_wakeup: bt-device-wakeup { + samsung,pins = "gpx3-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + sdhci2_cd: sdhci2-cd { + samsung,pins = "gpx3-4"; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + sleep1: sleep-states { + PIN_SLP(gpk0-0, PREV, NONE); + PIN_SLP(gpk0-1, PREV, NONE); + PIN_SLP(gpk0-2, PREV, NONE); + PIN_SLP(gpk0-3, PREV, NONE); + PIN_SLP(gpk0-4, PREV, NONE); + PIN_SLP(gpk0-5, PREV, NONE); + PIN_SLP(gpk0-6, PREV, NONE); + + PIN_SLP(gpk1-0, INPUT, DOWN); + PIN_SLP(gpk1-1, INPUT, DOWN); + PIN_SLP(gpk1-2, INPUT, DOWN); + PIN_SLP(gpk1-3, PREV, NONE); + PIN_SLP(gpk1-4, PREV, NONE); + PIN_SLP(gpk1-5, PREV, NONE); + PIN_SLP(gpk1-6, PREV, NONE); + + PIN_SLP(gpk2-0, INPUT, DOWN); + PIN_SLP(gpk2-1, INPUT, DOWN); + PIN_SLP(gpk2-2, INPUT, DOWN); + PIN_SLP(gpk2-3, INPUT, DOWN); + PIN_SLP(gpk2-4, INPUT, DOWN); + PIN_SLP(gpk2-5, INPUT, DOWN); + PIN_SLP(gpk2-6, INPUT, DOWN); + + PIN_SLP(gpk3-0, OUT0, NONE); + PIN_SLP(gpk3-1, INPUT, NONE); + PIN_SLP(gpk3-2, INPUT, DOWN); + PIN_SLP(gpk3-3, INPUT, NONE); + PIN_SLP(gpk3-4, INPUT, NONE); + PIN_SLP(gpk3-5, INPUT, NONE); + PIN_SLP(gpk3-6, INPUT, NONE); + + PIN_SLP(gpl0-0, OUT0, NONE); + PIN_SLP(gpl0-1, INPUT, NONE); + PIN_SLP(gpl0-2, INPUT, NONE); + PIN_SLP(gpl0-3, INPUT, DOWN); + PIN_SLP(gpl0-4, PREV, NONE); + PIN_SLP(gpl0-6, PREV, NONE); + + PIN_SLP(gpl1-0, OUT0, NONE); + PIN_SLP(gpl1-1, OUT0, NONE); + + PIN_SLP(gpl2-0, INPUT, DOWN); + PIN_SLP(gpl2-1, INPUT, DOWN); + PIN_SLP(gpl2-2, INPUT, DOWN); + PIN_SLP(gpl2-3, INPUT, DOWN); + PIN_SLP(gpl2-4, OUT0, NONE); + PIN_SLP(gpl2-5, INPUT, DOWN); + PIN_SLP(gpl2-6, PREV, NONE); + PIN_SLP(gpl2-7, PREV, NONE); + + PIN_SLP(gpm0-0, PREV, NONE); + PIN_SLP(gpm0-1, OUT0, NONE); + PIN_SLP(gpm0-2, INPUT, DOWN); + PIN_SLP(gpm0-3, INPUT, NONE); + PIN_SLP(gpm0-4, OUT0, NONE); + PIN_SLP(gpm0-5, OUT0, NONE); + PIN_SLP(gpm0-6, INPUT, DOWN); + PIN_SLP(gpm0-7, OUT0, NONE); + + PIN_SLP(gpm1-0, INPUT, NONE); + PIN_SLP(gpm1-1, INPUT, NONE); + PIN_SLP(gpm1-2, INPUT, NONE); + PIN_SLP(gpm1-3, INPUT, NONE); + PIN_SLP(gpm1-4, INPUT, NONE); + PIN_SLP(gpm1-5, INPUT, NONE); + PIN_SLP(gpm1-6, INPUT, DOWN); + + PIN_SLP(gpm2-0, INPUT, NONE); + PIN_SLP(gpm2-1, INPUT, NONE); + PIN_SLP(gpm2-2, OUT0, NONE); + PIN_SLP(gpm2-3, OUT0, DOWN); + PIN_SLP(gpm2-4, INPUT, DOWN); + + PIN_SLP(gpm3-0, PREV, NONE); + PIN_SLP(gpm3-1, PREV, NONE); + PIN_SLP(gpm3-2, PREV, NONE); + PIN_SLP(gpm3-3, OUT1, NONE); + PIN_SLP(gpm3-4, OUT0, DOWN); + PIN_SLP(gpm3-5, PREV, NONE); + PIN_SLP(gpm3-6, PREV, NONE); + PIN_SLP(gpm3-7, OUT0, NONE); + + PIN_SLP(gpm4-0, INPUT, NONE); + PIN_SLP(gpm4-1, INPUT, NONE); + PIN_SLP(gpm4-2, INPUT, DOWN); + PIN_SLP(gpm4-3, INPUT, DOWN); + PIN_SLP(gpm4-4, PREV, NONE); + PIN_SLP(gpm4-5, OUT0, NONE); + PIN_SLP(gpm4-6, OUT0, NONE); + PIN_SLP(gpm4-7, INPUT, DOWN); + + PIN_SLP(gpy0-0, INPUT, DOWN); + PIN_SLP(gpy0-1, INPUT, DOWN); + PIN_SLP(gpy0-2, INPUT, NONE); + PIN_SLP(gpy0-3, INPUT, NONE); + PIN_SLP(gpy0-4, INPUT, NONE); + PIN_SLP(gpy0-5, INPUT, NONE); + + PIN_SLP(gpy1-0, INPUT, DOWN); + PIN_SLP(gpy1-1, INPUT, DOWN); + PIN_SLP(gpy1-2, INPUT, DOWN); + PIN_SLP(gpy1-3, INPUT, DOWN); + + PIN_SLP(gpy2-0, PREV, NONE); + PIN_SLP(gpy2-1, INPUT, DOWN); + PIN_SLP(gpy2-2, INPUT, NONE); + PIN_SLP(gpy2-3, INPUT, NONE); + PIN_SLP(gpy2-4, INPUT, NONE); + PIN_SLP(gpy2-5, INPUT, NONE); + + PIN_SLP(gpy3-0, INPUT, DOWN); + PIN_SLP(gpy3-1, INPUT, DOWN); + PIN_SLP(gpy3-2, INPUT, DOWN); + PIN_SLP(gpy3-3, INPUT, DOWN); + PIN_SLP(gpy3-4, INPUT, DOWN); + PIN_SLP(gpy3-5, INPUT, DOWN); + PIN_SLP(gpy3-6, INPUT, DOWN); + PIN_SLP(gpy3-7, INPUT, DOWN); + + PIN_SLP(gpy4-0, INPUT, DOWN); + PIN_SLP(gpy4-1, INPUT, DOWN); + PIN_SLP(gpy4-2, INPUT, DOWN); + PIN_SLP(gpy4-3, INPUT, DOWN); + PIN_SLP(gpy4-4, INPUT, DOWN); + PIN_SLP(gpy4-5, INPUT, DOWN); + PIN_SLP(gpy4-6, INPUT, DOWN); + PIN_SLP(gpy4-7, INPUT, DOWN); + + PIN_SLP(gpy5-0, INPUT, DOWN); + PIN_SLP(gpy5-1, INPUT, DOWN); + PIN_SLP(gpy5-2, INPUT, DOWN); + PIN_SLP(gpy5-3, INPUT, DOWN); + PIN_SLP(gpy5-4, INPUT, DOWN); + PIN_SLP(gpy5-5, INPUT, DOWN); + PIN_SLP(gpy5-6, INPUT, DOWN); + PIN_SLP(gpy5-7, INPUT, DOWN); + + PIN_SLP(gpy6-0, INPUT, DOWN); + PIN_SLP(gpy6-1, INPUT, DOWN); + PIN_SLP(gpy6-2, INPUT, DOWN); + PIN_SLP(gpy6-3, INPUT, DOWN); + PIN_SLP(gpy6-4, INPUT, DOWN); + PIN_SLP(gpy6-5, INPUT, DOWN); + PIN_SLP(gpy6-6, INPUT, DOWN); + PIN_SLP(gpy6-7, INPUT, DOWN); + }; +}; + +&pinctrl_2 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep2>; + + sleep2: sleep-states { + PIN_SLP(gpz-0, INPUT, DOWN); + PIN_SLP(gpz-1, INPUT, DOWN); + PIN_SLP(gpz-2, INPUT, DOWN); + PIN_SLP(gpz-3, INPUT, DOWN); + PIN_SLP(gpz-4, INPUT, DOWN); + PIN_SLP(gpz-5, INPUT, DOWN); + PIN_SLP(gpz-6, INPUT, DOWN); + }; +}; + +&pinctrl_3 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep3>; + + sleep3: sleep-states { + PIN_SLP(gpv0-0, INPUT, DOWN); + PIN_SLP(gpv0-1, INPUT, DOWN); + PIN_SLP(gpv0-2, INPUT, DOWN); + PIN_SLP(gpv0-3, INPUT, DOWN); + PIN_SLP(gpv0-4, INPUT, DOWN); + PIN_SLP(gpv0-5, INPUT, DOWN); + PIN_SLP(gpv0-6, INPUT, DOWN); + PIN_SLP(gpv0-7, INPUT, DOWN); + + PIN_SLP(gpv1-0, INPUT, DOWN); + PIN_SLP(gpv1-1, INPUT, DOWN); + PIN_SLP(gpv1-2, INPUT, DOWN); + PIN_SLP(gpv1-3, INPUT, DOWN); + PIN_SLP(gpv1-4, INPUT, DOWN); + PIN_SLP(gpv1-5, INPUT, DOWN); + PIN_SLP(gpv1-6, INPUT, DOWN); + PIN_SLP(gpv1-7, INPUT, DOWN); + + PIN_SLP(gpv2-0, INPUT, DOWN); + PIN_SLP(gpv2-1, INPUT, DOWN); + PIN_SLP(gpv2-2, INPUT, DOWN); + PIN_SLP(gpv2-3, INPUT, DOWN); + PIN_SLP(gpv2-4, INPUT, DOWN); + PIN_SLP(gpv2-5, INPUT, DOWN); + PIN_SLP(gpv2-6, INPUT, DOWN); + PIN_SLP(gpv2-7, INPUT, DOWN); + + PIN_SLP(gpv3-0, INPUT, DOWN); + PIN_SLP(gpv3-1, INPUT, DOWN); + PIN_SLP(gpv3-2, INPUT, DOWN); + PIN_SLP(gpv3-3, INPUT, DOWN); + PIN_SLP(gpv3-4, INPUT, DOWN); + PIN_SLP(gpv3-5, INPUT, DOWN); + PIN_SLP(gpv3-6, INPUT, DOWN); + PIN_SLP(gpv3-7, INPUT, DOWN); + + PIN_SLP(gpv4-0, INPUT, DOWN); + PIN_SLP(gpv4-1, INPUT, DOWN); + }; +}; + +&pmu_system_controller { + assigned-clocks = <&pmu_system_controller 0>; + assigned-clock-parents = <&clock CLK_XUSBXTI>; +}; + +&rtc { + clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; + clock-names = "rtc", "rtc_src"; + status = "okay"; +}; + +&sdhci_2 { + bus-width = <4>; + cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; + pinctrl-names = "default"; + vmmc-supply = <&ldo21_reg>; + status = "okay"; +}; + +&sdhci_3 { + #address-cells = <1>; + #size-cells = <0>; + non-removable; + bus-width = <4>; + mmc-pwrseq = <&wlan_pwrseq>; + + pinctrl-names = "default"; + pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_wifi>; + status = "okay"; + + wifi@1 { + compatible = "brcm,bcm4329-fmac"; + reg = <0x1>; + pinctrl-names = "default"; + pinctrl-0 = <&wifi_host_wake>; + interrupt-parent = <&gpx2>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host-wake"; + }; +}; + +&serial_0 { + pinctrl-0 = <&uart0_data &uart0_fctl>; + pinctrl-names = "default"; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>; + pinctrl-names = "default"; + + max-speed = <2000000>; + shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>; + device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>; + clocks = <&max77686 MAX77686_CLK_PMIC>; + clock-names = "lpo"; + }; +}; + +&serial_2 { + pinctrl-0 = <&uart_sel>; + pinctrl-names = "default"; + status = "okay"; +}; + +&tmu { + status = "okay"; +};

[2/5] ARM: dts: add Samsung's exynos4412-based p4note boards

Commit Message

Comments

Patch