@@ -2117,6 +2117,7 @@ L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Supported
T: git git://github.com/microchip-ung/linux-upstream.git
F: arch/arm64/boot/dts/microchip/
+F: drivers/pinctrl/pinctrl-microchip-sgpio.c
N: sparx5
ARM/MIOA701 MACHINE SUPPORT
@@ -374,6 +374,22 @@ config PINCTRL_OCELOT
select OF_GPIO
select REGMAP_MMIO
+config PINCTRL_MICROCHIP_SGPIO
+ bool "Pinctrl driver for Microsemi/Microchip Serial GPIO"
+ depends on HAS_IOMEM
+ select GPIOLIB
+ select GENERIC_PINCONF
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
+ help
+ Support for the serial GPIO interface used on Microsemi and
+ Microchip SoC's. By using a serial interface, the SIO
+ controller significantly extends the number of available
+ GPIOs with a minimum number of additional pins on the
+ device. The primary purpose of the SIO controller is to
+ connect control signals from SFP modules and to act as an
+ LED controller.
+
source "drivers/pinctrl/actions/Kconfig"
source "drivers/pinctrl/aspeed/Kconfig"
source "drivers/pinctrl/bcm/Kconfig"
@@ -46,6 +46,7 @@ obj-$(CONFIG_PINCTRL_ZYNQ) += pinctrl-zynq.o
obj-$(CONFIG_PINCTRL_INGENIC) += pinctrl-ingenic.o
obj-$(CONFIG_PINCTRL_RK805) += pinctrl-rk805.o
obj-$(CONFIG_PINCTRL_OCELOT) += pinctrl-ocelot.o
+obj-$(CONFIG_PINCTRL_MICROCHIP_SGPIO) += pinctrl-microchip-sgpio.o
obj-$(CONFIG_PINCTRL_EQUILIBRIUM) += pinctrl-equilibrium.o
obj-y += actions/
new file mode 100644
@@ -0,0 +1,707 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Microsemi/Microchip SoCs serial gpio driver
+ *
+ * Author: <lars.povlsen@microchip.com>
+ *
+ * Copyright (c) 2020 Microchip Technology Inc. and its subsidiaries.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/gpio/driver.h>
+#include <linux/io.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+
+#include "core.h"
+#include "pinconf.h"
+
+#define SGPIO_BITS_PER_WORD 32
+#define SGPIO_MAX_BITS 4
+#define SGPIO_SRC_BITS 3 /* 3 bit wide field per pin */
+
+enum {
+ REG_INPUT_DATA,
+ REG_PORT_CONFIG,
+ REG_PORT_ENABLE,
+ REG_SIO_CONFIG,
+ REG_SIO_CLOCK,
+ MAXREG
+};
+
+enum {
+ SGPIO_ARCH_LUTON,
+ SGPIO_ARCH_OCELOT,
+ SGPIO_ARCH_SPARX5,
+};
+
+struct sgpio_properties {
+ int arch;
+ u8 regoff[MAXREG];
+};
+
+#define SGPIO_LUTON_AUTO_REPEAT BIT(5)
+#define SGPIO_LUTON_PORT_WIDTH GENMASK(3, 2)
+#define SGPIO_LUTON_CLK_FREQ GENMASK(11, 0)
+#define SGPIO_LUTON_BIT_SOURCE GENMASK(11, 0)
+
+#define SGPIO_OCELOT_AUTO_REPEAT BIT(10)
+#define SGPIO_OCELOT_PORT_WIDTH GENMASK(8, 7)
+#define SGPIO_OCELOT_CLK_FREQ GENMASK(19, 8)
+#define SGPIO_OCELOT_BIT_SOURCE GENMASK(23, 12)
+
+#define SGPIO_SPARX5_AUTO_REPEAT BIT(6)
+#define SGPIO_SPARX5_PORT_WIDTH GENMASK(4, 3)
+#define SGPIO_SPARX5_CLK_FREQ GENMASK(19, 8)
+#define SGPIO_SPARX5_BIT_SOURCE GENMASK(23, 12)
+
+const struct sgpio_properties properties_luton = {
+ .arch = SGPIO_ARCH_LUTON,
+ .regoff = { 0x00, 0x09, 0x29, 0x2a, 0x2b },
+};
+
+const struct sgpio_properties properties_ocelot = {
+ .arch = SGPIO_ARCH_OCELOT,
+ .regoff = { 0x00, 0x06, 0x26, 0x04, 0x05 },
+};
+
+const struct sgpio_properties properties_sparx5 = {
+ .arch = SGPIO_ARCH_SPARX5,
+ .regoff = { 0x00, 0x06, 0x26, 0x04, 0x05 },
+};
+
+static const char * const functions[] = { "gpio" };
+
+struct sgpio_bank {
+ struct sgpio_priv *priv;
+ bool is_input;
+ struct gpio_chip gpio;
+ struct pinctrl_desc pctl_desc;
+};
+
+struct sgpio_priv {
+ struct device *dev;
+ struct sgpio_bank in;
+ struct sgpio_bank out;
+ u32 bitcount;
+ u32 ports;
+ u32 clock;
+ u32 __iomem *regs;
+ const struct sgpio_properties *properties;
+};
+
+struct sgpio_port_addr {
+ u8 port;
+ u8 bit;
+};
+
+static inline void sgpio_pin_to_addr(struct sgpio_priv *priv, int pin,
+ struct sgpio_port_addr *addr)
+{
+ addr->port = pin / priv->bitcount;
+ addr->bit = pin % priv->bitcount;
+}
+
+static inline u32 sgpio_readl(struct sgpio_priv *priv, u32 rno, u32 off)
+{
+ u32 __iomem *reg = &priv->regs[priv->properties->regoff[rno] + off];
+
+ return readl(reg);
+}
+
+static inline void sgpio_writel(struct sgpio_priv *priv,
+ u32 val, u32 rno, u32 off)
+{
+ u32 __iomem *reg = &priv->regs[priv->properties->regoff[rno] + off];
+
+ writel(val, reg);
+}
+
+static inline void sgpio_clrsetbits(struct sgpio_priv *priv,
+ u32 rno, u32 off, u32 clear, u32 set)
+{
+ u32 __iomem *reg = &priv->regs[priv->properties->regoff[rno] + off];
+ u32 val = readl(reg);
+
+ val &= ~clear;
+ val |= set;
+
+ writel(val, reg);
+}
+
+static inline void sgpio_configure_bitstream(struct sgpio_priv *priv)
+{
+ int width = priv->bitcount - 1;
+ u32 clr, set;
+
+ switch (priv->properties->arch) {
+ case SGPIO_ARCH_LUTON:
+ clr = SGPIO_LUTON_PORT_WIDTH;
+ set = SGPIO_LUTON_AUTO_REPEAT |
+ FIELD_PREP(SGPIO_LUTON_PORT_WIDTH, width);
+ break;
+ case SGPIO_ARCH_OCELOT:
+ clr = SGPIO_OCELOT_PORT_WIDTH;
+ set = SGPIO_OCELOT_AUTO_REPEAT |
+ FIELD_PREP(SGPIO_OCELOT_PORT_WIDTH, width);
+ break;
+ case SGPIO_ARCH_SPARX5:
+ clr = SGPIO_SPARX5_PORT_WIDTH;
+ set = SGPIO_SPARX5_AUTO_REPEAT |
+ FIELD_PREP(SGPIO_SPARX5_PORT_WIDTH, width);
+ break;
+ default:
+ return;
+ }
+ sgpio_clrsetbits(priv, REG_SIO_CONFIG, 0, clr, set);
+}
+
+static inline void sgpio_configure_clock(struct sgpio_priv *priv, u32 clkfrq)
+{
+ u32 clr, set;
+
+ switch (priv->properties->arch) {
+ case SGPIO_ARCH_LUTON:
+ clr = SGPIO_LUTON_CLK_FREQ;
+ set = FIELD_PREP(SGPIO_LUTON_CLK_FREQ, clkfrq);
+ break;
+ case SGPIO_ARCH_OCELOT:
+ clr = SGPIO_OCELOT_CLK_FREQ;
+ set = FIELD_PREP(SGPIO_OCELOT_CLK_FREQ, clkfrq);
+ break;
+ case SGPIO_ARCH_SPARX5:
+ clr = SGPIO_SPARX5_CLK_FREQ;
+ set = FIELD_PREP(SGPIO_SPARX5_CLK_FREQ, clkfrq);
+ break;
+ default:
+ return;
+ }
+ sgpio_clrsetbits(priv, REG_SIO_CLOCK, 0, clr, set);
+}
+
+static void sgpio_output_set(struct sgpio_priv *priv,
+ struct sgpio_port_addr *addr,
+ int value)
+{
+ unsigned int bit = SGPIO_SRC_BITS * addr->bit;
+ u32 clr, set;
+
+ switch (priv->properties->arch) {
+ case SGPIO_ARCH_LUTON:
+ clr = FIELD_PREP(SGPIO_LUTON_BIT_SOURCE, BIT(bit));
+ set = FIELD_PREP(SGPIO_LUTON_BIT_SOURCE, value << bit);
+ break;
+ case SGPIO_ARCH_OCELOT:
+ clr = FIELD_PREP(SGPIO_OCELOT_BIT_SOURCE, BIT(bit));
+ set = FIELD_PREP(SGPIO_OCELOT_BIT_SOURCE, value << bit);
+ break;
+ case SGPIO_ARCH_SPARX5:
+ clr = FIELD_PREP(SGPIO_SPARX5_BIT_SOURCE, BIT(bit));
+ set = FIELD_PREP(SGPIO_SPARX5_BIT_SOURCE, value << bit);
+ break;
+ default:
+ return;
+ }
+ sgpio_clrsetbits(priv, REG_PORT_CONFIG, addr->port, clr, set);
+}
+
+static int sgpio_output_get(struct sgpio_priv *priv,
+ struct sgpio_port_addr *addr)
+{
+ u32 val, portval = sgpio_readl(priv, REG_PORT_CONFIG, addr->port);
+ unsigned int bit = SGPIO_SRC_BITS * addr->bit;
+
+ switch (priv->properties->arch) {
+ case SGPIO_ARCH_LUTON:
+ val = FIELD_GET(SGPIO_LUTON_BIT_SOURCE, portval);
+ break;
+ case SGPIO_ARCH_OCELOT:
+ val = FIELD_GET(SGPIO_OCELOT_BIT_SOURCE, portval);
+ break;
+ case SGPIO_ARCH_SPARX5:
+ val = FIELD_GET(SGPIO_SPARX5_BIT_SOURCE, portval);
+ break;
+ default:
+ val = 0;
+ }
+ return !!(val & BIT(bit));
+}
+
+static int sgpio_input_get(struct sgpio_priv *priv,
+ struct sgpio_port_addr *addr)
+{
+ return !!(sgpio_readl(priv, REG_INPUT_DATA, addr->bit) & BIT(addr->port));
+}
+
+static int sgpio_pinconf_get(struct pinctrl_dev *pctldev,
+ unsigned int pin, unsigned long *config)
+{
+ struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+ u32 param = pinconf_to_config_param(*config);
+ struct sgpio_priv *priv = bank->priv;
+ struct sgpio_port_addr addr;
+ int val;
+
+ sgpio_pin_to_addr(priv, pin, &addr);
+
+ switch (param) {
+ case PIN_CONFIG_INPUT_ENABLE:
+ val = bank->is_input;
+ break;
+
+ case PIN_CONFIG_OUTPUT_ENABLE:
+ val = !bank->is_input;
+ break;
+
+ case PIN_CONFIG_OUTPUT:
+ if (bank->is_input)
+ return -EINVAL;
+ val = sgpio_output_get(priv, &addr);
+ break;
+
+ default:
+ return -ENOTSUPP;
+ }
+
+ *config = pinconf_to_config_packed(param, val);
+
+ return 0;
+}
+
+static int sgpio_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+ unsigned long *configs, unsigned int num_configs)
+{
+ struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+ struct sgpio_priv *priv = bank->priv;
+ struct sgpio_port_addr addr;
+ int cfg, err = 0;
+ u32 param, arg;
+
+ sgpio_pin_to_addr(priv, pin, &addr);
+
+ for (cfg = 0; cfg < num_configs; cfg++) {
+ param = pinconf_to_config_param(configs[cfg]);
+ arg = pinconf_to_config_argument(configs[cfg]);
+
+ switch (param) {
+ case PIN_CONFIG_OUTPUT:
+ if (bank->is_input)
+ return -EINVAL;
+ sgpio_output_set(priv, &addr, arg);
+ break;
+
+ default:
+ err = -ENOTSUPP;
+ }
+ }
+
+ return err;
+}
+
+static const struct pinconf_ops sgpio_confops = {
+ .is_generic = true,
+ .pin_config_get = sgpio_pinconf_get,
+ .pin_config_set = sgpio_pinconf_set,
+ .pin_config_config_dbg_show = pinconf_generic_dump_config,
+};
+
+static int sgpio_get_functions_count(struct pinctrl_dev *pctldev)
+{
+ return 1;
+}
+
+static const char *sgpio_get_function_name(struct pinctrl_dev *pctldev,
+ unsigned int function)
+{
+ return functions[0];
+}
+
+static int sgpio_get_function_groups(struct pinctrl_dev *pctldev,
+ unsigned int function,
+ const char *const **groups,
+ unsigned *const num_groups)
+{
+ *groups = functions;
+ *num_groups = ARRAY_SIZE(functions);
+
+ return 0;
+}
+
+static int sgpio_pinmux_set_mux(struct pinctrl_dev *pctldev,
+ unsigned int selector, unsigned int group)
+{
+ return 0;
+}
+
+static int sgpio_gpio_set_direction(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int pin, bool input)
+{
+ struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+
+ return (input == bank->is_input) ? 0 : -EINVAL;
+}
+
+static int sgpio_gpio_request_enable(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int offset)
+{
+ struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+ struct sgpio_priv *priv = bank->priv;
+ struct sgpio_port_addr addr;
+
+ sgpio_pin_to_addr(priv, offset, &addr);
+
+ if ((priv->ports & BIT(addr.port)) == 0) {
+ dev_warn(priv->dev, "Request port %d.%d: Port is not enabled\n",
+ addr.port, addr.bit);
+ }
+
+ return 0;
+}
+
+static const struct pinmux_ops sgpio_pmx_ops = {
+ .get_functions_count = sgpio_get_functions_count,
+ .get_function_name = sgpio_get_function_name,
+ .get_function_groups = sgpio_get_function_groups,
+ .set_mux = sgpio_pinmux_set_mux,
+ .gpio_set_direction = sgpio_gpio_set_direction,
+ .gpio_request_enable = sgpio_gpio_request_enable,
+};
+
+static int sgpio_pctl_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+
+ return bank->pctl_desc.npins;
+}
+
+static const char *sgpio_pctl_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned int group)
+{
+ struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+
+ return bank->pctl_desc.pins[group].name;
+}
+
+static int sgpio_pctl_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned int group,
+ const unsigned int **pins,
+ unsigned int *num_pins)
+{
+ struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+
+ *pins = &bank->pctl_desc.pins[group].number;
+ *num_pins = 1;
+
+ return 0;
+}
+
+static const struct pinctrl_ops sgpio_pctl_ops = {
+ .get_groups_count = sgpio_pctl_get_groups_count,
+ .get_group_name = sgpio_pctl_get_group_name,
+ .get_group_pins = sgpio_pctl_get_group_pins,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
+ .dt_free_map = pinconf_generic_dt_free_map,
+};
+
+static int microchip_sgpio_direction_input(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct sgpio_bank *bank = gpiochip_get_data(gc);
+
+ /* Fixed-position function */
+ return bank->is_input ? 0 : -EINVAL;
+}
+
+static int microchip_sgpio_direction_output(struct gpio_chip *gc,
+ unsigned int gpio, int value)
+{
+ struct sgpio_bank *bank = gpiochip_get_data(gc);
+ struct sgpio_priv *priv = bank->priv;
+ struct sgpio_port_addr addr;
+
+ /* Fixed-position function */
+ if (bank->is_input)
+ return -EINVAL;
+
+ sgpio_pin_to_addr(priv, gpio, &addr);
+
+ sgpio_output_set(priv, &addr, value);
+
+ return 0;
+}
+
+static int microchip_sgpio_get_direction(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct sgpio_bank *bank = gpiochip_get_data(gc);
+
+ return bank->is_input ? GPIO_LINE_DIRECTION_IN : GPIO_LINE_DIRECTION_OUT;
+}
+
+static void microchip_sgpio_set_value(struct gpio_chip *gc,
+ unsigned int gpio, int value)
+{
+ microchip_sgpio_direction_output(gc, gpio, value);
+}
+
+static int microchip_sgpio_get_value(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct sgpio_bank *bank = gpiochip_get_data(gc);
+ struct sgpio_priv *priv = bank->priv;
+ struct sgpio_port_addr addr;
+
+ sgpio_pin_to_addr(priv, gpio, &addr);
+
+ return bank->is_input ? sgpio_input_get(priv, &addr) : sgpio_output_get(priv, &addr);
+}
+
+static int microchip_sgpio_of_xlate(struct gpio_chip *gc,
+ const struct of_phandle_args *gpiospec,
+ u32 *flags)
+{
+ struct sgpio_bank *bank = gpiochip_get_data(gc);
+ struct sgpio_priv *priv = bank->priv;
+ int pin;
+
+ /*
+ * Note that the SGIO pin is defined by *2* numbers, a port
+ * number between 0 and 31, and a bit index, 0 to 3.
+ */
+ if (gpiospec->args[0] > SGPIO_BITS_PER_WORD ||
+ gpiospec->args[1] > priv->bitcount)
+ return -EINVAL;
+
+ pin = gpiospec->args[1] + gpiospec->args[0] * priv->bitcount;
+
+ if (pin > gc->ngpio)
+ return -EINVAL;
+
+ if (flags)
+ *flags = gpiospec->args[2];
+
+ return pin;
+}
+
+static int microchip_sgpio_get_ports(struct sgpio_priv *priv)
+{
+ const char *range_property_name = "microchip,sgpio-port-ranges";
+ struct device *dev = priv->dev;
+ u32 range_params[64];
+ int i, nranges, ret;
+
+ /* Calculate port mask */
+ nranges = device_property_count_u32(dev, range_property_name);
+ if (nranges < 2 || nranges % 2 || nranges > ARRAY_SIZE(range_params)) {
+ dev_err(dev, "%s port range: '%s' property\n",
+ nranges == -EINVAL ? "Missing" : "Invalid",
+ range_property_name);
+ return -EINVAL;
+ }
+
+ ret = device_property_read_u32_array(dev, range_property_name,
+ range_params, nranges);
+ if (ret) {
+ dev_err(dev, "failed to parse '%s' property: %d\n",
+ range_property_name, ret);
+ return ret;
+ }
+ for (i = 0; i < nranges; i += 2) {
+ int start, end;
+
+ start = range_params[i];
+ end = range_params[i + 1];
+ if (start > end || end >= SGPIO_BITS_PER_WORD) {
+ dev_err(dev, "Ill-formed port-range [%d:%d]\n",
+ start, end);
+ }
+ priv->ports |= GENMASK(end, start);
+ }
+
+ return 0;
+}
+
+static int microchip_sgpio_register_bank(struct device *dev,
+ struct sgpio_priv *priv,
+ struct fwnode_handle *fwnode,
+ int bankno)
+{
+ struct pinctrl_pin_desc *pins;
+ struct pinctrl_desc *pctl_desc;
+ struct pinctrl_dev *pctldev;
+ struct sgpio_bank *bank;
+ struct gpio_chip *gc;
+ u32 ngpios;
+ int i, ret;
+
+ /* Get overall bank struct */
+ bank = (bankno == 0) ? &priv->in : &priv->out;
+ bank->priv = priv;
+
+ if (fwnode_property_read_u32(fwnode, "ngpios", &ngpios)) {
+ dev_info(dev, "failed to get number of gpios for bank%d\n",
+ bankno);
+ ngpios = 64;
+ }
+
+ priv->bitcount = ngpios / SGPIO_BITS_PER_WORD;
+ if (priv->bitcount > SGPIO_MAX_BITS) {
+ dev_err(dev, "Bit width exceeds maximum (%d)\n",
+ SGPIO_MAX_BITS);
+ return -EINVAL;
+ }
+
+ pctl_desc = &bank->pctl_desc;
+ pctl_desc->name = devm_kasprintf(dev, GFP_KERNEL, "%s-%sput",
+ dev_name(dev),
+ bank->is_input ? "in" : "out");
+ pctl_desc->pctlops = &sgpio_pctl_ops;
+ pctl_desc->pmxops = &sgpio_pmx_ops;
+ pctl_desc->confops = &sgpio_confops;
+ pctl_desc->owner = THIS_MODULE;
+
+ pins = devm_kzalloc(dev, sizeof(*pins)*ngpios, GFP_KERNEL);
+ if (!pins)
+ return -ENOMEM;
+
+ pctl_desc->npins = ngpios;
+ pctl_desc->pins = pins;
+
+ for (i = 0; i < ngpios; i++) {
+ struct sgpio_port_addr addr;
+
+ sgpio_pin_to_addr(priv, i, &addr);
+
+ pins[i].number = i;
+ pins[i].name = devm_kasprintf(dev, GFP_KERNEL,
+ "SGPIO_%c_p%db%d",
+ bank->is_input ? 'I' : 'O',
+ addr.port, addr.bit);
+ if (!pins[i].name)
+ return -ENOMEM;
+ }
+
+ pctldev = devm_pinctrl_register(dev, pctl_desc, bank);
+ if (IS_ERR(pctldev))
+ return dev_err_probe(dev, PTR_ERR(pctldev), "Failed to register pinctrl\n");
+
+ gc = &bank->gpio;
+ gc->label = pctl_desc->name;
+ gc->parent = dev;
+ gc->of_node = to_of_node(fwnode);
+ gc->owner = THIS_MODULE;
+ gc->get_direction = microchip_sgpio_get_direction;
+ gc->direction_input = microchip_sgpio_direction_input;
+ gc->direction_output = microchip_sgpio_direction_output;
+ gc->get = microchip_sgpio_get_value;
+ gc->set = microchip_sgpio_set_value;
+ gc->request = gpiochip_generic_request;
+ gc->free = gpiochip_generic_free;
+ gc->of_xlate = microchip_sgpio_of_xlate;
+ gc->of_gpio_n_cells = 3;
+ gc->base = -1;
+ gc->ngpio = ngpios;
+
+ ret = devm_gpiochip_add_data(dev, gc, bank);
+ if (ret)
+ dev_err(dev, "Failed to register: ret %d\n", ret);
+
+ return ret;
+}
+
+static int microchip_sgpio_probe(struct platform_device *pdev)
+{
+ int div_clock = 0, ret, port, i, nbanks;
+ struct device *dev = &pdev->dev;
+ struct fwnode_handle *fwnode;
+ struct sgpio_priv *priv;
+ struct clk *clk;
+ u32 val;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->dev = dev;
+
+ clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(clk))
+ return dev_err_probe(dev, PTR_ERR(clk), "Failed to get clock\n");
+
+ div_clock = clk_get_rate(clk);
+ if (device_property_read_u32(dev, "bus-frequency", &priv->clock))
+ priv->clock = 12500000;
+ if (priv->clock == 0 || priv->clock > (div_clock / 2)) {
+ dev_err(dev, "Invalid frequency %d\n", priv->clock);
+ return -EINVAL;
+ }
+
+ priv->regs = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(priv->regs))
+ return PTR_ERR(priv->regs);
+ priv->properties = device_get_match_data(dev);
+ priv->in.is_input = true;
+
+ /* Get rest of device properties */
+ ret = microchip_sgpio_get_ports(priv);
+ if (ret)
+ return ret;
+
+ nbanks = device_get_child_node_count(dev);
+ if (nbanks != 2) {
+ dev_err(dev, "Must have 2 banks (have %d)\n", nbanks);
+ return -EINVAL;
+ }
+
+ i = 0;
+ device_for_each_child_node(dev, fwnode) {
+ ret = microchip_sgpio_register_bank(dev, priv, fwnode, i++);
+ if (ret)
+ return ret;
+ }
+
+ if (priv->in.gpio.ngpio != priv->out.gpio.ngpio) {
+ dev_err(dev, "Banks must have same GPIO count\n");
+ return -EINVAL;
+ }
+
+ sgpio_configure_bitstream(priv);
+
+ val = max(2U, div_clock / priv->clock);
+ sgpio_configure_clock(priv, val);
+
+ for (port = 0; port < SGPIO_BITS_PER_WORD; port++)
+ sgpio_writel(priv, 0, REG_PORT_CONFIG, port);
+ sgpio_writel(priv, priv->ports, REG_PORT_ENABLE, 0);
+
+ return 0;
+}
+
+static const struct of_device_id microchip_sgpio_gpio_of_match[] = {
+ {
+ .compatible = "microchip,sparx5-sgpio",
+ .data = &properties_sparx5,
+ }, {
+ .compatible = "mscc,luton-sgpio",
+ .data = &properties_luton,
+ }, {
+ .compatible = "mscc,ocelot-sgpio",
+ .data = &properties_ocelot,
+ }, {
+ /* sentinel */
+ }
+};
+
+static struct platform_driver microchip_sgpio_pinctrl_driver = {
+ .driver = {
+ .name = "pinctrl-microchip-sgpio",
+ .of_match_table = microchip_sgpio_gpio_of_match,
+ .suppress_bind_attrs = true,
+ },
+ .probe = microchip_sgpio_probe,
+};
+builtin_platform_driver(microchip_sgpio_pinctrl_driver);
This adds a pinctrl driver for the Microsemi/Microchip Serial GPIO (SGPIO) device used in various SoC's. The driver is added as a pinctrl driver, albeit only having just GPIO support currently. The hardware supports other functions that will be added following. Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com> --- MAINTAINERS | 1 + drivers/pinctrl/Kconfig | 16 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-microchip-sgpio.c | 707 ++++++++++++++++++++++ 4 files changed, 725 insertions(+) create mode 100644 drivers/pinctrl/pinctrl-microchip-sgpio.c