| Message ID | 20201111130754.2283993-1-linus.walleij@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v2] dt-bindings: display: mcde: Convert to YAML schema | expand |
Hi Linus. A few comments when I read through this. Sam On Wed, Nov 11, 2020 at 02:07:54PM +0100, Linus Walleij wrote: > This moves the MCDE bindings over to using the YAML schema > to describe the ST-Ericsson MCDE display controller, > making use of the generic DSI controller schema. > > We also add the "port" node, we will use this when adding > LCD panels using the direct parallel interface DPI instead > of DSI. > > Cc: devicetree@vger.kernel.org > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> > --- > ChangeLog v1->v2: > - Cut the description on the interrupts. > - Drop maxItems: 3 on clocks and clock-names: implicit from > the number of listed items. > - Tag the DSI ports with unevaluatedProperties: false > - Tag the MCDE as such with additionalProperties: true > - It was a bit hard to test this because of the code base > being out of phase with the validation tools but it seems > to check out. > --- > .../devicetree/bindings/display/ste,mcde.txt | 104 ----------- > .../devicetree/bindings/display/ste,mcde.yaml | 166 ++++++++++++++++++ > 2 files changed, 166 insertions(+), 104 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/display/ste,mcde.txt > create mode 100644 Documentation/devicetree/bindings/display/ste,mcde.yaml > > diff --git a/Documentation/devicetree/bindings/display/ste,mcde.txt b/Documentation/devicetree/bindings/display/ste,mcde.txt > deleted file mode 100644 > index 4c33c692bd5f..000000000000 > --- a/Documentation/devicetree/bindings/display/ste,mcde.txt > +++ /dev/null > @@ -1,104 +0,0 @@ > -ST-Ericsson Multi Channel Display Engine MCDE > - > -The ST-Ericsson MCDE is a display controller with support for compositing > -and displaying several channels memory resident graphics data on DSI or > -LCD displays or bridges. It is used in the ST-Ericsson U8500 platform. > - > -Required properties: > - > -- compatible: must be: > - "ste,mcde" > -- reg: register base for the main MCDE control registers, should be > - 0x1000 in size > -- interrupts: the interrupt line for the MCDE > -- epod-supply: a phandle to the EPOD regulator > -- vana-supply: a phandle to the analog voltage regulator > -- clocks: an array of the MCDE clocks in this strict order: > - MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI > - (HDMI clock), DSI0ESCLK (DSI0 energy save clock), > - DSI1ESCLK (DSI1 energy save clock), DSI2ESCLK (DSI2 energy > - save clock) I did not find these two clocks in the binding below. > -- clock-names: must be the following array: > - "mcde", "lcd", "hdmi" > - to match the required clock inputs above. > -- #address-cells: should be <1> (for the DSI hosts that will be children) > -- #size-cells: should be <1> (for the DSI hosts that will be children) > -- ranges: this should always be stated > - > -Required subnodes: > - > -The devicetree must specify subnodes for the DSI host adapters. > -These must have the following characteristics: > - > -- compatible: must be: > - "ste,mcde-dsi" > -- reg: must specify the register range for the DSI host > -- vana-supply: phandle to the VANA voltage regulator > -- clocks: phandles to the high speed and low power (energy save) clocks > - the high speed clock is not present on the third (dsi2) block, so it > - should only have the "lp" clock > -- clock-names: "hs" for the high speed clock and "lp" for the low power > - (energy save) clock > -- #address-cells: should be <1> > -- #size-cells: should be <0> > - > -Display panels and bridges will appear as children on the DSI hosts, and > -the displays are connected to the DSI hosts using the common binding > -for video transmitter interfaces; see > -Documentation/devicetree/bindings/media/video-interfaces.txt > - > -If a DSI host is unused (not connected) it will have no children defined. > - > -Example: > - > -mcde@a0350000 { > - compatible = "ste,mcde"; > - reg = <0xa0350000 0x1000>; > - interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; > - epod-supply = <&db8500_b2r2_mcde_reg>; > - vana-supply = <&ab8500_ldo_ana_reg>; > - clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */ > - <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */ > - <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */ > - clock-names = "mcde", "lcd", "hdmi"; > - #address-cells = <1>; > - #size-cells = <1>; > - ranges; > - > - dsi0: dsi@a0351000 { > - compatible = "ste,mcde-dsi"; > - reg = <0xa0351000 0x1000>; > - vana-supply = <&ab8500_ldo_ana_reg>; > - clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>; > - clock-names = "hs", "lp"; > - #address-cells = <1>; > - #size-cells = <0>; > - > - panel { > - compatible = "samsung,s6d16d0"; > - reg = <0>; > - vdd1-supply = <&ab8500_ldo_aux1_reg>; > - reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; > - }; > - > - }; > - dsi1: dsi@a0352000 { > - compatible = "ste,mcde-dsi"; > - reg = <0xa0352000 0x1000>; > - vana-supply = <&ab8500_ldo_ana_reg>; > - clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>; > - clock-names = "hs", "lp"; > - #address-cells = <1>; > - #size-cells = <0>; > - }; > - dsi2: dsi@a0353000 { > - compatible = "ste,mcde-dsi"; > - reg = <0xa0353000 0x1000>; > - vana-supply = <&ab8500_ldo_ana_reg>; > - /* This DSI port only has the Low Power / Energy Save clock */ > - clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>; > - clock-names = "lp"; > - #address-cells = <1>; > - #size-cells = <0>; > - }; > -}; > diff --git a/Documentation/devicetree/bindings/display/ste,mcde.yaml b/Documentation/devicetree/bindings/display/ste,mcde.yaml > new file mode 100644 > index 000000000000..51851566c72d > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/ste,mcde.yaml > @@ -0,0 +1,166 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/display/ste,mcde.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: ST-Ericsson Multi Channel Display Engine MCDE > + > +maintainers: > + - Linus Walleij <linus.walleij@linaro.org> > + > +properties: > + compatible: > + const: ste,mcde > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + clocks: > + description: an array of the MCDE clocks > + items: > + - description: MCDECLK (main MCDE clock) > + - description: LCDCLK (LCD clock) > + - description: PLLDSI (HDMI clock) > + > + clock-names: > + items: > + - const: mcde > + - const: lcd > + - const: hdmi > + > + epod-supply: > + description: a phandle to the EPOD regulator > + > + vana-supply: > + description: a phandle to the analog voltage regulator > + > + port: > + type: object > + description: > + A DPI port node with endpoint definitions as defined in > + Documentation/devicetree/bindings/media/video-interfaces.txt > + > + "#address-cells": > + const: 1 > + > + "#size-cells": > + const: 1 > + > + ranges: true > + This is a transition from .txt to DT Schema so OK with this sub-node. But otherwise the dsi node should have been linked using graph nodes. So OK - just thinking out loud. > +patternProperties: > + "^dsi@[0-9a-f]+$": > + description: subnodes for the three DSI host adapters > + type: object > + allOf: > + - $ref: dsi-controller.yaml# > + properties: > + compatible: > + const: ste,mcde-dsi > + > + reg: > + maxItems: 1 > + > + vana-supply: > + description: a phandle to the analog voltage regulator > + > + clocks: > + description: phandles to the high speed and low power (energy save) clocks > + the high speed clock is not present on the third (dsi2) block, so it > + should only have the "lp" clock > + minItems: 1 > + maxItems: 2 > + > + clock-names: > + oneOf: > + - items: > + - const: hs > + - const: lp > + - items: > + - const: lp > + The dsi nodes needs the #address-cells and #size-cells - at least if a panel node is specified. > + required: > + - compatible > + - reg > + - vana-supply > + - clocks > + - clock-names > + > + unevaluatedProperties: false > + > +required: > + - compatible > + - reg > + - interrupts > + - clocks > + - clock-names > + - epod-supply > + - vana-supply > + > +additionalProperties: true Why are additional properties allowed here? > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/irq.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/mfd/dbx500-prcmu.h> > + #include <dt-bindings/gpio/gpio.h> > + > + mcde@a0350000 { > + compatible = "ste,mcde"; > + reg = <0xa0350000 0x1000>; > + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; > + epod-supply = <&db8500_b2r2_mcde_reg>; > + vana-supply = <&ab8500_ldo_ana_reg>; > + clocks = <&prcmu_clk PRCMU_MCDECLK>, > + <&prcmu_clk PRCMU_LCDCLK>, > + <&prcmu_clk PRCMU_PLLDSI>; > + clock-names = "mcde", "lcd", "hdmi"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + dsi0: dsi@a0351000 { > + compatible = "ste,mcde-dsi"; > + reg = <0xa0351000 0x1000>; > + vana-supply = <&ab8500_ldo_ana_reg>; > + clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>; > + clock-names = "hs", "lp"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + panel@0 { > + compatible = "samsung,s6d16d0"; > + reg = <0>; > + vdd1-supply = <&ab8500_ldo_aux1_reg>; > + reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + dsi1: dsi@a0352000 { > + compatible = "ste,mcde-dsi"; > + reg = <0xa0352000 0x1000>; > + vana-supply = <&ab8500_ldo_ana_reg>; > + clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>; > + clock-names = "hs", "lp"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + dsi2: dsi@a0353000 { > + compatible = "ste,mcde-dsi"; > + reg = <0xa0353000 0x1000>; > + vana-supply = <&ab8500_ldo_ana_reg>; > + /* This DSI port only has the Low Power / Energy Save clock */ > + clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>; > + clock-names = "lp"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + > +... > -- > 2.26.2 > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel
On Wed, Nov 11, 2020 at 9:59 PM Sam Ravnborg <sam@ravnborg.org> wrote: > On Wed, Nov 11, 2020 at 02:07:54PM +0100, Linus Walleij wrote: > > -- clocks: an array of the MCDE clocks in this strict order: > > - MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI > > - (HDMI clock), DSI0ESCLK (DSI0 energy save clock), > > > - DSI1ESCLK (DSI1 energy save clock), DSI2ESCLK (DSI2 energy > > - save clock) > > I did not find these two clocks in the binding below. The old bindings are wrong. These clocks belong on the DSI host adapters, so they are in this part of the binding: + clocks: + description: phandles to the high speed and low power (energy save) clocks + the high speed clock is not present on the third (dsi2) block, so it + should only have the "lp" clock + minItems: 1 + maxItems: 2 + + clock-names: + oneOf: + - items: + - const: hs + - const: lp + - items: + - const: lp All device trees have these in the right place, we just didn't notice that the bindings were wrong exactly because we weren't using formal YAML syntax. Now the strictness of this parser makes me fix my bugs... > > + port: > > + type: object > > + description: > > + A DPI port node with endpoint definitions as defined in > > + Documentation/devicetree/bindings/media/video-interfaces.txt > > + > > + "#address-cells": > > + const: 1 > > + > > + "#size-cells": > > + const: 1 > > + > > + ranges: true > > This is a transition from .txt to DT Schema so OK with this sub-node. > But otherwise the dsi node should have been linked using graph nodes. > So OK - just thinking out loud. Actually when I introduced the MCDE DSI last year at first I used port and graphs: https://lore.kernel.org/dri-devel/20190207083647.20615-3-linus.walleij@linaro.org/ Then Rob asked "why?": https://lore.kernel.org/dri-devel/20190225223124.GA29057@bogus/ And then I removed it, as having a panel directly under a DSI host is fine. > > +patternProperties: > > + "^dsi@[0-9a-f]+$": > > + description: subnodes for the three DSI host adapters > > + type: object > > + allOf: > > + - $ref: dsi-controller.yaml# (...) > The dsi nodes needs the #address-cells and #size-cells - at least if a > panel node is specified. This is specified in the referenced schema dsi-controller.yaml. > > +required: > > + - compatible > > + - reg > > + - interrupts > > + - clocks > > + - clock-names > > + - epod-supply > > + - vana-supply > > + > > +additionalProperties: true > > Why are additional properties allowed here? It's because the SoC peripherals have things like pin control (currently handled by a quirk in the YAML validator I think) and resets is something else I will likely add at some point, and then this would result in warnings unless I lock-step changes in the schema and DTS files. I *can* disallow this if you insist. Yours. Linus Walleij
On Thu, Nov 12, 2020 at 01:19:34PM +0100, Linus Walleij wrote: > On Wed, Nov 11, 2020 at 9:59 PM Sam Ravnborg <sam@ravnborg.org> wrote: > > On Wed, Nov 11, 2020 at 02:07:54PM +0100, Linus Walleij wrote: > > > > -- clocks: an array of the MCDE clocks in this strict order: > > > - MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI > > > - (HDMI clock), DSI0ESCLK (DSI0 energy save clock), > > > > > - DSI1ESCLK (DSI1 energy save clock), DSI2ESCLK (DSI2 energy > > > - save clock) > > > > I did not find these two clocks in the binding below. > > The old bindings are wrong. These clocks belong on the DSI > host adapters, so they are in this part of the binding: Please include this info in the changelog to avoid confusing others. > > + clocks: > + description: phandles to the high speed and low power (energy > save) clocks > + the high speed clock is not present on the third (dsi2) block, so it > + should only have the "lp" clock > + minItems: 1 > + maxItems: 2 > + > + clock-names: > + oneOf: > + - items: > + - const: hs > + - const: lp > + - items: > + - const: lp > > All device trees have these in the right place, we just didn't notice that > the bindings were wrong exactly because we weren't using > formal YAML syntax. Now the strictness of this parser makes me > fix my bugs... > > > > + port: > > > + type: object > > > + description: > > > + A DPI port node with endpoint definitions as defined in > > > + Documentation/devicetree/bindings/media/video-interfaces.txt > > > + > > > + "#address-cells": > > > + const: 1 > > > + > > > + "#size-cells": > > > + const: 1 > > > + > > > + ranges: true > > > > This is a transition from .txt to DT Schema so OK with this sub-node. > > But otherwise the dsi node should have been linked using graph nodes. > > So OK - just thinking out loud. > > Actually when I introduced the MCDE DSI last year at first I used port > and graphs: > https://lore.kernel.org/dri-devel/20190207083647.20615-3-linus.walleij@linaro.org/ > Then Rob asked "why?": > https://lore.kernel.org/dri-devel/20190225223124.GA29057@bogus/ > And then I removed it, as having a panel directly under a > DSI host is fine. OK, thanks for the explanation. > > > > +patternProperties: > > > + "^dsi@[0-9a-f]+$": > > > + description: subnodes for the three DSI host adapters > > > + type: object > > > + allOf: > > > + - $ref: dsi-controller.yaml# > (...) > > The dsi nodes needs the #address-cells and #size-cells - at least if a > > panel node is specified. > > This is specified in the referenced schema dsi-controller.yaml. > > > > +required: > > > + - compatible > > > + - reg > > > + - interrupts > > > + - clocks > > > + - clock-names > > > + - epod-supply > > > + - vana-supply > > > + > > > +additionalProperties: true > > > > Why are additional properties allowed here? > > It's because the SoC peripherals have things like pin control > (currently handled by a quirk in the YAML validator I think) and > resets is something else I will likely add at some point, and then > this would result in warnings unless I lock-step changes in the > schema and DTS files. > > I *can* disallow this if you insist. Add reset now as an optional property and you are covered. The HW does not change, and this describes the HW and not the drivers. Sam
diff --git a/Documentation/devicetree/bindings/display/ste,mcde.txt b/Documentation/devicetree/bindings/display/ste,mcde.txt deleted file mode 100644 index 4c33c692bd5f..000000000000 --- a/Documentation/devicetree/bindings/display/ste,mcde.txt +++ /dev/null @@ -1,104 +0,0 @@ -ST-Ericsson Multi Channel Display Engine MCDE - -The ST-Ericsson MCDE is a display controller with support for compositing -and displaying several channels memory resident graphics data on DSI or -LCD displays or bridges. It is used in the ST-Ericsson U8500 platform. - -Required properties: - -- compatible: must be: - "ste,mcde" -- reg: register base for the main MCDE control registers, should be - 0x1000 in size -- interrupts: the interrupt line for the MCDE -- epod-supply: a phandle to the EPOD regulator -- vana-supply: a phandle to the analog voltage regulator -- clocks: an array of the MCDE clocks in this strict order: - MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI - (HDMI clock), DSI0ESCLK (DSI0 energy save clock), - DSI1ESCLK (DSI1 energy save clock), DSI2ESCLK (DSI2 energy - save clock) -- clock-names: must be the following array: - "mcde", "lcd", "hdmi" - to match the required clock inputs above. -- #address-cells: should be <1> (for the DSI hosts that will be children) -- #size-cells: should be <1> (for the DSI hosts that will be children) -- ranges: this should always be stated - -Required subnodes: - -The devicetree must specify subnodes for the DSI host adapters. -These must have the following characteristics: - -- compatible: must be: - "ste,mcde-dsi" -- reg: must specify the register range for the DSI host -- vana-supply: phandle to the VANA voltage regulator -- clocks: phandles to the high speed and low power (energy save) clocks - the high speed clock is not present on the third (dsi2) block, so it - should only have the "lp" clock -- clock-names: "hs" for the high speed clock and "lp" for the low power - (energy save) clock -- #address-cells: should be <1> -- #size-cells: should be <0> - -Display panels and bridges will appear as children on the DSI hosts, and -the displays are connected to the DSI hosts using the common binding -for video transmitter interfaces; see -Documentation/devicetree/bindings/media/video-interfaces.txt - -If a DSI host is unused (not connected) it will have no children defined. - -Example: - -mcde@a0350000 { - compatible = "ste,mcde"; - reg = <0xa0350000 0x1000>; - interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; - epod-supply = <&db8500_b2r2_mcde_reg>; - vana-supply = <&ab8500_ldo_ana_reg>; - clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */ - <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */ - <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */ - clock-names = "mcde", "lcd", "hdmi"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - dsi0: dsi@a0351000 { - compatible = "ste,mcde-dsi"; - reg = <0xa0351000 0x1000>; - vana-supply = <&ab8500_ldo_ana_reg>; - clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>; - clock-names = "hs", "lp"; - #address-cells = <1>; - #size-cells = <0>; - - panel { - compatible = "samsung,s6d16d0"; - reg = <0>; - vdd1-supply = <&ab8500_ldo_aux1_reg>; - reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; - }; - - }; - dsi1: dsi@a0352000 { - compatible = "ste,mcde-dsi"; - reg = <0xa0352000 0x1000>; - vana-supply = <&ab8500_ldo_ana_reg>; - clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>; - clock-names = "hs", "lp"; - #address-cells = <1>; - #size-cells = <0>; - }; - dsi2: dsi@a0353000 { - compatible = "ste,mcde-dsi"; - reg = <0xa0353000 0x1000>; - vana-supply = <&ab8500_ldo_ana_reg>; - /* This DSI port only has the Low Power / Energy Save clock */ - clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>; - clock-names = "lp"; - #address-cells = <1>; - #size-cells = <0>; - }; -}; diff --git a/Documentation/devicetree/bindings/display/ste,mcde.yaml b/Documentation/devicetree/bindings/display/ste,mcde.yaml new file mode 100644 index 000000000000..51851566c72d --- /dev/null +++ b/Documentation/devicetree/bindings/display/ste,mcde.yaml @@ -0,0 +1,166 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ste,mcde.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ST-Ericsson Multi Channel Display Engine MCDE + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +properties: + compatible: + const: ste,mcde + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + description: an array of the MCDE clocks + items: + - description: MCDECLK (main MCDE clock) + - description: LCDCLK (LCD clock) + - description: PLLDSI (HDMI clock) + + clock-names: + items: + - const: mcde + - const: lcd + - const: hdmi + + epod-supply: + description: a phandle to the EPOD regulator + + vana-supply: + description: a phandle to the analog voltage regulator + + port: + type: object + description: + A DPI port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + ranges: true + +patternProperties: + "^dsi@[0-9a-f]+$": + description: subnodes for the three DSI host adapters + type: object + allOf: + - $ref: dsi-controller.yaml# + properties: + compatible: + const: ste,mcde-dsi + + reg: + maxItems: 1 + + vana-supply: + description: a phandle to the analog voltage regulator + + clocks: + description: phandles to the high speed and low power (energy save) clocks + the high speed clock is not present on the third (dsi2) block, so it + should only have the "lp" clock + minItems: 1 + maxItems: 2 + + clock-names: + oneOf: + - items: + - const: hs + - const: lp + - items: + - const: lp + + required: + - compatible + - reg + - vana-supply + - clocks + - clock-names + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - epod-supply + - vana-supply + +additionalProperties: true + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/mfd/dbx500-prcmu.h> + #include <dt-bindings/gpio/gpio.h> + + mcde@a0350000 { + compatible = "ste,mcde"; + reg = <0xa0350000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + epod-supply = <&db8500_b2r2_mcde_reg>; + vana-supply = <&ab8500_ldo_ana_reg>; + clocks = <&prcmu_clk PRCMU_MCDECLK>, + <&prcmu_clk PRCMU_LCDCLK>, + <&prcmu_clk PRCMU_PLLDSI>; + clock-names = "mcde", "lcd", "hdmi"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dsi0: dsi@a0351000 { + compatible = "ste,mcde-dsi"; + reg = <0xa0351000 0x1000>; + vana-supply = <&ab8500_ldo_ana_reg>; + clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>; + clock-names = "hs", "lp"; + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,s6d16d0"; + reg = <0>; + vdd1-supply = <&ab8500_ldo_aux1_reg>; + reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + }; + }; + + dsi1: dsi@a0352000 { + compatible = "ste,mcde-dsi"; + reg = <0xa0352000 0x1000>; + vana-supply = <&ab8500_ldo_ana_reg>; + clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>; + clock-names = "hs", "lp"; + #address-cells = <1>; + #size-cells = <0>; + }; + + dsi2: dsi@a0353000 { + compatible = "ste,mcde-dsi"; + reg = <0xa0353000 0x1000>; + vana-supply = <&ab8500_ldo_ana_reg>; + /* This DSI port only has the Low Power / Energy Save clock */ + clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>; + clock-names = "lp"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + +...
This moves the MCDE bindings over to using the YAML schema to describe the ST-Ericsson MCDE display controller, making use of the generic DSI controller schema. We also add the "port" node, we will use this when adding LCD panels using the direct parallel interface DPI instead of DSI. Cc: devicetree@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v1->v2: - Cut the description on the interrupts. - Drop maxItems: 3 on clocks and clock-names: implicit from the number of listed items. - Tag the DSI ports with unevaluatedProperties: false - Tag the MCDE as such with additionalProperties: true - It was a bit hard to test this because of the code base being out of phase with the validation tools but it seems to check out. --- .../devicetree/bindings/display/ste,mcde.txt | 104 ----------- .../devicetree/bindings/display/ste,mcde.yaml | 166 ++++++++++++++++++ 2 files changed, 166 insertions(+), 104 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/ste,mcde.txt create mode 100644 Documentation/devicetree/bindings/display/ste,mcde.yaml