| Message ID | 20201128222818.1910764-5-alexandre.belloni@bootlin.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | iio: adc: at91_adc: cleanup DT bindings | expand |
On Sat, 28 Nov 2020 23:28:12 +0100 Alexandre Belloni <alexandre.belloni@bootlin.com> wrote: > From: Jonathan Cameron <Jonathan.Cameron@huawei.com> > > There are a few things we would do differently in an ADC binding if we > were starting from scratch but we are stuck with what we have (which > made sense back when this was written!) > > We may be able to tighten up some elements of this binding in the future > by careful checking of what values properties can actually take. > > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> > Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> > Cc: Nicolas Ferre <nicolas.ferre@microchip.com> > Cc: Ludovic Desroches <ludovic.desroches@microchip.com> > [Alexandre Belloni: add sama5d3, remove atmel,adc-res and atmel,adc-res-names] > Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> > Reviewed-by: Rob Herring <robh@kernel.org> > Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com> So this one is interesting from the question of what the right tag chain is. I've signed-off on it again whilst applying but also added a note to make it clear the two sign offs are actually for different things. Jonathan > --- > .../devicetree/bindings/iio/adc/at91_adc.txt | 78 -------- > .../bindings/iio/adc/atmel,sama9260-adc.yaml | 167 ++++++++++++++++++ > 2 files changed, 167 insertions(+), 78 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/iio/adc/at91_adc.txt > create mode 100644 Documentation/devicetree/bindings/iio/adc/atmel,sama9260-adc.yaml > > diff --git a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt > deleted file mode 100644 > index da393ac5c05f..000000000000 > --- a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt > +++ /dev/null > @@ -1,78 +0,0 @@ > -* AT91's Analog to Digital Converter (ADC) > - > -Required properties: > - - compatible: Should be "atmel,<chip>-adc" > - <chip> can be "at91sam9260", "at91sam9g45", "at91sam9x5" or "sama5d3" > - - reg: Should contain ADC registers location and length > - - interrupts: Should contain the IRQ line for the ADC > - - clock-names: tuple listing input clock names. > - Required elements: "adc_clk", "adc_op_clk". > - - clocks: phandles to input clocks. > - - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this > - device > - - atmel,adc-startup-time: Startup Time of the ADC in microseconds as > - defined in the datasheet > - - atmel,adc-vref: Reference voltage in millivolts for the conversions > - > -Optional properties: > - - atmel,adc-use-external-triggers: Boolean to enable the external triggers > - - atmel,adc-use-res: String selecting the resolution, can be "lowres" or > - "highres". If not specified, the highest resolution will > - be used. > - - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion > - - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds > - - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this > - value is set, then the adc driver will enable touchscreen > - support. > - NOTE: when adc touchscreen is enabled, the adc hardware trigger will be > - disabled. Since touchscreen will occupy the trigger register. > - - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It > - makes touch detection more precise. > - > -Optional trigger Nodes: > - - Required properties: > - * trigger-name: Name of the trigger exposed to the user > - * trigger-value: Value to put in the Trigger register > - to activate this trigger > - - Optional properties: > - * trigger-external: Is the trigger an external trigger? > - > -Examples: > -adc0: adc@fffb0000 { > - #address-cells = <1>; > - #size-cells = <0>; > - compatible = "atmel,at91sam9260-adc"; > - reg = <0xfffb0000 0x100>; > - interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; > - clocks = <&adc_clk>, <&adc_op_clk>; > - clock-names = "adc_clk", "adc_op_clk"; > - atmel,adc-channels-used = <0xff>; > - atmel,adc-startup-time = <40>; > - atmel,adc-use-external-triggers; > - atmel,adc-vref = <3300>; > - atmel,adc-res = <8 10>; > - atmel,adc-res-names = "lowres", "highres"; > - atmel,adc-use-res = "lowres"; > - > - trigger0 { > - trigger-name = "external-rising"; > - trigger-value = <0x1>; > - trigger-external; > - }; > - trigger1 { > - trigger-name = "external-falling"; > - trigger-value = <0x2>; > - trigger-external; > - }; > - > - trigger2 { > - trigger-name = "external-any"; > - trigger-value = <0x3>; > - trigger-external; > - }; > - > - trigger3 { > - trigger-name = "continuous"; > - trigger-value = <0x6>; > - }; > -}; > diff --git a/Documentation/devicetree/bindings/iio/adc/atmel,sama9260-adc.yaml b/Documentation/devicetree/bindings/iio/adc/atmel,sama9260-adc.yaml > new file mode 100644 > index 000000000000..9b0ff59e75de > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/adc/atmel,sama9260-adc.yaml > @@ -0,0 +1,167 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/iio/adc/atmel,sama9260-adc.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: AT91 sama9260 and similar Analog to Digital Converter (ADC) > + > +maintainers: > + - Alexandre Belloni <alexandre.belloni@bootlin.com> > + > +properties: > + compatible: > + enum: > + - atmel,at91sam9260-adc > + - atmel,at91sam9rl-adc > + - atmel,at91sam9g45-adc > + - atmel,at91sam9x5-adc > + - atmel,at91sama5d3-adc > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + clocks: > + minItems: 2 > + maxItems: 2 > + > + clock-names: > + items: > + - const: adc_clk > + - const: adc_op_clk > + > + atmel,adc-channels-used: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Bitmask of the channels muxed and enabled for this device > + > + atmel,adc-startup-time: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Startup Time of the ADC in microseconds as defined in the datasheet > + > + atmel,adc-vref: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Reference voltage in millivolts for the conversions > + > + atmel,adc-use-external-triggers: > + $ref: /schemas/types.yaml#/definitions/flag > + description: Enable the external triggers > + > + atmel,adc-use-res: > + $ref: /schemas/types.yaml#/definitions/string > + description: > + String corresponding to an identifier from atmel,adc-res-names property. > + If not specified, the highest resolution will be used. > + enum: > + - "lowres" > + - "highres" > + > + atmel,adc-sleep-mode: > + $ref: /schemas/types.yaml#/definitions/flag > + description: Enable sleep mode when no conversion > + > + atmel,adc-sample-hold-time: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Sample and Hold Time in microseconds > + > + atmel,adc-ts-wires: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: | > + Number of touchscreen wires. Must be set to enable touchscreen. > + NOTE: when adc touchscreen is enabled, the adc hardware trigger will be > + disabled. Since touchscreen will occupy the trigger register. > + enum: > + - 4 > + - 5 > + > + atmel,adc-ts-pressure-threshold: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Pressure threshold for touchscreen. > + > + "#io-channel-cells": > + const: 1 > + > +additionalProperties: false > + > +required: > + - compatible > + - reg > + - interrupts > + - clocks > + - clock-names > + - atmel,adc-channels-used > + - atmel,adc-startup-time > + - atmel,adc-vref > + > +patternProperties: > + "^(trigger)[0-9]$": > + type: object > + description: Child node to describe a trigger exposed to the user. > + properties: > + trigger-name: > + $ref: /schemas/types.yaml#/definitions/string > + description: Identifying name. > + > + trigger-value: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Value to put in the Trigger register to activate this trigger > + > + trigger-external: > + $ref: /schemas/types.yaml#/definitions/flag > + description: This trigger is provided from an external pin. > + > + additionalProperties: false > + required: > + - trigger-name > + - trigger-value > + > +examples: > + - | > + #include <dt-bindings/dma/at91.h> > + #include <dt-bindings/interrupt-controller/irq.h> > + soc { > + #address-cells = <1>; > + #size-cells = <1>; > + > + adc@fffb0000 { > + compatible = "atmel,at91sam9260-adc"; > + reg = <0xfffb0000 0x100>; > + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&adc_clk>, <&adc_op_clk>; > + clock-names = "adc_clk", "adc_op_clk"; > + atmel,adc-channels-used = <0xff>; > + atmel,adc-startup-time = <40>; > + atmel,adc-use-external-triggers; > + atmel,adc-vref = <3300>; > + atmel,adc-use-res = "lowres"; > + > + trigger0 { > + trigger-name = "external-rising"; > + trigger-value = <0x1>; > + trigger-external; > + }; > + > + trigger1 { > + trigger-name = "external-falling"; > + trigger-value = <0x2>; > + trigger-external; > + }; > + > + trigger2 { > + trigger-name = "external-any"; > + trigger-value = <0x3>; > + trigger-external; > + }; > + > + trigger3 { > + trigger-name = "continuous"; > + trigger-value = <0x6>; > + }; > + }; > + }; > +...
diff --git a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt deleted file mode 100644 index da393ac5c05f..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt +++ /dev/null @@ -1,78 +0,0 @@ -* AT91's Analog to Digital Converter (ADC) - -Required properties: - - compatible: Should be "atmel,<chip>-adc" - <chip> can be "at91sam9260", "at91sam9g45", "at91sam9x5" or "sama5d3" - - reg: Should contain ADC registers location and length - - interrupts: Should contain the IRQ line for the ADC - - clock-names: tuple listing input clock names. - Required elements: "adc_clk", "adc_op_clk". - - clocks: phandles to input clocks. - - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this - device - - atmel,adc-startup-time: Startup Time of the ADC in microseconds as - defined in the datasheet - - atmel,adc-vref: Reference voltage in millivolts for the conversions - -Optional properties: - - atmel,adc-use-external-triggers: Boolean to enable the external triggers - - atmel,adc-use-res: String selecting the resolution, can be "lowres" or - "highres". If not specified, the highest resolution will - be used. - - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion - - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds - - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this - value is set, then the adc driver will enable touchscreen - support. - NOTE: when adc touchscreen is enabled, the adc hardware trigger will be - disabled. Since touchscreen will occupy the trigger register. - - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It - makes touch detection more precise. - -Optional trigger Nodes: - - Required properties: - * trigger-name: Name of the trigger exposed to the user - * trigger-value: Value to put in the Trigger register - to activate this trigger - - Optional properties: - * trigger-external: Is the trigger an external trigger? - -Examples: -adc0: adc@fffb0000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "atmel,at91sam9260-adc"; - reg = <0xfffb0000 0x100>; - interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&adc_clk>, <&adc_op_clk>; - clock-names = "adc_clk", "adc_op_clk"; - atmel,adc-channels-used = <0xff>; - atmel,adc-startup-time = <40>; - atmel,adc-use-external-triggers; - atmel,adc-vref = <3300>; - atmel,adc-res = <8 10>; - atmel,adc-res-names = "lowres", "highres"; - atmel,adc-use-res = "lowres"; - - trigger0 { - trigger-name = "external-rising"; - trigger-value = <0x1>; - trigger-external; - }; - trigger1 { - trigger-name = "external-falling"; - trigger-value = <0x2>; - trigger-external; - }; - - trigger2 { - trigger-name = "external-any"; - trigger-value = <0x3>; - trigger-external; - }; - - trigger3 { - trigger-name = "continuous"; - trigger-value = <0x6>; - }; -}; diff --git a/Documentation/devicetree/bindings/iio/adc/atmel,sama9260-adc.yaml b/Documentation/devicetree/bindings/iio/adc/atmel,sama9260-adc.yaml new file mode 100644 index 000000000000..9b0ff59e75de --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/atmel,sama9260-adc.yaml @@ -0,0 +1,167 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/atmel,sama9260-adc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AT91 sama9260 and similar Analog to Digital Converter (ADC) + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + +properties: + compatible: + enum: + - atmel,at91sam9260-adc + - atmel,at91sam9rl-adc + - atmel,at91sam9g45-adc + - atmel,at91sam9x5-adc + - atmel,at91sama5d3-adc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 2 + + clock-names: + items: + - const: adc_clk + - const: adc_op_clk + + atmel,adc-channels-used: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Bitmask of the channels muxed and enabled for this device + + atmel,adc-startup-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Startup Time of the ADC in microseconds as defined in the datasheet + + atmel,adc-vref: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Reference voltage in millivolts for the conversions + + atmel,adc-use-external-triggers: + $ref: /schemas/types.yaml#/definitions/flag + description: Enable the external triggers + + atmel,adc-use-res: + $ref: /schemas/types.yaml#/definitions/string + description: + String corresponding to an identifier from atmel,adc-res-names property. + If not specified, the highest resolution will be used. + enum: + - "lowres" + - "highres" + + atmel,adc-sleep-mode: + $ref: /schemas/types.yaml#/definitions/flag + description: Enable sleep mode when no conversion + + atmel,adc-sample-hold-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Sample and Hold Time in microseconds + + atmel,adc-ts-wires: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Number of touchscreen wires. Must be set to enable touchscreen. + NOTE: when adc touchscreen is enabled, the adc hardware trigger will be + disabled. Since touchscreen will occupy the trigger register. + enum: + - 4 + - 5 + + atmel,adc-ts-pressure-threshold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Pressure threshold for touchscreen. + + "#io-channel-cells": + const: 1 + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - atmel,adc-channels-used + - atmel,adc-startup-time + - atmel,adc-vref + +patternProperties: + "^(trigger)[0-9]$": + type: object + description: Child node to describe a trigger exposed to the user. + properties: + trigger-name: + $ref: /schemas/types.yaml#/definitions/string + description: Identifying name. + + trigger-value: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Value to put in the Trigger register to activate this trigger + + trigger-external: + $ref: /schemas/types.yaml#/definitions/flag + description: This trigger is provided from an external pin. + + additionalProperties: false + required: + - trigger-name + - trigger-value + +examples: + - | + #include <dt-bindings/dma/at91.h> + #include <dt-bindings/interrupt-controller/irq.h> + soc { + #address-cells = <1>; + #size-cells = <1>; + + adc@fffb0000 { + compatible = "atmel,at91sam9260-adc"; + reg = <0xfffb0000 0x100>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&adc_clk>, <&adc_op_clk>; + clock-names = "adc_clk", "adc_op_clk"; + atmel,adc-channels-used = <0xff>; + atmel,adc-startup-time = <40>; + atmel,adc-use-external-triggers; + atmel,adc-vref = <3300>; + atmel,adc-use-res = "lowres"; + + trigger0 { + trigger-name = "external-rising"; + trigger-value = <0x1>; + trigger-external; + }; + + trigger1 { + trigger-name = "external-falling"; + trigger-value = <0x2>; + trigger-external; + }; + + trigger2 { + trigger-name = "external-any"; + trigger-value = <0x3>; + trigger-external; + }; + + trigger3 { + trigger-name = "continuous"; + trigger-value = <0x6>; + }; + }; + }; +...