@@ -137,45 +137,25 @@ struct raydium_data {
bool wake_irq_enabled;
};
-static int raydium_i2c_xfer(struct i2c_client *client,
- u32 addr, void *data, size_t len, bool is_read)
-{
- struct raydium_bank_switch_header {
- u8 cmd;
- __be32 be_addr;
- } __packed header = {
- .cmd = RM_CMD_BANK_SWITCH,
- .be_addr = cpu_to_be32(addr),
- };
-
- u8 reg_addr = addr & 0xff;
-
- struct i2c_msg xfer[] = {
- {
- .addr = client->addr,
- .len = sizeof(header),
- .buf = (u8 *)&header,
- },
- {
- .addr = client->addr,
- .len = 1,
- .buf = ®_addr,
- },
- {
- .addr = client->addr,
- .len = len,
- .buf = data,
- .flags = is_read ? I2C_M_RD : 0,
- }
- };
+/*
+ * Header to be sent for RM_CMD_BANK_SWITCH command. This is used by
+ * raydium_i2c_{read|send} below.
+ */
+struct __packed raydium_bank_switch_header {
+ u8 cmd;
+ __be32 be_addr;
+};
+static int raydium_i2c_xfer(struct i2c_client *client, u32 addr,
+ struct i2c_msg *xfer, size_t xfer_count)
+{
+ int ret;
/*
* If address is greater than 255, then RM_CMD_BANK_SWITCH needs to be
* sent first. Else, skip the header i.e. xfer[0].
*/
int xfer_start_idx = (addr > 0xff) ? 0 : 1;
- size_t xfer_count = ARRAY_SIZE(xfer) - xfer_start_idx;
- int ret;
+ xfer_count -= xfer_start_idx;
ret = i2c_transfer(client->adapter, &xfer[xfer_start_idx], xfer_count);
if (likely(ret == xfer_count))
@@ -189,10 +169,46 @@ static int raydium_i2c_send(struct i2c_client *client,
{
int tries = 0;
int error;
+ u8 *tx_buf;
+ u8 reg_addr = addr & 0xff;
+
+ tx_buf = kmalloc(len + 1, GFP_KERNEL);
+ if (!tx_buf)
+ return -ENOMEM;
+
+ tx_buf[0] = reg_addr;
+ memcpy(tx_buf + 1, data, len);
do {
- error = raydium_i2c_xfer(client, addr, (void *)data, len,
- false);
+ struct raydium_bank_switch_header header = {
+ .cmd = RM_CMD_BANK_SWITCH,
+ .be_addr = cpu_to_be32(addr),
+ };
+
+ /*
+ * Perform as a single i2c_transfer transaction to ensure that
+ * no other I2C transactions are initiated on the bus to any
+ * other device in between. Initiating transacations to other
+ * devices after RM_CMD_BANK_SWITCH is sent is known to cause
+ * issues. This is also why regmap infrastructure cannot be used
+ * for this driver. Regmap handles page(bank) switch and reads
+ * as separate i2c_transfer() operations. This can result in
+ * problems if the Raydium device is on a shared I2C bus.
+ */
+ struct i2c_msg xfer[] = {
+ {
+ .addr = client->addr,
+ .len = sizeof(header),
+ .buf = (u8 *)&header,
+ },
+ {
+ .addr = client->addr,
+ .len = len + 1,
+ .buf = tx_buf,
+ },
+ };
+
+ error = raydium_i2c_xfer(client, addr, xfer, ARRAY_SIZE(xfer));
if (likely(!error))
return 0;
@@ -206,12 +222,46 @@ static int raydium_i2c_send(struct i2c_client *client,
static int raydium_i2c_read(struct i2c_client *client,
u32 addr, void *data, size_t len)
{
- size_t xfer_len;
int error;
while (len) {
- xfer_len = min_t(size_t, len, RM_MAX_READ_SIZE);
- error = raydium_i2c_xfer(client, addr, data, xfer_len, true);
+ u8 reg_addr = addr & 0xff;
+ struct raydium_bank_switch_header header = {
+ .cmd = RM_CMD_BANK_SWITCH,
+ .be_addr = cpu_to_be32(addr),
+ };
+ size_t xfer_len = min_t(size_t, len, RM_MAX_READ_SIZE);
+
+ /*
+ * Perform as a single i2c_transfer transaction to ensure that
+ * no other I2C transactions are initiated on the bus to any
+ * other device in between. Initiating transacations to other
+ * devices after RM_CMD_BANK_SWITCH is sent is known to cause
+ * issues. This is also why regmap infrastructure cannot be used
+ * for this driver. Regmap handles page(bank) switch and writes
+ * as separate i2c_transfer() operations. This can result in
+ * problems if the Raydium device is on a shared I2C bus.
+ */
+ struct i2c_msg xfer[] = {
+ {
+ .addr = client->addr,
+ .len = sizeof(header),
+ .buf = (u8 *)&header,
+ },
+ {
+ .addr = client->addr,
+ .len = 1,
+ .buf = ®_addr,
+ },
+ {
+ .addr = client->addr,
+ .len = xfer_len,
+ .buf = data,
+ .flags = I2C_M_RD,
+ }
+ };
+
+ error = raydium_i2c_xfer(client, addr, xfer, ARRAY_SIZE(xfer));
if (unlikely(error))
return error;
Raydium device does not like splitting of tx transactions into multiple messages - one for the register address and one for the actual data. This results in incorrect behavior on the device side. This change updates raydium_i2c_read and raydium_i2c_write to create i2c_msg arrays separately and passes those arrays into raydium_i2c_xfer which decides based on the address whether the bank switch command should be sent. The bank switch header is still added by raydium_i2c_read and raydium_i2c_write to ensure that all these operations are performed as part of a single I2C transfer. It guarantees that no other transactions are initiated to any other device on the same bus after the bank switch command is sent. Signed-off-by: Furquan Shaikh <furquan@google.com> --- v2: Added comment in raydium_i2c_{send|read} about why regmap infrastructure cannot be used for this driver as it splits bank switch and i2c read/write into separate i2c_transfer calls which is known to create problems with Raydium device. drivers/input/touchscreen/raydium_i2c_ts.c | 126 ++++++++++++++------- 1 file changed, 88 insertions(+), 38 deletions(-)