@@ -58,13 +58,15 @@ static void bcm2835_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
writel(value, pc->base + PWM_CONTROL);
}
-static int bcm2835_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
- int duty_ns, int period_ns)
+static int bcm2835_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
{
+
struct bcm2835_pwm *pc = to_bcm2835_pwm(chip);
unsigned long rate = clk_get_rate(pc->clk);
+ unsigned long long period;
unsigned long scaler;
- u32 period;
+ u32 val;
if (!rate) {
dev_err(pc->dev, "failed to get clock rate\n");
@@ -72,54 +74,34 @@ static int bcm2835_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
}
scaler = DIV_ROUND_CLOSEST(NSEC_PER_SEC, rate);
- period = DIV_ROUND_CLOSEST(period_ns, scaler);
+ /* set period */
+ period = DIV_ROUND_CLOSEST_ULL(state->period, scaler);
- if (period < PERIOD_MIN)
+ /* dont accept a period that is too small or has been truncated */
+ if ((period < PERIOD_MIN) || (period > U32_MAX))
return -EINVAL;
- writel(DIV_ROUND_CLOSEST(duty_ns, scaler),
- pc->base + DUTY(pwm->hwpwm));
writel(period, pc->base + PERIOD(pwm->hwpwm));
- return 0;
-}
-
-static int bcm2835_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
-{
- struct bcm2835_pwm *pc = to_bcm2835_pwm(chip);
- u32 value;
-
- value = readl(pc->base + PWM_CONTROL);
- value |= PWM_ENABLE << PWM_CONTROL_SHIFT(pwm->hwpwm);
- writel(value, pc->base + PWM_CONTROL);
+ /* set duty cycle */
+ val = DIV_ROUND_CLOSEST_ULL(state->duty_cycle, scaler);
+ writel(val, pc->base + DUTY(pwm->hwpwm));
- return 0;
-}
+ /* set polarity */
+ val = readl(pc->base + PWM_CONTROL);
-static void bcm2835_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
-{
- struct bcm2835_pwm *pc = to_bcm2835_pwm(chip);
- u32 value;
-
- value = readl(pc->base + PWM_CONTROL);
- value &= ~(PWM_ENABLE << PWM_CONTROL_SHIFT(pwm->hwpwm));
- writel(value, pc->base + PWM_CONTROL);
-}
-
-static int bcm2835_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm,
- enum pwm_polarity polarity)
-{
- struct bcm2835_pwm *pc = to_bcm2835_pwm(chip);
- u32 value;
-
- value = readl(pc->base + PWM_CONTROL);
+ if (state->polarity == PWM_POLARITY_NORMAL)
+ val &= ~(PWM_POLARITY << PWM_CONTROL_SHIFT(pwm->hwpwm));
+ else
+ val |= PWM_POLARITY << PWM_CONTROL_SHIFT(pwm->hwpwm);
- if (polarity == PWM_POLARITY_NORMAL)
- value &= ~(PWM_POLARITY << PWM_CONTROL_SHIFT(pwm->hwpwm));
+ /* enable/disable */
+ if (state->enabled)
+ val |= PWM_ENABLE << PWM_CONTROL_SHIFT(pwm->hwpwm);
else
- value |= PWM_POLARITY << PWM_CONTROL_SHIFT(pwm->hwpwm);
+ val &= ~(PWM_ENABLE << PWM_CONTROL_SHIFT(pwm->hwpwm));
- writel(value, pc->base + PWM_CONTROL);
+ writel(val, pc->base + PWM_CONTROL);
return 0;
}
@@ -127,10 +109,7 @@ static int bcm2835_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm,
static const struct pwm_ops bcm2835_pwm_ops = {
.request = bcm2835_pwm_request,
.free = bcm2835_pwm_free,
- .config = bcm2835_pwm_config,
- .enable = bcm2835_pwm_enable,
- .disable = bcm2835_pwm_disable,
- .set_polarity = bcm2835_set_polarity,
+ .apply = bcm2835_pwm_apply,
.owner = THIS_MODULE,
};
Use the newer .apply function of pwm_ops instead of .config, .enable, .disable and .set_polarity. This guarantees atomic changes of the pwm controller configuration. It also reduces the size of the driver. Since now period is a 64 bit value, add an extra check to reject periods that exceed the possible max value for the 32 bit register. This has been tested on a Raspberry PI 4. Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> --- v4: Remove a superfluous blank line Remove an unneeded cast (both requested by Uwe Kleine-König) v3: Check against period truncation (also based on a review by Uwe) v2: Fix compiler error for 64 bit builds drivers/pwm/pwm-bcm2835.c | 69 +++++++++++++++++------------------------------ 1 file changed, 24 insertions(+), 45 deletions(-) j