| Message ID | 20201227105449.11452-4-roger.lu@mediatek.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | soc: mediatek: SVS: introduce MTK SVS engine | expand |
On Sun, Dec 27, 2020 at 6:55 PM Roger Lu <roger.lu@mediatek.com> wrote: > > The Smart Voltage Scaling(SVS) engine is a piece of hardware > which calculats suitable SVS bank voltages to OPP voltage table. calculates > Then, DVFS driver could apply those SVS bank voltages to PMIC/Buck > when receiving OPP_EVENT_ADJUST_VOLTAGE. > > Signed-off-by: Roger Lu <roger.lu@mediatek.com> > --- > drivers/soc/mediatek/Kconfig | 10 + > drivers/soc/mediatek/Makefile | 1 + > drivers/soc/mediatek/mtk-svs.c | 1748 ++++++++++++++++++++++++++++++++ > 3 files changed, 1759 insertions(+) > create mode 100644 drivers/soc/mediatek/mtk-svs.c > > diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig > index 59a56cd790ec..f33da25f8336 100644 > --- a/drivers/soc/mediatek/Kconfig > +++ b/drivers/soc/mediatek/Kconfig > @@ -51,4 +51,14 @@ config MTK_MMSYS > Say yes here to add support for the MediaTek Multimedia > Subsystem (MMSYS). > > +config MTK_SVS > + tristate "MediaTek Smart Voltage Scaling(SVS)" > + depends on MTK_EFUSE && NVMEM > + help > + The Smart Voltage Scaling(SVS) engine is a piece of hardware > + which has several controllers(banks) for calculating suitable > + voltage to different power domains(CPU/GPU/CCI) according to > + chip process corner, temperatures and other factors. Then DVFS > + driver could apply SVS bank voltage to PMIC/Buck. > + > endmenu > diff --git a/drivers/soc/mediatek/Makefile b/drivers/soc/mediatek/Makefile > index 01f9f873634a..e10f2cd87514 100644 > --- a/drivers/soc/mediatek/Makefile > +++ b/drivers/soc/mediatek/Makefile > @@ -4,3 +4,4 @@ obj-$(CONFIG_MTK_INFRACFG) += mtk-infracfg.o > obj-$(CONFIG_MTK_PMIC_WRAP) += mtk-pmic-wrap.o > obj-$(CONFIG_MTK_SCPSYS) += mtk-scpsys.o > obj-$(CONFIG_MTK_MMSYS) += mtk-mmsys.o > +obj-$(CONFIG_MTK_SVS) += mtk-svs.o > diff --git a/drivers/soc/mediatek/mtk-svs.c b/drivers/soc/mediatek/mtk-svs.c > new file mode 100644 > index 000000000000..0efefb48839d > --- /dev/null > +++ b/drivers/soc/mediatek/mtk-svs.c > @@ -0,0 +1,1748 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Copyright (C) 2020 MediaTek Inc. > + */ > + > +#include <linux/bits.h> > +#include <linux/clk.h> > +#include <linux/completion.h> > +#include <linux/device.h> > +#include <linux/init.h> > +#include <linux/interrupt.h> > +#include <linux/kernel.h> > +#include <linux/kthread.h> > +#include <linux/module.h> > +#include <linux/mutex.h> > +#include <linux/nvmem-consumer.h> > +#include <linux/of_address.h> > +#include <linux/of_irq.h> > +#include <linux/of_platform.h> > +#include <linux/platform_device.h> > +#include <linux/pm_domain.h> > +#include <linux/pm_opp.h> > +#include <linux/pm_qos.h> > +#include <linux/pm_runtime.h> > +#include <linux/regulator/consumer.h> > +#include <linux/reset.h> > +#include <linux/slab.h> > +#include <linux/spinlock.h> > +#include <linux/thermal.h> > + > +/* svs bank 1-line sw id */ > +#define SVSB_CPU_LITTLE BIT(0) > +#define SVSB_CPU_BIG BIT(1) > +#define SVSB_CCI BIT(2) > +#define SVSB_GPU BIT(3) > + > +/* svs bank mode support */ > +#define SVSB_MODE_ALL_DISABLE 0 > +#define SVSB_MODE_INIT01 BIT(1) > +#define SVSB_MODE_INIT02 BIT(2) > +#define SVSB_MODE_MON BIT(3) > + > +/* svs bank init01 condition */ > +#define SVSB_INIT01_VOLT_IGNORE BIT(1) > +#define SVSB_INIT01_VOLT_INC_ONLY BIT(2) > +#define SVSB_INIT01_CLK_EN BIT(31) > + > +/* svs bank common setting */ > +#define SVSB_TZONE_HIGH_TEMP_MAX U32_MAX > +#define SVSB_RUNCONFIG_DEFAULT 0x80000000 > +#define SVSB_DC_SIGNED_BIT 0x8000 > +#define SVSB_INTEN_INIT0x 0x00005f01 > +#define SVSB_INTEN_MONVOPEN 0x00ff0000 > +#define SVSB_EN_OFF 0x0 > +#define SVSB_EN_MASK 0x7 > +#define SVSB_EN_INIT01 0x1 > +#define SVSB_EN_INIT02 0x5 > +#define SVSB_EN_MON 0x2 > +#define SVSB_INTSTS_MONVOP 0x00ff0000 > +#define SVSB_INTSTS_COMPLETE 0x1 > +#define SVSB_INTSTS_CLEAN 0x00ffffff > + > +static DEFINE_SPINLOCK(mtk_svs_lock); > + > +/* > + * enum svsb_phase - svs bank phase enumeration > + * @SVSB_PHASE_INIT01: basic init for svs bank > + * @SVSB_PHASE_INIT02: svs bank can provide voltages > + * @SVSB_PHASE_MON: svs bank can provide voltages with thermal effect > + * @SVSB_PHASE_ERROR: svs bank encouters unexpected condition encounters > + * > + * Each svs bank has its own independent phase. We enable each svs bank by > + * running their phase orderly. However, When svs bank ecnounters unexpected encounters > + * condition, it will fire an irq (PHASE_ERROR) to inform svs software. > + * > + * svs bank general phase-enabled order: > + * SVSB_PHASE_INIT01 -> SVSB_PHASE_INIT02 -> SVSB_PHASE_MON > + */ > +enum svsb_phase { > + SVSB_PHASE_INIT01 = 0, > + SVSB_PHASE_INIT02, > + SVSB_PHASE_MON, > + SVSB_PHASE_ERROR, > +}; > + > +enum svs_reg_index { > + DESCHAR = 0, > + TEMPCHAR, > + DETCHAR, > + AGECHAR, > + DCCONFIG, > + AGECONFIG, > + FREQPCT30, > + FREQPCT74, > + LIMITVALS, > + VBOOT, > + DETWINDOW, > + CONFIG, > + TSCALCS, > + RUNCONFIG, > + SVSEN, > + INIT2VALS, > + DCVALUES, > + AGEVALUES, > + VOP30, > + VOP74, > + TEMP, > + INTSTS, > + INTSTSRAW, > + INTEN, > + CHKINT, > + CHKSHIFT, > + STATUS, > + VDESIGN30, > + VDESIGN74, > + DVT30, > + DVT74, > + AGECOUNT, > + SMSTATE0, > + SMSTATE1, > + CTL0, > + DESDETSEC, > + TEMPAGESEC, > + CTRLSPARE0, > + CTRLSPARE1, > + CTRLSPARE2, > + CTRLSPARE3, > + CORESEL, > + THERMINTST, > + INTST, > + THSTAGE0ST, > + THSTAGE1ST, > + THSTAGE2ST, > + THAHBST0, > + THAHBST1, > + SPARE0, > + SPARE1, > + SPARE2, > + SPARE3, > + THSLPEVEB, > + reg_num, What do you need reg_num for? Maybe remove it? If you need it, it should probably be named SVS_REG_NUM. > +}; > + > +static const u32 svs_regs_v2[] = { > + [DESCHAR] = 0xc00, > + [TEMPCHAR] = 0xc04, > + [DETCHAR] = 0xc08, > + [AGECHAR] = 0xc0c, > + [DCCONFIG] = 0xc10, > + [AGECONFIG] = 0xc14, > + [FREQPCT30] = 0xc18, > + [FREQPCT74] = 0xc1c, > + [LIMITVALS] = 0xc20, > + [VBOOT] = 0xc24, > + [DETWINDOW] = 0xc28, > + [CONFIG] = 0xc2c, > + [TSCALCS] = 0xc30, > + [RUNCONFIG] = 0xc34, > + [SVSEN] = 0xc38, > + [INIT2VALS] = 0xc3c, > + [DCVALUES] = 0xc40, > + [AGEVALUES] = 0xc44, > + [VOP30] = 0xc48, > + [VOP74] = 0xc4c, > + [TEMP] = 0xc50, > + [INTSTS] = 0xc54, > + [INTSTSRAW] = 0xc58, > + [INTEN] = 0xc5c, > + [CHKINT] = 0xc60, > + [CHKSHIFT] = 0xc64, > + [STATUS] = 0xc68, > + [VDESIGN30] = 0xc6c, > + [VDESIGN74] = 0xc70, > + [DVT30] = 0xc74, > + [DVT74] = 0xc78, > + [AGECOUNT] = 0xc7c, > + [SMSTATE0] = 0xc80, > + [SMSTATE1] = 0xc84, > + [CTL0] = 0xc88, > + [DESDETSEC] = 0xce0, > + [TEMPAGESEC] = 0xce4, > + [CTRLSPARE0] = 0xcf0, > + [CTRLSPARE1] = 0xcf4, > + [CTRLSPARE2] = 0xcf8, > + [CTRLSPARE3] = 0xcfc, > + [CORESEL] = 0xf00, > + [THERMINTST] = 0xf04, > + [INTST] = 0xf08, > + [THSTAGE0ST] = 0xf0c, > + [THSTAGE1ST] = 0xf10, > + [THSTAGE2ST] = 0xf14, > + [THAHBST0] = 0xf18, > + [THAHBST1] = 0xf1c, > + [SPARE0] = 0xf20, > + [SPARE1] = 0xf24, > + [SPARE2] = 0xf28, > + [SPARE3] = 0xf2c, > + [THSLPEVEB] = 0xf30, > +}; > + > +/* > + * struct thermal_parameter - This is for storing thermal efuse data. > + * We cacluate thermal efuse data to produce "mts" and "bts" for calculate > + * svs bank mon mode. > + */ > +struct thermal_parameter { > + int adc_ge_t; > + int adc_oe_t; > + int ge; > + int oe; > + int gain; > + int o_vtsabb; > + int o_vtsmcu1; > + int o_vtsmcu2; > + int o_vtsmcu3; > + int o_vtsmcu4; > + int o_vtsmcu5; > + int degc_cali; > + int adc_cali_en_t; > + int o_slope; > + int o_slope_sign; > + int ts_id; > +}; > + > +/* > + * struct svs_bank - svs bank representation > + * @dev: svs bank device > + * @opp_dev: device for opp table/buck control > + * @pd_dev: power domain device for SOC mtcmos control > + * @init_completion: the timeout completion for bank init > + * @buck: phandle of the regulator > + * @lock: mutex lock to protect voltage update process > + * @suspended: suspend flag of this bank > + * @pd_req: bank's power-domain on request > + * @volt_offset: bank voltage offset controlled by svs software > + * @mode_support: bank mode support. > + * @opp_freqs: signed-off frequencies from default opp table > + * @opp_volts: signed-off voltages from default opp table > + * @freqs_pct: percent of "opp_freqs / freq_base" for bank init > + * @volts: bank voltages > + * @freq_base: reference frequency for bank init > + * @vboot: voltage request for bank init01 stage only > + * @volt_step: bank voltage step > + * @volt_base: bank voltage base > + * @init01_volt_flag: bank init01 voltage flag > + * @phase: bank current phase > + * @vmax: bank voltage maximum > + * @vmin: bank votlage minimum voltage > + * @temp: bank temperature > + * @temp_upper_bound: bank temperature upper bound > + * @temp_lower_bound: bank temperature lower bound > + * @tzone_high_temp: thermal zone high temperature threshold > + * @tzone_high_temp_offset: thermal zone high temperature offset > + * @tzone_low_temp: thermal zone low temperature threshold > + * @tzone_low_temp_offset: thermal zone low temperature offset > + * @core_sel: bank selection > + * @opp_count: bank opp count > + * @int_st: bank interrupt identification > + * @sw_id: bank software identification > + * @ctl0: bank thermal sensor selection > + * @cpu_id: cpu core id for SVS CPU only > + * @name: bank name > + * @tzone_name: thermal zone name > + * @buck_name: regulator name > + * > + * Other structure members which are not listed above are svs platform > + * efuse data for bank init > + */ > +struct svs_bank { > + struct device *dev; > + struct device *opp_dev; > + struct device *pd_dev; > + struct completion init_completion; > + struct regulator *buck; > + struct mutex lock; /* lock to protect voltage update process */ > + bool suspended; > + bool pd_req; > + s32 volt_offset; > + u32 mode_support; > + u32 opp_freqs[16]; > + u32 opp_volts[16]; > + u32 freqs_pct[16]; > + u32 volts[16]; > + u32 freq_base; > + u32 vboot; > + u32 volt_step; > + u32 volt_base; > + u32 init01_volt_flag; > + u32 phase; > + u32 vmax; > + u32 vmin; > + u32 bts; > + u32 mts; > + u32 bdes; > + u32 mdes; > + u32 mtdes; > + u32 dcbdet; > + u32 dcmdet; > + u32 dthi; > + u32 dtlo; > + u32 det_window; > + u32 det_max; > + u32 age_config; > + u32 age_voffset_in; > + u32 agem; > + u32 dc_config; > + u32 dc_voffset_in; > + u32 dvt_fixed; > + u32 vco; > + u32 chk_shift; > + u32 temp; > + u32 temp_upper_bound; > + u32 temp_lower_bound; > + u32 tzone_high_temp; > + u32 tzone_high_temp_offset; > + u32 tzone_low_temp; > + u32 tzone_low_temp_offset; > + u32 core_sel; > + u32 opp_count; > + u32 int_st; > + u32 sw_id; > + u32 ctl0; > + u32 cpu_id; > + u8 *name; > + u8 *tzone_name; > + u8 *buck_name; > +}; > + > +/* > + * struct svs_platform - svs platform data > + * @dev: svs platform device > + * @base: svs platform register address base > + * @main_clk: main clock for svs bank > + * @pbank: phandle of svs bank and needs to be protected by spin_lock > + * @banks: phandle of the banks that support > + * @efuse_parsing: phandle of efuse parsing function > + * @set_freqs_pct: phandle of set frequencies percent function > + * @get_vops: phandle of get bank voltages function > + * @irqflags: irq settings flags > + * @fake_efuse: the flag for running svs with fake efuse > + * @rst: svs reset control > + * @regs: phandle to the registers map > + * @efuse_num: the total number of svs platform efuse > + * @tefuse_num: the total number of thermal efuse > + * @bank_num: the total number of banks > + * @efuse_check: the svs efuse check index > + * @efuse: svs platform efuse data received from NVMEM framework > + * @tefuse: thermal efuse data received from NVMEM framework > + * @name: svs platform name > + */ > +struct svs_platform { > + struct device *dev; > + void __iomem *base; > + struct clk *main_clk; > + struct svs_bank *pbank; > + struct svs_bank *banks; > + bool (*efuse_parsing)(struct svs_platform *svsp); > + void (*set_freqs_pct)(struct svs_platform *svsp); > + void (*get_vops)(struct svs_platform *svsp); > + unsigned long irqflags; > + bool fake_efuse; > + struct reset_control *rst; > + const u32 *regs; > + size_t efuse_num; > + size_t tefuse_num; > + u32 bank_num; > + u32 efuse_check; > + u32 *efuse; > + u32 *tefuse; > + u8 *name; > +}; > + > +static u32 percent(u32 numerator, u32 denominator) > +{ > + u32 pct; > + > + /* If not divide 1000, "numerator * 100" will have data overflow. */ > + numerator /= 1000; > + denominator /= 1000; > + pct = ((numerator * 100) + denominator - 1) / denominator; pct = DIV_ROUND_UP(numerator * 100, denominator); > + pct &= GENMASK(7, 0); Why do you need this? Maybe you should just return a u8 here? > + > + return pct; > +} > + > +static u32 svs_readl(struct svs_platform *svsp, enum svs_reg_index rg_i) > +{ > + return readl(svsp->base + svsp->regs[rg_i]); > +} > + > +static void svs_writel(struct svs_platform *svsp, u32 val, > + enum svs_reg_index rg_i) > +{ > + writel(val, svsp->base + svsp->regs[rg_i]); > +} > + > +static void svs_switch_bank(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb = svsp->pbank; > + > + svs_writel(svsp, svsb->core_sel, CORESEL); > +} > + > +static u32 svs_bank_volt_to_opp_volt(u32 svsb_volt, u32 svsb_volt_step, > + u32 svsb_volt_base) > +{ > + u32 opp_u_volt; > + > + opp_u_volt = (svsb_volt * svsb_volt_step) + svsb_volt_base; > + > + return opp_u_volt; return (svsb_volt * svsb_volt_step) + svsb_volt_base; > +} > + > +static int svs_get_bank_zone_temperature(u8 *tzone_name, int *tzone_temp) `const char *tzone_name` is probably more appropriate. > +{ > + struct thermal_zone_device *tzd; > + > + tzd = thermal_zone_get_zone_by_name(tzone_name); > + if (IS_ERR(tzd)) > + return PTR_ERR(tzd); > + > + return thermal_zone_get_temp(tzd, tzone_temp); > +} > + > +static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update) > +{ > + int tzone_temp, ret = -EPERM; No need to initialize ret. > + u32 i, svsb_volt, opp_volt, temp_offset = 0; > + > + mutex_lock(&svsb->lock); > + > + /* > + * If svs bank is suspended, it means signed-off voltages are applied. > + * Don't need to update opp voltage anymore. > + */ > + if (svsb->suspended && !force_update) { > + dev_notice(svsb->dev, "bank is suspended\n"); > + ret = -EPERM; > + goto unlock_mutex; > + } > + > + /* Get thermal effect */ > + if (svsb->phase == SVSB_PHASE_MON) { > + if (svsb->temp > svsb->temp_upper_bound && > + svsb->temp < svsb->temp_lower_bound) { > + dev_warn(svsb->dev, "svsb temp = 0x%x?\n", svsb->temp); > + ret = -EINVAL; > + goto unlock_mutex; > + } > + > + ret = svs_get_bank_zone_temperature(svsb->tzone_name, > + &tzone_temp); > + if (ret) { > + dev_err(svsb->dev, "no \"%s\"?(%d)?\n", > + svsb->tzone_name, ret); > + dev_err(svsb->dev, "set signed-off voltage\n"); Please merge the error message in one line (I'm not sure what "set signed-off voltage" means here). > + svsb->phase = SVSB_PHASE_ERROR; > + } > + > + if (tzone_temp >= svsb->tzone_high_temp) > + temp_offset += svsb->tzone_high_temp_offset; > + else if (tzone_temp <= svsb->tzone_low_temp) > + temp_offset += svsb->tzone_low_temp_offset; > + } > + > + /* vmin <= svsb_volt (opp_volt) <= signed-off voltage */ > + for (i = 0; i < svsb->opp_count; i++) { > + if (svsb->phase == SVSB_PHASE_MON) { > + svsb_volt = max((svsb->volts[i] + svsb->volt_offset + > + temp_offset), svsb->vmin); parentheses inside the max parameter not needed > + opp_volt = svs_bank_volt_to_opp_volt(svsb_volt, > + svsb->volt_step, > + svsb->volt_base); > + } else if (svsb->phase == SVSB_PHASE_INIT02) { > + svsb_volt = max((svsb->volts[i] + svsb->volt_offset), > + svsb->vmin); ditto. > + opp_volt = svs_bank_volt_to_opp_volt(svsb_volt, > + svsb->volt_step, > + svsb->volt_base); > + } else if (svsb->phase == SVSB_PHASE_ERROR) { > + opp_volt = svsb->opp_volts[i]; > + } else { > + dev_err(svsb->dev, "unknown phase: %u?\n", svsb->phase); > + ret = -EINVAL; > + goto unlock_mutex; > + } > + > + opp_volt = min(opp_volt, svsb->opp_volts[i]); > + ret = dev_pm_opp_adjust_voltage(svsb->opp_dev, > + svsb->opp_freqs[i], > + opp_volt, opp_volt, > + svsb->opp_volts[i]); > + if (ret) { > + dev_err(svsb->dev, "set voltage fail: %d\n", ret); > + goto unlock_mutex; > + } > + } > + > +unlock_mutex: > + mutex_unlock(&svsb->lock); > + > + return ret; > +} > + > +static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx) > +{ > + u32 vy; > + > + if (v0 == v1 || f0 == f1) > + return v0; > + > + /* *100 to have decimal fraction factor, +99 for rounding up. */ > + vy = (v0 * 100) - ((((v0 - v1) * 100) / (f0 - f1)) * (f0 - fx)); > + vy = (vy + 99) / 100; vy = DIV_ROUND_UP(vy, 100); > + > + return vy; > +} > + > +static void svs_get_vops_v2(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb = svsp->pbank; > + u32 temp, i; > + > + temp = svs_readl(svsp, VOP74); > + svsb->volts[14] = (temp >> 24) & GENMASK(7, 0); > + svsb->volts[12] = (temp >> 16) & GENMASK(7, 0); > + svsb->volts[10] = (temp >> 8) & GENMASK(7, 0); > + svsb->volts[8] = (temp & GENMASK(7, 0)); > + > + temp = svs_readl(svsp, VOP30); > + svsb->volts[6] = (temp >> 24) & GENMASK(7, 0); > + svsb->volts[4] = (temp >> 16) & GENMASK(7, 0); > + svsb->volts[2] = (temp >> 8) & GENMASK(7, 0); > + svsb->volts[0] = (temp & GENMASK(7, 0)); > + > + for (i = 0; i <= 7; i++) { > + if (i < 7) { > + svsb->volts[(i * 2) + 1] = > + interpolate(svsb->freqs_pct[i * 2], > + svsb->freqs_pct[(i + 1) * 2], > + svsb->volts[i * 2], > + svsb->volts[(i + 1) * 2], > + svsb->freqs_pct[(i * 2) + 1]); > + } else if (i == 7) { > + svsb->volts[(i * 2) + 1] = > + interpolate(svsb->freqs_pct[(i - 1) * 2], > + svsb->freqs_pct[i * 2], > + svsb->volts[(i - 1) * 2], > + svsb->volts[i * 2], > + svsb->freqs_pct[(i * 2) + 1]); > + } > + } Please double-check, but I think we can do: for (i = 0; i <= 12; i += 2) { svsb->volts[i + 1] = interpolate(svsb->freqs_pct[i], svsb->freqs_pct[i + 2], svsb->volts[i], svsb->volts[i + 2], svsb->freqs_pct[i + 1]); } svsb->volts[i + 1] = interpolate(svsb->freqs_pct[i - 2], svsb->freqs_pct[i], svsb->volts[i - 2], svsb->volts[i], svsb->freqs_pct[i + 1]); (or maybe replace i with 14 in the computation for this last iteration. > +} > + > +static void svs_set_freqs_pct_v2(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb = svsp->pbank; > + > + svs_writel(svsp, > + ((svsb->freqs_pct[14] << 24) & GENMASK(31, 24)) | Well you already took care of making sure freqs_pct does not have more than 8 bits set, so I don't think you need GENMASK(31, 24). > + ((svsb->freqs_pct[12] << 16) & GENMASK(23, 16)) | > + ((svsb->freqs_pct[10] << 8) & GENMASK(15, 8)) | > + ((svsb->freqs_pct[8]) & GENMASK(7, 0)), > + FREQPCT74); > + > + svs_writel(svsp, > + ((svsb->freqs_pct[6] << 24) & GENMASK(31, 24)) | > + ((svsb->freqs_pct[4] << 16) & GENMASK(23, 16)) | > + ((svsb->freqs_pct[2] << 8) & GENMASK(15, 8)) | > + (svsb->freqs_pct[0] & GENMASK(7, 0)), > + FREQPCT30); > +} > + > +static void svs_set_bank_phase(struct svs_platform *svsp, u32 target_phase) > +{ > + struct svs_bank *svsb = svsp->pbank; > + u32 des_char, temp_char, det_char, limit_vals; > + u32 init2vals, ts_calcs, val, filter, i; > + > + svs_switch_bank(svsp); > + > + des_char = ((svsb->bdes << 8) & GENMASK(15, 8)) | > + (svsb->mdes & GENMASK(7, 0)); Similar to my suggestion about, consider chaging bdes type to u8 so you don't need all these masks? > + svs_writel(svsp, des_char, DESCHAR); > + > + temp_char = ((svsb->vco << 16) & GENMASK(23, 16)) | > + ((svsb->mtdes << 8) & GENMASK(15, 8)) | > + (svsb->dvt_fixed & GENMASK(7, 0)); > + svs_writel(svsp, temp_char, TEMPCHAR); > + > + det_char = ((svsb->dcbdet << 8) & GENMASK(15, 8)) | > + (svsb->dcmdet & GENMASK(7, 0)); > + svs_writel(svsp, det_char, DETCHAR); > + > + svs_writel(svsp, svsb->dc_config, DCCONFIG); > + svs_writel(svsp, svsb->age_config, AGECONFIG); > + > + if (!svsb->agem) { > + svs_writel(svsp, SVSB_RUNCONFIG_DEFAULT, RUNCONFIG); > + } else { > + val = 0x0; > + > + for (i = 0; i < 24; i += 2) { > + filter = 0x3 << i; > + > + if (!(svsb->age_config & filter)) > + val |= (0x1 << i); > + else > + val |= (svsb->age_config & filter); > + } > + svs_writel(svsp, val, RUNCONFIG); > + } > + > + svsp->set_freqs_pct(svsp); > + > + limit_vals = ((svsb->vmax << 24) & GENMASK(31, 24)) | > + ((svsb->vmin << 16) & GENMASK(23, 16)) | > + ((svsb->dthi << 8) & GENMASK(15, 8)) | > + (svsb->dtlo & GENMASK(7, 0)); > + svs_writel(svsp, limit_vals, LIMITVALS); > + svs_writel(svsp, (svsb->vboot & GENMASK(7, 0)), VBOOT); > + svs_writel(svsp, (svsb->det_window & GENMASK(15, 0)), DETWINDOW); > + svs_writel(svsp, (svsb->det_max & GENMASK(15, 0)), CONFIG); > + > + if (svsb->chk_shift) > + svs_writel(svsp, (svsb->chk_shift & GENMASK(7, 0)), CHKSHIFT); > + > + if (svsb->ctl0) > + svs_writel(svsp, svsb->ctl0, CTL0); > + > + svs_writel(svsp, SVSB_INTSTS_CLEAN, INTSTS); > + > + switch (target_phase) { > + case SVSB_PHASE_INIT01: > + svs_writel(svsp, SVSB_INTEN_INIT0x, INTEN); > + svs_writel(svsp, SVSB_EN_INIT01, SVSEN); > + break; > + case SVSB_PHASE_INIT02: > + svs_writel(svsp, SVSB_INTEN_INIT0x, INTEN); > + init2vals = ((svsb->age_voffset_in << 16) & GENMASK(31, 16)) | > + (svsb->dc_voffset_in & GENMASK(15, 0)); > + svs_writel(svsp, init2vals, INIT2VALS); > + svs_writel(svsp, SVSB_EN_INIT02, SVSEN); > + break; > + case SVSB_PHASE_MON: > + ts_calcs = ((svsb->bts << 12) & GENMASK(23, 12)) | > + (svsb->mts & GENMASK(11, 0)); > + svs_writel(svsp, ts_calcs, TSCALCS); > + svs_writel(svsp, SVSB_INTEN_MONVOPEN, INTEN); > + svs_writel(svsp, SVSB_EN_MON, SVSEN); > + break; > + default: > + WARN_ON(1); > + break; > + } > +} > + > +static inline void svs_init01_isr_handler(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb = svsp->pbank; > + > + dev_info(svsb->dev, "%s: VDN74~30:0x%08x~0x%08x, DC:0x%08x\n", dev_dbg? > + __func__, svs_readl(svsp, VDESIGN74), > + svs_readl(svsp, VDESIGN30), svs_readl(svsp, DCVALUES)); > + > + svsb->phase = SVSB_PHASE_INIT01; > + svsb->dc_voffset_in = ~(svs_readl(svsp, DCVALUES) & GENMASK(15, 0)) + 1; > + if (svsb->init01_volt_flag == SVSB_INIT01_VOLT_IGNORE) > + svsb->dc_voffset_in = 0; > + else if ((svsb->dc_voffset_in & SVSB_DC_SIGNED_BIT) && > + (svsb->init01_volt_flag == SVSB_INIT01_VOLT_INC_ONLY)) > + svsb->dc_voffset_in = 0; Merge these 2 if tests into one, since you do the same operation in both cases. > + > + svsb->age_voffset_in = svs_readl(svsp, AGEVALUES) & GENMASK(15, 0); > + > + svs_writel(svsp, SVSB_EN_OFF, SVSEN); > + svs_writel(svsp, SVSB_INTSTS_COMPLETE, INTSTS); > + > + /* svs init01 clock gating */ > + svsb->core_sel &= ~SVSB_INIT01_CLK_EN; > +} > + > +static inline void svs_init02_isr_handler(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb = svsp->pbank; > + > + dev_info(svsb->dev, "%s: VOP74~30:0x%08x~0x%08x, DC:0x%08x\n", > + __func__, svs_readl(svsp, VOP74), svs_readl(svsp, VOP30), > + svs_readl(svsp, DCVALUES)); dev_dbg? > + > + svsb->phase = SVSB_PHASE_INIT02; > + svsp->get_vops(svsp); > + > + svs_writel(svsp, SVSB_EN_OFF, SVSEN); > + svs_writel(svsp, SVSB_INTSTS_COMPLETE, INTSTS); > +} > + > +static inline void svs_mon_mode_isr_handler(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb = svsp->pbank; > + > + svsb->phase = SVSB_PHASE_MON; > + svsb->temp = svs_readl(svsp, TEMP) & GENMASK(7, 0); > + svsp->get_vops(svsp); > + > + svs_writel(svsp, SVSB_INTSTS_MONVOP, INTSTS); > +} > + > +static inline void svs_error_isr_handler(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb = svsp->pbank; > + > + dev_err(svsb->dev, "%s: CORESEL = 0x%08x\n", > + __func__, svs_readl(svsp, CORESEL)); > + dev_err(svsb->dev, "SVSEN = 0x%08x, INTSTS = 0x%08x\n", > + svs_readl(svsp, SVSEN), svs_readl(svsp, INTSTS)); > + dev_err(svsb->dev, "SMSTATE0 = 0x%08x, SMSTATE1 = 0x%08x\n", > + svs_readl(svsp, SMSTATE0), svs_readl(svsp, SMSTATE1)); > + dev_err(svsb->dev, "TEMP = 0x%08x\n", svs_readl(svsp, TEMP)); > + > + svsb->mode_support = SVSB_MODE_ALL_DISABLE; > + svsb->phase = SVSB_PHASE_ERROR; > + > + svs_writel(svsp, SVSB_EN_OFF, SVSEN); > + svs_writel(svsp, SVSB_INTSTS_CLEAN, INTSTS); > +} > + > +static irqreturn_t svs_isr(int irq, void *data) > +{ > + struct svs_platform *svsp = (struct svs_platform *)data; cast not needed. > + struct svs_bank *svsb = NULL; > + unsigned long flags; > + u32 idx, int_sts, svs_en; > + > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + > + spin_lock_irqsave(&mtk_svs_lock, flags); > + svsp->pbank = svsb; > + > + /* Find out which svs bank fires interrupt */ > + if (svsb->int_st & svs_readl(svsp, INTST)) { > + spin_unlock_irqrestore(&mtk_svs_lock, flags); > + continue; > + } > + > + if (!svsb->suspended) { > + svs_switch_bank(svsp); > + int_sts = svs_readl(svsp, INTSTS); > + svs_en = svs_readl(svsp, SVSEN); > + > + if (int_sts == SVSB_INTSTS_COMPLETE && > + ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT01)) > + svs_init01_isr_handler(svsp); > + else if ((int_sts == SVSB_INTSTS_COMPLETE) && > + ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT02)) > + svs_init02_isr_handler(svsp); > + else if (!!(int_sts & SVSB_INTSTS_MONVOP)) !! is not required. > + svs_mon_mode_isr_handler(svsp); > + else > + svs_error_isr_handler(svsp); > + } > + > + spin_unlock_irqrestore(&mtk_svs_lock, flags); > + break; > + } This will panic if svsb is NULL, is that ok or do you want to catch that? > + > + if (svsb->phase != SVSB_PHASE_INIT01) > + svs_adjust_pm_opp_volts(svsb, false); > + > + if (svsb->phase == SVSB_PHASE_INIT01 || > + svsb->phase == SVSB_PHASE_INIT02) > + complete(&svsb->init_completion); > + > + return IRQ_HANDLED; > +} > + > +static void svs_mon_mode(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb; > + unsigned long flags; > + u32 idx; > + > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + > + if (!(svsb->mode_support & SVSB_MODE_MON)) > + continue; > + > + spin_lock_irqsave(&mtk_svs_lock, flags); > + svsp->pbank = svsb; > + svs_set_bank_phase(svsp, SVSB_PHASE_MON); > + spin_unlock_irqrestore(&mtk_svs_lock, flags); > + } > +} > + > +static int svs_init02(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb; > + unsigned long flags, time_left; > + u32 idx; > + > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + > + if (!(svsb->mode_support & SVSB_MODE_INIT02)) > + continue; > + > + reinit_completion(&svsb->init_completion); > + spin_lock_irqsave(&mtk_svs_lock, flags); > + svsp->pbank = svsb; > + svs_set_bank_phase(svsp, SVSB_PHASE_INIT02); > + spin_unlock_irqrestore(&mtk_svs_lock, flags); > + > + time_left = > + wait_for_completion_timeout(&svsb->init_completion, > + msecs_to_jiffies(2000)); > + if (!time_left) { > + dev_err(svsb->dev, "init02 completion timeout\n"); > + return -EBUSY; > + } > + } > + > + return 0; > +} > + > +static int svs_init01(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb; > + struct pm_qos_request *qos_request; > + unsigned long flags, time_left; > + bool search_done, does_svsb_set_pd_on; > + int ret = 0; > + u32 opp_freqs, opp_vboot, buck_volt, idx, i; > + > + qos_request = kzalloc(sizeof(*qos_request), GFP_KERNEL); > + if (!qos_request) > + return -ENOMEM; > + > + /* Let CPUs leave idle-off state for initializing svs_init01. */ > + cpu_latency_qos_add_request(qos_request, 0); > + > + /* > + * Sometimes two svs banks use the same buck. > + * Therefore, we set each svs bank to vboot voltage first. > + */ > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + > + if (!(svsb->mode_support & SVSB_MODE_INIT01)) > + continue; > + > + search_done = false; > + does_svsb_set_pd_on = false; > + > + if (regulator_set_mode(svsb->buck, REGULATOR_MODE_FAST)) > + dev_notice(svsb->dev, "set fast mode fail\n"); > + > + if (svsb->pd_req) { > + ret = regulator_enable(svsb->buck); > + if (ret) { > + dev_err(svsb->dev, "\"%s\" enable fail: %d\n", > + svsb->buck_name, ret); > + goto init01_finish; > + } > + > + if (!pm_runtime_enabled(svsb->pd_dev)) { > + pm_runtime_enable(svsb->pd_dev); > + does_svsb_set_pd_on = true; > + } > + > + ret = pm_runtime_get_sync(svsb->pd_dev); > + if (ret < 0) { > + dev_err(svsb->dev, "mtcmos on fail: %d\n", > + ret); > + goto init01_finish; > + } > + } > + > + /* > + * Find the fastest freq that can be run at vboot and > + * fix to that freq until svs_init01 is done. > + */ > + opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot, > + svsb->volt_step, > + svsb->volt_base); > + > + for (i = 0; i < svsb->opp_count; i++) { > + opp_freqs = svsb->opp_freqs[i]; > + if (!search_done && svsb->opp_volts[i] <= opp_vboot) { > + ret = dev_pm_opp_adjust_voltage(svsb->opp_dev, > + opp_freqs, > + opp_vboot, > + opp_vboot, > + opp_vboot); > + if (ret) { > + dev_err(svsb->dev, > + "set voltage fail: %d\n", ret); > + goto init01_finish; > + } > + > + search_done = true; > + } else { > + dev_pm_opp_disable(svsb->opp_dev, > + svsb->opp_freqs[i]); > + } > + } > + } > + > + /* svs bank init01 begins */ > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + > + if (!(svsb->mode_support & SVSB_MODE_INIT01)) > + continue; > + > + opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot, > + svsb->volt_step, > + svsb->volt_base); > + > + buck_volt = regulator_get_voltage(svsb->buck); > + if (buck_volt != opp_vboot) { > + dev_err(svsb->dev, > + "buck voltage: %u, expected vboot: %u\n", > + buck_volt, opp_vboot); > + ret = -EPERM; > + goto init01_finish; > + } > + > + spin_lock_irqsave(&mtk_svs_lock, flags); > + svsp->pbank = svsb; > + svs_set_bank_phase(svsp, SVSB_PHASE_INIT01); > + spin_unlock_irqrestore(&mtk_svs_lock, flags); > + > + time_left = > + wait_for_completion_timeout(&svsb->init_completion, > + msecs_to_jiffies(2000)); > + if (!time_left) { > + dev_err(svsb->dev, "init01 completion timeout\n"); > + ret = -EBUSY; > + goto init01_finish; > + } > + } > + > +init01_finish: > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + > + if (!(svsb->mode_support & SVSB_MODE_INIT01)) > + continue; > + > + for (i = 0; i < svsb->opp_count; i++) > + dev_pm_opp_enable(svsb->opp_dev, svsb->opp_freqs[i]); > + > + if (regulator_set_mode(svsb->buck, REGULATOR_MODE_NORMAL)) > + dev_notice(svsb->dev, "fail to set normal mode\n"); > + > + if (svsb->pd_req) { > + if (pm_runtime_put_sync(svsb->pd_dev)) > + dev_err(svsb->dev, "mtcmos off fail\n"); > + > + if (does_svsb_set_pd_on) { > + pm_runtime_disable(svsb->pd_dev); > + does_svsb_set_pd_on = false; > + } > + > + if (regulator_disable(svsb->buck)) > + dev_err(svsb->dev, "disable power fail\n"); > + } > + } > + > + cpu_latency_qos_remove_request(qos_request); > + kfree(qos_request); > + > + return ret; > +} > + > +static int svs_start(struct svs_platform *svsp) > +{ > + int ret; > + > + ret = svs_init01(svsp); > + if (ret) > + return ret; > + > + ret = svs_init02(svsp); > + if (ret) > + return ret; > + > + svs_mon_mode(svsp); > + > + return ret; Or just return 0; > +} > + > +static struct device *svs_get_subsys_device(struct svs_platform *svsp, > + u8 *node_name) > +{ > + struct platform_device *pdev; > + struct device_node *np; > + > + np = of_find_node_by_name(NULL, node_name); > + if (!np) { > + dev_err(svsp->dev, "cannot find %s node\n", node_name); > + return ERR_PTR(-ENODEV); > + } > + > + pdev = of_find_device_by_node(np); > + if (!pdev) { > + of_node_put(np); > + dev_err(svsp->dev, "cannot find pdev by %s\n", node_name); > + return ERR_PTR(-ENXIO); > + } > + > + of_node_put(np); > + > + return &pdev->dev; > +} > + > +static struct device *svs_add_device_link(struct svs_platform *svsp, > + u8 *node_name) > +{ > + struct device *dev; > + struct device_link *sup_link; > + > + if (!node_name) { > + dev_err(svsp->dev, "node name cannot be null\n"); > + return ERR_PTR(-EINVAL); > + } > + > + dev = svs_get_subsys_device(svsp, node_name); > + if (IS_ERR(dev)) > + return dev; > + > + sup_link = device_link_add(svsp->dev, dev, > + DL_FLAG_AUTOREMOVE_CONSUMER); > + > + if (sup_link->status == DL_STATE_DORMANT) > + return ERR_PTR(-EPROBE_DEFER); > + > + return dev; > +} > + > +static int svs_resource_setup(struct svs_platform *svsp) > +{ > + struct svs_bank *svsb; > + struct dev_pm_opp *opp; > + unsigned long freq; > + int count, ret; > + u32 idx, i; > + > + dev_set_drvdata(svsp->dev, svsp); > + > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + > + switch (svsb->sw_id) { > + case SVSB_CPU_LITTLE: > + svsb->name = "SVSB_CPU_LITTLE"; > + break; > + case SVSB_CPU_BIG: > + svsb->name = "SVSB_CPU_BIG"; > + break; > + case SVSB_CCI: > + svsb->name = "SVSB_CCI"; > + break; > + case SVSB_GPU: > + svsb->name = "SVSB_GPU"; > + break; > + default: > + WARN_ON(1); > + return -EINVAL; > + } > + > + svsb->dev = devm_kzalloc(svsp->dev, sizeof(*svsb->dev), > + GFP_KERNEL); > + if (!svsb->dev) > + return -ENOMEM; > + > + ret = dev_set_name(svsb->dev, svsb->name); > + if (ret) > + return ret; > + > + dev_set_drvdata(svsb->dev, svsp); > + > + ret = dev_pm_opp_of_add_table(svsb->opp_dev); > + if (ret) { > + dev_err(svsb->dev, "add opp table fail: %d\n", ret); > + return ret; > + } > + > + mutex_init(&svsb->lock); > + init_completion(&svsb->init_completion); > + > + svsb->buck = devm_regulator_get_optional(svsb->opp_dev, > + svsb->buck_name); > + if (IS_ERR(svsb->buck)) { > + dev_err(svsb->dev, "cannot get \"%s-supply\"\n", > + svsb->buck_name); > + return PTR_ERR(svsb->buck); > + } > + > + count = dev_pm_opp_get_opp_count(svsb->opp_dev); > + if (svsb->opp_count != count) { > + dev_err(svsb->dev, > + "opp_count not \"%u\" but get \"%d\"?\n", > + svsb->opp_count, count); > + return count; > + } > + > + for (i = 0, freq = U32_MAX; i < svsb->opp_count; i++, freq--) { > + opp = dev_pm_opp_find_freq_floor(svsb->opp_dev, &freq); > + if (IS_ERR(opp)) { > + dev_err(svsb->dev, "cannot find freq = %ld\n", > + PTR_ERR(opp)); > + return PTR_ERR(opp); > + } > + > + svsb->opp_freqs[i] = freq; > + svsb->opp_volts[i] = dev_pm_opp_get_voltage(opp); > + svsb->freqs_pct[i] = percent(svsb->opp_freqs[i], > + svsb->freq_base); > + dev_pm_opp_put(opp); > + } > + } > + > + return 0; > +} > + > +static bool svs_mt8183_efuse_parsing(struct svs_platform *svsp) > +{ > + struct thermal_parameter tp; > + struct svs_bank *svsb; > + bool mon_mode_support = true; > + int format[6], x_roomt[6], tb_roomt = 0; > + struct nvmem_cell *cell; > + u32 idx, i, ft_pgm, mts, temp0, temp1, temp2; > + > + if (svsp->fake_efuse) { > + pr_notice("fake efuse\n"); > + svsp->efuse[0] = 0x00310080; > + svsp->efuse[1] = 0xabfbf757; > + svsp->efuse[2] = 0x47c747c7; > + svsp->efuse[3] = 0xabfbf757; > + svsp->efuse[4] = 0xe7fca0ec; > + svsp->efuse[5] = 0x47bf4b88; > + svsp->efuse[6] = 0xabfb8fa5; > + svsp->efuse[7] = 0xabfb217b; > + svsp->efuse[8] = 0x4bf34be1; > + svsp->efuse[9] = 0xabfb670d; > + svsp->efuse[16] = 0xabfbc653; > + svsp->efuse[17] = 0x47f347e1; > + svsp->efuse[18] = 0xabfbd848; > + } Looks like debugging code, drop this? > + > + for (i = 0; i < svsp->efuse_num; i++) > + if (svsp->efuse[i]) > + dev_notice(svsp->dev, "M_HW_RES%d: 0x%08x\n", > + i, svsp->efuse[i]); dev_dbg? > + > + /* Svs efuse parsing */ > + ft_pgm = (svsp->efuse[0] >> 4) & GENMASK(3, 0); > + > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + > + if (ft_pgm <= 1) > + svsb->init01_volt_flag = SVSB_INIT01_VOLT_IGNORE; > + > + switch (svsb->sw_id) { > + case SVSB_CPU_LITTLE: > + svsb->bdes = svsp->efuse[16] & GENMASK(7, 0); > + svsb->mdes = (svsp->efuse[16] >> 8) & GENMASK(7, 0); > + svsb->dcbdet = (svsp->efuse[16] >> 16) & GENMASK(7, 0); > + svsb->dcmdet = (svsp->efuse[16] >> 24) & GENMASK(7, 0); > + svsb->mtdes = (svsp->efuse[17] >> 16) & GENMASK(7, 0); Again, if all of those values were u8, there'd be no need for these GENMASK > + > + if (ft_pgm <= 3) > + svsb->volt_offset += 10; > + else > + svsb->volt_offset += 2; > + break; > + case SVSB_CPU_BIG: > + svsb->bdes = svsp->efuse[18] & GENMASK(7, 0); > + svsb->mdes = (svsp->efuse[18] >> 8) & GENMASK(7, 0); > + svsb->dcbdet = (svsp->efuse[18] >> 16) & GENMASK(7, 0); > + svsb->dcmdet = (svsp->efuse[18] >> 24) & GENMASK(7, 0); > + svsb->mtdes = svsp->efuse[17] & GENMASK(7, 0); > + > + if (ft_pgm <= 3) > + svsb->volt_offset += 15; > + else > + svsb->volt_offset += 12; > + break; > + case SVSB_CCI: > + svsb->bdes = svsp->efuse[4] & GENMASK(7, 0); > + svsb->mdes = (svsp->efuse[4] >> 8) & GENMASK(7, 0); > + svsb->dcbdet = (svsp->efuse[4] >> 16) & GENMASK(7, 0); > + svsb->dcmdet = (svsp->efuse[4] >> 24) & GENMASK(7, 0); > + svsb->mtdes = (svsp->efuse[5] >> 16) & GENMASK(7, 0); > + > + if (ft_pgm <= 3) > + svsb->volt_offset += 10; > + else > + svsb->volt_offset += 2; > + break; > + case SVSB_GPU: > + svsb->bdes = svsp->efuse[6] & GENMASK(7, 0); > + svsb->mdes = (svsp->efuse[6] >> 8) & GENMASK(7, 0); > + svsb->dcbdet = (svsp->efuse[6] >> 16) & GENMASK(7, 0); > + svsb->dcmdet = (svsp->efuse[6] >> 24) & GENMASK(7, 0); > + svsb->mtdes = svsp->efuse[5] & GENMASK(7, 0); > + > + if (ft_pgm >= 2) { > + svsb->freq_base = 800000000; /* 800MHz */ > + svsb->dvt_fixed = 2; > + } > + break; > + default: > + break; > + } > + } > + > + /* Get thermal efuse by nvmem */ > + cell = nvmem_cell_get(svsp->dev, "t-calibration-data"); > + if (IS_ERR_OR_NULL(cell)) { > + dev_err(svsp->dev, "no thermal cell, no mon mode\n"); > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + svsb->mode_support &= ~SVSB_MODE_MON; > + } > + > + return true; > + } > + > + svsp->tefuse = (u32 *)nvmem_cell_read(cell, &svsp->tefuse_num); Cast not needed. Also, this need to be freed somewhere in remove code (kfree(svsp->tefuse)). And it seems like svsp->tefuse is only used in this function, can you just allocate it here? > + svsp->tefuse_num /= sizeof(u32); > + nvmem_cell_put(cell); > + > + if (svsp->fake_efuse) { > + svsp->tefuse[0] = 0x02873f69; > + svsp->tefuse[1] = 0xa11d9142; > + svsp->tefuse[2] = 0xa2526900; > + } > + > + /* Thermal efuse parsing */ > + tp.adc_ge_t = (svsp->tefuse[1] >> 22) & GENMASK(9, 0); > + tp.adc_oe_t = (svsp->tefuse[1] >> 12) & GENMASK(9, 0); > + > + tp.o_vtsmcu1 = (svsp->tefuse[0] >> 17) & GENMASK(8, 0); > + tp.o_vtsmcu2 = (svsp->tefuse[0] >> 8) & GENMASK(8, 0); > + tp.o_vtsmcu3 = svsp->tefuse[1] & GENMASK(8, 0); > + tp.o_vtsmcu4 = (svsp->tefuse[2] >> 23) & GENMASK(8, 0); > + tp.o_vtsmcu5 = (svsp->tefuse[2] >> 5) & GENMASK(8, 0); > + tp.o_vtsabb = (svsp->tefuse[2] >> 14) & GENMASK(8, 0); > + > + tp.degc_cali = (svsp->tefuse[0] >> 1) & GENMASK(5, 0); > + tp.adc_cali_en_t = svsp->tefuse[0] & BIT(0); > + tp.o_slope_sign = (svsp->tefuse[0] >> 7) & BIT(0); > + > + tp.ts_id = (svsp->tefuse[1] >> 9) & BIT(0); > + tp.o_slope = (svsp->tefuse[0] >> 26) & GENMASK(5, 0); > + > + if (tp.adc_cali_en_t == 1) { > + if (!tp.ts_id) > + tp.o_slope = 0; > + > + if ((tp.adc_ge_t < 265 || tp.adc_ge_t > 758) || > + (tp.adc_oe_t < 265 || tp.adc_oe_t > 758) || > + (tp.o_vtsmcu1 < -8 || tp.o_vtsmcu1 > 484) || > + (tp.o_vtsmcu2 < -8 || tp.o_vtsmcu2 > 484) || > + (tp.o_vtsmcu3 < -8 || tp.o_vtsmcu3 > 484) || > + (tp.o_vtsmcu4 < -8 || tp.o_vtsmcu4 > 484) || > + (tp.o_vtsmcu5 < -8 || tp.o_vtsmcu5 > 484) || > + (tp.o_vtsabb < -8 || tp.o_vtsabb > 484) || > + (tp.degc_cali < 1 || tp.degc_cali > 63)) { > + dev_err(svsp->dev, "bad thermal efuse, no mon mode\n"); > + mon_mode_support = false; > + } > + } else { > + dev_err(svsp->dev, "no thermal efuse, no mon mode\n"); > + mon_mode_support = false; > + } > + > + if (!mon_mode_support) { > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + svsb->mode_support &= ~SVSB_MODE_MON; > + } > + > + return true; > + } > + > + tp.ge = ((tp.adc_ge_t - 512) * 10000) / 4096; > + tp.oe = (tp.adc_oe_t - 512); > + tp.gain = (10000 + tp.ge); > + > + format[0] = (tp.o_vtsmcu1 + 3350 - tp.oe); > + format[1] = (tp.o_vtsmcu2 + 3350 - tp.oe); > + format[2] = (tp.o_vtsmcu3 + 3350 - tp.oe); > + format[3] = (tp.o_vtsmcu4 + 3350 - tp.oe); > + format[4] = (tp.o_vtsmcu5 + 3350 - tp.oe); > + format[5] = (tp.o_vtsabb + 3350 - tp.oe); > + > + for (i = 0; i < 6; i++) > + x_roomt[i] = (((format[i] * 10000) / 4096) * 10000) / tp.gain; > + > + temp0 = (10000 * 100000 / tp.gain) * 15 / 18; > + > + if (!tp.o_slope_sign) > + mts = (temp0 * 10) / (1534 + tp.o_slope * 10); > + else > + mts = (temp0 * 10) / (1534 - tp.o_slope * 10); > + > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + svsb->mts = mts; > + > + switch (svsb->sw_id) { > + case SVSB_CPU_LITTLE: > + tb_roomt = x_roomt[3]; > + break; > + case SVSB_CPU_BIG: > + tb_roomt = x_roomt[4]; > + break; > + case SVSB_CCI: > + tb_roomt = x_roomt[3]; > + break; > + case SVSB_GPU: > + tb_roomt = x_roomt[1]; > + break; > + default: > + break; > + } > + > + temp0 = (tp.degc_cali * 10 / 2); > + temp1 = ((10000 * 100000 / 4096 / tp.gain) * > + tp.oe + tb_roomt * 10) * 15 / 18; > + > + if (!tp.o_slope_sign) > + temp2 = temp1 * 100 / (1534 + tp.o_slope * 10); > + else > + temp2 = temp1 * 100 / (1534 - tp.o_slope * 10); > + > + svsb->bts = (temp0 + temp2 - 250) * 4 / 10; > + } > + > + return true; > +} > + > +static bool svs_is_supported(struct svs_platform *svsp) > +{ > + struct nvmem_cell *cell; > + > + /* Get svs efuse by nvmem */ > + cell = nvmem_cell_get(svsp->dev, "svs-calibration-data"); > + if (IS_ERR_OR_NULL(cell)) { > + dev_err(svsp->dev, > + "no \"svs-calibration-data\" from dts? disable svs\n"); > + return false; > + } > + > + svsp->efuse = (u32 *)nvmem_cell_read(cell, &svsp->efuse_num); Similar to tefuse, I think efuse is only used at init time, so maybe it ca be a local variable? > + svsp->efuse_num /= sizeof(u32); > + nvmem_cell_put(cell); > + > + if (!svsp->fake_efuse && !svsp->efuse[svsp->efuse_check]) { > + dev_err(svsp->dev, "svs_efuse[%u] = 0x%x?\n", > + svsp->efuse_check, svsp->efuse[svsp->efuse_check]); > + return false; > + } > + > + return svsp->efuse_parsing(svsp); > +} > + > +static int svs_suspend(struct device *dev) > +{ > + struct svs_platform *svsp = dev_get_drvdata(dev); > + struct svs_bank *svsb; > + unsigned long flags; > + int ret; > + u32 idx; > + > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + > + /* Wait if svs_isr() is still in process. */ > + spin_lock_irqsave(&mtk_svs_lock, flags); > + svsp->pbank = svsb; > + svs_switch_bank(svsp); > + svs_writel(svsp, SVSB_EN_OFF, SVSEN); > + svs_writel(svsp, SVSB_INTSTS_CLEAN, INTSTS); > + spin_unlock_irqrestore(&mtk_svs_lock, flags); > + > + svsb->suspended = true; > + if (svsb->phase != SVSB_PHASE_INIT01) { > + svsb->phase = SVSB_PHASE_ERROR; > + svs_adjust_pm_opp_volts(svsb, true); > + } > + } > + > + if (svsp->rst) { > + ret = reset_control_assert(svsp->rst); > + if (ret) { > + dev_err(svsp->dev, "cannot assert reset %d\n", ret); > + return ret; > + } > + } > + > + clk_disable_unprepare(svsp->main_clk); > + > + return 0; > +} > + > +static int svs_resume(struct device *dev) > +{ > + struct svs_platform *svsp = dev_get_drvdata(dev); > + struct svs_bank *svsb; > + int ret; > + u32 idx; > + > + ret = clk_prepare_enable(svsp->main_clk); > + if (ret) { > + dev_err(svsp->dev, "cannot enable main_clk, disable svs\n"); > + return ret; > + } > + > + if (svsp->rst) { > + ret = reset_control_deassert(svsp->rst); > + if (ret) { > + dev_err(svsp->dev, "cannot deassert reset %d\n", ret); > + return ret; > + } > + } > + > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + svsb->suspended = false; > + } > + > + ret = svs_init02(svsp); > + if (ret) > + return ret; > + > + svs_mon_mode(svsp); > + > + return 0; > +} > + > +static struct svs_bank svs_mt8183_banks[4] = { > + { > + .sw_id = SVSB_CPU_LITTLE, > + .cpu_id = 0, > + .tzone_name = "tzts4", > + .buck_name = "proc", > + .pd_req = false, > + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY, > + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02, > + .opp_count = 16, > + .freq_base = 1989000000, > + .vboot = 0x30, > + .volt_step = 6250, > + .volt_base = 500000, > + .volt_offset = 0, > + .vmax = 0x64, > + .vmin = 0x18, > + .dthi = 0x1, > + .dtlo = 0xfe, > + .det_window = 0xa28, > + .det_max = 0xffff, > + .age_config = 0x555555, > + .agem = 0, > + .dc_config = 0x555555, > + .dvt_fixed = 0x7, > + .vco = 0x10, > + .chk_shift = 0x77, > + .temp_upper_bound = 0x64, > + .temp_lower_bound = 0xb2, > + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX, > + .tzone_low_temp = 25000, > + .tzone_low_temp_offset = 0, > + .core_sel = 0x8fff0000, > + .int_st = BIT(0), > + .ctl0 = 0x00010001, > + }, > + { > + .sw_id = SVSB_CPU_BIG, > + .cpu_id = 4, > + .tzone_name = "tzts5", > + .buck_name = "proc", > + .pd_req = false, > + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY, > + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02, > + .opp_count = 16, > + .freq_base = 1989000000, > + .vboot = 0x30, > + .volt_step = 6250, > + .volt_base = 500000, > + .volt_offset = 0, > + .vmax = 0x58, > + .vmin = 0x10, > + .dthi = 0x1, > + .dtlo = 0xfe, > + .det_window = 0xa28, > + .det_max = 0xffff, > + .age_config = 0x555555, > + .agem = 0, > + .dc_config = 0x555555, > + .dvt_fixed = 0x7, > + .vco = 0x10, > + .chk_shift = 0x77, > + .temp_upper_bound = 0x64, > + .temp_lower_bound = 0xb2, > + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX, > + .tzone_low_temp = 25000, > + .tzone_low_temp_offset = 0, > + .core_sel = 0x8fff0001, > + .int_st = BIT(1), > + .ctl0 = 0x00000001, > + }, > + { > + .sw_id = SVSB_CCI, > + .tzone_name = "tzts4", > + .buck_name = "proc", > + .pd_req = false, > + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY, > + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02, > + .opp_count = 16, > + .freq_base = 1196000000, > + .vboot = 0x30, > + .volt_step = 6250, > + .volt_base = 500000, > + .volt_offset = 0, > + .vmax = 0x64, > + .vmin = 0x18, > + .dthi = 0x1, > + .dtlo = 0xfe, > + .det_window = 0xa28, > + .det_max = 0xffff, > + .age_config = 0x555555, > + .agem = 0, > + .dc_config = 0x555555, > + .dvt_fixed = 0x7, > + .vco = 0x10, > + .chk_shift = 0x77, > + .temp_upper_bound = 0x64, > + .temp_lower_bound = 0xb2, > + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX, > + .tzone_low_temp = 25000, > + .tzone_low_temp_offset = 0, > + .core_sel = 0x8fff0002, > + .int_st = BIT(2), > + .ctl0 = 0x00100003, > + }, > + { > + .sw_id = SVSB_GPU, > + .tzone_name = "tzts2", > + .buck_name = "mali", > + .pd_req = true, > + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY, > + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02 | > + SVSB_MODE_MON, > + .opp_count = 16, > + .freq_base = 900000000, > + .vboot = 0x30, > + .volt_step = 6250, > + .volt_base = 500000, > + .volt_offset = 0, > + .vmax = 0x40, > + .vmin = 0x14, > + .dthi = 0x1, > + .dtlo = 0xfe, > + .det_window = 0xa28, > + .det_max = 0xffff, > + .age_config = 0x555555, > + .agem = 0, > + .dc_config = 0x555555, > + .dvt_fixed = 0x3, > + .vco = 0x10, > + .chk_shift = 0x77, > + .temp_upper_bound = 0x64, > + .temp_lower_bound = 0xb2, > + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX, > + .tzone_low_temp = 25000, > + .tzone_low_temp_offset = 3, > + .core_sel = 0x8fff0003, > + .int_st = BIT(3), > + .ctl0 = 0x00050001, > + }, > +}; > + > +static int svs_get_svs_mt8183_platform_data(struct svs_platform *svsp) > +{ > + struct device *dev; > + struct svs_bank *svsb; > + u32 idx; > + > + svsp->name = "mt8183-svs"; > + svsp->banks = svs_mt8183_banks; > + svsp->efuse_parsing = svs_mt8183_efuse_parsing; > + svsp->set_freqs_pct = svs_set_freqs_pct_v2; > + svsp->get_vops = svs_get_vops_v2; > + svsp->regs = svs_regs_v2; > + svsp->irqflags = IRQF_TRIGGER_LOW | IRQF_ONESHOT; > + svsp->rst = NULL; > + svsp->fake_efuse = false; > + svsp->bank_num = 4; > + svsp->efuse_check = 2; > + > + dev = svs_add_device_link(svsp, "thermal"); > + if (IS_ERR(dev)) > + return PTR_ERR(dev); > + > + for (idx = 0; idx < svsp->bank_num; idx++) { > + svsb = &svsp->banks[idx]; > + > + switch (svsb->sw_id) { > + case SVSB_CPU_LITTLE: > + case SVSB_CPU_BIG: > + svsb->opp_dev = get_cpu_device(svsb->cpu_id); > + break; > + case SVSB_CCI: > + svsb->opp_dev = svs_add_device_link(svsp, "cci"); > + break; > + case SVSB_GPU: > + svsb->opp_dev = svs_add_device_link(svsp, "mali"); > + svsb->pd_dev = svs_add_device_link(svsp, > + "mali_gpu_core2"); > + if (IS_ERR(svsb->pd_dev)) > + return PTR_ERR(svsb->pd_dev); > + break; > + default: > + WARN_ON(1); > + return -EINVAL; > + } > + > + if (IS_ERR(svsb->opp_dev)) > + return PTR_ERR(svsb->opp_dev); > + } > + > + return 0; > +} > + > +static const struct of_device_id mtk_svs_of_match[] = { > + { > + .compatible = "mediatek,mt8183-svs", > + .data = &svs_get_svs_mt8183_platform_data, > + }, { > + /* Sentinel */ > + }, > +}; > + > +static int svs_probe(struct platform_device *pdev) > +{ > + int (*svs_get_svs_platform_data)(struct svs_platform *svsp); > + struct svs_platform *svsp; > + unsigned int svsp_irq; > + int ret; > + > + svsp = devm_kzalloc(&pdev->dev, sizeof(*svsp), GFP_KERNEL); > + if (!svsp) > + return -ENOMEM; > + > + svs_get_svs_platform_data = of_device_get_match_data(&pdev->dev); > + if (!svs_get_svs_platform_data) { > + dev_err(svsp->dev, "no svs platform data? why?\n"); > + return -EPERM; > + } > + > + svsp->dev = &pdev->dev; > + ret = svs_get_svs_platform_data(svsp); > + if (ret) { > + dev_err_probe(svsp->dev, ret, "fail to get svsp data\n"); > + return ret; > + } > + > + if (!svs_is_supported(svsp)) { > + dev_notice(svsp->dev, "svs is not supported\n"); > + return -EPERM; > + } > + > + ret = svs_resource_setup(svsp); > + if (ret) { > + dev_err(svsp->dev, "svs resource setup fail: %d\n", ret); > + return ret; > + } > + > + svsp_irq = irq_of_parse_and_map(svsp->dev->of_node, 0); > + ret = devm_request_threaded_irq(svsp->dev, svsp_irq, NULL, svs_isr, > + svsp->irqflags, svsp->name, svsp); > + if (ret) { > + dev_err(svsp->dev, "register irq(%d) failed: %d\n", > + svsp_irq, ret); > + return ret; > + } > + > + svsp->main_clk = devm_clk_get(svsp->dev, "main"); > + if (IS_ERR(svsp->main_clk)) { > + dev_err(svsp->dev, "failed to get clock: %ld\n", > + PTR_ERR(svsp->main_clk)); > + return PTR_ERR(svsp->main_clk); > + } > + > + ret = clk_prepare_enable(svsp->main_clk); > + if (ret) { > + dev_err(svsp->dev, "cannot enable main clk: %d\n", ret); > + return ret; > + } > + > + svsp->base = of_iomap(svsp->dev->of_node, 0); > + if (IS_ERR_OR_NULL(svsp->base)) { > + dev_err(svsp->dev, "cannot find svs register base\n"); > + ret = -EINVAL; > + goto svs_probe_clk_disable; > + } > + > + ret = svs_start(svsp); > + if (ret) { > + dev_err(svsp->dev, "svs start fail: %d\n", ret); > + goto svs_probe_iounmap; > + } > + > + return 0; > + > +svs_probe_iounmap: > + iounmap(svsp->base); > + > +svs_probe_clk_disable: > + clk_disable_unprepare(svsp->main_clk); > + > + return ret; > +} > + > +static SIMPLE_DEV_PM_OPS(svs_pm_ops, svs_suspend, svs_resume); > + > +static struct platform_driver svs_driver = { > + .probe = svs_probe, > + .driver = { > + .name = "mtk-svs", > + .pm = &svs_pm_ops, > + .of_match_table = of_match_ptr(mtk_svs_of_match), > + }, > +}; > + > +module_platform_driver(svs_driver); > + > +MODULE_AUTHOR("Roger Lu <roger.lu@mediatek.com>"); > +MODULE_DESCRIPTION("MediaTek SVS driver"); > +MODULE_LICENSE("GPL v2"); > -- > 2.18.0 > _______________________________________________ > Linux-mediatek mailing list > Linux-mediatek@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-mediatek
On Mon, Jan 4, 2021 at 4:51 PM Roger Lu <roger.lu@mediatek.com> wrote: > > > Hi Nicolas, > > Thanks for all the advices. > > On Thu, 2020-12-31 at 10:10 +0800, Nicolas Boichat wrote: > > On Sun, Dec 27, 2020 at 6:55 PM Roger Lu <roger.lu@mediatek.com> wrote: [snip] > > > +static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update) > > > +{ > > > + int tzone_temp, ret = -EPERM; > > > > No need to initialize ret. > > Oh, excuse me, some coding check tool warn that this `ret` might return > without being uninitialized. Therefore, I'll keep the initialization. Oh, you're right, there is a possible path where ret is not set. sgtm then. > > > > > > + u32 i, svsb_volt, opp_volt, temp_offset = 0; > > > + > > > + mutex_lock(&svsb->lock); > > > + > > > + /* > > > + * If svs bank is suspended, it means signed-off voltages are applied. > > > + * Don't need to update opp voltage anymore. > > > + */ > > > + if (svsb->suspended && !force_update) { > > > + dev_notice(svsb->dev, "bank is suspended\n"); > > > + ret = -EPERM; > > > + goto unlock_mutex; > > > + } > > > + > > > + /* Get thermal effect */ > > > + if (svsb->phase == SVSB_PHASE_MON) { > > > + if (svsb->temp > svsb->temp_upper_bound && > > > + svsb->temp < svsb->temp_lower_bound) { > > > + dev_warn(svsb->dev, "svsb temp = 0x%x?\n", svsb->temp); > > > + ret = -EINVAL; > > > + goto unlock_mutex; > > > + } > > > + > > > + ret = svs_get_bank_zone_temperature(svsb->tzone_name, > > > + &tzone_temp); > > > + if (ret) { > > > + dev_err(svsb->dev, "no \"%s\"?(%d)?\n", > > > + svsb->tzone_name, ret); > > > + dev_err(svsb->dev, "set signed-off voltage\n"); > > > > Please merge the error message in one line (I'm not sure what "set > > signed-off voltage" means here). > > 1. Ok, I'll merge them. Thanks. > 2. signed-off voltages means CPU DVFS default voltages So just write "default voltages" then? ,-) > > > [snip] > > > +static irqreturn_t svs_isr(int irq, void *data) > > > +{ > > > + struct svs_platform *svsp = (struct svs_platform *)data; > > > > cast not needed. > > Ok, I'll remove it. Thanks. > > > > > > + struct svs_bank *svsb = NULL; > > > + unsigned long flags; > > > + u32 idx, int_sts, svs_en; > > > + > > > + for (idx = 0; idx < svsp->bank_num; idx++) { > > > + svsb = &svsp->banks[idx]; > > > + > > > + spin_lock_irqsave(&mtk_svs_lock, flags); > > > + svsp->pbank = svsb; > > > + > > > + /* Find out which svs bank fires interrupt */ > > > + if (svsb->int_st & svs_readl(svsp, INTST)) { > > > + spin_unlock_irqrestore(&mtk_svs_lock, flags); > > > + continue; > > > + } > > > + > > > + if (!svsb->suspended) { > > > + svs_switch_bank(svsp); > > > + int_sts = svs_readl(svsp, INTSTS); > > > + svs_en = svs_readl(svsp, SVSEN); > > > + > > > + if (int_sts == SVSB_INTSTS_COMPLETE && > > > + ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT01)) > > > + svs_init01_isr_handler(svsp); > > > + else if ((int_sts == SVSB_INTSTS_COMPLETE) && > > > + ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT02)) > > > + svs_init02_isr_handler(svsp); > > > + else if (!!(int_sts & SVSB_INTSTS_MONVOP)) > > > > !! is not required. > > Ok, I'll remove it. Thanks. > > > > > > + svs_mon_mode_isr_handler(svsp); > > > + else > > > + svs_error_isr_handler(svsp); > > > + } > > > + > > > + spin_unlock_irqrestore(&mtk_svs_lock, flags); > > > + break; > > > + } > > > > This will panic if svsb is NULL, is that ok or do you want to catch that? > > Oh, it is fine. Thanks for the heads-up. I should have been stronger in my statement, I think you want to add a BUG_ON(!svsb) to crash in a slightly more predictable manner. [snip] > > > + > > > + svsp->tefuse = (u32 *)nvmem_cell_read(cell, &svsp->tefuse_num); > > > > Cast not needed. > > Ok, I'll remove it if build/test ok. Because nvmem_cell_read returns > (void *). > > > > > Also, this need to be freed somewhere in remove code (kfree(svsp->tefuse)). > > > > And it seems like svsp->tefuse is only used in this function, can you > > just allocate it here? > > Oh, svsp->tefuse will be used in SVS debug patch for debug purpose. So, > I need to save it as struct member. Oh I missed that, sgtm then. Thanks. > [snip]
Hi Nicolas, On Mon, 2021-01-04 at 17:27 +0800, Nicolas Boichat wrote: > On Mon, Jan 4, 2021 at 4:51 PM Roger Lu <roger.lu@mediatek.com> wrote: > > > > > > Hi Nicolas, > > > > Thanks for all the advices. > > > > On Thu, 2020-12-31 at 10:10 +0800, Nicolas Boichat wrote: > > > On Sun, Dec 27, 2020 at 6:55 PM Roger Lu <roger.lu@mediatek.com> wrote: > [snip] > > > > +static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update) > > > > +{ > > > > + int tzone_temp, ret = -EPERM; > > > > > > No need to initialize ret. > > > > Oh, excuse me, some coding check tool warn that this `ret` might return > > without being uninitialized. Therefore, I'll keep the initialization. > > Oh, you're right, there is a possible path where ret is not set. sgtm then. > > > > > > > > > > + u32 i, svsb_volt, opp_volt, temp_offset = 0; > > > > + > > > > + mutex_lock(&svsb->lock); > > > > + > > > > + /* > > > > + * If svs bank is suspended, it means signed-off voltages are applied. > > > > + * Don't need to update opp voltage anymore. > > > > + */ > > > > + if (svsb->suspended && !force_update) { > > > > + dev_notice(svsb->dev, "bank is suspended\n"); > > > > + ret = -EPERM; > > > > + goto unlock_mutex; > > > > + } > > > > + > > > > + /* Get thermal effect */ > > > > + if (svsb->phase == SVSB_PHASE_MON) { > > > > + if (svsb->temp > svsb->temp_upper_bound && > > > > + svsb->temp < svsb->temp_lower_bound) { > > > > + dev_warn(svsb->dev, "svsb temp = 0x%x?\n", svsb->temp); > > > > + ret = -EINVAL; > > > > + goto unlock_mutex; > > > > + } > > > > + > > > > + ret = svs_get_bank_zone_temperature(svsb->tzone_name, > > > > + &tzone_temp); > > > > + if (ret) { > > > > + dev_err(svsb->dev, "no \"%s\"?(%d)?\n", > > > > + svsb->tzone_name, ret); > > > > + dev_err(svsb->dev, "set signed-off voltage\n"); > > > > > > Please merge the error message in one line (I'm not sure what "set > > > signed-off voltage" means here). > > > > 1. Ok, I'll merge them. Thanks. > > 2. signed-off voltages means CPU DVFS default voltages > > So just write "default voltages" then? ,-) Ok, thanks. :) > > > > > > > [snip] > > > > +static irqreturn_t svs_isr(int irq, void *data) > > > > +{ > > > > + struct svs_platform *svsp = (struct svs_platform *)data; > > > > > > cast not needed. > > > > Ok, I'll remove it. Thanks. > > > > > > > > > + struct svs_bank *svsb = NULL; > > > > + unsigned long flags; > > > > + u32 idx, int_sts, svs_en; > > > > + > > > > + for (idx = 0; idx < svsp->bank_num; idx++) { > > > > + svsb = &svsp->banks[idx]; > > > > + > > > > + spin_lock_irqsave(&mtk_svs_lock, flags); > > > > + svsp->pbank = svsb; > > > > + > > > > + /* Find out which svs bank fires interrupt */ > > > > + if (svsb->int_st & svs_readl(svsp, INTST)) { > > > > + spin_unlock_irqrestore(&mtk_svs_lock, flags); > > > > + continue; > > > > + } > > > > + > > > > + if (!svsb->suspended) { > > > > + svs_switch_bank(svsp); > > > > + int_sts = svs_readl(svsp, INTSTS); > > > > + svs_en = svs_readl(svsp, SVSEN); > > > > + > > > > + if (int_sts == SVSB_INTSTS_COMPLETE && > > > > + ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT01)) > > > > + svs_init01_isr_handler(svsp); > > > > + else if ((int_sts == SVSB_INTSTS_COMPLETE) && > > > > + ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT02)) > > > > + svs_init02_isr_handler(svsp); > > > > + else if (!!(int_sts & SVSB_INTSTS_MONVOP)) > > > > > > !! is not required. > > > > Ok, I'll remove it. Thanks. > > > > > > > > > + svs_mon_mode_isr_handler(svsp); > > > > + else > > > > + svs_error_isr_handler(svsp); > > > > + } > > > > + > > > > + spin_unlock_irqrestore(&mtk_svs_lock, flags); > > > > + break; > > > > + } > > > > > > This will panic if svsb is NULL, is that ok or do you want to catch that? > > > > Oh, it is fine. Thanks for the heads-up. > > I should have been stronger in my statement, I think you want to add a > BUG_ON(!svsb) to crash in a slightly more predictable manner. Ok, I'll add BUG_ON(!svsb) to give an evident heads-up. Thanks. > > [snip] > > > > + > > > > + svsp->tefuse = (u32 *)nvmem_cell_read(cell, &svsp->tefuse_num); > > > > > > Cast not needed. > > > > Ok, I'll remove it if build/test ok. Because nvmem_cell_read returns > > (void *). > > > > > > > > Also, this need to be freed somewhere in remove code (kfree(svsp->tefuse)). > > > > > > And it seems like svsp->tefuse is only used in this function, can you > > > just allocate it here? > > > > Oh, svsp->tefuse will be used in SVS debug patch for debug purpose. So, > > I need to save it as struct member. > > Oh I missed that, sgtm then. Thanks. > > > > [snip]
Hi Nicolas, [snip] > > > > > + > > > + /* Svs efuse parsing */ > > > + ft_pgm = (svsp->efuse[0] >> 4) & GENMASK(3, 0); > > > + > > > + for (idx = 0; idx < svsp->bank_num; idx++) { > > > + svsb = &svsp->banks[idx]; > > > + > > > + if (ft_pgm <= 1) > > > + svsb->init01_volt_flag = SVSB_INIT01_VOLT_IGNORE; > > > + > > > + switch (svsb->sw_id) { > > > + case SVSB_CPU_LITTLE: > > > + svsb->bdes = svsp->efuse[16] & GENMASK(7, 0); > > > + svsb->mdes = (svsp->efuse[16] >> 8) & GENMASK(7, 0); > > > + svsb->dcbdet = (svsp->efuse[16] >> 16) & GENMASK(7, 0); > > > + svsb->dcmdet = (svsp->efuse[16] >> 24) & GENMASK(7, 0); > > > + svsb->mtdes = (svsp->efuse[17] >> 16) & GENMASK(7, 0); > > > > Again, if all of those values were u8, there'd be no need for these GENMASK > > Ok, I'll use u8 instead of GENMASK. Thanks. After refining the codes, I think it's much explicit to assign the bits I want by GENMASK() and will remove other GENMASK() that are repetitive like in svs_set_bank_phase() or svs_set_freqs_pct_v2(). [snip]
On Wed, Jan 6, 2021 at 4:41 PM Roger Lu <roger.lu@mediatek.com> wrote: > > Hi Nicolas, > > [snip] > > > > > > > + > > > > + /* Svs efuse parsing */ > > > > + ft_pgm = (svsp->efuse[0] >> 4) & GENMASK(3, 0); > > > > + > > > > + for (idx = 0; idx < svsp->bank_num; idx++) { > > > > + svsb = &svsp->banks[idx]; > > > > + > > > > + if (ft_pgm <= 1) > > > > + svsb->init01_volt_flag = SVSB_INIT01_VOLT_IGNORE; > > > > + > > > > + switch (svsb->sw_id) { > > > > + case SVSB_CPU_LITTLE: > > > > + svsb->bdes = svsp->efuse[16] & GENMASK(7, 0); > > > > + svsb->mdes = (svsp->efuse[16] >> 8) & GENMASK(7, 0); > > > > + svsb->dcbdet = (svsp->efuse[16] >> 16) & GENMASK(7, 0); > > > > + svsb->dcmdet = (svsp->efuse[16] >> 24) & GENMASK(7, 0); > > > > + svsb->mtdes = (svsp->efuse[17] >> 16) & GENMASK(7, 0); > > > > > > Again, if all of those values were u8, there'd be no need for these GENMASK > > > > Ok, I'll use u8 instead of GENMASK. Thanks. > > After refining the codes, I think it's much explicit to assign the bits > I want by GENMASK() and will remove other GENMASK() that are repetitive > like in svs_set_bank_phase() or svs_set_freqs_pct_v2(). I'm not sure what you mean, but, sure, you can go ahead with v11 and we'll see how it looks. Thanks, > [snip] >
diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig index 59a56cd790ec..f33da25f8336 100644 --- a/drivers/soc/mediatek/Kconfig +++ b/drivers/soc/mediatek/Kconfig @@ -51,4 +51,14 @@ config MTK_MMSYS Say yes here to add support for the MediaTek Multimedia Subsystem (MMSYS). +config MTK_SVS + tristate "MediaTek Smart Voltage Scaling(SVS)" + depends on MTK_EFUSE && NVMEM + help + The Smart Voltage Scaling(SVS) engine is a piece of hardware + which has several controllers(banks) for calculating suitable + voltage to different power domains(CPU/GPU/CCI) according to + chip process corner, temperatures and other factors. Then DVFS + driver could apply SVS bank voltage to PMIC/Buck. + endmenu diff --git a/drivers/soc/mediatek/Makefile b/drivers/soc/mediatek/Makefile index 01f9f873634a..e10f2cd87514 100644 --- a/drivers/soc/mediatek/Makefile +++ b/drivers/soc/mediatek/Makefile @@ -4,3 +4,4 @@ obj-$(CONFIG_MTK_INFRACFG) += mtk-infracfg.o obj-$(CONFIG_MTK_PMIC_WRAP) += mtk-pmic-wrap.o obj-$(CONFIG_MTK_SCPSYS) += mtk-scpsys.o obj-$(CONFIG_MTK_MMSYS) += mtk-mmsys.o +obj-$(CONFIG_MTK_SVS) += mtk-svs.o diff --git a/drivers/soc/mediatek/mtk-svs.c b/drivers/soc/mediatek/mtk-svs.c new file mode 100644 index 000000000000..0efefb48839d --- /dev/null +++ b/drivers/soc/mediatek/mtk-svs.c @@ -0,0 +1,1748 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2020 MediaTek Inc. + */ + +#include <linux/bits.h> +#include <linux/clk.h> +#include <linux/completion.h> +#include <linux/device.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/kthread.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/nvmem-consumer.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/of_platform.h> +#include <linux/platform_device.h> +#include <linux/pm_domain.h> +#include <linux/pm_opp.h> +#include <linux/pm_qos.h> +#include <linux/pm_runtime.h> +#include <linux/regulator/consumer.h> +#include <linux/reset.h> +#include <linux/slab.h> +#include <linux/spinlock.h> +#include <linux/thermal.h> + +/* svs bank 1-line sw id */ +#define SVSB_CPU_LITTLE BIT(0) +#define SVSB_CPU_BIG BIT(1) +#define SVSB_CCI BIT(2) +#define SVSB_GPU BIT(3) + +/* svs bank mode support */ +#define SVSB_MODE_ALL_DISABLE 0 +#define SVSB_MODE_INIT01 BIT(1) +#define SVSB_MODE_INIT02 BIT(2) +#define SVSB_MODE_MON BIT(3) + +/* svs bank init01 condition */ +#define SVSB_INIT01_VOLT_IGNORE BIT(1) +#define SVSB_INIT01_VOLT_INC_ONLY BIT(2) +#define SVSB_INIT01_CLK_EN BIT(31) + +/* svs bank common setting */ +#define SVSB_TZONE_HIGH_TEMP_MAX U32_MAX +#define SVSB_RUNCONFIG_DEFAULT 0x80000000 +#define SVSB_DC_SIGNED_BIT 0x8000 +#define SVSB_INTEN_INIT0x 0x00005f01 +#define SVSB_INTEN_MONVOPEN 0x00ff0000 +#define SVSB_EN_OFF 0x0 +#define SVSB_EN_MASK 0x7 +#define SVSB_EN_INIT01 0x1 +#define SVSB_EN_INIT02 0x5 +#define SVSB_EN_MON 0x2 +#define SVSB_INTSTS_MONVOP 0x00ff0000 +#define SVSB_INTSTS_COMPLETE 0x1 +#define SVSB_INTSTS_CLEAN 0x00ffffff + +static DEFINE_SPINLOCK(mtk_svs_lock); + +/* + * enum svsb_phase - svs bank phase enumeration + * @SVSB_PHASE_INIT01: basic init for svs bank + * @SVSB_PHASE_INIT02: svs bank can provide voltages + * @SVSB_PHASE_MON: svs bank can provide voltages with thermal effect + * @SVSB_PHASE_ERROR: svs bank encouters unexpected condition + * + * Each svs bank has its own independent phase. We enable each svs bank by + * running their phase orderly. However, When svs bank ecnounters unexpected + * condition, it will fire an irq (PHASE_ERROR) to inform svs software. + * + * svs bank general phase-enabled order: + * SVSB_PHASE_INIT01 -> SVSB_PHASE_INIT02 -> SVSB_PHASE_MON + */ +enum svsb_phase { + SVSB_PHASE_INIT01 = 0, + SVSB_PHASE_INIT02, + SVSB_PHASE_MON, + SVSB_PHASE_ERROR, +}; + +enum svs_reg_index { + DESCHAR = 0, + TEMPCHAR, + DETCHAR, + AGECHAR, + DCCONFIG, + AGECONFIG, + FREQPCT30, + FREQPCT74, + LIMITVALS, + VBOOT, + DETWINDOW, + CONFIG, + TSCALCS, + RUNCONFIG, + SVSEN, + INIT2VALS, + DCVALUES, + AGEVALUES, + VOP30, + VOP74, + TEMP, + INTSTS, + INTSTSRAW, + INTEN, + CHKINT, + CHKSHIFT, + STATUS, + VDESIGN30, + VDESIGN74, + DVT30, + DVT74, + AGECOUNT, + SMSTATE0, + SMSTATE1, + CTL0, + DESDETSEC, + TEMPAGESEC, + CTRLSPARE0, + CTRLSPARE1, + CTRLSPARE2, + CTRLSPARE3, + CORESEL, + THERMINTST, + INTST, + THSTAGE0ST, + THSTAGE1ST, + THSTAGE2ST, + THAHBST0, + THAHBST1, + SPARE0, + SPARE1, + SPARE2, + SPARE3, + THSLPEVEB, + reg_num, +}; + +static const u32 svs_regs_v2[] = { + [DESCHAR] = 0xc00, + [TEMPCHAR] = 0xc04, + [DETCHAR] = 0xc08, + [AGECHAR] = 0xc0c, + [DCCONFIG] = 0xc10, + [AGECONFIG] = 0xc14, + [FREQPCT30] = 0xc18, + [FREQPCT74] = 0xc1c, + [LIMITVALS] = 0xc20, + [VBOOT] = 0xc24, + [DETWINDOW] = 0xc28, + [CONFIG] = 0xc2c, + [TSCALCS] = 0xc30, + [RUNCONFIG] = 0xc34, + [SVSEN] = 0xc38, + [INIT2VALS] = 0xc3c, + [DCVALUES] = 0xc40, + [AGEVALUES] = 0xc44, + [VOP30] = 0xc48, + [VOP74] = 0xc4c, + [TEMP] = 0xc50, + [INTSTS] = 0xc54, + [INTSTSRAW] = 0xc58, + [INTEN] = 0xc5c, + [CHKINT] = 0xc60, + [CHKSHIFT] = 0xc64, + [STATUS] = 0xc68, + [VDESIGN30] = 0xc6c, + [VDESIGN74] = 0xc70, + [DVT30] = 0xc74, + [DVT74] = 0xc78, + [AGECOUNT] = 0xc7c, + [SMSTATE0] = 0xc80, + [SMSTATE1] = 0xc84, + [CTL0] = 0xc88, + [DESDETSEC] = 0xce0, + [TEMPAGESEC] = 0xce4, + [CTRLSPARE0] = 0xcf0, + [CTRLSPARE1] = 0xcf4, + [CTRLSPARE2] = 0xcf8, + [CTRLSPARE3] = 0xcfc, + [CORESEL] = 0xf00, + [THERMINTST] = 0xf04, + [INTST] = 0xf08, + [THSTAGE0ST] = 0xf0c, + [THSTAGE1ST] = 0xf10, + [THSTAGE2ST] = 0xf14, + [THAHBST0] = 0xf18, + [THAHBST1] = 0xf1c, + [SPARE0] = 0xf20, + [SPARE1] = 0xf24, + [SPARE2] = 0xf28, + [SPARE3] = 0xf2c, + [THSLPEVEB] = 0xf30, +}; + +/* + * struct thermal_parameter - This is for storing thermal efuse data. + * We cacluate thermal efuse data to produce "mts" and "bts" for + * svs bank mon mode. + */ +struct thermal_parameter { + int adc_ge_t; + int adc_oe_t; + int ge; + int oe; + int gain; + int o_vtsabb; + int o_vtsmcu1; + int o_vtsmcu2; + int o_vtsmcu3; + int o_vtsmcu4; + int o_vtsmcu5; + int degc_cali; + int adc_cali_en_t; + int o_slope; + int o_slope_sign; + int ts_id; +}; + +/* + * struct svs_bank - svs bank representation + * @dev: svs bank device + * @opp_dev: device for opp table/buck control + * @pd_dev: power domain device for SOC mtcmos control + * @init_completion: the timeout completion for bank init + * @buck: phandle of the regulator + * @lock: mutex lock to protect voltage update process + * @suspended: suspend flag of this bank + * @pd_req: bank's power-domain on request + * @volt_offset: bank voltage offset controlled by svs software + * @mode_support: bank mode support. + * @opp_freqs: signed-off frequencies from default opp table + * @opp_volts: signed-off voltages from default opp table + * @freqs_pct: percent of "opp_freqs / freq_base" for bank init + * @volts: bank voltages + * @freq_base: reference frequency for bank init + * @vboot: voltage request for bank init01 stage only + * @volt_step: bank voltage step + * @volt_base: bank voltage base + * @init01_volt_flag: bank init01 voltage flag + * @phase: bank current phase + * @vmax: bank voltage maximum + * @vmin: bank votlage minimum + * @temp: bank temperature + * @temp_upper_bound: bank temperature upper bound + * @temp_lower_bound: bank temperature lower bound + * @tzone_high_temp: thermal zone high temperature threshold + * @tzone_high_temp_offset: thermal zone high temperature offset + * @tzone_low_temp: thermal zone low temperature threshold + * @tzone_low_temp_offset: thermal zone low temperature offset + * @core_sel: bank selection + * @opp_count: bank opp count + * @int_st: bank interrupt identification + * @sw_id: bank software identification + * @ctl0: bank thermal sensor selection + * @cpu_id: cpu core id for SVS CPU only + * @name: bank name + * @tzone_name: thermal zone name + * @buck_name: regulator name + * + * Other structure members which are not listed above are svs platform + * efuse data for bank init + */ +struct svs_bank { + struct device *dev; + struct device *opp_dev; + struct device *pd_dev; + struct completion init_completion; + struct regulator *buck; + struct mutex lock; /* lock to protect voltage update process */ + bool suspended; + bool pd_req; + s32 volt_offset; + u32 mode_support; + u32 opp_freqs[16]; + u32 opp_volts[16]; + u32 freqs_pct[16]; + u32 volts[16]; + u32 freq_base; + u32 vboot; + u32 volt_step; + u32 volt_base; + u32 init01_volt_flag; + u32 phase; + u32 vmax; + u32 vmin; + u32 bts; + u32 mts; + u32 bdes; + u32 mdes; + u32 mtdes; + u32 dcbdet; + u32 dcmdet; + u32 dthi; + u32 dtlo; + u32 det_window; + u32 det_max; + u32 age_config; + u32 age_voffset_in; + u32 agem; + u32 dc_config; + u32 dc_voffset_in; + u32 dvt_fixed; + u32 vco; + u32 chk_shift; + u32 temp; + u32 temp_upper_bound; + u32 temp_lower_bound; + u32 tzone_high_temp; + u32 tzone_high_temp_offset; + u32 tzone_low_temp; + u32 tzone_low_temp_offset; + u32 core_sel; + u32 opp_count; + u32 int_st; + u32 sw_id; + u32 ctl0; + u32 cpu_id; + u8 *name; + u8 *tzone_name; + u8 *buck_name; +}; + +/* + * struct svs_platform - svs platform data + * @dev: svs platform device + * @base: svs platform register address base + * @main_clk: main clock for svs bank + * @pbank: phandle of svs bank and needs to be protected by spin_lock + * @banks: phandle of the banks that support + * @efuse_parsing: phandle of efuse parsing function + * @set_freqs_pct: phandle of set frequencies percent function + * @get_vops: phandle of get bank voltages function + * @irqflags: irq settings flags + * @fake_efuse: the flag for running svs with fake efuse + * @rst: svs reset control + * @regs: phandle to the registers map + * @efuse_num: the total number of svs platform efuse + * @tefuse_num: the total number of thermal efuse + * @bank_num: the total number of banks + * @efuse_check: the svs efuse check index + * @efuse: svs platform efuse data received from NVMEM framework + * @tefuse: thermal efuse data received from NVMEM framework + * @name: svs platform name + */ +struct svs_platform { + struct device *dev; + void __iomem *base; + struct clk *main_clk; + struct svs_bank *pbank; + struct svs_bank *banks; + bool (*efuse_parsing)(struct svs_platform *svsp); + void (*set_freqs_pct)(struct svs_platform *svsp); + void (*get_vops)(struct svs_platform *svsp); + unsigned long irqflags; + bool fake_efuse; + struct reset_control *rst; + const u32 *regs; + size_t efuse_num; + size_t tefuse_num; + u32 bank_num; + u32 efuse_check; + u32 *efuse; + u32 *tefuse; + u8 *name; +}; + +static u32 percent(u32 numerator, u32 denominator) +{ + u32 pct; + + /* If not divide 1000, "numerator * 100" will have data overflow. */ + numerator /= 1000; + denominator /= 1000; + pct = ((numerator * 100) + denominator - 1) / denominator; + pct &= GENMASK(7, 0); + + return pct; +} + +static u32 svs_readl(struct svs_platform *svsp, enum svs_reg_index rg_i) +{ + return readl(svsp->base + svsp->regs[rg_i]); +} + +static void svs_writel(struct svs_platform *svsp, u32 val, + enum svs_reg_index rg_i) +{ + writel(val, svsp->base + svsp->regs[rg_i]); +} + +static void svs_switch_bank(struct svs_platform *svsp) +{ + struct svs_bank *svsb = svsp->pbank; + + svs_writel(svsp, svsb->core_sel, CORESEL); +} + +static u32 svs_bank_volt_to_opp_volt(u32 svsb_volt, u32 svsb_volt_step, + u32 svsb_volt_base) +{ + u32 opp_u_volt; + + opp_u_volt = (svsb_volt * svsb_volt_step) + svsb_volt_base; + + return opp_u_volt; +} + +static int svs_get_bank_zone_temperature(u8 *tzone_name, int *tzone_temp) +{ + struct thermal_zone_device *tzd; + + tzd = thermal_zone_get_zone_by_name(tzone_name); + if (IS_ERR(tzd)) + return PTR_ERR(tzd); + + return thermal_zone_get_temp(tzd, tzone_temp); +} + +static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update) +{ + int tzone_temp, ret = -EPERM; + u32 i, svsb_volt, opp_volt, temp_offset = 0; + + mutex_lock(&svsb->lock); + + /* + * If svs bank is suspended, it means signed-off voltages are applied. + * Don't need to update opp voltage anymore. + */ + if (svsb->suspended && !force_update) { + dev_notice(svsb->dev, "bank is suspended\n"); + ret = -EPERM; + goto unlock_mutex; + } + + /* Get thermal effect */ + if (svsb->phase == SVSB_PHASE_MON) { + if (svsb->temp > svsb->temp_upper_bound && + svsb->temp < svsb->temp_lower_bound) { + dev_warn(svsb->dev, "svsb temp = 0x%x?\n", svsb->temp); + ret = -EINVAL; + goto unlock_mutex; + } + + ret = svs_get_bank_zone_temperature(svsb->tzone_name, + &tzone_temp); + if (ret) { + dev_err(svsb->dev, "no \"%s\"?(%d)?\n", + svsb->tzone_name, ret); + dev_err(svsb->dev, "set signed-off voltage\n"); + svsb->phase = SVSB_PHASE_ERROR; + } + + if (tzone_temp >= svsb->tzone_high_temp) + temp_offset += svsb->tzone_high_temp_offset; + else if (tzone_temp <= svsb->tzone_low_temp) + temp_offset += svsb->tzone_low_temp_offset; + } + + /* vmin <= svsb_volt (opp_volt) <= signed-off voltage */ + for (i = 0; i < svsb->opp_count; i++) { + if (svsb->phase == SVSB_PHASE_MON) { + svsb_volt = max((svsb->volts[i] + svsb->volt_offset + + temp_offset), svsb->vmin); + opp_volt = svs_bank_volt_to_opp_volt(svsb_volt, + svsb->volt_step, + svsb->volt_base); + } else if (svsb->phase == SVSB_PHASE_INIT02) { + svsb_volt = max((svsb->volts[i] + svsb->volt_offset), + svsb->vmin); + opp_volt = svs_bank_volt_to_opp_volt(svsb_volt, + svsb->volt_step, + svsb->volt_base); + } else if (svsb->phase == SVSB_PHASE_ERROR) { + opp_volt = svsb->opp_volts[i]; + } else { + dev_err(svsb->dev, "unknown phase: %u?\n", svsb->phase); + ret = -EINVAL; + goto unlock_mutex; + } + + opp_volt = min(opp_volt, svsb->opp_volts[i]); + ret = dev_pm_opp_adjust_voltage(svsb->opp_dev, + svsb->opp_freqs[i], + opp_volt, opp_volt, + svsb->opp_volts[i]); + if (ret) { + dev_err(svsb->dev, "set voltage fail: %d\n", ret); + goto unlock_mutex; + } + } + +unlock_mutex: + mutex_unlock(&svsb->lock); + + return ret; +} + +static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx) +{ + u32 vy; + + if (v0 == v1 || f0 == f1) + return v0; + + /* *100 to have decimal fraction factor, +99 for rounding up. */ + vy = (v0 * 100) - ((((v0 - v1) * 100) / (f0 - f1)) * (f0 - fx)); + vy = (vy + 99) / 100; + + return vy; +} + +static void svs_get_vops_v2(struct svs_platform *svsp) +{ + struct svs_bank *svsb = svsp->pbank; + u32 temp, i; + + temp = svs_readl(svsp, VOP74); + svsb->volts[14] = (temp >> 24) & GENMASK(7, 0); + svsb->volts[12] = (temp >> 16) & GENMASK(7, 0); + svsb->volts[10] = (temp >> 8) & GENMASK(7, 0); + svsb->volts[8] = (temp & GENMASK(7, 0)); + + temp = svs_readl(svsp, VOP30); + svsb->volts[6] = (temp >> 24) & GENMASK(7, 0); + svsb->volts[4] = (temp >> 16) & GENMASK(7, 0); + svsb->volts[2] = (temp >> 8) & GENMASK(7, 0); + svsb->volts[0] = (temp & GENMASK(7, 0)); + + for (i = 0; i <= 7; i++) { + if (i < 7) { + svsb->volts[(i * 2) + 1] = + interpolate(svsb->freqs_pct[i * 2], + svsb->freqs_pct[(i + 1) * 2], + svsb->volts[i * 2], + svsb->volts[(i + 1) * 2], + svsb->freqs_pct[(i * 2) + 1]); + } else if (i == 7) { + svsb->volts[(i * 2) + 1] = + interpolate(svsb->freqs_pct[(i - 1) * 2], + svsb->freqs_pct[i * 2], + svsb->volts[(i - 1) * 2], + svsb->volts[i * 2], + svsb->freqs_pct[(i * 2) + 1]); + } + } +} + +static void svs_set_freqs_pct_v2(struct svs_platform *svsp) +{ + struct svs_bank *svsb = svsp->pbank; + + svs_writel(svsp, + ((svsb->freqs_pct[14] << 24) & GENMASK(31, 24)) | + ((svsb->freqs_pct[12] << 16) & GENMASK(23, 16)) | + ((svsb->freqs_pct[10] << 8) & GENMASK(15, 8)) | + ((svsb->freqs_pct[8]) & GENMASK(7, 0)), + FREQPCT74); + + svs_writel(svsp, + ((svsb->freqs_pct[6] << 24) & GENMASK(31, 24)) | + ((svsb->freqs_pct[4] << 16) & GENMASK(23, 16)) | + ((svsb->freqs_pct[2] << 8) & GENMASK(15, 8)) | + (svsb->freqs_pct[0] & GENMASK(7, 0)), + FREQPCT30); +} + +static void svs_set_bank_phase(struct svs_platform *svsp, u32 target_phase) +{ + struct svs_bank *svsb = svsp->pbank; + u32 des_char, temp_char, det_char, limit_vals; + u32 init2vals, ts_calcs, val, filter, i; + + svs_switch_bank(svsp); + + des_char = ((svsb->bdes << 8) & GENMASK(15, 8)) | + (svsb->mdes & GENMASK(7, 0)); + svs_writel(svsp, des_char, DESCHAR); + + temp_char = ((svsb->vco << 16) & GENMASK(23, 16)) | + ((svsb->mtdes << 8) & GENMASK(15, 8)) | + (svsb->dvt_fixed & GENMASK(7, 0)); + svs_writel(svsp, temp_char, TEMPCHAR); + + det_char = ((svsb->dcbdet << 8) & GENMASK(15, 8)) | + (svsb->dcmdet & GENMASK(7, 0)); + svs_writel(svsp, det_char, DETCHAR); + + svs_writel(svsp, svsb->dc_config, DCCONFIG); + svs_writel(svsp, svsb->age_config, AGECONFIG); + + if (!svsb->agem) { + svs_writel(svsp, SVSB_RUNCONFIG_DEFAULT, RUNCONFIG); + } else { + val = 0x0; + + for (i = 0; i < 24; i += 2) { + filter = 0x3 << i; + + if (!(svsb->age_config & filter)) + val |= (0x1 << i); + else + val |= (svsb->age_config & filter); + } + svs_writel(svsp, val, RUNCONFIG); + } + + svsp->set_freqs_pct(svsp); + + limit_vals = ((svsb->vmax << 24) & GENMASK(31, 24)) | + ((svsb->vmin << 16) & GENMASK(23, 16)) | + ((svsb->dthi << 8) & GENMASK(15, 8)) | + (svsb->dtlo & GENMASK(7, 0)); + svs_writel(svsp, limit_vals, LIMITVALS); + svs_writel(svsp, (svsb->vboot & GENMASK(7, 0)), VBOOT); + svs_writel(svsp, (svsb->det_window & GENMASK(15, 0)), DETWINDOW); + svs_writel(svsp, (svsb->det_max & GENMASK(15, 0)), CONFIG); + + if (svsb->chk_shift) + svs_writel(svsp, (svsb->chk_shift & GENMASK(7, 0)), CHKSHIFT); + + if (svsb->ctl0) + svs_writel(svsp, svsb->ctl0, CTL0); + + svs_writel(svsp, SVSB_INTSTS_CLEAN, INTSTS); + + switch (target_phase) { + case SVSB_PHASE_INIT01: + svs_writel(svsp, SVSB_INTEN_INIT0x, INTEN); + svs_writel(svsp, SVSB_EN_INIT01, SVSEN); + break; + case SVSB_PHASE_INIT02: + svs_writel(svsp, SVSB_INTEN_INIT0x, INTEN); + init2vals = ((svsb->age_voffset_in << 16) & GENMASK(31, 16)) | + (svsb->dc_voffset_in & GENMASK(15, 0)); + svs_writel(svsp, init2vals, INIT2VALS); + svs_writel(svsp, SVSB_EN_INIT02, SVSEN); + break; + case SVSB_PHASE_MON: + ts_calcs = ((svsb->bts << 12) & GENMASK(23, 12)) | + (svsb->mts & GENMASK(11, 0)); + svs_writel(svsp, ts_calcs, TSCALCS); + svs_writel(svsp, SVSB_INTEN_MONVOPEN, INTEN); + svs_writel(svsp, SVSB_EN_MON, SVSEN); + break; + default: + WARN_ON(1); + break; + } +} + +static inline void svs_init01_isr_handler(struct svs_platform *svsp) +{ + struct svs_bank *svsb = svsp->pbank; + + dev_info(svsb->dev, "%s: VDN74~30:0x%08x~0x%08x, DC:0x%08x\n", + __func__, svs_readl(svsp, VDESIGN74), + svs_readl(svsp, VDESIGN30), svs_readl(svsp, DCVALUES)); + + svsb->phase = SVSB_PHASE_INIT01; + svsb->dc_voffset_in = ~(svs_readl(svsp, DCVALUES) & GENMASK(15, 0)) + 1; + if (svsb->init01_volt_flag == SVSB_INIT01_VOLT_IGNORE) + svsb->dc_voffset_in = 0; + else if ((svsb->dc_voffset_in & SVSB_DC_SIGNED_BIT) && + (svsb->init01_volt_flag == SVSB_INIT01_VOLT_INC_ONLY)) + svsb->dc_voffset_in = 0; + + svsb->age_voffset_in = svs_readl(svsp, AGEVALUES) & GENMASK(15, 0); + + svs_writel(svsp, SVSB_EN_OFF, SVSEN); + svs_writel(svsp, SVSB_INTSTS_COMPLETE, INTSTS); + + /* svs init01 clock gating */ + svsb->core_sel &= ~SVSB_INIT01_CLK_EN; +} + +static inline void svs_init02_isr_handler(struct svs_platform *svsp) +{ + struct svs_bank *svsb = svsp->pbank; + + dev_info(svsb->dev, "%s: VOP74~30:0x%08x~0x%08x, DC:0x%08x\n", + __func__, svs_readl(svsp, VOP74), svs_readl(svsp, VOP30), + svs_readl(svsp, DCVALUES)); + + svsb->phase = SVSB_PHASE_INIT02; + svsp->get_vops(svsp); + + svs_writel(svsp, SVSB_EN_OFF, SVSEN); + svs_writel(svsp, SVSB_INTSTS_COMPLETE, INTSTS); +} + +static inline void svs_mon_mode_isr_handler(struct svs_platform *svsp) +{ + struct svs_bank *svsb = svsp->pbank; + + svsb->phase = SVSB_PHASE_MON; + svsb->temp = svs_readl(svsp, TEMP) & GENMASK(7, 0); + svsp->get_vops(svsp); + + svs_writel(svsp, SVSB_INTSTS_MONVOP, INTSTS); +} + +static inline void svs_error_isr_handler(struct svs_platform *svsp) +{ + struct svs_bank *svsb = svsp->pbank; + + dev_err(svsb->dev, "%s: CORESEL = 0x%08x\n", + __func__, svs_readl(svsp, CORESEL)); + dev_err(svsb->dev, "SVSEN = 0x%08x, INTSTS = 0x%08x\n", + svs_readl(svsp, SVSEN), svs_readl(svsp, INTSTS)); + dev_err(svsb->dev, "SMSTATE0 = 0x%08x, SMSTATE1 = 0x%08x\n", + svs_readl(svsp, SMSTATE0), svs_readl(svsp, SMSTATE1)); + dev_err(svsb->dev, "TEMP = 0x%08x\n", svs_readl(svsp, TEMP)); + + svsb->mode_support = SVSB_MODE_ALL_DISABLE; + svsb->phase = SVSB_PHASE_ERROR; + + svs_writel(svsp, SVSB_EN_OFF, SVSEN); + svs_writel(svsp, SVSB_INTSTS_CLEAN, INTSTS); +} + +static irqreturn_t svs_isr(int irq, void *data) +{ + struct svs_platform *svsp = (struct svs_platform *)data; + struct svs_bank *svsb = NULL; + unsigned long flags; + u32 idx, int_sts, svs_en; + + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + + spin_lock_irqsave(&mtk_svs_lock, flags); + svsp->pbank = svsb; + + /* Find out which svs bank fires interrupt */ + if (svsb->int_st & svs_readl(svsp, INTST)) { + spin_unlock_irqrestore(&mtk_svs_lock, flags); + continue; + } + + if (!svsb->suspended) { + svs_switch_bank(svsp); + int_sts = svs_readl(svsp, INTSTS); + svs_en = svs_readl(svsp, SVSEN); + + if (int_sts == SVSB_INTSTS_COMPLETE && + ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT01)) + svs_init01_isr_handler(svsp); + else if ((int_sts == SVSB_INTSTS_COMPLETE) && + ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT02)) + svs_init02_isr_handler(svsp); + else if (!!(int_sts & SVSB_INTSTS_MONVOP)) + svs_mon_mode_isr_handler(svsp); + else + svs_error_isr_handler(svsp); + } + + spin_unlock_irqrestore(&mtk_svs_lock, flags); + break; + } + + if (svsb->phase != SVSB_PHASE_INIT01) + svs_adjust_pm_opp_volts(svsb, false); + + if (svsb->phase == SVSB_PHASE_INIT01 || + svsb->phase == SVSB_PHASE_INIT02) + complete(&svsb->init_completion); + + return IRQ_HANDLED; +} + +static void svs_mon_mode(struct svs_platform *svsp) +{ + struct svs_bank *svsb; + unsigned long flags; + u32 idx; + + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + + if (!(svsb->mode_support & SVSB_MODE_MON)) + continue; + + spin_lock_irqsave(&mtk_svs_lock, flags); + svsp->pbank = svsb; + svs_set_bank_phase(svsp, SVSB_PHASE_MON); + spin_unlock_irqrestore(&mtk_svs_lock, flags); + } +} + +static int svs_init02(struct svs_platform *svsp) +{ + struct svs_bank *svsb; + unsigned long flags, time_left; + u32 idx; + + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + + if (!(svsb->mode_support & SVSB_MODE_INIT02)) + continue; + + reinit_completion(&svsb->init_completion); + spin_lock_irqsave(&mtk_svs_lock, flags); + svsp->pbank = svsb; + svs_set_bank_phase(svsp, SVSB_PHASE_INIT02); + spin_unlock_irqrestore(&mtk_svs_lock, flags); + + time_left = + wait_for_completion_timeout(&svsb->init_completion, + msecs_to_jiffies(2000)); + if (!time_left) { + dev_err(svsb->dev, "init02 completion timeout\n"); + return -EBUSY; + } + } + + return 0; +} + +static int svs_init01(struct svs_platform *svsp) +{ + struct svs_bank *svsb; + struct pm_qos_request *qos_request; + unsigned long flags, time_left; + bool search_done, does_svsb_set_pd_on; + int ret = 0; + u32 opp_freqs, opp_vboot, buck_volt, idx, i; + + qos_request = kzalloc(sizeof(*qos_request), GFP_KERNEL); + if (!qos_request) + return -ENOMEM; + + /* Let CPUs leave idle-off state for initializing svs_init01. */ + cpu_latency_qos_add_request(qos_request, 0); + + /* + * Sometimes two svs banks use the same buck. + * Therefore, we set each svs bank to vboot voltage first. + */ + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + + if (!(svsb->mode_support & SVSB_MODE_INIT01)) + continue; + + search_done = false; + does_svsb_set_pd_on = false; + + if (regulator_set_mode(svsb->buck, REGULATOR_MODE_FAST)) + dev_notice(svsb->dev, "set fast mode fail\n"); + + if (svsb->pd_req) { + ret = regulator_enable(svsb->buck); + if (ret) { + dev_err(svsb->dev, "\"%s\" enable fail: %d\n", + svsb->buck_name, ret); + goto init01_finish; + } + + if (!pm_runtime_enabled(svsb->pd_dev)) { + pm_runtime_enable(svsb->pd_dev); + does_svsb_set_pd_on = true; + } + + ret = pm_runtime_get_sync(svsb->pd_dev); + if (ret < 0) { + dev_err(svsb->dev, "mtcmos on fail: %d\n", + ret); + goto init01_finish; + } + } + + /* + * Find the fastest freq that can be run at vboot and + * fix to that freq until svs_init01 is done. + */ + opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot, + svsb->volt_step, + svsb->volt_base); + + for (i = 0; i < svsb->opp_count; i++) { + opp_freqs = svsb->opp_freqs[i]; + if (!search_done && svsb->opp_volts[i] <= opp_vboot) { + ret = dev_pm_opp_adjust_voltage(svsb->opp_dev, + opp_freqs, + opp_vboot, + opp_vboot, + opp_vboot); + if (ret) { + dev_err(svsb->dev, + "set voltage fail: %d\n", ret); + goto init01_finish; + } + + search_done = true; + } else { + dev_pm_opp_disable(svsb->opp_dev, + svsb->opp_freqs[i]); + } + } + } + + /* svs bank init01 begins */ + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + + if (!(svsb->mode_support & SVSB_MODE_INIT01)) + continue; + + opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot, + svsb->volt_step, + svsb->volt_base); + + buck_volt = regulator_get_voltage(svsb->buck); + if (buck_volt != opp_vboot) { + dev_err(svsb->dev, + "buck voltage: %u, expected vboot: %u\n", + buck_volt, opp_vboot); + ret = -EPERM; + goto init01_finish; + } + + spin_lock_irqsave(&mtk_svs_lock, flags); + svsp->pbank = svsb; + svs_set_bank_phase(svsp, SVSB_PHASE_INIT01); + spin_unlock_irqrestore(&mtk_svs_lock, flags); + + time_left = + wait_for_completion_timeout(&svsb->init_completion, + msecs_to_jiffies(2000)); + if (!time_left) { + dev_err(svsb->dev, "init01 completion timeout\n"); + ret = -EBUSY; + goto init01_finish; + } + } + +init01_finish: + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + + if (!(svsb->mode_support & SVSB_MODE_INIT01)) + continue; + + for (i = 0; i < svsb->opp_count; i++) + dev_pm_opp_enable(svsb->opp_dev, svsb->opp_freqs[i]); + + if (regulator_set_mode(svsb->buck, REGULATOR_MODE_NORMAL)) + dev_notice(svsb->dev, "fail to set normal mode\n"); + + if (svsb->pd_req) { + if (pm_runtime_put_sync(svsb->pd_dev)) + dev_err(svsb->dev, "mtcmos off fail\n"); + + if (does_svsb_set_pd_on) { + pm_runtime_disable(svsb->pd_dev); + does_svsb_set_pd_on = false; + } + + if (regulator_disable(svsb->buck)) + dev_err(svsb->dev, "disable power fail\n"); + } + } + + cpu_latency_qos_remove_request(qos_request); + kfree(qos_request); + + return ret; +} + +static int svs_start(struct svs_platform *svsp) +{ + int ret; + + ret = svs_init01(svsp); + if (ret) + return ret; + + ret = svs_init02(svsp); + if (ret) + return ret; + + svs_mon_mode(svsp); + + return ret; +} + +static struct device *svs_get_subsys_device(struct svs_platform *svsp, + u8 *node_name) +{ + struct platform_device *pdev; + struct device_node *np; + + np = of_find_node_by_name(NULL, node_name); + if (!np) { + dev_err(svsp->dev, "cannot find %s node\n", node_name); + return ERR_PTR(-ENODEV); + } + + pdev = of_find_device_by_node(np); + if (!pdev) { + of_node_put(np); + dev_err(svsp->dev, "cannot find pdev by %s\n", node_name); + return ERR_PTR(-ENXIO); + } + + of_node_put(np); + + return &pdev->dev; +} + +static struct device *svs_add_device_link(struct svs_platform *svsp, + u8 *node_name) +{ + struct device *dev; + struct device_link *sup_link; + + if (!node_name) { + dev_err(svsp->dev, "node name cannot be null\n"); + return ERR_PTR(-EINVAL); + } + + dev = svs_get_subsys_device(svsp, node_name); + if (IS_ERR(dev)) + return dev; + + sup_link = device_link_add(svsp->dev, dev, + DL_FLAG_AUTOREMOVE_CONSUMER); + + if (sup_link->status == DL_STATE_DORMANT) + return ERR_PTR(-EPROBE_DEFER); + + return dev; +} + +static int svs_resource_setup(struct svs_platform *svsp) +{ + struct svs_bank *svsb; + struct dev_pm_opp *opp; + unsigned long freq; + int count, ret; + u32 idx, i; + + dev_set_drvdata(svsp->dev, svsp); + + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + + switch (svsb->sw_id) { + case SVSB_CPU_LITTLE: + svsb->name = "SVSB_CPU_LITTLE"; + break; + case SVSB_CPU_BIG: + svsb->name = "SVSB_CPU_BIG"; + break; + case SVSB_CCI: + svsb->name = "SVSB_CCI"; + break; + case SVSB_GPU: + svsb->name = "SVSB_GPU"; + break; + default: + WARN_ON(1); + return -EINVAL; + } + + svsb->dev = devm_kzalloc(svsp->dev, sizeof(*svsb->dev), + GFP_KERNEL); + if (!svsb->dev) + return -ENOMEM; + + ret = dev_set_name(svsb->dev, svsb->name); + if (ret) + return ret; + + dev_set_drvdata(svsb->dev, svsp); + + ret = dev_pm_opp_of_add_table(svsb->opp_dev); + if (ret) { + dev_err(svsb->dev, "add opp table fail: %d\n", ret); + return ret; + } + + mutex_init(&svsb->lock); + init_completion(&svsb->init_completion); + + svsb->buck = devm_regulator_get_optional(svsb->opp_dev, + svsb->buck_name); + if (IS_ERR(svsb->buck)) { + dev_err(svsb->dev, "cannot get \"%s-supply\"\n", + svsb->buck_name); + return PTR_ERR(svsb->buck); + } + + count = dev_pm_opp_get_opp_count(svsb->opp_dev); + if (svsb->opp_count != count) { + dev_err(svsb->dev, + "opp_count not \"%u\" but get \"%d\"?\n", + svsb->opp_count, count); + return count; + } + + for (i = 0, freq = U32_MAX; i < svsb->opp_count; i++, freq--) { + opp = dev_pm_opp_find_freq_floor(svsb->opp_dev, &freq); + if (IS_ERR(opp)) { + dev_err(svsb->dev, "cannot find freq = %ld\n", + PTR_ERR(opp)); + return PTR_ERR(opp); + } + + svsb->opp_freqs[i] = freq; + svsb->opp_volts[i] = dev_pm_opp_get_voltage(opp); + svsb->freqs_pct[i] = percent(svsb->opp_freqs[i], + svsb->freq_base); + dev_pm_opp_put(opp); + } + } + + return 0; +} + +static bool svs_mt8183_efuse_parsing(struct svs_platform *svsp) +{ + struct thermal_parameter tp; + struct svs_bank *svsb; + bool mon_mode_support = true; + int format[6], x_roomt[6], tb_roomt = 0; + struct nvmem_cell *cell; + u32 idx, i, ft_pgm, mts, temp0, temp1, temp2; + + if (svsp->fake_efuse) { + pr_notice("fake efuse\n"); + svsp->efuse[0] = 0x00310080; + svsp->efuse[1] = 0xabfbf757; + svsp->efuse[2] = 0x47c747c7; + svsp->efuse[3] = 0xabfbf757; + svsp->efuse[4] = 0xe7fca0ec; + svsp->efuse[5] = 0x47bf4b88; + svsp->efuse[6] = 0xabfb8fa5; + svsp->efuse[7] = 0xabfb217b; + svsp->efuse[8] = 0x4bf34be1; + svsp->efuse[9] = 0xabfb670d; + svsp->efuse[16] = 0xabfbc653; + svsp->efuse[17] = 0x47f347e1; + svsp->efuse[18] = 0xabfbd848; + } + + for (i = 0; i < svsp->efuse_num; i++) + if (svsp->efuse[i]) + dev_notice(svsp->dev, "M_HW_RES%d: 0x%08x\n", + i, svsp->efuse[i]); + + /* Svs efuse parsing */ + ft_pgm = (svsp->efuse[0] >> 4) & GENMASK(3, 0); + + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + + if (ft_pgm <= 1) + svsb->init01_volt_flag = SVSB_INIT01_VOLT_IGNORE; + + switch (svsb->sw_id) { + case SVSB_CPU_LITTLE: + svsb->bdes = svsp->efuse[16] & GENMASK(7, 0); + svsb->mdes = (svsp->efuse[16] >> 8) & GENMASK(7, 0); + svsb->dcbdet = (svsp->efuse[16] >> 16) & GENMASK(7, 0); + svsb->dcmdet = (svsp->efuse[16] >> 24) & GENMASK(7, 0); + svsb->mtdes = (svsp->efuse[17] >> 16) & GENMASK(7, 0); + + if (ft_pgm <= 3) + svsb->volt_offset += 10; + else + svsb->volt_offset += 2; + break; + case SVSB_CPU_BIG: + svsb->bdes = svsp->efuse[18] & GENMASK(7, 0); + svsb->mdes = (svsp->efuse[18] >> 8) & GENMASK(7, 0); + svsb->dcbdet = (svsp->efuse[18] >> 16) & GENMASK(7, 0); + svsb->dcmdet = (svsp->efuse[18] >> 24) & GENMASK(7, 0); + svsb->mtdes = svsp->efuse[17] & GENMASK(7, 0); + + if (ft_pgm <= 3) + svsb->volt_offset += 15; + else + svsb->volt_offset += 12; + break; + case SVSB_CCI: + svsb->bdes = svsp->efuse[4] & GENMASK(7, 0); + svsb->mdes = (svsp->efuse[4] >> 8) & GENMASK(7, 0); + svsb->dcbdet = (svsp->efuse[4] >> 16) & GENMASK(7, 0); + svsb->dcmdet = (svsp->efuse[4] >> 24) & GENMASK(7, 0); + svsb->mtdes = (svsp->efuse[5] >> 16) & GENMASK(7, 0); + + if (ft_pgm <= 3) + svsb->volt_offset += 10; + else + svsb->volt_offset += 2; + break; + case SVSB_GPU: + svsb->bdes = svsp->efuse[6] & GENMASK(7, 0); + svsb->mdes = (svsp->efuse[6] >> 8) & GENMASK(7, 0); + svsb->dcbdet = (svsp->efuse[6] >> 16) & GENMASK(7, 0); + svsb->dcmdet = (svsp->efuse[6] >> 24) & GENMASK(7, 0); + svsb->mtdes = svsp->efuse[5] & GENMASK(7, 0); + + if (ft_pgm >= 2) { + svsb->freq_base = 800000000; /* 800MHz */ + svsb->dvt_fixed = 2; + } + break; + default: + break; + } + } + + /* Get thermal efuse by nvmem */ + cell = nvmem_cell_get(svsp->dev, "t-calibration-data"); + if (IS_ERR_OR_NULL(cell)) { + dev_err(svsp->dev, "no thermal cell, no mon mode\n"); + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + svsb->mode_support &= ~SVSB_MODE_MON; + } + + return true; + } + + svsp->tefuse = (u32 *)nvmem_cell_read(cell, &svsp->tefuse_num); + svsp->tefuse_num /= sizeof(u32); + nvmem_cell_put(cell); + + if (svsp->fake_efuse) { + svsp->tefuse[0] = 0x02873f69; + svsp->tefuse[1] = 0xa11d9142; + svsp->tefuse[2] = 0xa2526900; + } + + /* Thermal efuse parsing */ + tp.adc_ge_t = (svsp->tefuse[1] >> 22) & GENMASK(9, 0); + tp.adc_oe_t = (svsp->tefuse[1] >> 12) & GENMASK(9, 0); + + tp.o_vtsmcu1 = (svsp->tefuse[0] >> 17) & GENMASK(8, 0); + tp.o_vtsmcu2 = (svsp->tefuse[0] >> 8) & GENMASK(8, 0); + tp.o_vtsmcu3 = svsp->tefuse[1] & GENMASK(8, 0); + tp.o_vtsmcu4 = (svsp->tefuse[2] >> 23) & GENMASK(8, 0); + tp.o_vtsmcu5 = (svsp->tefuse[2] >> 5) & GENMASK(8, 0); + tp.o_vtsabb = (svsp->tefuse[2] >> 14) & GENMASK(8, 0); + + tp.degc_cali = (svsp->tefuse[0] >> 1) & GENMASK(5, 0); + tp.adc_cali_en_t = svsp->tefuse[0] & BIT(0); + tp.o_slope_sign = (svsp->tefuse[0] >> 7) & BIT(0); + + tp.ts_id = (svsp->tefuse[1] >> 9) & BIT(0); + tp.o_slope = (svsp->tefuse[0] >> 26) & GENMASK(5, 0); + + if (tp.adc_cali_en_t == 1) { + if (!tp.ts_id) + tp.o_slope = 0; + + if ((tp.adc_ge_t < 265 || tp.adc_ge_t > 758) || + (tp.adc_oe_t < 265 || tp.adc_oe_t > 758) || + (tp.o_vtsmcu1 < -8 || tp.o_vtsmcu1 > 484) || + (tp.o_vtsmcu2 < -8 || tp.o_vtsmcu2 > 484) || + (tp.o_vtsmcu3 < -8 || tp.o_vtsmcu3 > 484) || + (tp.o_vtsmcu4 < -8 || tp.o_vtsmcu4 > 484) || + (tp.o_vtsmcu5 < -8 || tp.o_vtsmcu5 > 484) || + (tp.o_vtsabb < -8 || tp.o_vtsabb > 484) || + (tp.degc_cali < 1 || tp.degc_cali > 63)) { + dev_err(svsp->dev, "bad thermal efuse, no mon mode\n"); + mon_mode_support = false; + } + } else { + dev_err(svsp->dev, "no thermal efuse, no mon mode\n"); + mon_mode_support = false; + } + + if (!mon_mode_support) { + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + svsb->mode_support &= ~SVSB_MODE_MON; + } + + return true; + } + + tp.ge = ((tp.adc_ge_t - 512) * 10000) / 4096; + tp.oe = (tp.adc_oe_t - 512); + tp.gain = (10000 + tp.ge); + + format[0] = (tp.o_vtsmcu1 + 3350 - tp.oe); + format[1] = (tp.o_vtsmcu2 + 3350 - tp.oe); + format[2] = (tp.o_vtsmcu3 + 3350 - tp.oe); + format[3] = (tp.o_vtsmcu4 + 3350 - tp.oe); + format[4] = (tp.o_vtsmcu5 + 3350 - tp.oe); + format[5] = (tp.o_vtsabb + 3350 - tp.oe); + + for (i = 0; i < 6; i++) + x_roomt[i] = (((format[i] * 10000) / 4096) * 10000) / tp.gain; + + temp0 = (10000 * 100000 / tp.gain) * 15 / 18; + + if (!tp.o_slope_sign) + mts = (temp0 * 10) / (1534 + tp.o_slope * 10); + else + mts = (temp0 * 10) / (1534 - tp.o_slope * 10); + + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + svsb->mts = mts; + + switch (svsb->sw_id) { + case SVSB_CPU_LITTLE: + tb_roomt = x_roomt[3]; + break; + case SVSB_CPU_BIG: + tb_roomt = x_roomt[4]; + break; + case SVSB_CCI: + tb_roomt = x_roomt[3]; + break; + case SVSB_GPU: + tb_roomt = x_roomt[1]; + break; + default: + break; + } + + temp0 = (tp.degc_cali * 10 / 2); + temp1 = ((10000 * 100000 / 4096 / tp.gain) * + tp.oe + tb_roomt * 10) * 15 / 18; + + if (!tp.o_slope_sign) + temp2 = temp1 * 100 / (1534 + tp.o_slope * 10); + else + temp2 = temp1 * 100 / (1534 - tp.o_slope * 10); + + svsb->bts = (temp0 + temp2 - 250) * 4 / 10; + } + + return true; +} + +static bool svs_is_supported(struct svs_platform *svsp) +{ + struct nvmem_cell *cell; + + /* Get svs efuse by nvmem */ + cell = nvmem_cell_get(svsp->dev, "svs-calibration-data"); + if (IS_ERR_OR_NULL(cell)) { + dev_err(svsp->dev, + "no \"svs-calibration-data\" from dts? disable svs\n"); + return false; + } + + svsp->efuse = (u32 *)nvmem_cell_read(cell, &svsp->efuse_num); + svsp->efuse_num /= sizeof(u32); + nvmem_cell_put(cell); + + if (!svsp->fake_efuse && !svsp->efuse[svsp->efuse_check]) { + dev_err(svsp->dev, "svs_efuse[%u] = 0x%x?\n", + svsp->efuse_check, svsp->efuse[svsp->efuse_check]); + return false; + } + + return svsp->efuse_parsing(svsp); +} + +static int svs_suspend(struct device *dev) +{ + struct svs_platform *svsp = dev_get_drvdata(dev); + struct svs_bank *svsb; + unsigned long flags; + int ret; + u32 idx; + + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + + /* Wait if svs_isr() is still in process. */ + spin_lock_irqsave(&mtk_svs_lock, flags); + svsp->pbank = svsb; + svs_switch_bank(svsp); + svs_writel(svsp, SVSB_EN_OFF, SVSEN); + svs_writel(svsp, SVSB_INTSTS_CLEAN, INTSTS); + spin_unlock_irqrestore(&mtk_svs_lock, flags); + + svsb->suspended = true; + if (svsb->phase != SVSB_PHASE_INIT01) { + svsb->phase = SVSB_PHASE_ERROR; + svs_adjust_pm_opp_volts(svsb, true); + } + } + + if (svsp->rst) { + ret = reset_control_assert(svsp->rst); + if (ret) { + dev_err(svsp->dev, "cannot assert reset %d\n", ret); + return ret; + } + } + + clk_disable_unprepare(svsp->main_clk); + + return 0; +} + +static int svs_resume(struct device *dev) +{ + struct svs_platform *svsp = dev_get_drvdata(dev); + struct svs_bank *svsb; + int ret; + u32 idx; + + ret = clk_prepare_enable(svsp->main_clk); + if (ret) { + dev_err(svsp->dev, "cannot enable main_clk, disable svs\n"); + return ret; + } + + if (svsp->rst) { + ret = reset_control_deassert(svsp->rst); + if (ret) { + dev_err(svsp->dev, "cannot deassert reset %d\n", ret); + return ret; + } + } + + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + svsb->suspended = false; + } + + ret = svs_init02(svsp); + if (ret) + return ret; + + svs_mon_mode(svsp); + + return 0; +} + +static struct svs_bank svs_mt8183_banks[4] = { + { + .sw_id = SVSB_CPU_LITTLE, + .cpu_id = 0, + .tzone_name = "tzts4", + .buck_name = "proc", + .pd_req = false, + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY, + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02, + .opp_count = 16, + .freq_base = 1989000000, + .vboot = 0x30, + .volt_step = 6250, + .volt_base = 500000, + .volt_offset = 0, + .vmax = 0x64, + .vmin = 0x18, + .dthi = 0x1, + .dtlo = 0xfe, + .det_window = 0xa28, + .det_max = 0xffff, + .age_config = 0x555555, + .agem = 0, + .dc_config = 0x555555, + .dvt_fixed = 0x7, + .vco = 0x10, + .chk_shift = 0x77, + .temp_upper_bound = 0x64, + .temp_lower_bound = 0xb2, + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX, + .tzone_low_temp = 25000, + .tzone_low_temp_offset = 0, + .core_sel = 0x8fff0000, + .int_st = BIT(0), + .ctl0 = 0x00010001, + }, + { + .sw_id = SVSB_CPU_BIG, + .cpu_id = 4, + .tzone_name = "tzts5", + .buck_name = "proc", + .pd_req = false, + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY, + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02, + .opp_count = 16, + .freq_base = 1989000000, + .vboot = 0x30, + .volt_step = 6250, + .volt_base = 500000, + .volt_offset = 0, + .vmax = 0x58, + .vmin = 0x10, + .dthi = 0x1, + .dtlo = 0xfe, + .det_window = 0xa28, + .det_max = 0xffff, + .age_config = 0x555555, + .agem = 0, + .dc_config = 0x555555, + .dvt_fixed = 0x7, + .vco = 0x10, + .chk_shift = 0x77, + .temp_upper_bound = 0x64, + .temp_lower_bound = 0xb2, + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX, + .tzone_low_temp = 25000, + .tzone_low_temp_offset = 0, + .core_sel = 0x8fff0001, + .int_st = BIT(1), + .ctl0 = 0x00000001, + }, + { + .sw_id = SVSB_CCI, + .tzone_name = "tzts4", + .buck_name = "proc", + .pd_req = false, + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY, + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02, + .opp_count = 16, + .freq_base = 1196000000, + .vboot = 0x30, + .volt_step = 6250, + .volt_base = 500000, + .volt_offset = 0, + .vmax = 0x64, + .vmin = 0x18, + .dthi = 0x1, + .dtlo = 0xfe, + .det_window = 0xa28, + .det_max = 0xffff, + .age_config = 0x555555, + .agem = 0, + .dc_config = 0x555555, + .dvt_fixed = 0x7, + .vco = 0x10, + .chk_shift = 0x77, + .temp_upper_bound = 0x64, + .temp_lower_bound = 0xb2, + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX, + .tzone_low_temp = 25000, + .tzone_low_temp_offset = 0, + .core_sel = 0x8fff0002, + .int_st = BIT(2), + .ctl0 = 0x00100003, + }, + { + .sw_id = SVSB_GPU, + .tzone_name = "tzts2", + .buck_name = "mali", + .pd_req = true, + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY, + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02 | + SVSB_MODE_MON, + .opp_count = 16, + .freq_base = 900000000, + .vboot = 0x30, + .volt_step = 6250, + .volt_base = 500000, + .volt_offset = 0, + .vmax = 0x40, + .vmin = 0x14, + .dthi = 0x1, + .dtlo = 0xfe, + .det_window = 0xa28, + .det_max = 0xffff, + .age_config = 0x555555, + .agem = 0, + .dc_config = 0x555555, + .dvt_fixed = 0x3, + .vco = 0x10, + .chk_shift = 0x77, + .temp_upper_bound = 0x64, + .temp_lower_bound = 0xb2, + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX, + .tzone_low_temp = 25000, + .tzone_low_temp_offset = 3, + .core_sel = 0x8fff0003, + .int_st = BIT(3), + .ctl0 = 0x00050001, + }, +}; + +static int svs_get_svs_mt8183_platform_data(struct svs_platform *svsp) +{ + struct device *dev; + struct svs_bank *svsb; + u32 idx; + + svsp->name = "mt8183-svs"; + svsp->banks = svs_mt8183_banks; + svsp->efuse_parsing = svs_mt8183_efuse_parsing; + svsp->set_freqs_pct = svs_set_freqs_pct_v2; + svsp->get_vops = svs_get_vops_v2; + svsp->regs = svs_regs_v2; + svsp->irqflags = IRQF_TRIGGER_LOW | IRQF_ONESHOT; + svsp->rst = NULL; + svsp->fake_efuse = false; + svsp->bank_num = 4; + svsp->efuse_check = 2; + + dev = svs_add_device_link(svsp, "thermal"); + if (IS_ERR(dev)) + return PTR_ERR(dev); + + for (idx = 0; idx < svsp->bank_num; idx++) { + svsb = &svsp->banks[idx]; + + switch (svsb->sw_id) { + case SVSB_CPU_LITTLE: + case SVSB_CPU_BIG: + svsb->opp_dev = get_cpu_device(svsb->cpu_id); + break; + case SVSB_CCI: + svsb->opp_dev = svs_add_device_link(svsp, "cci"); + break; + case SVSB_GPU: + svsb->opp_dev = svs_add_device_link(svsp, "mali"); + svsb->pd_dev = svs_add_device_link(svsp, + "mali_gpu_core2"); + if (IS_ERR(svsb->pd_dev)) + return PTR_ERR(svsb->pd_dev); + break; + default: + WARN_ON(1); + return -EINVAL; + } + + if (IS_ERR(svsb->opp_dev)) + return PTR_ERR(svsb->opp_dev); + } + + return 0; +} + +static const struct of_device_id mtk_svs_of_match[] = { + { + .compatible = "mediatek,mt8183-svs", + .data = &svs_get_svs_mt8183_platform_data, + }, { + /* Sentinel */ + }, +}; + +static int svs_probe(struct platform_device *pdev) +{ + int (*svs_get_svs_platform_data)(struct svs_platform *svsp); + struct svs_platform *svsp; + unsigned int svsp_irq; + int ret; + + svsp = devm_kzalloc(&pdev->dev, sizeof(*svsp), GFP_KERNEL); + if (!svsp) + return -ENOMEM; + + svs_get_svs_platform_data = of_device_get_match_data(&pdev->dev); + if (!svs_get_svs_platform_data) { + dev_err(svsp->dev, "no svs platform data? why?\n"); + return -EPERM; + } + + svsp->dev = &pdev->dev; + ret = svs_get_svs_platform_data(svsp); + if (ret) { + dev_err_probe(svsp->dev, ret, "fail to get svsp data\n"); + return ret; + } + + if (!svs_is_supported(svsp)) { + dev_notice(svsp->dev, "svs is not supported\n"); + return -EPERM; + } + + ret = svs_resource_setup(svsp); + if (ret) { + dev_err(svsp->dev, "svs resource setup fail: %d\n", ret); + return ret; + } + + svsp_irq = irq_of_parse_and_map(svsp->dev->of_node, 0); + ret = devm_request_threaded_irq(svsp->dev, svsp_irq, NULL, svs_isr, + svsp->irqflags, svsp->name, svsp); + if (ret) { + dev_err(svsp->dev, "register irq(%d) failed: %d\n", + svsp_irq, ret); + return ret; + } + + svsp->main_clk = devm_clk_get(svsp->dev, "main"); + if (IS_ERR(svsp->main_clk)) { + dev_err(svsp->dev, "failed to get clock: %ld\n", + PTR_ERR(svsp->main_clk)); + return PTR_ERR(svsp->main_clk); + } + + ret = clk_prepare_enable(svsp->main_clk); + if (ret) { + dev_err(svsp->dev, "cannot enable main clk: %d\n", ret); + return ret; + } + + svsp->base = of_iomap(svsp->dev->of_node, 0); + if (IS_ERR_OR_NULL(svsp->base)) { + dev_err(svsp->dev, "cannot find svs register base\n"); + ret = -EINVAL; + goto svs_probe_clk_disable; + } + + ret = svs_start(svsp); + if (ret) { + dev_err(svsp->dev, "svs start fail: %d\n", ret); + goto svs_probe_iounmap; + } + + return 0; + +svs_probe_iounmap: + iounmap(svsp->base); + +svs_probe_clk_disable: + clk_disable_unprepare(svsp->main_clk); + + return ret; +} + +static SIMPLE_DEV_PM_OPS(svs_pm_ops, svs_suspend, svs_resume); + +static struct platform_driver svs_driver = { + .probe = svs_probe, + .driver = { + .name = "mtk-svs", + .pm = &svs_pm_ops, + .of_match_table = of_match_ptr(mtk_svs_of_match), + }, +}; + +module_platform_driver(svs_driver); + +MODULE_AUTHOR("Roger Lu <roger.lu@mediatek.com>"); +MODULE_DESCRIPTION("MediaTek SVS driver"); +MODULE_LICENSE("GPL v2");
The Smart Voltage Scaling(SVS) engine is a piece of hardware which calculats suitable SVS bank voltages to OPP voltage table. Then, DVFS driver could apply those SVS bank voltages to PMIC/Buck when receiving OPP_EVENT_ADJUST_VOLTAGE. Signed-off-by: Roger Lu <roger.lu@mediatek.com> --- drivers/soc/mediatek/Kconfig | 10 + drivers/soc/mediatek/Makefile | 1 + drivers/soc/mediatek/mtk-svs.c | 1748 ++++++++++++++++++++++++++++++++ 3 files changed, 1759 insertions(+) create mode 100644 drivers/soc/mediatek/mtk-svs.c