| Message ID | 20210103111744.34989-2-samuel@sholland.org (mailing list archive) |
|---|---|
| State | Accepted |
| Delegated to: | Netdev Maintainers |
| Headers | show |
| Series | Fixes for dwmac-sun8i suspend/resume | expand |
| Context | Check | Description |
|---|---|---|
| netdev/cover_letter | success | Link |
| netdev/fixes_present | success | Link |
| netdev/patch_count | success | Link |
| netdev/tree_selection | success | Clearly marked for net |
| netdev/subject_prefix | success | Link |
| netdev/cc_maintainers | warning | 3 maintainers not CCed: linux-stm32@st-md-mailman.stormreply.com clabbe.montjoie@gmail.com mcoquelin.stm32@gmail.com |
| netdev/source_inline | success | Was 0 now: 0 |
| netdev/verify_signedoff | success | Link |
| netdev/module_param | success | Was 0 now: 0 |
| netdev/build_32bit | success | Errors and warnings before: 0 this patch: 0 |
| netdev/kdoc | success | Errors and warnings before: 0 this patch: 0 |
| netdev/verify_fixes | success | Link |
| netdev/checkpatch | success | total: 0 errors, 0 warnings, 0 checks, 65 lines checked |
| netdev/build_allmodconfig_warn | success | Errors and warnings before: 0 this patch: 0 |
| netdev/header_inline | success | Link |
| netdev/stable | success | Stable not CCed |
On Sun, Jan 3, 2021 at 7:17 PM Samuel Holland <samuel@sholland.org> wrote: > > stmmac_pltfr_remove does three things in one function, making it > inapproprate for unwinding the steps in the probe function. Currently, > a failure before the call to stmmac_dvr_probe would leak OF node > references due to missing a call to stmmac_remove_config_dt. And an > error in stmmac_dvr_probe would cause the driver to attempt to remove a > netdevice that was never added. Fix these by reordering the init and > splitting out the error handling steps. > > Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i") > Fixes: 40a1dcee2d18 ("net: ethernet: dwmac-sun8i: Use the correct function in exit path") > Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Chen-Yu Tsai <wens@csie.org>
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c index 58e0511badba..b20f261fce5b 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c @@ -1134,10 +1134,6 @@ static int sun8i_dwmac_probe(struct platform_device *pdev) if (ret) return ret; - plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - gmac = devm_kzalloc(dev, sizeof(*gmac), GFP_KERNEL); if (!gmac) return -ENOMEM; @@ -1201,11 +1197,15 @@ static int sun8i_dwmac_probe(struct platform_device *pdev) ret = of_get_phy_mode(dev->of_node, &interface); if (ret) return -EINVAL; - plat_dat->interface = interface; + + plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); /* platform data specifying hardware features and callbacks. * hardware features were copied from Allwinner drivers. */ + plat_dat->interface = interface; plat_dat->rx_coe = STMMAC_RX_COE_TYPE2; plat_dat->tx_coe = 1; plat_dat->has_sun8i = true; @@ -1216,7 +1216,7 @@ static int sun8i_dwmac_probe(struct platform_device *pdev) ret = sun8i_dwmac_init(pdev, plat_dat->bsp_priv); if (ret) - return ret; + goto dwmac_deconfig; ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); if (ret) @@ -1230,7 +1230,7 @@ static int sun8i_dwmac_probe(struct platform_device *pdev) if (gmac->variant->soc_has_internal_phy) { ret = get_ephy_nodes(priv); if (ret) - goto dwmac_exit; + goto dwmac_remove; ret = sun8i_dwmac_register_mdio_mux(priv); if (ret) { dev_err(&pdev->dev, "Failed to register mux\n"); @@ -1239,15 +1239,20 @@ static int sun8i_dwmac_probe(struct platform_device *pdev) } else { ret = sun8i_dwmac_reset(priv); if (ret) - goto dwmac_exit; + goto dwmac_remove; } return ret; dwmac_mux: sun8i_dwmac_unset_syscon(gmac); +dwmac_remove: + stmmac_dvr_remove(&pdev->dev); dwmac_exit: - stmmac_pltfr_remove(pdev); -return ret; + sun8i_dwmac_exit(pdev, gmac); +dwmac_deconfig: + stmmac_remove_config_dt(pdev, plat_dat); + + return ret; } static const struct of_device_id sun8i_dwmac_match[] = {
stmmac_pltfr_remove does three things in one function, making it inapproprate for unwinding the steps in the probe function. Currently, a failure before the call to stmmac_dvr_probe would leak OF node references due to missing a call to stmmac_remove_config_dt. And an error in stmmac_dvr_probe would cause the driver to attempt to remove a netdevice that was never added. Fix these by reordering the init and splitting out the error handling steps. Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i") Fixes: 40a1dcee2d18 ("net: ethernet: dwmac-sun8i: Use the correct function in exit path") Signed-off-by: Samuel Holland <samuel@sholland.org> --- .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 25 +++++++++++-------- 1 file changed, 15 insertions(+), 10 deletions(-)