| Message ID | 20210130105717.2628781-3-vincent.knecht@mailoo.org (mailing list archive) |
|---|---|
| State | Accepted |
| Headers | show |
| Series | Alcatel Idol 3 (4.7") smartphone support | expand |
On Sat, Jan 30, 2021 at 11:57:11AM +0100, Vincent Knecht wrote: > The Alcatel Idol 3 (4.7") is a smartphone based on MSM8916. > Add a device tree with support for USB, eMMC, SD-Card, WiFi, > BT, power/volume buttons, vibrator and the following sensors: > magnetometer, accelerometer, gyroscope, ambient light+proximity > > Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org> Reviewed-by: Stephan Gerhold <stephan@gerhold.net> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/msm8916-alcatel-idol347.dts | 291 ++++++++++++++++++ > 2 files changed, 292 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 59455db7b493..0feeedb712cc 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts > new file mode 100644 > index 000000000000..540b1fa4b260 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts > @@ -0,0 +1,291 @@ > +// SPDX-License-Identifier: GPL-2.0-only > + > +/dts-v1/; > + > +#include "msm8916-pm8916.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +/ { > + model = "Alcatel OneTouch Idol 3 (4.7)"; > + compatible = "alcatel,idol347", "qcom,msm8916"; > + > + aliases { > + serial0 = &blsp1_uart2; > + }; > + > + chosen { > + stdout-path = "serial0"; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_keys_default>; > + > + label = "GPIO Buttons"; > + > + volume-up { > + label = "Volume Up"; > + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + }; > + }; > + > + usb_id: usb-id { > + compatible = "linux,extcon-usb-gpio"; > + id-gpio = <&msmgpio 69 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&usb_id_default>; > + }; > +}; > + > +&blsp1_uart2 { > + status = "okay"; > +}; > + > +&blsp_i2c5 { > + status = "okay"; > + > + magnetometer@c { > + compatible = "asahi-kasei,ak09911"; > + reg = <0x0c>; > + vdd-supply = <&pm8916_l17>; > + vid-supply = <&pm8916_l6>; > + reset-gpios = <&msmgpio 8 GPIO_ACTIVE_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&mag_reset_default>; > + mount-matrix = "0", "1", "0", > + "-1", "0", "0", > + "0", "0", "1"; > + }; > + > + accelerometer@f { > + compatible = "kionix,kxtj21009"; > + reg = <0x0f>; > + vdd-supply = <&pm8916_l17>; > + vddio-supply = <&pm8916_l6>; > + interrupt-parent = <&msmgpio>; > + interrupts = <31 IRQ_TYPE_EDGE_RISING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&accel_int_default>; > + mount-matrix = "-1", "0", "0", > + "0", "1", "0", > + "0", "0", "-1"; > + }; > + > + proximity@48 { > + compatible = "sensortek,stk3310"; > + reg = <0x48>; > + interrupt-parent = <&msmgpio>; > + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&proximity_int_default>; > + }; > + > + gyroscope@68 { > + compatible = "bosch,bmg160"; > + reg = <0x68>; > + vdd-supply = <&pm8916_l17>; > + vddio-supply = <&pm8916_l6>; > + interrupt-parent = <&msmgpio>; > + interrupts = <97 IRQ_TYPE_EDGE_RISING>, > + <98 IRQ_TYPE_EDGE_RISING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&gyro_int_default>; > + }; > +}; > + > +&pm8916_resin { > + status = "okay"; > + linux,code = <KEY_VOLUMEDOWN>; > +}; > + > +&pm8916_vib { > + status = "okay"; > +}; > + > +&pronto { > + status = "okay"; > +}; > + > +&sdhc_1 { > + status = "okay"; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; > + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; > +}; > + > +&sdhc_2 { > + status = "okay"; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; > + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; > + > + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; > +}; > + > +&usb { > + status = "okay"; > + extcon = <&usb_id>, <&usb_id>; > +}; > + > +&usb_hs_phy { > + extcon = <&usb_id>; > +}; > + > +&smd_rpm_regulators { > + vdd_l1_l2_l3-supply = <&pm8916_s3>; > + vdd_l4_l5_l6-supply = <&pm8916_s4>; > + vdd_l7-supply = <&pm8916_s4>; > + > + s3 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1300000>; > + }; > + > + s4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2100000>; > + }; > + > + l1 { > + regulator-min-microvolt = <1225000>; > + regulator-max-microvolt = <1225000>; > + }; > + > + l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + l4 { > + regulator-min-microvolt = <2050000>; > + regulator-max-microvolt = <2050000>; > + }; > + > + l5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l8 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2900000>; > + }; > + > + l9 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l10 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2800000>; > + }; > + > + l11 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + regulator-allow-set-load; > + regulator-system-load = <200000>; > + }; > + > + l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + l13 { > + regulator-min-microvolt = <3075000>; > + regulator-max-microvolt = <3075000>; > + }; > + > + l14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l16 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l17 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > + > + l18 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2700000>; > + }; > +}; > + > +&msmgpio { > + accel_int_default: accel-int-default { > + pins = "gpio31"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-disable; > + }; > + > + gpio_keys_default: gpio-keys-default { > + pins = "gpio107"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + gyro_int_default: gyro-int-default { > + pins = "gpio97", "gpio98"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-disable; > + }; > + > + mag_reset_default: mag-reset-default { > + pins = "gpio8"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-disable; > + }; > + > + proximity_int_default: proximity-int-default { > + pins = "gpio12"; > + function = "gpio"; > + > + drive-strength = <6>; > + bias-pull-up; > + }; > + > + usb_id_default: usb-id-default { > + pins = "gpio69"; > + function = "gpio"; > + > + drive-strength = <8>; > + bias-pull-up; > + }; > +}; > -- > 2.29.2 > > >
On 30.01.2021 11:57, Vincent Knecht wrote: > The Alcatel Idol 3 (4.7") is a smartphone based on MSM8916. > Add a device tree with support for USB, eMMC, SD-Card, WiFi, > BT, power/volume buttons, vibrator and the following sensors: > magnetometer, accelerometer, gyroscope, ambient light+proximity > > Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org> > Reviewed-by: Stephan Gerhold <stephan@gerhold.net> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/msm8916-alcatel-idol347.dts | 291 ++++++++++++++++++ > 2 files changed, 292 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 59455db7b493..0feeedb712cc 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts > new file mode 100644 > index 000000000000..540b1fa4b260 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts > @@ -0,0 +1,291 @@ > +// SPDX-License-Identifier: GPL-2.0-only > + > +/dts-v1/; > + > +#include "msm8916-pm8916.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +/ { > + model = "Alcatel OneTouch Idol 3 (4.7)"; > + compatible = "alcatel,idol347", "qcom,msm8916"; > + > + aliases { > + serial0 = &blsp1_uart2; > + }; > + > + chosen { > + stdout-path = "serial0"; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_keys_default>; > + > + label = "GPIO Buttons"; > + > + volume-up { > + label = "Volume Up"; > + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + }; > + }; > + > + usb_id: usb-id { > + compatible = "linux,extcon-usb-gpio"; > + id-gpio = <&msmgpio 69 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&usb_id_default>; > + }; > +}; > + > +&blsp1_uart2 { > + status = "okay"; > +}; > + > +&blsp_i2c5 { > + status = "okay"; > + > + magnetometer@c { > + compatible = "asahi-kasei,ak09911"; > + reg = <0x0c>; > + vdd-supply = <&pm8916_l17>; > + vid-supply = <&pm8916_l6>; > + reset-gpios = <&msmgpio 8 GPIO_ACTIVE_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&mag_reset_default>; > + mount-matrix = "0", "1", "0", > + "-1", "0", "0", > + "0", "0", "1"; > + }; > + > + accelerometer@f { > + compatible = "kionix,kxtj21009"; > + reg = <0x0f>; > + vdd-supply = <&pm8916_l17>; > + vddio-supply = <&pm8916_l6>; > + interrupt-parent = <&msmgpio>; > + interrupts = <31 IRQ_TYPE_EDGE_RISING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&accel_int_default>; > + mount-matrix = "-1", "0", "0", > + "0", "1", "0", > + "0", "0", "-1"; > + }; > + > + proximity@48 { > + compatible = "sensortek,stk3310"; > + reg = <0x48>; > + interrupt-parent = <&msmgpio>; > + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&proximity_int_default>; > + }; > + > + gyroscope@68 { > + compatible = "bosch,bmg160"; > + reg = <0x68>; > + vdd-supply = <&pm8916_l17>; > + vddio-supply = <&pm8916_l6>; > + interrupt-parent = <&msmgpio>; > + interrupts = <97 IRQ_TYPE_EDGE_RISING>, > + <98 IRQ_TYPE_EDGE_RISING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&gyro_int_default>; > + }; > +}; > + > +&pm8916_resin { > + status = "okay"; > + linux,code = <KEY_VOLUMEDOWN>; > +}; > + > +&pm8916_vib { > + status = "okay"; > +}; > + > +&pronto { > + status = "okay"; > +}; > + > +&sdhc_1 { > + status = "okay"; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; > + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; > +}; > + > +&sdhc_2 { > + status = "okay"; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; > + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; > + > + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; > +}; > + > +&usb { > + status = "okay"; > + extcon = <&usb_id>, <&usb_id>; > +}; > + > +&usb_hs_phy { > + extcon = <&usb_id>; > +}; > + > +&smd_rpm_regulators { > + vdd_l1_l2_l3-supply = <&pm8916_s3>; > + vdd_l4_l5_l6-supply = <&pm8916_s4>; > + vdd_l7-supply = <&pm8916_s4>; > + > + s3 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1300000>; > + }; > + > + s4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2100000>; > + }; > + > + l1 { > + regulator-min-microvolt = <1225000>; > + regulator-max-microvolt = <1225000>; > + }; > + > + l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + l4 { > + regulator-min-microvolt = <2050000>; > + regulator-max-microvolt = <2050000>; > + }; > + > + l5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l8 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2900000>; > + }; > + > + l9 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l10 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2800000>; > + }; > + > + l11 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + regulator-allow-set-load; > + regulator-system-load = <200000>; > + }; > + > + l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + l13 { > + regulator-min-microvolt = <3075000>; > + regulator-max-microvolt = <3075000>; > + }; > + > + l14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l16 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l17 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > + > + l18 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2700000>; > + }; > +}; > + > +&msmgpio { > + accel_int_default: accel-int-default { > + pins = "gpio31"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-disable; > + }; > + > + gpio_keys_default: gpio-keys-default { > + pins = "gpio107"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + gyro_int_default: gyro-int-default { > + pins = "gpio97", "gpio98"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-disable; > + }; > + > + mag_reset_default: mag-reset-default { > + pins = "gpio8"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-disable; > + }; > + > + proximity_int_default: proximity-int-default { > + pins = "gpio12"; > + function = "gpio"; > + > + drive-strength = <6>; > + bias-pull-up; > + }; > + > + usb_id_default: usb-id-default { > + pins = "gpio69"; > + function = "gpio"; > + > + drive-strength = <8>; > + bias-pull-up; > + }; > +}; > Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Konrad
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 59455db7b493..0feeedb712cc 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts new file mode 100644 index 000000000000..540b1fa4b260 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts @@ -0,0 +1,291 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Alcatel OneTouch Idol 3 (4.7)"; + compatible = "alcatel,idol347", "qcom,msm8916"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&msmgpio 69 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&blsp_i2c5 { + status = "okay"; + + magnetometer@c { + compatible = "asahi-kasei,ak09911"; + reg = <0x0c>; + vdd-supply = <&pm8916_l17>; + vid-supply = <&pm8916_l6>; + reset-gpios = <&msmgpio 8 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&mag_reset_default>; + mount-matrix = "0", "1", "0", + "-1", "0", "0", + "0", "0", "1"; + }; + + accelerometer@f { + compatible = "kionix,kxtj21009"; + reg = <0x0f>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + interrupt-parent = <&msmgpio>; + interrupts = <31 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_int_default>; + mount-matrix = "-1", "0", "0", + "0", "1", "0", + "0", "0", "-1"; + }; + + proximity@48 { + compatible = "sensortek,stk3310"; + reg = <0x48>; + interrupt-parent = <&msmgpio>; + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&proximity_int_default>; + }; + + gyroscope@68 { + compatible = "bosch,bmg160"; + reg = <0x68>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + interrupt-parent = <&msmgpio>; + interrupts = <97 IRQ_TYPE_EDGE_RISING>, + <98 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_int_default>; + }; +}; + +&pm8916_resin { + status = "okay"; + linux,code = <KEY_VOLUMEDOWN>; +}; + +&pm8916_vib { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; + + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; +}; + +&usb { + status = "okay"; + extcon = <&usb_id>, <&usb_id>; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + regulator-system-load = <200000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + accel_int_default: accel-int-default { + pins = "gpio31"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + gpio_keys_default: gpio-keys-default { + pins = "gpio107"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + gyro_int_default: gyro-int-default { + pins = "gpio97", "gpio98"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + mag_reset_default: mag-reset-default { + pins = "gpio8"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + proximity_int_default: proximity-int-default { + pins = "gpio12"; + function = "gpio"; + + drive-strength = <6>; + bias-pull-up; + }; + + usb_id_default: usb-id-default { + pins = "gpio69"; + function = "gpio"; + + drive-strength = <8>; + bias-pull-up; + }; +};
The Alcatel Idol 3 (4.7") is a smartphone based on MSM8916. Add a device tree with support for USB, eMMC, SD-Card, WiFi, BT, power/volume buttons, vibrator and the following sensors: magnetometer, accelerometer, gyroscope, ambient light+proximity Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/msm8916-alcatel-idol347.dts | 291 ++++++++++++++++++ 2 files changed, 292 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts