[V2] arm64: dts: sc7280: Add qspi, qupv3_0 and qupv3_1 nodes

Message ID	20210422150556.450-1-rojay@codeaurora.org (mailing list archive)
State	Superseded
Headers	show Return-Path: <linux-arm-msm-owner@kernel.org> From: Roja Rani Yarubandi <rojay@codeaurora.org> To: agross@kernel.org, bjorn.andersson@linaro.org, robh+dt@kernel.org Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Rajendra Nayak <rnayak@codeaurora.org>, saiprakash.ranjan@codeaurora.org, msavaliy@qti.qualcomm.com, Roja Rani Yarubandi <rojay@codeaurora.org> Subject: [PATCH V2] arm64: dts: sc7280: Add qspi, qupv3_0 and qupv3_1 nodes Date: Thu, 22 Apr 2021 20:35:56 +0530 Message-Id: <20210422150556.450-1-rojay@codeaurora.org> MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Precedence: bulk
Series	[V2] arm64: dts: sc7280: Add qspi, qupv3_0 and qupv3_1 nodes \| expand [V2] arm64: dts: sc7280: Add qspi, qupv3_0 and qupv3_1 nodes

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts index 54d2cb365b71..b1e948a72eb1 100644 --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts @@ -15,6 +15,7 @@ / { aliases { serial0 = &uart5; + hsuart0 = &uart7; }; chosen { @@ -234,26 +235,140 @@ vreg_l6e_0p8: ldo6 { }; }; +&qspi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + + /* TODO: Increase frequency after testing */ + spi-max-frequency = <25000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; +}; + &qupv3_id_0 { status = "okay"; }; +&qupv3_id_1 { + status = "okay"; +}; + &uart5 { status = "okay"; }; +&uart7 { + status = "okay"; + + /delete-property/interrupts; + interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>, + <&tlmm 31 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default", "sleep"; + pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>; +}; + /* PINCTRL - additions to nodes defined in sc7280.dtsi */ -&qup_uart5_default { - tx { - pins = "gpio46"; - drive-strength = <2>; - bias-disable; +&qspi_cs0 { + bias-disable; +}; + +&qspi_clk { + bias-disable; +}; + +&qspi_data01 { + /* High-Z when no transfers; nice to park the lines */ + bias-pull-up; +}; + +&qup_uart5_tx { + drive-strength = <2>; + bias-disable; +}; + +&qup_uart5_rx { + drive-strength = <2>; + bias-pull-up; +}; + +&qup_uart7_cts { + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + bias-pull-down; +}; + +&qup_uart7_rts { + /* We'll drive RTS, so no pull */ + drive-strength = <2>; + bias-disable; +}; + +&qup_uart7_tx { + /* We'll drive TX, so no pull */ + drive-strength = <2>; + bias-disable; +}; + +&qup_uart7_rx { + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module is + * in tri-state (module powered off or not driving the + * signal yet). + */ + bias-pull-up; +}; + +&tlmm { + qup_uart7_sleep_cts: qup-uart7-sleep-cts { + pins = "gpio28"; + function = "gpio"; + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + bias-pull-down; + }; + + qup_uart7_sleep_rts: qup-uart7-sleep-rts { + pins = "gpio29"; + function = "gpio"; + /* + * Configure pull-down on RTS. As RTS is active low + * signal, pull it low to indicate the BT SoC that it + * can wakeup the system anytime from suspend state by + * pulling RX low (by sending wakeup bytes). + */ + bias-pull-down; + }; + + qup_uart7_sleep_tx: qup-uart7-sleep-tx { + pins = "gpio30"; + function = "gpio"; + /* + * Configure pull-up on TX when it isn't actively driven + * to prevent BT SoC from receiving garbage during sleep. + */ + bias-pull-up; }; - rx { - pins = "gpio47"; - drive-strength = <2>; + qup_uart7_sleep_rx: qup-uart7-sleep-rx { + pins = "gpio31"; + function = "gpio"; + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module + * is floating which may cause spurious wakeups. + */ bias-pull-up; }; }; diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index 2cc478553935..42bb2dda9047 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -293,6 +293,25 @@ ipcc: mailbox@408000 { #mbox-cells = <2>; }; + qup_opp_table: qup-opp-table { + compatible = "operating-points-v2"; + + opp-75000000 { + opp-hz = /bits/ 64 <75000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-128000000 { + opp-hz = /bits/ 64 <128000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + qupv3_id_0: geniqup@9c0000 { compatible = "qcom,geni-se-qup"; reg = <0 0x009c0000 0 0x2000>; @@ -302,575 +321,2111 @@ qupv3_id_0: geniqup@9c0000 { #address-cells = <2>; #size-cells = <2>; ranges; + iommus = <&apps_smmu 0x123 0x0>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>; + interconnect-names = "qup-core"; status = "disabled"; - uart5: serial@994000 { - compatible = "qcom,geni-debug-uart"; - reg = <0 0x00994000 0 0x4000>; + i2c0: i2c@980000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00980000 0 0x4000>; clock-names = "se"; - clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; pinctrl-names = "default"; - pinctrl-0 = <&qup_uart5_default>; - interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-0 = <&qup_i2c0_data_clk>; + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>, + <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; status = "disabled"; }; - }; - stm@6002000 { - compatible = "arm,coresight-stm", "arm,primecell"; - reg = <0 0x06002000 0 0x1000>, - <0 0x16280000 0 0x180000>; - reg-names = "stm-base", "stm-stimulus-base"; - - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; - - out-ports { - port { - stm_out: endpoint { - remote-endpoint = <&funnel0_in7>; - }; - }; + spi0: spi@980000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00980000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>, <&qup_spi0_cs_gpio>; + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; }; - }; - - funnel@6041000 { - compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; - reg = <0 0x06041000 0 0x1000>; - - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; - out-ports { - port { - funnel0_out: endpoint { - remote-endpoint = <&merge_funnel_in0>; - }; - }; + uart0: serial@980000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00980000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>, <&qup_uart0_tx>, <&qup_uart0_rx>; + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; }; - in-ports { + i2c1: i2c@984000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00984000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c1_data_clk>; + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; - - port@7 { - reg = <7>; - funnel0_in7: endpoint { - remote-endpoint = <&stm_out>; - }; - }; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>, + <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; }; - }; - - funnel@6042000 { - compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; - reg = <0 0x06042000 0 0x1000>; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; + spi1: spi@984000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00984000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>, <&qup_spi1_cs_gpio>; + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; - out-ports { - port { - funnel1_out: endpoint { - remote-endpoint = <&merge_funnel_in1>; - }; - }; + uart1: serial@984000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00984000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart1_cts>, <&qup_uart1_rts>, <&qup_uart1_tx>, <&qup_uart1_rx>; + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; }; - in-ports { + i2c2: i2c@988000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00988000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c2_data_clk>; + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; - - port@4 { - reg = <4>; - funnel1_in4: endpoint { - remote-endpoint = <&apss_merge_funnel_out>; - }; - }; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>, + <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; }; - }; - - funnel@6045000 { - compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; - reg = <0 0x06045000 0 0x1000>; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; + spi2: spi@988000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00988000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>, <&qup_spi2_cs_gpio>; + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; - out-ports { - port { - merge_funnel_out: endpoint { - remote-endpoint = <&swao_funnel_in>; - }; - }; + uart2: serial@988000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00988000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart2_cts>, <&qup_uart2_rts>, <&qup_uart2_tx>, <&qup_uart2_rx>; + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; }; - in-ports { + i2c3: i2c@98c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x0098c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c3_data_clk>; + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>, + <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; + }; - port@0 { - reg = <0>; - merge_funnel_in0: endpoint { - remote-endpoint = <&funnel0_out>; - }; - }; + spi3: spi@98c000 { + compatible = "qcom,geni-spi"; + reg = <0 0x0098c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>, <&qup_spi3_cs_gpio>; + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; - port@1 { - reg = <1>; - merge_funnel_in1: endpoint { - remote-endpoint = <&funnel1_out>; - }; - }; + uart3: serial@98c000 { + compatible = "qcom,geni-uart"; + reg = <0 0x0098c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart3_cts>, <&qup_uart3_rts>, <&qup_uart3_tx>, <&qup_uart3_rx>; + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; }; - }; - replicator@6046000 { - compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; - reg = <0 0x06046000 0 0x1000>; + i2c4: i2c@990000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00990000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c4_data_clk>; + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>, + <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; + }; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; + spi4: spi@990000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00990000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>, <&qup_spi4_cs_gpio>; + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; - out-ports { - port { - replicator_out: endpoint { - remote-endpoint = <&etr_in>; - }; - }; + uart4: serial@990000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00990000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart4_cts>, <&qup_uart4_rts>, <&qup_uart4_tx>, <&qup_uart4_rx>; + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; }; - in-ports { - port { - replicator_in: endpoint { - remote-endpoint = <&swao_replicator_out>; - }; - }; + i2c5: i2c@994000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00994000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c5_data_clk>; + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>, + <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; }; - }; - etr@6048000 { - compatible = "arm,coresight-tmc", "arm,primecell"; - reg = <0 0x06048000 0 0x1000>; - iommus = <&apps_smmu 0x04c0 0>; + spi5: spi@994000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00994000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>, <&qup_spi5_cs_gpio>; + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; - arm,scatter-gather; + uart5: serial@994000 { + compatible = "qcom,geni-debug-uart"; + reg = <0 0x00994000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart5_cts>, <&qup_uart5_rts>, <&qup_uart5_tx>, <&qup_uart5_rx>; + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; - in-ports { - port { - etr_in: endpoint { - remote-endpoint = <&replicator_out>; - }; - }; + i2c6: i2c@998000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00998000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c6_data_clk>; + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>, + <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; }; - }; - funnel@6b04000 { - compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; - reg = <0 0x06b04000 0 0x1000>; + spi6: spi@998000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00998000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>, <&qup_spi6_cs_gpio>; + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; + uart6: serial@998000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00998000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart6_cts>, <&qup_uart6_rts>, <&qup_uart6_tx>, <&qup_uart6_rx>; + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; - out-ports { - port { - swao_funnel_out: endpoint { - remote-endpoint = <&etf_in>; - }; - }; + i2c7: i2c@99c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x0099c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c7_data_clk>; + interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>, + <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; }; - in-ports { + spi7: spi@99c000 { + compatible = "qcom,geni-spi"; + reg = <0 0x0099c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>, <&qup_spi7_cs_gpio>; + interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; - port@7 { - reg = <7>; - swao_funnel_in: endpoint { - remote-endpoint = <&merge_funnel_out>; - }; - }; + uart7: serial@99c000 { + compatible = "qcom,geni-uart"; + reg = <0 0x0099c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart7_cts>, <&qup_uart7_rts>, <&qup_uart7_tx>, <&qup_uart7_rx>; + interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; }; }; - etf@6b05000 { - compatible = "arm,coresight-tmc", "arm,primecell"; - reg = <0 0x06b05000 0 0x1000>; + qupv3_id_1: geniqup@ac0000 { + compatible = "qcom,geni-se-qup"; + reg = <0 0x00ac0000 0 0x2000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + iommus = <&apps_smmu 0x43 0x0>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>; + interconnect-names = "qup-core"; + status = "disabled"; + + i2c8: i2c@a80000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a80000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c8_data_clk>; + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>, + <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; + }; + + spi8: spi@a80000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00a80000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>, <&qup_spi8_cs_gpio>; + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + uart8: serial@a80000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00a80000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart8_cts>, <&qup_uart8_rts>, <&qup_uart8_tx>, <&qup_uart8_rx>; + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + i2c9: i2c@a84000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a84000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c9_data_clk>; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>, + <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; + }; + + spi9: spi@a84000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00a84000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>, <&qup_spi9_cs_gpio>; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + uart9: serial@a84000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00a84000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart9_cts>, <&qup_uart9_rts>, <&qup_uart9_tx>, <&qup_uart9_rx>; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + i2c10: i2c@a88000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a88000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c10_data_clk>; + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>, + <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; + }; + + spi10: spi@a88000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00a88000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>, <&qup_spi10_cs_gpio>; + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + uart10: serial@a88000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00a88000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart10_cts>, <&qup_uart10_rts>, <&qup_uart10_tx>, <&qup_uart10_rx>; + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + i2c11: i2c@a8c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a8c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c11_data_clk>; + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>, + <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; + }; + + spi11: spi@a8c000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00a8c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>, <&qup_spi11_cs_gpio>; + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + uart11: serial@a8c000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00a8c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart11_cts>, <&qup_uart11_rts>, <&qup_uart11_tx>, <&qup_uart11_rx>; + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + i2c12: i2c@a90000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a90000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c12_data_clk>; + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>, + <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; + }; + + spi12: spi@a90000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00a90000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>, <&qup_spi12_cs_gpio>; + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + uart12: serial@a90000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00a90000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart12_cts>, <&qup_uart12_rts>, <&qup_uart12_tx>, <&qup_uart12_rx>; + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + i2c13: i2c@a94000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a94000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c13_data_clk>; + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>, + <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; + }; + + spi13: spi@a94000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00a94000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>, <&qup_spi13_cs_gpio>; + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + uart13: serial@a94000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00a94000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart13_cts>, <&qup_uart13_rts>, <&qup_uart13_tx>, <&qup_uart13_rx>; + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + i2c14: i2c@a98000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a98000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c14_data_clk>; + interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>, + <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; + }; + + spi14: spi@a98000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00a98000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>, <&qup_spi14_cs_gpio>; + interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + uart14: serial@a98000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00a98000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart14_cts>, <&qup_uart14_rts>, <&qup_uart14_tx>, <&qup_uart14_rx>; + interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + i2c15: i2c@a9c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a9c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c15_data_clk>; + interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>, + <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "qup-core", "qup-config", + "qup-memory"; + status = "disabled"; + }; + + spi15: spi@a9c000 { + compatible = "qcom,geni-spi"; + reg = <0 0x00a9c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>, <&qup_spi15_cs_gpio>; + interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + + uart15: serial@a9c000 { + compatible = "qcom,geni-uart"; + reg = <0 0x00a9c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart15_cts>, <&qup_uart15_rts>, <&qup_uart15_tx>, <&qup_uart15_rx>; + interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qup_opp_table>; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + status = "disabled"; + }; + }; + + stm@6002000 { + compatible = "arm,coresight-stm", "arm,primecell"; + reg = <0 0x06002000 0 0x1000>, + <0 0x16280000 0 0x180000>; + reg-names = "stm-base", "stm-stimulus-base"; clocks = <&aoss_qmp>; clock-names = "apb_pclk"; out-ports { port { - etf_out: endpoint { - remote-endpoint = <&swao_replicator_in>; - }; - }; - }; - - in-ports { - port { - etf_in: endpoint { - remote-endpoint = <&swao_funnel_out>; + stm_out: endpoint { + remote-endpoint = <&funnel0_in7>; }; }; }; }; - replicator@6b06000 { - compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; - reg = <0 0x06b06000 0 0x1000>; + funnel@6041000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06041000 0 0x1000>; clocks = <&aoss_qmp>; clock-names = "apb_pclk"; - qcom,replicator-loses-context; out-ports { port { - swao_replicator_out: endpoint { - remote-endpoint = <&replicator_in>; + funnel0_out: endpoint { + remote-endpoint = <&merge_funnel_in0>; }; }; }; in-ports { - port { - swao_replicator_in: endpoint { - remote-endpoint = <&etf_out>; + #address-cells = <1>; + #size-cells = <0>; + + port@7 { + reg = <7>; + funnel0_in7: endpoint { + remote-endpoint = <&stm_out>; }; }; }; }; - etm@7040000 { - compatible = "arm,coresight-etm4x", "arm,primecell"; - reg = <0 0x07040000 0 0x1000>; - - cpu = <&CPU0>; + funnel@6042000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06042000 0 0x1000>; clocks = <&aoss_qmp>; clock-names = "apb_pclk"; - arm,coresight-loses-context-with-cpu; - qcom,skip-power-up; out-ports { port { - etm0_out: endpoint { - remote-endpoint = <&apss_funnel_in0>; + funnel1_out: endpoint { + remote-endpoint = <&merge_funnel_in1>; }; }; }; - }; - etm@7140000 { - compatible = "arm,coresight-etm4x", "arm,primecell"; - reg = <0 0x07140000 0 0x1000>; - - cpu = <&CPU1>; - - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; - arm,coresight-loses-context-with-cpu; - qcom,skip-power-up; + in-ports { + #address-cells = <1>; + #size-cells = <0>; - out-ports { - port { - etm1_out: endpoint { - remote-endpoint = <&apss_funnel_in1>; + port@4 { + reg = <4>; + funnel1_in4: endpoint { + remote-endpoint = <&apss_merge_funnel_out>; }; }; }; }; - etm@7240000 { - compatible = "arm,coresight-etm4x", "arm,primecell"; - reg = <0 0x07240000 0 0x1000>; - - cpu = <&CPU2>; + funnel@6045000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06045000 0 0x1000>; clocks = <&aoss_qmp>; clock-names = "apb_pclk"; - arm,coresight-loses-context-with-cpu; - qcom,skip-power-up; out-ports { port { - etm2_out: endpoint { + merge_funnel_out: endpoint { + remote-endpoint = <&swao_funnel_in>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + merge_funnel_in0: endpoint { + remote-endpoint = <&funnel0_out>; + }; + }; + + port@1 { + reg = <1>; + merge_funnel_in1: endpoint { + remote-endpoint = <&funnel1_out>; + }; + }; + }; + }; + + replicator@6046000 { + compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; + reg = <0 0x06046000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + replicator_out: endpoint { + remote-endpoint = <&etr_in>; + }; + }; + }; + + in-ports { + port { + replicator_in: endpoint { + remote-endpoint = <&swao_replicator_out>; + }; + }; + }; + }; + + etr@6048000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x06048000 0 0x1000>; + iommus = <&apps_smmu 0x04c0 0>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,scatter-gather; + + in-ports { + port { + etr_in: endpoint { + remote-endpoint = <&replicator_out>; + }; + }; + }; + }; + + funnel@6b04000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06b04000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + swao_funnel_out: endpoint { + remote-endpoint = <&etf_in>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@7 { + reg = <7>; + swao_funnel_in: endpoint { + remote-endpoint = <&merge_funnel_out>; + }; + }; + }; + }; + + etf@6b05000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x06b05000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + etf_out: endpoint { + remote-endpoint = <&swao_replicator_in>; + }; + }; + }; + + in-ports { + port { + etf_in: endpoint { + remote-endpoint = <&swao_funnel_out>; + }; + }; + }; + }; + + replicator@6b06000 { + compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; + reg = <0 0x06b06000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + qcom,replicator-loses-context; + + out-ports { + port { + swao_replicator_out: endpoint { + remote-endpoint = <&replicator_in>; + }; + }; + }; + + in-ports { + port { + swao_replicator_in: endpoint { + remote-endpoint = <&etf_out>; + }; + }; + }; + }; + + etm@7040000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07040000 0 0x1000>; + + cpu = <&CPU0>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm0_out: endpoint { + remote-endpoint = <&apss_funnel_in0>; + }; + }; + }; + }; + + etm@7140000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07140000 0 0x1000>; + + cpu = <&CPU1>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm1_out: endpoint { + remote-endpoint = <&apss_funnel_in1>; + }; + }; + }; + }; + + etm@7240000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07240000 0 0x1000>; + + cpu = <&CPU2>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm2_out: endpoint { remote-endpoint = <&apss_funnel_in2>; }; }; }; - }; + }; + + etm@7340000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07340000 0 0x1000>; + + cpu = <&CPU3>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm3_out: endpoint { + remote-endpoint = <&apss_funnel_in3>; + }; + }; + }; + }; + + etm@7440000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07440000 0 0x1000>; + + cpu = <&CPU4>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm4_out: endpoint { + remote-endpoint = <&apss_funnel_in4>; + }; + }; + }; + }; + + etm@7540000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07540000 0 0x1000>; + + cpu = <&CPU5>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm5_out: endpoint { + remote-endpoint = <&apss_funnel_in5>; + }; + }; + }; + }; + + etm@7640000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07640000 0 0x1000>; + + cpu = <&CPU6>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm6_out: endpoint { + remote-endpoint = <&apss_funnel_in6>; + }; + }; + }; + }; + + etm@7740000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07740000 0 0x1000>; + + cpu = <&CPU7>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm7_out: endpoint { + remote-endpoint = <&apss_funnel_in7>; + }; + }; + }; + }; + + funnel@7800000 { /* APSS Funnel */ + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x07800000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + apss_funnel_out: endpoint { + remote-endpoint = <&apss_merge_funnel_in>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + apss_funnel_in0: endpoint { + remote-endpoint = <&etm0_out>; + }; + }; + + port@1 { + reg = <1>; + apss_funnel_in1: endpoint { + remote-endpoint = <&etm1_out>; + }; + }; + + port@2 { + reg = <2>; + apss_funnel_in2: endpoint { + remote-endpoint = <&etm2_out>; + }; + }; + + port@3 { + reg = <3>; + apss_funnel_in3: endpoint { + remote-endpoint = <&etm3_out>; + }; + }; + + port@4 { + reg = <4>; + apss_funnel_in4: endpoint { + remote-endpoint = <&etm4_out>; + }; + }; + + port@5 { + reg = <5>; + apss_funnel_in5: endpoint { + remote-endpoint = <&etm5_out>; + }; + }; + + port@6 { + reg = <6>; + apss_funnel_in6: endpoint { + remote-endpoint = <&etm6_out>; + }; + }; + + port@7 { + reg = <7>; + apss_funnel_in7: endpoint { + remote-endpoint = <&etm7_out>; + }; + }; + }; + }; + + funnel@7810000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x07810000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + apss_merge_funnel_out: endpoint { + remote-endpoint = <&funnel1_in4>; + }; + }; + }; + + in-ports { + port { + apss_merge_funnel_in: endpoint { + remote-endpoint = <&apss_funnel_out>; + }; + }; + }; + }; + + system-cache-controller@9200000 { + compatible = "qcom,sc7280-llcc"; + reg = <0 0x09200000 0 0xd0000>, <0 0x09600000 0 0x50000>; + reg-names = "llcc_base", "llcc_broadcast_base"; + interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>; + }; + + pdc: interrupt-controller@b220000 { + compatible = "qcom,sc7280-pdc", "qcom,pdc"; + reg = <0 0x0b220000 0 0x30000>; + qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, + <55 306 4>, <59 312 3>, <62 374 2>, + <64 434 2>, <66 438 3>, <69 86 1>, + <70 520 54>, <124 609 31>, <155 63 1>, + <156 716 12>; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + interrupt-controller; + }; + + aoss_qmp: power-controller@c300000 { + compatible = "qcom,sc7280-aoss-qmp"; + reg = <0 0x0c300000 0 0x100000>; + interrupts-extended = <&ipcc IPCC_CLIENT_AOP + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_AOP + IPCC_MPROC_SIGNAL_GLINK_QMP>; + + #clock-cells = <0>; + #power-domain-cells = <1>; + }; + + spmi_bus: spmi@c440000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0 0x0c440000 0 0x1100>, + <0 0x0c600000 0 0x2000000>, + <0 0x0e600000 0 0x100000>, + <0 0x0e700000 0 0xa0000>, + <0 0x0c40a000 0 0x26000>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <1>; + #size-cells = <1>; + interrupt-controller; + #interrupt-cells = <4>; + }; + + tlmm: pinctrl@f100000 { + compatible = "qcom,sc7280-pinctrl"; + reg = <0 0x0f100000 0 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 175>; + wakeup-parent = <&pdc>; + + qspi_clk: qspi-clk { + pins = "gpio14"; + function = "qspi_clk"; + }; + + qspi_cs0: qspi-cs0 { + pins = "gpio15"; + function = "qspi_cs"; + }; + + qspi_cs1: qspi-cs1 { + pins = "gpio19"; + function = "qspi_cs"; + }; + + qspi_data01: qspi-data01 { + pins = "gpio12", "gpio13"; + function = "qspi_data"; + }; + + qspi_data12: qspi-data12 { + pins = "gpio16", "gpio17"; + function = "qspi_data"; + }; + + qup_i2c0_data_clk:qup-i2c0-data-clk { + pins = "gpio0", "gpio1"; + function = "qup00"; + }; + + qup_i2c1_data_clk:qup-i2c1-data-clk { + pins = "gpio4", "gpio5"; + function = "qup01"; + }; + + qup_i2c2_data_clk:qup-i2c2-data-clk { + pins = "gpio8", "gpio9"; + function = "qup02"; + }; + + qup_i2c3_data_clk:qup-i2c3-data-clk { + pins = "gpio12", "gpio13"; + function = "qup03"; + }; + + qup_i2c4_data_clk:qup-i2c4-data-clk { + pins = "gpio16", "gpio17"; + function = "qup04"; + }; + + qup_i2c5_data_clk:qup-i2c5-data-clk { + pins = "gpio20", "gpio21"; + function = "qup05"; + }; + + qup_i2c6_data_clk:qup-i2c6-data-clk { + pins = "gpio24", "gpio25"; + function = "qup06"; + }; + + qup_i2c7_data_clk:qup-i2c7-data-clk { + pins = "gpio28", "gpio29"; + function = "qup07"; + }; + + qup_i2c8_data_clk:qup-i2c8-data-clk { + pins = "gpio32", "gpio33"; + function = "qup08"; + }; + + qup_i2c9_data_clk:qup-i2c9-data-clk { + pins = "gpio36", "gpio37"; + function = "qup09"; + }; + + qup_i2c10_data_clk:qup-i2c10-data-clk { + pins = "gpio40", "gpio41"; + function = "qup10"; + }; + + qup_i2c11_data_clk:qup-i2c11-data-clk { + pins = "gpio44", "gpio45"; + function = "qup11"; + }; + + qup_i2c12_data_clk:qup-i2c12-data-clk { + pins = "gpio48", "gpio49"; + function = "qup12"; + }; + + qup_i2c13_data_clk:qup-i2c13-data-clk { + pins = "gpio52", "gpio53"; + function = "qup13"; + }; + + qup_i2c14_data_clk:qup-i2c14-data-clk { + pins = "gpio56", "gpio57"; + function = "qup14"; + }; + + qup_i2c15_data_clk:qup-i2c15-data-clk { + pins = "gpio60", "gpio61"; + function = "qup15"; + }; + + qup_spi0_data_clk: qup-spi0-data-clk { + pins = "gpio0", "gpio1", "gpio2"; + function = "qup00"; + }; + + qup_spi0_cs: qup-spi0-cs { + pins = "gpio3"; + function = "qup00"; + }; + + qup_spi0_cs_gpio: qup-spi0-cs_gpio { + pins = "gpio3"; + function = "gpio"; + }; + + qup_spi1_data_clk: qup-spi1-data-clk { + pins = "gpio4", "gpio5", "gpio6"; + function = "qup01"; + }; + + qup_spi1_cs: qup-spi1-cs { + pins = "gpio7"; + function = "qup01"; + }; + + qup_spi1_cs_gpio: qup-spi1-cs_gpio { + pins = "gpio7"; + function = "gpio"; + }; + + qup_spi2_data_clk: qup-spi2-data-clk { + pins = "gpio8", "gpio9", "gpio10"; + function = "qup02"; + }; + + qup_spi2_cs: qup-spi2-cs { + pins = "gpio11"; + function = "qup02"; + }; + + qup_spi2_cs_gpio: qup-spi2-cs_gpio { + pins = "gpio11"; + function = "gpio"; + }; + + qup_spi3_data_clk: qup-spi3-data-clk { + pins = "gpio12", "gpio13", "gpio14"; + function = "qup03"; + }; + + qup_spi3_cs: qup-spi3-cs { + pins = "gpio15"; + function = "qup03"; + }; + + qup_spi3_cs_gpio: qup-spi3-cs_gpio { + pins = "gpio15"; + function = "gpio"; + }; + + qup_spi4_data_clk: qup-spi4-data-clk { + pins = "gpio16", "gpio17", "gpio18"; + function = "qup04"; + }; + + qup_spi4_cs: qup-spi4-cs { + pins = "gpio19"; + function = "qup04"; + }; + + qup_spi4_cs_gpio: qup-spi4-cs_gpio { + pins = "gpio19"; + function = "gpio"; + }; + + qup_spi5_data_clk: qup-spi5-data-clk { + pins = "gpio20", "gpio21", "gpio22"; + function = "qup05"; + }; + + qup_spi5_cs: qup-spi5-cs { + pins = "gpio23"; + function = "qup05"; + }; + + qup_spi5_cs_gpio: qup-spi5-cs_gpio { + pins = "gpio23"; + function = "gpio"; + }; + + qup_spi6_data_clk: qup-spi6-data-clk { + pins = "gpio24", "gpio25", "gpio26"; + function = "qup06"; + }; + + qup_spi6_cs: qup-spi6-cs { + pins = "gpio27"; + function = "qup06"; + }; + + qup_spi6_cs_gpio: qup-spi6-cs_gpio { + pins = "gpio27"; + function = "gpio"; + }; + + qup_spi7_data_clk: qup-spi7-data-clk { + pins = "gpio28", "gpio29", "gpio30"; + function = "qup07"; + }; + + qup_spi7_cs: qup-spi7-cs { + pins = "gpio31"; + function = "qup07"; + }; + + qup_spi7_cs_gpio: qup-spi7-cs_gpio { + pins = "gpio31"; + function = "gpio"; + }; + + qup_spi8_data_clk: qup-spi8-data-clk { + pins = "gpio32", "gpio33", "gpio34"; + function = "qup08"; + }; + + qup_spi8_cs: qup-spi8-cs { + pins = "gpio35"; + function = "qup08"; + }; + + qup_spi8_cs_gpio: qup-spi8-cs_gpio { + pins = "gpio35"; + function = "gpio"; + }; + + qup_spi9_data_clk: qup-spi9-data-clk { + pins = "gpio36", "gpio37", "gpio38"; + function = "qup09"; + }; + + qup_spi9_cs: qup-spi9-cs { + pins = "gpio39"; + function = "qup09"; + }; + + qup_spi9_cs_gpio: qup-spi9-cs_gpio { + pins = "gpio39"; + function = "gpio"; + }; + + qup_spi10_data_clk: qup-spi10-data-clk { + pins = "gpio40", "gpio41", "gpio42"; + function = "qup10"; + }; + + qup_spi10_cs: qup-spi10-cs { + pins = "gpio43"; + function = "qup10"; + }; + + qup_spi10_cs_gpio: qup-spi10-cs_gpio { + pins = "gpio43"; + function = "gpio"; + }; + + qup_spi11_data_clk: qup-spi11-data-clk { + pins = "gpio44", "gpio45", "gpio46"; + function = "qup11"; + }; + + qup_spi11_cs: qup-spi11-cs { + pins = "gpio47"; + function = "qup11"; + }; + + qup_spi11_cs_gpio: qup-spi11-cs_gpio { + pins = "gpio47"; + function = "gpio"; + }; + + qup_spi12_data_clk: qup-spi12-data-clk { + pins = "gpio48", "gpio49", "gpio50"; + function = "qup12"; + }; + + qup_spi12_cs: qup-spi12-cs { + pins = "gpio51"; + function = "qup12"; + }; + + qup_spi12_cs_gpio: qup-spi12-cs_gpio { + pins = "gpio51"; + function = "gpio"; + }; + + qup_spi13_data_clk: qup-spi13-data-clk { + pins = "gpio52", "gpio53", "gpio54"; + function = "qup13"; + }; + + qup_spi13_cs: qup-spi13-cs { + pins = "gpio55"; + function = "qup13"; + }; + + qup_spi13_cs_gpio: qup-spi13-cs_gpio { + pins = "gpio55"; + function = "gpio"; + }; + + qup_spi14_data_clk: qup-spi14-data-clk { + pins = "gpio56", "gpio57", "gpio58"; + function = "qup14"; + }; + + qup_spi14_cs: qup-spi14-cs { + pins = "gpio59"; + function = "qup14"; + }; + + qup_spi14_cs_gpio: qup-spi14-cs_gpio { + pins = "gpio59"; + function = "gpio"; + }; + + qup_spi15_data_clk: qup-spi15-data-clk { + pins = "gpio60", "gpio61", "gpio62"; + function = "qup15"; + }; + + qup_spi15_cs: qup-spi15-cs { + pins = "gpio63"; + function = "qup15"; + }; + + qup_spi15_cs_gpio: qup-spi15-cs_gpio { + pins = "gpio63"; + function = "gpio"; + }; + + qup_uart0_cts: qup-uart0-cts { + pins = "gpio0"; + function = "qup00"; + }; + + qup_uart0_rts: qup-uart0-rts { + pins = "gpio1"; + function = "qup00"; + }; + + qup_uart0_tx: qup-uart0-tx { + pins = "gpio2"; + function = "qup00"; + }; + + qup_uart0_rx: qup-uart0-rx { + pins = "gpio3"; + function = "qup00"; + }; + + qup_uart1_cts: qup-uart1-cts { + pins = "gpio4"; + function = "qup01"; + }; + + qup_uart1_rts: qup-uart1-rts { + pins = "gpio5"; + function = "qup01"; + }; + + qup_uart1_tx: qup-uart1-tx { + pins = "gpio6"; + function = "qup01"; + }; + + qup_uart1_rx: qup-uart1-rx { + pins = "gpio7"; + function = "qup01"; + }; + + qup_uart2_cts: qup-uart2-cts { + pins = "gpio8"; + function = "qup02"; + }; + + qup_uart2_rts: qup-uart2-rts { + pins = "gpio9"; + function = "qup02"; + }; + + qup_uart2_tx: qup-uart2-tx { + pins = "gpio10"; + function = "qup02"; + }; + + qup_uart2_rx: qup-uart2-rx { + pins = "gpio11"; + function = "qup02"; + }; + + qup_uart3_cts: qup-uart3-cts { + pins = "gpio12"; + function = "qup03"; + }; + + qup_uart3_rts: qup-uart3-rts { + pins = "gpio13"; + function = "qup03"; + }; + + qup_uart3_tx: qup-uart3-tx { + pins = "gpio14"; + function = "qup03"; + }; + + qup_uart3_rx: qup-uart3-rx { + pins = "gpio15"; + function = "qup03"; + }; + + qup_uart4_cts: qup-uart4-cts { + pins = "gpio16"; + function = "qup04"; + }; + + qup_uart4_rts: qup-uart4-rts { + pins = "gpio17"; + function = "qup04"; + }; + + qup_uart4_tx: qup-uart4-tx { + pins = "gpio18"; + function = "qup04"; + }; + + qup_uart4_rx: qup-uart4-rx { + pins = "gpio19"; + function = "qup04"; + }; + + qup_uart5_cts: qup-uart5-cts { + pins = "gpio20"; + function = "qup05"; + }; + + qup_uart5_rts: qup-uart5-rts { + pins = "gpio21"; + function = "qup05"; + }; + + qup_uart5_tx: qup-uart5-tx { + pins = "gpio22"; + function = "qup05"; + }; + + qup_uart5_rx: qup-uart5-rx { + pins = "gpio23"; + function = "qup05"; + }; - etm@7340000 { - compatible = "arm,coresight-etm4x", "arm,primecell"; - reg = <0 0x07340000 0 0x1000>; + qup_uart6_cts: qup-uart6-cts { + pins = "gpio24"; + function = "qup06"; + }; - cpu = <&CPU3>; + qup_uart6_rts: qup-uart6-rts { + pins = "gpio25"; + function = "qup06"; + }; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; - arm,coresight-loses-context-with-cpu; - qcom,skip-power-up; + qup_uart6_tx: qup-uart6-tx { + pins = "gpio26"; + function = "qup06"; + }; - out-ports { - port { - etm3_out: endpoint { - remote-endpoint = <&apss_funnel_in3>; - }; - }; + qup_uart6_rx: qup-uart6-rx { + pins = "gpio27"; + function = "qup06"; }; - }; - etm@7440000 { - compatible = "arm,coresight-etm4x", "arm,primecell"; - reg = <0 0x07440000 0 0x1000>; + qup_uart7_cts: qup-uart7-cts { + pins = "gpio28"; + function = "qup07"; + }; - cpu = <&CPU4>; + qup_uart7_rts: qup-uart7-rts { + pins = "gpio29"; + function = "qup07"; + }; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; - arm,coresight-loses-context-with-cpu; - qcom,skip-power-up; + qup_uart7_tx: qup-uart7-tx { + pins = "gpio30"; + function = "qup07"; + }; - out-ports { - port { - etm4_out: endpoint { - remote-endpoint = <&apss_funnel_in4>; - }; - }; + qup_uart7_rx: qup-uart7-rx { + pins = "gpio31"; + function = "qup07"; }; - }; - etm@7540000 { - compatible = "arm,coresight-etm4x", "arm,primecell"; - reg = <0 0x07540000 0 0x1000>; + qup_uart8_cts: qup-uart8-cts { + pins = "gpio32"; + function = "qup08"; + }; - cpu = <&CPU5>; + qup_uart8_rts: qup-uart8-rts { + pins = "gpio33"; + function = "qup08"; + }; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; - arm,coresight-loses-context-with-cpu; - qcom,skip-power-up; + qup_uart8_tx: qup-uart8-tx { + pins = "gpio34"; + function = "qup08"; + }; - out-ports { - port { - etm5_out: endpoint { - remote-endpoint = <&apss_funnel_in5>; - }; - }; + qup_uart8_rx: qup-uart8-rx { + pins = "gpio35"; + function = "qup08"; }; - }; - etm@7640000 { - compatible = "arm,coresight-etm4x", "arm,primecell"; - reg = <0 0x07640000 0 0x1000>; + qup_uart9_cts: qup-uart9-cts { + pins = "gpio36"; + function = "qup09"; + }; - cpu = <&CPU6>; + qup_uart9_rts: qup-uart9-rts { + pins = "gpio37"; + function = "qup09"; + }; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; - arm,coresight-loses-context-with-cpu; - qcom,skip-power-up; + qup_uart9_tx: qup-uart9-tx { + pins = "gpio38"; + function = "qup09"; + }; - out-ports { - port { - etm6_out: endpoint { - remote-endpoint = <&apss_funnel_in6>; - }; - }; + qup_uart9_rx: qup-uart9-rx { + pins = "gpio39"; + function = "qup09"; }; - }; - etm@7740000 { - compatible = "arm,coresight-etm4x", "arm,primecell"; - reg = <0 0x07740000 0 0x1000>; + qup_uart10_cts: qup-uart10-cts { + pins = "gpio40"; + function = "qup10"; + }; - cpu = <&CPU7>; + qup_uart10_rts: qup-uart10-rts { + pins = "gpio41"; + function = "qup10"; + }; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; - arm,coresight-loses-context-with-cpu; - qcom,skip-power-up; + qup_uart10_tx: qup-uart10-tx { + pins = "gpio42"; + function = "qup10"; + }; - out-ports { - port { - etm7_out: endpoint { - remote-endpoint = <&apss_funnel_in7>; - }; - }; + qup_uart10_rx: qup-uart10-rx { + pins = "gpio43"; + function = "qup10"; }; - }; - funnel@7800000 { /* APSS Funnel */ - compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; - reg = <0 0x07800000 0 0x1000>; + qup_uart11_cts: qup-uart11-cts { + pins = "gpio44"; + function = "qup11"; + }; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; + qup_uart11_rts: qup-uart11-rts { + pins = "gpio45"; + function = "qup11"; + }; - out-ports { - port { - apss_funnel_out: endpoint { - remote-endpoint = <&apss_merge_funnel_in>; - }; - }; + qup_uart11_tx: qup-uart11-tx { + pins = "gpio46"; + function = "qup11"; }; - in-ports { - #address-cells = <1>; - #size-cells = <0>; + qup_uart11_rx: qup-uart11-rx { + pins = "gpio47"; + function = "qup11"; + }; - port@0 { - reg = <0>; - apss_funnel_in0: endpoint { - remote-endpoint = <&etm0_out>; - }; - }; + qup_uart12_cts: qup-uart12-cts { + pins = "gpio48"; + function = "qup12"; + }; - port@1 { - reg = <1>; - apss_funnel_in1: endpoint { - remote-endpoint = <&etm1_out>; - }; - }; + qup_uart12_rts: qup-uart12-rts { + pins = "gpio49"; + function = "qup12"; + }; - port@2 { - reg = <2>; - apss_funnel_in2: endpoint { - remote-endpoint = <&etm2_out>; - }; - }; + qup_uart12_tx: qup-uart12-tx { + pins = "gpio50"; + function = "qup12"; + }; - port@3 { - reg = <3>; - apss_funnel_in3: endpoint { - remote-endpoint = <&etm3_out>; - }; - }; + qup_uart12_rx: qup-uart12-rx { + pins = "gpio51"; + function = "qup12"; + }; - port@4 { - reg = <4>; - apss_funnel_in4: endpoint { - remote-endpoint = <&etm4_out>; - }; - }; + qup_uart13_cts: qup-uart13-cts { + pins = "gpio52"; + function = "qup13"; + }; - port@5 { - reg = <5>; - apss_funnel_in5: endpoint { - remote-endpoint = <&etm5_out>; - }; - }; + qup_uart13_rts: qup-uart13-rts { + pins = "gpio53"; + function = "qup13"; + }; - port@6 { - reg = <6>; - apss_funnel_in6: endpoint { - remote-endpoint = <&etm6_out>; - }; - }; + qup_uart13_tx: qup-uart13-tx { + pins = "gpio54"; + function = "qup13"; + }; - port@7 { - reg = <7>; - apss_funnel_in7: endpoint { - remote-endpoint = <&etm7_out>; - }; - }; + qup_uart13_rx: qup-uart13-rx { + pins = "gpio55"; + function = "qup13"; }; - }; - funnel@7810000 { - compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; - reg = <0 0x07810000 0 0x1000>; + qup_uart14_cts: qup-uart14-cts { + pins = "gpio56"; + function = "qup14"; + }; - clocks = <&aoss_qmp>; - clock-names = "apb_pclk"; + qup_uart14_rts: qup-uart14-rts { + pins = "gpio57"; + function = "qup14"; + }; - out-ports { - port { - apss_merge_funnel_out: endpoint { - remote-endpoint = <&funnel1_in4>; - }; - }; + qup_uart14_tx: qup-uart14-tx { + pins = "gpio58"; + function = "qup14"; }; - in-ports { - port { - apss_merge_funnel_in: endpoint { - remote-endpoint = <&apss_funnel_out>; - }; - }; + qup_uart14_rx: qup-uart14-rx { + pins = "gpio59"; + function = "qup14"; }; - }; - system-cache-controller@9200000 { - compatible = "qcom,sc7280-llcc"; - reg = <0 0x09200000 0 0xd0000>, <0 0x09600000 0 0x50000>; - reg-names = "llcc_base", "llcc_broadcast_base"; - interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>; - }; + qup_uart15_cts: qup-uart15-cts { + pins = "gpio60"; + function = "qup15"; + }; - pdc: interrupt-controller@b220000 { - compatible = "qcom,sc7280-pdc", "qcom,pdc"; - reg = <0 0x0b220000 0 0x30000>; - qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, - <55 306 4>, <59 312 3>, <62 374 2>, - <64 434 2>, <66 438 3>, <69 86 1>, - <70 520 54>, <124 609 31>, <155 63 1>, - <156 716 12>; - #interrupt-cells = <2>; - interrupt-parent = <&intc>; - interrupt-controller; - }; + qup_uart15_rts: qup-uart15-rts { + pins = "gpio61"; + function = "qup15"; + }; - aoss_qmp: power-controller@c300000 { - compatible = "qcom,sc7280-aoss-qmp"; - reg = <0 0x0c300000 0 0x100000>; - interrupts-extended = <&ipcc IPCC_CLIENT_AOP - IPCC_MPROC_SIGNAL_GLINK_QMP - IRQ_TYPE_EDGE_RISING>; - mboxes = <&ipcc IPCC_CLIENT_AOP - IPCC_MPROC_SIGNAL_GLINK_QMP>; + qup_uart15_tx: qup-uart15-tx { + pins = "gpio62"; + function = "qup15"; + }; - #clock-cells = <0>; - #power-domain-cells = <1>; - }; + qup_uart15_rx: qup-uart15-rx { + pins = "gpio63"; + function = "qup15"; + }; - spmi_bus: spmi@c440000 { - compatible = "qcom,spmi-pmic-arb"; - reg = <0 0x0c440000 0 0x1100>, - <0 0x0c600000 0 0x2000000>, - <0 0x0e600000 0 0x100000>, - <0 0x0e700000 0 0xa0000>, - <0 0x0c40a000 0 0x26000>; - reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; - interrupt-names = "periph_irq"; - interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>; - qcom,ee = <0>; - qcom,channel = <0>; - #address-cells = <1>; - #size-cells = <1>; - interrupt-controller; - #interrupt-cells = <4>; }; - tlmm: pinctrl@f100000 { - compatible = "qcom,sc7280-pinctrl"; - reg = <0 0x0f100000 0 0x300000>; - interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - gpio-ranges = <&tlmm 0 0 175>; - wakeup-parent = <&pdc>; + qspi_opp_table: qspi-opp-table { + compatible = "operating-points-v2"; - qup_uart5_default: qup-uart5-default { - pins = "gpio46", "gpio47"; - function = "qup13"; + opp-75000000 { + opp-hz = /bits/ 64 <75000000>; + required-opps = <&rpmhpd_opp_low_svs>; }; + + opp-150000000 { + opp-hz = /bits/ 64 <150000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + + qspi: spi@88dc000 { + compatible = "qcom,qspi-v1"; + reg = <0 0x088dc000 0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>, + <&gcc GCC_QSPI_CORE_CLK>; + clock-names = "iface", "core"; + interconnects = <&gem_noc MASTER_APPSS_PROC 0 + &cnoc2 SLAVE_QSPI_0 0>; + interconnect-names = "qspi-config"; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&qspi_opp_table>; + status = "disabled"; }; apps_smmu: iommu@15000000 {

[V2] arm64: dts: sc7280: Add qspi, qupv3_0 and qupv3_1 nodes

Commit Message

Comments

Patch