| Message ID | 20210506191829.8271-6-p.yadav@ti.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Avoid odd length/address read/writes in 8D-8D-8D mode. | expand |
Am 2021-05-06 21:18, schrieb Pratyush Yadav: > On Octal DTR capable flashes like Micron Xcella reads cannot start or > end at an odd address in Octal DTR mode. Extra bytes need to be read at > the start or end to make sure both the start address and length remain > even. > > To avoid allocating too much extra memory, thereby putting unnecessary > memory pressure on the system, the temporary buffer containing the > extra > padding bytes is capped at PAGE_SIZE bytes. The rest of the 2-byte > aligned part should be read directly in the main buffer. > > Signed-off-by: Pratyush Yadav <p.yadav@ti.com> > --- > > drivers/mtd/spi-nor/core.c | 81 +++++++++++++++++++++++++++++++++++++- > 1 file changed, 80 insertions(+), 1 deletion(-) > > diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c > index 5cc206b8bbf3..3d66cc34af4d 100644 > --- a/drivers/mtd/spi-nor/core.c > +++ b/drivers/mtd/spi-nor/core.c > @@ -1904,6 +1904,82 @@ static const struct flash_info > *spi_nor_read_id(struct spi_nor *nor) > return ERR_PTR(-ENODEV); > } > > +/* > + * On Octal DTR capable flashes like Micron Xcella reads cannot start > or > + * end at an odd address in Octal DTR mode. Extra bytes need to be > read > + * at the start or end to make sure both the start address and length > + * remain even. > + */ > +static int spi_nor_octal_dtr_read(struct spi_nor *nor, loff_t from, > size_t len, > + u_char *buf) > +{ > + u_char *tmp_buf; > + size_t tmp_len; > + loff_t start, end; > + int ret, bytes_read; > + > + if (IS_ALIGNED(from, 2) && IS_ALIGNED(len, 2)) > + return spi_nor_read_data(nor, from, len, buf); > + else if (IS_ALIGNED(from, 2) && len > PAGE_SIZE) > + return spi_nor_read_data(nor, from, round_down(len, PAGE_SIZE), > + buf); > + > + tmp_buf = kmalloc(PAGE_SIZE, GFP_KERNEL); > + if (!tmp_buf) > + return -ENOMEM; > + > + start = round_down(from, 2); > + end = round_up(from + len, 2); > + > + /* > + * Avoid allocating too much memory. The requested read length might > be > + * quite large. Allocating a buffer just as large (slightly bigger, > in > + * fact) would put unnecessary memory pressure on the system. > + * > + * For example if the read is from 3 to 1M, then this will read from > 2 > + * to 4098. The reads from 4098 to 1M will then not need a temporary > + * buffer so they can proceed as normal. > + */ > + tmp_len = min_t(size_t, end - start, PAGE_SIZE); > + > + ret = spi_nor_read_data(nor, start, tmp_len, tmp_buf); > + if (ret == 0) { > + ret = -EIO; > + goto out; > + } > + if (ret < 0) > + goto out; > + > + /* > + * More bytes are read than actually requested, but that number can't > be > + * reported to the calling function or it will confuse its > calculations. > + * Calculate how many of the _requested_ bytes were read. > + */ > + bytes_read = ret; > + > + if (from != start) > + ret -= from - start; > + > + /* > + * Only account for extra bytes at the end if they were actually > read. > + * For example, if the total length was truncated because of > temporary > + * buffer size limit then the adjustment for the extra bytes at the > end > + * is not needed. > + */ > + if (start + bytes_read == end) > + ret -= end - (from + len); > + > + if (ret < 0) { > + ret = -EIO; > + goto out; > + } > + > + memcpy(buf, tmp_buf + (from - start), ret); > +out: > + kfree(tmp_buf); > + return ret; > +} > + > static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len, > size_t *retlen, u_char *buf) > { > @@ -1921,7 +1997,10 @@ static int spi_nor_read(struct mtd_info *mtd, > loff_t from, size_t len, > > addr = spi_nor_convert_addr(nor, addr); > > - ret = spi_nor_read_data(nor, addr, len, buf); > + if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) > + ret = spi_nor_octal_dtr_read(nor, addr, len, buf); > + else > + ret = spi_nor_read_data(nor, addr, len, buf); > if (ret == 0) { > /* We shouldn't see 0-length reads */ > ret = -EIO; Reviewed-by: Michael Walle <michael@walle.cc> I wonder how much performance is lost if this would just split one transfer into up to three ones: 2 byte, size - 2, 2 bytes. -michael
On 07/05/21 05:51PM, Michael Walle wrote: > Am 2021-05-06 21:18, schrieb Pratyush Yadav: > > On Octal DTR capable flashes like Micron Xcella reads cannot start or > > end at an odd address in Octal DTR mode. Extra bytes need to be read at > > the start or end to make sure both the start address and length remain > > even. > > > > To avoid allocating too much extra memory, thereby putting unnecessary > > memory pressure on the system, the temporary buffer containing the extra > > padding bytes is capped at PAGE_SIZE bytes. The rest of the 2-byte > > aligned part should be read directly in the main buffer. > > > > Signed-off-by: Pratyush Yadav <p.yadav@ti.com> > > --- > > > > drivers/mtd/spi-nor/core.c | 81 +++++++++++++++++++++++++++++++++++++- > > 1 file changed, 80 insertions(+), 1 deletion(-) > > > > diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c > > index 5cc206b8bbf3..3d66cc34af4d 100644 > > --- a/drivers/mtd/spi-nor/core.c > > +++ b/drivers/mtd/spi-nor/core.c > > @@ -1904,6 +1904,82 @@ static const struct flash_info > > *spi_nor_read_id(struct spi_nor *nor) > > return ERR_PTR(-ENODEV); > > } > > > > +/* > > + * On Octal DTR capable flashes like Micron Xcella reads cannot start > > or > > + * end at an odd address in Octal DTR mode. Extra bytes need to be read > > + * at the start or end to make sure both the start address and length > > + * remain even. > > + */ > > +static int spi_nor_octal_dtr_read(struct spi_nor *nor, loff_t from, > > size_t len, > > + u_char *buf) > > +{ > > + u_char *tmp_buf; > > + size_t tmp_len; > > + loff_t start, end; > > + int ret, bytes_read; > > + > > + if (IS_ALIGNED(from, 2) && IS_ALIGNED(len, 2)) > > + return spi_nor_read_data(nor, from, len, buf); > > + else if (IS_ALIGNED(from, 2) && len > PAGE_SIZE) > > + return spi_nor_read_data(nor, from, round_down(len, PAGE_SIZE), > > + buf); > > + > > + tmp_buf = kmalloc(PAGE_SIZE, GFP_KERNEL); > > + if (!tmp_buf) > > + return -ENOMEM; > > + > > + start = round_down(from, 2); > > + end = round_up(from + len, 2); > > + > > + /* > > + * Avoid allocating too much memory. The requested read length might > > be > > + * quite large. Allocating a buffer just as large (slightly bigger, in > > + * fact) would put unnecessary memory pressure on the system. > > + * > > + * For example if the read is from 3 to 1M, then this will read from 2 > > + * to 4098. The reads from 4098 to 1M will then not need a temporary > > + * buffer so they can proceed as normal. > > + */ > > + tmp_len = min_t(size_t, end - start, PAGE_SIZE); > > + > > + ret = spi_nor_read_data(nor, start, tmp_len, tmp_buf); > > + if (ret == 0) { > > + ret = -EIO; > > + goto out; > > + } > > + if (ret < 0) > > + goto out; > > + > > + /* > > + * More bytes are read than actually requested, but that number can't > > be > > + * reported to the calling function or it will confuse its > > calculations. > > + * Calculate how many of the _requested_ bytes were read. > > + */ > > + bytes_read = ret; > > + > > + if (from != start) > > + ret -= from - start; > > + > > + /* > > + * Only account for extra bytes at the end if they were actually read. > > + * For example, if the total length was truncated because of temporary > > + * buffer size limit then the adjustment for the extra bytes at the > > end > > + * is not needed. > > + */ > > + if (start + bytes_read == end) > > + ret -= end - (from + len); > > + > > + if (ret < 0) { > > + ret = -EIO; > > + goto out; > > + } > > + > > + memcpy(buf, tmp_buf + (from - start), ret); > > +out: > > + kfree(tmp_buf); > > + return ret; > > +} > > + > > static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len, > > size_t *retlen, u_char *buf) > > { > > @@ -1921,7 +1997,10 @@ static int spi_nor_read(struct mtd_info *mtd, > > loff_t from, size_t len, > > > > addr = spi_nor_convert_addr(nor, addr); > > > > - ret = spi_nor_read_data(nor, addr, len, buf); > > + if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) > > + ret = spi_nor_octal_dtr_read(nor, addr, len, buf); > > + else > > + ret = spi_nor_read_data(nor, addr, len, buf); > > if (ret == 0) { > > /* We shouldn't see 0-length reads */ > > ret = -EIO; > > Reviewed-by: Michael Walle <michael@walle.cc> Thanks. > > I wonder how much performance is lost if this would just split > one transfer into up to three ones: 2 byte, size - 2, 2 bytes. This case is not really possible since it would try to read PAGE_SIZE whenever it can. But there is a situation possible where one transfer is split into three. It would look something like: 4096 bytes, size - 4096 bytes, 2 bytes. I am trying to find a balance between minimizing number of reads while keeping the size of the temporary buffer to a reasonable limit. This is the best I could come up with. It optimizes for smaller transfers so while the absolute amount of overhead remains roughly the same, the ratio of it relative to read size is smaller. You can optimize for read performance if you are willing to waste memory by simple allocating a size + 2 bytes long buffer. Then the read can proceed in one transaction. But IMO memory is much more important compared to read throughput.
Am 2021-05-07 20:04, schrieb Pratyush Yadav: > On 07/05/21 05:51PM, Michael Walle wrote: >> Am 2021-05-06 21:18, schrieb Pratyush Yadav: >> > On Octal DTR capable flashes like Micron Xcella reads cannot start or >> > end at an odd address in Octal DTR mode. Extra bytes need to be read at >> > the start or end to make sure both the start address and length remain >> > even. >> > >> > To avoid allocating too much extra memory, thereby putting unnecessary >> > memory pressure on the system, the temporary buffer containing the extra >> > padding bytes is capped at PAGE_SIZE bytes. The rest of the 2-byte >> > aligned part should be read directly in the main buffer. >> > >> > Signed-off-by: Pratyush Yadav <p.yadav@ti.com> >> > --- >> > >> > drivers/mtd/spi-nor/core.c | 81 +++++++++++++++++++++++++++++++++++++- >> > 1 file changed, 80 insertions(+), 1 deletion(-) >> > >> > diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c >> > index 5cc206b8bbf3..3d66cc34af4d 100644 >> > --- a/drivers/mtd/spi-nor/core.c >> > +++ b/drivers/mtd/spi-nor/core.c >> > @@ -1904,6 +1904,82 @@ static const struct flash_info >> > *spi_nor_read_id(struct spi_nor *nor) >> > return ERR_PTR(-ENODEV); >> > } >> > >> > +/* >> > + * On Octal DTR capable flashes like Micron Xcella reads cannot start >> > or >> > + * end at an odd address in Octal DTR mode. Extra bytes need to be read >> > + * at the start or end to make sure both the start address and length >> > + * remain even. >> > + */ >> > +static int spi_nor_octal_dtr_read(struct spi_nor *nor, loff_t from, >> > size_t len, >> > + u_char *buf) >> > +{ >> > + u_char *tmp_buf; >> > + size_t tmp_len; >> > + loff_t start, end; >> > + int ret, bytes_read; >> > + >> > + if (IS_ALIGNED(from, 2) && IS_ALIGNED(len, 2)) >> > + return spi_nor_read_data(nor, from, len, buf); >> > + else if (IS_ALIGNED(from, 2) && len > PAGE_SIZE) >> > + return spi_nor_read_data(nor, from, round_down(len, PAGE_SIZE), >> > + buf); >> > + >> > + tmp_buf = kmalloc(PAGE_SIZE, GFP_KERNEL); >> > + if (!tmp_buf) >> > + return -ENOMEM; >> > + >> > + start = round_down(from, 2); >> > + end = round_up(from + len, 2); >> > + >> > + /* >> > + * Avoid allocating too much memory. The requested read length might >> > be >> > + * quite large. Allocating a buffer just as large (slightly bigger, in >> > + * fact) would put unnecessary memory pressure on the system. >> > + * >> > + * For example if the read is from 3 to 1M, then this will read from 2 >> > + * to 4098. The reads from 4098 to 1M will then not need a temporary >> > + * buffer so they can proceed as normal. >> > + */ >> > + tmp_len = min_t(size_t, end - start, PAGE_SIZE); >> > + >> > + ret = spi_nor_read_data(nor, start, tmp_len, tmp_buf); >> > + if (ret == 0) { >> > + ret = -EIO; >> > + goto out; >> > + } >> > + if (ret < 0) >> > + goto out; >> > + >> > + /* >> > + * More bytes are read than actually requested, but that number can't >> > be >> > + * reported to the calling function or it will confuse its >> > calculations. >> > + * Calculate how many of the _requested_ bytes were read. >> > + */ >> > + bytes_read = ret; >> > + >> > + if (from != start) >> > + ret -= from - start; >> > + >> > + /* >> > + * Only account for extra bytes at the end if they were actually read. >> > + * For example, if the total length was truncated because of temporary >> > + * buffer size limit then the adjustment for the extra bytes at the >> > end >> > + * is not needed. >> > + */ >> > + if (start + bytes_read == end) >> > + ret -= end - (from + len); >> > + >> > + if (ret < 0) { >> > + ret = -EIO; >> > + goto out; >> > + } >> > + >> > + memcpy(buf, tmp_buf + (from - start), ret); >> > +out: >> > + kfree(tmp_buf); >> > + return ret; >> > +} >> > + >> > static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len, >> > size_t *retlen, u_char *buf) >> > { >> > @@ -1921,7 +1997,10 @@ static int spi_nor_read(struct mtd_info *mtd, >> > loff_t from, size_t len, >> > >> > addr = spi_nor_convert_addr(nor, addr); >> > >> > - ret = spi_nor_read_data(nor, addr, len, buf); >> > + if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) >> > + ret = spi_nor_octal_dtr_read(nor, addr, len, buf); >> > + else >> > + ret = spi_nor_read_data(nor, addr, len, buf); >> > if (ret == 0) { >> > /* We shouldn't see 0-length reads */ >> > ret = -EIO; >> >> Reviewed-by: Michael Walle <michael@walle.cc> > > Thanks. > >> >> I wonder how much performance is lost if this would just split >> one transfer into up to three ones: 2 byte, size - 2, 2 bytes. > > This case is not really possible since it would try to read PAGE_SIZE > whenever it can. But there is a situation possible where one transfer > is > split into three. It would look something like: 4096 bytes, size - 4096 > bytes, 2 bytes. Ah no, I wasn't talking about your implementation, but just having a naive one where you don't move around up to PAGE_SIZE of data but just read 2 bytes in the beginning (if unaligned) and 2 bytes at the end (if unaligned) and reading the part in between just as usual because its then aligend. > I am trying to find a balance between minimizing number of reads while > keeping the size of the temporary buffer to a reasonable limit. This is > the best I could come up with. It optimizes for smaller transfers so > while the absolute amount of overhead remains roughly the same, the > ratio of it relative to read size is smaller. Yes, with this you will have that memcpy() and one transfer for transfers up to PAGE_SIZE; the "naive" one above would have up to three depending on the aligment. > You can optimize for read performance if you are willing to waste > memory > by simple allocating a size + 2 bytes long buffer. Then the read can > proceed in one transaction. But IMO memory is much more important > compared to read throughput. -michael
On 07/05/21 08:14PM, Michael Walle wrote: > Am 2021-05-07 20:04, schrieb Pratyush Yadav: > > On 07/05/21 05:51PM, Michael Walle wrote: > > > Am 2021-05-06 21:18, schrieb Pratyush Yadav: > > > > On Octal DTR capable flashes like Micron Xcella reads cannot start or > > > > end at an odd address in Octal DTR mode. Extra bytes need to be read at > > > > the start or end to make sure both the start address and length remain > > > > even. > > > > > > > > To avoid allocating too much extra memory, thereby putting unnecessary > > > > memory pressure on the system, the temporary buffer containing the extra > > > > padding bytes is capped at PAGE_SIZE bytes. The rest of the 2-byte > > > > aligned part should be read directly in the main buffer. > > > > > > > > Signed-off-by: Pratyush Yadav <p.yadav@ti.com> > > > > --- > > > > > > > > drivers/mtd/spi-nor/core.c | 81 +++++++++++++++++++++++++++++++++++++- > > > > 1 file changed, 80 insertions(+), 1 deletion(-) > > > > > > > > diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c > > > > index 5cc206b8bbf3..3d66cc34af4d 100644 > > > > --- a/drivers/mtd/spi-nor/core.c > > > > +++ b/drivers/mtd/spi-nor/core.c > > > > @@ -1904,6 +1904,82 @@ static const struct flash_info > > > > *spi_nor_read_id(struct spi_nor *nor) > > > > return ERR_PTR(-ENODEV); > > > > } > > > > > > > > +/* > > > > + * On Octal DTR capable flashes like Micron Xcella reads cannot start > > > > or > > > > + * end at an odd address in Octal DTR mode. Extra bytes need to be read > > > > + * at the start or end to make sure both the start address and length > > > > + * remain even. > > > > + */ > > > > +static int spi_nor_octal_dtr_read(struct spi_nor *nor, loff_t from, > > > > size_t len, > > > > + u_char *buf) > > > > +{ > > > > + u_char *tmp_buf; > > > > + size_t tmp_len; > > > > + loff_t start, end; > > > > + int ret, bytes_read; > > > > + > > > > + if (IS_ALIGNED(from, 2) && IS_ALIGNED(len, 2)) > > > > + return spi_nor_read_data(nor, from, len, buf); > > > > + else if (IS_ALIGNED(from, 2) && len > PAGE_SIZE) > > > > + return spi_nor_read_data(nor, from, round_down(len, PAGE_SIZE), > > > > + buf); > > > > + > > > > + tmp_buf = kmalloc(PAGE_SIZE, GFP_KERNEL); > > > > + if (!tmp_buf) > > > > + return -ENOMEM; > > > > + > > > > + start = round_down(from, 2); > > > > + end = round_up(from + len, 2); > > > > + > > > > + /* > > > > + * Avoid allocating too much memory. The requested read length might > > > > be > > > > + * quite large. Allocating a buffer just as large (slightly bigger, in > > > > + * fact) would put unnecessary memory pressure on the system. > > > > + * > > > > + * For example if the read is from 3 to 1M, then this will read from 2 > > > > + * to 4098. The reads from 4098 to 1M will then not need a temporary > > > > + * buffer so they can proceed as normal. > > > > + */ > > > > + tmp_len = min_t(size_t, end - start, PAGE_SIZE); > > > > + > > > > + ret = spi_nor_read_data(nor, start, tmp_len, tmp_buf); > > > > + if (ret == 0) { > > > > + ret = -EIO; > > > > + goto out; > > > > + } > > > > + if (ret < 0) > > > > + goto out; > > > > + > > > > + /* > > > > + * More bytes are read than actually requested, but that number can't > > > > be > > > > + * reported to the calling function or it will confuse its > > > > calculations. > > > > + * Calculate how many of the _requested_ bytes were read. > > > > + */ > > > > + bytes_read = ret; > > > > + > > > > + if (from != start) > > > > + ret -= from - start; > > > > + > > > > + /* > > > > + * Only account for extra bytes at the end if they were actually read. > > > > + * For example, if the total length was truncated because of temporary > > > > + * buffer size limit then the adjustment for the extra bytes at the > > > > end > > > > + * is not needed. > > > > + */ > > > > + if (start + bytes_read == end) > > > > + ret -= end - (from + len); > > > > + > > > > + if (ret < 0) { > > > > + ret = -EIO; > > > > + goto out; > > > > + } > > > > + > > > > + memcpy(buf, tmp_buf + (from - start), ret); > > > > +out: > > > > + kfree(tmp_buf); > > > > + return ret; > > > > +} > > > > + > > > > static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len, > > > > size_t *retlen, u_char *buf) > > > > { > > > > @@ -1921,7 +1997,10 @@ static int spi_nor_read(struct mtd_info *mtd, > > > > loff_t from, size_t len, > > > > > > > > addr = spi_nor_convert_addr(nor, addr); > > > > > > > > - ret = spi_nor_read_data(nor, addr, len, buf); > > > > + if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) > > > > + ret = spi_nor_octal_dtr_read(nor, addr, len, buf); > > > > + else > > > > + ret = spi_nor_read_data(nor, addr, len, buf); > > > > if (ret == 0) { > > > > /* We shouldn't see 0-length reads */ > > > > ret = -EIO; > > > > > > Reviewed-by: Michael Walle <michael@walle.cc> > > > > Thanks. > > > > > > > > I wonder how much performance is lost if this would just split > > > one transfer into up to three ones: 2 byte, size - 2, 2 bytes. > > > > This case is not really possible since it would try to read PAGE_SIZE > > whenever it can. But there is a situation possible where one transfer is > > split into three. It would look something like: 4096 bytes, size - 4096 > > bytes, 2 bytes. > > Ah no, I wasn't talking about your implementation, but just having a naive > one where you don't move around up to PAGE_SIZE of data but just read > 2 bytes in the beginning (if unaligned) and 2 bytes at the end (if > unaligned) > and reading the part in between just as usual because its then aligend. > > > I am trying to find a balance between minimizing number of reads while > > keeping the size of the temporary buffer to a reasonable limit. This is > > the best I could come up with. It optimizes for smaller transfers so > > while the absolute amount of overhead remains roughly the same, the > > ratio of it relative to read size is smaller. > > Yes, with this you will have that memcpy() and one transfer for transfers > up to PAGE_SIZE; the "naive" one above would have up to three depending on > the aligment. Right. Smaller transfers lose much more performance to the overhead than the larger ones do. So I think the optimization is worth the extra code complexity. > > > You can optimize for read performance if you are willing to waste memory > > by simple allocating a size + 2 bytes long buffer. Then the read can > > proceed in one transaction. But IMO memory is much more important > > compared to read throughput. > > -michael
diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c index 5cc206b8bbf3..3d66cc34af4d 100644 --- a/drivers/mtd/spi-nor/core.c +++ b/drivers/mtd/spi-nor/core.c @@ -1904,6 +1904,82 @@ static const struct flash_info *spi_nor_read_id(struct spi_nor *nor) return ERR_PTR(-ENODEV); } +/* + * On Octal DTR capable flashes like Micron Xcella reads cannot start or + * end at an odd address in Octal DTR mode. Extra bytes need to be read + * at the start or end to make sure both the start address and length + * remain even. + */ +static int spi_nor_octal_dtr_read(struct spi_nor *nor, loff_t from, size_t len, + u_char *buf) +{ + u_char *tmp_buf; + size_t tmp_len; + loff_t start, end; + int ret, bytes_read; + + if (IS_ALIGNED(from, 2) && IS_ALIGNED(len, 2)) + return spi_nor_read_data(nor, from, len, buf); + else if (IS_ALIGNED(from, 2) && len > PAGE_SIZE) + return spi_nor_read_data(nor, from, round_down(len, PAGE_SIZE), + buf); + + tmp_buf = kmalloc(PAGE_SIZE, GFP_KERNEL); + if (!tmp_buf) + return -ENOMEM; + + start = round_down(from, 2); + end = round_up(from + len, 2); + + /* + * Avoid allocating too much memory. The requested read length might be + * quite large. Allocating a buffer just as large (slightly bigger, in + * fact) would put unnecessary memory pressure on the system. + * + * For example if the read is from 3 to 1M, then this will read from 2 + * to 4098. The reads from 4098 to 1M will then not need a temporary + * buffer so they can proceed as normal. + */ + tmp_len = min_t(size_t, end - start, PAGE_SIZE); + + ret = spi_nor_read_data(nor, start, tmp_len, tmp_buf); + if (ret == 0) { + ret = -EIO; + goto out; + } + if (ret < 0) + goto out; + + /* + * More bytes are read than actually requested, but that number can't be + * reported to the calling function or it will confuse its calculations. + * Calculate how many of the _requested_ bytes were read. + */ + bytes_read = ret; + + if (from != start) + ret -= from - start; + + /* + * Only account for extra bytes at the end if they were actually read. + * For example, if the total length was truncated because of temporary + * buffer size limit then the adjustment for the extra bytes at the end + * is not needed. + */ + if (start + bytes_read == end) + ret -= end - (from + len); + + if (ret < 0) { + ret = -EIO; + goto out; + } + + memcpy(buf, tmp_buf + (from - start), ret); +out: + kfree(tmp_buf); + return ret; +} + static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf) { @@ -1921,7 +1997,10 @@ static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len, addr = spi_nor_convert_addr(nor, addr); - ret = spi_nor_read_data(nor, addr, len, buf); + if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) + ret = spi_nor_octal_dtr_read(nor, addr, len, buf); + else + ret = spi_nor_read_data(nor, addr, len, buf); if (ret == 0) { /* We shouldn't see 0-length reads */ ret = -EIO;
On Octal DTR capable flashes like Micron Xcella reads cannot start or end at an odd address in Octal DTR mode. Extra bytes need to be read at the start or end to make sure both the start address and length remain even. To avoid allocating too much extra memory, thereby putting unnecessary memory pressure on the system, the temporary buffer containing the extra padding bytes is capped at PAGE_SIZE bytes. The rest of the 2-byte aligned part should be read directly in the main buffer. Signed-off-by: Pratyush Yadav <p.yadav@ti.com> --- drivers/mtd/spi-nor/core.c | 81 +++++++++++++++++++++++++++++++++++++- 1 file changed, 80 insertions(+), 1 deletion(-)