diff mbox series

[v2,1/3] arm64: dts: imx8mq: add Nitrogen8 SoM

Message ID 20210510185931.104780-1-l.stach@pengutronix.de (mailing list archive)
State New, archived
Headers show
Series [v2,1/3] arm64: dts: imx8mq: add Nitrogen8 SoM | expand

Commit Message

Lucas Stach May 10, 2021, 6:59 p.m. UTC 
From: Lucas Stach <dev@lynxeye.de>

This adds the description of the Nitrogen8 System on Module. The module
is quite simple with only a few (almost) fixed regulators and a eMMC
on-board.

The eMMC is currently limited to 50MHz modes via the pinctrl, as the board
has not wired up the data strobe line, which prevents HS400 mode from
working. As both the controller and the eMMC support this mode, it is
automatically selected when we allow the faster modes, leading to failing
transfers. Until we have a proper solution to only disable HS400 mode,
keep the eMMC at the slow bus modes.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
---
v2:
- remove 100/200MHz pinctrl states for usdhc1
- rename i2c nodes
---
 .../devicetree/bindings/arm/fsl.yaml          |   1 +
 .../dts/freescale/imx8mq-nitrogen-som.dtsi    | 242 ++++++++++++++++++
 2 files changed, 243 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-nitrogen-som.dtsi

Comments

Fabio Estevam May 11, 2021, 11:43 a.m. UTC | #1 
Hi Lucas,

On Mon, May 10, 2021 at 4:00 PM Lucas Stach <l.stach@pengutronix.de> wrote:
>
> From: Lucas Stach <dev@lynxeye.de>
>
> This adds the description of the Nitrogen8 System on Module. The module
> is quite simple with only a few (almost) fixed regulators and a eMMC
> on-board.
>
> The eMMC is currently limited to 50MHz modes via the pinctrl, as the board
> has not wired up the data strobe line, which prevents HS400 mode from
> working. As both the controller and the eMMC support this mode, it is
> automatically selected when we allow the faster modes, leading to failing
> transfers. Until we have a proper solution to only disable HS400 mode,
> keep the eMMC at the slow bus modes.
>
> Signed-off-by: Lucas Stach <dev@lynxeye.de>

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Rob Herring (Arm) May 11, 2021, 7:03 p.m. UTC | #2 
On Mon, 10 May 2021 20:59:29 +0200, Lucas Stach wrote:
> From: Lucas Stach <dev@lynxeye.de>
> 
> This adds the description of the Nitrogen8 System on Module. The module
> is quite simple with only a few (almost) fixed regulators and a eMMC
> on-board.
> 
> The eMMC is currently limited to 50MHz modes via the pinctrl, as the board
> has not wired up the data strobe line, which prevents HS400 mode from
> working. As both the controller and the eMMC support this mode, it is
> automatically selected when we allow the faster modes, leading to failing
> transfers. Until we have a proper solution to only disable HS400 mode,
> keep the eMMC at the slow bus modes.
> 
> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> ---
> v2:
> - remove 100/200MHz pinctrl states for usdhc1
> - rename i2c nodes
> ---
>  .../devicetree/bindings/arm/fsl.yaml          |   1 +
>  .../dts/freescale/imx8mq-nitrogen-som.dtsi    | 242 ++++++++++++++++++
>  2 files changed, 243 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-nitrogen-som.dtsi
> 

Reviewed-by: Rob Herring <robh@kernel.org>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 297c87f45db8..15519cc2d2c0 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -730,6 +730,7 @@  properties:
         items:
           - enum:
               - boundary,imx8mq-nitrogen8m # i.MX8MQ NITROGEN Board
+              - boundary,imx8mq-nitrogen8m-som # i.MX8MQ NITROGEN SoM
               - einfochips,imx8mq-thor96  # i.MX8MQ Thor96 Board
               - fsl,imx8mq-evk            # i.MX8MQ EVK Board
               - google,imx8mq-phanbell    # Google Coral Edge TPU
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen-som.dtsi
new file mode 100644
index 000000000000..7f20d9b9ffb3
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen-som.dtsi
@@ -0,0 +1,242 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2018 Boundary Devices
+ * Copyright 2021 Lucas Stach <dev@lynxeye.de>
+ */
+
+#include "imx8mq.dtsi"
+
+/ {
+	model = "Boundary Devices i.MX8MQ Nitrogen8M";
+	compatible = "boundary,imx8mq-nitrogen8m-som", "fsl,imx8mq";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	reg_1p8v: regulator-fixed-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_snvs: regulator-fixed-snvs {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_SNVS";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&{/opp-table/opp-800000000} {
+	opp-microvolt = <1000000>;
+};
+
+&{/opp-table/opp-1000000000} {
+	opp-microvolt = <1000000>;
+};
+
+&A53_0 {
+	cpu-supply = <&reg_arm_dram>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_arm_dram>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_arm_dram>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_arm_dram>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@4 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <4>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c1_pca9546>;
+		reg = <0x70>;
+		reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c1a: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg_arm_dram: regulator@60 {
+				compatible = "fcs,fan53555";
+				reg = <0x60>;
+				regulator-name = "VDD_ARM_DRAM_1V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+		};
+
+		i2c1b: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg_dram_1p1v: regulator@60 {
+				compatible = "fcs,fan53555";
+				reg = <0x60>;
+				regulator-name = "NVCC_DRAM_1P1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+		};
+
+		i2c1c: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg_soc_gpu_vpu: regulator@60 {
+				compatible = "fcs,fan53555";
+				reg = <0x60>;
+				regulator-name = "VDD_SOC_GPU_VPU";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-always-on;
+			};
+		};
+
+		i2c1d: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&pgc_gpu {
+	power-supply = <&reg_soc_gpu_vpu>;
+};
+
+&pgc_vpu {
+	power-supply = <&reg_soc_gpu_vpu>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usdhc1 {
+	assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	vqmmc-supply = <&reg_1p8v>;
+	vmmc-supply = <&reg_snvs>;
+	bus-width = <8>;
+	non-removable;
+	no-sdio;
+	no-sd;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO		0x23
+			MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
+			MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x59
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_i2c1_pca9546: i2c1-pca9546grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x49
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x45
+			MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX		0x45
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
+			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc3
+			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc3
+			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc3
+			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc3
+			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc3
+			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc3
+			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc3
+			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc3
+			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc3
+			MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
+		>;
+	};
+};