| Message ID | 20210518034119.2116555-1-srinivas.pandruvada@linux.intel.com (mailing list archive) |
|---|---|
| State | Mainlined, archived |
| Headers | show |
| Series | [v2] ACPI: DPTF: Add new PCH FIVR methods | expand |
On Tue, May 18, 2021 at 5:42 AM Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> wrote: > > Some additional information is required for updating PCH FIVR values > upon WiFi channel changes. > > New attributes added to the existing sysfs: > fivr_switching_freq_mhz : Get the FIVR switching control frequency > using ACPI method GFCS. Refer to the > documentation for the equation. > fivr_switching_fault_status: Read the FIVR switching frequency control > fault status. Uses ACPI method GFFS > > ssc_clock_info : Presents SSC (spread spectrum clock) information for EMI > (Electro magnetic interference) control. Use ACPI method GEMI. Refer > to the description of GEMI method below. > > GFFS > This ACPI method is used to read the FIVR switching frequency control > fault status. > Bits Description > [0:0] Fault status when set to 1 > [31:1] Reserved > > GFCS > This ACPI method is used to read the FIVR switching control > frequency. > Bits Description > [11:0] Actual Frequency = value * XTAL_FREQ / 128 > [31:12] Reserved > > GEMI > This ACPI method is used to read the programmed register value for EMI > (Electro magnetic interference) control. > > Bits Description > [7:0] Sets clock spectrum spread percentage: > 0x00=0.2% , 0x3F=10% > 1 LSB = 0.1% increase in spread (for > settings 0x01 thru 0x1C) > 1 LSB = 0.2% increase in spread (for > settings 0x1E thru 0x3F) > [8] When set to 1, enables spread > spectrum clock > [9] 0: Triangle mode. FFC frequency > walks around the Fcenter in a linear > fashion > 1: Random walk mode. FFC frequency > changes randomly within the SSC > (Spread spectrum clock) range > [10] 0: No white noise. 1: Add white noise > to spread waveform > [11] When 1, future writes are ignored. > > Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> > --- > v2 > Update documentation for fivr_switching_freq_mhz > > Documentation/ABI/testing/sysfs-platform-dptf | 42 +++++++++++++++++++ > drivers/acpi/dptf/dptf_pch_fivr.c | 9 ++++ > 2 files changed, 51 insertions(+) > > diff --git a/Documentation/ABI/testing/sysfs-platform-dptf b/Documentation/ABI/testing/sysfs-platform-dptf > index 141834342a4d..fe62f024eb93 100644 > --- a/Documentation/ABI/testing/sysfs-platform-dptf > +++ b/Documentation/ABI/testing/sysfs-platform-dptf > @@ -111,3 +111,45 @@ Contact: linux-acpi@vger.kernel.org > Description: > (RW) The PCH FIVR (Fully Integrated Voltage Regulator) switching frequency in MHz, > when FIVR clock is 38.4MHz. > + > +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fivr_switching_freq_mhz > +Date: June, 2021 > +KernelVersion: v5.14 > +Contact: linux-acpi@vger.kernel.org > +Description: > + (RO) Get the FIVR switching control frequency in MHz after applying equation > + "fivr_switching_freq_mhz * XTAL_FREQ / 128". Here XTAL_FREQ is Crystal Oscillator frequency > + in MHz, which is product specific. IMO it would be sufficient to say the following here: + (RO) PCH FIVR switching control frequency in the units of XTAL_FREQ / 128, + where XTAL_FREQ is the Crystal Oscillator frequency (product specific). This means that it needs to be multiplied by XTAL_FREQ / 128 to get the frequency in the whatever units XTAL_FREQ is expressed. I can make this change when applying the patch. > + > +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fivr_switching_fault_status > +Date: June, 2021 > +KernelVersion: v5.14 > +Contact: linux-acpi@vger.kernel.org > +Description: > + (RO) Read the FIVR switching frequency control fault status. > + > +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/ssc_clock_info > +Date: June, 2021 > +KernelVersion: v5.14 > +Contact: linux-acpi@vger.kernel.org > +Description: > + (RO) Presents SSC (spread spectrum clock) information for EMI > + (Electro magnetic interference) control. This is a bit mask. > + Bits Description > + [7:0] Sets clock spectrum spread percentage: > + 0x00=0.2% , 0x3F=10% > + 1 LSB = 0.1% increase in spread (for > + settings 0x01 thru 0x1C) > + 1 LSB = 0.2% increase in spread (for > + settings 0x1E thru 0x3F) > + [8] When set to 1, enables spread > + spectrum clock > + [9] 0: Triangle mode. FFC frequency > + walks around the Fcenter in a linear > + fashion > + 1: Random walk mode. FFC frequency > + changes randomly within the SSC > + (Spread spectrum clock) range > + [10] 0: No white noise. 1: Add white noise > + to spread waveform > + [11] When 1, future writes are ignored. > diff --git a/drivers/acpi/dptf/dptf_pch_fivr.c b/drivers/acpi/dptf/dptf_pch_fivr.c > index 5fca18296bf6..22c4ae0401ef 100644 > --- a/drivers/acpi/dptf/dptf_pch_fivr.c > +++ b/drivers/acpi/dptf/dptf_pch_fivr.c > @@ -55,15 +55,24 @@ static ssize_t name##_store(struct device *dev,\ > > PCH_FIVR_SHOW(freq_mhz_low_clock, GFC0) > PCH_FIVR_SHOW(freq_mhz_high_clock, GFC1) > +PCH_FIVR_SHOW(ssc_clock_info, GEMI) > +PCH_FIVR_SHOW(fivr_switching_freq_mhz, GFCS) > +PCH_FIVR_SHOW(fivr_switching_fault_status, GFFS) > PCH_FIVR_STORE(freq_mhz_low_clock, RFC0) > PCH_FIVR_STORE(freq_mhz_high_clock, RFC1) > > static DEVICE_ATTR_RW(freq_mhz_low_clock); > static DEVICE_ATTR_RW(freq_mhz_high_clock); > +static DEVICE_ATTR_RO(ssc_clock_info); > +static DEVICE_ATTR_RO(fivr_switching_freq_mhz); > +static DEVICE_ATTR_RO(fivr_switching_fault_status); > > static struct attribute *fivr_attrs[] = { > &dev_attr_freq_mhz_low_clock.attr, > &dev_attr_freq_mhz_high_clock.attr, > + &dev_attr_ssc_clock_info.attr, > + &dev_attr_fivr_switching_freq_mhz.attr, > + &dev_attr_fivr_switching_fault_status.attr, > NULL > }; > > -- > 2.27.0 >
On Tue, 2021-05-18 at 11:36 +0200, Rafael J. Wysocki wrote: > On Tue, May 18, 2021 at 5:42 AM Srinivas Pandruvada > <srinivas.pandruvada@linux.intel.com> wrote: > > > > Some additional information is required for updating PCH FIVR > > values > > upon WiFi channel changes. > > > > New attributes added to the existing sysfs: > > fivr_switching_freq_mhz : Get the FIVR switching control frequency > > using ACPI method GFCS. Refer to the > > documentation for the equation. > > fivr_switching_fault_status: Read the FIVR switching frequency > > control > > fault status. Uses ACPI method GFFS > > > > ssc_clock_info : Presents SSC (spread spectrum clock) information > > for EMI > > (Electro magnetic interference) control. Use ACPI method GEMI. > > Refer > > to the description of GEMI method below. > > > > GFFS > > This ACPI method is used to read the FIVR switching frequency > > control > > fault status. > > Bits Description > > [0:0] Fault status when set to 1 > > [31:1] Reserved > > > > GFCS > > This ACPI method is used to read the FIVR switching control > > frequency. > > Bits Description > > [11:0] Actual Frequency = value * XTAL_FREQ / 128 > > [31:12] Reserved > > > > GEMI > > This ACPI method is used to read the programmed register value for > > EMI > > (Electro magnetic interference) control. > > > > Bits Description > > [7:0] Sets clock spectrum spread percentage: > > 0x00=0.2% , 0x3F=10% > > 1 LSB = 0.1% increase in spread (for > > settings 0x01 thru 0x1C) > > 1 LSB = 0.2% increase in spread (for > > settings 0x1E thru 0x3F) > > [8] When set to 1, enables spread > > spectrum clock > > [9] 0: Triangle mode. FFC frequency > > walks around the Fcenter in a linear > > fashion > > 1: Random walk mode. FFC frequency > > changes randomly within the SSC > > (Spread spectrum clock) range > > [10] 0: No white noise. 1: Add white noise > > to spread waveform > > [11] When 1, future writes are ignored. > > > > Signed-off-by: Srinivas Pandruvada < > > srinivas.pandruvada@linux.intel.com> > > --- > > v2 > > Update documentation for fivr_switching_freq_mhz > > > > Documentation/ABI/testing/sysfs-platform-dptf | 42 > > +++++++++++++++++++ > > drivers/acpi/dptf/dptf_pch_fivr.c | 9 ++++ > > 2 files changed, 51 insertions(+) > > > > diff --git a/Documentation/ABI/testing/sysfs-platform-dptf > > b/Documentation/ABI/testing/sysfs-platform-dptf > > index 141834342a4d..fe62f024eb93 100644 > > --- a/Documentation/ABI/testing/sysfs-platform-dptf > > +++ b/Documentation/ABI/testing/sysfs-platform-dptf > > @@ -111,3 +111,45 @@ Contact: linux-acpi@vger.kernel.org > > Description: > > (RW) The PCH FIVR (Fully Integrated Voltage > > Regulator) switching frequency in MHz, > > when FIVR clock is 38.4MHz. > > + > > +What: > > /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fiv > > r_switching_freq_mhz > > +Date: June, 2021 > > +KernelVersion: v5.14 > > +Contact: linux-acpi@vger.kernel.org > > +Description: > > + (RO) Get the FIVR switching control frequency in > > MHz after applying equation > > + "fivr_switching_freq_mhz * XTAL_FREQ / 128". Here > > XTAL_FREQ is Crystal Oscillator frequency > > + in MHz, which is product specific. > > IMO it would be sufficient to say the following here: > > + (RO) PCH FIVR switching control frequency in the > units > of XTAL_FREQ / 128, > + where XTAL_FREQ is the Crystal Oscillator frequency > (product specific). > > This means that it needs to be multiplied by XTAL_FREQ / 128 to get > the frequency in the whatever units XTAL_FREQ is expressed. > Looks good. > I can make this change when applying the patch. > Thanks, Srinivas > > +What: > > /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fiv > > r_switching_fault_status > > +Date: June, 2021 > > +KernelVersion: v5.14 > > +Contact: linux-acpi@vger.kernel.org > > +Description: > > + (RO) Read the FIVR switching frequency control > > fault status. > > + > > +What: > > /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/ssc > > _clock_info > > +Date: June, 2021 > > +KernelVersion: v5.14 > > +Contact: linux-acpi@vger.kernel.org > > +Description: > > + (RO) Presents SSC (spread spectrum clock) > > information for EMI > > + (Electro magnetic interference) control. This is a > > bit mask. > > + Bits Description > > + [7:0] Sets clock spectrum spread percentage: > > + 0x00=0.2% , 0x3F=10% > > + 1 LSB = 0.1% increase in spread (for > > + settings 0x01 thru 0x1C) > > + 1 LSB = 0.2% increase in spread (for > > + settings 0x1E thru 0x3F) > > + [8] When set to 1, enables spread > > + spectrum clock > > + [9] 0: Triangle mode. FFC frequency > > + walks around the Fcenter in a linear > > + fashion > > + 1: Random walk mode. FFC frequency > > + changes randomly within the SSC > > + (Spread spectrum clock) range > > + [10] 0: No white noise. 1: Add white noise > > + to spread waveform > > + [11] When 1, future writes are ignored. > > diff --git a/drivers/acpi/dptf/dptf_pch_fivr.c > > b/drivers/acpi/dptf/dptf_pch_fivr.c > > index 5fca18296bf6..22c4ae0401ef 100644 > > --- a/drivers/acpi/dptf/dptf_pch_fivr.c > > +++ b/drivers/acpi/dptf/dptf_pch_fivr.c > > @@ -55,15 +55,24 @@ static ssize_t name##_store(struct device > > *dev,\ > > > > PCH_FIVR_SHOW(freq_mhz_low_clock, GFC0) > > PCH_FIVR_SHOW(freq_mhz_high_clock, GFC1) > > +PCH_FIVR_SHOW(ssc_clock_info, GEMI) > > +PCH_FIVR_SHOW(fivr_switching_freq_mhz, GFCS) > > +PCH_FIVR_SHOW(fivr_switching_fault_status, GFFS) > > PCH_FIVR_STORE(freq_mhz_low_clock, RFC0) > > PCH_FIVR_STORE(freq_mhz_high_clock, RFC1) > > > > static DEVICE_ATTR_RW(freq_mhz_low_clock); > > static DEVICE_ATTR_RW(freq_mhz_high_clock); > > +static DEVICE_ATTR_RO(ssc_clock_info); > > +static DEVICE_ATTR_RO(fivr_switching_freq_mhz); > > +static DEVICE_ATTR_RO(fivr_switching_fault_status); > > > > static struct attribute *fivr_attrs[] = { > > &dev_attr_freq_mhz_low_clock.attr, > > &dev_attr_freq_mhz_high_clock.attr, > > + &dev_attr_ssc_clock_info.attr, > > + &dev_attr_fivr_switching_freq_mhz.attr, > > + &dev_attr_fivr_switching_fault_status.attr, > > NULL > > }; > > > > -- > > 2.27.0 > >
On Tue, May 18, 2021 at 12:27 PM Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> wrote: > > On Tue, 2021-05-18 at 11:36 +0200, Rafael J. Wysocki wrote: > > On Tue, May 18, 2021 at 5:42 AM Srinivas Pandruvada > > <srinivas.pandruvada@linux.intel.com> wrote: > > > > > > Some additional information is required for updating PCH FIVR > > > values > > > upon WiFi channel changes. > > > > > > New attributes added to the existing sysfs: > > > fivr_switching_freq_mhz : Get the FIVR switching control frequency > > > using ACPI method GFCS. Refer to the > > > documentation for the equation. > > > fivr_switching_fault_status: Read the FIVR switching frequency > > > control > > > fault status. Uses ACPI method GFFS > > > > > > ssc_clock_info : Presents SSC (spread spectrum clock) information > > > for EMI > > > (Electro magnetic interference) control. Use ACPI method GEMI. > > > Refer > > > to the description of GEMI method below. > > > > > > GFFS > > > This ACPI method is used to read the FIVR switching frequency > > > control > > > fault status. > > > Bits Description > > > [0:0] Fault status when set to 1 > > > [31:1] Reserved > > > > > > GFCS > > > This ACPI method is used to read the FIVR switching control > > > frequency. > > > Bits Description > > > [11:0] Actual Frequency = value * XTAL_FREQ / 128 > > > [31:12] Reserved > > > > > > GEMI > > > This ACPI method is used to read the programmed register value for > > > EMI > > > (Electro magnetic interference) control. > > > > > > Bits Description > > > [7:0] Sets clock spectrum spread percentage: > > > 0x00=0.2% , 0x3F=10% > > > 1 LSB = 0.1% increase in spread (for > > > settings 0x01 thru 0x1C) > > > 1 LSB = 0.2% increase in spread (for > > > settings 0x1E thru 0x3F) > > > [8] When set to 1, enables spread > > > spectrum clock > > > [9] 0: Triangle mode. FFC frequency > > > walks around the Fcenter in a linear > > > fashion > > > 1: Random walk mode. FFC frequency > > > changes randomly within the SSC > > > (Spread spectrum clock) range > > > [10] 0: No white noise. 1: Add white noise > > > to spread waveform > > > [11] When 1, future writes are ignored. > > > > > > Signed-off-by: Srinivas Pandruvada < > > > srinivas.pandruvada@linux.intel.com> > > > --- > > > v2 > > > Update documentation for fivr_switching_freq_mhz > > > > > > Documentation/ABI/testing/sysfs-platform-dptf | 42 > > > +++++++++++++++++++ > > > drivers/acpi/dptf/dptf_pch_fivr.c | 9 ++++ > > > 2 files changed, 51 insertions(+) > > > > > > diff --git a/Documentation/ABI/testing/sysfs-platform-dptf > > > b/Documentation/ABI/testing/sysfs-platform-dptf > > > index 141834342a4d..fe62f024eb93 100644 > > > --- a/Documentation/ABI/testing/sysfs-platform-dptf > > > +++ b/Documentation/ABI/testing/sysfs-platform-dptf > > > @@ -111,3 +111,45 @@ Contact: linux-acpi@vger.kernel.org > > > Description: > > > (RW) The PCH FIVR (Fully Integrated Voltage > > > Regulator) switching frequency in MHz, > > > when FIVR clock is 38.4MHz. > > > + > > > +What: > > > /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fiv > > > r_switching_freq_mhz > > > +Date: June, 2021 > > > +KernelVersion: v5.14 > > > +Contact: linux-acpi@vger.kernel.org > > > +Description: > > > + (RO) Get the FIVR switching control frequency in > > > MHz after applying equation > > > + "fivr_switching_freq_mhz * XTAL_FREQ / 128". Here > > > XTAL_FREQ is Crystal Oscillator frequency > > > + in MHz, which is product specific. > > > > IMO it would be sufficient to say the following here: > > > > + (RO) PCH FIVR switching control frequency in the > > units > > of XTAL_FREQ / 128, > > + where XTAL_FREQ is the Crystal Oscillator frequency > > (product specific). > > > > This means that it needs to be multiplied by XTAL_FREQ / 128 to get > > the frequency in the whatever units XTAL_FREQ is expressed. > > > Looks good. So applied as 5.14 material, thanks!
diff --git a/Documentation/ABI/testing/sysfs-platform-dptf b/Documentation/ABI/testing/sysfs-platform-dptf index 141834342a4d..fe62f024eb93 100644 --- a/Documentation/ABI/testing/sysfs-platform-dptf +++ b/Documentation/ABI/testing/sysfs-platform-dptf @@ -111,3 +111,45 @@ Contact: linux-acpi@vger.kernel.org Description: (RW) The PCH FIVR (Fully Integrated Voltage Regulator) switching frequency in MHz, when FIVR clock is 38.4MHz. + +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fivr_switching_freq_mhz +Date: June, 2021 +KernelVersion: v5.14 +Contact: linux-acpi@vger.kernel.org +Description: + (RO) Get the FIVR switching control frequency in MHz after applying equation + "fivr_switching_freq_mhz * XTAL_FREQ / 128". Here XTAL_FREQ is Crystal Oscillator frequency + in MHz, which is product specific. + +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fivr_switching_fault_status +Date: June, 2021 +KernelVersion: v5.14 +Contact: linux-acpi@vger.kernel.org +Description: + (RO) Read the FIVR switching frequency control fault status. + +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/ssc_clock_info +Date: June, 2021 +KernelVersion: v5.14 +Contact: linux-acpi@vger.kernel.org +Description: + (RO) Presents SSC (spread spectrum clock) information for EMI + (Electro magnetic interference) control. This is a bit mask. + Bits Description + [7:0] Sets clock spectrum spread percentage: + 0x00=0.2% , 0x3F=10% + 1 LSB = 0.1% increase in spread (for + settings 0x01 thru 0x1C) + 1 LSB = 0.2% increase in spread (for + settings 0x1E thru 0x3F) + [8] When set to 1, enables spread + spectrum clock + [9] 0: Triangle mode. FFC frequency + walks around the Fcenter in a linear + fashion + 1: Random walk mode. FFC frequency + changes randomly within the SSC + (Spread spectrum clock) range + [10] 0: No white noise. 1: Add white noise + to spread waveform + [11] When 1, future writes are ignored. diff --git a/drivers/acpi/dptf/dptf_pch_fivr.c b/drivers/acpi/dptf/dptf_pch_fivr.c index 5fca18296bf6..22c4ae0401ef 100644 --- a/drivers/acpi/dptf/dptf_pch_fivr.c +++ b/drivers/acpi/dptf/dptf_pch_fivr.c @@ -55,15 +55,24 @@ static ssize_t name##_store(struct device *dev,\ PCH_FIVR_SHOW(freq_mhz_low_clock, GFC0) PCH_FIVR_SHOW(freq_mhz_high_clock, GFC1) +PCH_FIVR_SHOW(ssc_clock_info, GEMI) +PCH_FIVR_SHOW(fivr_switching_freq_mhz, GFCS) +PCH_FIVR_SHOW(fivr_switching_fault_status, GFFS) PCH_FIVR_STORE(freq_mhz_low_clock, RFC0) PCH_FIVR_STORE(freq_mhz_high_clock, RFC1) static DEVICE_ATTR_RW(freq_mhz_low_clock); static DEVICE_ATTR_RW(freq_mhz_high_clock); +static DEVICE_ATTR_RO(ssc_clock_info); +static DEVICE_ATTR_RO(fivr_switching_freq_mhz); +static DEVICE_ATTR_RO(fivr_switching_fault_status); static struct attribute *fivr_attrs[] = { &dev_attr_freq_mhz_low_clock.attr, &dev_attr_freq_mhz_high_clock.attr, + &dev_attr_ssc_clock_info.attr, + &dev_attr_fivr_switching_freq_mhz.attr, + &dev_attr_fivr_switching_fault_status.attr, NULL };
Some additional information is required for updating PCH FIVR values upon WiFi channel changes. New attributes added to the existing sysfs: fivr_switching_freq_mhz : Get the FIVR switching control frequency using ACPI method GFCS. Refer to the documentation for the equation. fivr_switching_fault_status: Read the FIVR switching frequency control fault status. Uses ACPI method GFFS ssc_clock_info : Presents SSC (spread spectrum clock) information for EMI (Electro magnetic interference) control. Use ACPI method GEMI. Refer to the description of GEMI method below. GFFS This ACPI method is used to read the FIVR switching frequency control fault status. Bits Description [0:0] Fault status when set to 1 [31:1] Reserved GFCS This ACPI method is used to read the FIVR switching control frequency. Bits Description [11:0] Actual Frequency = value * XTAL_FREQ / 128 [31:12] Reserved GEMI This ACPI method is used to read the programmed register value for EMI (Electro magnetic interference) control. Bits Description [7:0] Sets clock spectrum spread percentage: 0x00=0.2% , 0x3F=10% 1 LSB = 0.1% increase in spread (for settings 0x01 thru 0x1C) 1 LSB = 0.2% increase in spread (for settings 0x1E thru 0x3F) [8] When set to 1, enables spread spectrum clock [9] 0: Triangle mode. FFC frequency walks around the Fcenter in a linear fashion 1: Random walk mode. FFC frequency changes randomly within the SSC (Spread spectrum clock) range [10] 0: No white noise. 1: Add white noise to spread waveform [11] When 1, future writes are ignored. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> --- v2 Update documentation for fivr_switching_freq_mhz Documentation/ABI/testing/sysfs-platform-dptf | 42 +++++++++++++++++++ drivers/acpi/dptf/dptf_pch_fivr.c | 9 ++++ 2 files changed, 51 insertions(+)