| Message ID | 20210608022644.21074-2-jon.lin@rock-chips.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add Rockchip SFC(serial flash controller) support | expand |
Hi Jon, A look at the build log shows this error: https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20210608022644.21074-2-jon.lin@rock-chips.com/ dtschema/dtc warnings/errors: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml: spi@ff3a0000: clock-names:0: 'hclk_sfc' was expected From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml: spi@ff3a0000: clock-names:1: 'clk_sfc' was expected From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml Check document with: make ARCH=arm dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml make ARCH=arm dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml Remove any errors before submitting. === Johan On 6/8/21 4:26 AM, Jon Lin wrote: > From: Chris Morgan <macromorgan@hotmail.com> > > Add bindings for the Rockchip serial flash controller. New device > specific parameter of rockchip,sfc-no-dma included in documentation. > > Signed-off-by: Chris Morgan <macromorgan@hotmail.com> > Signed-off-by: Jon Lin <jon.lin@rock-chips.com> > --- > > Changes in v6: > - Add support in device trees for rv1126(Declared in series 5 but not > submitted) > - Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not > affect interpretation and has been widely used > - Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted) > - Simplify the code, such as remove "rockchip_sfc_register_all"(Declared > in series 5 but not submitted) > - Support SFC ver4 ver5(Declared in series 5 but not submitted) > - Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c > - Change to use devm_spi_alloc_master and spi_unregister_master > > Changes in v5: > - Add support in device trees for rv1126 > - Support sfc tx_dual, tx_quad > - Simplify the code, such as remove "rockchip_sfc_register_all" > - Support SFC ver4 ver5 > > Changes in v4: > - Changing patch back to an "RFC". An engineer from Rockchip > reached out to me to let me know they are working on this patch for > upstream, I am submitting this v4 for the community to see however > I expect Jon Lin (jon.lin@rock-chips.com) will submit new patches > soon and these are the ones we should pursue for mainlining. Jon's > patch series should include support for more hardware than this > series. > - Clean up documentation more and ensure it is correct per > make dt_binding_check. > - Add support in device trees for rk3036, rk3308, and rv1108. > - Add ahb clock (hclk_sfc) support for rk3036. > - Change rockchip_sfc_wait_fifo_ready() to use a switch statement. > - Change IRQ code to only mark IRQ as handled if it handles the > specific IRQ (DMA transfer finish) it is supposed to handle. > > Changes in v3: > - Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc). > - Changed the compatible string from rockchip,sfc to > rockchip,rk3036-sfc. A quick glance at the datasheets suggests this > driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and > RV1108 SoCs, and possibly more. However, I am currently only able > to test this on a PX30 (an RK3326). The technical reference manuals > appear to list the same registers for each device. > - Corrected devicetree documentation for formatting and to note these > changes. > - Replaced the maintainer with Heiko Stuebner and myself, as we will > take ownership of this going forward. > - Noted that the device (per the reference manual) supports 4 CS, but > I am only able to test a single CS (CS 0). > - Reordered patches to comply with upstream rules. > > Changes in v2: > - Reimplemented driver using spi-mem subsystem. > - Removed power management code as I couldn't get it working properly. > - Added device tree bindings for Odroid Go Advance. > > Changes in v1: > hanges made in this new series versus the v8 of the old series: > - Added function to read spi-rx-bus-width from device tree, in the > event that the SPI chip supports 4x mode but only has 2 pins > wired (such as the Odroid Go Advance). > - Changed device tree documentation from txt to yaml format. > - Made "reset" message a dev_dbg from a dev_info. > - Changed read and write fifo functions to remove redundant checks. > - Changed the write and read from relaxed to non-relaxed when > starting the DMA transfer or reading the DMA IRQ. > - Changed from dma_coerce_mask_and_coherent to just > dma_set_mask_and_coherent. > - Changed name of get_if_type to rockchip_sfc_get_if_type. > > .../devicetree/bindings/spi/rockchip-sfc.yaml | 87 +++++++++++++++++++ > 1 file changed, 87 insertions(+) > create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml > > diff --git a/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml > new file mode 100644 > index 000000000000..160449713f97 > --- /dev/null > +++ b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml > @@ -0,0 +1,87 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Rockchip Serial Flash Controller (SFC) > + > +maintainers: > + - Heiko Stuebner <heiko@sntech.de> > + - Chris Morgan <macromorgan@hotmail.com> In the driver spi-rockchip-sfc.c is used: Chris Morgan <macroalpha82@gmail.com> Maybe use a consistent email address? Also Hotmail does strange things to message-ID's and links/content inside patches. > + > +allOf: > + - $ref: spi-controller.yaml# > + > +properties: > + compatible: > + oneOf: > + - const: rockchip,rk3036-sfc > + - items: > + - enum: > + - rockchip,px30-sfc > + - rockchip,rk3308-sfc > + - rockchip,rv1108-sfc > + - const: rockchip,rk3036-sfc > + - const: rockchip,rv1126-sfc A look at the driver shows this: +static const struct of_device_id rockchip_sfc_dt_ids[] = { + { .compatible = "rockchip,px30-sfc"}, remove + { .compatible = "rockchip,rk3036-sfc"}, + { .compatible = "rockchip,rk3308-sfc"}, + { .compatible = "rockchip,rv1126-sfc"}, remove + { /* sentinel */ } +}; When no '.data = &my_sfc_data' exist then there's no need for additional compatible strings in the driver. === example for I2S: { .compatible = "rockchip,rk3399-i2s", .data = &rk3399_i2s_pins }, === Compatibility strings are supposed to be SoC orientated. With rockchip_sfc_get_version() all we need is one fall back string for now I think. Is rk3568 identical. Please advise. - const: rockchip,rk3036-sfc - items: - enum: - rockchip,px30-sfc - rockchip,rk3308-sfc - rockchip,rk3368-sfc - rockchip,rk3568-sfc - rockchip,rv1108-sfc - rockchip,rv1126-sfc - const: rockchip,rk3036-sfc === The rk3368 TRM also describes a SFC controller. For the mainline DT completeness is it possible to add a rk3368 SFC node as well? ;) > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + clocks: > + items: > + - description: Bus Clock > + - description: Module Clock > + > + clock-names: > + items: > + - const: hclk_sfc > + - const: clk_sfc > + > + power-domains: > + maxItems: 1 > + > + rockchip,sfc-no-dma: > + description: Disable DMA and utilize FIFO mode only > + type: boolean > + > +required: > + - compatible > + - reg > + - interrupts > + - clocks > + - clock-names > + > +unevaluatedProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/px30-cru.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/power/px30-power.h> > + > + sfc: spi@ff3a0000 { > + compatible = "rockchip,px30-sfc","rockchip,rk3036-sfc"; > + reg = <0xff3a0000 0x4000>; > + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>; > + clock-names = "clk_sfc", "hclk_sfc"; The clocks in the examples and dtsi files must have the same sort order. > + pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>; > + pinctrl-names = "default"; > + power-domains = <&power PX30_PD_MMC_NAND>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + flash@0 { From spi-controller.yaml: patternProperties: "^.*@[0-9a-f]+$": type: object properties: compatible: description: Compatible of the SPI device. reg: minimum: 0 maximum: 256 description: Chip select used by the device. This allows 257 sub nodes. Support up to 4 chip select in the driver. #define SFC_MAX_CHIPSELECT_NUM 4 > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <108000000>; > + spi-rx-bus-width = <2>; > + spi-tx-bus-width = <2>; > + }; > + }; > + > +... >
On Tue, 08 Jun 2021 10:26:37 +0800, Jon Lin wrote: > From: Chris Morgan <macromorgan@hotmail.com> > > Add bindings for the Rockchip serial flash controller. New device > specific parameter of rockchip,sfc-no-dma included in documentation. > > Signed-off-by: Chris Morgan <macromorgan@hotmail.com> > Signed-off-by: Jon Lin <jon.lin@rock-chips.com> > --- > > Changes in v6: > - Add support in device trees for rv1126(Declared in series 5 but not > submitted) > - Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not > affect interpretation and has been widely used > - Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted) > - Simplify the code, such as remove "rockchip_sfc_register_all"(Declared > in series 5 but not submitted) > - Support SFC ver4 ver5(Declared in series 5 but not submitted) > - Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c > - Change to use devm_spi_alloc_master and spi_unregister_master > > Changes in v5: > - Add support in device trees for rv1126 > - Support sfc tx_dual, tx_quad > - Simplify the code, such as remove "rockchip_sfc_register_all" > - Support SFC ver4 ver5 > > Changes in v4: > - Changing patch back to an "RFC". An engineer from Rockchip > reached out to me to let me know they are working on this patch for > upstream, I am submitting this v4 for the community to see however > I expect Jon Lin (jon.lin@rock-chips.com) will submit new patches > soon and these are the ones we should pursue for mainlining. Jon's > patch series should include support for more hardware than this > series. > - Clean up documentation more and ensure it is correct per > make dt_binding_check. > - Add support in device trees for rk3036, rk3308, and rv1108. > - Add ahb clock (hclk_sfc) support for rk3036. > - Change rockchip_sfc_wait_fifo_ready() to use a switch statement. > - Change IRQ code to only mark IRQ as handled if it handles the > specific IRQ (DMA transfer finish) it is supposed to handle. > > Changes in v3: > - Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc). > - Changed the compatible string from rockchip,sfc to > rockchip,rk3036-sfc. A quick glance at the datasheets suggests this > driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and > RV1108 SoCs, and possibly more. However, I am currently only able > to test this on a PX30 (an RK3326). The technical reference manuals > appear to list the same registers for each device. > - Corrected devicetree documentation for formatting and to note these > changes. > - Replaced the maintainer with Heiko Stuebner and myself, as we will > take ownership of this going forward. > - Noted that the device (per the reference manual) supports 4 CS, but > I am only able to test a single CS (CS 0). > - Reordered patches to comply with upstream rules. > > Changes in v2: > - Reimplemented driver using spi-mem subsystem. > - Removed power management code as I couldn't get it working properly. > - Added device tree bindings for Odroid Go Advance. > > Changes in v1: > hanges made in this new series versus the v8 of the old series: > - Added function to read spi-rx-bus-width from device tree, in the > event that the SPI chip supports 4x mode but only has 2 pins > wired (such as the Odroid Go Advance). > - Changed device tree documentation from txt to yaml format. > - Made "reset" message a dev_dbg from a dev_info. > - Changed read and write fifo functions to remove redundant checks. > - Changed the write and read from relaxed to non-relaxed when > starting the DMA transfer or reading the DMA IRQ. > - Changed from dma_coerce_mask_and_coherent to just > dma_set_mask_and_coherent. > - Changed name of get_if_type to rockchip_sfc_get_if_type. > > .../devicetree/bindings/spi/rockchip-sfc.yaml | 87 +++++++++++++++++++ > 1 file changed, 87 insertions(+) > create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml: spi@ff3a0000: clock-names:0: 'hclk_sfc' was expected From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml: spi@ff3a0000: clock-names:1: 'clk_sfc' was expected From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml \ndoc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/patch/1489062 This check can fail if there are any dependencies. The base for a patch series is generally the most recent rc1. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit.
On 6/9/21 2:03 AM, Johan Jonker wrote: > Hi Jon, > > A look at the build log shows this error: > > https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20210608022644.21074-2-jon.lin@rock-chips.com/ > > dtschema/dtc warnings/errors: > /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml: > spi@ff3a0000: clock-names:0: 'hclk_sfc' was expected > From schema: > /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml > /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml: > spi@ff3a0000: clock-names:1: 'clk_sfc' was expected > From schema: > /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml > > Check document with: > > make ARCH=arm dt_binding_check > DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml > > make ARCH=arm dtbs_check > DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml > > make ARCH=arm64 dtbs_check > DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml > > Remove any errors before submitting. > > === > > Johan > > On 6/8/21 4:26 AM, Jon Lin wrote: >> From: Chris Morgan <macromorgan@hotmail.com> >> >> Add bindings for the Rockchip serial flash controller. New device >> specific parameter of rockchip,sfc-no-dma included in documentation. >> >> Signed-off-by: Chris Morgan <macromorgan@hotmail.com> >> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> >> --- >> >> Changes in v6: >> - Add support in device trees for rv1126(Declared in series 5 but not >> submitted) >> - Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not >> affect interpretation and has been widely used >> - Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted) >> - Simplify the code, such as remove "rockchip_sfc_register_all"(Declared >> in series 5 but not submitted) >> - Support SFC ver4 ver5(Declared in series 5 but not submitted) >> - Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c >> - Change to use devm_spi_alloc_master and spi_unregister_master >> >> Changes in v5: >> - Add support in device trees for rv1126 >> - Support sfc tx_dual, tx_quad >> - Simplify the code, such as remove "rockchip_sfc_register_all" >> - Support SFC ver4 ver5 >> >> Changes in v4: >> - Changing patch back to an "RFC". An engineer from Rockchip >> reached out to me to let me know they are working on this patch for >> upstream, I am submitting this v4 for the community to see however >> I expect Jon Lin (jon.lin@rock-chips.com) will submit new patches >> soon and these are the ones we should pursue for mainlining. Jon's >> patch series should include support for more hardware than this >> series. >> - Clean up documentation more and ensure it is correct per >> make dt_binding_check. >> - Add support in device trees for rk3036, rk3308, and rv1108. >> - Add ahb clock (hclk_sfc) support for rk3036. >> - Change rockchip_sfc_wait_fifo_ready() to use a switch statement. >> - Change IRQ code to only mark IRQ as handled if it handles the >> specific IRQ (DMA transfer finish) it is supposed to handle. >> >> Changes in v3: >> - Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc). >> - Changed the compatible string from rockchip,sfc to >> rockchip,rk3036-sfc. A quick glance at the datasheets suggests this >> driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and >> RV1108 SoCs, and possibly more. However, I am currently only able >> to test this on a PX30 (an RK3326). The technical reference manuals >> appear to list the same registers for each device. >> - Corrected devicetree documentation for formatting and to note these >> changes. >> - Replaced the maintainer with Heiko Stuebner and myself, as we will >> take ownership of this going forward. >> - Noted that the device (per the reference manual) supports 4 CS, but >> I am only able to test a single CS (CS 0). >> - Reordered patches to comply with upstream rules. >> >> Changes in v2: >> - Reimplemented driver using spi-mem subsystem. >> - Removed power management code as I couldn't get it working properly. >> - Added device tree bindings for Odroid Go Advance. >> >> Changes in v1: >> hanges made in this new series versus the v8 of the old series: >> - Added function to read spi-rx-bus-width from device tree, in the >> event that the SPI chip supports 4x mode but only has 2 pins >> wired (such as the Odroid Go Advance). >> - Changed device tree documentation from txt to yaml format. >> - Made "reset" message a dev_dbg from a dev_info. >> - Changed read and write fifo functions to remove redundant checks. >> - Changed the write and read from relaxed to non-relaxed when >> starting the DMA transfer or reading the DMA IRQ. >> - Changed from dma_coerce_mask_and_coherent to just >> dma_set_mask_and_coherent. >> - Changed name of get_if_type to rockchip_sfc_get_if_type. >> >> .../devicetree/bindings/spi/rockchip-sfc.yaml | 87 +++++++++++++++++++ >> 1 file changed, 87 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >> >> diff --git a/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >> new file mode 100644 >> index 000000000000..160449713f97 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >> @@ -0,0 +1,87 @@ >> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Rockchip Serial Flash Controller (SFC) >> + >> +maintainers: >> + - Heiko Stuebner <heiko@sntech.de> >> + - Chris Morgan <macromorgan@hotmail.com> > In the driver spi-rockchip-sfc.c is used: > Chris Morgan <macroalpha82@gmail.com> > Maybe use a consistent email address? > Also Hotmail does strange things to message-ID's and links/content > inside patches. > >> + >> +allOf: >> + - $ref: spi-controller.yaml# >> + >> +properties: >> + compatible: >> + oneOf: >> + - const: rockchip,rk3036-sfc >> + - items: >> + - enum: >> + - rockchip,px30-sfc >> + - rockchip,rk3308-sfc >> + - rockchip,rv1108-sfc >> + - const: rockchip,rk3036-sfc >> + - const: rockchip,rv1126-sfc > A look at the driver shows this: > > +static const struct of_device_id rockchip_sfc_dt_ids[] = { > > + { .compatible = "rockchip,px30-sfc"}, > > remove > > + { .compatible = "rockchip,rk3036-sfc"}, > > + { .compatible = "rockchip,rk3308-sfc"}, > + { .compatible = "rockchip,rv1126-sfc"}, > > remove > > + { /* sentinel */ } > +}; > > When no '.data = &my_sfc_data' exist then there's no need for additional > compatible strings in the driver. > === > example for I2S: > { .compatible = "rockchip,rk3399-i2s", .data = &rk3399_i2s_pins }, > === > Compatibility strings are supposed to be SoC orientated. > With rockchip_sfc_get_version() all we need is one fall back string for > now I think. Is rk3568 identical. Please advise. > > > - const: rockchip,rk3036-sfc > - items: > - enum: > - rockchip,px30-sfc > - rockchip,rk3308-sfc > - rockchip,rk3368-sfc > - rockchip,rk3568-sfc > - rockchip,rv1108-sfc > - rockchip,rv1126-sfc > - const: rockchip,rk3036-sfc > > === > > The rk3368 TRM also describes a SFC controller. > For the mainline DT completeness is it possible to add a rk3368 SFC node > as well? ;) > >> + >> + reg: >> + maxItems: 1 >> + >> + interrupts: >> + maxItems: 1 >> + >> + clocks: >> + items: >> + - description: Bus Clock >> + - description: Module Clock >> + >> + clock-names: >> + items: >> + - const: hclk_sfc >> + - const: clk_sfc >> + >> + power-domains: >> + maxItems: 1 >> + >> + rockchip,sfc-no-dma: >> + description: Disable DMA and utilize FIFO mode only >> + type: boolean >> + >> +required: >> + - compatible >> + - reg >> + - interrupts >> + - clocks >> + - clock-names >> + >> +unevaluatedProperties: false >> + >> +examples: >> + - | >> + #include <dt-bindings/clock/px30-cru.h> >> + #include <dt-bindings/interrupt-controller/arm-gic.h> >> + #include <dt-bindings/power/px30-power.h> >> + >> + sfc: spi@ff3a0000 { >> + compatible = "rockchip,px30-sfc","rockchip,rk3036-sfc"; >> + reg = <0xff3a0000 0x4000>; >> + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>; >> + clock-names = "clk_sfc", "hclk_sfc"; > The clocks in the examples and dtsi files must have the same sort order. > >> + pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>; >> + pinctrl-names = "default"; >> + power-domains = <&power PX30_PD_MMC_NAND>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + flash@0 { > >From spi-controller.yaml: > > patternProperties: > "^.*@[0-9a-f]+$": > type: object > > properties: > compatible: > description: > Compatible of the SPI device. > > reg: > minimum: 0 > > maximum: 256 > > description: > Chip select used by the device. > > This allows 257 sub nodes. > Support up to 4 chip select in the driver. > #define SFC_MAX_CHIPSELECT_NUM 4 RK SFC design is up to 4 CS. Sorry, I don't see any specific improvement in this comment, can you explain it in detail. > >> + compatible = "jedec,spi-nor"; >> + reg = <0>; >> + spi-max-frequency = <108000000>; >> + spi-rx-bus-width = <2>; >> + spi-tx-bus-width = <2>; >> + }; >> + }; >> + >> +... >> > >
On 6/9/21 5:50 AM, Jon Lin wrote: > > On 6/9/21 2:03 AM, Johan Jonker wrote: >> Hi Jon, >> >> A look at the build log shows this error: >> >> https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20210608022644.21074-2-jon.lin@rock-chips.com/ >> >> >> dtschema/dtc warnings/errors: >> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml: >> >> spi@ff3a0000: clock-names:0: 'hclk_sfc' was expected >> From schema: >> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >> >> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml: >> >> spi@ff3a0000: clock-names:1: 'clk_sfc' was expected >> From schema: >> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >> >> >> Check document with: >> >> make ARCH=arm dt_binding_check >> DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >> >> make ARCH=arm dtbs_check >> DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >> >> make ARCH=arm64 dtbs_check >> DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >> >> Remove any errors before submitting. >> >> === >> >> Johan >> >> On 6/8/21 4:26 AM, Jon Lin wrote: >>> From: Chris Morgan <macromorgan@hotmail.com> >>> >>> Add bindings for the Rockchip serial flash controller. New device >>> specific parameter of rockchip,sfc-no-dma included in documentation. >>> >>> Signed-off-by: Chris Morgan <macromorgan@hotmail.com> >>> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> >>> --- >>> >>> Changes in v6: >>> - Add support in device trees for rv1126(Declared in series 5 but not >>> submitted) >>> - Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not >>> affect interpretation and has been widely used >>> - Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted) >>> - Simplify the code, such as remove "rockchip_sfc_register_all"(Declared >>> in series 5 but not submitted) >>> - Support SFC ver4 ver5(Declared in series 5 but not submitted) >>> - Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c >>> - Change to use devm_spi_alloc_master and spi_unregister_master >>> >>> Changes in v5: >>> - Add support in device trees for rv1126 >>> - Support sfc tx_dual, tx_quad >>> - Simplify the code, such as remove "rockchip_sfc_register_all" >>> - Support SFC ver4 ver5 >>> >>> Changes in v4: >>> - Changing patch back to an "RFC". An engineer from Rockchip >>> reached out to me to let me know they are working on this patch for >>> upstream, I am submitting this v4 for the community to see however >>> I expect Jon Lin (jon.lin@rock-chips.com) will submit new patches >>> soon and these are the ones we should pursue for mainlining. Jon's >>> patch series should include support for more hardware than this >>> series. >>> - Clean up documentation more and ensure it is correct per >>> make dt_binding_check. >>> - Add support in device trees for rk3036, rk3308, and rv1108. >>> - Add ahb clock (hclk_sfc) support for rk3036. >>> - Change rockchip_sfc_wait_fifo_ready() to use a switch statement. >>> - Change IRQ code to only mark IRQ as handled if it handles the >>> specific IRQ (DMA transfer finish) it is supposed to handle. >>> >>> Changes in v3: >>> - Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc). >>> - Changed the compatible string from rockchip,sfc to >>> rockchip,rk3036-sfc. A quick glance at the datasheets suggests this >>> driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and >>> RV1108 SoCs, and possibly more. However, I am currently only able >>> to test this on a PX30 (an RK3326). The technical reference manuals >>> appear to list the same registers for each device. >>> - Corrected devicetree documentation for formatting and to note these >>> changes. >>> - Replaced the maintainer with Heiko Stuebner and myself, as we will >>> take ownership of this going forward. >>> - Noted that the device (per the reference manual) supports 4 CS, but >>> I am only able to test a single CS (CS 0). >>> - Reordered patches to comply with upstream rules. >>> >>> Changes in v2: >>> - Reimplemented driver using spi-mem subsystem. >>> - Removed power management code as I couldn't get it working properly. >>> - Added device tree bindings for Odroid Go Advance. >>> >>> Changes in v1: >>> hanges made in this new series versus the v8 of the old series: >>> - Added function to read spi-rx-bus-width from device tree, in the >>> event that the SPI chip supports 4x mode but only has 2 pins >>> wired (such as the Odroid Go Advance). >>> - Changed device tree documentation from txt to yaml format. >>> - Made "reset" message a dev_dbg from a dev_info. >>> - Changed read and write fifo functions to remove redundant checks. >>> - Changed the write and read from relaxed to non-relaxed when >>> starting the DMA transfer or reading the DMA IRQ. >>> - Changed from dma_coerce_mask_and_coherent to just >>> dma_set_mask_and_coherent. >>> - Changed name of get_if_type to rockchip_sfc_get_if_type. >>> >>> .../devicetree/bindings/spi/rockchip-sfc.yaml | 87 +++++++++++++++++++ >>> 1 file changed, 87 insertions(+) >>> create mode 100644 >>> Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >>> >>> diff --git a/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >>> b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >>> new file mode 100644 >>> index 000000000000..160449713f97 >>> --- /dev/null >>> +++ b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml >>> @@ -0,0 +1,87 @@ >>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) >>> +%YAML 1.2 >>> +--- >>> +$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml# >>> +$schema: http://devicetree.org/meta-schemas/core.yaml# >>> + >>> +title: Rockchip Serial Flash Controller (SFC) >>> + >>> +maintainers: >>> + - Heiko Stuebner <heiko@sntech.de> >>> + - Chris Morgan <macromorgan@hotmail.com> >> In the driver spi-rockchip-sfc.c is used: >> Chris Morgan <macroalpha82@gmail.com> >> Maybe use a consistent email address? >> Also Hotmail does strange things to message-ID's and links/content >> inside patches. >> >>> + >>> +allOf: >>> + - $ref: spi-controller.yaml# >>> + >>> +properties: >>> + compatible: >>> + oneOf: >>> + - const: rockchip,rk3036-sfc >>> + - items: >>> + - enum: >>> + - rockchip,px30-sfc >>> + - rockchip,rk3308-sfc >>> + - rockchip,rv1108-sfc >>> + - const: rockchip,rk3036-sfc >>> + - const: rockchip,rv1126-sfc >> A look at the driver shows this: >> >> +static const struct of_device_id rockchip_sfc_dt_ids[] = { >> >> + { .compatible = "rockchip,px30-sfc"}, >> >> remove >> >> + { .compatible = "rockchip,rk3036-sfc"}, >> >> + { .compatible = "rockchip,rk3308-sfc"}, >> + { .compatible = "rockchip,rv1126-sfc"}, >> >> remove >> >> + { /* sentinel */ } >> +}; >> >> When no '.data = &my_sfc_data' exist then there's no need for additional >> compatible strings in the driver. >> === >> example for I2S: >> { .compatible = "rockchip,rk3399-i2s", .data = &rk3399_i2s_pins }, >> === >> Compatibility strings are supposed to be SoC orientated. >> With rockchip_sfc_get_version() all we need is one fall back string for >> now I think. Is rk3568 identical. Please advise. >> >> >> - const: rockchip,rk3036-sfc >> - items: >> - enum: >> - rockchip,px30-sfc >> - rockchip,rk3308-sfc >> - rockchip,rk3368-sfc >> - rockchip,rk3568-sfc >> - rockchip,rv1108-sfc >> - rockchip,rv1126-sfc >> - const: rockchip,rk3036-sfc >> >> === >> >> The rk3368 TRM also describes a SFC controller. >> For the mainline DT completeness is it possible to add a rk3368 SFC node >> as well? ;) >> >>> + >>> + reg: >>> + maxItems: 1 >>> + >>> + interrupts: >>> + maxItems: 1 >>> + >>> + clocks: >>> + items: >>> + - description: Bus Clock >>> + - description: Module Clock >>> + >>> + clock-names: >>> + items: >>> + - const: hclk_sfc >>> + - const: clk_sfc >>> + >>> + power-domains: >>> + maxItems: 1 >>> + >>> + rockchip,sfc-no-dma: >>> + description: Disable DMA and utilize FIFO mode only >>> + type: boolean >>> + >>> +required: >>> + - compatible >>> + - reg >>> + - interrupts >>> + - clocks >>> + - clock-names >>> + >>> +unevaluatedProperties: false >>> + >>> +examples: >>> + - | >>> + #include <dt-bindings/clock/px30-cru.h> >>> + #include <dt-bindings/interrupt-controller/arm-gic.h> >>> + #include <dt-bindings/power/px30-power.h> >>> + >>> + sfc: spi@ff3a0000 { >>> + compatible = "rockchip,px30-sfc","rockchip,rk3036-sfc"; >>> + reg = <0xff3a0000 0x4000>; >>> + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; >>> + clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>; >>> + clock-names = "clk_sfc", "hclk_sfc"; >> The clocks in the examples and dtsi files must have the same sort order. >> >>> + pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>; >>> + pinctrl-names = "default"; >>> + power-domains = <&power PX30_PD_MMC_NAND>; >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + >>> + flash@0 { >> >From spi-controller.yaml: >> >> patternProperties: >> "^.*@[0-9a-f]+$": >> type: object >> >> properties: >> compatible: >> description: >> Compatible of the SPI device. >> >> reg: >> minimum: 0 >> >> maximum: 256 >> >> description: >> Chip select used by the device. >> >> This allows 257 sub nodes. >> Support up to 4 chip select in the driver. >> #define SFC_MAX_CHIPSELECT_NUM 4 > RK SFC design is up to 4 CS. > > Sorry, I don't see any specific improvement in this comment, can you > explain it in detail. In the old text documents it only described the hardware. With the new YAML format we also check new dts submissions for bogus properties. So if someone comes up with this example: flash@88 { compatible = "jedec,spi-nor"; reg = <0x88>; } This must give a out of range notification. Also when someone tries to connect something else then flash that must be detected. The spi-controller.yaml allows any node name. patternProperties: "^flash@[0-3]$": type: object properties: compatible: const: jedec,spi-nor reg: minimum: 0 maximum: 3 === Example from rockchip,nand-controller.yaml: patternProperties: "^nand@[0-7]$": type: object properties: reg: minimum: 0 maximum: 7 === >> >>> + compatible = "jedec,spi-nor"; >>> + reg = <0>; >>> + spi-max-frequency = <108000000>; >>> + spi-rx-bus-width = <2>; >>> + spi-tx-bus-width = <2>; >>> + }; >>> + }; >>> + >>> +... >>> >> >> > >
diff --git a/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file mode 100644 index 000000000000..160449713f97 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip Serial Flash Controller (SFC) + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + - Chris Morgan <macromorgan@hotmail.com> + +allOf: + - $ref: spi-controller.yaml# + +properties: + compatible: + oneOf: + - const: rockchip,rk3036-sfc + - items: + - enum: + - rockchip,px30-sfc + - rockchip,rk3308-sfc + - rockchip,rv1108-sfc + - const: rockchip,rk3036-sfc + - const: rockchip,rv1126-sfc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: hclk_sfc + - const: clk_sfc + + power-domains: + maxItems: 1 + + rockchip,sfc-no-dma: + description: Disable DMA and utilize FIFO mode only + type: boolean + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/px30-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/px30-power.h> + + sfc: spi@ff3a0000 { + compatible = "rockchip,px30-sfc","rockchip,rk3036-sfc"; + reg = <0xff3a0000 0x4000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>; + clock-names = "clk_sfc", "hclk_sfc"; + pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>; + pinctrl-names = "default"; + power-domains = <&power PX30_PD_MMC_NAND>; + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <108000000>; + spi-rx-bus-width = <2>; + spi-tx-bus-width = <2>; + }; + }; + +...