| Message ID | 20210608104128.1616028-2-martin.kepplinger@puri.sm (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | media: imx: add support for imx8mq MIPI RX | expand |
On Tue, Jun 08, 2021 at 12:41:26PM +0200, Martin Kepplinger wrote: > The i.MX8MQ SoC integrates a different MIPI CSI receiver as the i.MX8MM so > describe the DT bindings for it. > > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> > --- > .../bindings/media/nxp,imx8mq-mipi-csi2.yaml | 161 ++++++++++++++++++ > 1 file changed, 161 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml > > diff --git a/Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml > new file mode 100644 > index 000000000000..6eafdf803d36 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml > @@ -0,0 +1,161 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/media/nxp,imx8mq-mipi-csi2.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: NXP i.MX8MQ MIPI CSI-2 receiver > + > +maintainers: > + - Martin Kepplinger <martin.kepplinger@puri.sm> > + > +description: |- > + This binding covers the CSI-2 RX PHY and host controller included in the > + NXP i.MX8MQ SoC. It handles the sensor/image input and process for all the > + input imaging devices. > + > +properties: > + compatible: > + enum: > + - fsl,imx8mq-mipi-csi2 > + > + reg: > + maxItems: 1 > + > + clocks: > + items: > + - description: core is the RX Controller Core Clock input. This clock > + must be exactly equal to or faster than the receive > + byteclock from the RX DPHY. > + - description: esc is the Rx Escape Clock. This must be the same escape > + clock that the RX DPHY receives. > + - description: pxl is the pixel clock (phy_ref up to 333Mhz). > + - description: clko2 is the CLKO2 clock root. > + See the reference manual for details. > + > + clock-names: > + items: > + - const: core > + - const: esc > + - const: pxl > + - const: clko2 > + > + power-domains: > + maxItems: 1 > + > + reset: resets > + description: > + The phandle to the imx8mq reset-controller. Drop. What the reset controller is is out of scope for a binding. > + maxItems: 1 > + > + phy: phys? Assuming this is using the PHY binding. If it is not, then why not? > + description: > + The phandle to the imx8mq syscon iomux-gpr. > + maxItems: 1 > + > + interconnects: > + maxItems: 1 > + > + interconnect-names: > + const: dram > + > + ports: > + $ref: /schemas/graph.yaml#/properties/ports > + > + properties: > + port@0: > + $ref: /schemas/graph.yaml#/$defs/port-base > + unevaluatedProperties: false > + description: > + Input port node, single endpoint describing the CSI-2 transmitter. > + > + properties: > + endpoint: > + $ref: video-interfaces.yaml# > + unevaluatedProperties: false > + > + properties: > + data-lanes: > + items: > + minItems: 1 > + maxItems: 4 > + items: > + - const: 1 > + - const: 2 > + - const: 3 > + - const: 4 > + > + required: > + - data-lanes > + > + port@1: > + $ref: /schemas/graph.yaml#/properties/port > + description: > + Output port node > + > + required: > + - port@0 > + - port@1 > + > +required: > + - compatible > + - reg > + - clocks > + - clock-names > + - power-domains > + - reset > + - phy > + - ports > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/imx8mq-clock.h> > + #include <dt-bindings/interconnect/imx8mq.h> > + > + csi@30a70000 { > + compatible = "fsl,imx8mq-mipi-csi2"; > + reg = <0x30a70000 0x1000>; > + clocks = <&clk IMX8MQ_CLK_CSI1_CORE>, > + <&clk IMX8MQ_CLK_CSI1_ESC>, > + <&clk IMX8MQ_CLK_CSI1_PHY_REF>, > + <&clk IMX8MQ_CLK_CLKO2>; > + clock-names = "core", "esc", "pxl", "clko2"; > + assigned-clocks = <&clk IMX8MQ_CLK_CSI1_CORE>, > + <&clk IMX8MQ_CLK_CSI1_PHY_REF>, > + <&clk IMX8MQ_CLK_CSI1_ESC>; > + assigned-clock-rates = <266000000>, <200000000>, <66000000>; > + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>, > + <&clk IMX8MQ_SYS2_PLL_1000M>, > + <&clk IMX8MQ_SYS1_PLL_800M>; > + power-domains = <&pgc_mipi_csi1>; > + reset = <&src>; > + phy = <&iomuxc_gpr>; > + interconnects = <&noc IMX8MQ_ICM_CSI1 &noc IMX8MQ_ICS_DRAM>; > + interconnect-names = "dram"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + imx8mm_mipi_csi_in: endpoint { > + remote-endpoint = <&imx477_out>; > + data-lanes = <1 2 3 4>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + imx8mm_mipi_csi_out: endpoint { > + remote-endpoint = <&csi_in>; > + }; > + }; > + }; > + }; > + > +... > -- > 2.30.2
diff --git a/Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml new file mode 100644 index 000000000000..6eafdf803d36 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml @@ -0,0 +1,161 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nxp,imx8mq-mipi-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP i.MX8MQ MIPI CSI-2 receiver + +maintainers: + - Martin Kepplinger <martin.kepplinger@puri.sm> + +description: |- + This binding covers the CSI-2 RX PHY and host controller included in the + NXP i.MX8MQ SoC. It handles the sensor/image input and process for all the + input imaging devices. + +properties: + compatible: + enum: + - fsl,imx8mq-mipi-csi2 + + reg: + maxItems: 1 + + clocks: + items: + - description: core is the RX Controller Core Clock input. This clock + must be exactly equal to or faster than the receive + byteclock from the RX DPHY. + - description: esc is the Rx Escape Clock. This must be the same escape + clock that the RX DPHY receives. + - description: pxl is the pixel clock (phy_ref up to 333Mhz). + - description: clko2 is the CLKO2 clock root. + See the reference manual for details. + + clock-names: + items: + - const: core + - const: esc + - const: pxl + - const: clko2 + + power-domains: + maxItems: 1 + + reset: + description: + The phandle to the imx8mq reset-controller. + maxItems: 1 + + phy: + description: + The phandle to the imx8mq syscon iomux-gpr. + maxItems: 1 + + interconnects: + maxItems: 1 + + interconnect-names: + const: dram + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + minItems: 1 + maxItems: 4 + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Output port node + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - clocks + - clock-names + - power-domains + - reset + - phy + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mq-clock.h> + #include <dt-bindings/interconnect/imx8mq.h> + + csi@30a70000 { + compatible = "fsl,imx8mq-mipi-csi2"; + reg = <0x30a70000 0x1000>; + clocks = <&clk IMX8MQ_CLK_CSI1_CORE>, + <&clk IMX8MQ_CLK_CSI1_ESC>, + <&clk IMX8MQ_CLK_CSI1_PHY_REF>, + <&clk IMX8MQ_CLK_CLKO2>; + clock-names = "core", "esc", "pxl", "clko2"; + assigned-clocks = <&clk IMX8MQ_CLK_CSI1_CORE>, + <&clk IMX8MQ_CLK_CSI1_PHY_REF>, + <&clk IMX8MQ_CLK_CSI1_ESC>; + assigned-clock-rates = <266000000>, <200000000>, <66000000>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>, + <&clk IMX8MQ_SYS2_PLL_1000M>, + <&clk IMX8MQ_SYS1_PLL_800M>; + power-domains = <&pgc_mipi_csi1>; + reset = <&src>; + phy = <&iomuxc_gpr>; + interconnects = <&noc IMX8MQ_ICM_CSI1 &noc IMX8MQ_ICS_DRAM>; + interconnect-names = "dram"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + imx8mm_mipi_csi_in: endpoint { + remote-endpoint = <&imx477_out>; + data-lanes = <1 2 3 4>; + }; + }; + + port@1 { + reg = <1>; + + imx8mm_mipi_csi_out: endpoint { + remote-endpoint = <&csi_in>; + }; + }; + }; + }; + +...
The i.MX8MQ SoC integrates a different MIPI CSI receiver as the i.MX8MM so describe the DT bindings for it. Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> --- .../bindings/media/nxp,imx8mq-mipi-csi2.yaml | 161 ++++++++++++++++++ 1 file changed, 161 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml